Recycling Fe and improving organic pollutant removal via in situ forming magnetic core-shell Fe3O4@CaFe-LDH in Fe(II)-catalyzed oxidative wastewater treatment

Due to its high efficiency, Fe(II)-based catalytic oxidation has been one of the most popular types of technology for treating growing organic pollutants. A lot of chemical Fe sludge along with various refractory pollutants was concomitantly produced, which may cause secondary environmental problems without proper disposal. We here innovatively proposed an effective method of achieving zero Fe sludge, reusing Fe resources (Fe recovery = 100%) and advancing organics removal (final TOC removal > 70%) simultaneously, based on the in situ formation of magnetic Ca-Fe layered double hydroxide (Fe3O4@CaFe-LDH) nano-material. Cations (Ca2+ and Fe3+) concentration (≥ 30 mmol/L) and their molar ratio (Ca:Fe ≥ 1.75) were crucial to the success of the method. Extrinsic nano Fe3O4 was designed to be involved in the Fe(II)-catalytic wastewater treatment process, and was modified by oxidation intermediates/products (especially those with COO- structure), which promoted the co-precipitation of Ca2+ (originated from Ca(OH)2 added after oxidation process) and by-produced Fe3+ cations on its surface to in situ generate core-shell Fe3O4@CaFe-LDH. The oxidation products were further removed during Fe3O4@CaFe-LDH material formation via intercalation and adsorption. This method was applicable to many kinds of organic wastewater, such as bisphenol A, methyl orange, humics, and biogas slurry. The prepared magnetic and hierarchical CaFe-LDH nanocomposite material showed comparable application performance to the recently reported CaFe-LDHs. This work provides a new strategy for efficiently enhancing the efficiency and economy of Fe(II)-catalyzed oxidative wastewater treatment by producing high value-added LDHs materials.

Soil colloids can significantly enhance spreading of polybromodiphenyl ethers in groundwater by serving as an effective carrier

Polybromodiphenyl ethers (PBDEs), the widely used flame retardants, are common contaminants in surface soils at e-waste recycling sites. The association of PBDEs with soil colloids has been observed, indicating the potential risk to groundwater due to colloid-facilitated transport. However, the extent to which soil colloids may enhance the spreading of PBDEs in groundwater is largely unknown. Herein, we report the co-transport of decabromodiphenyl ester (BDE-209) and soil colloids in saturated porous media. The colloids released from a soil sample collected at an e-waste recycling site in Tianjin, China, contain high concentration of PBDEs, with BDE-209 being the most abundant conger (320 ± 30 mg/kg). The colloids exhibit relatively high mobility in saturated sand columns, under conditions commonly observed in groundwater environments. Notably, under all the tested conditions (i.e., varying flow velocity, pH, ionic species and ionic strength), the mass of eluted BDE-209 correlates linearly with that of eluted soil colloids, even though the mobility of the colloids varies markedly depending on the specific hydrodynamic and solution chemistry conditions involved. Additionally, the mass of BDE-209 retained in the columns also correlates strongly with the mass of retained colloids. Apparently, the PBDEs remain bound to soil colloids during transport in porous media. Findings in this study indicate that soil colloids may significantly promote the transport of PBDEs in groundwater by serving as an effective carrier. This might be the reason why the highly insoluble and adsorptive PBDEs are found in groundwater at some PBDE-contaminated sites.

Enhancing the bioavailability and activity of natural antioxidants with nanobubbles and nanoparticles

KEY POLICY HIGHLIGHTSNanobubbles and nanoparticles may enhance the polyphenols' bioavailabilityNanobubbles may stimulate the activation of Nrf2 and detox enzymesArmoured oxygen nanobubbles may enhance radiotherapy or chemotherapy effects.

Inhibitory effects of Curcumae Radix carbonisata-based carbon dots against liver fibrosis induced by carbon tetrachloride in mice

As a processed product of traditional Chinese medicine Curcumae Radix, Curcumae Radix Carbonisata (CRC) has been widely used in the treatment of liver diseases in ancient medical books. In this study, novel carbon dots (CDs) extending from 1.0 to 4.5 nm were separated from fluid extricates of CRC. Meanwhile, a liver fibrosis model induced by carbon tetrachloride (CCl4) was utilized to determine the inhibitory effects of CRC-CDs against liver fibrosis. The results exhibited the CRC-CDs with a quantum yield of 1.34% have a significant inhibitory effect on CCl4-induced liver fibrosis, as demonstrated by improving hepatocyte degeneration and necrosis, inflammatory cell infiltration and fibrotic tissue hyperplasia, downregulating the levels of alanine transaminase (ALT), aspartate aminotransferase (AST), total bilirubin (TBIL), direct bilirubin (DBIL), total bile acid (TBA), triglyceride (TG), tumour necrosis factor-α (TNF-α), interleukin (IL)-6 and IL-1β in the serum, upregulating the contents of superoxide dismutase (SOD), reduced glutathione (GSH), and downregulating the concentration of malondialdehyde (MDA), which lays an important foundation for the development of CRC-CDs as a novel drug for the treatment of liver fibrosis, and provide a certain experimental basis for the clinical application of CRC-CDs in the future.

Techniques for assessing telomere length: A methodological review

Telomeres are located at the ends of chromosomes and have specific sequences with a distinctive structure that safeguards genes. They possess capping structures that protect chromosome ends from fusion events and ensure chromosome stability. Telomeres shorten in length during each cycle of cell division. When this length reaches a certain threshold, it can lead to genomic instability, thus being implicated in various diseases, including cancer and neurodegenerative disorders. The possibility of telomeres serving as a biomarker for aging and age-related disease is being explored, and their significance is still under study. This is because post-mitotic cells, which are mature cells that do not undergo mitosis, do not experience telomere shortening due to age. Instead, other causes, for example, exposure to oxidative stress, can directly damage the telomeres, causing genomic instability. Nonetheless, a general agreement has been established that measuring telomere length offers valuable insights and forms a crucial foundation for analyzing gene expression and epigenetic data. Numerous approaches have been developed to accurately measure telomere lengths. In this review, we summarize various methods and their advantages and limitations for assessing telomere length.

From lab to industrial development of lipid nanocarriers using quality by design approach

Lipid nanocarriers have attracted a great deal of interest in the delivery of therapeutic molecules. Despite their many advantages, compliance with quality standards and reproducibility requirements still constrain their industrial production. The relatively high failure rate in lipid nanocarrier research and development can be attributed to immature bottom-up manufacturing practices, leading to suboptimal control of quality attributes. Recently, the pharmaceutical industry has moved toward quality-driven manufacturing, emphasizing the integration of product and process development through the principles of quality by design. Quality by design in the pharmaceutical industry involves a thorough understanding of the quality profile of the target product and involves an assessment of potential risks during the design and development phases of pharmaceutical dosage forms. By identifying essential quality characteristics, such as the active ingredients, excipients and manufacturing processes used during research and development, it becomes possible to effectively control these aspects throughout the life cycle of the drug. Successful commercialization of lipid nanocarriers can be achieved if large-scale challenges are addressed using the QbD approach. QbD has become an essential tool because of its advantages in improving processes and product quality. The application of the QbD approach to the development of lipid nanocarriers can provide comprehensive and remarkable knowledge enabling the manufacture of high-quality products with a high degree of regulatory flexibility. This article reviews the basic considerations of QbD and its application in the laboratory and large-scale development of lipid nanocarriers. Furthermore, it provides forward-looking guidance for the industrial production of lipid nanocarriers using the QbD approach.

A novel mathematical template for developing fDOM probe fluorescence signal correction models for freshwaters

The reliable application of field deployable fluorescent dissolved organic matter (fDOM) probes is hindered by several influencing factors which need to be compensated. This manuscript describes the corrections of temperature, pH, turbidity and inner filter effect on fluorescence signal of a commercial fDOM probe (fDOMs). For this, Australian waters with wide ranging qualities were selected, e.g. dissolved organic carbon (DOC) ranging from ∼1 to ∼30 mg/L, specific UV absorbance at 254 nm from ∼1 to ∼6 L/m/mg and turbidity from ∼1 to ∼ 350 FNU. Laboratory-based model calibration experiments (MCEs) were performed. A model template was developed and used for the development of the correction models. For each factor, data generated through MCEs were used to determine model coefficient (α) values by fitting the generated model to the experimental data. Four discrete factor models were generated by determination of a factor-specific α value. The α values derived for each water of the MCEs subset were consistent for each factor model. This indicated generic nature of the four α values across wide-ranging water qualities. High correlation between fDOMs and DOC were achieved after applying the four-factor compensation models to new data (r, 0.96, p < 0.05). Also, average biases (and %) between DOC predicted through fDOMs and actual DOC were decreased by applying the four-factor compensation model (from 3.54 (60.9%) to 1.28 (16.7%) mg/L DOC). These correction models were incorporated into a Microsoft EXCEL-based software termed EXOf-Correct for ready-to-use applications.

Chitosan-based matrix as a carrier for bacteriophages

Wound healing is a dynamic and complex process where infection prevention is essential. Chitosan, thanks to its bactericidal activity against gram-positive and gram-negative bacteria, as well as anti-inflammatory and hemostatic properties, is an excellent candidate to design dressings for difficult-to-heal wound treatment. The great advantage of this biopolymer is its capacity to be chemically modified, which allows for the production of various functional forms, depending on the needs and subsequent use. Moreover, chitosan can be an excellent polymer matrix for bacteriophage (phage) packing as a novel alternative/supportive antibacterial therapy approach. This study is focused on the preparation and characteristics of chitosan-based material in the form of a film with the addition of Pseudomonas lytic phages (KTN4, KT28, and LUZ19), which would exhibit antibacterial activity as a potential dressing that accelerates the wound healing. We investigated the method of producing a polymer based on microcrystalline chitosan (MKCh) to serve as the matrix for phage deposition. We described some important parameters such as average molar mass, swelling capacity, surface morphology, phage release profile, and antibacterial activity tested in the Pseudomonas aeruginosa bacterial model. The chitosan polysaccharide turned out to interact with phage particles immobilizing them within a material matrix. Nevertheless, with the high hydrophilicity and swelling features of the prepared material, the external solution of bacterial culture was absorbed and phages went in direct contact with bacteria causing their lysis in the polymer matrix. KEY POINTS: • A novel chitosan-based matrix with the addition of active phages was prepared • Phage interactions with the chitosan matrix were determined as electrostatic • Phages in the matrix work through direct contact with the bacterial cells.

Spectral-fluorescent study of substituted trimethine cyanine dyes in solutions and in complexes with DNA. Effects of aggregation, moderate heating, and decreasing pH

Trimethine cyanine dyes are widely used as probes for the detection, study and quantification of biomolecules. In particular, cationic trimethine cyanines noncovalently interact with DNA with growing fluorescence. However, their use is often limited by the tendency to self-association - to the formation of aggregates. Disubstituted trimethine cyanines with hydrophobic substituents are especially prone to aggregation. In this work, we studied the interaction of a number of substituted trimethine cyanines with DNA (in aqueous buffer solutions) and showed that their aggregation strongly interfered with their use as fluorescent probes for DNA. To eliminate this drawback, preliminary heating of dye solutions with DNA to 60-70 °C was used, followed by cooling to room temperature. Compared to the experiments without heating, an increase in the dye fluorescence intensity was observed due to the partial thermal decomposition of the aggregates and the interaction of the resulting monomers with DNA. To decompose aggregates, another method was also used - protonation of the dyes with amino substituents in buffer solutions with pH 5.0, which also led to growing the dye fluorescence intensity in the presence of DNA. Complexes of the dyes with DNA were modeled using molecular docking. Effective binding constants of the dyes to DNA and detection limits when using the dyes as probes for DNA (LOD and LOQ) were determined. It is shown that dye 3 with heating in neutral buffer and dye 1 in acidic buffer may be recommended as sensitive probes for DNA. It is concluded that the method of preliminary heating may be applied to dyes prone to aggregation, for improving their properties as biomolecular probes. Another possible means to reduce the interfering effects of dye aggregates is to use easily protonated dyes (with amino substituents) in slightly acidic media.

Spectroscopic investigation, dielectric and antimicrobial properties of chitin-cellulose@ZnO/CuO conductive nanocomposites

In this research, we fabricated a functional conductive nanocomposite with valuable properties through a chitin (CH) and cellulose (CE) polymerization process, incorporating ZnO/(0.1, 0.2, 0.3 mol.%) CuO bioactive nanoparticles. These bioactive nanoparticles, synthesized through sol-gel and polymerization interactions, greatly enhanced the structural, dielectric, and antimicrobial characteristics of CH-CE@ZnO/CuO conductive nanocomposites. The morphological analysis revealed that these nanoparticles, with diameters ranging from 11-25 nm, formed covalent bonds with the membrane matrix, bolstering the conductive nanocomposites ' structural integrity and dielectric performance. The dielectric properties of the conductive nanocomposites were significantly enhanced by the even distribution of ZnO/CuO nanoparticles within the CH-CE composite. Additionally, antimicrobial assessments demonstrated that the CH-CE@ZnO/CuO conductive nanocomposites displayed significant antibacterial properties against the Escherichia coli and Staphylococcus aureus, showcasing their potential as active packaging materials for electronic, biosensors, and sustainable applications.

Tailoring the covalent organic frameworks based polymer materials for solar-driven atmospheric water harvesting

Atmospheric water harvesting through reticular materials is an innovation that has the potential to change the world. Here, this study offers a technique for creating a solar-powered hygroscopic polymer material for atmospheric water harvesting with the reticular materials. The results show that the porous hygroscopic polymer materials can achieve high performance with high vapor capture (up to ac. 28.8-49.7 mg/g at 28-38 %RH and 25  ℃), rapid photothermal conversion efficiency (up to 32.2 ℃ within 15 min under 1000 W/m-2 light at 25 ℃), a low desorption temperature (lower than 40 ℃), and an effective water release rate. Besides, the material also has excellent water-retention properties, which can effectively store desorbed liquid water in polymer networks for use by vegetation during water demand periods. The strategy opens new avenues for atmospheric water-harvesting materials, which will hopefully solve the global crisis of freshwater shortages.

In-situ measurement of the internal compaction of a soft material caused by permeation flow

HYPOTHESIS

The compaction of hydrogel films under permeation flow can be measured, in-situ, by tracking the internal displacements of their structure, thereby revealing the internal deformation profile. Additionally, monitoring the permeation flow rate and applied pressure over time enables determination of variations in the hydrogel's permeability due to flow-induced compaction. Hydrogels are soft porous materials capable of containing high amounts of water within their polymeric matrix. Flow-induced internal deformation can modify the hydrogel's permeability and selectivity, which are important attributes in separation processes, both industrial (e.g., membrane-based water purification) and natural (mucous filters in suspension feeders and intestinal lining) systems. Measuring the flow-induced compaction in thin hydrogels films can reveal the interplay between flow and permeability. However, the micro-scale internal compaction remains uncharted for due to experimental challenges.

EXPERIMENTS

A technique is demonstrated for analyzing the compaction and stratification of permeable soft materials, in-situ, created by a pressure-driven permeation flow. To this end, the internal deformations within a soft material layer are calculated, based on tracking the positions of fluorescent micro-tracers that are embedded within the soft material. We showcase the capabilities of this technique by examining a hundred-micron-thick calcium-alginate cake deposited on a nanofiltration membrane, emphasizing the achieved micro-scale resolution of the local compaction measurements.

FINDINGS

The results highlight the possibility to examine thin hydrogel films and their internal deformation produced by flow-induced stresses when varying the flow conditions. The method enables the simultaneous calculation of the soft material's permeance, as the pressure-driven flow conditions are continuously monitored. In summary, the proposed method provides a powerful tool for characterizing the behaviour of permeable soft materials under permeation conditions, with potential applications in engineering, biophysics and material science.

Rational designing NiVO3@CoNi-MOF heterostructures on activated carbon cloth for high-performance asymmetric supercapacitors and oxygen evolution reaction

Binder-free self-supported carbon cloth electrode provides novel strategies for the preparation of MOFs, effectively improving the conductivity and promoting charge transfer. Combining MOFs with vanadate to form a unique heterogeneous structure provides a large specific surface area and more active sites, further enhancing the kinetics of MOFs. Herein, a self-supported carbon cloth electrode is prepared by in-situ growth of CoNi-MOFs on activated carbon cloth (AC) and coating with NiVO3. The heterostructure increases the specific surface area and exposes more active sites to promote the adsorption and diffusion of ions, thus enhancing the kinetic activity and optimizing charge storage behavior. As expected, the NiVO3@CoNi-MOF/AC exhibits a specific capacitance of up to 19.20 F/cm2 at 1 mA/cm2. The asymmetric supercapacitors (ASCs) assembled by NiVO3@CoNi-MOF/AC and annealed activated carbon cloth achieve an energy density of 1.27 mWh/cm2 at a power density of 4 mW/cm2 and have a capacitance retention of 96.43 % after 10,000 cycles. In addition, the NiVO3@CoNi-MOF/AC as electrocatalyst has an overpotential of 370 mV at 10 mA/cm2 and a Tafel slope of 208 mV dec-1, demonstrating remarkable electrocatalytic oxygen evolution reaction performance. These unique heterostructures endow the electrode with more electrochemical selectivity and provide new key insights for designing multifunctional materials.

Unveiling the influence of hydrophobicity on inhibiting hydrogen dissociation for enhanced photocatalytic hydrogen evolution of covalent organic frameworks

Covalent organic frameworks (COFs) have gained considerable interest as candidate photocatalysts for hydrogen evolution. In this work, we synthesized β-keto-enamine-based COFs (TpPa-X, TpDB, and TpDTP) to explore the relations between structures and photocatalytic hydrogen evolution. COFs were divided into two groups: (1) TpPa-X with different substituents attached to the TpPa backbone and (2) COFs featuring diamine linkers of varied lengths (TpDB and TpDTP). Experiments and density functional theory (DFT) calculations show that moderate hydrophobicity is favorable for the photocatalytic hydrogen evolution process, and acceptable contact angles are anticipated to range from 65° to 80°. Naturally, there are comprehensive factors that affect photocatalytic reactions, and the regulation of different backbones and substituents can considerably affect the performance of COFs for photocatalytic hydrogen evolution in terms of electronic structure, specific surface area, surface wettability, carrier separation efficiency, and hydrogen dissociation energy. Results show that TpPa-Cl2 (TpPa-X, X  = Cl2) demonstrates the highest photocatalytic activity, approximately 14.51 mmol g-1h-1, with an apparent quantum efficiency of 4.62 % at 420 nm. This work provides guidance for designing efficient COF-based photocatalysts.

Suppression of coffee rings by controllable nanoparticle enrichment through superhydrophobicity-enabled dynamic evaporation

Coffee rings formed by evaporation of analyte-containing droplets are widely observed in micropatterning, bio-arrays, and trace detection. The coffee-ring effect caused by contact line pinning significantly affects the detection uniformity and sensitivity. Here, we propose a simple and operable method to effectively suppress coffee rings through controllable nanoparticles aggregation by superhydrophobicity-enabled dynamic evaporation. The gold nanoparticles (AuNPs) deposition footprint formed after dynamic evaporation on an integrated superhydrophobic surface was reduced by ∼3 orders of magnitude compared to that of non-interventional evaporation. Detailed experiments, numerical simulations, and theoretical studies have revealed that substrate wettability, temperature and droplet motion behaviors play significant roles in suppressing coffee-ring effect. More critically, based on the force mechanism of AuNPs at the interface/contact line, universal mathematical models and regime maps were established to classify the different deposition modes for AuNPs under different evaporation conditions by introducing dimensionless parameter G, revealing the enrichment mechanism of AuNPs in droplets under superhydrophobicity-enabled dynamic evaporation. The accuracy of the theoretical model and enrichment mechanism was demonstrated through the single-molecule detection of rhodamine 6G with excellent sensitivity (10-17 M, enhancement factor ∼1013) and perfect uniformity (relative standard deviation ∼5.57 %), which provides a valuable guide for research and applications of nanoparticle aggregation.

Fabrication of cinnamon essential oil nanoemulsions with high antibacterial activities via microfluidization

The high volatility and hydrophobicity of cinnamon essential oils (CiEO) limited their practical application. To enhance their stability and antibacterial activity, nanoemulsions encapsulating CiEO were prepared using hydroxypropyl-β-cyclodextrin/lauroyl arginate (HPCD/LAE) inclusion complexes through high-pressure microfluidization (HPM). Effects of HPM parameters on the stability and antibacterial properties of nanoemulsion were investigated. Results revealed that increased processing pressure and cycle numbers were associated with reduced droplet size and greater homogeneity in CiEO distribution. Storage and thermal stability were optimized at 100 MPa and seven cycles. Moreover, the nanoemulsions showed strong synergistic antibacterial against E. coli (19.79 mm) and S. aureus (23.61 mm) compared with LAE (11.52 mm and 12.82 mm, respectively) and CiEO alone (13.26 mm and 17.68 mm, respectively). This study provided new information for constructing CiEO nanoemulsion, which is suitable for use in the food industry.

Preparation of umami peptides from chicken breast by batch coupled enzymatic hydrolysis and membrane separation mode and the taste mechanism of identified umami peptides

Batch coupled enzymatic hydrolysis and membrane separation mode (BCEH-MSM) is efficient in preparing active peptides due to enzyme being more purposeful in hydrolysing macromolecular. Therefore, BCEH-MSM probably could be an alternative option to the traditional enzymatic hydrolysis and offline membrane separation mode (TEH-OMSM). This work aimed to explore the potential of BCEH-MSM in enhancing the enzymatic hydrolysis (EH) efficiency and the umami of the enzymatic hydrolysate. The EH efficiency was valuated based on product yields. Amino acid analyzer and HPLC were used to analyze tasting compounds. Electronic-tongue was used to determine umami intensity. The results showed that BCEH-MSM exhibited superior EH efficiency and higher umami intensity compared to TEH-OMSM. LC-MS/MS was used to identify peptides with higher umami intensity in the enzymatic hydrolysate. LGEETF, VNFDGEI, and QLSELLRAGSSPNL had umami profile verified by electronic-tongue. Molecular docking further showed that crucial amino acid residues involved in the binding to T1R1/T1R3 was His145.

Effects of molecular weight of hydrolysate on the formation of soy protein isolate hydrolysate nanofibrils: Kinetics, structures, and interactions

Enzymatic hydrolysis prior to protein fibrillation was an effective way to facilitate the formation of nanofibrils. This study aimed to investigate the effects of molecular weights of hydrolysate on the kinetics, structures, and interactions of soy protein isolate (SPI) hydrolysate nanofibrils. The results showed that hydrolysate with molecular weight > 10 kDa showed a distinct fibrillation kinetics curve and a higher apparent rate constant (27.72) during fibrillation, indicating their vital role in determining the fibrillation. Hydrolysate with molecular weight > 10 kDa could form nanofibrils with higher radius gyration (17.11 ± 0.77 Å) due to stronger hydrophobic interaction, showing a stronger fibrillation ability. Hydrolysate with molecular weight within 5-10 kDa exhibited enhanced π-π stacking interactions during fibrillation, thereby promoting the extension of nanofibrils, and contributing to the formation of more nanofibrils. Hydrolysate with molecular weight < 5 kDa tended to randomly aggregate during fibrillation, resulting in a significant loss of cross-β structures in nanofibrils. Therefore, hydrolysate with different molecular weights exhibited synergistic effects during fibrillation.

Co-encapsulation of curcumin and fucoxanthin in solid-in-oil-in-water multilayer emulsions: Characterization, stability and programmed sequential release

To enhance the bioavailability of bioactives with varying efficacy in the gastrointestinal tract (GIT), a co-delivery system of solid-in-oil-in-water (S/O/W) emulsion was designed for the co-encapsulation of two bioactives in this paper. S/O/W emulsions were fabricated utilizing fucoxanthin (FUC)-loaded nanoparticles (NPs) as the solid phase, coconut oil containing curcumin (Cur) as the oil phase, and carboxymethyl starch (CMS)/propylene glycol alginate (PGA) complex as the aqueous phase. The high entrapment efficiency of Cur (82.3-91.3%) and FUC (96.0-96.1%) was found in the CMS/PGA complex-stabilized S/O/W emulsions. Encapsulation of Cur and FUC within S/O/W emulsions enhanced their UV and thermal stabilities. In addition, S/O/W emulsions prepared with CMS/PGA complexes displayed good stability. More importantly, the formed S/O/W emulsion possessed programmed sequential release characteristics, delivering Cur and FUC to the small intestine and colon, respectively. These results contributed to designing co-delivery systems for the programmed sequential release of two hydrophobic nutrients in the GIT.

Effect of cross-linking density on the rheological behavior of ultra-soft chitosan microgels at the oil-water interface

In this paper, microgels with uniform particle size were prepared by physically cross-linking the hydrophobically modified chitosan (h-CS) with sodium phytate (SP). The effects of cross-linking density on the interfacial adsorption kinetics, viscoelasticity, stress relaxation, and micorheological properties of the hydrophobically modified chitosan microgels (h-CSMs) at the oil-water interface were extensively investigated by the dilatational rheology, compressional rheology, and particle tracing microrheology. The results were correlated with the particle size, morphology, and elasticity of the microgels characterized by dynamic light scattering and atomic force microscopy. It was found that with the increase of cross-linking density, the h-CSMs changed from a polymer-like state to ultra-soft fussy spheres with higher elastic modulus. The compression isotherms demonstrated multi-stage increase caused by the interaction between the shells and that between the cores of the microgels successively. As the increase of cross-linking density, the h-CSMs diffused slower to the oil-water interface, but demonstrating faster permeation adsorption and rearrangement at the oil-water interface, finally forming interfacial layers of higher viscoelastic modulus due to the core-core interaction. Both the initial tension relaxation and the microgel rearrangement after interface expansion became faster as the microgel elasticity increased. The interfacial microrheology demonstrated dynamic caging effect caused by neighboring microgels. This article provides a more comprehensive understanding of the behaviors of polysaccharide microgels at the oil-water interface.

Cryo-electron tomography study of the evolution of wormlike micelles to saturated networks and perforated vesicles

HYPOTHESIS

The formation of micellar aggregates and the changes in their morphology are crucial for numerous practical applications of surfactants. However, a proper structural characterization of complicated micellar nanostructures remains a challenge. This paper demonstrates the advances of cryo-electron tomography (cryo-ET) in revealing the structural characteristics that accompany the evolution of surfactant aggregates.

EXPERIMENTS

By using cryo-ET in combination with cryo-transmission electron microscopy (cryo-TEM), small-angle neutron scattering (SANS), and rheometry, studies were carried out on a model system composed of zwitterionic and nonionic surfactants. In this system, the molecular packing parameter was increased gradually by increasing the molar fraction of nonionic surfactant.

FINDINGS

A series of structural transformations was observed: linear wormlike micelles (WLMs) → branched WLMs → saturated network of multiconnected WLMs → perforated vesicles (stomatosomes). The transformations occur through an increase in the number of branches at the expense of cylindrical subchains and semispherical endcaps. Exponential distribution of subchains length was confirmed experimentally for multiconnected saturated networks. The stomatosomes were formed when the length of subchains becomes much shorter than the persistence length, causing the three-dimensional (3D) structure to transform into a two-dimensional (2D) membrane. This work identifies the mechanism of the structural changes, which can be further used to design various surfactant self-assemblies.

Identification of hypermucoviscous Klebsiella pneumoniae K1, K2, K54 and K57 capsular serotypes by Raman spectroscopy

Antimicrobial resistance poses a significant challenge in modern medicine, affecting public health. Klebsiella pneumoniae infections compound this issue due to their broad range of infections and the emergence of multiple antibiotic resistance mechanisms. Efficient detection of its capsular serotypes is crucial for immediate patient treatment, epidemiological tracking and outbreak containment. Current methods have limitations that can delay interventions and increase the risk of morbidity and mortality. Raman spectroscopy is a promising alternative to identify capsular serotypes in hypermucoviscous K. pneumoniae isolates. It provides rapid and in situ measurements with minimal sample preparation. Moreover, its combination with machine learning tools demonstrates high accuracy and reproducibility. This study analyzed the viability of combining Raman spectroscopy with one-dimensional convolutional neural networks (1-D CNN) to classify four capsular serotypes of hypermucoviscous K. pneumoniae: K1, K2, K54 and K57. Our approach involved identifying the most relevant Raman features for classification to prevent overfitting in the training models. Simplifying the dataset to essential information maintains accuracy and reduces computational costs and training time. Capsular serotypes were classified with 96 % accuracy using less than 30 Raman features out of 2400 contained in each spectrum. To validate our methodology, we expanded the dataset to include both hypermucoviscous and non-mucoid isolates and distinguished between them. This resulted in an accuracy rate of 94 %. The results obtained have significant potential for practical healthcare applications, especially for enabling the prompt prescription of the appropriate antibiotic treatment against infections.

Modulating protein unfolding and refolding via the synergistic association of an anionic and a nonionic surfactant

HYPOTHESIS

Nonionic surfactants can counter the deleterious effect that anionic surfactants have on proteins, where the folded states are retrieved from a previously unfolded state. However, further studies are required to refine our understanding of the underlying mechanism of the refolding process. While interactions between nonionic surfactants and tightly folded proteins are not anticipated, we hypothesized that intermediate stages of surfactant-induced unfolding could define new interaction mechanisms by which nonionic surfactants can further alter protein conformation.

EXPERIMENTS

In this work, the behavior of three model proteins (human growth hormone, bovine serum albumin, and β-lactoglobulin) was investigated in the presence of the anionic surfactant sodium dodecylsulfate, the nonionic surfactant β-dodecylmaltoside, and mixtures of both surfactants. The transitions occurring to the proteins were determined using intrinsic fluorescence spectroscopy and far-UV circular dichroism. Based on these results, we developed a detailed interaction model for human growth hormone. Using nuclear magnetic resonance and contrast-variation small-angle neutron scattering, we studied the amino acid environment and the conformational state of the protein.

FINDINGS

The results demonstrate the key role of surfactant cooperation in defining the conformational state of the proteins, which can shift away or toward the folded state depending on the nonionic-to-ionic surfactant ratio. Dodecylmaltoside, initially a non-interacting surfactant, can unexpectedly associate with sodium dodecylsulfate-unfolded proteins to further impact their conformation at low nonionic-to-ionic surfactant ratio. When this ratio increases, the protein begins to retrieve the folded state. However, the native conformation cannot be fully recovered due to remnant surfactant molecules still adsorbed to the protein. This study demonstrates that the conformational landscape of the protein depends on a delicate interplay between the surfactants, ultimately controlled by the ratio between them, resulting in unpredictable changes in the protein conformation.

A novel red fluorescent and dynamic nanocomposite hydrogel based on chitosan and alginate doped with inclusion complex of carbon dots

Red fluorescent hydrogels possessing injectable and self-healing properties have widespread potential in biomedical field. It is still a challenge to achieve a biomacromolecules based dynamic hydrogels simultaneously combining with excellent red fluorescence, good mechanical properties, and biocompatibility. Here we first explore hydrophilic inclusion complex of (R-CDs@α-CD) derived from hydrophobic red fluorescent carbon dots (R-CDs) and α-cyclodextrin (α-CD), and then achieved a red fluorescent and dynamic polysaccharide R-CDs@α-CD/CEC-l-OSA hydrogel. The nanocomposite hydrogel can be fabricated through controlled doping of red fluorescent R-CDs@α-CD into dynamic polymer networks, taking reversibly crosslinked N-carboxyethyl chitosan (CEC) and oxidized sodium alginate (OSA) as an example. The versatile red fluorescent hydrogel simultaneously combines the features of injection, biocompatibility, and augmented mechanical properties and self-healing behavior, especially in rapid self-recovery even after integration. The R-CDs@α-CD uniformly dispersed into dynamic hydrogel played the role of killing two birds with one stone, that is, endowing red emission of a hydrophilic fluorescent substance, and improving mechanical and self-healing properties as a dynamic nano-crosslinker, via forming hydrogen bonds as reversible crosslinkings. The novel red fluorescent and dynamic hydrogel based on polysaccharides is promising for using as biomaterials in biomedical field.

Redox-switchable microemulsions with efficient phase separation and surfactant recycling

HYPOTHESIS

Switchable microemulsions (MEs) are those capable of adaptively responding to the action of internal or external stimuli. For redox-switchable MEs to obtain high-efficiency phase separation and surfactant recycling, it may be one of the keys to adequately turn off the interfacial activity of surfactants and reduce the solubility of the closed surfactants in the oil phase.

EXPERIMENTS

Monophasic MEs consisting 11-butylselanyl-undecyl sulfate sodium (C4SeC11SO4Na), n-butanol, n-octane, and water were fabricated using the pseudo-ternary phase diagram method. Their structural features and droplets size were characterized by conductivity, dynamic light scattering (DLS) and cryogenic transmission electron microscopy (cryo-TEM), respectively. The redox response of MEs was studied using a combination of visual observations and DLS, cryo-TEM, nuclear magnetic resonance (NMR) and thin-layer tomography. The efficient recycling of C4SeC11SO4Na from a well-emulsified eluent is conceptually demonstrated.

FINDINGS

The reversible transition between C4SeC11SO4Na and C4SeOC11SO4Na is achieved under the alternating action of H2O2 and N2H4, by which C4SeC11SO4Na-based monophasic MEs are able to efficiently demulsify and regenerate, respectively, regardless of their type. After H2O2-induced demulsification of the MEs, C4SeOC11SO4Na can be efficiently recycled with the water phase. We hope that such a redox-switching method may benefit some technological applications. For example, it offers exciting possibilities for simultaneous recycling C4SeC11SO4Na and removal of oil from a well-emulsified eluent. Around 97.1 ± 0.3 % of C4SeC11SO4Na could be recycled over five cycles with no apparent loss. After a simple and conventional treatment with anion-exchange resin and active carbon, the total organic carbon and chemical oxygen demand of the waste water were 17.4 ± 2.8 and 26.2 ± 1.4 mg/L, respectively.

Modulating the conformation of microgels by complexation with inorganic nanoparticles

HYPOTHESIS

The complexation of microgels with rigid nanoparticles is an effective way to impart novel properties and functions to the resulting hybrid particles for applications such as in optics, catalysis, or for the stabilization of foams/emulsions. The nanoparticles affect the conformation of the polymer network, both in bulk aqueous environments and when the microgels are adsorbed at a fluid interface, in a non-trivial manner by modulating the microgel size, stiffness and apparent contact angle.

EXPERIMENTS

Here, we provide a detailed investigation, using light scattering, in-situ atomic force microscopy and nano-indentation experiments, of the interaction between poly(N-isopropylacrylamide) microgels and hydrophobized silica nanoparticles after mixing in aqueous suspension to shed light on the network reorganization upon nanoparticle incorporation.

FINDINGS

The addition of nanoparticles decreases the microgels' bulk swelling and thermal response. When adsorbed at an oil-water interface, a higher ratio of nanoparticles influences the microgel's stiffness as well as their hydrophobic/hydrophilic character by increasing their effective contact angle, consequently modulating the monolayer response upon interfacial compression. Overall, these results provide fundamental understanding on the complex conformation of hybrid microgels in different environments and give inspiration to design new materials where the combination of a soft polymer network and nanoparticles might result in additional functionalities.

Full life cycle green preparation of collagen-based food packaging films using Halocynthia roretzi as raw material

The extraction of collagen for packaging films typically requires a time-consuming process and the use of substantial chemicals. Herein, we present a full life cycle green preparation method for rapidly producing collagen-based food packaging films using Halocynthia roretzi (HR), a collagen-rich marine organism, as raw material. We first prepared the micro/nano-sized collagen fibers from HR tissue by utilizing urea and sonication as effective hydrogen-bond breakers. Subsequently, the collagen fiber was rapidly fabricated into a film through vacuum filtration. The resulting collagen fiber film (CFF) exhibited a uniform and dense surface, along with good tensile properties, water resistance, and biodegradability. In addition, the deposition of chitosan (CS) on the surface of CFF resulted in a remarkable preservation effect for both strawberries and pork. This full life cycle preparation method for collagen-based films provides a promising and innovative approach to the sustainable preparation of food packaging films.

High internal phase Pickering emulsions stabilized by egg yolk-carboxymethyl cellulose as an age-friendly dysphagia food: Tracking the dynamic transition from co-solubility to coacervates

Although protein-polysaccharide complexes with different phase behaviors all show potential for stabilizing high internal phase Pickering emulsions (HIPPEs), it is not clarified which aggregation state is more stable and age-friendly. In this study, we investigated and compared the stability and age friendliness of HIPPEs stabilized with egg yolk and carboxymethyl cellulose (EYCMC) in different phase behaviors. The results revealed differences in particle size, aggregation state, charge potential, and stability of secondary and tertiary structures of EYCMC. The behavior of EYCMC at the oil-water interface was mainly divided into three phases: rapid diffusion, permeation, and reorganization. The electrostatic interaction, kinetic hindrance, and depletion attraction were the mechanisms primarily involved in stabilizing HIPPEs by EYCMC. Rheological analysis results indicated that HIPPEs had excellent viscoelasticity, structural recovery properties and yield stress. HIPPEs were used in 3D printing, electronic nose testing, IDDSI testing and in vitro digestive simulations for the elderly, demonstrating a fine appearance, safe consumption and bioaccessibility of β-carotene. Soluble complexes showed the best stability and age friendliness compared to other aggregated forms. This study serves as a foundational source of information for developing innovative foods utilizing HIPPEs.

12-hydroxystearic acid-mediated in-situ surfactant generation: A novel approach for organohydrogel emulsions

HYPOTHESIS

Organohydrogel emulsions display unique rheological properties and contain hydrophilic and lipophilic domains highly desirable for the loading of active compounds. They find utility in various applications from food to pharmaceuticals and cosmetic products. The current systems have limited applications due to complex expensive formulation and/or processing difficulties in scale-up. To solve these issues, a simple emulsification process coupled with unique compounds are required.

EXPERIMENTS

Here, we report an organohydrogel emulsion based only on a low concentration of 12-hydroxystearic acid acting as a gelling agent for both oil and water phases but also as a surfactant. The emulsification process is based on in-situ surfactant transfer. We characterize the emulsification process occurring at the nanoscale by using tensiometry experiments. The emulsion structure was determined by coupling Small Angle X-ray and neutron scattering, and confocal Raman microscopy.

FINDINGS

We demonstrate that the stability and unique rheological properties of these emulsions come from the presence of self-assembled crystalline structures of 12-hydroxystearic acid in both liquid phases. The emulsion properties can be tuned by varying the emulsion composition over a wide range. These gelled emulsions are prepared using a low energy method offering easy scale-up at an industrial level.

Novel aerogels based on supramolecular G-quadruplex assembly with intrinsic flame retardancy and thermal insulation

The construction of supramolecular aerogels still faces great challenges. Herein, we present a novel bio-based supramolecular aerogel derived from G-Quadruplex self-assembly of guanosine (G), boric acid (B) and sodium alginate (SA) and the obtained GBS aerogels exhibit superior flame-retardant and thermal insulating properties. The entire process involves environmentally friendly aqueous solvents and freeze-drying. Benefiting from the supramolecular self-assembly and interpenetrating dual network structures, GBS aerogels exhibit unique structures and sufficient self-supporting capabilities. The resulting GBS aerogels exhibit overall low densities (36.5-52.4 mg/cm3), and high porosities (>95 %). Moreover, GBS aerogels also illustrate excellent flame retardant and thermal insulating properties. With an oxygen index of 47.0-51.1 %, it can easily achieve a V-0 rating and low heat, smoke release during combustion. This work demonstrates the preparation of intrinsic flame-retardant aerogels derived from supramolecular self-assembly and dual cross-linking strategies, and is expected to provide an idea for the realization and application of novel supramolecular aerogel materials.

Control of the oil content of fried dough sticks through modulating structure change by reconstituted gluten fractions

In our study, we explored how gluten's role during dough formation and thermal processing can mitigate the adverse effects of physical factors on product quality. We discovered that a gluten network with a gliadin/glutenin ratio of 5:5 effectively limits oil penetration into the dough's core. This particular ratio is found to reduce the exposure of hydrophobic groups due to the presence of hydrated β-sheet structures. In contrast, gluten networks with higher gliadin proportions than typical wheat gluten tend to be looser, leading to increased chromophore exposure and facilitating more oil absorption. These observations highlighted the complex link between changes in gluten structure, varying protein compositions, and oil content in fried dough sticks. This research provided a foundation for developing specialized low-fat wheat flour and improving the quality of fried dough products.

Si-doped carbonized polymer dot as robust hydrophilic coating using for high efficiency antifogging

Hydrophilic coating can prevent surface from fogging but its application is limited by low mechanical performance. In this study, a hydrophilic coating was prepared by crosslinking the Si-doped carbonized polymer dot (Si-CPD) with 3-glycidyloxypropyltrimethoxysilane (GPTMS) and ethylene oxide (EO). The hydrophilic coating can be used as robust hydrophilic anti-fogging coating. The Si-CPD derived from ethylene diamine tetraacetic acid (EDTA) and aminopropyl oligosiloxanes (APOS) was successfully prepared via one-step hydrothermal method. Then, a resin solution was prepared by mixing Si-CPD, GPTMS and EO. Epoxy group of GPTMS and EO can react with amino group of Si-CPD. Finally, a composite coating with antifogging function can be obtained by simple heating curing. Due to the introduction of hydroxyl which derived from EO, the coating shows excellent antifogging performance. Meanwhile, the presence of inorganic component endows the coating with outstanding mechanical performance. The coating has great potential in related applications, such as optical lenses, mirrors and other transparency substrates.

In vitro digestion of starch and protein aerogels generated from defatted rice bran via supercritical carbon dioxide drying

This study investigated the in vitro digestibility of starch and protein aerogels produced from defatted rice bran (DRB), an underutilized rice processing byproduct, using supercritical carbon dioxide (SC-CO2) drying. The extracted starch (i.e., purified starch), crude starch, and proteins were used for the aerogel formation at 15% (w/w) concentration and further characterized. All aerogels exhibited three-dimensional open porous structures with high surface areas of 36-47 m2/g, densities lower than 0.3 g/cm3, and porosities higher than 84%. The starch hydrolyses in starch and crude starch aerogels were 86 and 73%, respectively, while the protein hydrolysis in protein aerogels reached up to 82% after sequential oral, gastric, and intestinal digestion. Thus, the hydrolysis rates achieved in simulated digestions suggest that the developed aerogels from DRB have the potential to serve as vehicles for delivering bioactive compounds and add value to the underutilized DRB.

Comparative analysis of millet bran nanocelluloses with various morphologies: Revealing differences in the formation mechanism and structure characteristics

To investigate the differences of nanocelluloses with various morphologies, ammonium persulphate (APS) oxidation, H3PO4 dissolution and regeneration, and ball milling combined with 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) as a medium were applied to isolate cellulose nanocrystals (MCNCs), cellulose nanospheres (MCNSs) and cellulose fibrils (MCNFs) from millet bran. The structure, properties, and formation mechanism of three nanocelluloses were comparatively investigated by Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, atomic force microscope, scanning electronic microscope, and emulsifying ability evaluation. MCNCs had needle-like structures due to the removal of amorphous regions, MCNFs appeared fibrous structures due to swelling and mechanical force, and MCNSs displayed spherical structures through self-assembly. MCNCs and MCNFs were confirmed to exhibit cellulose I structures with crystallinities of 61.24 % and 50.09 %, respectively. MCNSs showed the highest crystallinity of 68.41 % with a cellulose II structure. MCNFs and MCNSs exhibited higher initial decomposition temperatures, while MCNCs showed the highest residual mass. MCNFs suspension showed the highest apparent viscosity, while MCNSs suspension demonstrated superior dispersion. MCNSs-emulsion displayed the smallest droplet size, and MCNFs-emulsion exhibited the highest viscosity. This study reveals the formation mechanisms and relationship between morphologies and properties of three millet bran nanocelluloses, providing a theoretical basis for their application.

The influence of activity patterns and relative humidity on particle resuspension in classrooms

This paper investigates the impact of children's recess activity patterns on particulate matter (PM) resuspension in indoor environments, highlighting the complex, multi-dimensional nature of these activities and their interaction with environmental parameters. Despite the recognized role of indoor human activity in PM resuspension, research specifically addressing the effects of children's movements has been sparse. Through experimental scenarios that account for the characteristics of student activities, such as movement speed, trajectory, the number of participants, aisle widths, and varying humidity levels, this study uncovers significant differences in PM resuspension rates. It reveals that not only do movement speed and trajectory have a profound impact, but also the interaction between humidity and these factors plays a critical role, especially under lower humidity conditions. Additionally, the study demonstrates how the combination of people density and spatial configurations can significantly influence resuspension rates. The findings offer valuable insights for designing strategies to mitigate particle pollution in classrooms and similar indoor environments.

pH-responsive membranes: Mechanisms, fabrications, and applications

Understanding the mechanisms of pH-responsiveness allows researchers to design and fabricate membranes with specific functionalities for various applications. The pH-responsive membranes (PRMs) are particular categories of membranes that have an amazing aptitude to change their properties such as permeability, selectivity and surface charge in response to changes in pH levels. This review provides a brief introduction to mechanisms of pH-responsiveness in polymers and categorizes the applied polymers and functional groups. After that, different techniques for fabricating pH-responsive membranes such as grafting, the blending of pH-responsive polymers/microgels/nanomaterials, novel polymers and graphene-layered PRMs are discussed. The application of PRMs in different processes such as filtration membranes, reverse osmosis, drug delivery, gas separation, pervaporation and self-cleaning/antifouling properties with perspective to the challenges and future progress are reviewed. Lastly, the development and limitations of PRM fabrications and applications are compared to provide inclusive information for the advancement of next-generation PRMs with improved separation and filtration performance.

Enhanced separation of monovalent and divalent ions in high salinity wastewater by selective electrodialysis: Experimental investigation and performance prediction

To fulfill the industrial requirements of salt fractionation and recovery from saline wastewater, a two-chamber selective electrodialysis (SED) stack incorporating commercial monovalent selective anion exchange membranes was employed and investigated in this study. Three different initial concentration ratios of NaCl/Na2SO4, namely 1:1 (10 g/L:10 g/L), 3:1 (30 g/L:10 g/L), and 5:1 (50 g/L:10 g/L) were examined to simulate various scenarios of saline wastewater. The influence of applied current density on membrane selectivity and overall system efficiency was further evaluated. The results indicated that an increase in the NaCl fraction within the feed solution directly correlates with enhanced concentration and purity of Na2SO4 in the product, achieving purities exceeding 92 %. A lower current density contributed to improved concentration and purity of Na2SO4, whereas higher current densities were conducive to augmenting the concentration and purity of NaCl. Additionally, a linear correlation was observed between the volumetric water transport and NaCl migration. Through numerical simulations, the concentrations of Na2SO4 and NaCl in the effluent were predicted, facilitating a comparative analysis with the salt fractionation efficiency of commercial nanofiltration membranes. Subsequent assessments of energy consumption and current efficiency revealed that the SED system ensured high product concentration and purity at reasonably low energy consumption (0.22-0.28 kWh per kg NaCl) alongside a high current efficiency (83-89 %). These findings offer critical insights into the optimization of salt fractionation process and highlight its economic and technical feasibility for the sustainable management of industrial saline wastewater.

Advancements in nanoparticle-modified zeolites for sustainable water treatment: An interdisciplinary review

The contamination of water sources with heavy metals, dyes, and other pollutants poses significant challenges to environmental sustainability and public health. Traditional water treatment methods often exhibit limitations in effectively addressing these complex contaminants. In response, recent developments in nanotechnology have catalyzed the exploration of novel materials for water remediation, with nanoparticle-doped zeolites emerging as a promising solution. This comprehensive review synthesizes current literature on the integration of nanoparticles into zeolite frameworks for enhanced contaminant removal in water treatment applications. We delve into synthesis methodologies, elucidate mechanistic insights, and evaluate the efficacy of nanoparticle-doped zeolites in targeting specific pollutants, while also assessing considerations of material stability and environmental impact. The review underscores the superior adsorptive and catalytic properties of nanoparticle-doped zeolites, owing to their high surface area, tailored porosity, and enhanced ion-exchange capabilities. Furthermore, we highlight recent advancements in heavy metal and organic pollutant uptake facilitated by these materials. Additionally, we explore the catalytic degradation of contaminants through advanced oxidation processes, demonstrating the multifunctionality of nanoparticle-doped zeolites in water treatment. By providing a comprehensive analysis of existing research, this review aims to guide future developments in the field, promoting the sustainable utilization of nanoparticle-doped zeolites as efficient and versatile materials for water remediation endeavors.

A novel electropolymerized molecularly imprinted dual-mode sensor for bisphenol AF detection in pond mud

Recently, bisphenol AF (BPAF) as most commonly used bisphenol A analogs had the increasing higher level in the environment with unknown risks. Herein, a synchronous dual-mode sensor had been established based on differential pulse voltammetry (DPV) and electrochemiluminescence (ECL) for the detection of BPAF in pond mud. Firstly, the sensing molecularly imprinted polymer (MIP) films were prepared by electrochemical polymerization procedure with 3,4-ethoxylene dioxy thiophene (EDOT) as the functional monomer, BPAF as the template molecule and MXene as the supporting electrolyte. Due to unique characters of PEDOT and MXene, the constructed MIP films were stable and highly conductive. Meanwhile, zinc-doped bismuth sulfide quantum dots (Zn-Bi2S3 QDs) were synthesized as a nano-emitter to generate strong ECL signals in the MIP film. In the sensing process, a pulsed voltage applied to the PEDOT/MXene MIP film to generate both DPV and ECL signals for simultaneous dual-mode detection. Additionally, the liquid-liquid extraction with deep eutectic solvent (menthol: octanol 1:1) was used for the pre-concentration of the BPAF in the pond mud. Based on the sensing system, the ECL and DPV response showed the good linear relationships with the concentration of BPAF with the ranges of 0.01 μM-50 μM and 0.1 μM-50 μM and the detection limits of 0.0060 μM and 0.059 μM, respectively.

Centrosome-organized plasma membrane infoldings linked to growth of a cortical actin domain

Regulated cell shape change requires the induction of cortical cytoskeletal domains. Often, local changes to plasma membrane (PM) topography are involved. Centrosomes organize cortical domains and can affect PM topography by locally pulling the PM inward. Are these centrosome effects coupled? At the syncytial Drosophila embryo cortex, centrosome-induced actin caps grow into dome-like compartments for mitoses. We found the nascent cap to be a collection of PM folds and tubules formed over the astral centrosomal MT array. The localized infoldings require centrosome and dynein activities, and myosin-based surface tension prevents them elsewhere. Centrosome-engaged PM infoldings become specifically enriched with an Arp2/3 induction pathway. Arp2/3 actin network growth between the infoldings counterbalances centrosomal pulling forces and disperses the folds for actin cap expansion. Abnormal domain topography with either centrosome or Arp2/3 disruption correlates with decreased exocytic vesicle association. Together, our data implicate centrosome-organized PM infoldings in coordinating Arp2/3 network growth and exocytosis for cortical domain assembly.

Spectroscopic characterization of fluorite of Amba Dongar, Gujarat, India: Linking chemical composition with color

This work addresses the long-standing debate surrounding the origin of color variation in fluorite (CaF2) through a novel quantitative approach. By examining eight carefully selected fluorite samples having different hue of colors from the Amba Dongar mine in Gujarat, India, a rigorous quantitative analysis was conducted. This approach combined chemical compositional data and optical spectroscopic features to elucidate the relationship between elemental composition, concentration, and color variation in fluorite. Precise elemental concentration data for trace transition metals, alkali metals, and rare earth elements (REEs) were obtained through inductively coupled plasma mass spectroscopy (ICP-MS) analysis of powdered fluorite samples. Optical spectroscopic techniques, including UV-visible absorption, emission (photoluminescence and fluorescence), and Raman spectroscopy, were employed to capture characteristic spectral signatures for specific color of the study sample. The work unveils a strong correlation between specific elemental concentrations and observed spectral features, particularly influenced by alkaline metals, transition group elements, and REEs. Fluorite's optical absorption behavior lacks a clear pattern in UV and infrared wavelength ranges but correlates well with transition metal, alkaline element, and REE concentrations in visible wavelength regions, influencing coloration. Luminescent centers in the study fluorite samples correspond to specific REE concentrations, indicating a strong linkage between emission wavelengths with the presence of specific REE. UV-visible and fluorescence in fluorite result from trivalent REE or Eu2+ ions, with emission intensity affected by REE concentration and specific REE or combinations thereof. Raman spectroscopy identifies characteristic modes related to F-substitution and REE impurities, providing insights into fluorite's structural composition. This quantitative correlation between elemental composition and spectroscopic characteristics represents a novel contribution for understanding color variation mechanisms in fluorite. The comprehensive analysis of this present work underscores the intricate interplay of mineral composition, and element concentration particularly alkaline metals, transition group elements, and REEs, for variation in spectral signatures with variation in fluorite's visual attributes.

Spontaneous nanotube formation of an asymmetric glycolipid

Over the past decades, advances in lipid nanotechnology have shown that self-assembled lipid structures providing ease of preparation, chemical stability, and biocompatibility represent a landmark on the development of multidisciplinary technologies. Lipid nanotubes (LNTs) are a unique class of lipid self-assembled structures, bearing unique properties such as high-aspect ratio, tunable diameter size, and precise molecular recognition. They can be obtained either by the action of external factors to already formed vesicles or spontaneously, the latter depending strongly on subtle molecular features. Here, we report on the spontaneous formation of supported lipid nanotubes of a particular type of glycolipid, ohmline, whose hydrophobic core displays remarkable asymmetry. The combination of bulk and surface-sensitive techniques indicates that below its main transition, ohmline displays an interdigitated gel phase, likely driven by the unique asymmetry in its hydrophobic core. Enhanced order packing by interdigitation favors the formation of ohmline nanotubes in agreement with chiral-based models of nanotube formation. The findings presented in this work call for additional studies to link lipid molecular structure-assembly relationships, whose understanding is relevant for the controlled design of lipid nanotubes networks in particular and controlled design of soft-matter nanomaterials in general.

Transient paper-based electrochemical biosensor Fabricated by superadditive Cu-TCPP(Fe)/Mxene for Multipathway non-invasive, highly sensitive detection of Bodily metabolites

Current advances in non-invasive fluid diagnostics highlight unique benefits for monitoring metabolic diseases. However, the low concentrations and complex compositions of biomarkers in fluids such as sweat, urine, and saliva impose stringent demands on the sensitivity and stability of detection technologies. Here, we developed a high-sensitivity, low-cost instantaneous electrochemical sensor based on the superadditive effect mechanism of Cu-TCPP(Fe)/Mxene (MMs Paper-ECL Sensor), which has been successfully applied for the simultaneous real-time detection of glucose and uric acid. Strong interfacial interactions between Mxene and Cu-TCPP(Fe) were revealed through precise simulation calculations and multi-dimensional characterization analysis, significantly enhancing the sensor's electrocatalytic performance and reaction kinetics. Experimentally, this exceptional electrocatalytic activity was demonstrated in its unprecedented high sensitivity and wide linear detection range for glucose and uric acid, with a non-invasive linear range from 0.001 nM to 5 mM, 0.025 nM-5 mM, detection limits as low as 1.88 aM and 5.80 pM, and stability extending up to 100 days. This represents not only a breakthrough in sensitivity and stability but also provides an effective, low-cost solution that overcomes the limitations of existing electronic devices, enabling multi-channel simultaneous detection. The universality of this sensor holds vast potential for application in the field of non-invasive fluid diagnostics.

Effect of microbubbles on immersion freezing of grape tomato

Microbubbles (MBs) were incorporated into calcium chloride solution as a novel freezing medium for immersion freezing of grape tomato. The effects of MB size (39, 43, 48 μm mean diameter), entrapped gas (air, N2, CO2) and freezing temperature (-10, -15, -20 °C) on the freezing behavior and quality attributes of tomato were investigated. MBs increased the nucleation temperature from -7.4 to -3.5 °C and reduced the onset time of nucleation from 5.8 to 2.9 min at freezing temperature of -20 °C, which facilitated the formation of small ice crystals within tomato. MB-assisted freezing reduced the drip loss by 13.7-17.0% and improved the firmness of tomato, particularly when MB size and freezing temperature decreased. Freezing tomato with air-MBs did not compromise its nutritional quality, using N2- and CO2-MBs even increased its lycopene content, by 31% and 23%, respectively. The results proved the preservation effect of MBs on fruit during immersion freezing. This study can benefit the fruit and vegetable industry by providing an efficient freezing technology for producing frozen products with high sensory and nutritional quality.

Speciation, phytoavailability, and accumulation of toxic elements and sulfur by humic acid-fertilized lemongrass and common sage in a sandy soil treated with heavy oil fly ash: A trial for management of power stations wastes

Globally, power stations generate huge amounts of the hazardous waste heavy oil fly ash (HOFA), which is rich in Ni, V, Fe, S, and dumped into landfills. Thus, exploring new approaches for a safe recycling and sustainable management of HOFA is needed and of great environmental interest. The potential application of HOFA as an amendment to sandy soils has not been studied yet. This is the first research investigating the potentiality of using HOFA as a soil conditioner. To this end, we conducted a greenhouse experiment in order to investigate the impacts of HOFA addition (1.2, 2.4, 3.6 t ha-1) to sandy soil on the total and available content of nutrients (e.g., S, Fe, Mn, Cu, Zn) and toxic elements (TEs; e.g., Cd, Co, Cr, Ni, Pb, V) in the soil and their phytoextraction and translocation by lemongrass (Cymbopogon citratus) and common sage (Salvia officinalis). We also assessed the impact of humic acid (HA) foliar application (50 and 100 l ha-1) on the growth and elements accumulation by the two plants. The studied HOFA was acidic and highly enriched in S (43,268.0), V (3,527.0), Ni (1774.0), and Fe (15,159.0) (units in mg kg-1). The X-ray absorption near edge structure (XANES) data showed that V in HOFA was composed primarily of V(IV) sorbed onto goethite, V(V) sorbed onto humic substances, in the forms of V2O3, and VCl4. Addition of the lower doses of HOFA (1.2 and 2.4 t ha-1) did not change significantly soil pH, salinity, and the total and available elements content compared to the unamended soil. Although the elements content in the 3.6 t ha-1 HOFA-treated soil was significantly higher than the untreated, the total content of all elements (except for Ni) was lower than the maximum allowable concentrations in soils. HOFA addition, particularly in the highest dose (3.6 t ha-1), decreased significantly the growth and biomass of both plants. Common sage accumulated more elements than lemongrass; however, the elements content in the plants was lower than the critical concentrations for sensitive plants. The foliar application of humic acid enhanced significantly the plant growth and increased their tolerance to the HOFA-induced stress. We conclude that the addition of HOFA up to 2.4 t ha-1 in a single application as amendment to sandy soils is not likely to create any TE toxicity problems to plants, particularly if combined with a foliar application of humic acid; however, repeated additions of HOFA may induce toxicity. These findings should be verified under field conditions.

Quenching study of Cu2S-MPA/NGODs composites in electrochemiluminescence detection by modulating resonance energy transfer and adsorption process

This study explores the principles of resonance energy transfer and adsorption modulation using composites of Cu2S-MPA/NGODs. These composites can efficiently control the quenching process of electrochemiluminescence (ECL). Mercaptopropionic acid (MPA) was added during the synthesis of Cu2S-MPA to enhance its attachment to nitrogen-doped graphene quantum dots (NGODs). The UV absorption peaks of NGODs coincided with the emission peaks of luminol ECL, enabling resonance energy transfer and enhancing the quenching capability of Cu2S-MPA. Meanwhile, there is another quenching strategy. When the readily reducible Cu+ ions underwent partial reduction to Cu when they were bound to NGODs. This weakened the electrocatalytic effect on reactive oxygen species (ROS) and had a detrimental impact on electron transfer. Under optimal conditions, the immunosensor ECL intensity decreased linearly with the logarithm of carcinoembryonic antigen (CEA) concentration in the range of 0.00001-40 ng/mL, with a detection limit of 0.269 fg/mL. The sensor was effectively utilized for the identification of CEA in actual serum samples.

Multi-output neural network model for predicting biochar yield and composition

In biomass pyrolysis for biochar production, existing prediction models face computational challenges and limited accuracy. This study curated a comprehensive dataset, revealing pyrolysis parameters' dominance in biochar yield (54.8 % importance). Pyrolysis temperature emerged as pivotal (PCC = -0.75), influencing yield significantly. Artificial Neural Network (ANN) outperformed Random Forest (RF) in testing set predictions (R2 = 0.95, RMSE = 3.6), making it apt for complex multi-output predictions and software development. The trained ANN model, employed in Partial Dependence Analysis, uncovered nonlinear relationships between biomass characteristics and biochar yield. Findings indicated optimization opportunities, correlating low pyrolysis temperatures, elevated nitrogen content, high fixed carbon, and brief residence times with increased biochar yields. A multi-output ANN model demonstrated optimal fit for biochar yield. A user-friendly Graphical User Interface (GUI) for biochar synthesis prediction was developed, exhibiting robust performance with a mere 0.52 % prediction error for biochar yield. This study showcases practical machine learning application in biochar synthesis, offering valuable insights and predictive tools for optimizing biochar production processes.

Unlocking the potential of Extensin Signal peptide and Elastin-like polypeptide tag fused to Shigella dysenteriae's IpaDSTxB to improve protein expression and purification in Nicotiana tabacum and Medicagosativa

Plants are often seen as a potent tool in the recombinant protein production industry. However, unlike bacterial expression, it is not a popular method due to the low yield and difficulty of protein extraction and purification. Therefore, developing a new high efficient and easy to purify platform is crucial. One of the best approaches to make extraction easier is to utilize the Extensin Signal peptide (EXT) to translocate the recombinant protein to the outside of the cell, along with incorporating an Elastin-like polypeptide tag (ELP) to enhance purification and accumulation rates. In this research, we transiently expressed Shigella dysenteriae's IpaDSTxB fused to both NtEXT and ELP in both Nicotiana tabacum and Medicago sativa. Our results demonstrated that N. tabacum, with an average yield of 6.39 ng/μg TSP, outperforms M. sativa, which had an average yield of 3.58 ng/μg TSP. On the other hand, analyzing NtEXT signal peptide indicated that merging EXT to the constructs facilitates translocation of IpaDSTxB to the apoplast by 78.4% and 65.9% in N. tabacum and M. sativa, respectively. Conversely, the mean level for constructs without EXT was below 25% for both plants. Furthermore, investigation into the orientation of ELP showed that merging it to the C-terminal of IpaDSTxB leads to a higher accumulation rate in both N. tabacum and M. sativa by 1.39 and 1.28 times, respectively. It also facilitates purification rate by over 70% in comparison to 20% of the 6His tag. The results show a highly efficient and easy to purify platform for the expression of heterologous proteins in plant.

Surface roughness influence on extracellular electron microbiologically influenced corrosion of C1018 carbon steel by Desulfovibrio ferrophilus IS5 biofilm

Carbon steel microbiologically influenced corrosion (MIC) by sulfate reducing bacteria (SRB) is known to occur via extracellular electron transfer (EET). A higher biofilm sessile cell count leads to more electrons being harvested for sulfate reduction by SRB in energy production. Metal surface roughness can impact the severity of MIC by SRB because of varied biofilm attachment. C1018 carbon steel coupons (1.2 cm2 top working surface) polished to 36 grit (4.06 μm roughness which is relatively rough) and 600 grit (0.13 μm) were incubated in enriched artificial seawater inoculated with highly corrosive Desulfovibrio ferrophilus IS5 at 28 ℃ for 7 d and 30 d. It was found that after 7 d of SRB incubation, 36 grit coupons had a 11% higher sessile cell count at (2.0 ± 0.17) × 108 cells/cm2, 52% higher weight loss at 22.4 ± 5.9 mg/cm2 (1.48 ± 0.39 mm/a uniform corrosion rate), and 18% higher maximum pit depth at 53 μm compared with 600 grit coupons. However, after 30 d, the differences diminished. Electrochemical tests with transient information supported the weight loss data trends. This work suggests that a rougher surface facilitates initial biofilm establishment but provides no long-term advantage for increased biofilm growth.

Real-time imaging of decompression gas bubble growth in the spinal cord of live rats

PURPOSE

To observe the growth and resolution of decompression gas bubbles in the spinal cord of live rats in real time using MRI.

METHODS

We constructed an MRI-compatible pressure chamber system to visualize gas bubble dynamics in deep tissues in real time. The system pressurizes and depressurizes rodents inside an MRI scanner and monitors their respiratory rate, heart rate, and body temperature while providing gaseous anesthesia under pressure during the experiments.

RESULTS

We observed the formation of decompression gas bubbles in the spinal cord of rats after compression to 7.1 bar absolute and rapid decompression inside the MRI scanner while maintaining continuous gaseous anesthesia and vital monitoring.

CONCLUSION

We have shown the direct observation of decompression gas bubble formation in real time by MRI in live, anesthetized rats.