Eco-Compatible Solvent-Processed Organic Photovoltaic Cells with Over 16% Efficiency

Green-Solvent-Processable Organic Photovoltaics with High Performances Enabled by Asymmetric Non-Fullerene Acceptors

In this work, two asymmetric non-fullerene acceptors (NFAs), BTP-EHBO-4F and BTP-PHD-4F, are designed to be applied in green-solvent-processable organic photovoltaics (OPVs). BTP-EHBO-4F and BTP-PHD-4F show good solubilities in green solvent o-xylene. As a result, PM6:BTP-EHBO-4F-based devices exhibit outstanding photovoltaic performances using o-xylene as a solvent. By comparison, due to the poor solubility of Y6 in o-xylene, PM6:Y6-based devices show poor performances. Owing to the favorable phase separation, molecule packing, and orientation observed from atomic force microscopy (AFM) and grazing-incidence wide-angle X-ray scattering (GIWAXS) measurements, PM6:BTP-PHD-4F-based devices demonstrate a PCE of 15.91% with a V_OC of 0.87 V, a J_SC of 25.64 mA/cm², and an FF of 71.34%. Moreover, PM6:BTP-EHBO-4F-based devices exhibit an impressive PCE of 16.82% with a V_OC of 0.85 V, a J_SC of 26.12 mA/cm², and an FF of 75.78%, which is outstanding for OPVs using o-xylene as a solvent.

Elucidating Charge Generation in Green-Solvent Processed Organic Solar Cells

Organic solar cells have the potential to become the cheapest form of electricity. Rapid increase in the power conversion efficiency of organic solar cells (OSCs) has been achieved with the development of non-fullerene small-molecule acceptors. Next generation photovoltaics based upon environmentally benign “green solvent” processing of organic semiconductors promise a step-change in the adaptability and versatility of solar technologies and promote sustainable development. However, high-performing OSCs are still processed by halogenated (non-environmentally friendly) solvents, so hindering their large-scale manufacture. In this perspective, we discuss the recent progress in developing highly efficient OSCs processed from eco-compatible solvents, and highlight research challenges that should be addressed for the future development of high power conversion efficiencies devices.

Controlling solid-state structure and film morphology in non-fullerene organic photovoltaic devices

Organic solar cells (OSCs) have long promised to provide renewable energy in a scalable, cost-effective way; however, for years, their relatively low efficiency has been a significant barrier to commercialization. Recent progress on cell efficiency means that OSCs are now much more competitive with other established technologies. These key advancements have come from better understanding and controlling the molecular structure, solid-state packing, and film morphology of the light absorbing layer. This focused review will explore the different ways that the solid-state structure and film morphology of the light absorbing layer can be controlled. It will examine the key features of an efficient light absorbing layer and present guiding principles for creating efficient OSCs. The future directions and remaining research questions of this field will be briefly discussed.

Recent advances in non-fullerene organic photovoltaics enabled by green solvent processing

Solution-processed organic photovoltaic (OPV) as a new energy device has attracted much attention due to its huge potential in future commercial manufacturing. However, so far, most of the studies on high-performance OPV have been treated with halogenated solvents. Halogenated solvents not only pollute the environment, but are also harmful to human health, which will negatively affect the large-scale production of OPV in the future. Therefore, it is urgent to develop low-toxic or non-toxic non-halogen solvent-processable OPV. Compared with conventional fullerene OPVs, non-fullerene OPVs exist with stronger absorption, better-matched energy levels and lower energy loss. Processing photoactive layers with non-fullerenes as the acceptor material has broad potential advantages in non-halogenated solvents. This review introduces the research progress of non-fullerene OPV treated by three different kinds of green solvents as the non-halogenated and aromatic solvent, the non-halogenated and non-aromatic solvent, alcohol and water. Furthermore, the effects of different optimization strategies on the photoelectric performance and stability of non-fullerene OPV are analyzed in detail. The current optimization strategy can increase the power conversion efficiency of non-fullerene OPV processed with non-halogen solvents up to 17.33%, which is close to the performance of processing with halogen-containing solvents. Finally, the commercial potential of non-halogen solvent processing OPVs is discussed. The green solvent processing of non-fullerene-based OPVs will become a key development direction for the future of the OPV industry.

Recent Progress in the Design of Fused-Ring Non-Fullerene Acceptors-Relations between Molecular Structure and Optical, Electronic, and Photovoltaic Properties

Organic solar cells are on the dawn of the next era. The change of focus toward non-fullerene acceptors has introduced an enormous amount of organic n-type materials and has drastically increased the power conversion efficiencies of organic photovoltaics, now exceeding 18%, a value that was believed to be unreachable some years ago. In this Review, we summarize the recent progress in the design of ladder-type fused-ring non-fullerene acceptors in the years 2018-2020. We thereby concentrate on single layer heterojunction solar cells and omit tandem architectures as well as ternary solar cells. By analyzing more than 700 structures, we highlight the basic design principles and their influence on the optical and electrical structure of the acceptor molecules and review their photovoltaic performance obtained so far. This Review should give an extensive overview of the plenitude of acceptor motifs but will also help to understand which structures and strategies are beneficial for designing materials for highly efficient non-fullerene organic solar cells.

Designs and understanding of small molecule-based non-fullerene acceptors for realizing commercially viable organic photovoltaics

Organic photovoltaics (OPVs) have emerged as a promising next-generation technology with great potential for portable, wearable, and transparent photovoltaic applications. Over the past few decades, remarkable advances have been made in non-fullerene acceptor (NFA)-based OPVs, with their power conversion efficiency exceeding 18%, which is close to the requirements for commercial realization. Novel molecular NFA designs have emerged and evolved in the progress of understanding the physical features of NFA-based OPVs in relation to their high performance, while there is room for further improvement. In this review, the molecular design of representative NFAs is described, and their blend characteristics are assessed via statistical comparisons. Meanwhile, the current understanding of photocurrent generation is reviewed along with the significant physical features observed in high-performance NFA-based OPVs, while the challenging issues and the strategic perspectives for the commercialization of OPV technology are also discussed.

A Tandem Organic Photovoltaic Cell with 19.6% Efficiency Enabled by Light Distribution Control

Despite more potential in realizing higher photovoltaic performance, the highest power conversion efficiency (PCE) of tandem organic photovoltaic (OPV) cells still lags behind that of state-of-the-art single-junction cells. In this work, highly efficient double-junction tandem OPV cells are fabricated by optimizing the photoactive layers with low voltage losses and developing an effective method to tune optical field distribution. The tandem OPV cells studied are structured as indium tin oxide (ITO)/ZnO/bottom photoactive layer/interconnecting layer (ICL)/top photoactive layer/MoO_x /Ag, where the bottom and top photoactive layers are based on blends of PBDB-TF:ITCC and PBDB-TF:BTP-eC11, respectively, and ICL refers to interconnecting layer structured as MoO_x /Ag/ZnO:PFN-Br. As these results indicate that there is not much room for optimizing the bottom photoactive layer, more effort is put into fine-tuning the top photoactive layer. By rationally modulating the composition and thickness of PBDB-TF:BTP-eC11 blend films, the 300 nm-thick PBDB-TF:BTP-eC11 film with 1:2 D/A ratio is found to be an ideal photoactive layer for the top sub-cell in terms of photovoltaic characteristics and light distribution control. For the optimized tandem cell, a PCE of 19.64% is realized, which is the highest result in the OPV field and certified as 19.50% by the National Institute of Metrology.

Tuning of the Interconnecting Layer for Monolithic Perovskite/Organic Tandem Solar Cells with Record Efficiency Exceeding 21

The photovoltaic performance of inorganic perovskite solar cells (PSCs) still lags behind the organic-inorganic hybrid PSCs due to limited light absorption of wide bandgap CsPbI_3-xBr_x under solar illumination. Constructing tandem devices with organic solar cells can effectively extend light absorption toward the long-wavelength region and reduce radiative photovoltage loss. Herein, we utilize wide-bandgap CsPbI₂Br semiconductor and narrow-bandgap PM6:Y6-BO blend to fabricate perovskite/organic tandem solar cells with an efficiency of 21.1% and a very small tandem open-circuit voltage loss of 0.06 V. We demonstrate that the hole transport material of the interconnecting layers plays a critical role in determining efficiency, with polyTPD being superior to PBDB-T-Si and D18 due to its low parasitic absorption, sufficient hole mobility and quasi-Ohmic contact to suppress charge accumulation and voltage loss within the tandem device. These perovskite/organic tandem devices also display superior storage, thermal and ultraviolet stabilities.

Synergistic Effects of Chlorination and Branched Alkyl Side Chain on the Photovoltaic Properties of Simple Non-Fullerene Acceptors with Quinoxaline as the Core

To date, the fused-ring electron acceptors show the best photovoltaic performances, and the development of simple non-fullerene acceptors via intramolecular noncovalent interactions can reduce synthetic costs. In this work, four simple non-fullerene acceptors with an A-D-A'-D-A configuration (QCIC1, QCIC2, QCIC3, and QCIC4) were synthesized. They contained the same conjugated backbone (A': quinoxaline; D: cyclopentadithiophene; A: dicyano-indanone) but different halogen atoms and alkyl side chains. Due to the chlorination on the end-groups and the most and/or longest branched alkyl side chains on the backbone, the blended film composed of QCIC3 and donor poly{[2,6'-4,8-di(5-ethylhexylthienyl)benzo [1,2-b : 4,5-b']dithiophene]-alt-[5,5-(1',3'-di-2-thienyl-5',7'-bis(2-ethylhexyl)benzo[1',2'-c : 4',5'-c']dithiophene-4,8-dione)]} (PBDB-T) exhibited the strongest π-π stacking and the most suitable phase-separation domains among the four blended films. Therefore, the QCIC3-based organic solar cells yielded the highest power conversion efficiency of 10.55 %. This work provides a pathway to optimize the molecular arrangements and enhance the photovoltaic property of simple electron acceptors through subtle chemical modifications.

Indoor Organic Photovoltaics for Self-Sustaining IoT Devices: Progress, Challenges and Practicalization

Indoor photovoltaics (IPVs) have great potential to provide a self-sustaining power source for Internet-of-Things (IoT) devices. The rapid growth in demand for low-power IoT devices for indoor application not only boosts the development of high-performance IPVs, but also promotes the electronics and semiconductor industry for the design and development of ultra-low-power IoT systems. In this Review, the recent progress in IPV technologies, design rules, market trends, and future prospects for highly efficient indoor photovoltaics are discussed. Special attention is given to the progress and development of organic photovoltaics (OPVs), which demonstrate great possibilities for IPVs, owing to their bandgap tunability, high absorbance coefficient, semitransparency, solution processability, and easy large-area manufacturing on flexible substrates. Highly efficient indoor organic photovoltaics (IOPVs) can be realized through designing efficient donor and acceptor absorber materials that have good spectral responses in the visible region and better energy-aligned interfacial layers, and through modulation of optical properties. Interfacial engineering, photovoltage losses, device stability, and large-area organic photovoltaic modules are surveyed to understand the mechanisms of efficient power conversion and challenges for IOPVs under indoor conditions as a self-sustaining power source for IoT devices. Finally, the prospects for further improve in IOPV device performance and practical aspects of integrating IOPVs in low-power IoT devices are discussed.

17.6%-Efficient Quasiplanar Heterojunction Organic Solar Cells from a Chlorinated 3D Network Acceptor

Bulk heterojunction (BHJ) organic solar cells (OSCs) have achieved great success because they overcome the shortcomings of short exciton diffusion distances. With the progress in material innovation and device technology, the efficiency of BHJ devices is continually being improved. For some special photovoltaic material systems, it is difficult to manipulate the miscibility and morphology of blend films, and this results in moderate, even poor device performance. Quasiplanar heterojunction (Q-PHJ) OSCs have been proposed to exploit the excellent photovoltaic properties of these materials. An OSC with BTIC-BO-4Cl has a 3D interpenetrating network structure with multiple channels that can facilitate the exciton diffusion and charge transport, and BTIC-BO-4Cl is therefore a good candidate for Q-PHJ OSCs. In this work, a D18:BTIC-BO-4Cl-based Q-PHJ device is fabricated. The exciton diffusion lengths of D18 and BTIC-BO-4Cl are in accord with the requirements of the Q-PHJ device and the efficiency of Q-PHJ device is as high as 17.60%. This study indicates that the Q-PHJ architecture can replace the BHJ architecture to produce excellent OSCs for certain unique donors and acceptors, providing an alternative approach to photovoltaic material design and device fabrication.

Simultaneously Enhanced Efficiency and Operational Stability of Nonfullerene Organic Solar Cells via Solid-Additive-Mediated Aggregation Control

The additive strategy is widely used in optimizing the morphology of organic solar cells (OSCs). The majority of additives are liquid with high boiling points, which will be trapped within device and consequently deteriorate performance during operation. In this work, solid but volatile additives 2-(4-fluorobenzylidene)-1H-indene-1,3(2H)-dione (INB-F) and 2-(4-chlorobenzylidene)-1H-indene-1,3(2H)-dione (INB-Cl) are designed to replace the common 1,8-diiodooctane (DIO) in nonfullerene OSCs. These additives present during solution casting but evaporate after moderate heating. Molecular dynamics simulations show that they can reduce the adsorption energy to improve π-π stacking among nonfullerene acceptor (NFA) molecules, an effect that enhances light absorption and electron mobility. Both INB-F and INB-Cl enhance efficiency, with INB-F achieving a maximum efficiency of 16.7% from 15.1% of the reference PBDB-T-2F (PM6):BTP-BO-4F (Y6-BO) cell, and outperforming DIO. Remarkably, they can simultaneously enhance the operational stability, with the INB-F-treated OSC maintaining over 60% of the initial efficiency after 1000 h operation, demonstrating a T₈₀ lifetime of 523 h, which is a significant improvement over T₈₀ values of 66.2 h for the reference and 6.6 h for DIO-treated OSC. The simultaneously enhanced efficiency and operational lifetime are also effective in PM6:BTP-BO-4Cl (Y7-BO) OSCs, demonstrating a universal strategy to improve the performance of OSCs.

Replacing the cyano (-C[triple bond, length as m-dash]N) group to design environmentally friendly fused-ring electron acceptors

The cyano-group (-C[triple bond, length as m-dash]N) is an electron-withdrawing group, which has been widely used to construct high-performance fused-ring electron acceptors (FREAs). Benefiting from these FREAs, the power conversion efficiency of organic solar cells has recently exceeded 18%. However, malononitrile is a highly toxic substance used to introduce -C[triple bond, length as m-dash]N during the synthesis of these FREAs. Therefore, the synthesis processes of most high-performance FREAs are typically harmful to the environment. Our previous work demonstrated that the electron-withdrawing ability of -C[triple bond, length as m-dash]N is necessary for FREAs. Thus, the use of other electron-withdrawing groups instead of -C[triple bond, length as m-dash]N to design environmentally friendly FREAs is feasible. We utilized seven electron-withdrawing groups, namely, -C[double bond, length as m-dash]NH, -N[double bond, length as m-dash]O, -CH[double bond, length as m-dash]O, -CO-CH3, -CO-OH, -CO-Cl, and -CO-Br, to replace -C[triple bond, length as m-dash]N in the commonly used acceptor Y6 to design new FREAs (Y6-CNH, Y6-NO, Y6-CHO, Y6-COCH3, Y6-COOH, Y6-COCl, and Y6-COBr). Multi-scale theoretical calculation methods were used to investigate the photoelectronic properties of these new FREAs, including energy level, absorption spectrum, exciton binding energy, and electron mobility. The results showed that Y6-CNH, Y6-COCH3 and Y6-COOH are unsuitable for use as acceptor materials because of their high frontier molecular orbital energy level and weak electron affinity. The strong absorption intensity and weak exciton binding energy of Y6-CHO, Y6-COCl, and Y6-COBr indicated that they can absorb more solar energy than Y6 and excitons are easier to separate into free charges. The electron mobility of Y6-CHO (3.53 × 10^-4 cm² V^-1 s^-1) was found to be approximately 28 times that of Y6-COCl (1.24 × 10^-5 cm² V^-1 s^-1) and Y6-COBr (1.28 × 10^-5 cm² V^-1 s^-1). The possible synthetic routes to Y6-CHO are environmentally friendly. Therefore, -CH[double bond, length as m-dash]O is the most suitable electron-withdrawing group for constructing high-performance environmentally friendly FREAs. This work can provide a new molecular design perspective in experimental science for developing high-performance environmentally friendly FREAs.

Extinction Coefficient Modulation of MoO3 Films Doped with Plasmonic Nanoparticles: From an Effective Medium Theory Description

This work focused on the application of the effective medium theory to describe the extinction coefficient (Qext) in molybdenum trioxide (MoO3) doped with different kinds of plasmonic nanoparticles, such as silver (Ag), gold (Au), and copper (Cu). Usually, in studies of these materials, it is normal to analyze the transmission or absorption spectra. However, the effect of this type or size of nanoparticles on the spectra is not as remarkable as the effect that is found by analyzing the Qext of MoO3. It was shown that the β-phase of MoO3 enhanced the intensity response of the Qext when compared to the α-phase of MoO3. With a nanoparticle size of 5 nm, the Ag-doped MoO3 was the configuration that presents the best response in Qext. On the other hand, Cu nanoparticles with a radius of 20 nm embedded in MoO3 was the configuration that presented intensities in Qext similar to the cases of Au and Ag nanoparticles. Therefore, implementing the effective medium theory can serve as a guide for experimental researchers for the application of these materials as an absorbing layer in photovoltaic cells.

Benzobis(Thiazole)-Based Conjugated Polymer with Varying Alkylthio Side-Chain Positions for Efficient Fullerene-Free Organic Solar Cells

Alkylthio groups can be used to modulate energy levels and molecular packing of organic semiconductors, which makes it important in the design of materials for organic solar cell. However, its effect has not been sufficiently exploited as most of the studies report introducing an alkylthio group to the donor unit and seldom to the acceptor unit of donor-acceptor conjugated polymers. In this report, two alkylthio-substituted polymers, namely, PBB-TSA and PBB-TSD, with benzo[1,2-d:4,5-d']bis(thiazole) (BBT) as the acceptor unit and benzo[1,2-b:4,5-b']dithiophene (BDT) as the donor unit, were rationally designed, synthesized, and applied in organic photovoltaics. An alkylthio side chain was substituted on the BBT-accepting unit for PBB-TSA, while for PBB-TSD, the alkylthio side chain was substituted on the BDT donor unit. PBB-TSA and PBB-TSD show upshifted and downshifted energy levels, respectively, compared to the nonsulfur-substituted material. Both polymers exhibit dominate face-on orientation, while PBB-TSD exhibits higher crystallinity compared to PBB-TSA. With the contribution of lower energy level and beneficial film morphology, the device based on PBB-TSD/IT-4F has much higher power conversion efficiency (PCE) of 14.6%, whereas the PBB-TSA blend had a lower PCE of 10.7%. 1,8-Diiodooctane can effectively optimize the blend film morphology, and the effect on device performance has also been demonstrated in detail. This result indicates that introducing an alkylthio side chain into the donor or acceptor moieties would result in materials with different energy levels and thus would be utilized to match with various acceptors, achieving optimized performance in organic solar cells.

Approaching 18% efficiency of ternary organic photovoltaics with wide bandgap polymer donor and well compatible Y6 : Y6-1O as acceptor

A series of ternary organic photovoltaics (OPVs) are fabricated with one wide bandgap polymer D18-Cl as donor, and well compatible Y6 and Y6-1O as acceptor. The open-circuit-voltage (VOC ) of ternary OPVs is monotonously increased along with the incorporation of Y6-1O, indicating that the alloy state should be formed between Y6 and Y6-1O due to their excellent compatibility. The energy loss can be minimized by incorporating Y6-1O, leading to the VOC improvement of ternary OPVs. By finely adjusting the Y6-1O content, a power conversion efficiency of 17.91% is achieved in the optimal ternary OPVs with 30 wt% Y6-1O in acceptors, resulting from synchronously improved short-circuit-current density (JSC ) of 25.87 mA cm-2, fill factor (FF) of 76.92% and VOC of 0.900 V in comparison with those of D18-Cl : Y6 binary OPVs. The JSC and FF improvement of ternary OPVs should be ascribed to comprehensively optimal photon harvesting, exciton dissociation and charge transport in ternary active layers. The more efficient charge separation and transport process in ternary active layers can be confirmed by the magneto-photocurrent and impedance spectroscopy experimental results, respectively. This work provides new insight into constructing highly efficient ternary OPVs with well compatible Y6 and its derivative as acceptor.

Unveiling structure-performance relationships from multi-scales in non-fullerene organic photovoltaics

Unveiling the correlations among molecular structures, morphological characteristics, macroscopic properties and device performances is crucial for developing better photovoltaic materials and achieving higher efficiencies. To achieve this goal, a comprehensive study is performed based on four state-of-the-art non-fullerene acceptors (NFAs), which allows to systematically examine the above-mentioned correlations from different scales. It's found that extending conjugation of NFA shows positive effects on charge separation promotion and non-radiative loss reduction, while asymmetric terminals can maximize benefits from both terminals. Another molecular optimization is from alkyl chain tuning. The shortened alkyl side chain results in strengthened terminal packing and decreased π-π distance, which contribute high carrier mobility and finally the high charge collection efficiency. With the most-acquired benefits from molecular structure and macroscopic factors, PM6:BTP-S9-based organic photovoltaics (OPVs) exhibit the optimal efficiency of 17.56% (certified: 17.4%) with a high fill factor of 78.44%, representing the best among asymmetric acceptor based OPVs. This work provides insight into the structure-performance relationships, and paves the way toward high-performance OPVs via molecular design.

A Synergistic Strategy of Manipulating the Number of Selenophene Units and Dissymmetric Central Core of Small Molecular Acceptors Enables Polymer Solar Cells with 17.5 % Efficiency

A dissymmetric backbone and selenophene substitution on the central core was used for the synthesis of symmetric or dissymmetric A-DA'D-A type non-fullerene small molecular acceptors (NF-SMAs) with different numbers of selenophene. From S-YSS-Cl to A-WSSe-Cl and to S-WSeSe-Cl, a gradually red-shifted absorption and a gradually larger electron mobility and crystallinity in neat thin film was observed. A-WSSe-Cl and S-WSeSe-Cl exhibit stronger and tighter intermolecular π-π stacking interactions, extra S⋅⋅⋅N non-covalent intermolecular interactions from central benzothiadiazole, better ordered 3D interpenetrating charge-transfer networks in comparison with thiophene-based S-YSS-Cl. The dissymmetric A-WSSe-Cl-based device has a PCE of 17.51 %, which is the highest value for selenophene-based NF-SMAs in binary polymer solar cells. The combination of dissymmetric core and precise replacement of selenophene on the central core is effective to improve J_sc and FF without sacrificing V_oc .

Recent Progress of Organic Photovoltaics with Efficiency over 17%

The power conversion efficiency (PCE) of organic photovoltaics (OPVs) has exceeded 18% with narrow bandgap, non-fullerene materials Y6 or its derivatives when used as an electron acceptor. The PCE improvement of OPVs is due to strong photon harvesting in near-infrared light range and low energy loss. Meanwhile, ternary strategy is commonly recognized as a convenient and efficient means to improve the PCE of OPVs. In this review article, typical donor and acceptor materials in prepared efficient OPVs are summarized. From the device engineering perspective, the typical research work on ternary strategy and tandem structure is introduced for understanding the device design and materials selection for preparing efficient OPVs.

Colloidal Lithography for Photovoltaics: An Attractive Route for Light Management

The pursuit of ever-more efficient, reliable, and affordable solar cells has pushed the development of nano/micro-technological solutions capable of boosting photovoltaic (PV) performance without significantly increasing costs. One of the most relevant solutions is based on light management via photonic wavelength-sized structures, as these enable pronounced efficiency improvements by reducing reflection and by trapping the light inside the devices. Furthermore, optimized microstructured coatings allow self-cleaning functionality via effective water repulsion, which reduces the accumulation of dust and particles that cause shading. Nevertheless, when it comes to market deployment, nano/micro-patterning strategies can only find application in the PV industry if their integration does not require high additional costs or delays in high-throughput solar cell manufacturing. As such, colloidal lithography (CL) is considered the preferential structuring method for PV, as it is an inexpensive and highly scalable soft-patterning technique allowing nanoscopic precision over indefinitely large areas. Tuning specific parameters, such as the size of colloids, shape, monodispersity, and final arrangement, CL enables the production of various templates/masks for different purposes and applications. This review intends to compile several recent high-profile works on this subject and how they can influence the future of solar electricity.

Surpassing 13% Efficiency for Polythiophene Organic Solar Cells Processed from Nonhalogenated Solvent

Benefiting from low cost and simple synthesis, polythiophene (PT) derivatives are one of the most popular donor materials for organic solar cells (OSCs). However, polythiophene-based OSCs still suffer from inferior power conversion efficiency (PCE) than those based on donor-acceptor (D-A)-type conjugated polymers. Herein, a fluorinated polythiophene derivative, namely P4T2F-HD, is introduced to modulate the miscibility and morphology of the bulk heterojunction (BHJ)-active layer, leading to a significant improvement of the OSC performance. The Flory-Huggins interaction parameters calculated from the surface energy and differential scanning calorimetry results suggest that P4T2F-HD shows moderate miscibility with the popular nonfullerene acceptor Y6-BO (2,2'-((2Z,2'Z)-((12,13-bis(2-butyloctyl)-3,9-diundecyl-12,13-dihydro-[1,2,5]thiadiazolo[3,4-e]thieno[2',3':4',5']thieno[2',3':4,5]pyrrolo[3,2-g]thieno[2',3':4,5]thieno[3,2-b]indole-2,10-diyl)bis(methanylylidene))bis(5,6-difluoro-3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile), while poly(3-hexylthiophene) (P3HT) is very miscible with Y6-BO. As a result, the P4T2F-HD case forms desired nanoscale phase separation in the BHJ film while the P3HT case forms a completely mixed BHJ film, as revealed by transmission electron microscopy (TEM) and grazing-incidence wide-angle X-ray scattering (GIWAXS). By optimizing the cathode interface and the morphology of the P4T2F-HD:Y6-BO films processed from nonhalogenated solvents, a new record PCE of 13.65% for polythiophene-based OSCs is demonstrated. This work highlights the importance of controlling D/A interactions for achieving desired morphology and also demonstrates a promising OSC system for potential cost-effective organic photovoltaics.

π-Extended Nonfullerene Acceptors for Efficient Organic Solar Cells with a High Open-Circuit Voltage of 0.94 V and a Low Energy Loss of 0.49 eV

A combination of high open-circuit voltage (V_oc) and short-circuit current density (J_sc) typically creates effective organic solar cells (OSCs). Y5, a member of the Y-series acceptors, can achieve high V_oc of 0.94 V with PM6 but low J_sc of 12.8 mA cm^-2. To maintain the high V_oc while increasing the J_sc of devices, we developed a new nonfullerene acceptor, namely, BTP-C2C4-N, by extending the conjugation of a Y5 molecule with a naphthalene-based end acceptor. In comparison with Y5-based devices, PM6:BTP-C2C4-N-based devices exhibited significantly higher J_sc of 18.2 mA cm^-2 followed by a high V_oc. To further increase the photovoltaic properties of BTP-C2C4-N analogues, BTP-C4C6-N and BTP-C6C8-N molecules with better processability and film morphology are obtained by adjusting the alkyl branched chain length. The optimized OSCs based on BTP-C4C6-N with a moderate alkyl branched chain length exhibited the best PCE of 12.4% with a high V_oc of 0.94 V and J_sc of 20.7 mA cm^-2. Notably, the devices achieved a low energy loss of 0.49 eV (0.51 eV for Y5 system) accompanied by a small nonradiative energy loss. The results indicate that nonfullerene acceptors with extended terminal motifs and optimized branched chain lengths can effectively enhance the performance of OSCs and reduce energy loss.

Becoming Sustainable, The New Frontier in Soft Robotics

The advancement of technology has a profound and far-reaching impact on the society, now penetrating all areas of life. From cradle to grave, one is supported by and depends on a wide range of electronic and robotic appliances, with an ever more intimate integration of the digital and biological spheres. These advances, however, often come at the price of negatively impacting our ecosystem, with growing demands on energy, contributions to greenhouse gas emissions and environmental pollution-from production to improper disposal. Mitigating these adverse effects is among the grand challenges of the society and at the forefront of materials research. The currently emerging forms of soft, biologically inspired electronics and robotics have the unique potential of becoming not only like their natural antitypes in performance and capabilities, but also in terms of their ecological footprint. This review outlines the rise of sustainable materials in soft and bioinspired robotics, targeting all robotic components from actuators to energy storage and electronics. The state-of-the-art in biobased robotics spans flourishing fields and applications ranging from microbots operating in vivo to biohybrid machines and fully biodegradable yet resilient actuators. These first steps initiate the evolution of robotics and guide them into a sustainable future.

Bromination and increasing the molecular conjugation length of the non-fullerene small-molecule acceptor based on benzotriazole for efficient organic photovoltaics

Two novel non-fullerene acceptors, namely BZIC-2Br and Y9-2Br, were synthesized by employing a ladder-type electron-deficient-based fused ring central with a benzotriazole core. Y9-2Br is obtained by extending the conjugate length of BZIC-2Br. Compared with BZIC-2Br, Y9-2Br possesses a lower optical bandgap of 1.32 eV with an absorption edge of 937 nm, exhibiting broader and stronger absorption band from 600 to 900 nm. Moreover, Y9-2Br exhibits excellent photovoltaic properties with V oc of 0.84 V, J sc of 21.38 mA cm-2 and FF of 67.11%, which achieves an impressive PCE of 12.05%. Our study demonstrates that bromination and effective extension of the conjugate length can modulate performance from different aspects to optimize photovoltaic characteristics.

Nonhalogenated Solvent-Processed High-Performance Indoor Photovoltaics Made of New Conjugated Terpolymers with Optimized Monomer Compositions

Conjugated random terpolymers, PJ-25, PJ-50, and PJ-75 were successfully synthesized from three different monomers. Fluorine-substituted benzotriazole (2F-BTA) was incorporated into 4,8-bis(4-chlorothiophen-2-yl)benzo[1,2-b:4,5-b']dithiophene (BDT-T-Cl) and a 1,3-bis(4-(2-ethylhexyl)thiophen-2-yl)-5,7-bis(2-alkyl)benzo[1,2-c:4,5-c']dithiophene-4,8-dione (BDD)-based alternating copolymer PM7 as a third monomeric unit. The solubility of the random terpolymers in nonhalogenated solvents increased with the number of 2F-BTA units in PM7. The random terpolymers were mixed with 3,9-bis(2-methylene-((3-(1,1-dicyanomethylene)-6,7-difluoro)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2',3'-d']-s-indaceno[1,2-b:5,6-b']dithiophene (IT-4F) to fabricate organic photovoltaic (OPV) cells. Among the three terpolymers and two related binary copolymers (e.g., PM7 and J52-Cl), outdoor photovoltaic (PV) cells (AM 1.5G) based on the PJ-50:IT-4F blend showed a high power conversion efficiency (PCE) of 11.34%. In addition, PJ-50 was employed as a donor in indoor PV (IPV) cells and was blended with nonfullerene acceptors, which have different absorption ranges. Among them, the PJ-50:IT-4F-based IPV device had the highest PCE of 17.41% with a J_sc of 54.75 μA cm^-2 and an FF of 0.77 under 160 μW cm^-2 light-emitting diode (LED) light. The terpolymer introduced in this study can be regarded as a promising material for the fabrication of outdoor PV and IPV cells with excellent performance involving the use of an eco-friendly solvent.

Alcohol-Soluble Zwitterionic 4-(Dimethyl(pyridin-2-yl)ammonio)butane-1-sulfonate Small Molecule as a Cathode Modifier for Nonfullerene Acceptor-Based Organic Solar Cells

A new zwitterionic small molecule 4-(dimethyl(pyridin-2-yl)ammonio)butane-1-sulfonate (PAS), synthesized from 2-dimethylaminopyrindine (2-DMAP), was developed for the ITO cathode modifier. PAS and 2-DMAP dissolved in methanol can form a thin layer on ITO cathode by a simple spin-coating process. The heteroatom moieties in 2-DMAP (sp² and sp³ nitrogen) and PAS (sp² nitrogen and sulfonate ion) can coordinate to the ITO surface and decrease the ITO work function by the induced surface dipoles. The fullerene-based (PBDTT-FTTE:PC₇₁BM) inverted OSCs using PAS and 2-DMAP interlayer can achieve PCEs of 8.95 and 8.26%, respectively, which are superior to the devices without a modifier (PCE = 3.25%) and comparable to the corresponding ZnO-based device (PCE = 8.57%). Nevertheless, 2-DMAP, like other nitrogen-containing polymer interlayer materials, turns out to be not applicable to inverted organic solar cells (I-OSCs) with IT-4F as the n-type electron acceptor because the amino group of 2-DMAP can act as a nucleophile to attack the end-group of IT-4F at the interface. The decomposition of IT-4F by 2-DMAP was carefully proved to be via retro-aldol condensation. As a result, the device (PBDBT-F:IT-4F) modified with 2-DMAP displayed a low PCE of 7.34%. The zwitterionic PAS with reduced nucleophilicity and basicity can modify the ITO surface without decomposing IT-4F. The PBDBT-F:IT-4F-based device modified with PAS maintained a high PCE of 11.41%. Most importantly, the PAS-based device using the well-known Y6 acceptor (PBDBT-F:Y6) can achieve a PCE of 13.82%. This new interfacial material can be universally applied to I-OSCs employing various A-D-A-type acceptors installed with the electrophilic 1,1-dicyanamethylene-5,6-difluoro-3-indanone (FIC) end-group.

From Y6 to BTPT-4F: a theoretical insight into the influence of the individual change of fused-ring skeleton length or side alkyl chains on molecular arrangements and electron mobility

Organic solar cells (OSCs) based on non-fullerene acceptor (NFA) Y6 have drawn tremendous attention due to the great progress in their power conversion efficiencies (PCEs).

Thermodynamic Properties and Molecular Packing Explain Performance and Processing Procedures of Three D18:NFA Organic Solar Cells

Organic solar cells (OSCs) based on D18:Y6 have recently exhibited a record power conversion efficiency of over 18%. The initial work is extended and the device performance of D18-based OSCs is compared with three non-fullerene acceptors, Y6, IT-4F, and IEICO-4Cl, and their molecular packing characteristics and miscibility are studied. The D18 polymer shows unusually strong chain extension and excellent backbone ordering in all films, which likely contributes to the excellent hole-transporting properties. Thermodynamic characterization indicates a room-temperature miscibility for D18:Y6 and D18:IT-4F near the percolation threshold. This corresponds to an ideal quench depth and explains the use of solvent vapor annealing rather than thermal annealing. In contrast, D18:IEICO-4Cl is a low-miscibility system with a deep quench depth during casting and poor morphology control and low performance. A failure of ternary blends with PC₇₁ BM is likely due to the near-ideal miscibility of Y6 to begin with and indicates that strategies for developing successful ternary or quaternary solar cells are likely very different for D18 than for other high-performing donors. This work reveals several unique property-performance relations of D18-based photovoltaic devices and helps guide design or fabrication of yet higher efficiency OSCs.

Eco-Friendly Polymer Solar Cells: Advances in Green-Solvent Processing and Material Design

Despite the recent breakthroughs of polymer solar cells (PSCs) exhibiting a power conversion efficiency of over 17%, toxic and hazardous organic solvents such as chloroform and chlorobenzene are still commonly used in their fabrication, which impedes the practical application of PSCs. Thus, the development of eco-friendly processing methods suitable for industrial-scale production is now considered an imperative research focus. This Review provides a roadmap for the design of efficient photoactive materials that are compatible with non-halogenated green solvents (e.g., xylenes, toluene, and tetrahydrofuran). We summarize the recent development of green processing solvents and the processing methods to match with the efficient photoactive materials used in non-fullerene solar cells. We further review progress in the use of more eco-friendly solvents (i.e., water or alcohol) for achieving truly sustainable and eco-friendly PSC fabrication. For example, the concept of water- or alcohol-dispersed nanoparticles made of conjugated materials is introduced. Also, recent important progress and strategies to develop water/alcohol-soluble photoactive materials that completely eliminate the use of conventional toxic solvents are discussed. Finally, we provide our perspectives on the challenges facing the current green processing methods and materials, such as large-area coating techniques and long-term stability. We believe this Review will inform the development of PSCs that are truly clean and renewable energy sources.

Highly Efficient and Photostable Ternary Organic Solar Cells Enabled by the Combination of Non-Fullerene and Fullerene Acceptors with Thienopyrrolodione-based Polymer Donors

Two polymer donors, PFBDT-8ttTPD and PClBDT-8ttTPD, consisting of halogenated thiophene-substituted benzo[1,2-b:4,5-b']dithiophene and alkyl-substituted thieno[3,2-b]thiophene linked thieno[3,4-c]pyrrole-4,6(5H)-dione, were designed and synthesized for the evaluation of photovoltaic performances. The fabricated IT-4F-based organic solar cells (OSCs) exhibited maximum power conversion efficiency (PCE) values of 12.81 and 11.12% for PFBDT-8ttTPD and PClBDT-8ttTPD, respectively. Furthermore, PFBDT-8ttTPD:Y6 showed significantly improved PCE (15.05%) due to the extended light harvesting in the broad solar spectrum, whereas the PClBDT-8ttTPD:Y6 displayed relatively low PCE (10.02%). A ternary system incorporating PC₇₁BM as the third component into bulk-heterojuction composites (PFBDT-8ttPTD:non-fullerene) was investigated with the aim of utilizing the advantages of PC₇₁BM. As a result, PFBDT-8ttTPD:IT-4F:PC₇₁BM exhibited an improved PCE (13.67%) compared to that of the corresponding binary OSC. In particular, ternary OSC of PFBDT-8ttTPD:Y6:PC₇₁BM showed outstanding photovoltaic performance (PCE = 16.43%) as well as photostability, retaining approximately 80% of the initial PCE after 500 h under continuous illumination. The introduction of a small amount of PC₇₁BM resulted in favorable and dense molecular packing with improved crystallinity as well as enhanced charge carrier mobility for efficient OSC.

Tuning fullerene miscibility with porphyrin-terminated P3HTs in bulk heterojunction blends

Understanding and manipulating the miscibility of donor and acceptor components in the active layer morphology is important to optimize the longevity of organic photovoltaic devices and control power conversion efficiency. In pursuit of this goal, a "porphyrin-capped" poly(3-hexylthiophene) was synthesized to take advantage of strong porphyrin:fullerene intermolecular interactions that modify fullerene miscibility in the active layer. End-functionalized poly(3-hexylthiophene) was synthesized via catalyst transfer polymerization and subsequently functionalized with a porphyrin moiety via post-polymerization modification. UV-vis spectroscopy and X-ray diffraction measurements show that the porphyrin-functionalized poly(3-hexylthiophene) exhibits increased intermolecular interactions with phenyl-C61-butyric acid methyl ester (PCBM) in the solid state compared to unfunctionalized poly(3-hexylthiophene) without sacrificing microstructure ordering that facilitates optimal charge transport properties. Additionally, differential scanning calorimetry revealed porphyrin-functionalized poly(3-hexylthiophene) crystallization decreased only slightly (1-6%) compared to unfunctionalized poly(3-hexylthiophenes) while increasing fullerene miscibility by 55%. Preliminary organic photovoltaic device results indicate device power conversion efficiency is sensitive to additive loading levels, as evident by a slight increase in power conversion efficiency at low additive loading levels but a continuous decrease with increased loading levels. While the increased fullerene miscibility is not balanced with significant increases in power conversion efficiency, this approach suggests that integrating non-bonded interaction potentials is a useful pathway for manipulating the morphology of the bulk heterojunction thin film, and porphyrin-functionalized poly(3-hexylthiophenes) may be useful additives in that regard.

Aggregation Tuning with Heavily Fluorinated Donor Polymer for Efficient Organic Solar Cells

The fluorination/sulfofication-induced effect in the photovoltaic polymer solar cells (PSCs) needs to be paid much attention. In this work, a new donor polymer PBDB-PS2F was synthesized by heavily fluorinated and decorated S atom on the side chain of benzo[1,2-b:4,5-b']dithiophene (BDT) unit to explore the internal combined effect of F&S on the photoelectric performance. It was found that the heavy fluorination on the side chain could make PBDB-PS2F achieve a low highest occupied molecule orbital (HOMO) energy level of -5.72 eV and weaken the torsion of the main chain and effectively increase the intermolecular π-π* transition. Encouragingly, compared with the counterpart polymer PBDB-PS without the fluorination, PBDB-PS2F exhibited a much intense aggregation at room temperature but showed a tendency of reduced aggregation at high temperatures. This feature gives excellent solution processability and uniform morphology in the active layer of a PBDB-PS2F-based device, enabling an outstanding photovoltaic performance with the power conversion efficiency (PCE) of 13.56% (V_OC = 0.90 V, J_SC = 21.53 mA/cm², FF = 69.68%). Compared with that of the counterpart polymer PBDB-PS with no heavy fluorination, the V_OC of PBDB-PS2F increased by 15.4% and the PCE increased by 30.9%. Thus, the heavy-fluorination-induced effect to construct photovoltaic polymers could be used to improve the performance of polymer solar cells.

17% Non-Fullerene Organic Solar Cells with Annealing-Free Aqueous MoO x

A charge transport layer based on transition metal-oxides prepared by an anhydrous sol-gel method normally requires high-temperature annealing to achieve the desired quality. Although annealing is not a difficult process in the laboratory, it is definitely not a simple process in mass production, such as roll-to-roll, because of the inevitable long cooling step that follows. Therefore, the development of an annealing-free solution-processable metal-oxide is essential for the large-scale commercialization. In this work, a room-temperature processable annealing-free "aqueous" MoO x solution is developed and applied in non-fullerene PBDB-T-2F:Y6 solar cells. By adjusting the concentration of water in the sol-gel route, an annealing-free MoO x with excellent electrical properties is successfully developed. The PBDB-T-2F:Y6 solar cell with the general MoO x prepared by the anhydrous sol-gel method shows a low efficiency of 7.7% without annealing. If this anhydrous MoO x is annealed at 200 °C, the efficiency is recovered to 17.1%, which is a normal value typically observed in conventional structure PBDB-T-2F:Y6 solar cells. However, without any annealing process, the solar cell with aqueous MoO x exhibits comparable performance of 17.0%. In addition, the solar cell with annealing-free aqueous MoO x exhibits better performance and stability without high-temperature annealing compared to the solar cells with PEDOT:PSS.

Isomeric Effect of Wide Bandgap Polymer Donors with High Crystallinity to Achieve Efficient Polymer Solar Cells

Two highly crystalline polymer donors (PBTz4T2C-a, PBTz4T2C-b) with isomers (4T2C-a, 4T2C-b) are synthesized and applied in polymer solar cells. The developed polymers possess proper energy levels and complementary absorption with an efficient electron acceptor IT2F. It is interesting that the photophysical properties, crystallinity, and active layer morphology characteristic can be significantly changed by just slightly regulating the substitution position of the carboxylate groups. A series of simulation calculations of the two isomers are conducted in the geometry and electronic properties to explore the difference induced by the position adjustment of carboxylate groups. The results decipher that 4T2C-b moiety features much stronger intramolecular noncovalent S⋯O interactions compared to that of 4T2C-a, implying a higher coplanarity and much stronger crystallinity, and leading to excessive phase separation in PBTz4T2C-b:IT2F blend film. In contrast, PBTz4T2C-a with 4T2C-a moiety exhibits suitable crystallinity with a lower the highest occupied molecular orbital level, higher film absorption coefficient, and charge mobilities, resulting in a much higher power conversion efficiency of 11.02%. This research demonstrates that the molecular conformation is of great importance to be considered for developing high-performance polymer donors.

Hot Hydrocarbon-Solvent Slot-Die Coating Enables High-Efficiency Organic Solar Cells with Temperature-Dependent Aggregation Behavior

Organic solar cells (OSCs) have made rapid progress in terms of their development as a sustainable energy source. However, record-breaking devices have not shown compatibility with large-scale production via solution processing in particular due to the use of halogenated environment-threatening solvents. Here, slot-die fabrication with processing involving hydrocarbon-based solvents is used to realize highly efficient and environmentally friendly OSCs. Highly compatible slot-die coating with roll-to-roll processing using halogenated (chlorobenzene (CB)) and hydrocarbon solvents (1,2,4-trimethylbenzene (TMB) and ortho-xylene (o-XY)) is used to fabricate photoactive films. Controlled solution and substrate temperatures enable similar aggregation states in the solution and similar kinetics processes during film formation. The optimized blend film nanostructures for different solvents in the highly efficient PM6:Y6 blend is adopted to show a similar morphology, which results in device efficiencies of 15.2%, 15.4%, and 15.6% for CB, TMB, and o-XY solvents. This approach is successfully extended to other donor-acceptor combinations to demonstrate the excellent universality of this method. The results combine a method to optimize the aggregation state and film formation kinetics with the fabrication of OSCs with environmentally friendly solvents by slot-die coating, which is a critical finding for the future development of OSCs in terms of their scalable production and high-performance.

Substitution Effect on Thiobarbituric Acid End Groups for High Open-Circuit Voltage Non-Fullerene Organic Solar Cells

Recent advances in non-fullerene acceptors (NFAs) have resulted in significant improvement in the power conversion efficiencies (PCEs) of organic solar cells (OSCs). In our efforts to boost open-circuit voltage (V_OC) for OSCs, the molecular design employing thiobarbituric acid (TBTA) end groups and an indacenodithieno[3,2-b]thiophene (IDTT) core gives rise to NFAs with significantly raised lowest unoccupied molecular orbital (LUMO) energy level, which, when paired with PCE10, can achieve V_OC's over 1.0 V and decent PCEs that outperform the equivalent devices based on the benchmark ITIC acceptor. While the use of a TBTA end group is effective in tuning energy levels, very little is known about how the alkyl substitution on the TBTA group impacts the solar cell performance. To this end, TBTA end groups are alkylated with linear, branched, and aromatic sidechains to understand the influence on thin-film morphology and related device performances. Our study has confirmed the dependence of solar cell performance on the end-group substituents. More importantly, we reveal the presence of an ideal window of crystallinity associated with the medium-length hydrocarbon chains such as ethyl and benzyl. Deviation to the shorter methyl group makes the acceptor too crystalline to mix with the polymer donor and form proper domains, whereas longer and branched alkyl chains are too sterically bulky and hinder charge transport due to nonideal packing. Such findings underline the comprehensive nature of thin-film morphology and the subtle end-group effects for the design of non-fullerene acceptors.