Insight into catalytic performance and reaction mechanism for toluene total oxidation over Cu-Ce supported catalyst

Herein, three supported catalysts, CuO/Al2O3, CeO2/Al2O3, and CuO-CeO2/Al2O3, were synthesized by the convenient impregnation method to reveal the effect of CeO2 addition on catalytic performance and reaction mechanism for toluene oxidation. Compared with CuO/Al2O3, the T50 and T90 (the temperatures at 50% and 90% toluene conversion, respectively) of CuO-CeO2/Al2O3 were reduced by 33 and 39 °C, respectively. N2 adsorption-desorption experiment, XRD, SEM, EDS mapping, Raman, EPR, H2-TPR, O2-TPD, XPS, NH3-TPD, Toluene-TPD, and in-situ DRIFTS were conducted to characterize these catalysts. The excellent catalytic performance of CuO-CeO2/Al2O3 could be attributed to its strong copper-cerium interaction and high oxygen vacancies concentration. Moreover, in-situ DRIFTS proved that CuO-CeO2/Al2O3 promoted the conversion of toluene to benzoate and accelerated the deep degradation path of toluene. This work provided valuable insights into the development of efficient and economical catalysts for volatile organic compounds.

Ce-doped TiO2 supported RuO2 as efficient catalysts for the oxidation of HCl to Cl2

Reducing the cost of RuO2/TiO2 catalysts is still one of the urgent challenges in catalytic HCl oxidation. In the present work, a Ce-doped TiO2 supported RuO2 catalyst with a low Ru loading was developed, showing a high activity in the catalytic oxidation of HCl to Cl2. The results on some extensive characterizations of both Ce-doped TiO2 carriers and their supported RuO2 catalysts show that the doping of Ce into TiO2 can effectively change the lattice parameters of TiO2 to improve the dispersion of the active RuO2 species on the carrier, which facilitates the production of surface Ru species to expose more active sites for boosting the catalytic performance even under some harsh reaction conditions. This work provides some scientific basis and technical support for chlorine recycling.

Insight into the bimetallic structure sensibility of catalytic nitrate reduction over Pd-Cu nanocrystals

Catalytic reduction of nitrate over bimetallic catalysts has emerged as a technology for sustainable treatment of nitrate-containing groundwater. However, the structure of bimetallic has been much less investigated for catalyst optimization. Herein, two main types of Pd-Cu bimetallic nanocrystal structures, heterostructure and intermetallic, were prepared and characterized using high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The results show that two individual Pd and Cu nanocrystals with a mixed interface exist in the heterostructure nanocrystals, while Pd and Cu atoms are uniformly distributed across the intermetallic Pd-Cu nanocrystals. The catalytic nitrate reduction experiments were carried out in a semibatch reactor under constant hydrogen flow. The nitrate conversion rate of the heterostructure Pd-Cu nanocrystals supported on α-Al2O3, γ-Al2O3, SBA-15, and XC-72R exhibited 3.82-, 6.76-, 4.28-, 2.44-fold enhancements relative to the intermetallic nanocrystals, and the nitrogen and nitrite were the main products for the heterostructure and intermetallic Pd-Cu nanocrystals, respectively. This indicates that the catalytic nitrate reduction over Pd-Cu catalyst is sensitive to the bimetallic structures of the catalysts, and heterostructure bimetallic nanocrystals exhibit better catalytic performances on both the activity and selectivity, which may provide new insights into the design and optimization of catalysts to improve catalytic activity and selectivity for nitrate reduction in water.

Tailored design of novel Co0-Coδ+ dual phase nanoparticles for selective CO2 hydrogenation to ethanol

Catalytic hydrogenation of CO2 to ethanol is a promising solution to address the greenhouse gas (GHG) emissions, but many current catalysts face efficiency and cost challenges. Cobalt based catalysts are frequently examined due to their abundance, cost-efficiency, and effectiveness in the reaction, where managing the Co0 to Coδ+ ratio is essential. In this study, we adjusted support nature (Al2O3, MgO-MgAl2O4, and MgO) and reduction conditions to optimize this balance of Co0 to Coδ+ sites on the catalyst surface, enhancing ethanol production. The selectivity of ethanol reached 17.9% in a continuous flow fixed bed micro-reactor over 20 mol% Co@MgO-MgAl2O4 (CoMgAl) catalyst at 270 °C and 3.0 MPa, when reduced at 400 °C for 8 h. Characterisation results coupled with activity analysis confirmed that mild reduction condition (400 °C, 10% H2 balance N2, 8 h) with intermediate metal support interaction favoured the generation of partially reduced Co sites (Coδ+ and Co0 sites in single atom) over MgO-MgAl2O4 surface, which promoted ethanol synthesis by coupling of dissociative (CHx*)/non-dissociative (CHxO*) intermediates, as confirmed by density functional theory analysis. Additionally, the CoMgAl, affordably prepared through the coprecipitation method, offers a potential alternative for CO2 hydrogenation to yield valuable chemicals.

Structure-phase transformation of bismuth oxide to BiOCl/Bi24O31Cl10 shoulder-by-shoulder heterojunctions for efficient photocatalytic removal of antibiotic

Developing heterojunction photocatalyst with well-matched interfaces and multiple charge transfer paths is vital to boost carrier separation efficiency for photocatalytic antibiotics removal, but still remains a great challenge. In present work, a new strategy of chloride anion intercalation in Bi2O3 via one-pot hydrothermal process is proposed. The as-prepared Ta-BiOCl/Bi24O31Cl10 (TBB) heterojunctions are featured with Ta-Bi24O31Cl10 and Ta-BiOCl lined shoulder-by-shouleder via semi-coherent interfaces. In this TBB heterojunctions, the well-matched semi-coherent interfaces and shoulder-by-shoulder structures provide fast electron transfer and multiple transfer paths, respectively, leading to enhanced visible light response and improved photogenerated charge separation. Meanwhile, a type-II heterojunction for photocharge separation has been obtained, in which photogenerated electrons are drove from the CB (conduction band) of Ta-Bi24O31Cl10 to the both of bilateral empty CB of Ta-BiOCl and gathered on the CB of Ta-BiOCl, while the photogenerated holes are left on the VB (valence band) of Ta-Bi24O31Cl10, effectively hindering the recombination of photogenerated electron-hole pairs. Furthermore, the separated electrons can effectively activate dissolved oxygen for the generation of reactive oxygen species (·O2-). Such TBB heterojunctions exhibit remarkably superior photocatalytic degradation activity for tetracycline hydrochloride (TCH) solution to Bi2O3, Ta-BiOCl and Ta-Bi24O31Cl10. This work not only proposes a Ta-BiOCl/Bi24O31Cl10 shoulder-by-shoulder micro-ribbon architectures with semi-coherent interfaces and successive type-II heterojunction for highly efficient photocatalytic activity, but offers a new insight into the design of highly efficient heterojunction through phase-structure synergistic transformation strategy.

Spatial confinement: An effective strategy to improve H2O and SO2 resistance of the expandable graphite-modified TiO2-supported Pt nanocatalysts for CO oxidation

The expandable graphite (EG) modified TiO2 nanocomposites were prepared by the high shear method using the TiO2 nanoparticles (NPs) and EG as precursors, in which the amount of EG doped in TiO2 was 10 wt.%. Followed by the impregnation method, adjusting the pH of the solution to 10, and using the electrostatic adsorption to achieve spatial confinement, the Pt elements were mainly distributed on the exposed TiO2, thus generating the Pt/10EG-TiO2-10 catalyst. The best CO oxidation activity with the excellent resistance to H2O and SO2 was obtained over the Pt/10EG-TiO2-10 catalyst: CO conversion after 36 hr of the reaction was ca. 85% under the harsh condition of 10 vol.% H2O and 100 ppm SO2 at a high gaseous hourly space velocity (GHSV) of 400,000 hr-1. Physicochemical properties of the catalysts were characterized by various techniques. The results showed that the electrostatic adsorption, which riveted the Pt elements mainly on the exposed TiO2 of the support surface, reduced the dispersion of Pt NPs on EG and achieved the effective dispersion of Pt NPs, hence significantly improving CO oxidation activity over the Pt/10EG-TiO2-10 catalyst. The 10 wt.% EG doped in TiO2 caused the TiO2 support to form a more hydrophobic surface, which reduced the adsorption of H2O and SO2 on the catalyst, greatly inhibited deposition of the TiOSO4 and formation of the PtSO4 species as well as suppressed the oxidation of SO2, thus resulting in an improvement in the resistance to H2O and SO2 of the Pt/10EG-TiO2-10 catalyst.

Cu/TiO2 adsorbents modified by air plasma for adsorption-oxidation of H2S

In this study, non-thermal plasma (NTP) was employed to modify the Cu/TiO2 adsorbent to efficiently purify H2S in low-temperature and micro-oxygen environments. The effects of Cu loading amounts and atmospheres of NTP treatment on the adsorption-oxidation performance of the adsorbents were investigated. The NTP modification successfully boosted the H2S removal capacity to varying degrees, and the optimized adsorbent treated by air plasma (Cu/TiO2-Air) attained the best H2S breakthrough capacity of 113.29 mg H2S/gadsorbent, which was almost 5 times higher than that of the adsorbent without NTP modification. Further studies demonstrated that the superior performance of Cu/TiO2-Air was attributed to increased mesoporous volume, more exposure of active sites (CuO) and functional groups (amino groups and hydroxyl groups), enhanced Ti-O-Cu interaction, and the favorable ratio of active oxygen species. Additionally, the X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) results indicated the main reason for the deactivation was the consumption of the active components (CuO) and the agglomeration of reaction products (CuS and SO42-) occupying the active sites on the surface and the inner pores of the adsorbents.

Characteristics of catalytic destruction of dichloromethane and ethyl acetate mixture over HxPO4-RuOx/CeO2 catalyst

Catalytic destruction is an ascendant technology for the abatement of volatile organic compounds (VOCs) originating from solvent-based industrial processes. The varied composition tends to influence each VOC's catalytic behavior in the reaction mixture. We investigated the catalytic destruction of multi-component VOCs including dichloromethane (DCM) and ethyl acetate (EA), as representatives from pharmaceutical waste gases, over co-supported HxPO4-RuOx/CeO2 catalyst. A mutual inhibitory effect relating to concentrations because of competitive adsorption was verified in the binary VOCs oxidation and EA posed a more negative effect on DCM oxidation owing to EA's superior adsorption capacity. Preferential adsorption of EA on acidic sites (HxPO4/CeO2) promoted DCM activation on basic sites (O2-) and the dominating EA oxidation blocked DCM's access to oxidation centers (RuOx/CeO2), resulting in boosted monochloromethane yield and increased chlorine deposition for DCM oxidation. The impaired redox ability of Ru species owing to chlorine deposition in turn jeopardized deep oxidation of EA and its by-products, leading to increased gaseous by-products such as acetic acid originating from EA pyrolysis. Notably, DCM at low concentration slightly promoted EA conversion at low temperatures with or without water, consistent with the enhanced EA adsorption in co-adsorption analyses. This was mainly due to that DCM impeded the shielding effect of hydrolysate deposition from rapid EA hydrolysis depending on the decreased acidity. Moreover, water benefited EA hydrolysis but decreased CO2 selectivity while the generated water derived from EA was likely to affect DCM transformation. This work may provide theoretical guidance for the promotion of applied catalysts toward industrial applications.

Investigation into enhanced performance of toluene and Hg0 stimulative abatement over Cr-Mn oxides co-modified columnar activated coke

In this study, a string of Cr-Mn co-modified activated coke catalysts (XCryMn1-y/AC) were prepared to investigate toluene and Hg0 removal performance. Multifarious characterizations including XRD, TEM, SEM, in situ DRIFTS, BET, XPS and H2-TPR showed that 4%Cr0.5Mn0.5/AC had excellent physicochemical properties and exhibited the best toluene and Hg0 removal efficiency at 200℃. By varying the experimental gas components and conditions, it was found that too large weight hourly space velocity would reduce the removal efficiency of toluene and Hg0. Although O2 promoted the abatement of toluene and Hg0, the inhibitory role of H2O and SO2 offset the promoting effect of O2 to some extent. Toluene significantly inhibited Hg0 removal, resulting from that toluene was present at concentrations orders of magnitude greater than mercury's or the catalyst was more prone to adsorb toluene, while Hg0 almost exerted non-existent influence on toluene elimination. The mechanistic analysis showed that the forms of toluene and Hg0 removal included both adsorption and oxidation, where the high-valent metal cations and oxygen vacancy clusters promoted the redox cycle of Cr3+ + Mn3+/Mn4+ ↔ Cr6+ + Mn2+, which facilitated the conversion and replenishment of reactive oxygen species in the oxidation process, and even the CrMn1.5O4 spinel structure could provide a larger catalytic interface, thus enhancing the adsorption/oxidation of toluene and Hg0. Therefore, its excellent physicochemical properties make it a cost-effective potential industrial catalyst with outstanding synergistic toluene and Hg0 removal performance and preeminent resistance to H2O and SO2.

Iron-promoted zirconia-alumina supported Ni catalyst for highly efficient and cost-effective hydrogen production via dry reforming of methane

Developing cost-effective and high-performance catalyst systems for dry reforming of methane (DRM) is crucial for producing hydrogen (H2) sustainably. Herein, we investigate using iron (Fe) as a promoter and major alumina support in Ni-based catalysts to improve their DRM performance. The addition of iron as a promotor was found to add reducible iron species along with reducible NiO species, enhance the basicity and induce the deposition of oxidizable carbon. By incorporating 1 wt.% Fe into a 5Ni/10ZrAl catalyst, a higher CO2 interaction and formation of reducible "NiO-species having strong interaction with support" was observed, which led to an ∼80% H2 yield in 420 min of Time on Stream (TOS). Further increasing the Fe content to 2wt% led to the formation of additional reducible iron oxide species and a noticeable rise in H2 yield up to 84%. Despite the severe weight loss on Fe-promoted catalysts, high H2 yield was maintained due to the proper balance between the rate of CH4 decomposition and the rate of carbon deposit diffusion. Finally, incorporating 3 wt.% Fe into the 5Ni/10ZrAl catalyst resulted in the highest CO2 interaction, wide presence of reducible NiO-species, minimum graphitic deposit and an 87% H2 yield. Our findings suggest that iron-promoted zirconia-alumina-supported Ni catalysts can be a cheap and excellent catalytic system for H2 production via DRM.

Unveiling the photocatalytic marvels: Recent advances in solar heterojunctions for environmental remediation and energy harvesting

In the quest for effective solutions to address Environ. Pollut. and meet the escalating energy demands, heterojunction photocatalysts have emerged as a captivating and versatile technology. These photocatalysts have garnered significant interest due to their wide-ranging applications, including wastewater treatment, air purification, CO2 capture, and hydrogen generation via water splitting. This technique harnesses the power of semiconductors, which are activated under light illumination, providing the necessary energy for catalytic reactions. With visible light constituting a substantial portion (46%) of the solar spectrum, the development of visible-light-driven semiconductors has become imperative. Heterojunction photocatalysts offer a promising strategy to overcome the limitations associated with activating semiconductors under visible light. In this comprehensive review, we present the recent advancements in the field of photocatalytic degradation of contaminants across diverse media, as well as the remarkable progress made in renewable energy production. Moreover, we delve into the crucial role played by various operating parameters in influencing the photocatalytic performance of heterojunction systems. Finally, we address emerging challenges and propose novel perspectives to provide valuable insights for future advancements in this dynamic research domain. By unraveling the potential of heterojunction photocatalysts, this review contributes to the broader understanding of their applications and paves the way for exciting avenues of exploration and innovation.

Synthesis of δ-MnO2 via ozonation routine for low temperature formaldehyde removal

Nowadays, it is still a challenge to prepared high efficiency and low cost formaldehyde (HCHO) removal catalysts in order to tackle the long-living indoor air pollution. Herein, δ-MnO2 is successfully synthesized by a facile ozonation strategy, where Mn2+ is oxidized by ozone (O3) bubble in an alkaline solution. It presents one of the best catalytic properties with a low 100% conversion temperature of 85°C for 50 ppm of HCHO under a GHSV of 48,000 mL/(g·hr). As a comparison, more than 6 times far longer oxidation time is needed if O3 is replaced by O2. Characterizations show that ozonation process generates a different intermediate of tetragonal β-HMnO2, which would favor the quick transformation into the final product δ-MnO2, as compared with the relatively more thermodynamically stable monoclinic γ-HMnO2 in the O2 process. Finally, HCHO is found to be decomposed into CO2 via formate, dioxymethylene and carbonate species as identified by room temperature in-situ diffuse reflectance infrared fourier transform spectroscopy. All these results show great potency of this facile ozonation routine for the highly active δ-MnO2 synthesis in order to remove the HCHO contamination.

Enhanced Cd2+ removal from aqueous solution using olivine and magnesite combination: New insights into the mechanochemical synergistic effect

In this study, an efficient stabilizer material for cadmium (Cd2+) treatment was successfully prepared by simply co-milling olivine with magnesite. Several analytical methods including XRD, TEM, SEM and FTIR, combined with theoretical calculations (DFT), were used to investigate mechanochemical interfacial reaction between two minerals, and the reaction mechanism of Cd removal, with ion exchange between Cd2+ and Mg2+ as the main pathway. A fixation capacity of Cd2+ as high as 270.61 mg/g, much higher than that of the pristine minerals and even the individual/physical mixture of milled olivine and magnesite, has been obtained at optimized conditions, with a neutral pH value of the solution after treatment to allow its direct discharge. The as-proposed Mg-based stabilizer with various advantages such as cost benefits, green feature etc., will boosts the utilization efficiency of natural minerals over the elaborately prepared adsorbents.

The profound review of Fenton process: What's the next step?

Fenton and Fenton-like processes, which could produce highly reactive species to degrade organic contaminants, have been widely used in the field of wastewater treatment. Therein, the chemistry of Fenton process including the nature of active oxidants, the complicated reactions involved, and the behind reason for its strongly pH-dependent performance, is the basis for the application of Fenton and Fenton-like processes in wastewater treatment. Nevertheless, the conflicting views still exist about the mechanism of the Fenton process. For instance, reaching a unanimous consensus on the nature of active oxidants (hydroxyl radical or tetravalent iron) in this process remains challenging. This review comprehensively examined the mechanism of the Fenton process including the debate on the nature of active oxidants, reactions involved in the Fenton process, and the behind reason for the pH-dependent degradation of contaminants in the Fenton process. Then, we summarized several strategies that promote the Fe(II)/Fe(III) cycle, reduce the competitive consumption of active oxidants by side reactions, and replace the Fenton reagent, thus improving the performance of the Fenton process. Furthermore, advances for the future were proposed including the demand for the high-accuracy identification of active oxidants and taking advantages of the characteristic of target contaminants during the degradation of contaminants by the Fenton process.

A review of functions and mechanisms of clay soil conditioners and catalysts in thermal remediation compared to emerging photo-thermal catalysis

High temperatures and providing sufficient time for the thermal desorption of persistent organic pollutants (POPs) from contaminated clay soils can lead to intensive energy consumption. Therefore, this article provides a critical review of the potential additives which can improve soil texture and increase the volatility of POPs, and then discusses their enhanced mechanisms for contributing to a green economy. Ca-based additives have been used to reduce plasticity of bentonite clay, absorb water and replenish system heat. In contrast, non-Ca-based additives have been used to decrease the plasticity of kaolin clay. The soil structure and soil plasticity can be changed through cation exchange and flocculation processes. The transition metal oxides and alkali metal oxides can be applied to catalyze and oxidize polycyclic aromatic hydrocarbons, petroleum and emerging contaminants. In this system, reactive oxygen species (•O2- and •OH) are generated from thermal excitation without strong chemical oxidants. Moreover, multiple active ingredients in recycled solid wastes can be controlled to reduce soil plasticity and enhance thermal catalysis. Alternatively, the alkali, nano zero-valent iron and nano-TiN can catalyze hydrodechlorination of POPs under reductive conditions. Especially, photo and photo-thermal catalysis are discussed to accelerate replacement of fossil fuels by renewable energy in thermal remediation.

Bamboo-like MnO2⋅Co3O4: High-performance catalysts for the oxidative removal of toluene

The manganese-cobalt mixed oxide nanorods were fabricated using a hydrothermal method with different metal precursors (KMnO4 and MnSO4·H2O for MnOx and Co(NO3)2⋅6H2O and CoCl2⋅6H2O for Co3O4). Bamboo-like MnO2⋅Co3O4 (B-MnO2⋅Co3O4 (S)) was derived from repeated hydrothermal treatments with Co3O4@MnO2 and MnSO4⋅H2O, whereas Co3O4@MnO2 nanorods were derived from hydrothermal treatment with Co3O4 nanorods and KMnO4. The study shows that manganese oxide was tetragonal, while the cobalt oxide was found to be cubic in the crystalline arrangement. Mn surface ions were present in multiple oxidation states (e.g., Mn4+ and Mn3+) and surface oxygen deficiencies. The content of adsorbed oxygen species and reducibility at low temperature declined in the sequence of B-MnO2⋅Co3O4 (S) > Co3O4@MnO2 > MnO2 > Co3O4, matching the changing trend in activity. Among all the samples, B-MnO2⋅Co3O4 (S) showed the preeminent catalytic performance for the oxidation of toluene (T10% = 187°C, T50% = 276°C, and T90% = 339°C). In addition, the B-MnO2⋅Co3O4 (S) sample also exhibited good H2O-, CO2-, and SO2-resistant performance. The good catalytic performance of B-MnO2⋅Co3O4 (S) is due to the high concentration of adsorbed oxygen species and good reducibility at low temperature. Toluene oxidation over B-MnO2⋅Co3O4 (S) proceeds through the adsorption of O2 and toluene to form O*, OH*, and H2C(C6H5)* species, which then react to produce benzyl alcohol, benzoic acid, and benzaldehyde, ultimately converting to CO2 and H2O. The findings suggest that B-MnO2⋅Co3O4 (S) has promising potential for use as an effective catalyst in practical applications.

Efficient dry reforming of methane realized by photoinduced acceleration of oxygen migration rate

Methane dry reforming (DRM) can consume greenhouse gases (CH4 and CO2) to produce valuable Fischer-Tropsch syngas (CO and H2). However, conventional thermally driven DRM consume large amounts of energy and face problems such as catalyst sintering and carbon deposition leading to insufficient catalytic activity. In this study, a photothermal synergistic TiO2/CeO2/Ru catalyst with high efficiency was designed. Under the light condition, the yields of H2 and CO reached 496.3 mmol g-1 h-1 and 522.4 mmol g-1 h-1, respectively. In addition, the catalyst demonstrated excellent stability after 100 h cyclic stability test. In-situ X-ray photoelectron spectroscopy (IS-XPS) and density functional theory (DFT) calculations revealed that the heterojunction interface formed by TiO2/CeO2/Ru is favourable for capturing photogenerated electrons and suppressing the recombination rate of photons and holes, thus improving the photocatalytic performance. Furthermore, light-induced metal-to-metal charge transfer (MMCT) accelerated oxygen migration, which not only improved the catalytic activity, but also suppressed the formation of carbon deposits on the catalyst surface, thereby enhancing the cycling stability. This study explores the mechanism of photothermally synergistic DRM, which provides a new pathway for the efficient use of solar energy.

Tailoring local electron density and molecular oxygen activation behavior via potassium/halogen co-tuned graphitic carbon nitride for enhanced photocatalytic activity

Graphite carbon nitride (g-C3N4) is a promising photocatalyst,but its inadequate reactive sites, weak visible light responsiveness, and sluggish separation of photogenerated carriers hamperthe improvement of photodegradation efficiency. In this work, potassium (K) and halogen atoms co-modified g-C3N4 photocatalysts (CN-KX, X = F, Cl, Br, I) were constructed to adjust the electrical and band structure for enhanced generation of reactive oxygen species. Through an integration of theoretical calculation and experimental exploration, the doping sites of halogen atoms as well as the evolution of crystal, band, and electronic structures were investigated. The results show that a covalent bond is formed between the F atom and the C atom, substitution of the N atom occurs with a Cl atom, and doping of Br, I, or K atoms takes place at the interstitial site. CN-KX photocatalysts exhibits lower band gap, faster photogenerated electron migration, and enhanced photocatalytic activity. Specifically, the CN-KI photocatalyst exhibits the highest photodegradation efficiency because of its smaller interplanar spacing, formation of the midgap state, and adjustable local electron density. Equally, the doping of I atom not only provides a stable adsorption site for oxygen (O2) but also facilitates electron transfer, promoting the production of superoxide radicals (O2-) and contributing to the process of photodegradation.

Oxygen-bridged Schottky junction in ZnO-Ni3ZnC0.7 promotes photocatalytic reduction of CO2 to CO: Steering charge flow and modulating electron density of active sites

Developing carbon dioxide (CO2) photocatalysts from transition metal carbides (TMCs) with abundant active sites, modulable electron cloud density, as well as low cost and high stability is of great significance for artificial photosynthesis. Building an efficient electron transfer channel between the photo-excitation site and the reaction-active site to extract and steer photo-induced electron flow is necessary but challenging for the highly selective conversion of CO2. In this study, we achieved an oxygen-bridged Schottky junction between ZnO and Ni3ZnC0.7 (denoted as Znoxide-O-ZnTMC) through a ligand-vacancy strategy of MOF. The ZnO-Ni3ZnC0.7 heterostructure integrates the photo-exciter (ZnO), high-speed electron transport channel (Znoxide-O-ZnTMC), and reaction-active species (Ni3ZnC0.7), where Znoxide-O-ZnTMC facilitates the transfer of excited electrons in ZnO to Ni3ZnC0.7. The Zn atoms in Ni3ZnC0.7 serve as electron-rich active sites, regulating the CO2 adsorption energy, promoting the transformation of *COOH to CO, and inhibiting H2 production. The ZnO-Ni3ZnC0.7 shows a high CO yield of 2674.80 μmol g-1h-1 with a selectivity of 93.40 % and an apparent quantum yield of 18.30 % (λ = 420 nm) with triethanolamine as a sacrificial agent. The CO production rate remains at 96.40 % after 18 h. Notably, ZnO-Ni3ZnC0.7 exhibits a high CO yield of 873.60 μmol g-1h-1 with a selectivity of 90.20 % in seawater.

Unlocking the critical roles of N, P Co-Doping in MXene for Lithium-Oxygen Batteries: Elevated d-Band center and expanded interlayer spacing

The design and fabrication of bifunctional catalysts with high electrocatalytic activity and stability are critical for developing highly reversible Li-O2 batteries (LOBs). Herein, the N, P co-doped MXene (NP-MXene) is prepared by one-step annealing method and evaluated as bifunctional catalyst for LOBs. The results suggest that the P doping plays a crucial role in increasing interlayer distance of MXene, thereby effectively providing more active sites, fast mass transfer, and ample space for the deposition/decomposition of Li2O2. Moreover, the N doping can significantly elevate the d-band center of Ti, thereby remarkably improving the adsorption of reaction intermediates and accelerating the deposition/decomposition of Li2O2 films. Consequently, the MXene-based LOBs deliver an ultrahigh specific capacity of 13,995 mAh/g at 500 mA g-1, a discharge/charge voltage gap of 0.89 V, and a cycle life up to 523 cycles with a limited capacity of 1000 mAh/g at 500 mA g-1. Impressively, the as-fabricated flexible LOBs with NP-MXene cathode display excellent cycling stability and ability to continuously power LEDs even after bending. Our findings pave the road of heteroatom doped MXenes as next-generation electrodes for high-performance energy storage and conversion systems.

Harnessing photocatalytic activity of mesoporous graphitic carbon nitride decorated by copper single-atom catalysts for oxidative dehydrogenation of N-heterocycles

This work describes the application of Cu single-atom catalysts (SACs) for photocatalytic oxidative dehydrogenation of N-heterocyclic amines to the respective N-heteroaromatics through environmentally benign and sustainable pathways. The mesoporous graphitic carbon nitride (mpg-C3N4), prepared by the one-step pyrolysis method, possesses a lightweight material with a high surface area (95 m2 g-1) and an average pore diameter (3.6 nm). A simple microwave-assisted preparation method was employed to decorate Cu single-atom over mpg-C3N4 support. The Cu single-atom decorated on mpg-C3N4 support (Cu@mpg-C3N4) is characterized by various characterization techniques, including XRD, UV-visible spectrophotometry, HRTEM, HAADF-STEM with elemental mapping, AC-STEM, ICP-OES, XANES, EXAFS, and BET surface area. These characterization studies confirmed that the Cu@mpg-C3N4 catalyst exhibited high surface area, mesoporous nature, medium band gap, and low metal loading. The as-synthesized and well-characterized Cu@mpg-C3N4 single-atom photocatalyst is then evaluated for its efficacy in converting N-heterocycles into corresponding N-heteroaromatic compounds with excellent conversion and selectivity (>99 %). This transformation is achieved using water as a green solvent and a 30 W white light as a visible light source, demonstrating the catalyst's potential for sustainable and environmentally benign reactions.

Structural engineering evoked multifunctionality in molybdate nanosheets for industrial oxygen evolution and dual energy storage devices inspired by multi-method calculations

Structural engineering, including electronic and geometric modulations, is a good approach to improve the activity of electrocatalysts. Herein, we employed FeOOH and the second metal center Ni to modulate the electronic structure of CoMoO4 and used a low temperature solvothermal route and a chemical etching method to prepare the special hollow hierarchical structure. Based on the prediction of multi-method calculations by density functional theory (DFT) and ab initial molecular dynamics (AIMD), a series of materials were fabricated. Among them, the optimal hollow FeOOH/(Ni1Co1)MoO4 by coating (NiCo)MoO4 nanosheets on FeOOH nanotubes showed excellent performances toward high current density oxygen evolution reaction (OER) in alkaline and simulated seawater solutions, hybrid supercapacitor (HSC), and aqueous battery due to the well-controlled electronic and geometric structures. The optimal FeOOH/(Ni1Co1)MoO4 required overpotentials of 225 and 546 mV to deliver 10 and 1000 mA cm-2 current densities toward alkaline OER, and maintained a good stability for 100 h at 200 mA cm-2 with negligible attenuation. The FeOOH/(Ni1Co1)MoO4//Pt/C electrolyzer exhibited a low cell voltage of 1.52 and 1.79 V to drive 10 and 200 mA cm-2 and retained a long-term durability nearly 100 h at 1.79 V. As the electrode of energy storage devices, it possessed a specific capacity of 342 mA h g-1 at 1 A g-1. HSC and SC-type battery devices were fabricated. The assembled HSC kept a capacitance retention of 94 % after 10,000 cycles. This work provided a way to fabricate effective and stable multifunctional materials for energy storage and conversion with the aid of multi-method calculations.

Photoredox coupling of carbon dioxide reduction with tetracycline oxidation using excited-state bismuth and cobalt dual sites over cobalt-tailored bismuth oxychloride

Photocatalytic carbon dioxide (CO2) conversion and simultaneous pollutant oxidation in a single system are promising approaches to mitigate energy and environmental challenges. However, the limited availability of active photocatalyst sites led to slow reaction kinetics and poor selectivity. Current research has predominantly focused on ground-state reactive sites of semiconductors, with less emphasis on active sites in their excited states. Therefore, gaining insights into the active sites in the excited state of semiconductors could provide a significant breakthrough in understanding the photocatalytic reaction mechanism. In this study, cobalt-doped bismuth oxychloride nanosheets containing abundant oxygen vacancies (OVs) were used as a model to investigate the active sites in excited states. These nanosheets were used to integrate CO2 reduction with tetracycline (TC) oxidation. Combining theoretical calculations with in situ characterizations revealed that under excited-state conditions photogenerated electrons transfer from cobalt (Co) dopants to OVs and subsequently to bismuth (Bi) atoms, forming Bi(3-x)+ sites enriched with excited electrons. These excited-electron-rich Bi(3-x)+ sites and electron-deficient Co sites contribute to CO2 reduction and TC oxidation, respectively. This study provides a comprehensive understanding of active sites in the excited state in doped semiconductors at the atomic level, reinforcing their potential for synergistic CO2 reduction and pollutant degradation.

Engineering single-atom rhodium-C3N sites on covalent organic frameworks for boosting photocatalytic hydrogen evolution

Developing efficient and stable photocatalysts for solar hydrogen (H2) energy conversion is meaningful but challenging. Herein, a novel photocatalyst with Rh single atoms (Rh SAs) anchoring in β-ketoimine-linked covalent organic frameworks (TpPa-1) via RhC3N sites is proposed for achieving highly efficient H2 production in phosphate buffer saline (PBS) solution with sodium ascorbate (SA) as sacrificial agent under visible light. TpPa-1 with abundant N and C-chelate sites provides a reliable basis for anchoring Rh single atoms. The optimized Rh SAs/TpPa-1 exhibits an outstanding hydrogen evolution activity (1836.81μmol h-1 g-1), 9.34 and 2.27 folds enhancement than that of pristine TpPa-1 and Rh NPs/TpPa-1. X-ray absorption fine structure (XAFS) combined with density functional theory (DFT) calculations reveal that the significant improvement in H2 evolution performance on Rh SAs/TpPa-1 originates from the unique RhC3N coordination environment, promoting the charge separation and migration at the atomic interface, and thus decreasing the energy barrier for H* formation. Notably, in situ Raman technique confirmed Rh SAs was the main active sites (RhH) for proton reduction.

Ultraviolet-Visible-near infrared induced photocatalytic H2 evolution over S-scheme Cu2-xSe/ZnSe heterojunction with surface plasma effects

Localized surface plasmon resonance (LSPR) effect plays a crucial role in the field of solar energy utilization. In this work, we successfully prepared a Cu2-xSe/ZnSe S-scheme heterojunction with a broad-spectrum response using the hot-injection and low-temperature water bath method. Importantly, we demonstrated that the photothermal effect induced by the LSPR of nonstoichiometric Cu2-xSe can significantly improve the slow kinetics of water splitting, resulting in an apparent activation energy reduction from 50.1 to 28.7 kJ·mol-1. This improvement is responsible for achieving the highest photocatalytic H2 evolution rate of 63.6 mmol·g-1·h-1 over 2.7 % Cu2-xSe/ZnSe under the wavelength ranged from 200 to 2500 nm, which is 3.4 and 5.6 times higher than that of ZnSe and Cu2-xSe, respectively. Furthermore, the composite exhibits a remarkable H2 production rate of 0.108 mmol·g-1·h-1 under near-infrared spectroscopy (800<λ<2500 nm), while ZnSe shows limited capability in H2 releasing. Additionally, Cu2-xSe/ZnSe demonstrates distinct photocurrent response when λ > 800 nm. The enhanced performance in H2 evolution can be attributed to the synergistic effect of LSPR-induced light absorption and S-scheme heterojunction, which not only expands the light absorption range to the near-infrared region but also facilitates hot electron injection, charge carrier separation and transfer, leading to a faster surface reaction kinetics. This study provides an effective approach for designing a broad-spectrum light responsive non-precious metal-based photothermal-assisted photocatalytic system.

Construction of dual driving force in carbon nitride for highly efficient hydrogen evolution: Simultaneously manipulating carriers transport in intra- and interlayer

Photocatalytic hydrogen evolution is widely recognized as an environmentally friendly approach to address future energy crises and environmental issues. However, rapid recombination of photo-induced charges over carbon nitride in lateral and vertical direction hinder this process. Herein, we proposed an effective strategy involving the embedding of benzene rings and the intercalation of platinum atoms on carbon nitride for a controlled intralayer and interlayer charges flow. Modified carbon nitride exhibits a significant higher hydrogen evolution rate (6288.5 μmol/g/h), which is 42 times greater than that of pristine carbon nitride. Both experiments and simulations collectively indicate that the improved photocatalytic activities can be attributed to the adjustment of the highly symmetric structure of carbon nitride, achieved by embedding benzene rings to induce the formation of an intralayer build-in electric field and intercalating Pt atoms to enhance interlayer polarization, which simultaneously accelerate lateral and vertical charges migration. This dual-direction charges separation mechanism in carbon nitride provides valuable insights for the development of highly active photocatalysis.

Activating peroxymonosulfate with MOF-derived NiO-NiCo2O4/titanium membrane for water treatment: A non-radical dominated oxidation mechanism

Traditional peroxymonosulfate (PMS) catalytic membranes dominated by radical pathways often face interference from complex components in water bodies. Herein, we employed a controlled electro-deposition technique to coat a Ni-Co metal-organic framework (MOF) precursor onto titanium hollow fiber membrane (THFM), followed by high-temperature calcination to synthesize a MOF-derived NiO-NiCo2O4/THFM (M-NNCO-THFM) PMS catalytic membrane. Then, the M-NNCO-THFM filtration integrated with PMS activation (MFPA process) for water treatment. Experimental results demonstrated that the M-NNCO-THFM MFPA process successfully achieved complete phenol (PE) removal via a non-radical-dominated degradation pathway, involving singlet oxygen (1O2) and electron transfer, while exhibiting wide pH adaptability and exceptional stability in complex water matrices. Mechanism analysis revealed that the electron transfer process was significantly enhanced by the MOF-derived heterojunction structure, which increased the flat-band potential from 0.39 eV to 0.56 eV, thereby facilitating efficient electron transfer for PE removal. The non-radical 1O2 pathway was primarily due to the cycling of metal valence states (Ni2+/Co3+), leading to the reduction of Co2+ and its reaction with PMS, resulting in the generation of reactive species. Furthermore, electrochemical measurements indicated that the M-NNCO-THFM exhibited lower charge transfer resistance and enhanced charge transfer efficiency compared to non-MOF-derived NNCO-THFM, corresponding to the superior catalytic performance and electrochemically active surface area of M-NNCO-THFM.

A fast and sensitive colorimetric sensor for residual chlorine detection made with oxidized cellulose

Residual chlorine from widespread disinfection processes forms byproducts in water that are harmful to humans and ecosystems. Portable sensors are essential tools for the on-site monitoring of residual chlorine in environmental samples. Here, an inexpensive colorimetric sensor was developed by grafting via amidation the chromogen orthotolidine (OTO) to the surface of a TEMPO-oxidized cellulose filter paper (O-TOFP). A thorough characterization of the sensor strip demonstrated that it was highly stable and that it could be stored for a long period before usage. O-TOFP had a fast response time of 30 s, was highly selective for residual chlorine ions (ClO-) with an accuracy of at least 95 %, and exhibited an excellent limit of detection of only 0.045 mg/L when combined with smartphone image acquisition. With its many positive features, the easy-to-use and robust O-TOFP sensor described here could become a useful tool for the determination of residual chlorine in different water samples.

Imbalanced and Unchecked: The Role of Metal Dyshomeostasis in Driving COPD Progression

Chronic obstructive pulmonary disease (COPD) is a chronic respiratory condition characterized by persistent inflammation and oxidative stress, which ultimately leads to progressive restriction of airflow. Extensive research findings have cogently suggested that the dysregulation of essential transition metal ions, notably iron, copper, and zinc, stands as a critical nexus in the perpetuation of inflammatory processes and oxidative damage within the lungs of COPD patients. Unraveling the intricate interplay between metal homeostasis, oxidative stress, and inflammatory signaling is of paramount importance in unraveling the intricacies of COPD pathogenesis. This comprehensive review aims to examine the current literature on the sources, regulation, and mechanisms by which metal dyshomeostasis contributes to COPD progression. We specifically focus on iron, copper, and zinc, given their well-characterized roles in orchestrating cytokine production, immune cell function, antioxidant depletion, and matrix remodeling. Despite the limited number of clinical trials investigating metal modulation in COPD, the advent of emerging methodologies tailored to monitor metal fluxes and gauge responses to chelation and supplementation hold great promise in unlocking the potential of metal-based interventions. We conclude that targeted restoration of metal homeostasis represents a promising frontier for ameliorating pathological processes driving COPD progression.

Site engineering of linear conjugated polymers to regulate oxygen adsorption affinity for boosting photocatalytic production of hydrogen peroxide without sacrificial agent

Artificial photosynthesis of hydrogen peroxide (H2O2) is a hopeful alternative to the industrial anthraquinone process. However, rational fabrication of the photocatalysts for the production of H2O2 without any sacrificial agents is still a formidable challenge. Herein, two kinds of linear conjugated polymers (LCPs) including pyridinic N functionalized polymer (DEB-N2) and pyridinic N non-contained polymer (DEB-N0) were successfully synthesized. DEB-N2 displays enhanced light capturing ability and good dispersion in water, leading to a substantial initial H2O2 generation rate of 3492μmol g-1h-1 as well as remarkable photocatalytic stability in pure water. Furthermore, the temperature programmed desorption (TPD) and density functional theory (DFT) analysis reveal that highly electronegative pyridine-N atoms in DEB-N2 boost the adsorption affinity of oxygen molecules, which facilitates the occurrence of the oxygen reduction reaction, therefore enhancing the performance of photocatalytic H2O2 production. This study unveils that the presence of pyridinic N in DEB-N2 has a significant impact on photocatalytic H2O2 production, suggesting the precise manipulation of the chemical structure of polymer photocatalysts is essential to achieve efficient solar-to-chemical energy conversion.

TiO2-based photocatalysts from type-II to S-scheme heterojunction and their applications

Photocatalysis is a promising sustainable technology to remove organic pollution and convert solar energy into chemical energy. Titanium dioxide has drawn extensive attention in this field owing to its high activity under UV light, good chemical stability, large availability, low price and low toxicity. However, the poor quantum efficiency derived from fast electron/hole recombination, the limited utilization of sunlight, and a weak reducing ability still hinder its practical application. Among the modification strategies of TiO2 to enhance its performance, the construction of heterojunctions with other semiconductors is a powerful and versatile way to maximise the separation of photogenerated charge carriers and steer their transport toward enhanced efficiency and selectivity. Here, the research progress and current status of TiO2 modification are reviewed, focusing on heterojunctions. A rapid evolution of the understanding of the different charge transfer mechanisms is witnessed from traditional type II to the recently conceptualised S-scheme. Particular attention is paid to different synthetic approaches and interface engineering methods designed to improve and control the interfacial charge transfer, and several cases of TiO2 heterostructures with metal oxides, metal sulfides and carbon nitride are discussed. The application hotspots of TiO2-based photocatalysts are summarized, including hydrogen generation by water splitting, solar fuel production by CO2 conversion, and the degradation of organic water pollutants. Hints about less studied and emerging processes are also provided. Finally, the main issues and challenges related to the sustainability and scalability of photocatalytic technologies in view of their commercialization are highlighted, outlining future directions of development.

Multi-walled carbon nanotubes-metal-organic framework nanocomposite based sensor for the monitoring of multiple monoamine neurotransmitters in living cells

The levels of monoamine neurotransmitters (MNTs) including dopamine (DA), adrenaline (Adr), norepinephrine (NE) and 5-hydroxytryptamine (5-HT) in cells are useful indicators to explore the pathogenesis of MNTs-related diseases such as Alzheimer's disease, Parkinson's disease and depression. Herein, we constructed a novel electrochemical sensing platform based on multi-walled carbon nanotubes (MWCNTs)-amine functionalized Zr (IV) metal-organic framework (UIO-66-NH2) nanocomposite for the detection of multiple MNTs including DA, Adr, NE and 5-HT. The synergistic effect between MWCNTs and UIO-66-NH2 endowed the nanocomposite with high specific surface area, low interface impedance and superior electrocatalytic activity, which effectively enhance the electrochemical performance of the sensor. The MWCNTs-UIO-66-NH2 nanocomposite-based sensor exhibited satisfied sensitivity for the quantitative measurement of DA, Adr, NE and 5-HT, as well as low detection limit. The outstanding biocompatibility of the constructed sensor permitted it to be successfully implemented for the real-time monitoring of DA released by PC12 and C6 cells, providing a promising strategy for clinical diagnosis of MNTs-related disorders and diseases.

Composites formed by layered double hydroxides with inorganic compounds: An overview of the synthesis methods and characteristics

Nowadays, layered double hydroxides (LDH), sometimes referred as hydrotalcite-like compounds, have gained great attention since their composition and structure can be easily modified, so that they can be implemented in multiple fields. LDH-based composite materials based on LDH exhibit tremendously improved properties such as high specific surface area, which promotes the accessibility to a greater number of LDH active sites, considerably improving their catalytic, adsorbent and biological activities. Therefore, this review summarizes and discusses the synthesis methods of composites constituted by LDH with other inorganic compounds such as zeolites, cationic clays, hydroxyapatites, among many others, and describe the resulting characteristics of the resulting composites, emphasizing the morphology. Brief descriptions of their properties and applications are also included.

Interface reconstruction of MXene-Ti3C2 doped CeO2 nanorods for remarked photocatalytic ammonia synthesis

Prospective photocatalytic ammonia synthesis process has received more attentions but quite challenging with the low visible light utilization and weak N2 molecule absorption ability around the photocatalysts. Herein, interface reconstruction of MXene-Ti3C2/CeO2 composites with high-concentration active sites through the carbon-doped process are presented firstly, and obvious transition zones with the three-phase reaction interface are formed in the as-prepared catalysts. The optimal co-doped sample demonstrates an excellent photo response in the visible light region, the strongest chemisorption activity and the most active sites. Moreover, much more in-situ extra oxygen defects are also produced under light irradiation. It is expected that the double decorated catalyst shows a remarked ammonia production rate of above 0.76 mmol gcal-1·h-1 under visible-light illumination and a higher apparent quantum efficiency of 1.08 % at 420 nm, which is one of the most completive properties for the photocatalytic N2 fixation at present.

Bioaccessibility of bioactive compounds from Pereskia aculeata and their cellular antioxidant effect

Ora-pro-nobis (Pereskia aculeata) is a Cactaceae plant with edible leaves and fruits whose extracts are consumed to promote health, albeit bioactive compounds' bioaccessibility was still not assessed. To address this, ora-pro-nobis fruits (FE) and leaf extracts (LE) were subjected to in vitro digestion to better understand how this process impacts the bioactivities of the extracts. The study investigated the composition of the extracts, their cytotoxicity, and their chemical, plasmatic, and cellular antioxidant capacity. The results revealed that total polyphenolics were about 70% bioaccessible in LE and FE, with phenylalanine being the most bioaccessible essential amino acid in leaves (42.7%) and fruits (83.6%). The samples' antioxidant activity (CUPRAC) was reduced by 25%. LE demonstrated antioxidant activity against human plasma oxidation and haemolysis (21.8%), but digestion mitigated these activities. FE diminished haemolysis (47.0%) and presented cytotoxicity (IC50 = 1086 μg/mL) to HUVEC cells, but these properties were lost following digestion. Ultimately, digestion partially degraded the samples' bioactive compounds, diminishing their cellular protection against oxidative stress.

Oxygen vacancy-mediated Mn2O3 catalyst with high efficiency and stability for toluene oxidation

Oxygen vacancy engineering in transition metal oxides is an effective strategy for improving catalytic performance. Herein, defect-enriched Mn2O3 catalysts were constructed by controlling the calcination temperature. The high content of oxygen vacancies and accompanying Mn4+ ions were generated in Mn2O3 catalysts calcined at low temperature, which could greatly improve the low-temperature reducibility and migration of surface oxygen species. DFT theoretical calculations further confirmed that molecular oxygen and toluene were easily adsorbed over defective α-Mn2O3 (222) facets with an energy of -0.29 and -0.48 eV, respectively, and corresponding OO bond length is stretched to 1.43 Å, resulting in the highly reactive oxygen species. Mn2O3-300 catalyst with abundant oxygen vacancies exhibited the highest specific reaction rate and lowest activation energy. Furthermore, the optimized catalyst possessed the outstanding stability, water tolerance and CO2 yield. In comparison with the fresh Mn2O3-300 catalyst, the physical structure and surface property of the used catalyst remained almost unchanged regardless of whether undergoing the stability test at consecutive catalytic runs as well as high temperature, and water resistance test. In situ DRIFTS spectra further elucidated that introducing the water vapor had little effect on the reaction intermediates, indicating the excellent durability of the defect-enriched catalyst.

Construction of a BiOI/ZnO heterojunction on biomass Juncus effusus fiber for photodegradation of organic pollutants

Semiconductor heterojunction engineering and three-dimensional (3D) architecture construction have been considered highly desirable strategies to enhance photocatalytic performance. Herein, a BiOI/ZnO composite photocatalyst with a 3D flower-like architecture was successfully prepared, which was stably immobilized on three-dimensional porous lignocellulosic biomass Juncus effusus (JE) fiber. The outstanding photocatalytic performance of the BiOI/ZnO-JE fiber was confirmed by the degradation of tetracycline hydrochloride (TC, 90%), ciprofloxacin (CIP, 79%), and norfloxacin (NOR, 81%). The enhanced photocatalytic activities were mainly attributed to the synergistic absorption performance of the lignocellulosic JE and the effective transfer and separation of charges. Moreover, the hydroxyl (·OH) and superoxide radicals (·O2-) are the main reactive species in the photocatalytic process according to the analysis. This work may provide a novel perspective for constructing high-performance lignocellulosic-based photocatalytic materials.

Multiscale calculations reveal new insights into the reaction mechanism between KRASG12C and α, β-unsaturated carbonyl of covalent inhibitors

Utilizing α,β-unsaturated carbonyl group as Michael acceptors to react with thiols represents a successful strategy for developing KRASG12C inhibitors. Despite this, the precise reaction mechanism between KRASG12C and covalent inhibitors remains a subject of debate, primarily due to the absence of an appropriate residue capable of deprotonating the cysteine thiol as a base. To uncover this reaction mechanism, we first discussed the chemical reaction mechanism in solvent conditions via density functional theory (DFT) calculation. Based on this, we then proposed and validated the enzymatic reaction mechanism by employing quantum mechanics/molecular mechanics (QM/MM) calculation. Our QM/MM analysis suggests that, in biological conditions, proton transfer and nucleophilic addition may proceed through a concerted process to form an enolate intermediate, bypassing the need for a base catalyst. This proposed mechanism differs from previous findings. Following the formation of the enolate intermediate, solvent-assisted tautomerization results in the final product. Our calculations indicate that solvent-assisted tautomerization is the rate-limiting step in the catalytic cycle under biological conditions. On the basis of this reaction mechanism, the calculated kinact/ki for two inhibitors is consistent well with the experimental results. Our findings provide new insights into the reaction mechanism between the cysteine of KRASG12C and the covalent inhibitors and may provide valuable information for designing effective covalent inhibitors targeting KRASG12C and other similar targets.

Microwave heating-assisted synthesis of ultrathin platinum-based trimetallic nanosheets as highly stable catalysts towards oxygen reduction reaction in acidic medium

There are currently almost no ternary platinum-based nanosheets used for acidic oxygen reduction reactions (ORR) due to the difficulty in synthesizing ternary nanosheets with high Pt content. In this work, several ultrathin platinum-palladium-copper nanosheets (PtPdCu NSs) with a thickness of around 1.90 nm were prepared via a microwave heating-assisted method. Microwave heating allows a large number of Pt atoms to deposit into PdCu nanosheets, forming Pt-based ternary nanosheets with high Pt content. Among them, Pt38Pd50Cu12 NSs catalyst displays the highest mass activity (MA) measured in 0.1 M HClO4 of 0.932 A/mgPt+Pd which is 8.6 times of that Pt/C. Besides, Pt38Pd50Cu12 NSs catalyst also exhibits excellent stability with an extremely low MA attenuation after 80,000 cycles accelerated durability testing (ADT) tests. In the single cell tests, the Pt38Pd50Cu12 NSs catalyst manifests higher maximum power density of 796 mW cm-2 than Pt/C of 606 mW cm-2. Density functional theory (DFT) calculations indicate the weaker adsorption between Pt and O-species in Pt38Pd50Cu12 NSs leads to a significant enhancement of ORR activity. This study provides a new strategy to design and prepare ultrathin Pt-based trimetallic nanosheets as efficient and durable ORR catalysts.

Bifunctional CdS-MoO2 catalysts for selective oxidation of lactic acid coupled with photocatalytic H2 production

The persistent hurdles of charge rapid recombination, inefficient use of light and utilization of sacrificial reagents have plagued the field of photocatalytic hydrogen evolution (PHE). In this research, tiny MoO2 nanoparticles of 10 nm in diameter were prepared through a straightforward solvothermal approach with a specific ratio of oleylamine and oleic acid as stabilizers. The critical factor in the synthesis process was found to be the ratio of oleylamine to oleic acid. Moreover, a two-phase interface assembly method facilitated the uniform deposition of MoO2 onto CdS nanorods. Due to the localized plasmonic-thermoelectric effect on the surface of MoO2 along with its abundant oxygen vacancies, the composite catalyst exhibited outstanding photo-utilization efficiency and an abundance of active sites. The CdS-MoO2 composite displayed a unique photochemical property in transforming lactic acid into pyruvic acid and generating hydrogen simultaneously. After exposure to artificial sunlight for 4 h, significant values of 4.7 and 3.7 mmol⋅g-1⋅h-1 were achieved for hydrogen production and pyruvic acid formation, respectively, exceeding CdS alone by 3.29 and 4.02-fold, while the selectivity of pyruvic acid was 95.68 %. Furthermore, the S-Scheme electron transport mechanism in the composites was elucidated using Electron Paramagnetic Resonance (EPR) spectroscopy, radical trapping experiments, energy band structure analysis, and the identification of critical intermediates in the process of selective oxidation. This work sheds light on the design and preparation of high-performance photocatalysts for biorefining coupled with efficient hydrogen evolution.

The generation of sulfate species on Ir-based catalysts for boosting NO reduction with CO under the coexistence of O2 and SO2 atmosphere

Generally, sulfur poisoning is considered to be one of the main factors contributing to the deactivation of selective catalytic reduction of NOx by CO (CO-SCR) catalysts, while the promotional effect of SO2 on NO reduction over Ir/SiO2 is observed which is an interesting scientific phenomenon. After the introduction of 20 ppm SO2, NOx conversion increased from ∼ 40 % to ∼ 90 % at 275 °C, and N2 selectivity increased from ∼ 80 % to 100 % at 200 ∼ 300 °C. Furthermore, the promoting effect could remain unchanged after 24 h of continuous reaction. However, the temperature point for achieving complete conversion of CO increased from 225 °C to 275 °C after the introduction of SO2. Experimental characterization and theoretical calculation jointly proved that the inhibition of CO oxidation by the generation of sulfate was the main reason for promoting NO reduction. Under the coexistence of O2 and SO2, SO2 was firstly oxidized to SO3 on the iridium surface and generated sulfate species on surface hydroxyl groups of SiO2. Some active sites for O2 adsorption were covered by the generated surface sulfate, and adsorbed CO was hard to react with adsorbed O2, resulting in Langmuir-Hinshelwood (L-H) reaction pathways for CO oxidation being inhibited. Therefore, unoxidized CO reacted with NO adsorbed species and generated N2O to generate N2 and CO2, improving NO reduction. This new insight has implications for understanding the promotional effect of SO2 on NO reduction with CO in the presence of O2.

Facile fabrication of shape-controllable and reusable nanoporous catalytic aerogels based on Co-MOF and agarose for efficient decomposition of organic pollutants in water

Sulfate radical (SO4•-)-based advanced oxidation processes (SR-AOPs) have been studied to date by utilizing metal-organic frameworks as efficient catalysts to generate sulfate radicals by peroxymonosulfate (PMS) activation in water purification. It is important to select high-performance and reliable catalysts for efficient water remediation, and separation and recovery of catalysts are essential in the practical application of MOFs. Herein, we adapted thermally curable, shape-controllable, and cost-effective agarose (AG) as a smart matrix and ZIF-67, as a powerful catalyst to prepare nanoarchitectured aerogel (Z67@AG). This nanoporous aerogel composite can efficiently generate sulfate radicals and hydroxyl radicals by activating PMS in the nanopores. Z67@AG aerogel could be easily fabricated in various molds to make desired shapes. This approach enables its utilization for different filtering systems and demonstrates cost-effective and stable performance by mass production and reusability. In the SR-AOP, aerogel exhibited excellent catalytic decomposition performances of 95 % and 88 % efficiencies within 8 and 10 min for dye and levofloxacin, respectively. It is believed that the proposed highly catalytic nanoporous aerogel nanocomposite having cost-effectiveness, excellent catalytic activity, facile fabrication of desired shapes, and an excellent porous structure can be extended to the synthesis of various nanocomposites and emerging applications.

Shielding against erosion: Exploring the effectiveness of pre-erosion surface corrosion inhibitors

This study investigates the corrosion inhibition effect and adsorption process of two imidazoline corrosion inhibitors, HEIE and TDEI, on pre-eroded X65 steel surfaces. Analysis of weight loss and electrochemical measurements suggests that the irregular structure of pre-eroded surfaces may impede the uniform adsorption of corrosion inhibitors, resulting in reduced effectiveness pre-erosion. Particularly, at a 30° angle of pre-erosion, corrosion inhibition efficacy is observed to be at its lowest. The corrosion inhibition rates of HEIE and TDEI on X65 steel surfaces are found to be 11.9 % lower under pre-eroded conditions at a 30° angle compared to non-eroded surfaces at the same angle. Molecular dynamics (MD) simulations support these findings, indicating that TDEI exhibits lower energy bandgap values and more negative adsorption energies (Eads) compared to HEIE, aligning with experimental results. Moreover, TDEI demonstrates a smaller diffusion coefficient for corrosive agents than HEIE, suggesting stronger adsorption efficiency and a more pronounced protective effect. Study of the corrosion inhibition effect on pre-eroded surfaces provides new ideas and methods for improving protective measures.

Lamellar Ti3C2 MXene composite decorated with platinum-doped MoS2 nanosheets as electrochemical sensing functional platform for highly sensitive analysis of organophosphorus pesticides

Precisely detecting organophosphorus pesticides (OPs) is paramount in upholding human safety and environmental preservation, especially in food safety. Herein, an electrochemical acetylcholinesterase (AChE) sensing platform entrapped in chitosan (Chit) on the glassy carbon electrodes (GCEs) decorated with Pt/MoS2/Ti3C2 MXene (Pt/MoS2/TM) was constructed for the detection of chlorpyrifos. It is worth noting that Pt/MoS2/TM possesses good biocompatibility, remarkable electrical conductivity, environmental stability and large specific surface area. Besides, the heterostructure formed by the composite of TM and MoS2 improves the conductivity and maintains the original structure, which is conducive to improving the electrochemical property. The coordination effect between the individual components enables the even distribution of functional components and enhances the electrochemical performance of the biosensor (AChE-Chit/Pt/MoS2/TM). Under optimal efficiency and sensitivity, the AChE-Chit/Pt/MoS2/TM/GCE sensing platform exerts comparable analytical performance and a wide concentration range of chlorpyrifos from 10-12 to 10-6 M as well as a low limit of detection (4.71 × 10-13 M). Furthermore, the biosensor is utilized to detect OPs concerning three kinds of fruits and vegetables with good feasibility and recoveries (94.81% to 104.0%). This work would provide a new scheme to develop high-sensitivity sensors based on the two-dimensional nanosheet/laminar hybrid structure for practical applications in environmental monitoring and agricultural product detection.

Recovery technology of spent hydrogenation catalysts -A review

Spent hydrogenation catalysts (HDCs) contain many Mo, V, Co, Ni, and Al2O3 carriers, which are valuable secondary resources. However, improper disposal can also lead to environmental pollution risks. In the past decade, research reviews on the recovery of valuable metals from spent HDCs have been somewhat reported, mainly summarizing basic technical processes. Based on previous work, this article reviews the emerging recycling technologies of spent HDCs in recent years. The research trend of furnace optimization in the pyrometallurgical process was innovatively proposed, and the importance of developing new mild leaching agents for the high-quality recycling of Al2O3 carriers in the hydrometallurgical process was clarified.

Biobased heterogeneous renewable catalysts: Production technologies, innovations, biodiesel applications and circular bioeconomy

The growing population and waste biomass accumulation are leading to increased environmental pollution and climate change. Waste biomass comprising of nutrient rich components has promising potential to produce value-added products for sustainable environmental solutions. This review explores the critical role of bio-based heterogeneous catalysts in enabling sustainable waste biomass utilization. In industrial chemical transformations, over 95% involve catalysts, with more than 90% being heterogeneous systems, prized for their robustness, ease of product separation, and reusability. Bio-based heterogeneous catalysts address the pressing need for sustainable waste biomass management, allowing the conversion of diverse waste biomasses into biodiesel as valuable products. Research on these catalysts, particularly for biodiesel production, has shown yields exceeding 90% with enhanced catalyst reusability. This surge in research is evident from the increasing number of published articles, notably in 2022 and 2023, highlighting growing interest and importance in the scientific community. The synthesis of these catalysts is examined, including novel approaches and techniques to enhance their efficiency, selectivity, and stability. The challenges with their feasible solutions of heterogeneous catalysts in catalyst-based processes are addressed. Altogether, this review underscores the immense potential of bio-based heterogeneous catalysts in sustainable waste biomass utilization, aligning with resource efficiency and environmental conservation goals while offering distinct insights and perspectives on the latest innovations in the field.

Preparation of functionalized porous chitin carbon to enhance the H2O2 production and Fe3+ reduction properties of Electro-Fenton cathodes for efficient degradation of RhB

The performance of Electro-Fenton (EF) cathode materials is primarily assessed by H2O2 yield and Fe3+ reduction efficiency. This study explores the impact of pore structure in chitin-based porous carbon on EF cathode effectiveness. We fabricated mesoporous carbon (CPC-700-2) and microporous carbon (ZPC-700-3) using template and activation methods, retaining nitrogen from the precursors. CPC-700-2, with mesopores (3-5 nm), enhanced O2 diffusion and oxygen reduction, producing up to 778 mg/L of H2O2 in 90 min. ZPC-700-3, with a specific surface area of 1059.83 m2/g, facilitated electron transport and ion diffusion, achieving a Fe2+/Fe3+ conversion rate of 79.9%. EF systems employing CPC-700-2 or ZPC-700-3 as the cathode exhibited superior degradation performance, achieving 99% degradation of Rhodamine B, efficient degradation, and noticeable decolorization. This study provides a reference for the preparation of functionalized carbon cathode materials for efficient H2O2 production and effective Fe3+ reduction in EF systems.

Rational design and construction of direct Z-scheme ternary heterojunction photocatalyst AgBr/CoWO4/Ag for efficient environmental remediation

The indiscriminate discharge of micropollutants (e.g., dyes, antibiotics, industrial additives, etc.) represents a significant risk to human health, and the removal of these substances from water bodies has become a prominent area of research within the field of environmental remediation. A simple hydrothermal-precipitation-photoreduction method was employed to synthesize novel Z-scheme heterojunction photocatalysts of AgBr/CoWO4/Ag. The catalysts demonstrated remarkable degradation capabilities with regard to a range of micropollutants present in wastewater. Of the catalysts tested, 5AgBr/CoWO4/Ag exhibited the highest degradation rates, reaching 98.58% for Rhodamine B, 86.82% for tetracycline hydrochloride, and 95.60% for 2-mercaptobenzothiazole within 60 min. In particular, the reaction kinetic rate of 5AgBr/CoWO4/Ag towards Rhodamine B degradation (k2 = 0.26278 L mg-1·min-1) is 9 times that of AgBr (k2 = 0.02953 L mg-1·min-1) and 113 times that of CoWO4 (k2 = 0.00233 L mg-1·min-1), which serves to highlight the exceptional photocatalytic activity of the material. The experimental data and subsequent analysis indicated that the enhanced photocatalytic performance can be attributed to two factors: firstly, the electron mediation by Ag nanoparticles leading to improved charge separation efficiency, and secondly, the formation of Z-scheme heterojunctions between AgBr and CoWO4. The cyclic tests provided confirmation of the excellent stability and recyclability of the AgBr/CoWO4/Ag photocatalysts. It is anticipated that this study will facilitate the development of novel methods for the degradation of refractory micropollutants and provide insights into environmental remediation, thereby contributing to the sustainable development of society.

Visible-light-sensitive microrobots using H2O as fuel for highly efficient capture and precise detection of nanoplastics

Nanoplastics, which are small plastic particles resulting from the decomposition of plastic waste, can accumulate and adsorb toxic chemicals in aquatic environments, leading to detrimental effects on the environment and human health. Consequently, there is an urgent demand for the development of an efficient method to accurately quantify and effectively remove nanoplastics. Here, we prepared a novel "cage-like" microrobot for effective dynamic capture and highly sensitive surface-enhanced Raman scattering detection of nanoplastics in situ. The microrobot utilizes water as fuel under visible light and achieves efficient capture of nanoplastics within 2 min on the basis of the stacking structure between layers and electrostatic action. The microrobot could be recovered by an external magnetic field, and the SERS activity was greatly enhanced through the coupling of multilayer hot spots, with a detection limit of 1.27 μg/mL. We built a simple device to demonstrate the feasibility of the microrobot strategy of capturing plastic in real wastewater and further extended this technology to single-use plastic cups in everyday life. Moreover, many different types of plastic spectra can also be quickly distinguished when combined with machine learning. This work provides new ideas for improving the dynamic capture and effective monitoring of nanoplastics.