Synthesis of TiO2 Nanobelt Bundles Decorated with TiO2 Nanoparticles and Aggregates and Their Use as Anode Materials for Lithium-Ion Batteries

TiO₂ nanobelt bundles decorated with TiO₂ aggregates were prepared using an easy and scalable hydrothermal method at various temperatures (170, 190, 210, and 230 °C). It was demonstrated that the synthesis temperature is a key parameter to tune the number of aggregates on the nanobelt surface. Prepared TiO₂ aggregates and nanobelt bundles were used to design anode materials in which the aggregates regulated the pore size and connectivity of the interconnected nanobelt bundle structure. A galvanostatic technique was employed for the electrochemical characterization of TiO₂ samples. Using TiO₂ as a model material due to its small volume change during the cycling of lithium-ion batteries (LIBs), the relationship between the morphology of the anode materials and the capacity retention of the LIBs on cycling is discussed. It was clearly found that the size and connectivity of the pores and the specific surface area had a striking impact on the Li insertion behavior, lithium storage capability, and cycling performance of the batteries. The initial irreversible capacity was shown to increase as the specific surface area increased. As the pore size increased, the ability of the mesoporous anatase to release strain was stronger, resulting in better cycling stability. The TiO₂ powder prepared at a temperature of 230 °C displayed the highest discharge and charge capacities (203.3 mAh/g and 140.8 mAh/g) and good cycling stability.

Visible-light responsive ZnSe-anchored mesoporous TiO2heterostructures for boosted photocatalytic reduction of Cr(VI)

The accumulation of Cr(VI) ions in water can cause serious influences on the environment and human health. This work reports a humble synthesis of ZnSe nanoparticles anchored to the sol-gel prepared TiO₂for visible-light-driven photocatalytic reduction of Cr(VI) ions. The 7.9 nm ZnSe nanoparticles were attached to TiO₂surfaces at a content of 1.0-4.0 wt% as experiential by TEM investigation. The designed nanocomposite unveiled mesostructured surfaces exhibiting surface areas of 176-210 m²g^-1. The impregnation of ZnSe amended the visible-light absorption of TiO₂due to the bandgap decrease from 3.14 to 2.90 eV. The photocatalytic reduction of Cr(VI) applying the optimized portion of 3.0 wt% ZnSe/TiO₂was achieved at 177μmol min^-1. This photocatalytic activity is higher than the common Degussa P25 and pristine TiO₂by 20 and 30 times, respectively. The improved performance is signified by the efficient interfacial separation of charge carriers by the introduction of ZnSe. This innovative ZnSe/TiO₂has also shown photocatalytic stability for five consecutive runs.

Compact SnO2/Mesoporous TiO2 Bilayer Electron Transport Layer for Perovskite Solar Cells Fabricated at Low Process Temperature

Charge transport layers have been found to be crucial for high-performance perovskite solar cells (PSCs). SnO₂ has been extensively investigated as an alternative material for the traditional TiO₂ electron transport layer (ETL). The challenges facing the successful application of SnO₂ ETLs are degradation during the high-temperature process and voltage loss due to the lower conduction band. To achieve highly efficient PSCs using a SnO₂ ETL, low-temperature-processed mesoporous TiO₂ (LT m-TiO₂) was combined with compact SnO₂ to construct a bilayer ETL. The use of LT m-TiO₂ can prevent the degradation of SnO₂ as well as enlarge the interfacial contacts between the light-absorbing layer and the ETL. SnO₂/TiO₂ bilayer-based PSCs showed much higher power conversion efficiency than single SnO₂ ETL-based PSCs.

Enhanced Light Absorption by Facile Patterning of Nano-Grating on Mesoporous TiO2 Photoelectrode for Cesium Lead Halide Perovskite Solar Cells

CsPbIBr₂, a cesium-based all-inorganic halide perovskite (CsPe), is a very promising alternative material to mainstream organic–inorganic hybrid halide perovskite (HPe) materials owing to its exceptional moisture stability, thermal stability, and light stability. However, because of the wide band gap (2.05 eV) of CsPbIBr₂, it has a low power conversion efficiency (PCE), which hinders its application in highly efficient solar cells. In this study, a facile nanoimprinted one-dimensional grating nanopattern (1D GNP) formation on mesoporous TiO₂ (mp-TiO₂) photoelectrodes was introduced to improve the effective light utilization and enhance the performance of CsPbIBr₂ perovskite solar cells (PSCs). The 1D GNP structure on the mp-TiO₂ layer increases the light absorption efficiency by diffracting the unabsorbed light into the active mp-TiO₂ and CsPbIBr₂ layers as well as increasing the charge separation and collection due to the extended interfacial contact area between the mp-TiO₂ and CsPbIBr₂ layers. Consequently, both the current density (J_SC) and the fill factor (FF) of the fabricated cells improved, leading to over a 20% enhancement in the solar cell’s PCE. Thus, this periodic grating structure, fabricated by simple nanoimprinting, could play an important role in the large-scale production of highly efficient and cost-effective Cs-based PSCs.

Solar-Powered Photodegradation of Pollutant Dyes Using Silver-Embedded Porous TiO2 Nanofibers

Titanium dioxide (TiO₂) nanomaterials have been ubiquitously investigated as a photocatalyst for organic contaminant treatment in wastewater due to their exemplary semiconductor properties. However, their huge band gap remains a barrier for visible light absorption, limiting their utility in practical applications. The incorporation of noble metals in the TiO₂ scaffold would help mitigate the problem via plasmonic resonance enhancements. Silver (Ag) is the chosen noble metal as it is relatively cheap and has great plasmonic effects. In this study, the use of electrospun Ag-embedded TiO₂ nanofibers as a photocatalyst is shown to be effective in decomposing rhodamine B and methyl orange dyes under a solar simulator in 3 h, which is more efficacious as opposed to pristine TiO₂ nanofibers. This showcases the potential of a simple and economic wastewater treatment system for the removal of organic pollutants.

Driving the Interfacial Ion-Transfer Kinetics by Mesoporous TiO2 Spheres for High-Performance Aqueous Zn-Ion Batteries

The aqueous zinc-ion batteries (ZIBs) have been considered as a promising energy storage device. However, the ion transfer at the Zn metal anode-electrolyte interface is limited by the sluggish kinetics resulting in high interface resistance. Herein, mesoporous TiO₂ (m-TiO₂) is coated on the Zn foil (Zn-TiO₂) driving the ion's faster transfer to reduce interface resistance (70.1 Ω vs 799.3 Ω of bare Zn). The lower interface resistance is ascribed to shortening the ion transfer path provided by the mesoporous structure and the smaller Zn²⁺ absorption energy barrier of the surface of the Zn-TiO₂ anode as well as the unobstructed ion transfer path at the crystal planes (100) of TiO₂, which have been supported by the density functional theory (DFT) calculation and experiments. Therefore, the Zn-TiO₂ anodes in the symmetrical cells display a low voltage hysteresis (36.5 mV) and long-term cycling stability (500 h at 4.4 mA cm^-2). Especially, the Zn-TiO₂/MnO₂ full cells show superior cycling performance with a high capacity of 269.8 mAh g^-1 after 50 cycles at 0.2 A g^-1 and 210.9 mAh g^-1 after 1000 cycles at 0.5 A g^-1. The analysis of ion-transfer kinetics at the interface provides deep enlightenment and reference for the study of the metal anodes.

Comparative Catalytic Properties of Supported and Encapsulated Gold Nanoparticles in Homocoupling Reactions

This report describes strategies to increase the reactive surfaces of integrated gold nanoparticles (AuNPs) by employing two different types of host materials that do not possess strong electrostatic and/or covalent interactive forces. These composite particles are then utilized as highly reactive and recyclable quasi-homogeneous catalysts in a C-C bond forming reaction. The use of mesoporous TiO₂ and poly(N-isopropylacrylamide), PNIPAM, particles allows for the formation of relatively small and large guest AuNPs and provides the greatly improved stability of the resulting composite particles. As these AuNPs are physically incorporated into the mesoporous TiO₂ (i.e., supported AuNPs) and PNIPAM particles (i.e., encapsulated AuNPs), their surfaces are maximized to serve as highly reactive catalytic sites. Given their increased physicochemical properties (e.g., stability, dispersity, and surface area), these composite particles exhibit notably high catalytic activity, selectivity, and recyclability in the homocoupling of phenylboronic acid in water and EtOH. Although the small supported AuNPs display slightly faster reaction rates than the large encapsulated AuNPs, the apparent activation energies (E_a) of both composite particles are comparable, implying no obvious correlation with the size of guest AuNPs under the reaction conditions. Investigating the overall physical properties of various composite particles and their catalytic functions, including the reactivity, selectivity, and E_a, can lead to the development of highly practical quasi-homogeneous catalysts in green reaction conditions.

Effects of the Brookite Phase on the Properties of Different Nanostructured TiO2 Phases Photocatalytically Active Towards the Degradation of N-Phenylurea

Different sol-gel synthesis methods were used to obtain four nanostructured mesoporous TiO2 samples for an efficient photocatalytic degradation of the emerging contaminant N-phenylurea under either simulated solar light (1 Sun) or UV light. Particularly, two TiO2 samples were obtained by means of as many template-assisted syntheses, whereas other two TiO2 samples were obtained by a greener template-free procedure, implying acidic conditions and, then, calcination at either 200 °C or 600 °C. In one case, anatase was obtained, whereas in the other three cases mixed crystalline phases were obtained. The four TiO2 samples were characterized by X-ray powder diffraction (followed by Rietveld analysis); Transmission Electron Microscopy; N2 adsorption/desorption at -196 °C; Diffuse Reflectance UV/Vis spectroscopy and ζ-potential measurements. A commercial TiO2 powder (i. e., Degussa P25) was used for comparison. Differences among the synthesized samples were observed not only in their quantitative phase composition, but also in their nanoparticles morphology (shape and size), specific surface area, pore size distribution and pHIEP (pH at isoelectric point), whereas the samples band-gap did not vary sizably. The samples showed different photocatalytic behavior in terms of N-phenylurea degradation, which are ascribed to their different physico-chemical properties and, especially, to their phase composition, stemming from the different synthesis conditions.

Using Soft Polymer Template Engineering of Mesoporous TiO2 Scaffolds to Increase Perovskite Grain Size and Solar Cell Efficiency

The mesoporous (meso)-TiO₂ layer is a key component of high-efficiency perovskite solar cells (PSCs). Herein, pore size controllable meso-TiO₂ layers are prepared using spin coating of commercial TiO₂ nanoparticle (NP) paste with added soft polymer templates (SPT) followed by removal of the SPT at 500 °C. The SPTs consist of swollen crosslinked polymer colloids (microgels, MGs) or a commercial linear polymer (denoted as LIN). The MGs and LIN were comprised of the same polymer, which was poly(N-isopropylacrylamide) (PNIPAm). Large (L-MG) and small (S-MG) MG SPTs were employed to study the effect of the template size. The SPT approach enabled pore size engineering in one deposition step. The SPT/TiO₂ nanoparticle films had pore sizes > 100 nm, whereas the average pore size was 37 nm for the control meso-TiO₂ scaffold. The largest pore sizes were obtained using L-MG. SPT engineering increased the perovskite grain size in the same order as the SPT sizes: LIN < S-MG < L-MG and these grain sizes were larger than those obtained using the control. The power conversion efficiencies (PCEs) of the SPT/TiO₂ devices were ∼20% higher than that for the control meso-TiO₂ device and the PCE of the champion S-MG device was 18.8%. The PCE improvement is due to the increased grain size and more effective light harvesting of the SPT devices. The increased grain size was also responsible for the improved stability of the SPT/TiO₂ devices. The SPT method used here is simple, scalable, and versatile and should also apply to other PSCs.

Surface Engineering of Low-Temperature Processed Mesoporous TiO2 via Oxygen Plasma for Flexible Perovskite Solar Cells

A major problem in the application of mesoporous TiO₂ as an electron transport layer for flexible perovskite solar cells is that a high-temperature sintering process is required to remove organic additives from the TiO₂ layer. A facile oxygen plasma process is herein demonstrated to fabricate mesoporous-structured perovskite solar cells with significant photovoltaic performance at low temperatures. When the low-temperature processed TiO₂ layer is modified via oxygen plasma, the organic additives in the TiO₂ layer that hinder the charge transport process are successfully decomposed. The oxygen plasma treatment improves the wettability and infiltration of the perovskite layer and also passivates the oxygen vacancy related traps in TiO₂. Hence, the oxygen plasma treatment evidently enhances charge extraction and transport, thereby improving photovoltaic performance and decreasing hysteresis.

Investigation of Well-Defined Pinholes in TiO2 Electron Selective Layers Used in Planar Heterojunction Perovskite Solar Cells

The recently introduced perovskite solar cell (PSC) technology is a promising candidate for providing low-cost energy for future demands. However, one major concern with the technology can be traced back to morphological defects in the electron selective layer (ESL), which deteriorates the solar cell performance. Pinholes in the ESL may lead to an increased surface recombination rate for holes, if the perovskite absorber layer is in contact with the fluorine-doped tin oxide (FTO) substrate via the pinholes. In this work, we used sol-gel-derived mesoporous TiO2 thin films prepared by block co-polymer templating in combination with dip coating as a model system for investigating the effect of ESL pinholes on the photovoltaic performance of planar heterojunction PSCs. We studied TiO2 films with different porosities and film thicknesses, and observed that the induced pinholes only had a minor impact on the device performance. This suggests that having narrow pinholes with a diameter of about 10 nm in the ESL is in fact not detrimental for the device performance and can even, to some extent improve their performance. A probable reason for this is that the narrow pores in the ordered structure do not allow the perovskite crystals to form interconnected pathways to the underlying FTO substrate. However, for ultrathin (~20 nm) porous layers, an incomplete ESL surface coverage of the FTO layer will further deteriorate the device performance.

Novel Route to Obtain Carbon Self-Doped TiO2 Mesoporous Nanoparticles as Efficient Photocatalysts for Environmental Remediation Processes under Visible Light

Titanium dioxide materials were synthesized using two different methods. The samples were characterized by X-ray diffraction (XRD), UV-Visible diffusion reflectance spectroscopy (UV-Vis DR), Raman spectroscopy, N₂ adsorption/desorption, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron spectroscopy (TEM) and X-ray photoelectron spectroscopy (XPS). Although both kind of materials were found to have mesoporous structure and anatase crystalline phase, one of them was obtained from a synthesis method that does not involve the use of surfactants, and therefore, does not require calcination at high temperatures. This implies that the synthesized solid was self-doped with carbon species, coming only from the same source used for titanium. Then, the relationship between the presence of these species, the final calcination temperature, and the photocatalytic activity of the solids was studied in terms of the degradation and mineralization of an Acid Orange 7 aqueous solution, under visible radiation. A photosensitizing effect caused by the non-metal presence, that allows the solid to extend its absorption range, was found. Hence, a novel route to prepare C-modified photoactive mesoporous TiO₂, simpler and cheaper, where neither a template nor an external carbon source is used, could be performed.

Enhancing the Photovoltaic Performance of Perovskite Solar Cells Using Plasmonic Au@Pt@Au Core-Shell Nanoparticles

Au@Pt@Au core-shell nanoparticles, synthesized through chemical reduction, are utilized to improve the photoelectric performance of perovskite solar cells (PSCs) in which carbon films are used as the counter electrode, and the hole-transporting layer is not used. After a series of experiments, these Au@Pt@Au core-shell nanoparticles are optimized and demonstrate outstanding optical and electrical properties due to their local surface plasmon resonance and scattering effects. PSC devices containing 1 wt.% Au@Pt@Au core-shell nanoparticles have the highest efficiency; this is attributable to their significant light trapping and utilization capabilities, which are the result of the distinctive structure of the nanoparticles. The power conversion efficiency of PSCs, with an optimal content of plasmonic nanoparticles (1 wt.%), increased 8.1%, compared to normal PSCs, which was from 12.4% to 13.4%; their short-circuit current density also increased by 5.4%, from 20.5 mA·cm-2 to 21.6 mA·cm-2. The open-circuit voltages remaining are essentially unchanged. When the number of Au@Pt@Au core-shell nanoparticles in the mesoporous TiO2 layer increases, the photovoltaic parameters of the former shows a downward trend due to the recombination of electrons and holes, as well as the decrease in electron transporting pathways.

Facile Interfacial Engineering of Mesoporous TiO2 for Low-Temperature Processed Perovskite Solar Cells

The mesoporous TiO2 nanoparticle-based scaffold structure is the best electron transport layer (ETL) for perovskite solar cells (PSCs) and is still used in most PSCs with optimal photovoltaic characteristics. However, the high sintering temperature of TiO2 nanoparticles required to remove binders from the TiO2 paste limits PSC application to flexible electronics. In this study, a simple interface modification process involving ethanol rinsing is developed to enhance the photovoltaic characteristics of low-temperature processed PSCs. This easy and fast technique could enable remarkable performance by PSCs by significantly increasing the fill factor and current density, leading to a power conversion efficiency more than four times that of untreated solar cells.

Improving the Performance of Dye-Sensitized Solar Cells

Dye-sensitized solar cells have been investigated intensively during the last three decades. Nevertheless, there are still many aspects to be explored to further improve their performance. Dye molecules can be modified endlessly for better performance. For instance, steric groups can be introduced to slow down recombination reactions and avoid unfavorable aggregation. There is a need for more optimal dye packing on the mesoporous TiO₂ surface to increase light absorption and promote a better blocking effect. Novel redox mediators and HTMs are key elements to reach higher performing DSC as they can offer much higher output voltage than the traditional triiodide/iodide redox couple.

Flexible Mixed-Potential-Type (MPT) NO₂ Sensor Based on An Ultra-Thin Ceramic Film

A novel flexible mixed-potential-type (MPT) sensor was designed and fabricated for NO₂ detection from 0 to 500 ppm at 200 °C. An ultra-thin Y₂O₃-doped ZrO₂ (YSZ) ceramic film 20 µm thick was sandwiched between a heating electrode and reference/sensing electrodes. The heating electrode was fabricated by a conventional lift-off process, while the porous reference and the sensing electrodes were fabricated by a two-step patterning method using shadow masks. The sensor’s sensitivity is achieved as 58.4 mV/decade at the working temperature of 200 °C, as well as a detection limit of 26.7 ppm and small response time of less than 10 s at 200 ppm. Additionally, the flexible MPT sensor demonstrates superior mechanical stability after bending over 50 times due to the mechanical stability of the YSZ ceramic film. This simply structured, but highly reliable flexible MPT NO₂ sensor may lead to wide application in the automobile industry for vehicle emission systems to reduce NO₂ emissions and improve fuel efficiency.

Ferroelectric BiFeO3 as an Oxide Dye in Highly Tunable Mesoporous All-Oxide Photovoltaic Heterojunctions

As potential photovoltaic materials, transition-metal oxides such as BiFeO₃ (BFO) are capable of absorbing a substantial portion of solar light and incorporating ferroic orders into solar cells with enhanced performance. But the photovoltaic application of BFO has been hindered by low energy-conversion efficiency due to poor carrier transport and collection. In this work, a new approach of utilizing BFO as a light-absorbing sensitizer is developed to interface with charge-transporting TiO₂ nanoparticles. This mesoporous all-oxide architecture, similar to that of dye-sensitized solar cells, can effectively facilitate the extraction of photocarriers. Under the standard AM1.5 (100 mW cm^-2 ) irradiation, the optimized cell shows an open-circuit voltage of 0.67 V, which can be enhanced to 1.0 V by tailoring the bias history. A fill factor of 55% is achieved, which is much higher than those in previous reports on BFO-based photovoltaic devices. The results provide here a new viable approach toward developing highly tunable and stable photovoltaic devices based on ferroelectric transition-metal oxides.

Intrinsic and Extrinsic Stability of Formamidinium Lead Bromide Perovskite Solar Cells Yielding High Photovoltage

We report on both the intrinsic and the extrinsic stability of a formamidinium lead bromide [CH(NH₂)₂PbBr₃ = FAPbBr₃] perovskite solar cell that yields a high photovoltage. The fabrication of FAPbBr₃ devices, displaying an outstanding photovoltage of 1.53 V and a power conversion efficiency of over 8%, was realized by modifying the mesoporous TiO₂-FAPbBr₃ interface using lithium treatment. Reasons for improved photovoltaic performance were revealed by a combination of techniques, including photothermal deflection absorption spectroscopy (PDS), transient-photovoltage and charge-extraction analysis, and time-integrated and time-resolved photoluminescence. With lithium-treated TiO₂ films, PDS reveals that the TiO₂-FAPbBr₃ interface exhibits low energetic disorder, and the emission dynamics showed that electron injection from the conduction band of FAPbBr₃ into that of mesoporous TiO₂ is faster than for the untreated scaffold. Moreover, compared to the device with pristine TiO₂, the charge carrier recombination rate within a device based on lithium-treated TiO₂ film is 1 order of magnitude lower. Importantly, the operational stability of perovskites solar cells examined at a maximum power point revealed that the FAPbBr₃ material is intrinsically (under nitrogen) as well as extrinsically (in ambient conditions) stable, as the unsealed devices retained over 95% of the initial efficiency under continuous full sun illumination for 150 h in nitrogen and dry air and 80% in 60% relative humidity (T = ∼60 °C). The demonstration of high photovoltage, a record for FAPbBr₃, together with robust stability renders our work of practical significance.

Ordered Macro/Mesoporous TiO2 Hollow Microspheres with Highly Crystalline Thin Shells for High-Efficiency Photoconversion

Well ordered, uniform 3D open macro/mesoporous TiO2 hollow microspheres with highly crystalline anatase thin shells have been successfully synthesized by a simple solvent evaporation-driven confined self-assembly method. The 3D open macro/mesoporous TiO2 hollow microspheres show high energy-conversion efficiency (up to 9.5%) and remarkable photocatalytic activity (with photodegradation of 100% for methylene blue in 12 min under UV light irradiation).

General strategy to synthesize uniform mesoporous TiO2/graphene/mesoporous TiO2 sandwich-like nanosheets for highly reversible lithium storage

Uniform oxide deposition on graphene to form a sandwich-like configuration is a well-known challenge mainly due to their large lattice mismatches and poor affinities. Herein, we report a general strategy to synthesize uniform mesoporous TiO2/graphene/mesoporous TiO2 sandwich-like nanosheets (denoted as G@mTiO2), which cannot be achieved by conventional one-pot synthetic methods. We show that by rational control of hydrolysis and condensation of Ti precursors in a slow way, GO sheets can be conformably coated by amorphous TiO2 shells, which then can be facilely transformed into the well-defined G@mTiO2 nanosheets by annealing. This amorphous-to-crystalline strategy conveniently allows bypassing strain fields that would inevitably arise if direct growth of mesoporous anatase shells on graphene. As distinct from the most common structures of graphene-based composites (mixed, wrapped, or anchored models), the resultant materials display a uniform sandwich-like configuration: few-layer graphene conformably encapsulated by mesoporous TiO2 shells. This new G@mTiO2 nanosheet exhibits ultrathin nature (∼34 nm), small size and high crystalline nanocrystals (∼6 nm), high surface areas (∼252 m(2)/g) and uniform mesopores (∼3.4 nm). We further show that the thickness of mesoporous TiO2 shells can be facilely adjusted as desired by controlling the ammonia content, and this facile strategy can be easily extended to design other oxide/graphene/oxide sandwich-like materials. More importantly, we showcase the benefits of the resultant G@mTiO2 nanosheets as anodes in lithium ion batteries: they deliver an extra high capacity, an excellent high-rate capability, and long cycle life.

Mesoporous TiO₂ spheres interconnected by multiwalled carbon nanotubes as an anode for high-performance lithium ion batteries

We report on the excellent electrochemical response of lithium ion batteries that use a composite material comprised of mesoporous titanium dioxide (MTO) spheres and multiwalled carbon nanotubes (MWCNTs) for the anode. The composite structure was synthesized via a combined sol-gel and solvothermal method, and the batteries exhibited unprecedented discharge capacity, cycling stability, and reversibility when compared to those based on commercially available TiO2 nanopowders and mesoporous TiO2 spheres. The inclusion of the composite structure resulted in an improvement in electronic and ionic conductivity, a larger surface area, and a colossal number of open channels in the synthesized structure that allowed for lithium ion intercalation. We achieved a Coulombic efficiency of nearly 100% and a discharge capacity as high as 316 mA h g(-1) at a rate of C/5, which is 1.9 times higher than that which is practically attainable with TiO2. Moreover, we observed a capacity loss of only 3.1% after 100 cycles, which indicates that the synthesized structure has a highly stable nature.

Improved morphology control using a modified two-step method for efficient perovskite solar cells

A two-step wet chemical synthesis method for methylammonium lead(II) triiodide (CH3NH3PbI3) perovskite is further developed for the preparation of highly reproducible solar cells, with the following structure: fluorine-doped tin oxide (FTO)/TiO2 (compact)/TiO2 (mesoporous)/CH3NH3PbI3/spiro-OMeTAD/Ag. The morphology of the perovskite layer could be controlled by careful variation of the processing conditions. Specifically, by modifying the drying process and inclusion of a dichloromethane treatment, more uniform films could be prepared, with longer emission lifetime in the perovskite material and longer electron lifetime in solar cell devices, as well as faster electron transport and enhanced charge collection at the selective contacts. Solar cell efficiencies up to 13.5% were obtained.

Parameters Affecting I-V Hysteresis of CH3NH3PbI3 Perovskite Solar Cells: Effects of Perovskite Crystal Size and Mesoporous TiO2 Layer

Current-voltage (I-V) characteristics of CH3NH3PbI3 perovskite solar cells are studied using a time-dependent current response with stepwise sweeping of the bias voltage. Compared with the crystalline Si solar cell showing time-independent current at a given bias voltage, the perovskite solar cells exhibit time-dependent current response. The current increases with time and becomes steady at forward scan from short-circuit to open-circuit, whereas it is decayed and saturated with time at reverse scan from open-circuit to short-circuit. Time-dependent current response eventually leads to I-V hysteresis depending on the scan direction and the scan rate. Crystal size of CH3NH3PbI3 and the mesoporous TiO2 (mp-TiO2) film are found to influence I-V hysteresis, where the I-V hysteresis is alleviated as crystal size increases and in the presence of mp-TiO2. The capacitance observed at low frequency (0.1 to 1 Hz), associated with dipole polarization, tends to diminish as size of perovskite and mp-TiO2 layer thickness increases, which suggests that the origin of hysteresis correlates to the capacitive characteristic of CH3NH3PbI3 and the degree of hysteresis depends strongly on perovskite crystal size and mesoporous TiO2 layer.