Determination of 136 pharmaceuticals and hormones in sewage sludge using quick, easy, cheap, effective, rugged and safe extraction followed by analysis with liquid chromatography-time-of-flight-mass spectrometry

Extraction Efficiency of a Commercial Espresso Machine Compared to a Stainless-Steel Column Pressurized Hot Water Extraction (PHWE) System for the Determination of 23 Pharmaceuticals, Antibiotics and Hormones in Sewage Sludge

Two green chemistry extraction systems, an in-house stainless-steel column Pressurized Hot Water Extraction system (PHWE) and a commercially available Espresso machine were applied for analysing 23 active pharmaceutical ingredients (APIs) in sewage sludge. Final analysis was performed on UPLC-MS/MS using two different chromatographic methods: acid and basic. When analysing all 23 APIs in sewage sludge both extraction methods showed good repeatability. The PHWE method allowed for a more complete extraction of APIs that were more tightly bound to the matrix, as exemplified by much higher concentrations of e.g., ketoconazole, citalopram and ciprofloxacin. In total, 19 out of 23 investigated APIs were quantified in sewage sludge, and with a few exceptions the PHWE method was more exhaustive. Mean absolute recoveries of 7 spiked labelled APIs were lower for the PHWE method than the Espresso method. Under acid chromatographic conditions mean recoveries were 16% and 24%, respectively, but increased to 24% and 37% under basic conditions. The difference between the PHWE method and the Espresso method might be interpreted as the Espresso method giving higher extraction efficiency; however, TIC scans of extracts revealed a much higher matrix co-extraction for the PHWE method. Attempts were made to correlate occurrence of compounds in sewage sludge with chemical properties of the 23 APIs and there are strong indications that both the number of aromatic rings and the presence of a positive charge is important for the sorption processes to sewage sludge.

Simultaneous Determination of Pharmaceuticals by Solid-phase Extraction and Liquid Chromatography-Tandem Mass Spectrometry: A Case Study from Sharjah Sewage Treatment Plant

The present work describes the optimization and validation of a highly selective and sensitive analytical method using solid phase extraction and liquid chromatography tandem mass spectrometry (SPE LC-MS/MS) for the determination of some frequently prescribed pharmaceuticals in urban wastewater received and treated by Sharjah sewage treatment plant (STP). The extraction efficiency of different SPE cartridges was tested and the simultaneous extraction of pharmaceuticals was successfully accomplished using hydrophilic-lipophilic-balanced reversed phase Waters^® Oasis HLB cartridge (200 mg/ 6 mL) at pH 3. The analytes were separated on an Aquity BEH C18 column (1.7 µm, 2.1 mm × 150 mm) using gradient elution and mass spectrometric analysis were performed in multiple reactions monitoring (MRM) selecting two precursor ions to produce ion transition for each pharmaceutical using positive electrospray ionization (+ESI) mode. The correlation coefficient values in the linear calibration plot for each target compound exceeded 0.99 and the recovery percentages of the investigated pharmaceuticals were more than 84%. Limit of detection (LOD) varied between 0.1–1.5 ng/L and limit of quantification (LOQ) was 0.3–5 ng/L for all analytes. The precision of the method was calculated as the relative standard deviation (RSD%) of replicate measurements and was found to be in the ranges of 2.2% to 7.7% and 2.2% to 8.6% for inter and intra-day analysis, respectively. All of the obtained validation parameters satisfied the requirements and guidelines of analytical method validation.

Comparative characterization of surface sludge deposits from fourteen French Vertical Flow Constructed Wetlands sewage treatment plants using biological, chemical and thermal indices

Due to their design and mode of operation, French Vertical Flow Constructed Wetlands (VFCWs) accumulate suspended solids from the inflow wastewater in the form of a sludge layer at the surface of the first filter. In order to maintain the treatment performance over the long term, the characteristics of the sludge deposits and their evolution have to be well described. In this objective, a panel of sludge deposit samples taken from 14 French VFCW sewage treatment plants was investigated. Elemental composition and organic matter content, nature and reactivity were analyzed. Results clearly revealed two categories of sludge deposits, namely the "young-age plants" type (1 year of operation and less) and the "mature plants" type (3 years of operation and more). Sludge deposits from the "mature plants" exhibited same biological, physical and chemical properties. Their organic matter was globally less abundant, more humified and less biodegradable than in the young-age plants type. Their overall contents in trace metals were also higher, although in a limited manner. The effect of additional treatments, particularly FeCl₃ injection for phosphorus precipitation, was observable in the "young-age plants" group. Finally, the sludge deposits sampled from one particular plant with specific operating conditions were found to exhibit very different characteristics from those of either groups identified. This observation underlined the influence of local conditions on the typology of the sludge deposits.

Analysis of pharmaceutical biodegradation of WWTP sludge using composting and identification of certain microorganisms involved in the process

Pharmaceuticals (PhCs) are organic contaminants that have been detected in wastewater, surface water, and soils throughout the world. The presence of 10 commonly used PhCs in Spain (azithromycin, benzylpenicillin, citalopram, fluconazole, fluoxetine, ibuprofen, irbesartan, olanzapine, telmisartan, and venlafaxine) was analysed at four wastewater treatment plants, and the changes in their concentrations during treatment were assessed. Although certain some PhCs were degraded in the treated water, their presence in sewage sludge increased in all cases. The sewage sludge was composted using rice straw to degrade the PhCs, and the composting efficiency was modified by changes in the relative C/N ratio of the composting blend. Using a simple microbiological culture process for enrichment, 11 different strains of microorganisms that degraded specific PhCs were identified. Ibuprofen and azithromycin were metabolized by one and four strains, respectively, and both PhCs were used as a carbon source; in addition, six strains used irbesartan as a nitrogen source.

A pressurized liquid extraction approach followed by standard addition method and UPLC-MS/MS for a fast multiclass determination of antibiotics in a complex matrix

In this work a fast analytical method for the determination of macrolides, tetracyclines and fluoroquinolones in a compost originating from a mixture of sewage sludge, palm waste and grass was developed by ultra-high performance liquid chromatography coupled to mass spectrometry (U-HPLC/MS). Antibiotics were extracted from compost by using the accelerated solvent extraction (ASE). The chromatographic separation was carried out on a T3 Cortecs C18 column using a mobile phase gradient mixture of water acidified with 1% of formic acid and acetonitrile. Recoveries of 24-30%, 53-93%, 33-57%, 69-135% and 100-171% were obtained for roxithromycin (ROX), chlortetracycline (CTC), oxytetracycline (OTC), enrofloxacin (ENR) and ciprofloxacin (CIP), respectively. As the most part of antibiotics showed significant matrix effect (ME), the method was validated using the standard addition method (SAM) to correct the observed ME. Instrumental variation, of LC/MS system, showed that 93.75% of the relative standard deviation (RSD %) are below 15%, although the organic load of extracts. This analytical method was applied to assess the fate of antibiotics during composting. Two composting experiments were conducted separately after spiking sludge at 2 different concentrations levels. The resulting elimination rates were of 52-76, 69-100, 100 and 24-50% for ROX, CTC, OTC and CIP, respectively. These results suggest that composting process contributes to the removal of residuals concentrations of macrolides and tetracyclines while the fluoroquinolones persist in the final compost product.

Sample as solid support in MSPD: A new possibility for determination of pharmaceuticals, personal care and degradation products in sewage sludge

A method based on matrix-solid phase dispersion (MSPD), focused on the principles of green analytical chemistry, aimed at the use of alternative solid supports and less toxic solvents, was developed for the simultaneous determination of 19 pharmaceuticals, 4 personal care products (PPCPs) and 4 degradation products in sewage sludge samples. Higher recoveries were achieved when 2 g sample was macerated for 5 min in a glass mortar, transferred to a centrifuge tube, and 1 min vortex agitation with 5 mL methanol. The performance of the method was evaluated through linearity, recovery, precision (intra-day), method detection and quantification limits (MDL and MQL) and matrix effect. The calibration curves prepared in methanol and in the matrix extract showed a correlation coefficient ranging from 0.98 to 0.99. MQL values ranged from 1.25 to 1250 ng g^-1. Recoveries between 50 and 120% were reached with RSDs lower than 20% for most compounds. The method presented low and medium matrix effects for most analytes. This method was successfully applied to real samples and of the 27 compounds determined, amitriptyline, carbamazepine, diclofenac, haloperidol, ketoconazole, miconazole, albendazole, mebendazole, thiabendazole, triclosan and triclocarban were detected in concentrations between 2.5 and 5400 ng g^-1.

Photolytic and photocatalytic transformation of an antipsychotic drug asenapine: Comparison of kinetics, identification of transformation products, and in silico estimation of their properties

The photolytic and photocatalytic transformation of an antipsychotic drug asenapine with the use of H₂O₂ and TiO₂ was studied. A method employing irradiation with a simulated full solar spectrum in the photostability chamber was applied, then the reverse-phase ultra high performance liquid chromatography with diode array detector, coupled with electrospray quadrupole time-of-flight mass spectrometer (RP-UHPLC-DAD - ESI-Q-TOF) was used for the quantitative and qualitative analysis of the processes. The developed quantitative method was fully validated, according to the International Conference on Harmonization of Technical Requirements for Registration of Pharmaceuticals for Human Use (ICH) guidelines, and the kinetic parameters of asenapine photodecomposition were compared. Nineteen phototransformation products were detected, and their probable structures - mainly hydroxylated and oxidized asenapine derivatives - were suggested. On the basis of the elucidated structures the computational prediction of their toxicity at the various endpoints, as well as bioconcentration factors and biodegradability was performed. The obtained results were then subjected to the principal component analysis (PCA). This chemometric technique facilitated comparison of the applied models, calculated properties of the TPs, and enabled visualization of relationships between them.

Assessment of human exposure to triclocarban, triclosan and five parabens in U.S. indoor dust using dispersive solid phase extraction followed by liquid chromatography tandem mass spectrometry

Antimicrobials in indoor dust pose concerns due to their endocrine disrupting activities and potential promotion of antibiotic resistance. We adopted dispersive solid phase extraction (d-SPE) and liquid chromatography-tandem mass spectrometry (LC-MS/MS) to quantify antimicrobials in dust. The method showed favorable linearity (R² >0.99), recovery (83-115%), and method detection limits (1.2-5.6 ng/g, dry weight). All seven analytes were found at median concentrations in ng/g in each of the 80 U.S. dust samples collected from athletic facilities and residential homes: methyl paraben (1920) > propyl paraben (965) > triclosan (390) > triclocarban (270) > ethyl paraben (195) > butyl paraben (80) > benzyl paraben (6). Triclosan levels in dust from athletic facilities were significantly higher than those in private homes (p < 0.05). Median estimated daily intake (EDI) of antimicrobials in ng/kg-body weight/d from dust ingestion was lowest for adults (1.9) and higher for more sensitive subpopulations, including infants (19.8), toddlers (23.6), children (11.8) and teenagers (4.6). This first application of d-SPE to the analysis of dust produced U.S. baseline data for triclosan and triclocarban levels in indoor dust just prior to the 2017 Federal ban on use of these trichlorinated aromatics in antiseptic soaps and related personal care products.

A review of the pharmaceutical exposome in aquatic fauna

Pharmaceuticals have been considered 'contaminants of emerging concern' for more than 20 years. In that time, many laboratory studies have sought to identify hazard and assess risk in the aquatic environment, whilst field studies have searched for targeted candidates and occurrence trends using advanced analytical techniques. However, a lack of a systematic approach to the detection and quantification of pharmaceuticals has provided a fragmented literature of serendipitous approaches. Evaluation of the extent of the risk for the plethora of human and veterinary pharmaceuticals available requires the reliable measurement of trace levels of contaminants across different environmental compartments (water, sediment, biota - of which biota has been largely neglected). The focus on pharmaceutical concentrations in surface waters and other exposure media have therefore limited both the characterisation of the exposome in aquatic wildlife and the understanding of cause and effect relationships. Here, we compile the current analytical approaches and available occurrence and accumulation data in biota to review the current state of research in the field. Our analysis provides evidence in support of the 'Matthew Effect' and raises critical questions about the use of targeted analyte lists for biomonitoring. We provide six recommendations to stimulate and improve future research avenues.

Investigation of the photolysis and TiO2, SrTiO3, H2O2-mediated photocatalysis of an antipsychotic drug loxapine - Evaluation of kinetics, identification of photoproducts, and in silico estimation of properties

The photolytic and photocatalytic transformation of loxapine with the use of H₂O₂, TiO₂ and SrTiO₃ under the simulated solar radiation was studied. A micro-scale method for simultaneous irradiation of multiple samples in photostability chamber was applied. RP-UHPLC-DAD coupled with ESI-Q-TOF mass spectrometer was used for the quantitative and qualitative analysis of the processes. Influence of catalysts concentration on kinetic parameters of loxapine photodecomposition was evaluated, and TiO₂ at medium concentration (100 mg L^-1) turned out to be the most effective. Sixteen transformation products were detected and their structures were elucidated. On the basis of the elucidated structures, computational evaluation of toxicity, bioconcentration and bioaccumulation factors as well as biodegradability of transformation products were conducted. The multivariate chemometric method (principal component analysis) was used to compare the calculated properties as well as the applied methods. Most of the transformation products were generally less toxic and more biodegradable than the parent compound.

Development and validation of a comprehensive solid-phase extraction method followed by LC-TOF/MS for the analysis of eighteen pharmaceuticals in influent and effluent of sewage treatment plants

The scarcity of data about the occurrence of pharmaceuticals in water bodies in Malaysia prompted us to develop a suitable analytical method to address this issue. We therefore developed a method based on solid-phase extraction combined with liquid chromatography-time of flight/mass spectrometry (SPE-LC-TOF/MS) for the analysis of sixteen prescribed and two nonprescribed pharmaceuticals that are potentially present in water samples. The levels of these pharmaceuticals, which were among the top 50 pharmaceuticals consumed in Malaysia during the period 2011-2014, in influent and effluent of five sewage treatment plants (STPs) in Bangi, Malaysia, were then analyzed using the developed method. All of the pharmaceuticals were separated chromatographically using a 5 μm, 2.1 mm × 250 mm C18 column at a flow rate of 0.3 mL/min. Limits of quantification (LOQs) were 0.3-8.2 ng/L, 6.5-89 ng/L, and 11.1-93.8 ng/L in deionized water (DIW), STP effluent, and STP influent, respectively, for most of the pharmaceuticals. Recoveries were 51-108%, 52-118%, and 80-107% from the STP influent, STP effluent, and DIW, respectively, for most of the pharmaceuticals. The matrix effect was also evaluated. The signals from carbamazepine, diclofenac sodium, and mefenamic acid were found to be completely suppressed in the STP influent. The signals from other compounds were found to be influenced by matrix effects more strongly in STP influent (enhancement or suppression of signal ≤180%) than in effluent (≤94%). The signal from prednisolone was greatly enhanced in the STP influent, indicating a matrix effect of -134%. Twelve pharmaceuticals were frequently detected in all five STPs, and caffeine, prazosin, and theophylline presented the highest concentrations among all the pharmaceuticals monitored: up to 7611, 550, and 319 ng/L in the STP influent, respectively. To the best of our knowledge, this is the first time that prazosin has been detected in a water matrix in Malaysia. Graphical abstract ᅟ.

Occurrence and fate of emerging contaminants in municipal wastewater treatment plants from different geographical regions-a review

Emerging contaminants, such as antibiotics, pharmaceuticals, personal care products, hormones, and artificial sweeteners, are recognized as new classes of water contaminants due to their proven or potential adverse effects on aquatic ecosystems and human health. This review provides comprehensive data on the occurrence of 60 emerging contaminants (ECs) in influent, treated effluent, sludge, and biosolids in wastewater treatment plants (WWTPs). In particular, data on the occurrence of ECs in the influents and effluents of WWTPs are systematically summarized and categorized according to geographical regions (Asia, Europe, and North America). The occurrence patterns of ECs in raw influent and treated effluents of WWTPs between geographical regions were compared and evaluated. Concentrations of most ECs in raw influent in Asian region tend to be higher than those in European and North American countries. Many antibiotics were detected in the influents and effluents of WWTPs at concentrations close to or exceeding the predicted no-effect concentrations (PNECs) for resistance selection. The efficacy of EC removal by sorption and biodegradation during wastewater treatment processes are discussed in light of kinetics and parameters, such as sorption coefficients (K_d) and biodegradation constants (k_biol), and physicochemical properties (i.e. log K_ow and pK_a). Commonly used sampling and monitoring strategies are critically reviewed. Analytical research needs are identified, and novel investigative approaches for future monitoring studies are proposed.

Photolytic and photocatalytic degradation of tandospirone: Determination of kinetics, identification of transformation products and in silico estimation of toxicity

The photolytic and photocatalytic transformation of tandospirone with the use of TiO₂ and H₂O₂ was investigated. A micro-scale method for simultaneous irradiation with simulated full solar spectrum of multiple samples in photostability chamber was proposed. RP-UHPLC-DAD coupled with ESI-Q-TOF mass spectrometer was used for the quantitative and qualitative analysis of the processes. The developed method was fully validated and the kinetic parameters of tandospirone photodegradation were compared. The structures of eighteen photoproducts as well as phototransformation pathways were proposed. Based on the elucidated structures, computational toxicity assessment with the use of various software was performed and most of the photoproducts were found as less or similarly toxic to the parent compound. Nevertheless, several products, including one of the drug main metabolites, were significantly more toxic than the parent drug. The multivariate chemometric method (principal component analysis) was used to compare the toxicity of phototransformation products as well as the toxicity of the assessment methods.

Simultaneous Determination of Fluoroquinolones and Sulfonamides Originating from Sewage Sludge Compost

A simultaneous method for quantitative determination of traces of fluoroquinolones (FQs) and sulfonamides (SAs) in edible plants fertilized with sewage sludge was developed. The compounds were extracted from the plants by rapid and simple liquid extraction followed by extracts clean-up using solid phase extraction. The eluent additive 1,1,1,3,3,3-hexafluoro-2-propanol was used for liquid chromatographic detection to achieve separation of structurally similar antimicrobials like ciprofloxacin and norfloxacin. Identification and quantification of the compounds were performed using high-performance liquid chromatography with electrospray ionization mass spectrometry in selected reaction monitoring mode. Method was validated and extraction recoveries of FQs and SAs ranged from 66% to 93%. The limit of quantifications was from 5 ng/g in the case of ofloxacin to 40 ng/g for norfloxacin. The method precision ranged from 1.43% to 2.61%. The developed novel method was used to evaluate the plats antimicrobial uptake (potato (Solanum tuberosum L.), carrot (Daucus carota L.), lettuce (Lactuca sativa L.), and wheat (Triticum vulgare L.)) from soil and migration of the analytes inside the plants.

Liquid chromatography quadrupole time-of-flight mass spectrometry identification and determination of tri- and hexaaryl chloro imidazoles in sewage sludge

The identification and further quantification of 2-chloro-triarylimidazole (o-Cl-TAI) and its dimer (o-DCl-HABI) in sludge from a sewage treatment plant (STP) is reported for the first time. Liquid chromatography (LC) quadrupole time-of-flight (QTOF) mass spectrometry (MS) was used as analytical technique during screening and determination steps. Pollutants were identified following a post-run search strategy, applying the chlorine mass filter, and characterized by their accurate MS and product ion scan spectra. Finally, their identities were confirmed with authentic standards. The species (o-Cl-TAI) has been rated as potentially genotoxic and carcinogenic for mice and rats. Effects of sample preparation in the stability and the extraction efficiency of both compounds are discussed. Under final conditions, they were extracted from freeze-dried samples (0.5 g of sludge or biosolids dispersed with 2 g of C₁₈ and packed into a polypropylene syringe) with 20 ml of methanol, which also flowed through a clean-up layer of Florisil and PSA sorbents (0.5 g each). This method attained quantitative extraction yields and limits of quantification between 4 and 10 ng/g. The pollutants o-Cl-TAI and o-DCl-HABI were ubiquitous in sludge and biosolids obtained in consecutive years from the investigated STP. Their concentrations varied from 0.02 to more than 13 μg/g (freeze-dried sample). Copyright © 2016 John Wiley & Sons, Ltd.

Determination and characterization of pharmaceuticals in sludge from municipal and livestock wastewater treatment plants

This study investigated 24 pharmaceuticals compounds belonging to the classes of analgesics, stimulants, anti-seizures, non-steroidal anti-inflammatory drugs (NSAIDs), and antibiotics in the sludge of 12 municipal sewage treatment plants (S-sludge) and 4 livestock wastewater treatment plants (L-sludge) located across Korea. Over 70% of the target compounds were detected in at least one sample of S-sludge and L-sludge. The total concentration of the target pharmaceutical compounds detected in S-sludge was 2.622-422.8 mg kg^-1and the most dominant compound was acetylsalicylic acid (ASA: 0.374-367.0 mg kg^-1) whereas in L-sludge, the total concentration was 43.87-156.8 mg kg^-1and the most abundant compound was oxytetracycline (OTC: 34.54-86.39 mg kg^-1). Cluster analysis revealed two distinct groups: group A, which were S-sludge samples including ASA, carbamazepine (CBM), and others, and group B were L-sludge samples, dominated by antibiotics (CTC, OTC, LIN). The total daily load amount of the target pharmaceuticals in S-sludge was 0.010-268.9 kg day^-1 while the L-sludge was 0.021-0.529 kg day^-1. The estimated amounts of the target pharmaceutical discharged from S-sludge and L-sludge into the Korean environment were 150.2 ± 47.94 ton yr^-1 and 15.05 ± 5.671 ton yr^-1 respectively, but the discharged amount of antibiotics from S-sludge (6.945 ton yr^-1) was lower than that from L-sludge (9.234 ton yr^-1).

Evaluation of SimpleTreat 4.0: Simulations of pharmaceutical removal in wastewater treatment plant facilities

In this study, the removal of pharmaceuticals from wastewater as predicted by SimpleTreat 4.0 was evaluated. Field data obtained from literature of 43 pharmaceuticals, measured in 51 different activated sludge WWTPs were used. Based on reported influent concentrations, the effluent concentrations were calculated with SimpleTreat 4.0 and compared to measured effluent concentrations. The model predicts effluent concentrations mostly within a factor of 10, using the specific WWTP parameters as well as SimpleTreat default parameters, while it systematically underestimates concentrations in secondary sludge. This may be caused by unexpected sorption, resulting from variability in WWTP operating conditions, and/or QSAR applicability domain mismatch and background concentrations prior to measurements. Moreover, variability in detection techniques and sampling methods can cause uncertainty in measured concentration levels. To find possible structural improvements, we also evaluated SimpleTreat 4.0 using several specific datasets with different degrees of uncertainty and variability. This evaluation verified that the most influencing parameters for water effluent predictions were biodegradation and the hydraulic retention time. Results showed that model performance is highly dependent on the nature and quality, i.e. degree of uncertainty, of the data. The default values for reactor settings in SimpleTreat result in realistic predictions.

Studies on photodegradation process of psychotropic drugs: a review

Consumption of psychotropic drugs is still increasing, especially in high-income countries. One of the most crucial consequences of this fact is significant release of them to the environment. Considerable amounts of atypical antipsychotics, benzodiazepines, antidepressants, and their metabolites were detected in river, lake, and sea water, as well as in tissues of aquatic organisms. Their ecotoxicity was proved by numerous studies. It should be noticed that interaction between psychotropic pharmaceuticals and radiation may lead to formation of potentially more toxic intermediates. On the other hand, photo-assisted wastewater treatment methods can be used as an efficient way to eliminate them from the environment. Many methods based on photolysis and photocatalysis were proposed and developed recently; nevertheless, the problem is still unsolved. However, according to recent studies, photocatalysis could be considered as the most promising and far more effective than regular photolysis. An overview on photolytic as well as homogenous and heterogeneous photocatalytic degradation methods with the use of various catalysts is presented. The photostability and phototoxicity of pharmaceuticals were also discussed. Various analytical methods were used for the photodegradation research, and this issue was also compared and summarized. Use of high-resolution multistage mass spectrometry (Q-TOF, ion trap, Orbitrap) was suggested. The combined techniques such as LC-MS, GC-MS, and LC-NMR, which enable qualitative and quantitative analyses in one run, proved to be the most valuable in this case. Assembling of MS/MS spectra libraries of drug molecules and their phototransformation products was identified as the future challenge.

Fate of emerging and priority micropollutants during the sewage sludge treatment: Case study of Paris conurbation. Part 1: Contamination of the different types of sewage sludge

This article provides data on the contamination of different kinds of sludge (raw, centrifuged, digested, thermally dried sludge and sludge cake) from Paris conurbation by 71 various pollutants including pharmaceutical products (PHPs), hormones, perfluorinated acids (PFAs), linear alkylbenzene sulfonate (LAS), alkylphenols (APs), phthalates (PAEs), polycyclic aromatic hydrocarbons (PAHs) and polychlorobiphenyls (PCBs). Very high contents of LAS (0.1-10g/kg dry matter - DM) compared to other compounds were found in all types of sludge followed by DEHP (10-100mg/kg DM) and fluoroquinolones (1-100mg/kg DM). APs were measured at intermediary contents in Parisian sludge, lying in the 2-20mg/kg DM range. Finally, hormones, PAHs, PCBs, PAEs, PFAs and the remaining PHPs were all found at contents lower than 1mg/kg DM. For most compounds (PHPs, PFOS, DEHP, PAHs), no significant differences in the micropollutant contents were found for similar types of sludge from different WWTP in Paris, highlighting the homogeneity of sludge contamination in downstream Paris catchment. The variability of concentration is rather high (coefficient of variation >100%) for several PHPs, PFAs or PCBs while it is moderate (<100%) or low (<50%) for fluoroquinolones, hormones, PAHs, APs or LAS. In addition, digestion seems to have a buffer effect as variabilities are lower in digested sludge for PHPs, PFAs, APs and PCBs. During sludge treatment (centrifugation, digestion, thermal drying, sludge conditioning+press filtration), the hormones, LAS, APs, PAHs, DEHP and PCBs concentrations increased, while those of PHPs and PFAs decreased. In the case of digestion, the increase of content can be explained by no pollutant removal or a lower removal than DM removal (concentration phenomenon) whereas the decrease underlines that the compound is more removed than the DM. In any case, these concentration variations presuppose the mechanisms of dissipation that could be attributed to volatilization, biotic or abiotic transformation (complete or with metabolites production), bound residues formation. In addition, data on sludge liquors - centrifuged (CW) and condensed (TDW) waters - from respectively centrifugation and thermal drying were collected. Several hormones, PHPs, PFAs, LAS, PAEs, APs, PCBs and PAHs were quantified in CW and TDW, displaying a transfer through the water removal. The concentrations observed are rather comparable to those found in wastewater.

Effective Monitoring of Fluxapyroxad and Its Three Biologically Active Metabolites in Vegetables, Fruits, and Cereals by Optimized QuEChERS Treatment Based on UPLC-MS/MS

Qualitative analysis and quantification of pesticide residues in foodstuff are essential to our health in daily life, especially regarding their metabolites, which may be more toxic and persistent. Thus, a valid analytical measure for detection of fluxapyroxad and its three metabolites (M700F002 (C-2), M700F008 (C-8), M700F048 (C-48)) in vegetables (cucumber, tomato, and pepper), fruits (grape, apple), and cereals (wheat, rice) was developed by UPLC-MS/MS with negative ion mode. The target compounds were extracted by acetonitrile contain 0.2% formic acid (v/v), and the extractions were cleaned up by octadecylsilane sorbents. The limits of quantitation and quantification were less than 0.14 μg kg^-1 and 0.47 μg kg^-1 in seven matrices. Furthermore, recoveries at levels of 0.01, 0.05, and 0.1 mg kg^-1 ranged from 74.9% to 110.5% with relative standard deviations ≤15.5% (n = 5). The method is validated to be effective and robust for the routine supervising of fluxapyroxad and its metabolites.

Behaviour of emerging contaminants in sewage sludge after anaerobic digestion

Nowadays, there is an increasing concern over the presence of contaminants in the aquatic environment, where they can be introduced from wastewater after their incomplete removal in the treatment plants. In this work, degradation of selected emerging pollutants in the aqueous and solid phases of sewage sludge has been investigated after anaerobic digestion using two different digesters: mesophilic and thermophilic. Initially, sludge samples were screened by ultra-high-performance liquid chromatography coupled to quadrupole time-of-flight mass spectrometry (UHPLC-QTOF MS) for identification of emerging contaminants in the samples. In a second step, a target quantitative method based on LC coupled to tandem MS was applied for selected pollutants identified in the previous screening. The behaviour of the compounds under anaerobic conditions was studied estimating the degradation efficiency and distribution of compounds between both sludge phases. Irbesartan and benzoylecgonine seemed to be notably degraded in both phases of the sludge. Venlafaxine showed a significant concentration decrease in the aqueous phase in parallel to an increase in the solid phase. The majority of the compounds showed an increase of their concentrations in both phases after the digestion. Concentrations in the solid phase were commonly higher than in the aqueous for most contaminants, indicating that they were preferentially adsorbed onto the solid particles.

Fate and behaviour of diclofenac during hydrothermal carbonization

Hydrothermal carbonization (HTC) has become an esteemed method to convert sewage sludge into biochar. Besides dewatering and disinfection the process is suggested to reduce the micropollutant load, which would be beneficial for the use of biochar as fertilizer. This study was designed to examine reduction of micropollutants and formation of transformation products during HTC using the example of diclofenac. We investigated compounds' removal at HTC conditions in inert experiments and in real samples. Results showed that HTC temperature (>190 °C) and pressure (∼15 bar) have the potential to fully degrade diclofenac in inert experiments and spiked sewage sludge (>99%) within 1 h. However, interfering effects hinder full removal in native samples resulting in 44% remaining diclofenac. Additionally, a combination of suspected-target and non-target analysis using LC-MS/MS and LC-HRMS resulted in the determination of six transformation products. These products have been reported in biochar from HTC for the first time, although other studies described them for other processes like advanced oxidation. Based on the detected transformation products, we proposed a degradation mechanism reflecting HTC reactions such as dehydroxylation and decarboxylation.

Validation of an Adapted QuEChERS Method for the Simultaneous Analysis of Polycyclic Aromatic Hydrocarbons, Polychlorinated Biphenyls and Organochlorine Pesticides in Sediment by Gas Chromatography-Mass Spectrometry

A Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) method has been adapted and validated for the simultaneous analysis of 16 PAHs, 12 PCBs and 9 OCPs in sediment. The sample preparation was adapted by modifying the nature of the extraction solvent, the extraction technique and the amount of sediment. The analytical performances were evaluated in terms of accuracy, linearity and quantification limits. The method was validated by the analysis of a reference marine sediment material (SRM 1941b). The obtained concentrations are in good agreement with the certified values with recoveries ranging 60 %-103 % for most of PAHs. Acceptable recoveries are obtained for PCBs, ranging 76 %-131 %, and for OCPs ranging 81 %-137 %. The method was applied to the analysis of sediments from the hydro-system Bizerte Lagoon/Ichkeul Lake (Tunisia). The Bizerte lagoon is mainly contaminated by PAHs whereas the Ichkeul lake is mainly by OCPs.

Analytical methodologies based on LC-MS/MS for monitoring selected emerging compounds in liquid and solid phases of the sewage sludge

In this work, two analytical methodologies based on liquid chromatography coupled to tandem mass spectrometry (LC–MS/MS) were developed for quantification of emerging pollutants identified in sewage sludge after a previous wide-scope screening. The target list included 13 emerging contaminants (EC): thiabendazole, acesulfame, fenofibric acid, valsartan, irbesartan, salicylic acid, diclofenac, carbamazepine, 4-aminoantipyrine (4-AA), 4-acetyl aminoantipyrine (4-AAA), 4-formyl aminoantipyrine (4-FAA), venlafaxine and benzoylecgonine. The aqueous and solid phases of the sewage sludge were analyzed making use of Solid-Phase Extraction (SPE) and UltraSonic Extraction (USE) for sample treatment, respectively. The methods were validated at three concentration levels: 0.2, 2 and 20 μg L⁻¹ for the aqueous phase, and 50, 500 and 2000 μg kg⁻¹ for the solid phase of the sludge. In general, the method was satisfactorily validated, showing good recoveries (70–120%) and precision (RSD < 20%). Regarding the limit of quantification (LOQ), it was below 0.1 μg L⁻¹ in the aqueous phase and below 50 μg kg⁻¹ in the solid phase for the majority of the analytes. The method applicability was tested by analysis of samples from a wider study on degradation of emerging pollutants in sewage sludge under anaerobic digestion.

The key benefits of these methodologies are:

• SPE and USE are appropriate sample procedures to extract selected emerging contaminants from the aqueous phase of the sewage sludge and the solid residue.

• LC–MS/MS is highly suitable for determining emerging contaminants in both sludge phases.

• Up to our knowledge, the main metabolites of dipyrone had not been studied before in sewage sludge.

Recent approaches for on-line analysis of residues and contaminants in food matrices: A review

This review highlights recent developments for on-line determination of residues and contaminants in complex matrices such as food samples. This involves the on-line coupling of a sample preparation technique (as the first "dimension") with a chromatographic system (second "dimension"), usually followed by mass spectrometry. Although frequently treated as quite distinct techniques, the role of all devices utilized as the first dimension in this approach aims to decrease the sample complexity while eliminating as much as possible the matrix contaminants to facilitate the qualitative and quantitative determination of the compounds of interest. This review will focus on the following techniques as the first dimension: (i) on-line solid-phase extraction; (ii) in-tube solid-phase microextraction; (iii) matrix solid-phase dispersion; and (iv) turbulent flow chromatography. The second dimension is usually performed using a chromatographic column to isolate the analyte(s) of interest for further mass spectrometry determination. A description of the basis of this on-line approach and its distinct set up possibilities is presented, which is followed by a critical review of the literature covering this subject in the last ten years (focusing on the last five years) with emphasis on the analysis of residue and contaminants in food samples.