A geometric assessment method for estimating dimensional change of retrieved dual mobility liners for total hip arthroplasty

Despite their emerging use, the current understanding of the in-vivo functional mechanisms of Dual Mobility (DM) Total Hip Replacements (THRs) is poor, and current characterisation methodologies are not suitable for the unique function and design of these types of devices. Therefore, the aim of this study was to develop a geometric characterisation methodology to estimate dimensional change across the articulating surfaces of retrieved DM polyethylene liners so that their invivo function may be better understood. The method involves the acquisition of three-dimensional coordinate data from the internal and external surfaces of DM liners. The data is processed using a bespoke MATLAB script which approximates the unworn reference geometry of each surface, calculates geometric variance at each point and produces surface deviation heatmaps so that areas of wear and/or deformation may be visualised across the implant. One as-manufactured and five retrieved DM liners were assessed, which demonstrated the efficacy, repeatability and sensitivity of the developed method. This study describes an automated and non-destructive approach for assessing retrieved DM liners of any size and from any manufacturer, which may be used in future research to improve our understanding of their in-vivo function and failure mechanisms.

Inertial Tracking System for Monitoring Dual Mobility Hip Implants In Vitro

Dual mobility (DM) implants are being increasingly used for total hip arthroplasties due to the additional range of motion and joint stability they afford over more traditional implant types. Currently, there are no reported methods for monitoring their motions under realistic operating conditions while in vitro and, therefore, it is challenging to predict how they will function under clinically relevant conditions and what failure modes may exist. This study reports the development, calibration, and validation of a novel inertial tracking system that directly mounts to the mobile liner of DM implants. The tracker was custom built and based on a miniaturized, off-the-shelf inertial measurement unit (IMU) and employed a gradient-decent sensor fusion algorithm for amalgamating nine degree-of-freedom IMU readings into three-axis orientation estimates. Additionally, a novel approach to magnetic interference mitigation using a fixed solenoid and magnetic field simulation was evaluated. The system produced orientation measurements to within 1.0° of the true value under ideal conditions and 3.9° with a negligible drift while in vitro, submerged in lubricant, and without a line of sight.

Risk Factors for Significant Radiolucent Line Development in a Fully Coated Hydroxyapatite Stem

BACKGROUND

The risk factors for and clinical impact of radiolucent lines (RLLs) in cementless total hip arthroplasty remain contentious. The aim of this work was to describe a method of classification that has clinical significance and to identify risk factors.

METHODS

A cohort of 288 subjects with unrevised Corail stems (DePuy Synthes, Warsaw, IN) were reviewed with radiographs and Oxford Hip Scores at 10 years. Based on clinical experience, three groups were defined; those with no RLLs (NoRLLs), those considered to have benign RLLs (BenRLLs), and those considered to have significant RLLs (SigRLLs). SigRLLs were then compared to BenRLLs and NoRLLs to determine the validity of this classification.

RESULTS

One hundred and nine (37.8%) had NoRLLs, 111 (38.5%) had BenRLLs, and 68 (23.6%) had SigRLLs. No significant difference apart from gender was noted between the occurrence of BenRLLs and NoRLLs after multinomial regression analysis, consequently the NoRLLs and BenRLLs groups were combined (NoSigRLLs) and compared to SigRLLs. Non-cross-linked polyethylene (odds ratio = 4.6, P < .001), collarless stem design (odds ratio = 9.4, P < .001), undersizing (odds ratio = 1.2, P = .028), and male sex (odds ratio = 2.1, P = .008) were risk factors for SigRLLs. Regression analysis also revealed that increasing age at operation decreased the likelihood of SigRLLs (P < .001). Patients with SigRLLs had significantly higher pain scores (P = .005) although overall Oxford Hip Scores were not significantly different (P = .364).

CONCLUSION

The definition of SigRLLs proposed in this study was significantly associated with that of non-cross-linked polyethylene, absence of a collar, undersizing, and higher pain scores.

Computationally efficient modelling of hip replacement separation due to small mismatches in component centres of rotation

Patient imaging and explant analysis has shown evidence of edge loading of hard-on-hard hip replacements in vivo. Experimental hip simulator testing under edge loading conditions has produced increased, clinically-relevant, wear rates for hard-on-hard bearings when compared to concentric conditions. Such testing, however, is time consuming and costly. A quick running computational edge loading model (Python Edge Loading (PyEL) - quasi-static, rigid, frictionless), capable of considering realistic bearing geometries, was developed. The aim of this study was to produce predictions of separation within the typical experimental measurement error of ∼0.5 mm. The model was verified and validated against comparable finite element (FE) models (including inertia and friction) and pre-existing experimental test data for 56 cases, covering a variety of simulated cup orientations, positions, tissue tensions, and loading environments. The PyEL model agreed well with both the more complex computational modelling and experimental results. From comparison with the FE models, the assumption of no inertia had little effect on the maximum separation prediction. With high contact force cases, the assumption of no friction had a larger effect (up to ∼5% error). The PyEL model was able to predict the experimental maximum separations within ∼0.3 mm. It could therefore be used to optimise an experimental test plan and efficiently investigate a much wider range of scenarios and variables. It could also help explain trends and damage modes seen in experimental testing through identifying the contact locations on the liner that are not easily measured experimentally.

Finite element analysis of polyethylene wear in total hip replacement: A literature review

Evaluation and prediction of wear play a key role in product design and material selection of total hip replacements, because wear debris is one of the main causes of loosening and failure. Multifactorial clinical or laboratory studies are high cost and require unfeasible timeframes for implant development. Simulation using finite element methods is an efficient and inexpensive alternative to predict wear and pre-screen various parameters. This article presents a comprehensive literature review of the state-of-the-art finite element modelling techniques that have been applied to evaluate wear in polyethylene hip replacement components. A number of knowledge gaps are identified including the need to develop appropriate wear coefficients and the analysis of daily living activities.

Wear of different materials for total hip replacement under adverse stop-dwell-start in vitro wear simulation conditions

Hip simulation is a common technique for pre-clinical evaluation of wear performance of total hip arthroplasty. Standard techniques replicate kinematics of walking patterns of a typical patient. Attention has focussed in developing simulations of other typical patient daily activities to improve accuracy of wear predictions. A method for simulating stop-dwell-start motion during patient walking and the effect on 36-mm metal-on-metal total hip arthroplasty was previously presented by the authors. This study sought to extend the previous work to look at the effect of these conditions on ceramic-on-ceramic, metal-on-polyethylene and ceramic-on-polyethylene bearings. Two stop-dwell-start protocols were used: one reproducing average patient movement patterns and one examining more severe conditions. For all materials tested, no significant increase in wear was observed under average stop-dwell-start conditions, suggesting the bearing types tested are robust to this type of activity. A significant increase in wear was observed for metal-on-metal, metal-on-polyethylene and ceramic-on-polyethylene bearings under severe stop-dwell-start conditions, this was attributed to depletion of lubricant in the bearing during the dwell period. A greater relative increase in wear was observed for metal-on-metal bearings compared with metal-on-polyethylene and ceramic-on-polyethylene bearings. This may be explained by the contributions of the different lubrication mechanisms in each bearing type. Wear of ceramic-on-ceramic was very low in all tests, suggesting normal measurement variation was masking any effect of the adverse conditions. It was not possible to determine any effect of the different activities. These results emphasise the importance of exploring adverse patient activity simulations. The increase in wear rate associated with an adverse activity such as seen in stop-dwell-start motion, has to be considered in the context of the frequency of the adverse activity cycle relative to other activities such as standard continuous walking, to determine the impact on the total wear in a given time period.

Comparative study of material loss at the taper interface in retrieved metal-on-polyethylene and metal-on-metal femoral components from a single manufacturer

There have been a number of reports on the occurrence of taper corrosion and/or fretting and some have speculated on a link to the occurrence of adverse local tissue reaction specifically in relation to total hip replacement which have a metal-on-metal bearing. As such a study was carried out to compare the magnitude of material loss at the taper in a series of retrieved femoral heads used in metal-on-polyethylene bearings with that in a series of retrieved heads used in metal-on-metal bearings. A total of 36 metal-on-polyethylene and 21 metal-on-metal femoral components were included in the study all of which were received from a customer complaint database. Furthermore, a total of nine as-manufactured femoral components were included to provide a baseline for characterisation. All taper surfaces were assessed using an established corrosion scoring method and measurements were taken of the female taper surface using a contact profilometry. In the case of metal-on-metal components, the bearing wear was also assessed using coordinate metrology to determine whether or not there was a relationship between bearing and taper material loss in these cases. The study found that in this cohort the median value of metal-on-polyethylene taper loss was 1.25 mm³ with the consequent median value for metal-on-metal taper loss being 1.75 mm³. This study also suggests that manufacturing form can result in an apparent loss of material from the taper surface determined to have a median value of 0.59 mm³. Therefore, it is clear that form variability is a significant confounding factor in the measurement of material loss from the tapers of femoral heads retrieved following revision surgery.

Wear of surface-engineered metal-on-metal bearings for hip prostheses under adverse conditions with the head loading on the rim of the cup

Clinical studies have found high wear rates, elevated ion levels and high revision rates of large-diameter metal-on-metal surface replacement bearings in some patients, which have been associated with edge loading of the head on the rim of the cup. We have simulated increased wear and ion levels in metal-on-metal bearings in vitro by introducing variations in translational and rotational positioning of the components, which reproduces stripe wear on the femoral head, cup rim wear and clinically relevant large as well as small wear particles. There is interest in technologies such as surface engineering, which might reduce metal wear and the release of wear particles and ions. Reduced wear with surface-engineered surface replacements compared to metal-on-metal controls has been reported under standard walking conditions with correctly aligned and concentric components. In this in vitro study, the wear of chromium nitride surface-engineered metal-on-metal bearings under conditions of microseparation associated with translational and rotational malpositioning of the components was investigated and the results were compared with a previously reported study of metal-on-metal bearings under the same conditions. Simulations were conducted using our unique hip simulation microseparation methodologies, which reproduce accelerated wear in metal-on-metal bearings and have previously been clinically validated with ceramic-on-ceramic bearings. Four of the six surface-engineered bearings had evidence of head contact on the rim of the cup, which produced stripe wear on the femoral head. Four of the six surface-engineered bearings (two without stripe and two with stripe wear) had lower wear than the previously reported high wearing metal-on-metal bearings. At 2 million cycles, two of the surface-engineered bearings had substantially increased wear rates, four times higher than the high wear rates previously reported for metal-on-metal bearings under the same conditions. There was wear through and cohesive failure of the thick atomic emission physical vapour deposition (AEPVD) chromium nitride (CrN) coating. At this point, the study was stopped to investigate the failure mode. This study highlights the need to pre-clinically investigate the tribology of new bearings under a wide set of clinical conditions as demonstrated by our stratified approach for enhanced reliability (SAFER) simulation methods. In adopting this SAFER approach to pre-clinical simulation testing of new bearings, it is important to communicate the failures as well as successes of technologies arising from the research, in order that the wider community can benefit from the analysis of the pre-clinical failure modes.

High cup angle and microseparation increase the wear of hip surface replacements

High wear rates and high patient ion levels have been associated with high (> 55 degrees) cup inclination angles for metal-on-metal surface replacements. Wear rates and patterns have been simulated for ceramic-on-ceramic bearings by applying microseparation to replicate head offset deficiency. We tested 39-mm metal-on-metal surface replacements (n = 5) in a hip simulator with (A) an increased cup inclination angle of 60 degrees and (B) an increased cup inclination angle and microseparation over 2 million cycles. (A) resulted in a ninefold increase in wear rate and (B) resulted in a 17-fold increase in wear rate compared to a standard gait condition study. Wear particles produced under microseparation conditions were larger than those produced under standard conditions but of similar shape (round to oval). The data suggest both head and cup position influence the wear of surface replacements; we believe it likely bearings with high wear either have a high cup inclination angle, an offset deficient head, or a combination of both.

Comparison of wear of ultra-high molecular weight polyethylene acetabular cups against surface-engineered femoral heads

Alumina ceramic heads have been previously shown to reduce polyethylene wear in comparison to cobalt chrome (CoCr) heads in artificial hip joints. However, there are concerns about the brittle nature of ceramics. It is therefore of interest to investigate ceramic-like coatings on metallic heads. The aim of this study was to compare the friction and wear of ultra-high molecular weight polyethylene (UHMWPE) against alumina ceramic, CoCr, and surface-engineered ceramic-like coatings in a friction simulator and a hip joint simulator. All femoral heads tested were 28 mm diameter and included: Biolox Forte alumina, CoCr, arc evaporative physical vapour deposition (AEPVD) chromium nitride (CrN) coated CoCr, plasma-assisted chemical vapour deposition (PACVD) amorphous diamond-like carbon (aDLC) coated CoCr, sputter CrN coated CoCr, reactive gas controlled arc (RGCA) AEPVD titanium nitride (TiN) coated CoCr, and Graphit-iC coated CoCr. These were articulated against UHMWPE acetabular cups in a friction simulator and a hip joint simulator. Alumina and CoCr gave the lowest wear volumes whereas the sputter coated CrN gave the highest. Alumina also had the lowest friction factor. There was an association between surface parameters and wear. This study indicates that surface topography of surface-engineered femoral heads is more important than friction and wettability in controlling UHMWPE wear.

Effect of bearing size on the long-term wear, wear debris, and ion levels of large diameter metal-on-metal hip replacements-An in vitro study

Hip resurfacing arthroplasty has become a popular alternative to conventional hip surgery. Surface replacements with bearing sizes of 55 mm (n = 5) and 39 mm (n = 5) were tested in a hip simulator for 15 million cycles (Mc). Wear debris was isolated from the serum lubricant and characterized by field emmitting gun scanning electorn microscopy, and ion levels were measured via inductively coupled plasma mass spectroscopy at intervals throughout the test. The 39 mm bearings showed significantly greater bedding in volumetric wear (2.58 mm(3)) compared with the 55 mm bearings (1.15 mm(3)). There was no significant difference between the steady state wear rates (1-15 Mc) between the two sizes (0.10 and 0.09 mm(3)/Mc, respectively); however, this parity only became clear after 7 Mc. The wear debris isolated was oval in morphology with a mean particle size of 28 nm and a range of 9-108 nm. The Co levels measured at 0.13 Mc were significantly greater than at 3.6 Mc for both bearing sizes (10926 ppb and 176 ppb, respectively). After 0.5 Mc, the Co levels from the 39 mm bearings were significantly higher than the 55 mm (11,007 vs. 1475 ppb). The wear results support previous findings showing that increasing the femoral head size decreased volumetric bedding in wear. The ion levels measured suggest both bearing sizes have similar initial wear rates; however, the 55 mm bearings reach steady state wear more rapidly.

Tribology and wear of metal-on-metal hip prostheses: influence of cup angle and head position

BACKGROUND

Clinical studies have indicated that the angular position of the acetabular cup may influence wear in metal-on-metal total hip bearings. A high cup angle in comparison to the anatomical position may lead to the head being constrained by the superior lateral surface and rim of the cup, thus potentially changing the location of the contact zone between the head and the cup. The aim of this study was to test the hypothesis that both a steep cup angle and a lateralized position of the head can increase head contact on the superior rim of the cup, with the consequence of increased wear.

METHODS

Hip-joint simulator studies of metal-on-metal bearings were undertaken with cup angles of 45 degrees and 55 degrees . The femoral head was either aligned to the center of the cup or placed in a position of microlateralization. Wear was measured gravimetrically over 5 million cycles.

RESULTS

A steep cup angle of 55 degrees showed significantly higher long-term steady-state wear than a standard cup angle of 45 degrees (p < 0.01). The difference was fivefold. Microlateralization of the head resulted in a fivefold increase in steady-state wear compared with a centralized head. The combination of a steep cup angle and a microlateralized head increased the steady-state wear rate by tenfold compared with a standard cup angle with a centralized head.

CONCLUSIONS

These studies support the hypothesis that both an increased cup angle and a lateral head position increase wear in metal-on-metal hip prostheses.

Friction of total hip replacements with different bearings and loading conditions

Metal-on-ultra-high molecular weight polyethylene (UHMWPE) total hip replacements have been the most popular and clinically successful implants to date. However, it is well documented that the wear debris from these prostheses contributes to osteolysis and ultimate failure of the prosthesis, hence alternative materials have been sought. A range of 28 mm diameter bearings were investigated using a hip friction simulator, including conventional material combinations such as metal-on-UHWMPE, ceramic-on-ceramic (CoC), and metal-on-metal (MoM), as well as novel ceramic-on-metal (CoM) pairings. Studies were performed under different swing-phase load and lubricant conditions. The friction factors were lowest in the ceramic bearings, with the CoC bearing having the lowest friction factor in all conditions. CoM bearings also had low friction factors compared with MoM, and the trends were similar to CoC bearings for all test conditions. Increasing swing phase load was shown to cause an increase in friction factor in all tests. Increased serum concentration resulted in increased friction factor in all material combinations, except MoM, where increased serum concentration produced a significant reduction in friction factor.

Deformation of press-fitted metallic resurfacing cups. Part 1: Experimental simulation

The interference press fit of a metallic one-piece acetabular cup employed for metal-on-metal hip resurfacing procedures was investigated experimentally under laboratory conditions in the present study, in particular regarding the cup deformation. Tests were carried out in cadavers as well as polyurethane foams of various grades with different elastic moduli to represent different cancellous bone qualities. The cadaver test was used to establish the most suitable configuration of the foam model representing realistic support and geometrical conditions at the pelvis. It was found that a spherical cavity, with two identical areas relieved on opposite sides, was capable of creating a two-point pinching action of the ischeal and ilial columns on the cup as the worst-case scenario. Furthermore, the cup deformation produced from such a two-point loading model with a grade 30 foam was similar to that measured from the cadaver test. Therefore, such a protocol was employed in subsequent experimental tests. For a given size of the outside diameter of the cup of 60 mm, the cup deflection was shown to be dependent largely on the cup wall thickness and the diametral interference between cup and prepared cavity at implantation. For a relatively thin cup with a wall thickness between 2.3 mm (equator) and 4 mm (pole) and with a modest nominal diametral interference of 1 mm, which corresponds to an actual interference of approximately 0.5 mm, the maximum diametral cup deflection (at the rim) was around 60 μm, compared with a diametral clearance of 80-120 μm between the femoral head and the acetabular cup, generally required for fluid-film lubrication and tribological performances. Stiffening of the cup, by both thickening and lateralizing by 1 mm, reduced the cup deformation to between 30 and 50 μm with actual diametral interferences between 0.5 and 1 mm.

Deformation of press-fitted metallic resurfacing cups. Part 2: Finite element simulation

The deformation of metallic acetabular cups employed for metal-on-metal hip resurfacing procedures was considered theoretically using the finite element method in the present study, following on the experimental investigation reported in Part 1. Three representative cups, characterized by the cup wall thickness as thin, intermediate, and thick, were considered. For the intermediate cup, the effects of both the size and the diametral interference on the cup deformation were investigated. Both two-dimensional axisymmetric and three-dimensional finite element models were developed to examine the important parameters during and after the press-fit procedure, and in particular the deformation of the metallic cup. The theoretical prediction of the cup deformation was in reasonable agreement with the corresponding experimental measurement reported in Part 1. The most significant factor influencing the cup deformation was the cup wall thickness. Both the size and the diametral interference were also shown to influence the cup deformation. It is important to ensure that the cup deformation does not significantly affect the clearance designed and optimized for tribological performances of metal-on-metal hip resurfacing prostheses. Furthermore the contact parameters at the cup and bone interface associated with the press fit were also discussed.

Comparative wear under different conditions of surface-engineered metal-on-metal bearings for total hip arthroplasty

Metal-on-metal hip arthroplasties have demonstrated low wear rates. However, the ion release and toxicity of the metal wear particles remains a concern. Modifying the surface of metal bearings with thick chromium nitride (CrN) coatings has the potential to further reduce wear and ion release, and improve the biocompatibility of wear particles produced. The aim of this study was to investigate the application of surface engineering technology to modify metal-on-metal (MOM) bearings to reduce wear and improve the functional biocompatibility of metal-on-metal prostheses. CrN-on-CrN bearings had lower wear rates in comparison to metal-on-metal bearings, particularly under adverse loading conditions. CrN-on-CrN bearings produced similar nanometer-sized particles to metal-on-metal bearings, however, CrN wear particles were less cytotoxic when cocultured with macrophage and fibroblast cells.

Tc-HMPAO SPECT in persistent post-concussion syndrome after mild head injury: comparison with MRI/CT

The purposes of this study were: (1) to determine the prevalence of abnormal 99mTc-HMPAO SPECT scans in patients suffering from persistent post-concussive syndrome (PPCS) after mild closed head injury (CHI); (2) to compare SPECT with structural neuroimaging (MRI and CT) in patients with mild CHI; and (3) to investigate correlations between SPECT and clinical data obtained from the patient sample (neuropsychological testing, demographics, psychiatric diagnoses). Forty-three patients were included. SPECT was read as abnormal in 53% of patients and showed a total of 37 lesions while MRI was read as abnormal in 9% and CT scan in only 4.6% of patients after mild CHI. SPECT appears to be more sensitive in detecting cerebral abnormalities after mild CHI, especially in patients with PPCS symptoms, than either CT or MRI. No statistically significant relationship was found between SPECT scan abnormalities and age, past psychiatric history, history of substance abuse, or history of multiple CHI. Education level did not differ between patients with normal and abnormal SPECT. Current neuropsychiatric symptoms did not seem to have any impact on the results of SPECT scan.

Is bipolar disorder the most common diagnostic entity in hospitalized adolescents and children?

An evaluation of all children and adolescents admitted to an acute psychiatric unit over a three-month period was undertaken to determine the presence of bipolar disorder. The findings indicated that bipolar disorder was the most common diagnostic entity. This disorder had not been recognized in most of these youngsters previously, although almost all of them have had past psychiatric contacts. The vast majority of youngsters experiencing delusions and/or hallucinations, and the vast majority of court-remanded adolescents also appeared to be suffering from the disorder. It was concluded that bipolar disorder has to be ruled out in all youngsters admitted to acute care psychiatric units.

N-ras mutations are associated with poor prognosis and increased risk of leukemia in myelodysplastic syndrome

To evaluate the clinical significance of N-ras mutations in the myelodysplastic syndrome (MDS) archival bone marrow samples from 252 patients were studied for the presence of N-ras exon I mutations using polymerase chain reaction amplification and differential oligonucleotide hybridization. Subsequently, clinical information about these patients was obtained and analyzed. Of 220 evaluable patients, 20 (9%) had point mutation of N-ras involving codon 12. Individuals with N-ras mutation had a significantly shorter survival period than those who were N-ras negative (P = .02). An increased risk of acute myelogenous leukemia (AML) was also found in patients with N-ras mutations (P = .005). N-ras mutations were not associated with any French-American-British (FAB) subtype, with the presence of increased myeloblasts, or with chromosomal aberrations in the bone marrow. However, the presence of increased bone marrow blasts was strongly associated with poor survival rate and risk of AML (P < .001 for each). After stratifying for the percentage of blasts, N-ras mutations remained significantly associated with shorter survival period (P = .04) and increased risk of AML (P = .02). Bone marrow cytogenetic abnormalities, particularly when multiple abnormalities were present, were significantly associated with a poor prognosis (P < .001). In conclusion, N-ras mutation, although relatively infrequent in MDS, is associated with short survival period and increased probability of developing AML.

Religious variables are infrequently reported in clinical research

BACKGROUND

More than 200 published studies have found some relationship between an individual's religion and health, yet reference to religious variables rarely appears in published empirical studies.

METHODS

We performed a manual search of all articles reporting on human subjects in the 1989 issues of seven major medical journals to record and analyze religious and other demographic variables.

RESULTS

Only 12 of the 1,066 articles (1.1%) mentioned religion, and eight of these mentioned only denominational affiliation.

CONCLUSION

Most clinical investigators do not report on the religious variables of their subjects and thus may be missing important correlations.

Misdiagnosed bipolar disorder in adolescents in a special educational school and treatment program

BACKGROUND

Twelve adolescents found to be the most problematic, crisis prone, and treatment resistant were comprehensively reevaluated in the special educational day school and treatment program they were attending. This reevaluation took place over a 6-month period and was done to arrive upon a more comprehensive diagnostic understanding so that more relevant and effective treatment measures could be instituted.

METHOD

The author conducted semistructured interviews with the adolescents on multiple occasions as the clinical situations warranted. All information available, recorded or otherwise, was comprehensively reviewed and reevaluated. The children were observed informally in and out of their classrooms throughout the period. All parents available were interviewed to clarify the children's present and past symptomatology and to assess the nature of psychiatric disorders, if any, in first- and second-degree family members.

RESULTS

The reevaluation showed that 8 of the 12 youngsters clearly satisfied DSM-III-R criteria for bipolar disorder, which had been misdiagnosed mainly as attention-deficit hyperactivity disorder (ADHD) and conduct disorder. Three other youngsters showed significant bipolar features though not fully satisfying the criteria for this disorder.

CONCLUSION

Bipolar disorder may be very common among highly problematic adolescents in special educational and outpatient treatment facilities for emotionally disturbed youngsters but may still be misdiagnosed very often as ADHD and conduct disorder, with all the negative consequences of such misdiagnosis.

Drug-induced hypokalaemia. A cause for concern

Drug-induced hypokalaemia is a widespread problem in the elderly that can be caused by many therapeutically useful substances, the most common of which are diuretics. In certain classes of patients (e.g. those with acute myocardial infarction, with congestive heart failure receiving digitalis, or with cirrhosis), iatrogenic hypokalaemia is an established risk factor. In patients with hypertension who have no underlying heart disease or liver disease, the use of diuretics may lead to worsened glucose tolerance and cardiac arrhythmias. There is also evidence for an increased risk of sudden cardiac death.

Bipolar disorder in prepubertal children in a special educational setting: is it rare?

The author undertook a comprehensive clinical reevaluation of five prepubertal children attending a special educational class for emotionally disturbed children in a day program. The children had failed to improve or had continued to worsen despite years of treatment in multiple settings. This extensive reevaluation and observation, spanning many months, revealed that all of the children met DSM-III-R criteria for bipolar disorder (lifetime prevalence). None of the children had been previously diagnosed with this disorder. The author's finding suggests that bipolar disorder may be more common in severely problematic prepubertal children than is generally recognized. The implications of this and related issues are discussed.