In situ electrochemical potential-induced synthesis of metal organic framework membrane on polymer support for H2/CO2 separation

Metal-Organic Framework (MOF) membranes act as selective layers have offered unprecedented opportunities for energy-efficient and cost-effective gas separation. Searching for the green and sustainable synthesis method of dense MOF membrane has received huge attention in both academia and industry. In this work, we demonstrate an in situ electrochemical potential-induced synthesis strategy to aqueously fabricate Metal Azolate Framework-4 (MAF-4) membranes on polypropylene (PP) support. The constant potential can induce the heterogeneous nucleation and growth of MAF-4, resulting an ultrathin membrane with the thickness of only 390 nm. This high-quality membrane exhibits a high H2/CO2 separation performance with the H2 permeance as high as 1565.75 GPU and selectivity of 11.6. The deployment of this environment friendly one-step fabrication method under mild reaction conditions, such as low-cost polymer substrate, water instead of organic solvent, room temperature and ambient pressure shows great promise for the scale-up of MOF membranes.

Thermal self-crosslink after etching for regulated preparation of Ti3C2 type MXene membrane and its preliminary gas separation

We present an innovative methodology for the synthesis of MXene membranes through a dual-stage process involving etching and subsequent thermal self-crosslinking. A molar ratio of 1 (Al3+):9 (F-) using HCl/LiF was employed to convert raw Ti3AlC2 (MAX phase) into MXene within 48 h at 40 °C. This procedure predominantly yielded monolayers distinguished by diameters exceeding 500 nm, elevated crystallinity and a high overall yield. Advanced characterization techniques, including FESEM, TEM, HRTEM, AFM, XPS, and FTIR, were utilized. Instrumental analysis confirmed the formation of MXene exhibiting a single-flake morphology with diameters exceeding 500 nm. These monolayers were intact and continuous, with smooth peripheries and a uniform thickness of 2.1 nm. The surfaces were predominantly composed of carbon (C), oxygen (O), and titanium (Ti) atoms, interconnected by chemical bonds such as C-Ti-O, C-Ti-OH, C-C, C-O, and Ti-O. In the subsequent phase, vacuum filtration facilitated the assembly of a self-supporting MXene membrane. Thermal treatment at 170 °C for 30 h resulted in the reinforcement of C-Ti-O bonds within the nanosheets, increasing their prevalence to 43.14 % and 19.47 %, respectively. This thermal regulation reduced the interlayer d-spacing from 4.33 to 3.54 Å, which significantly improved the gas separation efficiency beyond the Knudsen diffusion limit, as demonstrated by the α H 2 / C F 4 value exceeding 23.0.

Recent advancements in polyurethane-based membranes for gas separation

Gas separation membranes are critical in a variety of environmental research and industrial applications. These membranes are designed to selectively allow some gases to flow while blocking others, allowing for the separation and purification of gases for a variety of applications. Therefore, the demand for fast and energy-efficient gas separation techniques is of central interest for many chemical and energy production diligences due to the intensified levels of greenhouse and industrial gases. This encourages the researchers to innovate techniques for capturing and separating these gases, including membrane separation techniques. Polymeric membranes play a significant role in gas separations by capturing gases from the fuel combustion process, purifying chemical raw material used for plastic production, and isolating pure and noncombustible gases. Polyurethane-based membrane technology offers an excellent knack for gas separation applications and has also been considered more energy-efficient than conventional phase change separation methodologies. This review article reveals a thorough delineation of the current developments and efforts made for PU membranes. It further explains its uses for the separation of valuable gases such as carbon dioxide (CO2), hydrogen (H2), nitrogen (N2), methane (CH4), or a mixture of gases from a variety of gas spillages. Polyurethane (PU) is an excellent choice of material and a leading candidate for producing gas-separating membranes because of its outstanding chemical chemistry, good mechanical abilities, higher permeability, and variable microstructure. The presence of PU improves several characteristics of gas-separating membranes. Selectivity and separation efficiency of PU-centered membranes are enhanced through modifications such as blending with other polymers, use of nanoparticles (silica, metal oxides, alumina, zeolite), and interpenetrating polymer networks (IPNs) formation. This manuscript critically analyzes the various gas transport methods and selection criteria for the fabrication of PU membranes. It also covers the challenges facing the development of PU-membrane-based separation procedures.

A pilot study to capture methane from the exhausted air of dairy cows using a cryogenic approach

In the agricultural sector, ruminants are the largest methane (CH4) emission source and many efforts have been undertaken to reduce these greenhouse gas emissions, while compromising animal health and physiology. On the other hand, ruminal CH4, which is biomethane, is in high demand, especially in its liquid form (LBM) that can be used as high energy density fuel. However, CH4 released from a ruminant is immediately mixed with air and highly diluted (<0.1%), challenging CH4 capture technologies. Here we aimed to construct a cryogenic pilot system to capture and liquefy enteric CH4 released from dairy cows kept in respiration chambers. To approach this aim, the outlet air from the chambers was directed through a two-step cooling trap to capture CO2 (-120 to -130 °C) as a solid in the first and CH4 and O2 as liquids in the second cooler (-160 to -180 °C). Warming the second cooler resulted in the evaporation of O2, thereby separating O2 and CH4. LBM purity was in average 90% and was lowest at warming rates higher than 0.88 °C/min. The mean CH4 capture efficiency was 92% and found to be independent of sequestration time and flow rate. However, an increase in CH4 concentration to 0.6%, as it occurs directly at the muzzle of a cow, reduced the sequestration time for CH4. These results show that cryogenic technology can be used to obtain LBM from the air containing ultra-low CH4 concentrations as it is found in cattle barns with high efficiency and purity.

Innovative strategies for enhancing gas separation: Ionic liquid-coated PES membranes for improved CO2/N2 selectivity and permeance

As a cost-effective advancement in membrane technology, this study investigates the impact of PEG additive and CBT on the structural, stability, and gas permeance properties of PES-coated membranes, utilizing 1-dodecyl-3-methylimidazolium chloride ionic liquid ([DDMI][Cl] IL) as a carrier liquid. BET and FT-IR analyses highlight the significant enhancement in performance through the immobilization of pores with [DDMIM][Cl] IL. The investigation focuses on PES-M5-coated membranes, revealing excellent stability in finger-like pore structures prepared through direct immersion and nitrogen pressure immobilization. PES-M5-coated membranes with [DDMIM][Cl] IL via direct immersion experience lower weight loss than those coated using nitrogen pressure, with critical pressures at 1.4 and 1.25 bar, respectively. The study identifies PES-coated membranes, particularly PES-M25 (20.88 GPU) with macro-void pores and PES-M5 (29 GPU) with finger-like pores, exhibiting the highest CO2 permeance and CO2/N2 selectivity. As a cost-effective advancement in membrane technology, ionic liquids are employed in support membranes to enhance gas separation. Employing pure PES membranes with varying pore structures, created through the NIPS method, the study immobilizes [DDMI][Cl] IL in membrane pores through nitrogen pressure and direct immersion. Results underscore the successful application of porous support materials coated with ionic liquids for continuous CO2 and sulfur compound separation, showcasing competitive permeability and selectivity compared to traditional polymer membranes.

Graphene-modified MIL-125-NH2 mixed matrix membranes for efficient H2 and CH4 purification

This study investigates the performance of the mixed matrix membranes (MMMs) incorporating hybrid fillers of metal-organic framework (MIL-125-NH2) and graphene nanosheets (GNs) for enhanced methane (CH₄) and hydrogen (H₂) separation in the purification sector. The physico-chemical properties of the MMMs were evaluated by SEM, XRD, FTIR, AFM, TGA, DTG, and Brunauer-Emmett-Teller. The permeability and selectivity of the MMMs were determined using different single gases (CO2, N2, H2, and CH4) at various temperatures (20-60 °C). Optimization of fabrication parameters resulted in a significant improvement in porosity and roughness of the fabricated MMMs. The permeabilities of the MOF/PES membrane are 20.3 (CO2), 23.9 (N2), 32.2 (CH4), and 24.1 (H2) x 104 Barrer, while incorporating 0.05 wt% of GNs into the MOF/PES membrane improved the permeability by 36 % (CO2), 41 % (N2), 31 % (CH4), and 370 % (H2). In addition, the H2/CO2 and H2/N2 selectivities of the MMMs significantly increased up to 4 and 3.3, with an improvements of 236 % and 230 %, respectively, compared to the MOF/PES membrane. Furthermore, the CH4/CO2 and CH4/N2 selectivities of the MMMs decreased by 4 %. Therefore, a hybrid filler (10 wt % of MIL-125-NH2 and 0.05 wt % of GNs is highly recommended to improve the permeability and selectivity of the PES membrane, expanding its potential applications in CH4 and H2 purification.

ZIF-8 @polycarbonate nanocomposite membranes for improved permeability and selectivity for hydrogen gas

Through this work, we are reporting high-performance ZIF-8 @polycarbonate nanocomposite membranes with satisfactory structural stability for improving the gas separation performance. ZIF-8 nanoparticles were synthesised using the wet chemical route with cubic morphology and controlled size using CTAB as a surfactant. The membranes were prepared using the solution casting method by adding ZIF-8 filler at various concentrations. The synthesised filler material and MMMs were characterised through X-ray diffraction spectroscopy (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and RAMAN spectroscopy techniques. The gas separation measurements were taken using H2, CO2, and N2 gas in the purest form. The SEM results confirm the formation of spherulite-like morphology with the addition of ZIF-8 due to the crystallisation of the polymer, which increased the membrane's free volume and opened up additional pathways for the transportation of the gas molecules. The gas separation results confirmed that the 15 wt% ZIF-8/PC nanocomposite membrane showed the maximum H2 permeability of 180,970 barrer with an increment of 316.03%, while H2/CO2 and H2/N2 selectivity showed the increments of 89.43% and 103.64%, respectively. Therefore, this PC/ZIF-8 system seems to be a promising approach to developing new H2 selective membranes with high gas permeability and gas selectivity values.

Closo-[B12 H12 ]2- Derivatives with Polar Groups As Promising Building Blocks in Metal-Organic Frameworks for Gas Separation

Engineering design of metal organic frameworks (MOFs) for gas separation applications is nowadays a thriving field of investigation. Based on the recent experimental studies of dodecaborate-hybrid MOFs as potential materials to separate industry-relevant gas mixtures, we herein present a systematic theoretical study on the derivatives of the closo-dodecaborate anion [B12 H12 ]2- , which can serve as building blocks for MOFs. We discover that amino functionalization can impart a greater ability to selectively capture carbon dioxide from its mixtures with other gases such as nitrogen, ethylene and acetylene. The main advantage lies in the polarization effect induced by amino group, which favors the localization of the negative charges on the boron-cluster anion and offers a nucleophilic anchoring site to accommodate the carbon atom in carbon dioxide. This work suggests an appealing strategy of polar functionalization to optimize the molecule discrimination ability via preferential adsorption.

A critical review in recent progress of hollow fiber membrane contactors for efficient CO2 separations

Among wide range of membrane-based operations, membrane contactors, as they reify comparatively modern membrane-based mechanism are gaining quite an attention in both pilot and industrial scales. In recent literature, carbon capture is one of the most researched applications of membrane contactors. Membrane contactors have the potential to minimize the energy consumption and capital cost of traditional CO₂ absorptions columns. In a membrane contactor, CO₂ regeneration can take place below the solvent boiling point, resulting into lower consumption of energy. Various polymeric as well as ceramic membrane materials have been employed in gas liquid membrane contactors along with several solvents including amino acids, ammonia, amines etc. This review article provides detailed introduction of membrane contactors in terms of CO₂ removal. It also discusses that the main challenge that is faced by membrane contactors is membrane pore wetting caused by solvent that in turn can reduce the mass transfer coefficient. Other potential challenges such as selection of suitable solvent and membrane pair as well as fouling are also discussed in this review and are followed by potential ways to reduce them. Furthermore, both membrane gas separation and membrane contactor technologies are analysed and compared in this study on the basis of their characteristics, CO₂ separation performances and techno economical transvaluation. Consequently, this review provides an opportunity to thoroughly understand the working principle of membrane contactors along its comparison with membrane-based gas separation technology. It also provides a clear understanding of latest innovations in membrane contactor module designs as well as challenges encountered by membrane contactors along with possible solutions to overcome these challenges. Finally, semi commercial and commercial implementation of membrane contactors has been highlighted.

Effect of Co-existing gases on hydrogen permeation through a Pd82-Ag18/α-Al2O3 membrane during transient start-up

The work aimed to study the influence of co-existing gaseous mixture (H₂-N₂-CO-CO₂) on hydrogen permeation through the counter-current flow of a Pd82-Ag18/α-Al₂O₃ membrane during transient start-up at 350 °C and atmospheric pressure. The membrane was operated for an 8-h. Its performance was measured in terms of hydrogen flux and recovery. The results were mapped on Sieverts-Fick's line and showed a slight membrane deactivation because of the presence of N₂ and CO₂ in the feed gas. The membrane deactivation became more profound when CO was a constituent. The effect of the co-existing gases on the hydrogen flux, in increasing order, was CO > CO₂>N₂. The co-existing gases, if present as a significant fraction, induces dilution, concentration polarization, and inhibition over the membrane surface, decreases the membrane performance in term of hydrogen recovery, time lag during transient start-up, and deactivation. It is recommended that the start-up might be run using equimolar H₂-N₂ mixture.

Reinforcement of single-walled carbon nanotubes on polydimethylsiloxane membranes for CO2, O2, and N2 permeability/selectivity

In this study, PDMS incorporated with SWCNTs have been fabricated via solution casting method for industrial applications and characterized by the analyses of SEM, FTIR, TGA, AFM, and MST. The modified membranes were further analyzed for CO₂, O₂, and N₂ gas permeability. The strategic membranes have five different weight ratios (0.013, 0.025, 0.038, 0.050, 0.063) compared to neat PDMS membranes. The even distribution of SWCNTs in PDMS provided results that showed improvement in thermal stability. However, mechanical strength has been weakened with increased concentration of nanofiller because of the increase in the number of SWCNTs by increases that imperfections become more severe. The designed polymeric membranes with good thermal stability and adequate mechanical strength can be used for the selectivity and permeability of CO₂, O₂, and N₂ gases. The effect of the PDMS-SWCNTs on gas permeability has been studied. 0.063 wt.% SWCNTs presented the maximum permeability of CO₂ gas while maximum O₂ and N₂ gas permeability have been obtained by 0.013 wt.% SWCNTs. The ideal selectivity of mixed (50:50) gas conditions has been tested. The maximum CO₂/N₂ ideal selectivity was obtained by 0.050 and 0.063 wt.% SWCNTs while maximum O₂/N₂ ideal selectivity obtained by 0.050 wt.% SWCNTs. Therefore, the fabrication of this novel SWCNTs-PDMS membrane may lead to separating the industrial exhaust and be used as a potential membrane for environmental remediation in the future.

Membrane-based carbon capture: Recent progress, challenges, and their role in achieving the sustainable development goals

The rapid growth in the consumption of fossil fuels resulted in climate change and severe health issues. Among the different proposed methods to control climate change, carbon capture technologies are the best choice in the current stage. In this study, the various membrane technologies used for carbon capture and their impact on achieving sustainable development goals (SDGs) are discussed. Membrane-based carbon capture processes in pre-combustion and post-combustion, which are known as membrane gas separation (MGS) and membrane contactor (MC), respectively, along with the process of fabrication and the different limitations that hinder their performances are discussed. Additionally, the 17 SDGs, where each representing a crucial topic in the current global task of a sustainable future, that are impacted by membrane-based carbon capture technologies are discussed. Membrane-based carbon capture technologies showed to have mixed impacts on different SDGs, varying in intensity and usefulness. It was found that the membrane-based carbon capture technologies had mostly influenced SDG 7 by enhancement in the zero-emission production, SDG 9 by providing 38-42% cost savings compared to liquid absorption, SDG 3 through reducing pollution and particulate matter emissions by 23%, and SDG 13, with SDG 13 being the most positively influenced by membrane-based carbon capture technologies, as they significantly reduce the CO₂ emissions and have high CO₂ capture yields (80-90%), thus supporting the objectives of SDG 13 in combatting climate change.

Synthesis of ZIF-8 tubular membrane via solvent evaporation seeding coupled with microwave assisted heating method for separation of small molecule gases

In this work, we systematically study the performance of tubular ZIF-8 membranes in the separation of small molecules including H₂, CO₂, N₂ and CH_4. The tubular ZIF-8 membranes were synthesized on α-alumina support via novel dual approach known as solvent evaporation seeding coupled with microwave assisted growth. The durations for the growth of the seed layer through solvent evaporation and membrane layer via microwave heating were varied. The crystallinity and morphology of the resultant membranes were evaluated by using XRD, SEM and IFM analyses. The performance of the resultant tubular ZIF-8 membranes was assessed for small molecule gases permeation at various pressures and temperatures. Highest flux ranging from 0.02 to 0.61 mol/m²s were obtained for gases CO₂, CH₄, N₂, and H₂ at feed pressure of 10 bar, whereas highest ideal selectivity of 12.4, 9.3 and 6.9 were obtained for H₂/CH_4, CO₂/CH₄, N₂/CH₄, respectively, at feed pressure of 10 bar and temperature of 30 °C. This work reveals that the tubular ZIF-8 membrane can be synthesized via a feasible and reproducible solvent evaporation seeding coupled with microwave assisted growth method, which can be further explored for the upscaling of the ZIF-8 tubular membrane in pilot scale for gas separation application.

Advances in two-dimensional materials for energy-efficient and molecular precise membranes for biohydrogen production

Waste management has become an ever-increasing global issue due to population growth and rapid globalisation. For similar reasons, the greenhouse effect caused by fossil fuel combustion, is leading to chronic climate change issues. A novel approach, the waste-to-hydrogen process, is introduced to address the concern of waste generation and climate change with an additional merit of production of a renewable, higher energy density than fossil fuels and sustainable transportation fuel, hydrogen (H2) gas. In the downstream H2 purifying process, membrane separation is one of the appealing options for the waste-to-hydrogen process given its low energy consumption and low operational cost. However, commercial polymeric membranes have hindered membrane separation process due to their low separation performance. By introducing novel two-dimensional materials as substitutes, the limitation of purifying using conventional membranes can potentially be solved. Herein, this article provides a comprehensive review of two-dimensional materials as alternatives to membrane technology for the gas separation of H2 in waste-to-hydrogen downstream process. Moreover, this review article elaborates and provides some perspectives on the challenges and future potential of the waste-to-hydrogen process and the use of two-dimensional materials in membrane technology.

Evaluation of polymeric membranes' performance during laboratory-scale experiments, regarding the CO2 separation from CH4

The present study evaluates the separation performance of a commercially available polymeric membrane, when employed for the upgrade of biogas to enrich CH₄ from a simulated binary gas mixture. For this purpose, a laboratory-scale membrane set-up device has been designed and assembled, aiming to achieve the production of high purity biomethane (>95%) with simultaneous recycling and utilization of the (considered as) waste CO₂ stream. The examined membrane is a polysulfone (PSF) hollow fiber (HF) one, applied in counter-current flow. The feed concentration of gases consisted between 55-70 vol% and 45-30 vol%, regarding CH₄ and CO₂ respectively, whereas the effect of retentate pressure was studied in the range between 0.7 and 1.5 bars. The experimental results reveal that the concentration of CH₄ in the retentate stream can exceed the target value of 95%, when the applied pressure values are above the limit of 1 bar. Any increase in the feed pressure can lead also to higher CH₄ purity on the retentate side, however the retentate mass flow decreases, leading to smaller recovery values of CH₄. A significant increase in the CH₄ purity is observed, when the CH₄ recovery drops below 40%, suggesting the need for the application of multiple membrane modules, operating in series. Regarding the CO₂ concentration in the permeate stream, its percentages range between 30 and 50%, which are not considered as sufficient to permit immediate reuse, whereas the need of extra membrane modules to improve the purity of gas streams is confirmed.

Polymeric composite membranes in carbon dioxide capture process: a review

Carbon dioxide (CO₂) emission to the atmosphere is the prime cause of certain environmental issues like global warming and climate change, in the present day scenario. Capturing CO₂ from various stationary industrial emission sources is one of the initial steps to control the aforementioned problems. For this concern, a variety of resources, such as liquid absorbents, solid adsorbents, and membranes, have been utilized for CO₂ capturing from various emission sources. Focused on membrane-based CO₂ capture, polymeric membranes with composite structure (polymeric composite membrane) offer a better performance in CO₂ capturing process than other membranes, due to the composite structure it offers higher gas flux and less material usage, thus facile to use high performed expensive material for membrane fabrication and achieved good efficacy in CO₂ capture. This compressive review delivers the utilization of different polymeric composite membranes in CO₂ capturing applications. Further, the types of polymeric materials used and the different physicochemical modifications of those membrane materials and their CO₂ capturing ability are briefly discussed in the text. In conclusion, the current status and possible perspective ways to improve the CO₂ capture process in industrial CO₂ gas separation applications are described in this review.

Effectiveness of ionic liquid-supported membranes for carbon dioxide capture: a review

The world's population explosion creates a need for natural resources for energy, which will become a significant contributor to global climate change. As we all know, carbon dioxide (CO₂) is one of the most critical elements of the global greenhouse gas effect. CO₂ capture and storage innovations have piqued researchers' attention in recent decades. Compared to other methods, membrane separation has some positive performance in CO₂ capture. CO₂ capture with membrane separation using enhanced ionic liquids (ILs) is described in this review. ILs have made an appearance in CO₂ capture work as the potential additive, and companies and academics have been interested in CO₂ separation for the past two decades. This article comprehensively analyzes the current modern approach in ILs and IL-based membranes for gas separation processes. Based on the latest literature and performance data, this work provides a complete compressive examination of types of ILs and IL-supported membrane performances. ILs for CO₂ capture were also explored, and IL-based membranes for different ILs were also studied. This study emphasizes the supremacy of novel ILs for CO₂ capture in membrane separation.

Crystal Structure Transformation in Hydrogen-bonded Organic Frameworks via Ion Exchange

Hydrogen-bonded organic frameworks (HOFs) have emerged as rapidly growing porous materials while established permanent porosities are very fragile and difficult to stabilize due to weak hydrogen-bonding interactions among building units. Herein, we report a stable hydrogen-bonded metallotecton framework (termed as HOF-ZJU-102) that was constructed through hydrogen-bonding networks between cationic metal-organic complexes [Cu₂ (Hade)₄ (H₂ O)₂ ]⁴⁺ (Hade=adenine) and GeF₆ ^2- anions. The framework not only shows permanent porosity, but also exhibits efficient separation performance of C₂ H₂ /C₂ H₄ at room temperature. More interestingly, its crystal structure could be irreversibly transformed into isostructural counterpart HOF-ZJU-101 by ion exchange in the SiF₆ ^2- containing solution, evidenced by multiple characterization techniques including gas sorption measurements, ¹⁹ F NMR spectra, FTIR and EDS. Utilizing such an ion exchange mechanism, the collapsed HOF-ZJU-102 could be restored into HOF-ZJU-101 by simply soaking in the salt solution.

Valorization of shrimp shell biowaste for environmental remediation: Efficient contender for CO2 adsorption and separation

Over the years, single heteroatom-doped biowaste-derived activated carbons were studied for effective CO₂ adsorption. However, binary or ternary heteroatoms-doping is equally important and could significantly affect the CO₂ adsorption and flue gas (i.e., CO₂/N₂) separation. Herein, for the first time, shrimp shell-derived chitosan was used to design a series of ternary (N, S, O)-doped hierarchically porous carbons. The resultant carbons exhibit a large specific surface area (up to 2095 m²/g), micropore volume (up to 1.2647 cm³/g), and high heteroatoms content i.e., N up to 4.1 at. %, S up to 4.6 at. %, and O up to 13.4 at. %. Consequently, high CO₂ uptake of 236.80 mg/g at 273 K/1 bar and an excellent CO₂/N₂ gas selectivity (84.3) was observed, attributed to the synergistic role of narrow micropores (<1 nm) and optimum heteroatom content. Furthermore, the stable CO₂ adsorption-desorption cyclic behavior under flue gas conditions i.e., 15% CO₂/85% N₂ reveals the physisorption mechanism of CO₂ adsorption and appears to be an energy-efficient regeneration process. Concluding, our work demonstrates a facile route of valorization of biowaste for environmental remediation to combat biowaste accumulation and mitigating atmospheric CO₂ levels, simultaneously.

Density functional theory-based analyses on selective gas separation by β-PVDF-supported ionic liquid membranes

Finding proper candidates for polymer-supported ionic liquid (IL)-based gas separating membranes is a challenge. The current article elucidates the quantum chemical perspective of the selective gas adsorption efficiency, from a mixture of CO₂, CO, CH₄, and H₂, of α- and β-polyvinylidene fluoride (PVDF)-supported imidazolium- and pyridinium-based six ionic liquid membranes. Although IL-based membrane efficiency mainly depends on the gas solubility of ILs, IL/support binding and gas adsorption on the support material are also studied to describe the overall gas adsorption properties of the PVDF/IL complexes. β-PVDF exhibits better binding with the ILs, and better gas affinity, thus, qualified as a more suitable membrane component as compared to α-PVDF. Dispersion-corrected density functional calculations are performed to provide a detailed insight into the energetic interactions, nonbonding intermolecular interactions based on symmetry adapted perturbation theory (SAPT), natural bond orbitals (NBO), Bader's quantum theory of atoms in molecules (QTAIM), reduced density gradient (RDG), frontier orbital interactions, density of states (DOS), and thermochemical analyses of the gas-adsorbed systems. Gas molecules interact with the membrane components through weak hydrogen bonds and exhibit low interaction energies, indicating physisorption of the gases. Gas adsorption energies are more negative than the mutual interaction energies of the gas molecules, ensuring effective gas adsorption by the membrane components. All the β-PVDF/IL systems have shown the highest and lowest affinity for CO2 and H2, respectively, leading to effective separation of CO₂ and H₂ from the other gases.

Machine Learning Meets with Metal Organic Frameworks for Gas Storage and Separation

The acceleration in design of new metal organic frameworks (MOFs) has led scientists to focus on high-throughput computational screening (HTCS) methods to quickly assess the promises of these fascinating materials in various applications. HTCS studies provide a massive amount of structural property and performance data for MOFs, which need to be further analyzed. Recent implementation of machine learning (ML), which is another growing field in research, to HTCS of MOFs has been very fruitful not only for revealing the hidden structure-performance relationships of materials but also for understanding their performance trends in different applications, specifically for gas storage and separation. In this review, we highlight the current state of the art in ML-assisted computational screening of MOFs for gas storage and separation and address both the opportunities and challenges that are emerging in this new field by emphasizing how merging of ML and MOF simulations can be useful.

Separation of C1/C3 binary organic gas mixtures via flexible nanoporous carbon molecular sieves: DFT calculations and MD simulations

The C₁/C₃ hydrocarbon gas separation characteristics of nanoporous carbon molecular sieves (CMS) are studied using DFT calculations and MD simulations. To efficiently separate the equimolar CH₄/C₃H₈ and CH₄/C₃H₆ gas mixtures, CNT gas transport channels are embed between the polyphenylene membranes which created structural deformation for both CNT and membrane. The adsorption and permeation of gas molecules via CMS and the effect of nanochannel density and electric field on gas selectivity are analyzed. In addition to the direct permeation, gas molecules that adsorbed on the NPG surface also making a significant contribution to the gas permeability comes from a surface mechanism. Results also uncovered that the gas selectivity is enhanced by the electric field along the + x and +y axes, whereas reduced by the electric field along the + z and -z axes. Plainly, this CMS provides a feasible way for the efficient separation of the C₁/C₃ organic gas mixtures.

Fabrication of waterproof gas separation membrane from plastic waste for CO2 separation

In this study, waste polystyrene (wPS) plastic was used to prepare gas-separation membranes with hot-pressing technology to reduce the accumulation of plastic waste. Polystyrene is a commonly used polymer for the production of plastic products, and it is also used in the synthesis of membranes for gas separation. Compared to the traditional synthesis process, hot-pressing is environmentally friendly because it does not require organic solvents. The mobility of the polymer chain and the integrity and free volume of the membrane are affected by the temperature, pressure, duration, and annealing environment of the hot-pressing process, thereby altering the performance of the membrane. Additionally, when the wPS contained polybutadiene, the gas separation membranes showed a selectivity of 17.14 for CO₂/N₂. The membranes also exhibited ideal waterproof performance when the membranes were operated under water pressures of 1-5 bar. Therefore, membranes derived from wPS through hot pressing are waterproof and can be used for gas separation. Furthermore, they are expected to maintain their separation performance in complex environments.

High performance compatible thiazole-based polymeric blend cellulose acetate membrane as selective CO2 absorbent and molecular sieve

Green blend membranes comprise of high thermal resistance ortho-linked thiazole-based polyimine (PM-4) including thioether linkage were fabricated in combination of glassy cellulose acetate (CA). The thermal stabilities of PMs were examined using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Morphological aspects and functional groups of the membranes were investigated via field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR) analysis respectively. X-ray diffraction (XRD) and mechanical strength were determined as well. The effects of polyimine content, pressure and temperature were studied on CO₂ permeability (P) and selectivity. The pressure changes revealed exponentially increases on CO₂ permeability by plasticization, facilitated transfer and solution-diffusion mechanisms, but decreases on CH₄ and N₂ permeations. Remarkable permeation (P =  3000 Barrer) of CA/PM-4 (1:3 % w/w) and ideal selectivity ratios of CO₂/N₂ = 59, CO₂/CH₄ = 33.7 were obtained at 3 bar and 35 °C versus neat CA membrane.

Enhancement in the selectivity of O2/N2 via ZIF-8/CA mixed-matrix membranes and the development of a thermodynamic model to predict the permeability of gases

Zeolitic imidazolate framework-8 (ZIF-8) has a sodalite topology. ZIF-8 is composed of zinc ion coordinated by four imidazolate rings. The pore aperture of ZIF-8 is 3.4 Å, which readily retains large gas molecules like N₂. In this work, mixed-matrix membranes (MMMs) have been fabricated by utilizing ZIF-8 and pristine cellulose acetate (CA) for O₂/N₂ separation. Membranes of pristine CA and MMMs of ZIF-8/CA at various ZIF-8 concentrations were prepared in tetrahydrofuran (THF). Permeation results of the fabricated membranes revealed increasing selectivity for O₂/N₂ with increasing pressure as well as ZIF-8/CA concentration up to 5% (w/w). The selectivity of O₂/N₂ increased 4 times for MMMs containing 5% (w/w) of ZIF-8/CA as compared with the pristine CA membrane. A thermodynamic model has also been developed to predict the permeability of gases through polymeric membranes. The results were compared with literature data as well as the pristine CA membrane produced in this work for model validation.

Experimental and numerical study of SO2 removal from a CO2/SO2 gas mixture in a Cu-BTC metal organic framework

The mechanism of SO₂ removal from a CO₂/SO₂ gas mixture in a copper benzene-1, 3, 5-tricarboxylate (Cu-BTC) material is investigated at the molecular level by the grand canonical Monte Carlo method. The effects of seven kinds of force-field relationships among CO₂, SO₂ and Cu-BTC on the selectivity for a SO₂/CO₂ gas mixture at different temperatures are studied in detail. The accuracy of the simulation model is validated by the experimental data. The results show that more SO₂ molecules are adsorbed than CO₂, and the electrostatic interactions involving SO₂ are more sensitive to temperature than CO₂ is. The multilayer desorption for SO₂ and CO₂ occurs in large-square channels. The effect of the electrostatic interactions involving SO₂ is stronger than the interactions of CO₂. The forms of CO₂ and SO₂ adsorption in Cu-BTC with electrostatic interactions are Cu²⁺∙∙∙OCO and Cu²⁺∙∙∙OSO, respectively.

A bio-inspired O2-tolerant catalytic CO2 reduction electrode

The electrochemical reduction of CO₂ to give CO in the presence of O₂ would allow the direct valorization of flue gases from fossil fuel combustion and of CO₂ captured from air. However, it is a challenging task because O₂ reduction is thermodynamically favored over that of CO₂. 5% O₂ in CO₂ near catalyst surface is sufficient to completely inhibit the CO₂ reduction reaction. Here we report an O₂-tolerant catalytic CO₂ reduction electrode inspired by part of the natural photosynthesis unit. The electrode comprises of heterogenized cobalt phthalocyanine molecules serving as the cathode catalyst with >95% Faradaic efficiency (FE) for CO₂ reduction to CO coated with a polymer of intrinsic microporosity that works as a CO₂-selective layer with a CO₂/O₂ selectivity of ∼20. Integrated into a flow electrolytic cell, the hybrid electrode operating with a CO₂ feed gas containing 5% O₂ exhibits a FE_CO of 75.9% with a total current density of 27.3 mA/cm² at a cell voltage of 3.1 V. A FE_CO of 49.7% can be retained when the O₂ fraction increases to 20%. Stable operation for 18 h is demonstrated. The electrochemical performance and O₂ tolerance can be further enhanced by introducing cyano and nitro substituents to the phthalocyanine ligand.

Porous metal-organic frameworks for gas storage and separation: Status and challenges

Gases are widely used as energy resources for industry and our daily life. Developing energy cost efficient porous materials for gas storage and separation is of fundamentally and industrially important, and is one of the most important aspects of energy chemistry and materials. Metal-organic frameworks (MOFs), representing a novel class of porous materials, feature unique pore structure, such as exceptional porosity, tunable pore structures, ready functionalization, which not only enables high density energy storage of clean fuel gas in MOF adsorbents, but also facilitates distinct host-guest interactions and/or sieving effects to differentiate different molecules for energy-efficient separation economy. In this review, we summarize and highlight the recent advances in the arena of gas storage and separation using MOFs as adsorbents, including progresses in MOF-based membranes for gas separation, which could afford broader concepts to the current status and challenges in this field.

Our journey of developing multifunctional metal-organic frameworks

Metal-organic frameworks (MOFs) are organic-inorganic hybrid solids constructed from the coordination interaction of metal ions/clusters with organic linkers, which currently represent one of the most rapidly expanding platforms for new functional materials. Based on well-established approaches, involving tuning the pore sizes, incorporation of functional sites and post-synthetic modification, the pore structures of MOFs can be readily controlled for multifunctional applications. In this brief review, we summarize and highlight our research progresses during our journey on developing functional MOFs for various applications including gas storage, gas separations, luminescent sensing, proton conduction, and molecular recognitions.

3-Aminopropyltriethoxysilane-aided cross-linked chitosan membranes for gas separation: grand canonical Monte Carlo and molecular dynamics simulations

Molecular simulations were performed to consider the structural and transport properties of chitosan/3-aminopropyltriethoxysilane (APTEOS) mixed matrix membranes (MMMs). In order to consider the presence of APTEOS content on the performances of membrane, various amounts of APTEOS were added to the polymeric matrix as a cross-linker. Structural characterizations such as radial distribution function (RDF), fractional free volume (FFV) and X-ray diffraction (XRD) were carried out on the simulated cells. Self-diffusivity and solubility of membranes were calculated using mean square displacement (MSD) and adsorption isotherms, respectively. Additionally, permeability and permselectivity of CO₂ and N₂ gases were calculated by grand canonical Monte Carlo and molecular dynamics methods. The system temperature was set to 298 K using a Nose-Hoover thermostat. According to the results, upon increasing APTEOS loading, CO₂ permeability increases until 10 wt.% loading. Then, by adding 20 wt.% of APTEOS, CO₂ permeability decreases, which could be related to higher crystallinity. XRD graphs indicated that the crystallinity decreased when adding 10 wt.% APTEOS, while higher APTEOS content (up to 20 wt.%) led to higher crystallinity percentage, consistent with permeability results. Compared to literature reports, the present simulation indicated higher accuracy for defining the structural and transport properties of APTEOS cross-linked chitosan MMMs. Graphical abstract 3-Aminopropyltriethoxysilane-aided cross-linked chitosan membranes for gasseparation.

Microporous Metal-Organic Framework with Dual Functionalities for Efficient Separation of Acetylene from Light Hydrocarbon Mixtures

Separating acetylene from light hydrocarbon mixtures like ethylene is a very important process for downstream industrial applications. Herein, we report a new MOF [CuL₂(SiF₆)] (UTSA-220, L = (1E,2E)-1,2-bis(pyridin-4-ylmethylene)hydrazine) with dual functionalities featuring optimal pore size with strong binding sites for acetylene. UTSA-220 exhibits apparently higher uptake capacity for C₂H₂ than those for other light hydrocarbons. The potential of this material for trace C₂H₂ removal from C₂H₄ has also been demonstrated by a dynamic breakthrough experiment performed with C₂H₂/C₂H₄ (1/99 v/v) under simulated industrial conditions. According to the dispersion-corrected density functional theory (DFT-D) simulation, SiF₆ ^2- and azine moieties serve as preferential binding sites for C₂H₂, indicating the feasibility of the dual functionalities incorporated in UTSA-220 for adsorbent-based C₂H₂ separations.

A Review on the Progress in Nanoparticle/C Hybrid CMS Membranes for Gas Separation

Carbon molecular sieve (CMS) membranes are novel materials derived from the pyrolysis of the polymeric precursors and have a well-developed ultra-microporous structure that can separate small gas pairs with minor difference in diameter, and thus exhibit higher gas permeability and selectivity than polymeric membranes. However, the gas permeability for traditional pure CMS membranes now cannot satisfy the requirements of commercial applications due to their disordered pore structure and high gas molecular diffusion resistance. Incorporating functional materials into membrane precursors to fabricate hybrid CMS membranes has been regarded as an effective way to tune the disordered pore structure of traditional pure CMS membranes, and thus to greatly improve their gas permeability. Many nanoparticles have been tested as the functional foreign materials to fabricate the hybrid CMS membranes with more developed microporous structure and enhanced gas separation performance. This review discusses the hybridized nanoparticle selection and effect of the species, quantities and particle sizes of the foreign materials on CMS membrane characteristics and performance. The function of the materials incorporated inside the hybrid CMS membranes is also analyzed. It is identified that preparation of hybrid CMS membranes provides a simple and convenient route to efficiently improve the trade-off relationship between permeability and selectivity, and to enable the construction of carbon-based composite materials with novel functionalities in membrane science.

A review of the innovative gas separation membrane bioreactor with mechanisms for integrated production and purification of biohydrogen

This review article focuses on an assessment of the innovative Gas Separation Membrane Bioreactor (GS-MBR), which is an emerging technology because of its potential for in-situ biohydrogen production and separation. The GS-MBR, as a special membrane bioreactor, enriches CO₂ directly from the headspace of the anaerobic H₂ fermentation process. CO₂ can be fed as a substrate to auxiliary photo-bioreactors to grow microalgae as a promising raw material for biocatalyzed, dark fermentative H₂-evolution. Overall, these features make the GS-MBR worthy of study. To the best of the authors' knowledge, the GS-MBR has not been studied in detail to date; hence, a comprehensive review of this topic will be useful to the scientific community.

Covalently Modified Graphene Oxide and Polymer of Intrinsic Microporosity (PIM-1) in Mixed Matrix Thin-Film Composite Membranes

In this study, mixed matrix membranes (MMMs) consisting of graphene oxide (GO) and functionalized graphene oxide (FGO) incorporated in a polymer of intrinsic microporosity (PIM-1) serving as a polymer matrix have been fabricated by dip-coating method, and their single gas transport properties were investigated. Successfully surface-modified GOs were characterized by Fourier transform infrared spectroscopy (FTIR), UV-Vis spectroscopy, Raman spectroscopy, scanning electron microscopy (SEM), and thermogravimetric analysis (TGA). The effect of FGO loading on MMM morphology and performance was investigated by varying the FGO content in polymer matrix from 9 to 84 wt.%. Use of high FGO content in the polymer matrix helped to reveal difference in interaction of functionalized fillers with PIM-1 and even to discuss the change of FGO stiffness and filler alignment to the membrane surface depending on functional group nature.

Development of LTA zeolite membrane from clay by sonication assisted method at room temperature for H2-CO2 and CO2-CH4 separation

In this work, sodium aluminosilicate zeolite powder and membranes were synthesized by ultrasonic irradiation at room temperature using montmorillonite clay as precursor material. For comparison, same zeolite powder and membranes were synthesized at 100 °C also. The synthesized zeolites were characterized by X-ray diffraction (XRD), infrared (IR) spectral analysis, and field-emission scanning electron microscopy (FESEM). XRD and IR results showed that phase pure mainly LTA phase was formed after 15 days of aging at room temperature. By using the zeolite powders as seeds, membranes were synthesized on clay alumina support tubes at room temperature and also at 100 °C. In both the cases membranes were formed on support surface. The membrane thickness was found to be 15 μm. The performances of the membranes were evaluated by single gas as well as mixture gas permeation measurement for H₂-CO₂ and CO₂-CH₄ respectively. The H₂-CO₂ and CO₂-CH₄ separation selectivity for the mixture gas of the membrane was found to 16.2 and 20.9 at room temperature respectively. To the best of our knowledge, there is no report of synthesis of zeolite membrane at room temperature using clay as raw materials. For the first time we have reported the synthesis of alumino-silicate zeolite membrane on clay alumina support surface using clay as starting material by sonochemical method at room temperature.

Production and application of O2 enriched air produced by fresh and salt water desorption in chemical plants

Oxygen enriched air intensifies oxidation processes since smaller reactors reach the same conversion of typical unit operations that employ simple air as reactant. However, the cost to produce pure oxygen or oxygen enriched air with traditional methods, i.e. cryogenic separation or membrane technologies, may be unaffordable. Here, we propose a new continuous technology for gas mixture separation, focusing on the production of oxygen enriched air as a case study. This operation is an absorption-desorption process that takes advantage of the higher oxygen solubility in water compared to nitrogen. In a pressurized solubilisation tank, water absorbs air. Subsequently, reducing pressure desorbs oxygen enriched air. PRO/II 9.3 (Simsci-Scheider Electrics) simulated, optimized, and calculated the capital and operative expenses of this technology. Moreover, we tested for the first time salt water instead of distilled water as appealing possibility for chemical plant near sea and ocean. We varied the inlet water flowrate between 5 and 15 m³/h. The optimum operative absortion unit pressure is 15-35 barg. After degassing, water may be recycled. With salt water, the extracted quantity of enriched air decreases compared with the desorption from fresh water (20% less), while the concentration of oxygen is independent from the salt concentration. The cost of enriched air at the optimum condition is 2-3.35 EUR/Nm³.

Gas Transport Properties of Polybenzimidazole and Poly(Phenylene Oxide) Mixed Matrix Membranes Incorporated with PDA-Functionalised Titanate Nanotubes

Functionalised titanate nanotubes (TiNTs) were incorporated to poly(5,5-bisbenzimidazole-2,2-diyl-1,3-phenylene) (PBI) or poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) for improving the interfacial compatibility between the polymer matrix and inorganic material and for altering the gas separation performance of the neat polymer membranes. Functionalisation consisted in oxidative polymerisation of dopamine-hydrochloride on the surface of non-functionalised TiNTs. Transmission electron microscopy (TEM) confirmed that a thin polydopamine (PDA) layer was created on the surface of TiNTs. 1.5, 3, 6, and 9 wt.% of PDA-functionalised TiNTs (PDA-TiNTs) were dispersed to each type of polymer matrix to create so-called mixed matrix membranes (MMMs). Infrared spectroscopy confirmed that -OH and -NH groups exist on the surface of PDA-TiNTs and that the nanotubes interact via H-bonding with PBI but not with PPO. The distribution of PDA-TiNTs in the MMMs was to some extent uniform as scanning electron microscope (SEM) studies showed. Beyond, PDA-TiNTs exhibit positive effect on gas transport properties, resulting in increased selectivities of MMMs. The addition of nanotubes caused a decrease in permeabilities but an increase in selectivities. It is shown that 9 wt.% of PDA-TiNTs in PBI gave a rise to CO₂/N₂ and CO₂/CH₄ selectivities of 112 and 63 %, respectively. In case of PPO-PDA-TiNT MMMs, CO₂/N₂ and CO₂/CH₄ selectivity increased about 25 and 17 %, respectively. Sorption measurement showed that the presence of PDA-TiNTs in PBI caused an increase in CO₂ sorption, whereas the influence on other gases is less noticeable.

Insights into the H2/CH4 Separation Through Two-Dimensional Graphene Channels: Influence of Edge Functionalization

A molecular simulation technique is employed to investigate the transport of H2/CH4 mixture through the two-dimensional (2D) channel between adjacent graphene layers. Pristine graphene membrane (GM) with pore width of 0.515~0.6 nm is found to only allow H2 molecules to enter rather than CH4, forming a molecular sieve. At pore widths of 0.64~1.366 nm, both H2 and CH4 molecules could fill into the GM channel, where the permeability of methane is more preferential than that of hydrogen with the largest CH4/H2 selectivity (1.89) at 0.728 nm. The edge functionalization by -H, -F, -OH, -NH2, and -COOH groups could significantly alter gas permeability by modifying the active surface area of the pore and tuning attractive and/or repulsive interaction with molecules at the entrance of channel. At the pore width of 0.6 nm, the H2 permeability of molecular sieve is enhanced by -H, -F, and -OH groups but restrained by -NH2, especially -COOH with a passing rate of zero. At pore widths of 0.64 and 0.728 nm, both -H and -F edge-functionalized GMs show a preferential selectivity of methane over hydrogen, while the favorable transport for GM-OH is changed from H2 molecules at 0.64 nm to CH4 molecules at 0.728 nm. For GM-NH2, it exhibits an excellent hydrogen molecular sieve at 0.64 nm and then turns into a significant H2/CH4 selectivity at 0.728 nm. Meanwhile, small H2 molecules start to enter the channel of GM-COOH at the pore width up to 0.728 nm. For the largest pore width of 1.336 nm, the influence of edge functionalization becomes small, and a comparable CH4/H2 selectivity is observed for all the considered membranes.