The degradation of high emulsified oil wastewater in an intermittently-aerated MBBR packed with magnetic polystyrene particles

This work aims to explore the effects of the magnetic polystyrene particles (MPS) on contaminants removal of the high emulsified oil wastewater. 26 days intermittently-aerated progress illustrated that COD removal efficiency and the resistance to the shock loading was promoted in the presence of MPS. Gas chromatography (GC) results also indicated that MPS enhanced the number of organic species reduced. According to the cyclic voltammetry test, conductive MPS appeared special redox performance which was considered could to facilitate the extracellular electron transfer. Furthermore, MPS dosing accelerated the electron-transporting system (ETS) activity by 24.91% compared the control. Based on the superior performance above, the conductivity of MPS is considered to be responsible for the enhanced organic removal efficiency. Moreover, the high-throughput sequencing displayed that electroactive Cloacibacterium and Acinetobacter accounted for a higher proportion in the MPS reactor. Additionally, Porphyrobacter and Dysgonomonas which were capable of degrading organics were also enriched more by MPS. To sum up, MPS is a promising additive to enhance the organic substances removal for the high emulsified oil wastewater.

Wildfire loss of forest soil C and N: Do pre-fire treatments make a difference?

Losses of C and N from the forest floor and top 20-cm of soil were estimated following separate severe wildfires at two Long-Term Soil Productivity sites in the Sierra Nevada of California, USA. Experimental treatments applied 20 years prior to the wildfires included factorial combinations of 1) organic matter (OM) removal following clear-cut harvesting (SO, stem only harvest, WTH, whole-tree harvest, and WTH + FF, WTH plus the forest floor removal), 2) soil compaction (three levels of intensity), and 3) with and without understory vegetation control. Wildfires caused complete losses of the forest floor in all treatments and also oxidized varying portions of OM in the topsoil. As such, pre-fire forest floor measures were used as an estimate of forest floor C and N loss, and post-fire soil measures of C and N were compared to pre-fire soil data to estimate of mineral soil losses. Averaged over all treatments, the less-productive site that also had lesser accumulations of detritus (Wallace) lost 35.1 Mg C ha-1, or 25 % of its original C stores, while the more-productive site with greater detritus (Rogers) lost 18.4 Mg C ha-1, or 20 % of its original. The SO treatments that left harvest residue on site ended up with much greater losses of C: 36 % versus 15 and 17 % for WTH and WTH + FF, respectively. The SO also yielded the largest losses (25-30 %) of C in the top 10-cm of soil. The other treatments had smaller or inconsistent effects (understory vegetation control) or no effect (soil compaction). Our results suggest that potential benefits from SO by leaving residue on site to soil C and N accumulation can also be readily eliminated by wildfire which commonly occurs at these fire-prone forest ecosystems.

Rapid and efficient removal of organic matter from sewage sludge for extraction of microplastics

Microplastic pollution is recognized as an emerging global issue; however, no standardized method for the extraction of these pollutants from the environment currently exists and existing methods are ineffective for specific environmental matrices. An appropriate organic matter removal method is essential for the extraction of microplastics from organic-rich sludge to minimize interference during their identification and enhance compatibility of the identification steps. The present study aimed to establish an effective technique for the digestion of organic matter-rich sludge using hydrogen peroxide and Fenton's reagent at varying temperatures, times, and concentrations of an iron catalyst. The organic matter removal efficiency of the five protocols utilized varied from 81.5 % to 87.1 %. Polymers such as polyvinyl chloride (PVC), high density polyethylene (HDPE), low density polyethylene (LDPE), polypropylene (PP), and polystyrene (PS) retained most of their physical and chemical properties after the treatments, with minor changes in the surface area, weight, and FTIR spectra properties. Polyethylene terephthalate (PET), PET fiber, polyamide (PA) fiber, and polymethyl methacrylate (PMMA) fiber were significantly degraded via treating with H₂O₂ at 50 °C for 24 h. Protocol 4, treating with Fenton's reagent (H₂O₂ (30 %) + (0.05 M) FeSO₄.7H₂O) at 50 °C for 1 h is proposed as a rapid and effective method for the removal of organic matter from sludge. In addition to its rapidity, this method minimally impacts most polymers, and its high organic matter removal efficiency is associated with a significant reduction of suspended solids in sludge. The present study provides a validated approach that facilitates as an effective organic removal step during the extraction of MPs in sludge.

Approach to a fungal treatment of a biologically treated landfill leachate

White-rot fungi (WRF) have the ability to synthetize extracellular enzymes that could degrade recalcitrant pollutants. The aim of this work was to evaluate the use of P. chrysosporium to treat a biologically and physically pre-treated landfill leachate which high load of refractory compounds (COD>1000 mg/L, BOD₅<50 mg/L) in order to reduce COD and colour. Batch tests were carried out at 26 °C and 135 rpm for 15 days. The soluble chemical oxygen demand (sCOD), soluble biological oxygen demand (sBOD₅) and colour, as well as the lignin peroxidase (LiP) and manganese peroxidase (MnP) enzymatic activities were analysed. Besides, the effects of different operating conditions, i.e., pH control, permeate dilution and supplementation, on treatment efficacy were investigated. The control of pH was shown to be key for fungal treatment. In addition, it was found that the addition of carbon and nitrogen sources improved the enzymatic synthesis and the removals of sCOD and colour. Data here obtained open the possibility of using fungi for reducing the amount of recalcitrant pollutants still present in treated landfill leachates or similar effluents.

A first attempt for using of combined sorption and anaerobic processes for handling source separated human urine

Processing human urine with clinoptilolite results in a solid phase upon which majority of nutrients are concentrated, which may be used as fertilizer; in addition to a liquid residue to be disposed of which is saline, rich in organics and contains residual nutrients. Despite several work regarding nutrients recovery from human urine, the fate of organic matter in the liquid residue is yet to be revealed. This study aims to investigate the combination of sorption and anaerobic processing (ANA) to accomplish concurrent nutrient recovery, and organic matter removal from hydrolyzed human urine (HHU) for environmental protection. Fixed bed clinoptilolite columns were used for nutrient recovery from HHU and an anaerobic expanded granular sludge bed reactor (AnEGSB) was used for removal of organic matter from residue of the former process. Furthermore, the effluent of AnEGSB was subjected to post treatment using stage-wise sorption to enhance the effluent quality before disposal. Majority of nutrients were removed by the sorption process with 80% of ammonium and almost all of phosphorus. Sorption removed 35% of orgnic matter while ANA was responsible for the rest. Post treatment helped to polish the quality of the AnEGSB effluent to the permissible level of domestic wastewater discharge standards of EU.With the proposed combination, almost 100% of nitrogen and phosphorus were recovered for further use as fertilizer providing benefits for sustainability. Also, 97% of organic matter could be removed from HHU to provide environmental protection, which was accompanied by methane (CH₄) production of 0.4 L CH₄/day which is equivalent to 0.113 L CH₄/g COD removed. Successful implementation of the proposed combination helps improve management of domestic wastewater.

Enhanced treatment of organic matter in slaughter wastewater through live Bacillus velezensis strain using nano zinc oxide microsphere

Slaughter wastewater is an important and wide range of environmental issues, and even threaten human health through meat production. A high efficiency and stability microsphere-immobilized Bacillus velezensis strain was designed to remove organic matter and inhibit the growth of harmful bacteria in process of slaughter wastewater. Bacillus velezensis was immobilized on the surface of sodium alginate (SA)/Polyvinyl alcohol (PVA)/Nano Zinc Oxide (Nano-ZnO) microsphere with the adhesion to bio-carrier through direct physical adsorption. Results indicated that SA/PVA/ZnO and SA/ZnO microspheres could inhibit E.coli growth with adding 0.15 g/L nano-ZnO and not affect Bacillus velezensis strain, and the removal the chemical oxygen demand (COD) rates of SA/PVA/ZnO microsphere immobilized cells are 16.99%, followed by SA/ZnO (13.69%) and free bacteria (7.61%) from 50% concentration slaughter wastewater within 24 h at 37 °C, pH 7.0, and 120 rpm, a significant difference was found between the microsphere and control group. Moreover, when the processing time reaches 36 h, COD degradation of SA/PVA/ZnO microsphere is obviously higher than other groups (SA/PVA/ZnO:SA/ZnO:control vs 18.535 : 15.446: 10.812). Similar results were obtained from 30% concentration slaughter wastewater. Moreover, protein degradation assay was detected, and there are no significant difference (SA/PVA/ZnO:SA/ZnO:control vs 35.4 : 34.4: 36.0). The design of this strategy could greatly enhance the degradation efficiency, inhibit the growth of other bacteria and no effect on the activity of protease in slaughter wastewater. These findings suggested that the nano-ZnO hydrogel immobilization Bacillus velezensis system wastewater treatment is a valuable alternative method for the remediation of pollutants from slaughter wastewater with a novel and eco-friendly with low-cost investment as an advantage.

Preparation of biological samples for microplastic identification by Nile Red

Many methods have been used to isolate and identify microplastics from biological matrices. In biological samples, Nile Red can stain undigested residues, such as fats, soaps, and gels formed during organic matter removal, hindering the identification of fluorescent microplastics (≥2 μm). Thus, adjustments on sample preparation (e.g., fat removal) are required for the accurate identification of Nile Red stained microplastics. Multiples tests allowed to identify that digestion with 10% KOH at 60 °C for 24 h, followed by treatments with boiling water, acetone, and staining, produced good results in fourteen biological samples, including vertebrates and invertebrates. Digestion efficiencies were 94-100%, except for feces, which were 87%. Recovery rates of spiked microplastics were 97-100%, and few effects were observed in the infrared spectra and carbonyl index of seven polymers, with only the occasional yellowing suggesting surface changes. Filtration rates were improved by reducing the amount of sample. Small fluorescent microplastics could be identified in all samples under the microscope. Overall, the proposed method was efficient in removing natural organic matter from biological samples for Nile Red staining, requiring minimal sample handling, improving sample throughput, and allowing quantification of fluorescent microplastics in biological samples.

Treatment of slaughterhouse wastewater by electrocoagulation and electroflotation as a combined process: process optimization through response surface methodology

The contamination of water with organic compounds has become an increasing concern in today's world. The cost-effective and sustainable treatment of industrial wastewaters is a major challenge. Advanced treatment techniques such as electrocoagulation-electroflotation offer economic and reliable solutions for the treatment of industrial wastewater. In this study, the electrocoagulation-electroflotation method was investigated for the simultaneous removal of chemical oxygen demand, total phosphorus, total Kjeldahl nitrogen, and color via response surface methodology. Factors such as electrode combination (Fe and Al), current density (10-20 mA/cm²), pH (3.0-9.0), and electrode distance (1-3 cm) were investigated in the treatment of wastewater to obtain maximum treatment efficiency. It was determined that chemical oxygen demand, total Kjeldahl nitrogen, total phosphorus, and color removal reached up to 94.0%, 77.5%, 97.0%, and 99.0%, respectively. Treatment costs were found as $0.71 with the Al-Fe electrode combination.

Using excitation-emission matrix fluorescence to evaluate the performance of water treatment plants for dissolved organic matter removal

This study is aimed at assessing the performance of water treatment plants (both wastewater and drinking water treatment plants) for dissolved organic matter (DOM) removal using excitation-emission matrix fluorescence (EEMF) as the monitoring technique. The influent from the wastewater treatment plant (WWTP) of Burgos (Spain) is characterized from the presence of protein-like peaks (T1 and T2) and humic-like peaks (A and C), T2 and A showing the highest fluorescence intensity. The percentages of total removal in the effluent were in the following order: peak T1 (65%) > peak A (45%) > peak C (34%) > peak T2 (26%). The humic-like peaks were the most removed at the primary sedimentation stage, whereas peak T1 was by far the most removed in the biological reactor. Protein-like peaks T1 and T2 experienced a slight increase in the final effluent in comparison to their fluorescence at the previous stage (the exit of the biological reactor), an increase that can be explained by the release of SMP (soluble microbial products) from the biomass in the secondary clarifier. A poor correlation was obtained between peak T2 fluorescence and COD, BOD (r² = 0.34-0.38). The natural water from the Úzquiza reservoir in Burgos (Spain) is characterized by the only presence of humic substances: a majority peak A (fulvic-like) and a weak peak C (humic-like). The whole fluorescent DOM was removed by coagulation-flocculation but a low fluorescence peak T2 appeared at the final stage, coming from protein-like SMPs released by the biomass attached to the filters.

Isolation and Extraction of Microplastics from Environmental Samples: An Evaluation of Practical Approaches and Recommendations for Further Harmonization

Researchers have been identifying microplastics in environmental samples dating back to the 1970s. Today, microplastics are a recognized environmental pollutant attracting a large amount of public and government attention, and in the last few years the number of scientific publications has grown exponentially. An underlying theme within this research field is to achieve a consensus for adopting a set of appropriate procedures to accurately identify and quantify microplastics within diverse matrices. These methods should then be harmonized to produce quantifiable data that is reproducible and comparable around the world. In addition, clear and concise guidelines for standard analytical protocols should be made available to researchers. In keeping with the theme of this special issue, the goals of this focal point review are to provide researchers with an overview of approaches to isolate and extract microplastics from different matrices, highlight associated methodological constraints and the necessary steps for conducting procedural controls and quality assurance. Simple samples, including water and sediments with low organic content, can be filtered and sieved. Stepwise procedures require density separation or digestion before filtration. Finally, complex matrices require more extensive steps with both digestion and density adjustments to assist plastic isolation. Implementing appropriate methods with a harmonized approach from sample collection to data analysis will allow comparisons across the research community.

Deciphering of organic matter and nutrient removal and bacterial community in three sludge treatment wetlands under different operating conditions

Sludge treatment wetlands (STWs) can effectively stabilize sludge, but the microbial community structure in this process is not well characterized. The purpose of this study was to investigate the characteristics of organic matter and nutrient removal and bacterial community in sludge treatment wetlands for treating sewage sludge. Three STWs units included unit STW1 with aeration tubes, unit STW2 with aeration tubes and reed planting and unit STW3 with reed planting. The degradation of organic matter and nutrient, sludge dewatering performance and microbial community dynamics in STWs were examined in feeding and resting periods. Our results showed that during the entire process of the experiment, total solids (TS) in STWs increased to 24-31%, volatile solids (VS) in STWs reduced to 43-47%, while the total kjeldahl nitrogen (TKN) and total phosphorous (TP) concentrations in STWs decreased to 25.1-35.5 mg/g d. w and 5.4-6.2 mg/g d. w. However, the removal efficiencies of organic matter and nutrient in STWs in the feeding period were higher than those in the resting period. Meanwhile, unit STW2 has the best removal performance in organic matter and nutrients during the whole experiment. Microbial community analysis using Illumina MiSeq sequencing technology showed that growth of plants in STWs improved bacterial diversity and richness which corresponded to high removal rates of organic matter and nutrient. Besides, principal coordinate analysis (PCoA) showed that the bacterial community composition in STWs obviously altered between the feeding and the resting periods.

Simultaneous removal of organic matters and nutrients from high-strength wastewater in constructed wetlands followed by entrapped algal systems

The present work designs a low-cost biological treatment strategy consisting of constructed wetlands (CWs) followed by entrapped algae (EA) for removing nutrients (PO₄^3-, NO₃^-, and NH₄⁺) and organic matters from high-strength wastewater. The CWs are efficient means for organic pollutant removal but face challenges in nutrient removal. Algae have a high growth rate and nutrient uptake capabilities from wastewater. The severe challenge that limits the use of algae for nutrient removal from wastewater is its post-treatment separation from wastewater. This work presents a strategy to address the described problems of CWs and algae-based system. It also assesses the performance of the system using synthetic wastewater. A combined system of CW followed by EA (CW-EA) was able to treat 86.0% of phosphate, 95.0% of nitrate, 74.0% of ammonium, and 87.0% of chemical oxygen demand (COD) from high-strength wastewater.

National series of long-term intensive harvesting trials in Pinus radiata stands in New Zealand: Initial biomass, carbon and nutrient pool data

Global interest in addressing knowledge gaps relating to the effect of forest harvest intensity on soil fertility and long-term site productivity has resulted in the installation of numerous experiments, including Long-Term Site Productivity (LTSP) trials. To explore this issue in the context of the New Zealand planted forest estate, six LTSP sites were established from 1985 to 1994 across differing climate and soil conditions, then subjected to varying levels of organic matter removal during the harvest of the trees. Here we present data describing live above ground, forest floor and mineral soil carbon and nutrient pools immediately prior to, and following, harvesting at each site. Harvest residue management practices employed included the removal of stem only, whole tree, whole tree plus forest floor, whole tree plus forest floor and topsoil, and the addition of double harvest slash material. The data provides an understanding of biomass, carbon and nutrient pools at harvest and the impact of different harvest removal treatments on these pools. With the maturation of the trees at the LTSP sites, the data acquires even greater future value by enabling changes in soil properties to be quantified and correlated to variations in the biological properties at the site, including site productivity and critical microbial parameters. Overall, these data sets comprise a foundation for New Zealand to address the question – can the productivity of intensively managed planted Pinus radiata be maintained or enhanced through the judicious management of organic matter and nutrient pools over successive growing and harvesting cycles?

Identifying a quick and efficient method of removing organic matter without damaging microplastic samples

Natural organic matter may confound the detection of microplastics, requiring a removal step. However, most available protocols are long and lack information on removal efficiency and polymer degradation. Thus, we have determined the digestion efficiency (%) for a pool of organic matter (algae, driftwood, feathers, fish muscle, paraffin, palm oil) for five digestion solutions, hydrogen peroxide (H₂O₂), hydrogen peroxide with iron catalyst (H₂O₂ + Fe), potassium hydroxide (KOH), nitric acid (HNO₃), and sodium dodecyl sulphate (SDS), under two temperatures (room temperature at 25 °C, 50 °C) and two periods (1, 6 h). H₂O₂ + Fe and KOH at 50 °C for 1 h had the highest digestion efficiencies, of 65.9% and 58.3% respectively (mostly limited by driftwood and paraffin). Further testing revealed that H₂O₂ + Fe is more appropriate for plant material and KOH for animal tissue. Weight loss (%), Fourier transform infrared spectrometry and carbonyl index of 9 virgin and 6 weathered polymers (polyethylene, polypropylene, polystyrene, polyethylene terephthalate, polyvinyl chloride, cellulose acetate, nylon) revealed that only identification of cellulose acetate was hindered. Filters were also tested revealing that quartz and glass fibre filters are resistant to these protocols. Thus, a digestion protocol based on H₂O₂ + Fe or KOH at 50 °C for 1 h may be used on microplastic samples.

Simultaneous hydrogen production and pollutant removal from olive mill wastewaters using electrohydrolysis process

Management of olive mill wastewaters is one of the most challenging environmental issue in Mediterranean countries due to its high organic load, color, presence of phenolic compounds and need for high energy cost. Performance of electrohydrolysis (EH) process in terms of removal of organic compounds, detoxification and discoloration of olive mill wastewater (OMW) with simultaneous energy production in the hydrogen gas form has been investigated using aluminum electrodes. Different reaction times and electric potential gradients have been tested in order to determine the most effective conditions for removal of pollutants. The optimum reaction time and current were determined as 8 h and 8 V, respectively. Under these conditions, removal efficiencies for tCOD, suspended solids, color and phenol were obtained as 73%, 84%, 91% and 75%, respectively. At the end of the operating period of 8 h, 1037 ml hydrogen gas was obtained. The results show that electrohydrolysis process can be used as an alternative solution for the management of OMW and the process can be upgraded with a better reactor design or combined with different treatment processes to achieve a better effluent quality to meet discharge standards.

Treatment of old landfill leachate with high ammonium content using aerobic granular sludge

Background

Aerobic granular sludge has become an attractive alternative to the conventional activated sludge due to its high settling velocity, compact structure, and higher tolerance to toxic substances and adverse conditions. Aerobic granular sludge process has been studied intensively in the treatment of municipal and industrial wastewater. However, information on leachate treatment using aerobic granular sludge is very limited.

Methods

This study investigated the treatment performance of old landfill leachate with different levels of ammonium using two aerobic sequencing batch reactors (SBR): an activated sludge SBR (ASBR) and a granular sludge SBR (GSBR). Aerobic granules were successfully developed using old leachate with low ammonium concentration (136 mg L⁻¹ NH₄⁺-N).

Results

The GSBR obtained a stable chemical oxygen demand (COD) removal of 70% after 15 days of operation; while the ASBR required a start-up of at least 30 days and obtained unstable COD removal varying from 38 to 70%. Ammonium concentration was gradually increased in both reactors. Increasing influent ammonium concentration to 225 mg L⁻¹ N, the GSBR removed 73 ± 8% of COD; while COD removal of the ASBR was 59 ± 9%. The GSBR was also more efficient than the ASBR for nitrogen removal. The granular sludge could adapt to the increasing concentrations of ammonium, achieving 95 ± 7% removal efficiency at a maximum influent concentration of 465 mg L⁻¹ N. Ammonium removal of 96 ± 5% was obtained by the ASBR when it was fed with a maximum of 217 mg L⁻¹ NH₄⁺-N. However, the ASBR was partially inhibited by free-ammonia and nitrite accumulation rate increased up to 85%. Free-nitrous acid and the low biodegradability of organic carbon were likely the main factors affecting phosphorus removal.

Conclusion

The results from this research suggested that aerobic granular sludge have advantage over activated sludge in leachate treatment.

Anaerobic co-digestion of vegetable waste and swine wastewater in high-rate horizontal reactors with fixed bed

Considering the high waste generation that comes from agriculture and livestock farming, as well as the demand for natural gas, it is necessary to develop sustainable technologies which can reduce environmental impact. There is no available literature on the use of high-rate horizontal anaerobic reactors with fixed bed (HARFB) and continuous feed for the co-digestion of vegetable wastes (VW) and swine wastewater (SW). The aim of this work was to evaluate the reactor performance in terms of methane production, organic matter consumption, and removal of total and thermotolerant coliforms under different proportions of SW and VW, and organic loading rates (OLR) of 4.0, 5.2 and 11.0g COD (Ld)(-)(1). The mixture of SW and VW in the proportions of 90:10, 80:20 and 70:30 (SW:VW) with those OLRs provided great buffering capacity, with partial alkalinity reaching 3552mgL(-1), thereby avoiding the inhibition of methane production by volatile fatty acids produced during the fermentation process. Higher proportions of VW and higher OLR improved volumetric methane production with a maximum value of 1.08LCH4 (Ld)(-)(1), organic matter removal rates up to 98% and total and thermotolerant coliform removal rates of 99% were also observed.

Removing organic and nitrogen content from a highly saline municipal wastewater reverse osmosis concentrate by UV/H2O2-BAC treatment

Reverse osmosis (RO) concentrate (ROC) streams generated from RO-based municipal wastewater reclamation processes pose potential health and environmental risks on their disposal to confined water bodies such as bays. A UV/H2O2 advanced oxidation process followed by a biological activated carbon (BAC) treatment was evaluated at lab-scale for the removal of organic and nutrient content from a highly saline ROC (TDS 16 g L(-1), EC 23.5 mS cm(-1)) for its safe disposal to the receiving environment. Over the 230-day operation of the UV/H2O2-BAC process, the colour and UV absorbance (254 nm) of the ROC were reduced to well below those of the influent to the reclamation process. The concentrations of DOC and total nitrogen (TN) were reduced by approximately 60% at an empty bed contact time (EBCT) of 60 min. The reduction in ammonia nitrogen by the BAC remained high under all conditions tested (>90%). Further investigation confirmed that the presence of residual peroxide in the UV/H2O2 treated ROC was beneficial for DOC removal, but markedly inhibited the activities of the nitrifying bacteria (i.e., nitrite oxidising bacteria) in the BAC system and hence compromised total nitrogen removal. This work demonstrated that the BAC treatment could be acclimated to the very high salinity environment, and could be used as a robust method for the removal of organic matter and nitrogen from the pre-oxidised ROC under optimised conditions.

Co-treatment of landfill leachate and domestic wastewater using a submerged aerobic biofilter

This study used a pilot-scale submerged aerobic biofilter (SAB) to evaluate the co-treatment of domestic wastewater and landfill leachate that was pre-treated by air stripping. The leachate tested volumetric ratios were 0, 2, and 5%. At a hydraulic retention time of 24 h, the SAB was best operated with a volumetric ratio of 2% and removed 98% of the biochemical oxygen demand (BOD), 80% of the chemical oxygen demand (COD) and dissolved organic carbon (DOC), and 90% of the total suspended solids (TSS). A proposed method, which we called the "equivalent in humic acid" (Eq.HA) approach, indicated that the hardly biodegradable organic matter in leachate was removed by partial degradation (71% of DOC Eq.HA removal). Adding leachate at a volumetric ratio of 5%, the concentration of the hardly biodegradable organic matter was decreased primarily as a result of dilution rather than biodegradation, which was confirmed by Fourier transform infrared (FTIR) spectroscopy. The total ammoniacal nitrogen (TAN) was mostly removed (90%) by nitrification, and the SAB performances at the volumetric ratios of 0 and 2% were equal. For the three tested volumetric ratios of leachate (0, 2, and 5%), the concentrations of heavy metals in the treated samples were below the local limits.