Transhumeral prosthesis use affects upper body kinematics and kinetics

BACKGROUND

Transhumeral (TH) limb loss leads to loss of body mass and reduced shoulder range of motion. Despite most owning a prosthesis, prosthesis abandonment is common. The consequence of TH limb loss and prosthesis use and disuse during gait may be compensation in the upper body, contributing to back pain or injury. Understanding the impact of not wearing a TH prosthesis on upper body asymmetries and spatial-temporal aspects of gait will inform how TH prosthesis use and disuse affects the body.

RESEARCH QUESTION

Does TH limb loss alter upper body asymmetries and spatial-temporal parameters during gait when wearing and not wearing a prosthesis compared to able-bodied controls?

METHODS

Eight male TH limb loss participants and eight male control participants completed three gait trials at self-selected speeds. The TH limb loss group performed trials with and without their prosthesis. Arm swing, trunk angular displacement, trunk-pelvis moment, and spatial-temporal aspects were compared using non-parametric statistical analyses.

RESULTS

Both TH walking conditions showed greater arm swing in the intact limb compared to the residual (p≤0.001), resulting in increased asymmetry compared to the control group (p≤0.001). Without the prosthesis, there was less trunk flexion and lateral flexion compared to the control group (p≤0.001). Maximum moments between the trunk and pelvis were higher in the TH group than the control group (p≤0.05). Spatial-temporal parameters of gait did not differ between the control group and either TH limb loss condition.

SIGNIFICANCE

Prosthesis use affects upper body kinematics and kinetics, but does not significantly impact spatial-temporal aspects of gait, suggesting these are compensatory actions. Wearing a prosthesis helps achieve more normative upper body kinematics and kinetics than not wearing a prosthesis, which may help limit back pain. These findings emphasize the importance of encouraging at least passive use of prostheses for individuals with TH limb loss.

Extended physiological proprioception is affected by transhumeral Socket-Suspended prosthesis use

The objective of this study was to define targeted reaching performance without visual information for transhumeral (TH) prosthesis users, establishing baseline information about extended physiological proprioception (EPP) in this population. Subjects completed a seated proprioceptive targeting task under simultaneous motion capture, using their prosthesis and intact limb. Eight male subjects, median age of 58 years (range 29-77 years), were selected from an ongoing screening study to participate. Five subjects had a left-side TH amputation, and three a right-side TH amputation. Median time since amputation was 9 years (range 3-54 years). Four subjects used a body-powered prosthetic hook, three a myoelectric hand, and one a myoelectric hook. The outcome measures were precision and accuracy, motion of the targeting hand, and joint angular displacement. Subjects demonstrated better precision when targeting with their intact limb compared to targeting with their prosthesis, 1.9 cm2 (0.8-3.0) v. 7.1 cm2 (1.3-12.8), respectively, p = 0.008. Subjects achieved a more direct reach path ratio when targeting with the intact limb compared to with the prosthesis, 1.2 (1.1-1.3) v. 1.3 (1.3-1.4), respectively, p = 0.039 The acceleration, deceleration, and corrective phase durations were consistent between conditions. Trunk angular displacement increased in flexion, lateral flexion, and axial rotation while shoulder flexion decreased when subjects targeted with their prosthesis compared to the intact limb. The differences in targeting precision, reach patio ratio, and joint angular displacements while completing the targeting task indicate diminished EPP. These findings establish baseline information about EPP in TH prosthesis users for comparison as novel prosthesis suspension systems become more available to be tested.

Strain-mode-specific mechanical testing and the interpretation of bone adaptation in the deer calcaneus

The artiodactyl (deer and sheep) calcaneus is a model that helps in understanding how many bones achieve anatomical optimization and functional adaptation. We consider how the dorsal and plantar cortices of these bones are optimized in quasi-isolation (the conventional view) versus in the context of load sharing along the calcaneal shaft by "tension members" (the plantar ligament and superficial digital flexor tendon). This load-sharing concept replaces the conventional view, as we have argued in a recent publication that employs an advanced analytical model of habitual loading and fracture risk factors of the deer calcaneus. Like deer and sheep calcanei, many mammalian limb bones also experience prevalent bending, which seems problematic because the bone is weaker and less fatigue-resistant in tension than compression. To understand how bones adapt to bending loads and counteract deleterious consequences of tension, it is important to examine both strain-mode-specific (S-M-S) testing (compression testing of bone habitually loaded in compression; tension testing of bone habitually loaded in tension) and non-S-M-S testing. Mechanical testing was performed on individually machined specimens from the dorsal "compression cortex" and plantar "tension cortex" of adult deer calcanei and were independently tested to failure in one of these two strain modes. We hypothesized that the mechanical properties of each cortex region would be optimized for its habitual strain mode when these regions are considered independently. Consistent with this hypothesis, energy absorption parameters were approximately three times greater in S-M-S compression testing in the dorsal/compression cortex when compared to non-S-M-S tension testing of the dorsal cortex. However, inconsistent with this hypothesis, S-M-S tension testing of the plantar/tension cortex did not show greater energy absorption compared to non-S-M-S compression testing of the plantar cortex. When compared to the dorsal cortex, the plantar cortex only had a higher elastic modulus (in S-M-S testing of both regions). Therefore, the greater strength and capacity for energy absorption of the dorsal cortex might "protect" the weaker plantar cortex during functional loading. However, this conventional interpretation (i.e., considering adaptation of each cortex in isolation) is rejected when critically considering the load-sharing influences of the ligament and tendon that course along the plantar cortex. This important finding/interpretation has general implications for a better understanding of how other similarly loaded bones achieve anatomical optimization and functional adaptation.

Exploration of the synergistic role of cortical thickness asymmetry ("Trabecular Eccentricity" concept) in reducing fracture risk in the human femoral neck and a control bone (Artiodactyl Calcaneus)

The mechanobiology of the human femoral neck is a focus of research for many reasons including studies that aim to curb age-related bone loss that contributes to a near-exponential rate of hip fractures. Many believe that the femoral neck is often loaded in rather simple bending, which causes net tension stress in the upper (superior) femoral neck and net compression stress in its inferior aspect ("T/C paradigm"). This T/C loading regime lacks in vivo proof. The "C/C paradigm" is a plausible alternative simplified load history that is characterized by a gradient of net compression across the entire femoral neck; action of the gluteus medius and external rotators of the hip are important in this context. It is unclear which paradigm is at play in natural loading due to lack of in vivo bone strain data and deficiencies in understanding mechanisms and manifestations of bone adaptation in tension vs. compression. For these reasons, studies of the femoral neck would benefit from being compared to a 'control bone' that has been proven, by strain data, to be habitually loaded in bending. The artiodactyl (sheep and deer) calcaneus model has been shown to be a very suitable control in this context. However, the application of this control in understanding the load history of the femoral neck has only been attempted in two prior studies, which did not examine the interplay between cortical and trabecular bone, or potential load-sharing influences of tendons and ligaments. Our first goal is to compare fracture risk factors of the femoral neck in both paradigms. Our second goal is to compare and contrast the deer calcaneus to the human femoral neck in terms of fracture risk factors in the T/C paradigm (the C/C paradigm is not applicable in the artiodactyl calcaneus due to its highly constrained loading). Our third goal explores interplay between dorsal/compression and plantar/tension regions of the deer calcaneus and the load-sharing roles of a nearby ligament and tendon, with insights for translation to the femoral neck. These goals were achieved by employing the analytical model of Fox and Keaveny (J. Theoretical Biology 2001, 2003) that estimates fracture risk factors of the femoral neck. This model focuses on biomechanical advantages of the asymmetric distribution of cortical bone in the direction of habitual loading. The cortical thickness asymmetry of the femoral neck (thin superior cortex, thick inferior cortex) reflects the superior-inferior placement of trabecular bone (i.e., "trabecular eccentricity," TE). TE helps the femoral neck adapt to typical stresses and strains through load-sharing between superior and inferior cortices. Our goals were evaluated in the context of TE. Results showed the C/C paradigm has lower risk factors for the superior cortex and for the overall femoral neck, which is clinically relevant. TE analyses of the deer calcaneus revealed important synergism in load-sharing between the plantar/tension cortex and adjacent ligament/tendon, which challenges conventional understanding of how this control bone achieves functional adaptation. Comparisons with the control bone also exposed important deficiencies in current understanding of human femoral neck loading and its potential histocompositional adaptations.

Fluorapatite-Coated Percutaneous Devices Promote Wound Healing and Limit Epithelial Downgrowth at the Skin-Device Interface

A percutaneous osseointegrated device becomes deeply ingrown by endosteal bone and traverses the overlying soft tissues of the residual limb, providing a direct link to the bone-anchored artificial limb. Continuous wound healing around these devices can result in the formation of sinus tracts as “down-growing” epithelial cells are unable to recognize and adhere to the “nonbiological” implant surface. Such sinus tracts provide paths for bacterial colonization and deep infection. In order to limit adverse outcomes and provide a robust seal, it was hypothesized that by coating the titanium surface of the percutaneous post with the mineral component of dental enamel, down-growing epidermal cells might recognize the coating as “biological” and adhere to this nonliving surface. To test this hypothesis, sintered partially and fully fluoridated hydroxyapatite (HA) was chosen as coatings. Using an established surgical protocol, fluorapatite (FA), hydroxyfluorapatite (FHA), HA-coated percutaneous posts, and titanium controls were surgically placed under the dorsal skin in 20 CD hairless rats. The animals were sacrificed at four weeks, and implants and surrounding tissues were harvested and subjected to further analyses. Downgrowth and granulation tissue area data showed statistically significant reductions around the FA-coated devices. Moreover, compared to the control group, the FA- and HA-coated groups showed downregulation of mRNA for EGFr, EGF, and FGF-10. Interestingly, the FA-coated group had upregulation of TGF-α. These data suggest that FA could become an ideal coating material for preventing downgrowth, assuming the long-term stability of these coated surfaces can be verified in a clinically relevant animal model.

Testing Precision and Accuracy of an Upper Extremity Proprioceptive Targeting Task Assessment

Objective

To develop and test an assessment measuring extended physiological proprioception (EPP). EPP is a learned skill that allows one to extend proprioception to an external tool, which is important for controlling prosthetic devices. The current study examines the ability of this assessment to measure EPP in a nonamputee population for translation into the affected population.

Design

Measuring precision and accuracy of an upper extremity (UE) proprioceptive targeting task assessment. Participants completed 2 sessions of a targeting task while seated at a table. The targeting was completed with the dominant and nondominant hand and with eyes open and eyes closed during the task. Participants completed 2 sessions of the clinical test with a 1-week washout period to simulate reasonable time between clinical visits.

Setting

Research laboratory.

Participants

Twenty right-handed participants (N=20) with no neurologic or orthopedic deficits that would interfere with proprioception, median age of 25 years (range, 19-33 years), completed the assessment (10 men, 10 women).

Interventions

Not applicable.

Main Outcome Measures

Precision (consistency in targeting) and accuracy (distance between the intended target and participant result) in UE targeting task using EPP; test-retest repeatability between sessions.

Results

Both precision and accuracy were significantly decreased in the eyes-closed condition compared with the eyes-open condition regardless of targeting with dominant or nondominant hand (all P<.001). In the eyes-open condition, there was a dominance effect relating to the accuracy; however, in the eyes-closed condition, accuracy between dominant and nondominant hands was statistically equivalent. Based on minimum detectable change with 95% confidence, there was no change in either metric between the first and second sessions.

Conclusions

The results of this study support the feasibility of using this assessment to measure EPP-based on the definition of EPP as a learned skill that indicates control over an external, simple tool-because they demonstrate reliance on proprioception in the eyes-closed condition, symmetry in proprioceptive accuracy between hands for within-participant control, and test-retest reliability for longitudinal measurements. The results also establish normative values for this assessment in young, healthy adults. Further research is required in a clinical population to evaluate the UE proprioceptive targeting task assessment further and collect objective data on EPP.

Clinical Basis for Creating an Osseointegrated Neural Interface

As technology continues to improve within the neuroprosthetic landscape, there has been a paradigm shift in the approach to amputation and surgical implementation of haptic neural prosthesis for limb restoration. The Osseointegrated Neural Interface (ONI) is a proposed solution involving the transposition of terminal nerves into the medullary canal of long bones. This design combines concepts of neuroma formation and prevention with osseointegration to provide a stable environment for conduction of neural signals for sophisticated prosthetic control. While this concept has previously been explored in animal models, it has yet to be explored in humans. This anatomic study used three upper limb and three lower limb cadavers to assess the clinical feasibility of creating an ONI in humans. Anatomical measurement of the major peripheral nerves- circumference, length, and depth- were performed as they are critical for electrode design and rerouting of the nerves into the long bones. CT imaging was used for morphologic bone evaluation and virtual implantation of two osseointegrated implants were performed to assess the amount of residual medullary space available for housing the neural interfacing hardware. Use of a small stem osseointegrated implant was found to reduce bone removal and provide more intramedullary space than a traditional implant; however, the higher the amputation site, the less medullary space was available regardless of implant type. Thus the stability of the endoprosthesis must be maximized while still maintaining enough residual space for the interface components. The results from this study provide an anatomic basis required for establishing a clinically applicable ONI in humans. They may serve as a guide for surgical implementation of an osseointegrated endoprosthesis with intramedullary electrodes for prosthetic control.

Finite Element Analysis of Transhumeral and Transtibial Percutaneous Osseointegrated Endoprosthesis Implantation

Cadaveric mechanical testing of a percutaneous osseointegration docking system (PODS) for osseointegration (OI) prosthetic limb attachment revealed that translation of the exact system from the humerus to the tibia may not be suitable. The PODS, designed specifically for the humerus achieved 1.4-4.8 times greater mechanical stability in the humerus than in the tibia despite morphology that indicated translational feasibility. To better understand this discrepancy, finite element analyses (FEAs) modeled the implantation of the PODS into the bones. Models from cadaveric humeri (n = 3) and tibia (n = 3) were constructed from CT scans, and virtual implantation preparation of an array of endoprosthesis sizes that made contact with the endosteal surface but did not penetrate the outer cortex was performed. Final impaction of the endoprosthesis was simulated using a displacement ramp function to press the endoprosthesis model into the bone. Impaction force and maximum first principal (circumferential) stress were recorded to estimate stability and assess fracture risk of the system. We hypothesized that the humerus and tibia would have different optimal PODS sizing criteria that maximized impaction force and minimized first principal stress. The optimal sizing for the humerus corresponded to implantation instructions, whereas for the tibia optimal sizing was three times larger than the guidelines indicated. This FEA examination of impaction force and stress distribution lead us to believe that the same endoprosthesis strategy for the humerus is not suitable for the tibia because of thin medial and lateral cortices that compromise implantation.

Virtual implantation technique to estimate endoprosthetic contact of percutaneous osseointegrated devices in the tibia

Percutaneous osseointegrated (OI) devices have an endoprosthesis attached to the residual bone of an amputated limb, then pass permanently through the skin to be connected to the distal prosthetic componentry outside of the body. Whether the bone-anchoring region of current OI endoprostheses are cylindrical, and/or conical, they require intimate bone-endoprosthesis contact to promote stabilizing bone attachment. However, removing too much cortical bone to achieve more contact leads to thinner and, subsequently, weaker cortical walls. Endoprostheses need to be designed to balance these factors, namely maximizing the contact, while minimizing the volume of bone removed. In this study, 27 human tibias were used to develop and validate a virtual implantation method. Then, 40 additional tibias were virtually implanted with mock cylindrical and conical bone-anchoring regions at seven residual limb lengths to measure resultant bone-endoprosthesis contact and bone removal. The ratio of bone-endoprosthesis contact to bone volume removed showed the conical geometry had more contact area per volume bone removed for all amputation levels (p ≤ 0.001). In both mock devices, cortical penetration of the endoprosthesis at 20% residual length occurred in 74% of cases evaluated, indicating that alternative endoprosthesis geometries may be needed for clinical success in that region of bone.

Replicating dynamic humerus motion using an industrial robot

Transhumeral percutaneous osseointegrated prostheses provide upper-extremity amputees with increased range of motion, more natural movement patterns, and enhanced proprioception. However, direct skeletal attachment of the endoprosthesis elevates the risk of bone fracture, which could necessitate revision surgery or result in loss of the residual limb. Bone fracture loads are direction dependent, strain rate dependent, and load rate dependent. Furthermore, in vivo, bone experiences multiaxial loading. Yet, mechanical characterization of the bone-implant interface is still performed with simple uni- or bi-axial loading scenarios that do not replicate the dynamic multiaxial loading environment inherent in human motion. The objective of this investigation was to reproduce the dynamic multiaxial loading conditions that the humerus experiences in vivo by robotically replicating humeral kinematics of advanced activities of daily living typical of an active amputee population. Specifically, 115 jumping jack, 105 jogging, 15 jug lift, and 15 internal rotation trials-previously recorded via skin-marker motion capture-were replicated on an industrial robot and the resulting humeral trajectories were verified using an optical tracking system. To achieve this goal, a computational pipeline that accepts a motion capture trajectory as input and outputs a motion program for an industrial robot was implemented, validated, and made accessible via public code repositories. The industrial manipulator utilized in this study was able to robotically replicate over 95% of the aforementioned trials to within the characteristic error present in skin-marker derived motion capture datasets. This investigation demonstrates the ability to robotically replicate human motion that recapitulates the inertial forces and moments of high-speed, multiaxial activities for biomechanical and orthopaedic investigations. It also establishes a library of robotically replicated motions that can be utilized in future studies to characterize the interaction of prosthetic devices with the skeletal system, and introduces a computational pipeline for expanding this motion library.

Upper extremity prosthetic selection influences loading of transhumeral osseointegrated systems

Percutaneous osseointegrated (OI) implants are increasingly viable as an alternative to socket suspension of prosthetic limbs. Upper extremity prostheses have also become more complex to better replicate hand and arm function and attempt to recreate pre-amputation functional levels. With more functionality comes heavier devices that put more stress on the bone-implant interface, which could be an issue for implant stability. This study quantified transhumeral loading at defined amputation levels using four simulated prosthetic limb-types: (1) body powered hook, (2) myoelectric hook, (3) myoelectric hand, and (4) advanced prosthetic limb. Computational models were constructed to replicate the weight distribution of each prosthesis type, then applied to motion capture data collected during Advanced Activities of Daily Living (AADLs). For activities that did not include a handheld weight, the body powered prosthesis bending moments were 13–33% (range of means for each activity across amputation levels) of the intact arm moments (reference 100%), torsional moments were 12–15%, and axial pullout forces were 30–40% of the intact case (p≤0.001). The myoelectric hook and hand bending moments were 60–99%, torsional moments were 44–97%, and axial pullout forces were 62–101% of the intact case. The advanced prosthesis bending moments were 177–201%, torsional moments were 164–326%, and axial pullout forces were 133–185% of the intact case (p≤0.001). The addition of a handheld weight for briefcase carry and jug lift activities reduced the overall impact of the prosthetic model itself, where the body powered forces and moments were much closer to those of the intact model, and more complex prostheses further increased forces and moments beyond the intact arm levels. These results reveal a ranked order in loading magnitude according to complexity of the prosthetic device, and highlight the importance of considering the patient’s desired terminal device when planning post-operative percutaneous OI rehabilitation and training.

Cortical and medullary morphology of the tibia

Bone resorption caused by stress shielding and insufficient bone-implant contact continues to be problematic for orthopedic endoprostheses that utilize osseointegration (OI) for skeletal fixation. Morphologic analyses have helped combat this issue by defining anatomic parameters to optimize endoprosthesis loading by maximizing bone-implant contact. These studies have not typically included diaphyseal medullary morphology, as this region is not pertinent to total joint replacement. To the contrary, percutaneous OI endoprostheses for prosthetic limb attachment are placed in the diaphysis of the long bone. This study examined the cortical and medullary morphology of 116 fresh-frozen human cadaveric tibia using computed tomography. Anatomic landmarks were selected and custom MATLAB scripts were used to analyze the cross-sectional cortical and medullary morphology normalized to biomechanical length (BML). BML measured the distance between the tibial plateau and the tibial plafond. Properties such as cortical thickness, medullary diameter, and circularity of the medullary canal were quantified. We tested the influence of sex and laterality on morphology, and examined variations along the length of the bone. Results showed that while both sex and laterality impacted the location of anatomic landmarks, only sex influenced cross-sectional morphology. Overall, morphology significantly affected shape along the length of the bone for all examined properties except medullary circularity. This analysis found that distal to 35% BML, the canal is conducive to a circular implant, with medullary diameter ranging from 13 to 32 mm between 20 and 80% BML. A large size range is necessary for sufficient implant contact in order to accommodate residual limb length after amputation.

Restabilization of the Occipitocervical Junction After a Complete Unilateral Condylectomy: A Biomechanical Comparison of Unilateral and Bilateral Fixation Techniques

BACKGROUND

Occipitocervical instability may result from transcondylar resection of the occipital condyle. Initially, patients may be able to maintain a neutral alignment but severe occipitoatlantal subluxation may subsequently occur, with cranial settling, spinal cord kinking, and neurological injury.

OBJECTIVE

To evaluate the ability of posterior fixation constructs to prevent progression to severe deformity after radical unilateral condylectomy.

METHODS

Eight human cadaveric specimens (Oc-C2) underwent biomechanical testing to compare stiffness under physiological loads (1.5 N m). A complete unilateral condylectomy was performed to destabilize one Oc-C1 joint, and the contralateral joint was left intact. Unilateral Oc-C1 or Oc-C2 constructs on the resected side and bilateral Oc-C1 or Oc-C2 constructs were tested.

RESULTS

The bilateral Oc-C2 construct provided the greatest stiffness, but the difference was only statistically significant in certain planes of motion. The unilateral constructs had similar stiffness in lateral bending, but the unilateral Oc-C1 construct was less stiff in axial rotation and flexion-extension than the unilateral Oc-C2 construct. The bilateral Oc-C2 construct was stiffer than the unilateral Oc-C2 construct in axial rotation and lateral bending, but there was no difference between these constructs in flexion-extension.

CONCLUSION

Patients who undergo a complete unilateral condylectomy require close surveillance for occipitocervical instability. A bilateral Oc-C2 construct provides suitable biomechanical strength, which is superior to other constructs. A unilateral construct decreases abnormal motion but lacks the stiffness of a bilateral construct. However, given that most patients undergo a partial condylectomy and only a small proportion of patients develop instability, there may be scenarios in which a unilateral construct may be appropriate, such as for temporary internal stabilization.

Estimated forces and moments experienced by osseointegrated endoprostheses for lower extremity amputees

BACKGROUND

Percutaneous osseointegrated (OI) docking of prosthetic limbs returns loading directly to the residual bone of individuals with amputations. Lower limb diaphyseal biomechanics have not been studied during the wide range of daily activities performed by individuals with lower extremity amputations; therefore, little is known about the loads experienced at the bone-endoprosthetic interface of a percutaneous OI device.

RESEARCH QUESTION

Does residual limb length and/or gender influence loading magnitudes in the diaphysis of the femur or tibia during daily activities?

METHODS

This observational study used motion capture data from 40 non-amputee volunteers performing nine activities ranging from low to high demand, to virtually simulate residual limbs of amputees. To simulate diaphyseal bone loading in individuals with lower limb amputations, virtual joints were defined during post-processing at 25, 50, and 75 % of residual limb length of both the femur and the tibia, representing six clinically relevant residual limb lengths for OI device placement. Peak axial distractive and compressive forces, torsional moments, and bending moments were calculated for each activity. Comparisons were made between genders and between different levels of the simulated residual limb.

RESULTS

For simulated above and below knee amputations, short residual limbs showed the highest average bending, torsion, and axial distractive loads, while axial compressive loads were highest for long residual limbs. Absolute maxima for all subjects showed this same trend, except in below knee torsion, where 75 % residual tibia length showed the maximum. The highest demand activities yielding peaks in all directions were cutting with right leg planted, jump, run, and fall.

SIGNIFICANCE

Overall, individuals with shorter residual limbs experienced higher diaphyseal forces. This should be taken into consideration during surgical implantation of percutaneous OI devices where residual limb length can potentially be shortened, and during rehabilitation of percutaneous OI patients.

Evaluation of soft-tissue response around laser microgrooved titanium percutaneous devices

Percutaneous devices are prone to epidermal downgrowth and sinus tract formation, which can serve as a nidus for bacterial colonization and increase the risk of peri-prosthetic infection. A laser microgrooved topography has been shown to limit gingival epidermal downgrowth around dental implants. However, the efficacy of this laser microgrooved topography to limit epidermal downgrowth around nongingival percutaneous devices is yet to be investigated. In this study, devices with a porous-coated subdermal component and a percutaneous post were designed and manufactured. The proximal 2 mm section of the percutaneous post were left smooth, or were textured with either a porous coating, or with the laser microgrooved topography. The smooth and porous topographies served as controls. The devices were tested in a hairless guinea pig back model, where 18 animals were randomly assigned into three groups, with each group receiving one implant type (n = 6/group). Four weeks postimplantation, the devices with surrounding soft-tissues were harvested and processed for histological analyses. Results indicated that the laser microgrooved topography failed to prevent epidermal downgrowth (23 ± 4%) around percutaneous posts in this model. Furthermore, no significant differences (p = 0.70) in epidermal downgrowth were present between the three topographies, with all the groups exhibiting similar measures of downgrowth. Overall, these findings suggest that the laser microgrooved topography may not halt downgrowth around percutaneous devices for dermal applications.

Variation in bone response to the placement of percutaneous osseointegrated endoprostheses: A 24-month follow-up in sheep

Percutaneous osseointegrated (OI) devices for amputees are metallic endoprostheses, that are surgically implanted into the residual stump bone and protrude through the skin, allowing attachment of an exoprosthetic limb. In contrast to standard socket suspension systems, these percutaneous OI devices provide superior attachment platforms for artificial limbs. However, bone adaptation, which includes atrophy and/or hypertrophy along the extent of the host bone-endoprosthetic interface, is seen clinically and depends upon where along the bone the device ultimately transfers loading forces to the skeletal system. The goal of this study was to determine if a percutaneous OI device, designed with a porous coated distal region and an end-loading collar, could promote and maintain stable bone attachment. A total of eight, 18 to 24-month old, mixed-breed sheep were surgically implanted with a percutaneous OI device. For 24-months, the animals were allowed to bear weight as tolerated and were monitored for signs of bone remodelling. At necropsy, the endoprosthesis and the surrounding tissues were harvested, radiographically imaged, and histomorphometrically analyzed to determine the periprosthetic bone adaptation in five animals. Bone growth into the porous coating was achieved in all five animals. Serial radiographic data showed stress-shielding related bone adaptation occurs based on the placement of the endoprosthetic stem. When collar placement and achieved end-bearing against the transected bone, distal bone conservation/hypertrophy was observed. The results supported the use of a distally loading and distally porous coated percutaneous OI device to achieve distal host bone maintenance.

Biomimetic coatings and negative pressure wound therapy independently limit epithelial downgrowth around percutaneous devices

Biomimetic material coatings and negative pressure wound therapy (NPWT) have been shown independently to limit the epithelial downgrowth rates in percutaneous devices. It was therefore hypothesized that these techniques, in combination, could further limit the clinically observed epithelial downgrowth around these devices. In this study, we evaluated the efficacy of two biomimetic coatings, collagen and hydroxyapatite (HA), to prevent downgrowth when used with continuous NPWT. Using an established single-stage surgical protocol, collagen (n = 10) and HA (n = 10) coated devices were implanted subdermally on the back of hairless guinea pigs. Five animals from each group were subjected to continuous ~90 mmHg NPWT. Four weeks post-implantation, animals were sacrificed, and the devices and surrounding tissues were harvested, processed, and downgrowth was computed and compared to historical porous titanium coated controls. Data showed a significant reduction in downgrowth in NPWT treated animals (p ≤ 0.05) when compared to the untreated porous titanium controls. HA coated devices, without the NPWT treatment, also showed significantly decreased downgrowth compared to the untreated porous titanium controls.

Epidermal growth factor receptor genes are overexpressed within the periprosthetic soft-tissue around percutaneous devices: A pilot study

Epidermal downgrowth around percutaneous devices produce sinus tracts, which then accumulate bacteria becoming foci of infection. This mode to failure is epidermal-centric, and is accelerated by changes in the chemokines and cytokines of the underlying periprosthetic granulation tissue (GT). In order to more fully comprehend the mechanism of downgrowth, in this 28-day study, percutaneous devices were placed in 10 Zucker diabetic fatty rats; 5 animals were induced with diabetes mellitus II (DM II) prior to the surgery and 5 animals served as a healthy, nondiabetic cohort. At necropsy, periprosthetic tissues were harvested, and underwent histological and polymerase chain reaction (PCR) studies. After isolating GTs from the surrounding tissue and extracting ribonucleic acids, PCR array and quantitative-PCR (qPCR) analyses were carried-out. The PCR array for 84 key wound-healing associated genes showed a five-fold or greater change in 31 genes in the GTs of healthy animals compared to uninjured healthy typical skin tissues. Eighteen genes were overexpressed and these included epidermal growth factor (EGF) and epidermal growth factor receptor (EGFR). Thirteen genes were underexpressed. When GTs of DM II animals were compared to healthy animals, there were 8 genes overexpressed and 25 genes underexpressed; under expressed genes included EGF and EGFR. The qPCR and immunohistochemistry data further validated these observations. Pathway analysis of genes up-regulated 15-fold or more indicated two, EGFR and interleukin-10, centric clustering effects. It was concluded that EGFR could be a key player in exacerbating the epidermal downgrowth, and might be an effective target for preventing downgrowth.

Sex and Laterality Differences in Medullary Humerus Morphology

Percutaneous osseointegrated (OI) prosthetic limb attachment holds promise for transhumeral amputees. Understanding humeral medullary morphology is necessary for informed design of upper extremity OI systems, and is beneficial to the field of megaprosthetic reconstruction of the distal humerus where diaphyseal fixation is desired. The purpose of this study was to quantify the sex and laterality differences in humerus morphology, specifically over the diaphysis. Three‐dimensional surface reconstructions of 58 pairs of cadaveric humeri (43 male, 15 female) were generated from CT data. Measures describing periosteal and medullary morphology were collected relative to an anatomic coordinate system. Sex and laterality differences in biomechanical length (BML) were observed (P ≤ 0.001 and 0.022, respectively). Head radius was larger in males than females (P ≤ 0.001). Retroversion was increased in right humeri relative to left (P ≤ 0.001). Canal orientation exhibited a conformational shift from anteversion to retroversion distally at approximately 65% BML. Right humeri exhibited larger medullary diameters than left in the 1st and 2nd principal directions (P ≤ 0.024). Males displayed larger diameter medullary canals proximally (P ≤ 0.029) and an increased rate of divergence of the endosteal cortex in the proximal diaphysis (P ≤ 0.009). Females exhibited higher canal aspect ratios at mid‐shaft (P ≤ 0.014) and lower mean cortical thickness (P ≤ 0.001). Human humeral diaphysis morphology exhibits sex and laterality differences, which are dependent on position along the diaphysis. Understanding humeral morphology is necessary to achieve adequate primary stability and bone apposition in design of endoprosthetic stems for percutaneous OI implants, and distal humerus replacement. Anat Rec, 302:1709–1717, 2019. © 2019 The Authors. The Anatomical Record published by Wiley Periodicals, Inc. on behalf of American Association for Anatomy

Influence of negative pressure wound therapy on peri-prosthetic tissue vascularization and inflammation around porous titanium percutaneous devices

Negative Pressure Wound Therapy (NPWT) has been shown to limit downgrowth around percutaneous devices in a guinea pig model. However, the influence of NPWT on peri-prosthetic tissue characteristics leading to limited downgrowth is still unclear. In order to investigate this, 12 CD hairless rats were assigned into two groups, NPWT and Untreated (n = 6/group). Each animal was implanted with a porous coated titanium percutaneous device and was dressed with a gauze and semi-occlusive base dressing. Post-surgery, animals in the NPWT Group received a regimen of NPWT treatment (-70 to -90 mmHg). After 4 weeks, tissue was collected over the device and stained with CD31 and CD68 to quantify blood vessel density and inflammation, respectively. The device with the surrounding tissue was also collected to quantify downgrowth. NPWT treatment led to a 1.6-fold increase in blood vessel densities compared to untreated tissues (p < 0.05). NPWT treatment also resulted in half the downgrowth as the Untreated Group, although not statistically significant (p = 0.19). Additionally, the results showed a trend toward increased CD68 cell densities in the NPWT Group compared to the Untreated Group (p = 0.09). These findings suggest that NPWT may influence wound healing responses in percutaneous devices by increasing blood vessel densities, limiting downgrowth and potentially increasing inflammation. Overall, NPWT may enhance tissue vascularity around percutaneous devices, especially in patients with impaired wound healing. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 2091-2101, 2019.

The Circle-Fit Method Helps Make Reliable Cortical Thickness Measurements Regardless of Humeral Length

Background

Although proximal humerus strength/quality can be assessed using cortical thickness measurements (eg, cortical index), there is no agreement where to make them. Tingart and coworkers used measurements where the proximal endosteum becomes parallel, while Mather and coworkers used measurements where the periosteum becomes parallel. The new circle-fit method (CFM) makes 2 metaphyseal (M1-M2) and 6 diaphyseal (D1-D6) measurements referenced from humeral head diameter (HHD). However, it is unknown whether these locations correlate to humeral length (HL). Accordingly, we asked: (1) Does HHD, Tingart distance, and Mather distance correlate with HL? (2) What is the location of HHD, Tingart distance, and Mather distance as a percentage of HL? and (3) Which CFM D1-D6 locations correlate with Tingart and Mather distances?

Materials and Methods

Measurements made on cortical thickness (CT) scout views of 19 humeri (ages: 16-73 years) included HHD, distances from the superior aspect of the humerus to proximal Tingart and Mather locations, and HL.

Results

Intraclass correlation was excellent for CFM-HHD, poor for Tingart, and moderate for Mather. The CFM-HHD had a stronger correlation to HL than Tingart and Mather. Mean HHD was 15.5% (0.9%) of HL while Tingart was 27.0% (4.1%) and Mather was 23.2% (3.8%). Tingart distance corresponded to D2/D3 CFM locations while the Mather distance was similar to D1/D2.

Discussion

The CFM reliably correlates with HL and provides a stronger correlation and less variance between specimens than the Tingart or Mather Methods.

Conclusions

Because the CFM produces reliable percent of HL locations, it should be used to define locations for obtaining biomechanically relevant CT measurements such as cortical index. Stronger correlations of these CFM-based measurements with proximal humerus strength will be important for developing advanced algorithms for fracture treatment.

Advancing the deer calcaneus model for bone adaptation studies: ex vivo strains obtained after transecting the tension members suggest an unrecognized important role for shear strains

Sheep and deer calcanei are finding increased use as models for studies of bone adaptation, including advancing understanding of how the strain (deformation) environment influences the ontogenetic emergence of biomechanically relevant structural and material variations in cortical and trabecular bone. These artiodactyl calcanei seem ideal for these analyses because they function like simply loaded short-cantilevered beams with net compression and tension strains on the dorsal and plantar cortices, respectively. However, this habitual strain distribution requires more rigorous validation because it has been shown by limited in vivo and ex vivo strain measurements obtained during controlled ambulation (typically walking and trotting). The conception that these calcanei are relatively simply and habitually loaded 'tension/compression bones' could be invalid if infrequent, though biologically relevant, loads substantially change the location of the neutral axis (NA) that separates 'compression' and 'tension' regions. The effect on calcaneus strains of the tension members (plantar ligament and flexor tendon) is also not well understood and measuring strains after transecting them could reveal that they significantly modulate the strain distribution. We tested the hypothesis that the NA location previously described during simulated on-axis loads of deer calcanei would exhibit limited variations even when load perturbations are unusual (e.g. off-axis loads) or extreme (e.g. after transection of the tension members). We also examined regional differences in the predominance of the three strain modes (tension, compression, and shear) in these various load conditions in dorsal, plantar, medial, and lateral cortices. In addition to considering principal strains (tension and compression) and maximum shear strains, we also considered material-axis (M-A) shear strains. M-A shear strains are those that are aligned along the long axis of the bone and are considered to have greater biomechanical relevance than maximum shear strains because failure theories of composite materials and bone are often based on stresses or strains in the principal material directions. We used the same load apparatus from our prior study of mule deer calcanei. Results showed that although the NA rotated up to 8° medially and 15° laterally during these off-axis loads, it did not shift dramatically until after transection of all tension members. When comparing results based on maximum shear strain data vs. M-A shear strain data, the dominant strain mode changed only in the plantar cortex - as expected (in accordance with our a priori view) it was tension when M-A shear strains were considered (shear : tension = 0.2) but changed to dominant shear when maximum shear strain data were considered (shear : tension = 1.3). This difference leads to different conclusions and speculations regarding which specific strain modes and magnitudes most strongly influence the emergence of the marked mineralization and histomorphological differences in the dorsal vs. plantar cortices. Consequently, our prior simplification of the deer calcaneus model as a simply loaded 'tension/compression bone' (i.e. plantar/dorsal) might be incorrect. In vivo and in finite element analyses are needed to determine whether describing it as a 'shear-tension/compression' bone is more accurate. Addressing this question will help to advance the artiodactyl calcaneus as an experimental model for bone adaptation studies.

Peri-prosthetic tissue reaction to discontinuation of negative pressure wound therapy around porous titanium percutaneous devices

Negative pressure wound therapy (NPWT) has been reported to limit epithelial downgrowth, one of the failure mechanisms of percutaneous devices. In a previous study, when NPWT was applied for 4 weeks (NPWT Group) to porous coated titanium percutaneous devices, downgrowth (5 ± 4%; mean ± one SD) was significantly reduced compared to untreated controls (Untreated Group) (16 ± 6%; p ≤ 0.01). However, it was unclear whether this beneficial effect was sustained when NPWT was discontinued. In order to test this, porous coated titanium percutaneous devices were implanted into 6 hairless guinea pigs. Post-surgery, animals received 4 weeks of NPWT treatment followed by 4 weeks of no treatment (Discontinued Group). At necropsy, the devices and surrounding tissues were harvested and processed. Quantitative downgrowth measurements and qualitative analyses of tissue characteristics were performed, and compared to historical controls (NPWT and Untreated Groups). The Discontinued Group, at 8 weeks, had significantly more downgrowth than the NPWT Group at 4 weeks (23 ± 3% vs. 5 ± 4%; p ≤ 0.01). At 8 weeks, the Discontinued Group qualitatively appeared to exhibit reduced numbers of blood vessels and increased degree of fibrosis compared to the NPWT Group at 4 weeks. This study suggests that NPWT will only be an effective treatment for limiting downgrowth if used continuously. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2018. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 564-572, 2019.

Transhumeral loading during advanced upper extremity activities of daily living

Percutaneous osseointegrated (OI) implants for direct skeletal attachment of upper extremity prosthetics represent an alternative to traditional socket suspension that may yield improved patient function and satisfaction. This is especially true in high-level, transhumeral amputees where prosthetic fitting is challenging and abandonment rates remain high. However, maintaining mechanical integrity of the bone-implant interface is crucial for safe clinical introduction of this technology. The collection of population data on the transhumeral loading environment will aid in the design of compliance and overload protection devices that mitigate the risk of periprosthetic fracture. We collected marker-based upper extremity kinematic data from non-amputee volunteers during advanced activities of daily living (AADLs) that applied dynamic loading to the humerus. Inverse dynamic analysis was applied to calculate the axial force, bending and torsional moments at three virtual amputation levels representing 25, 50, and 75% residual humeral length. The influences of amputation level, elbow flexion constraint, gender and anthropometric scaling were assessed. Results indicate that the proximal (25%) amputation level experienced significantly higher axial forces and bending moments across all subjects when compared to distal amputation levels (p≤0.030). Constraining elbow flexion had a limited influence on peak transhumeral loads. Male subjects experienced higher axial forces during all evaluated activities (p≤0.023). Peak axial force for all activities occurred during jumping jacks (174.5N). Peak bending (57.6Nm) and torsional (57.2Nm) moments occurred during jumping jacks and rapid internal humeral rotation, respectively. Calculated loads fall within the range of implant fixation failure loads reported in cadaveric investigations of humeral stem fixation; indicating that periprosthetic fracture may occur during non-contact AADLs. These kinematic data, collected over a range of AADLs, will aid in the development of overload protection devices and appropriate post-operative rehabilitation protocols that balance return to an active lifestyle with patient safety.

A 24-month evaluation of a percutaneous osseointegrated limb-skin interface in an ovine amputation model

Percutaneous osseointegrated (OI) prostheses directly connect an artificial limb to the residual appendicular skeleton via a permanently implanted endoprosthesis with a bridging connector that protrudes through the skin. The resulting stoma produces unique medical and biological challenges. Previously, a study using a large animal amputation model indicated that infection could be largely prevented, for at least a 12-month period, but the terminal epithelium continued to downgrow. The current study was undertaken to test the longer-term efficacy of this implant construct to maintain a stable skin-implant interface for 24 months. Using the previously successful amputation and implantation surgical procedure, a total of eight sheep were fitted with a percutaneous OI prosthesis. Two animals were removed from the study due to early complications. Of the remaining six sheep, one (16.7%) became infected at 15-months post-implantation and five remained infection-free for the intended 24 months. The histological data of the remaining animals further confirmed the grossly observable epithelial downgrowth. Albeit a receding interface, it was clear that all animals that survived to the end of the study had residual fibrous soft-tissue ingrowth into, and debris within, the exposed titanium porous-coated surface. Overall, the data demonstrated that the porous coated subdermal barrier offered initial protection against infection. However, the fibrous skin attachment was continuously lysed over time by the down-growing epithelium.

Arthroscopic Talar Dome Access Using a Standard Versus Wire-Based Traction Method for Ankle Joint Distraction

PURPOSE

To evaluate the accessibility of the talar dome through anterior and posterior portals for ankle arthroscopy with the standard noninvasive distraction versus wire-based longitudinal distraction using a tensioned wire placed transversely through the calcaneal tuberosity.

METHODS

Seven matched pairs of thigh-to-foot specimens underwent ankle arthroscopy with 1 of 2 methods of distraction: a standard noninvasive strapping technique or a calcaneal tuberosity wire-based technique. The order of the arthroscopic approach and use of a distraction method was randomly determined. The areas accessed from both 2-portal anterior and 2-portal posterior approaches were determined by using a molded translucent grid.

RESULTS

The mean talar surface accessible by anterior ankle arthroscopy was comparable with noninvasive versus calcaneal wire distraction with 57.8% ± 17.2% (range, 32.9% to 75.7%) versus 61.5% ± 15.2% (range, 38.5% to 79.1%) of the talar dome, respectively (P = .590). The use of calcaneal wire distraction significantly improved posterior talar dome accessibility compared with noninvasive distraction, with 56.4% ± 20.0% (range, 14.4% to 78.0%) versus 39.8% ± 14.9% (range, 20.0% to 57.6%) of the talar dome, respectively (P = .031).

CONCLUSIONS

Under the conditions studied, our cadaveric model showed equivalent talar dome access with 2-portal anterior arthroscopy of calcaneal wire-based distraction versus noninvasive strap distraction, but improved access for 2-portal posterior arthroscopy with calcaneal wire-based distraction versus noninvasive strap distraction.

CLINICAL RELEVANCE

The posterior 40% of the talar dome is difficult to access via anterior ankle arthroscopy. Posterior calcaneal tuberosity wire-based longitudinal distraction improved arthroscopic access to the centro-posterior talar dome with a posterior arthroscopic approach.

Negative pressure wound therapy limits downgrowth in percutaneous devices

Maintenance of a soft tissue seal around percutaneous devices is challenged by the downgrowth of periprosthetic tissues-a gateway to potential infection. As negative pressure wound therapy (NPWT) is used clinically to facilitate healing of complex soft tissue pathologies, it was hypothesized that NPWT could limit downgrowth of periprosthetic tissues. To test this hypothesis, 20 hairless guinea pigs were randomly assigned into four groups (n = 5/group). Using a One-Stage (Groups 1 and 3) or a Two-Stage (Groups 2 and 4) surgical procedure, each animal was implanted with a titanium-alloy subdermal device porous-coated with commercially pure, medical grade titanium. Each subdermal device had a smooth titanium-alloy percutaneous post. The One-Stage procedure encompassed insertion of a fully assembled device during a single surgery. The Two-Stage procedure involved the implantation of a subdermal device during the first surgery, and then three weeks later, insertion of a percutaneous post. Groups 1 and 2 served as untreated controls and Groups 3 and 4 received NPWT. Four weeks postimplantation of the post, the devices and surrounding tissues were harvested, and histologically evaluated for downgrowth. Within the untreated control groups, the Two-Stage surgical procedure significantly decreased downgrowth (p = 0.027) when compared with the One-Stage procedure. Independent of the surgical procedures performed, NPWT significantly limited downgrowth (p ≤ 0.05) when compared with the untreated controls.

Deep transverse metatarsal ligament and static stability of lesser metatarsophalangeal joints: a cadaveric study

BACKGROUND

The static support that guides motion around the lesser metatarsophalangeal joints (MTPJs) is complex. Biomechanical studies revealed important roles of both the plantar plane and collateral ligaments. Since part of the plantar plate is attached to the deep transverse metatarsal ligament (DTML), we hypothesized that the transection of the DTML in the intermetatarsal space may substantially reduce the MTPJ stability.

METHODS

The second, third, and fourth MTPJ stabilities of 6 fresh-frozen human cadaveric foot specimens were measured under load control. Both dorsiflexion and dorsal subluxation conditions were tested. After the intact condition was assessed, the DTML was sequentially transected such that each MTPJ had a unilateral and then a bilateral DTML transection. Stiffness data were calculated using the loading range in each test condition. Paired Student t tests were performed to test for statistical significance (P value less than .05).

RESULTS

In intact specimens, the mean stiffness with dorsiflexion of the second, third, and fourth toes was 0.52 ± 0.15 N/deg. When the DTML was operatively transected on one side, the dorsiflexion stiffness significantly decreased 17.3% to an average of 0.43 ± 1.00 N/deg (P < .001). Subsequent transection of the DTML on the other side of each joint resulted in a further significant decrease of 5.8% to an average of 0.40 ± 0.08 N/deg (P < .001). The mean stiffness with dorsal subluxation of the intact second, third, and fourth toes was 3.55 ± 0.66 N/mm. When the DTML was operatively transected on one side, the dorsal subluxation stiffness significantly decreased 16.1% to an average of 2.98 ± 0.64 N/mm (P < .001). Subsequent transection of the DTML on the other side of each joint resulted in a further significance decrease of 7.6% to an average of 2.71 ± 0.48 N/mm (P = .016).

CONCLUSION

The DTML has a significant role in maintaining lesser MTPJ ligament stability. Both unilateral and bilateral DTML transections caused substantial instability of the lesser MTPJ.

CLINICAL RELEVANCE

The DTML is part of the natural static restraint to dorsiflexion or dorsal subluxation of the lesser MTPJ. Operative transection, injury, or degeneration of this ligament may predispose the adjacent MTPJ to instability.

Cortical screws used to rescue failed lumbar pedicle screw construct: a biomechanical analysis

OBJECT

Cortical trajectory screw constructs, developed as an alternative to pedicle screw fixation for the lumbar spine, have similar in vitro biomechanics. The possibility of one screw path having the ability to rescue the other in a revision scenario holds promise but has not been evaluated. The objective in this study was to investigate the biomechanical properties of traditional pedicle screws and cortical trajectory screws when each was used to rescue the other in the setting of revision.

METHODS

Ten fresh-frozen human lumbar spines were instrumented at L3-4, 5 with cortical trajectory screws and 5 with pedicle screws. Construct stiffness was recorded in flexion/extension, lateral bending, and axial rotation. The L-3 screw pullout strength was tested to failure for each specimen and salvaged with screws of the opposite trajectory. Mechanical stiffness was again recorded. The hybrid rescue trajectory screws at L-3 were then tested to failure.

RESULTS

Cortical screws, when used in a rescue construct, provided stiffness in flexion/extension and axial rotation similar to that provided by the initial pedicle screw construct prior to failure. The rescue pedicle screws provided stiffness similar to that provided by the primary cortical screw construct in flexion/extension, lateral bending, and axial rotation. In pullout testing, cortical rescue screws retained 60% of the original pedicle screw pullout strength, whereas pedicle rescue screws retained 65% of the original cortical screw pullout strength.

CONCLUSIONS

Cortical trajectory screws, previously studied as a primary mode of fixation, may also be used as a rescue option in the setting of a failed or compromised pedicle screw construct in the lumbar spine. Likewise, a standard pedicle screw construct may rescue a compromised cortical screw track. Cortical and pedicle screws each retain adequate construct stiffness and pullout strength when used for revision at the same level.

Progression of bone ingrowth and attachment strength for stability of percutaneous osseointegrated prostheses

BACKGROUND

Percutaneous osseointegrated prosthetic (POP) devices have been used clinically in Europe for decades. Unfortunately, their introduction into the United States has been delayed, in part due to the lack of data documenting the progression of osseointegration and mechanical stability.

QUESTIONS/PURPOSES

We determined the progression of bone ingrowth into porous-coated POP devices and established the interrelationship with mechanical stability.

METHODS

After amputation, 64 skeletally mature sheep received a custom porous-coated POP device and were then randomized into five time groups, with subsequent measurement of percentage of bone ingrowth into the available pore spaces (n = 32) and the mechanical pullout force (n = 32).

RESULTS

Postimplantation, there was an accelerated progression of bone ingrowth (~48% from 0 to 3 months) producing a mean pullout force of 5066 ± 1543 N. Subsequently, there was a slower but continued progression of bone ingrowth (~23% from 3 to 12 months) culminating with a mean pullout force of 13,485 ± 1855 N at 12 months postimplantation. There was a high linear correlation (R = 0.94) between the bone ingrowth and mechanical pullout stability.

CONCLUSIONS

This weightbearing model shows an accelerated progression of bone ingrowth into the porous coating; the amount of ingrowth observed at 3 months after surgery within the porous-coated POP devices was sufficient to generate mechanical stability.

CLINICAL RELEVANCE

The data document progression of bone ingrowth into porous-coated POP devices and establish a strong interrelationship between ingrowth and pullout strength. Further human data are needed to validate these findings.

A novel vacuum assisted closure therapy model for use with percutaneous devices

Long-term maintenance of a dermal barrier around a percutaneous prosthetic device remains a common clinical problem. A technique known as Negative Pressure Wound Therapy (NPWT) uses negative pressure to facilitate healing of impaired and complex soft tissue wounds. However, the combination of using negative pressure with percutaneous prosthetic devices has not been investigated. The goal of this study was to develop a methodology to apply negative pressure to the tissues surrounding a percutaneous device in an animal model; no tissue healing outcomes are presented. Specifically, four hairless rats received percutaneous porous coated titanium devices implanted on the dorsum and were bandaged with a semi occlusive film dressing. Two of these animals received NPWT; two animals received no NPWT and served as baseline controls. Over a 28-day period, both the number of dressing changes required between the two groups as well as the pressures were monitored. Negative pressures were successfully applied to the periprosthetic tissues in a clinically relevant range with a manageable number of dressing changes. This study provides a method for establishing, maintaining, and quantifying controlled negative pressures to the tissues surrounding percutaneous devices using a small animal model.

Comparison of in vitro techniques to controllably decrease bone mineral density of cancellous bone for biomechanical compressive testing

It is not surprising that an orthopedic device used with poorly mineralized bone can have lower mechanical fixation strength than the same device with well-mineralized bone. As new devices are being designed and tested, it is important to develop a controllable technique to decrease the bone mineral density of bone in vitro, so the fixation strength of the devices can be better modeled. Several different bone demineralization techniques have been established, but some use caustic chemicals and comparisons of their rates of demineralization have not been performed. In this study, a total of 120 cancellous bone cores were excised from ovine vertebra, scanned using a pico dual energy X-ray absorptiometry system to determine bone mineral density, then placed into one of five solutions (0.9% saline, 0.5M hydrochloric acid, 0.5M ethylenediaminetetraacetic acid, 0.5M formic acid, and 5% acetic acid). For each solution, 12 time periods ranging from 0 to 144h were investigated. After demineralization, all cores were rescanned and biomechanically loaded in compression to failure. Based on the rate of demineralization, the ease of use, the availability, and the correlation with the compressive bone strength, it was determined that the 5% acetic acid was the optimal demineralization solution to controllably decrease the bone mineral density of cancellous bone.

Role of plantar plate and surgical reconstruction techniques on static stability of lesser metatarsophalangeal joints: a biomechanical study

BACKGROUND

Disruption of the plantar plate of the lesser metatarsophalangeal (MTP) joints leads to significant instability. Despite the fact that plantar plate disorders are common, the best mode of treatment remains controversial with operative treatments having variable and somewhat unpredictable clinical outcomes.

METHODS

Lesser MTP joints from the second, third, and fourth toes from fresh-frozen cadaver feet were biomechanically tested: (1) intact, (2) with the plantar plate disrupted, and (3) following a Weil osteotomy, a flexor-to-extensor tendon transfer, or a Weil osteotomy with a subsequent flexor-to-extensor tendon transfer with testing in superior subluxation, dorsiflexion, and plantarflexion.

RESULTS

The plantar plate significantly contributed to stabilizing the sagittal plane of the lesser MTP joints. The flexor-to-extensor tendon transfer significantly stabilized the disrupted lesser MTP joints in both superior subluxation and in dorsiflexion. The flexor-to-extensor tendon transfer following a Weil osteotomy also significantly stabilized the disrupted lesser MTP joints in both superior subluxation and in dorsiflexion.

CONCLUSIONS

In this cadaver-based experiment, disruption of the plantar plate of the lesser MTP joints led to significant instability. After plantar plate disruption, the Weil osteotomy left the joint unstable. The flexor-to-extensor tendon transfer by itself increased the stability of the joint in dorsiflexion, but combined with a Weil osteotomy restored near intact stability against superior subluxation and dorsiflexion forces.

CLINICAL RELEVANCE

Surgeons using the Weil osteotomy for plantar plate deficient MTP joints may consider adding a flexor tendon transfer to the procedure. Techniques to repair the torn plantar plate directly are needed.

Biomechanical evaluation of graft fixation techniques for acromioclavicular joint reconstructions using coracoclavicular tendon grafts

BACKGROUND

This study compared the initial strength of acromioclavicular joint reconstructions using coracoclavicular tendon grafts using interference screws, a tendon square knot, or side-to-side suturing for graft fixation.

MATERIALS AND METHODS

An acromioclavicular joint reconstruction was performed using a hamstring allograft looped under the coracoid and then fixed using interference screws, a square knot in the graft, and side-to-side graft suturing in each of 8 cadaveric shoulders. Each reconstruction was cycled in a superior direction, and displacements were recorded. Stiffness and ultimate load to failure of the reconstructions were determined.

RESULTS

The knot construct had a greater elongation after cycling compared with the screw (P = .003) or side-to-side suture (P = .001) repairs and had a higher ultimate load to failure than the screw construct (614.9 ± 124.6 vs 469.79 ± 175.1 N; P = .02). No significant differences were found between the screw and side-to-side suture constructs in elongation (P = .11) or ultimate loads to failure (P = .58). Finally, the side-to-side construct was significantly stiffer than the screw (P = .01) or knot (P = .01) reconstructions.

CONCLUSIONS

Clavicular fixation of a coracoclavicular graft during an acromioclavicular joint reconstruction using a square knot has superior ultimate strength compared with interference screw fixation. Side-to-side suture and screw constructs have superior cyclic displacement properties compared with knot fixation, with no differences in cyclic properties found between the side-to-side suture and screw constructs. Side-to-side suturing provides equivalent initial biomechanical strength compared with interference screw fixation.

Role of collateral ligaments in metatarsophalangeal stability: a cadaver study

BACKGROUND

Lesser metatarsophalangeal joint (MTPJ) instability is a common complaint. The role each of the collateral structures play in maintaining joint stability is unknown.

METHODS

Twenty-six fresh-frozen cadaver lesser MTPJ's were tested for instability with the amount of force necessary to translate the joint 3 mm dorsally. Specimens were tested with 1) intact collateral ligaments, 2) transected accessory collateral or proper collateral ligaments (ACL or PCL), 3) repaired ACL or PCL, 4) transected ACL and PCL, 5) repaired ACL and PCL, and 6) transferred interosseous (IO) tendon. Student t-tests were performed to test for statistical significance (p value less than 0.05).

RESULTS

The mean force required for 3 mm of dorsal displacement was 25 ± 13 N (range, 11 to 52 N) in the 26 specimens. Transecting either the ACL alone or the ACL and PCL led to the most instability versus transecting the PCL alone. Repairing both ligaments improved stability. The IO tendon transfer was comparable to the direct repair of the PCL but was inferior to the direct repair of the ACL.

CONCLUSION

Both ACL and PCL have a stabilizing effect on the MTPJ. However, the ACL was more important since primary transection of the ACL led to more instability and additional transection of the PCL in an ACL deficient model did not lead to significantly more instability.

CLINICAL RELEVANCE

Direct repairs of both structures improved the stability of the joint but not back to normal. IO tendon transfer is a possible adjunct to collateral ligament repairs, but in itself is not sufficient to restore stability.

Effect of lateral offset center of rotation in reverse total shoulder arthroplasty: a biomechanical study

BACKGROUND

Lateral offset center of rotation (COR) reduces the incidence of scapular notching and potentially increases external rotation range of motion (ROM) after reverse total shoulder arthroplasty (rTSA). The purpose of this study was to determine the biomechanical effects of changing COR on abduction and external rotation ROM, deltoid abduction force, and joint stability.

MATERIALS AND METHODS

A biomechanical shoulder simulator tested cadaveric shoulders before and after rTSA. Spacers shifted the COR laterally from baseline rTSA by 5, 10, and 15 mm. Outcome measures of resting abduction and external rotation ROM, and abduction and dislocation (lateral and anterior) forces were recorded.

RESULTS

Resting abduction increased 20° vs native shoulders and was unaffected by COR lateralization. External rotation decreased after rTSA and was unaffected by COR lateralization. The deltoid force required for abduction significantly decreased 25% from native to baseline rTSA. COR lateralization progressively eliminated this mechanical advantage. Lateral dislocation required significantly less force than anterior dislocation after rTSA, and both dislocation forces increased with lateralization of the COR.

CONCLUSION

COR lateralization had no influence on ROM (adduction or external rotation) but significantly increased abduction and dislocation forces. This suggests the lower incidence of scapular notching may not be related to the amount of adduction deficit after lateral offset rTSA but may arise from limited impingement of the humeral component on the lateral scapula due to a change in joint geometry. Lateralization provides the benefit of increased joint stability, but at the cost of increasing deltoid abduction forces.

Mesenchymal stem cells increase collagen infiltration and improve wound healing response to porous titanium percutaneous implants

Epidermal downgrowth, commonly associated with long-term percutaneous implants, weakens the skin-implant seal and greatly increases the vulnerability of the site to infection. To improve the skin attachment and early tissue integration with porous metal percutaneous implants, we evaluated the effect of bone marrow-derived mesenchymal stem cells (BMMSCs) to provide wound healing cues and vascularization to the dermal and epidermal tissues in establishing a barrier with the implant. Two porous metal percutaneous implants, one treated with BMMSCs and one untreated, were placed subdermally on the dorsum of Lewis rats. Implants were evaluated at 0, 3, 7, 28, and 56 days after implantation. Histological analyses evaluated cellular infiltrates, vascularization, quantity and quality of tissue ingrowth, epidermal downgrowth, and fibrous encapsulation. The amount of collagen infiltrating the porous coating was significantly greater for the BMMSC-treated implants at 3 and 28 days post implantation compared to untreated implants. There was an early influx and resolution of cellular inflammatory infiltrates in the treated implants compared to the untreated, though not statistically significant. Vascularization increased over time in both treated and untreated implants, with no statistical significance. Epidermal downgrowth was minimally observed in all implants with or without the BMMSC treatment. Our results suggest that BMMSCs can influence an early and rapid resolution of acute and chronic inflammation in wound healing, and can stimulate early collagen deposition and granulation tissue associated with later stages of wound repair. These findings provide evidence that BMMSCs can stimulate a more rapid and improved barrier between the skin and porous metal percutaneous implant.

Efficacy of a porous-structured titanium subdermal barrier for preventing infection in percutaneous osseointegrated prostheses

Infections of percutaneous osseointegrated prostheses (POP) cause prolonged morbidity and device failure because once established, they are refractory to antibiotic therapy. To date, only limited translational animal studies have investigated the efficacy of POP designs in preventing infections. We developed an animal model to evaluate the efficacy of a porous-coated titanium (Ti) subdermal barrier to achieve skin-implant integration and to prevent periprosthetic infection. In a single-stage "amputation and implantation" surgery, 14 sheep were fitted with percutaneous devices with an attached porous-coated Ti subdermal barrier. Nine sheep were implanted with a smooth Ti subdermal barrier construct and served as controls, with one control sheep removed from the study due to a fractured bone. Clinical, microbiological, and histopathological data showed that the porous Ti barrier prevented superficial and deep tissue infections in all animals (14/14, 100%) at the 9-month endpoint. In contrast, animals with the smooth Ti implant construct had a 25% (2/8) infection rate. Survival analysis indicated a significant difference between the groups (log-rank test, p = 0.018). Data also indicated that although skin marsupialization was evident in both implant types, animals in the control group had a four times greater marsupialization rate. We concluded that osseointegrated implants incorporating porous-coated Ti subdermal barriers may have the ability to prevent infection by maintaining a healthy, biologically attached epithelial barrier at the skin-implant interface in load-bearing animals up to a 9-month terminus.

Cortical bone response to the presence of load-bearing percutaneous osseointegrated prostheses

Although the current percutaneous osseointegrated (OI) prosthetic attachment systems are novel clinical treatments for patients with limb loss, there have only been limited translational studies undertaken to date. To bridge this knowledge gap, from a larger study group of 86 animals that were implanted with a novel percutaneous OI implant construct, 33 sheep were randomly selected from the 0-, 3-, 6-, 9- and 12-month groups for histomorphometric analyses of periprosthetic cortical bone tissue. At necropsy, implanted and nonimplanted limbs were harvested and processed for the evaluation of cortical bone porosity and mineral apposition rate (MAR). The data showed a maximum increase in bone porosity within the first 3 months following implantation and then a progressive reduction in porosity to the baseline steady-state ("Time 0") value by 12 months. The data further verified that the MAR increased during the first 6 months of implantation, reaching a plateau between 6 and 9 months, followed by a progressive decline to the baseline steady state. It was concluded that clinical load bearing and falls precautions, taken during the first 3-6 months following percutaneous OI device implantation surgery, could greatly limit bone fractures during this vulnerable time of increasing cortical bone porosity.

Effect of deltoid tension and humeral version in reverse total shoulder arthroplasty: a biomechanical study

BACKGROUND

No clear recommendations exist regarding optimal humeral component version and deltoid tension in reverse total shoulder arthroplasty (TSA).

MATERIALS AND METHODS

A biomechanical shoulder simulator tested humeral versions (0°, 10°, 20° retroversion) and implant thicknesses (-3, 0, +3 mm from baseline) after reverse TSA in human cadavers. Abduction and external rotation ranges of motion as well as abduction and dislocation forces were quantified for native arms and arms implanted with 9 combinations of humeral version and implant thickness.

RESULTS

Resting abduction angles increased significantly (up to 30°) after reverse TSA compared with native shoulders. With constant posterior cuff loads, native arms externally rotated 20°, whereas no external rotation occurred in implanted arms (20° net internal rotation). Humeral version did not affect rotational range of motion but did alter resting abduction. Abduction forces decreased 30% vs native shoulders but did not change when version or implant thickness was altered. Humeral center of rotation was shifted 17 mm medially and 12 mm inferiorly after implantation. The force required for lateral dislocation was 60% less than anterior and was not affected by implant thickness or version.

CONCLUSION

Reverse TSA reduced abduction forces compared with native shoulders and resulted in limited external rotation and abduction ranges of motion. Because abduction force was reduced for all implants, the choice of humeral version and implant thickness should focus on range of motion. Lateral dislocation forces were less than anterior forces; thus, levering and inferior/posterior impingement may be a more probable basis for dislocation (laterally) than anteriorly directed forces.

Percutaneous osseointegrated prostheses for amputees: Limb compensation in a 12-month ovine model

Percutaneous osseointegrated prostheses are being investigated as an alternative strategy to attach prosthetic limbs to patients. Although the use of these implants has shown to be promising in clinical trials, the ability to maintain a skin seal around an osseointegrated implant interface is a major challenge to prevent superficial and deep periprosthetic infections. The specific aim of this study was to establish a translational load-bearing ovine model to assess postoperative limb compensation and gait symmetry following a percutaneous osseointegrated implant. We tested the following hypotheses: (1) the animals would return to pre-amputation limb loads within 12-months; (2) the animals would return to a symmetrical gait pattern (stride length and time in stance) within 12-months. The results demonstrated that one month following surgery, the sheep loaded their amputated limb to a mean value of nearly 80% of their pre-amputation loading condition; by 12-months, this mean had dropped to approximately 74%. There was no statistical differences between the symmetry of the amputated forelimb and the contralateral forelimb at any time point for the animals stride length or the time spent in the stance phase of their gait cycle. Thus, the data showed that while the animals maintained symmetric gait patterns, they did not return to full weight-bearing after 12-months. The results of this study showed that a large animal load-bearing model had a symmetric gait and was weight bearing for up to 12 months. While the current investigation utilizes an ovine model, the data show that osseointegrated implant technology with postoperative follow-up can help our human patients return to symmetric gait and maintain an active lifestyle, leading to an improvement in their quality of life following amputation.

Micro-CT Density Analysis of the Medial Wall of the Human Medial Cuneiform

The human medial cuneiform is incompletely characterized with regard to anatomical morphology, including mineral density and bone quality. Clinically, we have observed failures of fixation by pull-through of devices through relatively soft medial bone. Defining patterns of relative density may provide valuable information regarding implant placement as higher cortical density bone may offer better resistance to such failures. We sought to identify an area of greatest density along the medial wall of the medial cuneiform.Ten fresh-frozen human cadaveric medial cuneiforms underwent micro-computed tomography imaging. Images were analyzed to obtain densities in 4 quadrants along the medial wall of the medial cuneiform. Seven of 10 specimens revealed a maximum density in the plantar distal quadrant of the medial wall of the medial cuneiform. Chi-square goodness-of-fit testing indicated that the density of this quadrant was significantly different from 3 other quadrants (P<.009). Using the Principle of Standard Residuals, the density of the plantar distal quadrant was significantly different than the other 3.We conclude that the plantar distal quadrant of the medial cuneiform contains bone of maximal density when compared to 3 other quadrants. Surgeons who place implants in this region should be aware that this area might offer better resistance to fixation failure.

A biomechanical analysis of a tensioned suture device in the fixation of the ligamentous Lisfranc injury

BACKGROUND

We hypothesized that using a cadaveric Lisfranc ligamentous injury model, abduction stress would provoke greater post-injury motion than axial weightbearing between the medial cuneiform (MC1) and the base of the second metatarsal (MT2). Second, we hypothesized that both a tensioned suture-button device and a rigid screw fixation method could maintain a reduction and similarly restrain motion to intact (pre-injury) levels.

MATERIALS AND METHODS

Motion was measured between MC1 and MT2 in five matched pairs of human cadaveric feet. Specimens were tested prior to injury, following a transverse ligamentous Lisfranc injury, and then randomized to either screw or tensioned suture-button fixation. Axial then abduction loads were applied. Measurements were repeated after one thousand loading cycles.

RESULTS

With both axial and abduction loads, statistically significant differences in motion were detected between the intact and post-injury conditions, although the magnitudes were greater with abduction (6.8 mm versus 2.0 mm, p = 0.000004). With abduction loads, both fixation methods were effective in restraining motion to pre-injury levels (screw fixation: 1.5 mm intact versus 1.1 mm post-fixation, p = 0.487; suture-button fixation: 1.3 mm intact versus 2.1 mm post-fixation, p = 0.063), and similarly, both devices restrained motion to less than post-injury levels (screw fixation: 8.1 mm post-injury versus 1.1 mm post-fixation, p = 0.001; suture-button fixation: mean 5.5 mm post-injury versus 2.1 mm post-fixation, p = 0.0002). No significant differences in these patterns were detected following cyclic loading.

CONCLUSION

Small, though statistically significant, amounts of motion are produced between MC1 and MT2 with axial loading after a ligamentous Lisfranc injury. With abduction stress, we were able to show a significantly greater difference between pre- and post-injury motion and the ability of both fixation methods to restrain motion to pre-injury levels.

CLINICAL RELEVANCE

Abduction stress may be valuable when diagnosing and testing the transverse ligamentous Lisfranc injury. Both suture-button and screw fixation methods restrain motion at the Lisfranc complex.

Biomechanical comparison of acromioclavicular joint reconstructions using coracoclavicular tendon grafts with and without coracoacromial ligament transfer

PURPOSE

The purpose of this study was to compare the initial strength of acromioclavicular joint reconstructions using coracoclavicular (CC) tendon grafts with and without coracoacromial (CA) ligament transfers.

METHODS

Two different acromioclavicular joint reconstructions were performed in 7 matched pairs of cadaveric shoulders. Paired shoulders were repaired with either a hamstring allograft CC reconstruction (group 1) or a hamstring allograft CC reconstruction plus a CA ligament transfer (group 2). Intact specimens and then reconstructions were cycled from 0 to 100 N at 1 Hz for 100 cycles in a superior direction, and displacements were recorded. Finally, the stiffness of the reconstructions and the ultimate load to failure were recorded.

RESULTS

Superior displacement of the reconstructions after cyclic loading was 4.43 ± 1.82 mm in group 1 and 3.75 ± 1.56 mm in group 2 (P = .38). Ultimate load after load to failure was 970.3 ± 361.03 N in group 1 and 952.7 ± 296.89 N in group 2 (P = .94). Finally, stiffness of the reconstructions was 50.6 ± 6.14 N/mm in group 1 and 65.6 ± 18.45 N/mm in group 2 (P = .12).

CONCLUSIONS

The addition of a transfer of the CA ligament to an acromioclavicular joint reconstruction with a CC hamstring graft does not appear to significantly improve its overall initial biomechanical strength.

CLINICAL RELEVANCE

These data suggest that a CA ligament transfer may add very little to a CC tendon graft reconstruction augmented with high-strength suture with regard to initial, time zero displacement and strength.

Percutaneous implants with porous titanium dermal barriers: an in vivo evaluation of infection risk

Osseointegrated percutaneous implants are a promising prosthetic alternative for a subset of amputees. However, as with all percutaneous implants, they have an increased risk of infection since they breach the skin barrier. Theoretically, host tissues could attach to the metal implant creating a barrier to infection. When compared with smooth surfaces, it is hypothesized that porous surfaces improve the attachment of the host tissues to the implant, and decrease the infection risk. In this study, four titanium implants, manufactured with a percutaneous post and a subcutaneous disk, were placed subcutaneously on the dorsum of eight New Zealand White rabbits. Beginning at four weeks post-op, the implants were inoculated weekly with 10(8) CFU Staphylococcus aureus until signs of clinical infection presented. While we were unable to detect a difference in the incidence of infection of the porous metal implants, smooth surface (no porous coating) percutaneous and subcutaneous components had a 7-fold increased risk of infection compared to the implants with a porous coating on one or both components. The porous coated implants displayed excellent tissue ingrowth into the porous structures; whereas, the smooth implants were surrounded with a thick, organized fibrotic capsule that was separated from the implant surface. This study suggests that porous coated metal percutaneous implants are at a significantly lower risk of infection when compared to smooth metal implants. The smooth surface percutaneous implants were inadequate in allowing a long-term seal to develop with the soft tissue, thus increasing vulnerability to the migration of infecting microorganisms.

The biomechanical contribution of varying posterior constructs following anterior thoracolumbar corpectomy and reconstruction

OBJECT

Thoracolumbar corpectomy is a procedure commonly required for the treatment of various pathologies involving the vertebral body. Although the biomechanical stability of anterior reconstruction with plating has been studied, the biomechanical contribution of posterior instrumentation to anterior constructs remains unknown. The purpose of this study was to evaluate biomechanical stability after anterior thoracolumbar corpectomy and reconstruction with varying posterior constructs by measuring bending stiffness for the axes of flexion/extension, lateral bending, and axial rotation.

METHODS

Seven fresh human cadaveric thoracolumbar spine specimens were tested intact and after L-1 corpectomy and strut grafting with 4 different fixation techniques: anterior plating with bilateral, ipsilateral, contralateral, or no posterior pedicle screw fixation. Bending stiffness was measured under pure moments of +/- 5 Nm in flexion/extension, lateral bending, and axial rotation, while maintaining an axial preload of 100 N with a follower load. Results for each configuration were normalized to the intact condition and were compared using ANOVA.

RESULTS

Spinal constructs with anterior-posterior spinal reconstruction and bilateral posterior pedicle screws were significantly stiffer in flexion/extension than intact spines or spines with anterior plating alone. Anterior plating without pedicle screw fixation was no different from the intact spine in flexion/extension and lateral bending. All constructs had reduced stiffness in axial rotation compared with intact spines.

CONCLUSIONS

The addition of bilateral posterior instrumentation provided significantly greater stability at the thoracolumbar junction after total corpectomy than anterior plating and should be considered in cases in which anterior column reconstruction alone may be insufficient. In cases precluding bilateral posterior fixation, unilateral posterior instrumentation may provide some additional stability.