Polybenzoxazine/carbon nanotube nanocomposites as a polymeric sensing material for volatile organic compounds

The emissions of volatile organic compounds (VOCs) have hazardous effects on humans and the environment, and hence they should be detected and reduced. In this study, polybenzoxazine (PBZ) and amine-functionalized multiwall carbon nanotube (MWCNT) composites were synthesized as a sensor for VOCs. MWCNT were functionalized with two types of diamines, namely, 1,6-hexanediamine (HDA) and phenylenediamine (PDA). HDA or PDA treated MWCNTs were loaded into the benzoxazine matrix with different weight percentages (0.1, 0.3, 0.5, and 1%). FTIR analysis confirmed the chemical attachment of the two types of diamines on MWCNT. XRD diffraction and scanning electron microscopy (SEM) were used to investigate the nanofillers morphology and clarify the differences between pristine and amine-functionalized MWCNT. Thermal gravimetric analysis (TGA) was used to study the composites’ thermal stability and degradation behavior. It was found that, in contrast to neat PBZ, the major degradation temperature of PBZ/0.5%MWCNT-PDA nanocomposites were enhanced by 10%. The electrical conductivity of PBZ was 6.32 × 10–9, which was enhanced to 6.11 × 10–7 in the composites with 1% MWCNT-PDA. This material was tested as a VOCs sensor for methanol, acetone, and toluene and showed that PBZ/1% MWCNT-PDA composite responded to all the vapors.

Ocean plastics: environmental implications and potential routes for mitigation - a perspective

This review provides a current summary of the major sources and distribution of ocean plastic contamination, their potential environmental effects, and prospects towards the mitigation of plastic pollution. A characterization between micro and macro plastics has been established, along with a comprehensive discussion of the most common plastic waste sources that end up in aquatic environments within these categories. Distribution of these sources stems mainly from improper waste management, road runoff, and wastewater pathways, along with potential routes of prevention. The environmental impact of ocean plastics is not yet fully understood, and as such, current research on the potential adverse health effects and impact on marine habitats has been discussed. With increasing environmental damage and economic losses estimated at $US 1.5 trillion, the challenge of ocean plastics needs to be at the forefront of political and societal discussions. Efforts to increase the feasibility of collected ocean plastics through value-added commercial products and development of an international supply chain has been explored. An integrative, global approach towards addressing the growing ocean plastic problem has been presented.

Correlation of echocardiographic parameters in prone and supine positions in normal adults using a novel approach

BACKGROUND

Transthoracic echocardiography (TTE) in prone position is challenging. Innovative use of transesophageal echocardiography (TEE) probe to perform TTE for such patients has been described; but reproducibility and correlation of the TTE measurements by this technique with those obtained by the standard supine TTE study are still unknown.

METHODS

We enrolled 30 non-COVID-19 individuals, with a mean (SD) age 35 (10.9) years and 11 females, to study the agreement between the transthoracic measurements of the left ventricular (LV), left atrial (LA), aortic dimensions, and ejection fraction (EF) obtained in prone position using an external TEE probe versus the standard supine position using the conventional TTE probe.

RESULTS

There were no significant differences between LV end-diastolic and end-systolic diameters, septal wall thickness, posterior wall thickness, and aortic root dimensions in the prone versus the supine positions, while the mean EF (60.3% vs 63.1%, P = .014) and mean LA dimensions (1.8 vs 1.9 cm/m² , P < .001) were significantly lower in the prone position. The mean time of scans was significantly longer in the prone as compared to the supine position (12.5 vs 4.5 minutes, P < .001). All supine studies had good quality while in the prone position four studies were of poor quality, and one was nondiagnostic.

CONCLUSIONS

Assessment of cardiac dimensions and systolic function in the prone position using transthoracic TEE probe was feasible. LV and aortic dimensions agreed well with the standard TTE in supine position; however, LA dimensions and EF were lower in the prone position.

Sustainable Biocomposites from Recycled Bale Wrap Plastic and Agave Fiber: Processing and Property Evaluation

Plastic recycling to make sustainable materials is considered one of the biggest initiatives toward a greener environment and socioeconomic development. This research aims to investigate the properties of a blend of recycled bale wrap linear low-density polyethylene (rLLDPE) and polypropylene (PP) (rLLDPE/PP 50:50 wt % matrix), which was further reinforced with 25 wt % agave fiber prepared by injection-molding. Different ratios of a combined industrial compatibilizer (maleic anhydride-grafted PP/PE) were used (1-3 wt %), which were compared with a synthesized compatibilizer made from maleic anhydride-PP/rLLDPE in terms of mechanical and thermomechanical properties of the biocomposites. Incorporation of the compatibilizer in the composite improved the interfacial adhesion between the hydrophobic matrix and the hydrophilic agave fiber, which further increased the mechanical properties and heat deflection temperature of the composite. Scanning electron microscopy showed enhanced compatibility and adhesion between the fiber and the matrix by inclusion of 2 wt % compatibilizer. The synthesized compatibilizer-blended composite showed better mechanical properties than the industrial one, which indicates the potential application of this composite (around 62% recycled material) in the manufacture of packaging materials and commodity products.

Poly(3-hydroxybutyrate)/poly(amine)-coated nickel oxide nanoparticles for norfloxacin delivery: antibacterial and cytotoxicity efficiency

Sustained release dosage forms enable prolonged and continuous release of a drug in the gastrointestinal tract for medication characterized by a short half lifetime. In this study, the effect of blending polyamine on poly(3-hydroxybutyrate) (PHB) as a carrier for norfloxacin (NF) was studied. The prepared blend was mixed with different amounts of NiO nanoparticles and characterized using FTIR analysis, X-ray diffraction analysis, thermogravimetric analysis, dynamic light scattering, transmission electron microscopy and scanning electron microscopy. It was found that the drug released from the nanocomposite has a slow rate in comparison with NiO, PHB, and PHB/polyamine blend. The highest ratio of NiO content to the matrix (highest NF loading), leads to a slower rate of drug release. The release from the nanocomposites showed a faster rate at pH = 2 than that at pH = 7.4. The mechanisms of NF adsorption and release were studied on PHB/polyamine-3% NiO nanocomposite. In addition, the antimicrobial efficacy of nanocomposites loaded with the drug was determined and compared with the free drug. Inclusion of NiO into PHB/polyamine showed a higher efficacy against Streptococcus pyogenes and Pseudomonas aeruginosa than the free NF. Moreover, the cytotoxicity of PHB/polyamine-3% NiO against HePG-2 cells was investigated and compared with PHB and PHB/polyamine loaded with the drug. The most efficient IC50 was found for NF@PHB/polyamine-3% NiO (29.67 μg mL-1). No effect on cell proliferation against the normal human cell line (WISH) was observed and IC50 was detected to be 44.95 and 70 μg mL-1 for NiO nanoparticles and the PHB/polyamine-3% NiO nanocomposite, respectively indicating a selectivity of action towards tumor cells coupled with a lack of cytotoxicity towards normal cells.

Additional diagnostic accuracy of global longitudinal strain at peak dobutamine stress in patients with moderate pretest probability of coronary artery disease

BACKGROUND

Previous studies confirmed the feasibility of 2D speckle tracking echocardiography (2D STE) during dobutamine stress echocardiography (DSE) in assessing myocardial ischemia in patients with previous myocardial infarction. It is unknown whether it improves the diagnostic accuracy in young patients with intermediate pretest probability for coronary artery disease (CAD) and no prior cardiovascular events.

METHODS

We prospectively studied 101 patients by DSE and STE, followed by coronary angiography within 1 month. Significant CAD was defined as diameter stenosis ≥ 50%. Receiver operating characteristic analysis obtained global longitudinal strain (GLS) cutoff values of significant area under the curve (AUC).

RESULTS

Mean age: 53 ± 8 years, 56% females, 49 had significant CAD (group 1) and 52 had normal/mild CAD (group 2); no significant baseline differences except more males in group 1 (P: .002). DSE sensitivity and specificity for CAD were 79.6% and 92.3%, respectively, positive predictive value (PPV): 90.6%, negative predictive value (NPV): 82.7%, and diagnostic accuracy: 86%. At peak stress, all strain parameters were significantly lower in group 1. However, GLS had the highest AUC: 0.88, P: <.001. GLS cutoff value ≤ -20.5 had 89.8% sensitivity, 84.6% specificity, 84.6% PPV, 89.8% NPV, and 87% diagnostic accuracy. Combining GLS cutoff with DSE had higher AUC than either alone (0.9, P < .001): 95.9% sensitivity, 84.6% specificity, 85.5% PPV, 95.7% NPV, and 90% diagnostic accuracy.

CONCLUSION

2D-STE-derived GLS increases DSE precision to detect CAD in intermediate pretest probability patients: It improves DSE sensitivity, NPV, and accuracy. It is reproducible and has comparable specificity.

Hybrid biocomposites from polypropylene, sustainable biocarbon and graphene nanoplatelets

Polypropylene (PP) is an attractive polymer for use in automotive parts due to its ease of processing, hydrophobic nature, chemical resistance and low density. The global shift towards eliminating non-renewable resource consumption has promoted research of sustainable biocarbon (BioC) filler in a PP matrix, but this material often leads to reduction in composite strength and requires additional fillers. Graphene nano-platelets (GnPs) have been the subject of considerable research as a nanofiller due to their strength, while maleic anhydride grafted polypropylene (MA-g-PP) is a commonly used compatibilizer for improvement of interfacial adhesion in composites. This study compared the thermo-mechanical properties of PP/BioC/MA-g-PP/GnP composites with varying wt.% of GnP. Morphological analysis revealed uniform dispersion of BioC, while significant agglomeration of GnPs limited their even dispersion throughout the PP matrix. In the optimal blend of 3 wt.% GnP and 17 wt.% BioC biocontent, tensile strength and modulus increased by ~19% and ~22% respectively, as compared to 20 wt.% BioC biocomposites. Thermal stability and performance enhancement occurred through incorporation of the fillers. Thus, hybridization of fillers in the compatibilized matrix presents a promising route to the enhancement of material properties, while reducing petroleum-based products through use of sustainable BioC filler in composite structures.

Impact of Dorsal Preservation Rhinoplasty Versus Dorsal Hump Resection on the Internal Nasal Valve: a Quantitative Radiological Study

BACKGROUND

This study evaluates the impact of different hump takedown techniques, namely the conventional hump resection with midvault reconstruction, the push-down (PD) and the let-down (LD) procedures, on the INV dimensions.

METHODS

In this cadaveric study, six heads were divided randomly into either the conventional hump resection technique (Group A; n = 6 sides) or DPR techniques (n = 6 sides). This latter group was subdivided such that initially a PD procedure was performed (Group B; n = 6 sides), followed by a LD procedure on the same heads (Group C; n = 6 sides). A validated radiological method was used to measure the INV angle and cross-sectional area (CSA) in a modified coronal plane both pre- and post-procedurally.

RESULTS

Group A did not show significant reduction in the INV angle nor in CSA (p = 0.068 and p = 0.156, respectively). In the push-down group (B), we observed a mean change of 2.05° in the angles and 0.3 cm² in the CSA (p = 0.0163 and p < 0.001, respectively). The LD group (C) did not show significant reduction in the INV angle nor in CSA (p = 0.437 and p = 0.331, respectively).

CONCLUSION

Neither the conventional hump resection nor the LD DPR technique reduced the INV dimensions. However, the PD preservation technique significantly reduced the INV dimensions.

LEVEL OF EVIDENCE III

This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266.

Hybrid Green Bionanocomposites of Bio-based Poly(butylene succinate) Reinforced with Pyrolyzed Perennial Grass Microparticles and Graphene Nanoplatelets

Bio-based poly(butylene succinate) (BioPBS) was combined with pyrolyzed Miscanthus microparticles (biocarbon) and graphene nanoplatelets to create a hybrid bionanocomposite. Pyrolyzed biomass, known as biocarbon, was incorporated into a BioPBS matrix to improve the thermo-mechanical properties of the bioplastic while simultaneously increasing the value of this co-product. Biocomposites loaded with 25 wt % biocarbon showed 57, 13, and 32% improvements in tensile modulus, heat deflection temperature, and thermal expansion, respectively. Further improvements were found when graphene nanoplatelets (GnPs) were added to the biocomposite, forming a hierarchical hybrid bionanocomposite. Two processing methods were used to incorporate graphene into the composites: (I) graphene, BioPBS, and biocarbon were added together and directly compounded, and (II) a masterbatch of graphene and BioPBS was processed first and then diluted to the same ratios as those used in the direct compounding method I. The two methods resulted in different internal morphologies that subsequently impacted the mechanical properties of the composites; little change was observed in the thermal properties studied. Bionanocomposites processed using the direct compounding technique showed the greatest increase in tensile strength and modulus: 17 and 120%, respectively. Bionanocomposites processed using a masterbatch technique had slightly lower strength and modulus but showed almost twice the impact strength compared with the direct compounding method. This masterbatch technique was found to have a superior balance of stiffness and toughness, likely due to the presence of superclustered graphene platelets, confirmed through a scanning electron microscope and a transmission electron microscope.

Injection Molded Novel Biocomposites from Polypropylene and Sustainable Biocarbon

Achieving sustainability in composite materials for high-performance applications is a key issue in modern processing technologies. In this work, the structure-property relationships of injection molded polypropylene (PP)/biocarbon composites were investigated with a focus on the thermal properties and specific emphasis on the coefficient of linear thermal expansion (CLTE). Biocomposites were produced using 30 wt.% biocarbon in a PP matrix, and two different sources of biocarbon produced at ~650 and 900 °C were used. The overall results were compared with 30 wt.% glass- and talc-filled PP composites. Due to the lamellar morphology of the talc developed during the extrusion-injection molding processing, talc-filled composites showed an increase in the CLTE in the normal direction (ND), and a reduction in the flow direction (FD) with respect to the neat polymer. Glass fiber composites also showed an improvement in the CLTE with respect to the neat polymer. However, the biocarbon-based composites showed the best properties in the ND, with improved values in biocarbon produced at higher temperature. The FD values for both biocarbon composites were improved with respect to the matrix, while biocarbon created at lower temperature showed slightly lower expansion values. A comprehensive explanation of these overall phenomena is supported by a series of morphological, thermal, mechanical and rheological tests.