The effect of implant diameter, restoration design, and occlusal table variations on screw loosening of posterior single-tooth implant restorations

The purpose of this study was to (1) determine in vitro the effect of narrowing the buccolingual width of the occlusal table on the untightening torque required to loosen gold prosthetic screws after subjecting implants and implant-supported restorations to occlusal loads, and (2) to compare the incidence of screw loosening and values of untightening torque of the screws among crowns supported by 1 wide-diameter as opposed to 2 standard implants after loading in vitro. The restorations were divided into 4 groups (group 1, a narrow crown supported by one 5-mm wide-diameter implant; group 2, a narrow crown supported by 2 standard 3.75-mm-diameter implants; group 3, a wide crown supported by one 5-mm wide-diameter implant; and group 4, a wide crown supported by 2 standard 3.75-mm-diameter implants). A custom-designed chewing machine was used to simulate the grinding phase of the masticatory cycle and lateral excursions. The crowns were subjected to a 6-kg load for 16660 cycles over 5.5 hours and were loaded at the outer and inner inclines and cusp tips with an untightening loading pattern. The untightening torque was measured for the gold screws in the different groups before and after loading at 4 different locations for 8 cycles on the simulated chewing machine. A 1-way analysis of variance indicated a significant difference (P < .001) among the test groups. Pairwise multiple comparison tests (Scheffe) were carried out on mean "change scores." Group 3 was significantly different from the other groups, which were not significantly different from each other. Restoring missing molars with 1 wide-diameter implant had a greater incidence of screw loosening as compared with 2 implants. Narrowing the occlusal table of the restoration is critical when using 1 implant to support a missing molar. The untightening torque of gold screws was not affected by changing the width of the occlusal table of crowns supported by 2 implants.

A 48-month multicentric clinical investigation: implant design and survival

This report is based on a total of 2,955 implants of 6 different designs, randomized and placed in 829 patients and followed for 48 months. Implant failure was defined as nonintegration at uncovering or removal due to mobility, persistent pain, infection, and evidence of radiographic bone loss. Failures were reported for 3 phases of treatment: implant placement to uncovering (phase 1), uncovering to loading (phase 2), and postloading (phase 3). Differences in survival were compared with Kaplan-Meier survival curves. The maxillary single tooth application resulted in 95.2% survival for the hydroxyapatite-coated grooved implants. In the maxillary completely edentulous application, survival of hydroxyapatite grooved and screw implants were considerably better compared with the titanium screw implants. The hydroxyapatite-coated cylinder had better survival than the titanium basket and screw designs in the mandibular completely edentulous application. The hydroxyapatite-coated cylinder and grooved implants in the maxillary posterior partially edentulous application had similar survival rates. The survival of the hydroxyapatite-coated cylinder exceeded that of the titanium basket in mandibular posterior partially edentulous applications. Analyses by phase of treatment indicated a pattern of early failure for nonhydroxyapatite-coated implants compared with hydroxyapatite-coated implants. The implant with the highest survival at all phases of treatment was the hydroxyapatite-coated press-fit cylinder. Two hydroxyapatite-coated implant designs performed well in the challenging posterior maxillary region.

Optimum aerobic volume control based on continuous in-line oxygen uptake monitoring

Dynamic adaptation of the aerated volume to changing load conditions is essential to maximise the nitrogen removal performance and to minimise energy consumption. A control strategy is presented which provides optimum aerobic volume control (OAV-control concept) based on continuous in-line oxygen uptake monitoring. For ammonium concentrations below 1 mg/l the oxygen uptake rate shows a strong and almost linear dependency on the ammonium concentration. Therefore, the oxygen uptake rate is an ideal indicator for the nitrification performance in activated sludge systems. The OAV-control concept provides dynamic variation of the minimum aerobic volume required for complete nitrification and therefore maximises the denitrification performance. In-line oxygen uptake monitoring is carried out by controlling the oxygen concentration in a continuous aerated zone of the aeration tank and measuring the total air flow to the aeration tank. The total air flow to the aeration tank is directly proportional to the current oxygen uptake rate and can therefore be used as an indicator for the required aerobic volume. The instrumentation requirements for installation of the OAV-control are relatively low, oxygen sensors in the aeration tank and an on-line air flow measurement are needed. This enables individual control of aeration tanks operated in parallel at low investment costs. The OAV-control concept is installed at the WWTP Linz-Asten (1 Mio PE) and shows very good results. Full scale results are presented.

Influence of changes of the wastewater composition on the applicability of UV-absorption measurements at combined sewer overflows

The applicability of UV-absorption measurements at combined sewer overflows was investigated under different storm water conditions. Three specific rainfall events of different intensity, different duration and different intervals between the events were investigated. An individual evaluation of each single event resulted in an acceptable correlation between the UV absorption and the pollution measured as COD. A combined evaluation of the different events exhibited a very poor correlation which could not be used as pollution control parameter. Since the calibration procedure of the spectrometer used was not flexible enough to distinguish between different wastewater matrices from the different storm events the applicability of this type of spectrometer for the control of storm water overflows is questionable.

Progress in sensor technology--progress in process control? Part II: results from a simulation benchmark study

To show the impact of sensor behaviour on the control result, four strategies for aeration control are tested using different sensor characteristics. It is demonstrated, on the one hand, how an increasing response time will limit the achievable control quality and, on the other hand, how a given sensor characteristic can be taken into account for the controller design. The presented tests show that an improvement potential by control for WWTPs is available but this potential is limited compared to proper DO control with fixed set-points. To activate this control potential, sufficient control authority must be available and a careful control design is required. It can be shown that using feedback control, sensors with a small response time have significant advantages compared to conventional sensors. Using feed forward control, the improvement potential by control is considerably higher and additionally, the sensor delay can be integrated into the controller design. The presented discussion is based on simulation studies performed on a standardised benchmark case. For these tests it was necessary to include sensor models into the simulation model. It can be stated that the usage of sensor models is necessary for the application of dynamic simulation for the design and evaluation of WWTP control and in general to achieve realistic results.

Progress in sensor technology--progress in process control? Part 1: sensor property investigation and classification

To ensure correctly operating control systems, the measurement and control equipment in WWTPs must be mutually consistent. The dynamic simulation of activated sludge systems could offer a suitable tool for designing and optimising control strategies. Ideal or simplified sensor models represent a limiting factor for comparability with field applications. More realistic sensor models are therefore required. Two groups of sensor models are proposed on the basis of field and laboratory tests: one for specific sensors and another for a classification of sensor types to be used with the COST simulation benchmark environment. This should lead to a more realistic test environment and allow control engineers to define the requirements of the measuring equipment as a function of the selected strategy.

Thoracoscopic fluorescence diagnosis (TFD) of pleural malignancies: experimental studies

BACKGROUND

Fluorescence diagnosis (FD) using the photosensitiser 5-aminolaevulinic acid (ALA) was experimentally combined with conventional video assisted thoracic surgery (VATS) to improve tumour staging in advanced lung cancer with pleural tumour spread.

METHODS

A disseminated pleural carcinosis affecting the entire pleural cavity was induced by inoculation of human adenocarcinoma cells in nude rats. After 5-7 weeks of tumour growth the animals were randomised into six groups with different photosensitisation parameters. Pleural lavage was performed either with 1.5% or 3.0% ALA solution. Photosensitisation times varied were 2, 4, or 6 hours. Conventional white light VATS was first performed to evaluate tumour growth in the pleural cavity. Fluorescence illumination of the light source, the D-light, was then used to examine the site for additional tumours which were previously invisible. The tumour fluorescence intensity was measured spectrometrically and compared with normal tissue.

RESULTS

Compared with conventional white light VATS alone, thoracoscopic fluorescence diagnosis (TFD) detected up to 30% additional pleural malignant lesions. The highest diagnostic sensitivity was reached 6 hours after 3.0% ALA pleural lavage. Photosensitiser accumulation in the tumour, measured indirectly by spectrometry, was up to 11 times higher than in normal tissue.

CONCLUSIONS

TFD increases sensitivity of VATS for tumour staging. It may prevent unnecessary thoracotomies in cancer patients and facilitate surgical planning.

The ankylos endosseous dental implant: assessment of stability up to 18 months with the Periotest

Osseointegration is an ongoing histometric process that may vary during clinical function. The implant must be stable at uncovering, which reflects the status of bone-implant interface. The physiology of bone healing associated with endosseous implants suggests that this process occurs between 8 and 12 months, and Periotest values (PTVs) tend to reflect changes in the stability of the bone-implant interface. Stability generally increases gradually from the time of uncovering to an optimal PTV that occurs at a point close to 12 months. This stable interface must remain intact for long-term clinical survival. Rapid development of this optimal PTV is highly desirable in order to prevent premature overloading of the bone-implant interface. The Ankylos implant is a new screw-type implant design in which the thread pitch and length vary to maximize trabecular bone contact. The purpose of this report is to evaluate to 18 months the stability (PTVs) of this implant design. More than 457 implants were placed and followed for a period of 18 months by the multicentered, multidisciplinary Ankylos Implant Clinical Research Group (AICRG). Implant stability (PTVs) was assessed using the Periotest at abutment connection and at 3, 6, 9, 12, and 18 months after uncovering. The Periotest values for all implants rapidly reached an optimal status between uncovering (-3.1 PTVs) and 3 months (-3.4 PTVs). This rapid increase in stability has not previously been reported for other implant designs. The mandibular arch was more negative (-3.8 PTVs) at uncovering as compared with the PTVs for the maxillary arch (-1.7 PTVs). Negative PTVs were recorded (1) as length and diameter increased, (2) as bone density increased, (3) in certain jaw regions, (4) as the number of implants/case increased, and (5) for implants stabile at placement. The Ankylos screw implant design produced rapid stabilization 3 months after uncovering.

Reduction-oxidation control of beta-sheet assembly in genetically engineered silk

Genetically engineered spider dragline silk protein was modified to incorporate methionines flanking the beta-sheet forming polyalanine regions. The methionines could be selectively chemically oxidized and reduced. This chemical change altered the bulkiness and charge of the sulfhydryl groups, and in turn, the beta-sheet forming tendencies of the polyalanine domains and solubility of the protein. The genes encoding these redesigned proteins were constructed, cloned and expressed in Escherichia coli. In the reduced state (beta-mercaptoethanol) the approximately 25 kDa protein behaved similarly to native spider dragline silk, crystallizing into beta-sheets based on diffraction analysis and appearing fibrous by TEM. The addition of the methionines into the consensus dragline silk sequence did not disrupt the normal macromolecular assembly behavior of the protein. In the oxidized state (phenacyl bromide) the protein did not form beta-sheet crystals and appeared morphologically featureless based on TEM. A reduction in beta-strand content was also observed upon oxidation based on FTIR and TEM analysis and confirmed by X-ray diffraction analysis. To further confirm changes in assembly behavior observed for the recombinant protein containing the methionines, a model peptide with the same repeat amino acid sequence was synthesized and characterized. Shifts in molecular weight, observed by MALDI, along with corresponding changes in crystallinity, by electron diffraction, agreed with the changes expected on activation and deactivation of the redox trigger. These results support the use of a redox trigger as a useful feature with which to control the assembly of beta-sheet forming proteins.

Treatment of easily biodegradable wastewater avoiding bulking sludge

The presence of easily degradable compounds from food industries frequently leads to bulking problems. The paper describes a new process that has been developed for a dairy in Austria. Because of the increase in production the treatment plant receiving the wastewater up to now was not able to handle the increased loads. Therefore detailed studies for treatment alternatives have been undertaken which led to a completely new concept. The excess sludge of the urban treatment plant is contacted with the concentrated dairy waste in a separate contact tank. In this tank the easily degradable substrate from the industrial waste is mainly adsorbed to the biological sludge and after a mechanical dewatering transferred to the anaerobic digester where it yields an increased gas production. The filtrate of the dewatering process is completely free from biodegradable material and can without danger of bulking be fed to the aeration tank. The process has been in operation for more than one year and has fulfilled all expectations.

In-situ measurement of ammonium and nitrate in the activated sludge process

A new in-situ probe is presented for the continuous measurement of ammonium and nitrate in wastewater. It requires no sample preparation and is installed directly in the process liquid. This new low-cost probe significantly reduces investment and operating costs and requires minimum maintenance. The paper describes the sensor principle and test results from three different probe locations: the primary clarifier effluent, the activated sludge tank and the nitrifying biofilter influent. Reference measurements were carried out by means of conventional analyzers with ultrafiltration, an in-situ UV spectrometer for the nitrate and laboratory analysis of spot and 2h-composite samples. The aim of the study was to investigate the operational reliability and accuracy of the new probe and the expenditure required for its maintenance and calibration. The tests showed that the new probe performed very well overall and required minimum maintenance. Some problems were observed during the biofilter plant test. They are assumed to be related to substantial changes in the wastewater composition.

Two stage activated sludge plants--influence of different operational modes on sludge bulking and nitrification

Conventional two stage activated sludge plants often lack sufficient nutrient removal performance due to substrate limitation for denitrification in the second stage. For the extension of the Vienna Main WWTP a two stage concept has been developed and tested by means of a pilot plant (scale 1:10.000). The new concept enables the operation of two different modes: In BYPASS-mode a portion of the primary clarifier effluent is fed directly to the second stage; the HYBRID-mode includes the exchange of mixed liquor between the two stages; over the course of the pilot plant investigations it turned out that nutrient removal is strongly increased in comparison to conventional two stage mode, but the two modes of operation lead to different results with regard to the sludge quality and the nitrification performance. BYPASS mode yields a higher SVI in both stages and a lower nitrification performance in comparison to HYBRID mode. This is caused by the negative influence of the primary effluent on the biocoenosis of the second stage. Additionally, the reduced sludge loading of the first stage in this mode results in a higher sludge age which favours the growth of filaments (Microthrix and Nocardia). In HYBRID-mode the higher load of the first stage results in a lower sludge age, fatty components are metabolized and incorporated in the sludge, thus, the growth of filaments is significantly reduced. Additionally, nitrification inhibiting substances are degraded in the first stage, which results in a higher nitrification performance in the second stage.

F-ATPase: forced full rotation of the rotor despite covalent cross-link with the stator

In ATP synthase (F(O)F(1)-ATPase) ion flow through the membrane-intrinsic portion, F(O), drives the central "rotor", subunits c(10)epsilongamma, relative to the "stator" ab(2)delta(alphabeta)(3). This converts ADP and P(i) into ATP. Vice versa, ATP hydrolysis drives the rotation backwards. Covalent cross-links between rotor and stator subunits have been shown to inhibit these activities. Aiming at the rotary compliance of subunit gamma we introduced disulfide bridges between gamma (rotor) and alpha or beta (stator). We engineered cysteine residues into positions located roughly at the "top," "center," and "bottom" parts of the coiled-coil portion of gamma and suitable residues on alpha or beta. This part of gamma is located at the center of the (alphabeta)(3) domain with its C-terminal part at the top of F(1) and the bottom part close to the F(O) complex. Disulfide bridge formation under oxidizing conditions was quantitative as shown by SDS-polyacrylamide gel electrophoresis and immunoblotting. As expected both the ATPase activities and the yield of rotating subunits gamma dropped to zero when the cross-link was formed at the center (gammaL262C <--> alphaA334C) and bottom (gammaCys(87) <--> betaD380C) positions. But much to our surprise disulfide bridging impaired neither ATP hydrolysis activity nor the full rotation of gamma and the enzyme-generated torque of oxidized F(1), which had been engineered at the top position (gammaA285C <--> alphaP280C). Apparently the high torque of this rotary engine uncoiled the alpha-helix and forced amino acids at the C-terminal portion of gamma into full rotation around their dihedral (Ramachandran) angles. This conclusion was supported by molecular dynamics simulations: If gammaCys(285)-Val(286) are attached covalently to (alphabeta)(3) and gammaAla(1)-Ser(281) is forced to rotate, gammaGly(282)-Ala(284) can serve as cardan shaft.

African-European differences in the capacity of T-cell cytokine production

Regional differences in immune responsiveness have been studied by comparing the frequency of cytokine producing T cells in healthy African children and adults and their age-matched European counterparts. By use of flow cytometry for the intracellular detection of cytokines an overall expansion of CD4+ and CD8+ T cells producing the Type 1 cytokines interleukin (IL)-2 and interferon (IFN)-gamma was observed in adults when compared with children, giving credit to the cumulative effect of contacts with environmental antigens. The CD4+ cells expressing the Type 2 cytokines IL-4 and IL-13, however, increased only in Africans, probably reflecting continuously present challenges with antigens that preferentially drive Type 2 responses. A striking increased frequency of both Type 1 and Type 2 cytokines producing T cells was found in African adults when compared with their European counterparts. The quantitative and qualitative regional differences in immune reactivity are likely to be of significance for all immune intervention strategies, especially for the design of vaccines.

Photosynthetic water oxidation in Synechocystis sp. PCC6803: mutations D1-E189K, R and Q are without influence on electron transfer at the donor side of photosystem II

The oxygen-evolving manganese cluster (OEC) of photosynthesis is oxidised by the photochemically generated primary oxidant (P(+*)(680)) of photosystem II via a tyrosine residue (Y(Z), Tyr161 on the D1 subunit of Synechocystis sp. PCC6803). The redox span between these components is rather small and probably tuned by protonic equilibria. The very efficient electron transfer from Y(Z) to P(+*)(680) in nanoseconds requires the intactness of a hydrogen bonded network involving Y(Z), D1-His190, and presumably D1-Glu189. We studied photosystem II core particles from photoautotrophic mutants where the residue D1-E189 was replaced by glutamine, arginine and lysine which were expected to electrostatically differ from the glutamate in the wild-type (WT). Surprisingly, the rates of electron transfer from Y(Z) to P(+*)(680) as well as from the OEC to Y(ox)(Z) were the same as in the WT. With the generally assumed proximity between D1-His190 (and thus D1-Glu189) and Y(Z), the lack of any influence on the electron transfer around Y(Z) straightforwardly implies a strongly hydrophobic environment forcing Glu (acid) and Lys, Arg (basic) at position D1-189 into electro-neutrality. As one alternative, D1-Glu189 could be located at such a large distance from the OEC, Y(Z) and P(+*)(680) that a charge on D1-189X does not influence the electron transfer. This seems less likely in the light of the drastic influence of its direct neighbour, D1-His190, on Y(Z) function. Another alternative is that D1-Glu189 is negatively charged, but is located in a cluster of acid/base groups that compensates for an alteration of charge at position 189, leaving the overall net charge unchanged in the Gln, Lys, and Arg mutants.

Intraoperative fluorescence visualization of the parathyroid gland in rats

Bilateral neck exploration is the standard procedure of primary hyperparathyroidism. Preoperative localization is not mandatory. Intraoperative visualization methods help to avoid unsuccessful explorations and to reduce morbidity rates. In our study, the application of 5-Aminolevulinic acid (5-ALA), a precursor in the heme biosynthesis pathway, led to Protoporphyrin IX (PpIX) accumulation within the parathyroid gland (PTG). PpIX, a metabolite of 5-ALA, causes red fluorescence (635 nm) when stimulated by light of a defined wavelength. Largely invisible under conventional illumination, all PTGs were fluorescence positive and detectable after PpIX targeting and blue light excitation (380-440 nm). Point spectrometry to measure fluorescence intensities, showed a fluorescence ratio between PTG and surrounding thyroid gland tissue of 5.7:1 (p < 0.001). Fluorescence guided PTG biopsies showed no false positive findings in histology. 5-ALA induced PpIX fluorescence to detect PTGs suggests to be a highly sensitive intraoperative visualization method. Hence, the performance of minimally invasive video-assisted parathyroidectomy will be facilitated by this innovative technique.

Medaka eyeless is the key factor linking retinal determination and eye growth

The complete absence of eyes in the medaka fish mutation eyeless is the result of defective optic vesicle evagination. We show that the eyeless mutation is caused by an intronic insertion in the Rx3 homeobox gene resulting in a transcriptional repression of the locus that is rescued by injection of plasmid DNA containing the wild-type locus. Functional analysis reveals that Six3- and Pax6- dependent retina determination does not require Rx3. However, gain- and loss-of-function phenotypes show that Rx3 is indispensable to initiate optic vesicle evagination and to control vesicle proliferation, by that regulating organ size. Thus, Rx3 acts at a key position coupling the determination with subsequent morphogenesis and differentiation of the developing eye.

CD45 tyrosine phosphatase controls common gamma-chain cytokine-mediated STAT and extracellular signal-related kinase phosphorylation in activated human lymphoblasts: inhibition of proliferation without induction of apoptosis

The objective of this study was to test whether CD45 signals can influence signaling processes in activated human lymphoblasts. To this end, we generated lymphoblasts which proliferate in response to common gamma-chain cytokines, but readily undergo apoptosis after cytokine withdrawal. In experiments with the CD45R0 mAb UCHL-1, but not control CD45 mAbs, we found significant inhibition of proliferation. Interestingly, the pan-CD45 mAb GAP8.3, which is most effective in inhibition of OKT-3-mediated proliferation in quiescent lymphocytes, was ineffective in lymphoblasts. Addition of CD3 mAb OKT-3 had no influence on IL-2-mediated proliferation (with or without UCHL-1). In contrast, after addition of OKT-3 to IL-4- and IL-7-stimulated proliferation assays, UCHL-1 signals could not significantly alter cellular proliferation. We did not find induction of apoptosis following CD45R0 signaling. In Western blots using mAbs detecting phosphorylated STAT-3, STAT-5, STAT-6, or extracellular signal-related kinase 1/2, we found that CD45R0 signaling could effectively diminish phosphorylation of these intracellular signaling components. Using RT-PCR, we found that CD45R0 signaling inhibited IL-2 mRNA production without major influence on IL-13, IL-5, or IFN-gamma mRNA levels. Costimulation with OKT-3 and IL-2 optimally induced secretion of IFN-gamma, TNF-alpha, and IL-5, which was not decreased by CD45 signals. In conclusion, we illustrate that CD45R0 signals control early cytokine receptor-associated signaling processes and mRNA and DNA synthesis in activated human lymphoblasts. Furthermore, we show the existence of CD45 epitopes (GAP8.3), which are active and critical for signaling in quiescent lymphocytes, but are nonfunctional in activated human lymphoblasts.

Decreased serum erythropoietin and its relation to anti-erythropoietin antibodies in anaemia of systemic lupus erythematosus

OBJECTIVE

This study was performed to assess erythropoietin levels and anti-erythropoietin antibodies in patients with systemic lupus erythematosus (SLE).

METHODS

The sera of 100 patients with SLE were investigated for serum erythropoietin levels and the presence of anti-erythropoietin antibodies by ELISA. Routine laboratory parameters such as peripheral blood count, relevant parameters of blood chemistry, and immunological parameters of SLE were recorded.

RESULTS

Erythropoietin levels were significantly decreased in SLE patients when related to individual haemoglobin and haematocrit values (P<0.001), suggesting an inadequate erythropoietin response in SLE. Anti-erythropoietin antibodies were found in 46% of SLE patients, and erythropoietin levels (but not haemoglobin or haematocrit values) were significantly decreased in these patients compared with patients without anti-erythropoietin antibodies. Serum erythropoietin concentration as determined by ELISA was reduced in the presence of anti-erythropoietin antibodies. Furthermore, anti-erythropoietin antibodies also correlated with younger age, decreased serum levels of complement factors C3 and C4 and elevated anti-double-stranded DNA antibodies.

CONCLUSIONS

We conclude that the anaemia of SLE is characterized by an inadequate erythropoietin response. Anti-erythropoietin antibodies are frequently present in SLE and interfere with the measurement of serum erythropoietin level. However, these antibodies are not associated with increased severity of SLE-associated anaemia.

Declining chloroquine resistance of Plasmodium falciparum in Lambaréné, Gabon from 1992 to 1998

Plasmodium falciparum malaria continues to threaten human populations in the tropics and travellers in endemic areas. Drug resistance of the parasite is a major problem in treating this devastating disease. In a prospective trial we investigated the in vitro sensitivity of Plasmodium falciparum to chloroquine, quinine and mefloquine in the Albert Schweitzer Hospital in Lambaréné, Gabon every second year from 1992 to 1998. We used the standard WHO in vitro sensitivity assay. Parasite sensitivity to quinine and mefloquine remained stable over the years. However, parasite resistance to chloroquine decreased highly significantly with the change in local malaria treatment policy. In 1992, 100% of parasite isolates showed resistance to chloroquine, whereas in 1998 only 45% were found resistant.

A new approach towards modelling of the carbon degradation cycle at two-stage activated sludge plants

A pilot plant has been operated in order to investigate the performance and operating characteristics of the plant concept developed for the extension of the main Vienna STP. Due to the different operational modes included in the plant concept, modelling of the carbon degradation becomes of crucial importance. A new activated sludge model is introduced which combines parts of the carbon degradation model concepts as they have been released in the ASM1-model and the ASM3-model, respectively. A method is presented which utilises results from mass balance calculations and sludge stabilisation experiments to reduce the uncertainty in the determination of the values of the simulation model parameters.

Comparison of different operational modes of a two-stage activated sludge pilot plant for the extension of the Vienna STP

A pilot plant has been operated over a period of two years in order to investigate the performance and the operating characteristics of the plant concept developed for the extension of the main Vienna STP and to develop a simulation model which will be applied for operation support of the full stage plant. The pilot plant is a two stage activated sludge plant, each stage comprising of four aeration tanks and a clarifier tank. The pilot plant layout allows three different operational modes, each of which has been operated for several periods. The performance of the pilot plant during these periods is described and the different operational modes are compared to each other.

A new process for integrated treatment of industrial wastewater at municipal wastewater treatment plants

A new process for integrated treatment of industrial wastewater at a municipal WWTP is presented. The process uses the ability of heterotrophic bacteria of rapid substrate uptake and storage. The excess sludge from the municipal treatment line is fed to a contact tank, which receives the industrial wastewater via a separate pipeline. The contact tank is aerated to such a degree that secures complete substrate uptake but minimises oxygen consumption due to instant substrate degradation. The sludge from the contact tank is mechanically pre-thickened and then fed to an anaerobic digester. Hence, the major portion of the incoming COD load of the industrial wastewater is transferred to the anaerobic digester, where it contributes to an increased biogas production. The back load of the industrial wastewater treatment process to the municipal treatment line is very low.