Ozone-enhanced TiO2 nanotube arrays for the removal of COVID-19 aided antibiotic ciprofloxacin from water: Process implications and toxicological evaluation

The purpose of this study was to evaluate the performance of synthesized TiO₂ nanotube arrays (NTAs) for the removal of the COVID-19 aided antibiotic ciprofloxacin (CIP) and the textile dye methylene blue (MB) from model wastewater. Synthesis of TiO₂ NTAs showed that anodization potential and calcination temperatures directly influence nanotube formation. The increased anodization potential from 10 to 40 V resulted in the development of larger porous nanotubes with a diameter of 36-170 nm, while the collapse of the tubular structure was registered at the highest applied potential. Furthermore, it was found that the 500 °C calcination temperature was the most prominent for the formation of the most photocatalytically active TiO₂ NTAs, due to the optimal anatase/rutile ratio of 4.60. The degradation of both model compounds was achieved with all synthesized TiO₂ NTAs; however, the most photocatalytically active NTA sample was produced at 30 V and 500 ^°C. Compared to photocatalysis, CIP degradation was greatly enhanced by 5-25 times when ozone was introduced to the photocatalytic cell (rates 0.4-4.2 × 10^-1 min^-1 versus 0.07-0.2 × 10^-1 min^-1). This resulted in the formation of CIP degradation by-products, with different mass-to-charge ratios from [M+H]⁺ 346 to 273 m/z. Even though the CIP degradation pathway is rather complex, three main mechanisms, decarboxylation, hydroxylation reaction, and piperazine ring cleavage, were proposed and explained. Furthermore, treated samples were placed in contact with the crustaceans Daphnia magna. It was found that 100% mortality was achieved when approximately 60% of the remaining TOC was present in the samples, indicating that toxic degradation by-products were formed.

Graphene oxide loaded fibrous matrixes of polyether block amide (PEBA) elastomer as an adsorbent for removal of cationic dye from wastewater

Novel highly porous nanoparticle materials are increasingly being applied in adsorption processes, but they need to be supported by robust matrixes to maintain their functionality. We present a study of hosting graphene oxide (GO) particles on polyether block amide (PEBA) melt electrospun fibers and applying such composite matrix to the adsorption of the cationic dye (crystal violet) from water. Various amounts of GO (from 0.5 to 2.0%) were mixed into pure PEBA and electrospun by melt electrospinning obtaining micro fibrous matrixes. These were characterized for morphology (SEM), chemical composition (FTIR), crystallinity (XRD), and wetting behavior (WCA). The increasing amount of GO adversely affected fiber diameter (reduced from 13.18 to 4.38 μm), while the hydrophilic properties (Water contact angle decrease from 109 to 76°) and overall dye adsorption was increased. Efficient adsorption has been demonstrated, reaching approximately 100 % removal efficiency using a 2% GO composite matrix at a dose of 40 mg/l and pH of 10. Further increase of GO concentration in polymer is not feasible due to instability in the electrospinning process.

Sustainable technology for mass production of Ag nanoparticles and Al microparticles from damaged solar cell wafers

Solar cell industry produces high quantities of waste in form of broken, damaged, and rejected cells, whereas milling and filtering practices are typically used to recover the valuable materials (Al, Ag and Si) from such Waste Solar Cell Wafers (WSCWs). This recycling approach has its disadvantages, e.g. excessive energy consumption and dust emission causing loss of valuable metals. To fulfil the concept of Zero Waste for WSCWs, the authors present a sustainable technology for liberation of valuable metals from WSCWs and synthesis of added value products, in particular Ag nanoparticles and Al microparticles. The suggested technology consisted of three different approaches combined to liberate each material individually. The technology started with an Al layer disintegration process using Dimethyl Sulfoxide (as an eco-friendly and sustainable solvent) supported by ultrasonic treatment to break van der Waals' bonding between spherical Al microparticles that compose the Al paste layer, thus liberating Al in microparticle suspension form with particle size ∼3 μm, recovery rate >98%. After that, leaching by nitric acid and other eco-friendly reagents (Sodium Chloride, Ammonia solution and glucose syrup) assisted by ultrasonic treatment was used to dissolve Ag and later precipitate it in form of nanoparticles with avg. size 30 nm, yield >92%. Finally, etching using paste containing phosphoric acid was done to remove anti-reflection coating and purify the Si substrate with final recovery rate >99%. SEM-EDS, XRD, FTIR, and TEM were used for analysis of extracted materials as well as changes in the solvent. Investigation was also concerned with determining economic/global warming impacts of the technology.

Advanced oxidation-based treatment of furniture industry wastewater

The paper presents a study on the treatment of the furniture industry wastewater in a bench scale advanced oxidation reactor. The researched technology utilized a simultaneous application of ozone, ultraviolet radiation and surface-immobilized TiO₂ nanoparticle catalyst. Various combinations of processes were tested, including photolysis, photocatalysis, ozonation, catalytic ozonation, photolytic ozonation and photocatalytic ozonation were tested against the efficiency of degradation. The efficiency of the processes was primarily characterized by the total organic carbon (TOC) analysis, indicating the remaining organic material in the wastewater after the treatment, while the toxicity changes in wastewater were researched by Daphnia magna toxicity tests. Photocatalytic ozonation was confirmed as the most effective combination of processes (99.3% of TOC reduction during 180 min of treatment), also being the most energy efficient (4.49-7.83 MJ/g). Photocatalytic ozonation and photolytic ozonation remained efficient across a wide range of pH (3-9), but the pH was an important factor in photocatalysis. The toxicity of wastewater depended on the duration of the treatment: half treated water was highly toxic, while fully treated water did not possess any toxicity. Our results indicate that photocatalytic ozonation has a high potential for the upscaling and application in industrial settings.

Ozone-UV-catalysis based advanced oxidation process for wastewater treatment

A bench-scale advanced oxidation (AO) reactor was investigated for the degradation of six pollutants (2-naphthol, phenol, oxalic acid, phthalate, methylene blue, and D-glucose) in a model wastewater at with the aim to test opportunities for the further upscale to industrial applications. Six experimental conditions were designed to completely examine the experimental reactor, including photolysis, photocatalysis, ozonation, photolytic ozonation, catalytic ozonation, and photocatalytic ozonation. The stationary catalyst construction was made from commercially available TiO₂ nanopowder by mounting it on a glass support and subsequently characterized for morphology (X-ray diffraction analysis and scanning electron microscopy) as well as durability. The ozone was generated in a dielectrical barrier discharge reactor using air as a source of oxygen. The degradation efficiency was estimated by the decrease in total organic carbon (TOC) concentration as well as toxicity using Daphnia magna, and degradation by-products by ultra-performance liquid chromatography-mass spectrometry. The photocatalytic ozonation was the most effective for the treatment of all model wastewater. The photocatalytic ozonation was most effective against ozonation and photolytic ozonation at tested pH values. A complete toxicity loss was obtained after the treatment using photocatalytic ozonation. The possible degradation pathway of the phthalate by oxidation was suggested based on aromatic ring opening reactions. The catalyst used at this experiment confirmed as a durable for continuous use with almost no loss of activity over time. The design of the reactor was found to be very effective for water treatment using photocatalytic ozonation. Such design has a high potential and can be further upscaled to industrial applications due to the simplicity and versatility of manufacturing and maintenance.