Applications and factors influencing of the persulfate-based advanced oxidation processes for the remediation of groundwater and soil contaminated with organic compounds

Relying on the non-radical degradation of oxytetracycline by peroxymonosulfate activated with a magnetic Cu/Fe composite: performance and mechanism

CuFe-1 nanoparticles were successfully synthesized, and they could effectively activate peroxymonosulfate to assist the degradation of oxytetracycline.

Pyrene contaminated soil remediation using microwave/magnetite activated persulfate oxidation

Polycyclic aromatic hydrocarbons (PAHs) are important mutagen prevalent in the contaminated sites, bringing potential risks to human health. Iron oxides are important natural components in soils. Pyrene removal in soil using persulfate (PS) oxidation activated by microwave (MW) and magnetite (Fe₃O₄) was investigated. Fe₃O₄ significantly promoted pyrene removal in the soil; 91.7 % of pyrene was degraded within 45 min treatment. Pyrene removal rate in the Fe₃O₄/MW/PS system was 5.18 and 3.00 times higher than that in the Fe₃O₄/PS and MW/PS systems. Increasing in Fe₃O₄ dosage, PS concentration, MW temperature, and soil moisture content in the selected range were conducive for pyrene degradation. SO₄^•-, ^•OH, O₂^•-, and ¹O₂ were responsible for pyrene degradation, and the conversion of Fe (Ⅱ) in the Fe₃O₄ to Fe (Ⅲ) contributed to the formation of O₂^•- and ¹O₂. Characteristic bands of pyrene were more obviously destroyed by the Fe₃O₄/MW/PS oxidation, in comparison with MW/PS oxidation. Ring hydroxylation and ring-opening reactions were the main degradation pathways of pyrene. The toxicities of the formed byproducts were significantly reduced after treatment. This study provided a promising option for pyrene contaminated soil remediation.

A high-throughput and cost-effective microplate reader method for measuring persulfates (peroxydisulfate and peroxymonosulfate)

Frequent use of persulfates as oxidants, for in situ chemical oxidation and advanced oxidation processes, warrants the need for developing a fast and efficient method for measuring persulfate concentrations in aqueous samples in the lab and on site. Here, we propose a modified method, based on Liang et al.'s (2008) spectrophotometric method, for measuring both peroxydisulfate (PDS) and peroxymonosulfate (PMS) in the aqueous samples. Our method involves a deep 96-well plate, multi-channel pipettes, a small orbital shaker, and a microplate reader; allowing the preparation and analysis of up to 96 samples in one run. Our proposed method shortens the time by 10 folds, consumes only ∼2% of the original reagents, and generates only ∼2% of the liquid waste compared to the Liang et al.'s method, thus, making our method high-throughput, time-efficient, and cost-effective with reduced environmental impact. The presented microplate reader method is validated in terms of linearity, LOD, LOQ, accuracy, precision, robustness, and selectivity. All the parameters satisfied the acceptance criteria, according to ICH guidelines. The linearity of calibration curves was evaluated by performing the F-test. In general, our method has linear ranges from 20 to 42,000 and 5 to 40,960 μM for PDS and PMS, respectively. Accuracy (% recovery) results suggested that the LOD and LOQ based on the standard deviation of y-intercepts of the regression lines were the most reliable. The LOD/LOQ values for PDS and PMS were 14.7/44.1 and 4.6/14.4 μM, respectively. The proposed method was also modified to work with a standard cuvette spectrophotometer and was validated. A comparison with the UHPLC analysis of PDS showed that our microplate reader method performed equivalently or even outperformed the UHPLC method, in the presence of common groundwater constituents and organic contaminants.

Insights into carbon isotope fractionation on trichloroethene degradation in base activated persulfate process: The role of multiple reactive oxygen species

Understanding the role of reactive oxygen species (ROS) is essential to elucidate the mechanism of contaminants degradation in in-situ chemical oxidation (ISCO). In this study, compound specific isotope analysis (CSIA) and radicals quenching methods were integrated to investigate the roles of hydroxyl radical (HO), sulfate radical (SO₄^-), and superoxide radical (O₂^-) on trichloroethene (TCE) degradation during persulfate (PS) activated with base. The carbon isotope fractionation of TCE was found to be dependent of the base:PS ratios, yielding carbon enrichment factors (ε values) from -9.8 ± 0.5‰ to -16.7 ± 1.0‰ at base:PS molar ratios between 0.5:1 and 10:1, which was attributed to multi-pathways degradation of TCE by multiple ROS. The expected ε value (-31.6 ± 1.6‰) for TCE degradation via O₂^- attacking pathway, was more negative than those values via SO₄^- or HO pathways. The relative contributions of HO, SO₄^- and O₂^- for TCE degradation during base activated PS were estimated with observed ε values. HO and O₂^- were the predominant ROS for TCE degradation (with the relative contribution of 55-69% and 22-45%, respectively) in base activated PS. This work highlights the prospect of CSIA application for identifying degradation pathways of contaminants with ROS in environment.

Peracids - New oxidants in advanced oxidation processes: The use of peracetic acid, peroxymonosulfate, and persulfate salts in the removal of organic micropollutants of emerging concern - A review

In recent years, there has been increasing interest in using of advanced oxidation processes in water and wastewater decontamination. As a new oxidants peracids, mainly peracetic acid (PAA) and peracid salts, i.e. peroxymonosulfate (PMS) and persulfate (PS) are used. The degradation process of organic compounds takes place with the participation of radicals, including hydroxyl (^•OH) and sulfate (SO₄^•-) radicals derived from the peracids activation processes. Peracids can be activated in homogeneous systems (UV radiation, d-electron metal ions, e.g. Fe²⁺, Co²⁺, Mn²⁺, base, ozonolysis, thermolysis, radiolysis), or using heterogeneous activation (metals with zero oxidation state, metal oxides, quinones, activated carbon, semiconductors). As a result of oxidation, products of a lower mass than the parent compounds, less toxic, and more susceptible to biodegradation are formed. An important task is to investigate the effect of the peracid activation method and matrix composition on the efficiency of contamination removal. The article presents the latest information about the application of peracids in the removal of organic micropollutants of emerging concern (mainly focuses on endocrine disrupted compounds). The most important information on peracetic acid, peroxymonosulfate and persulfate salts, and methods of their activation are presented. Current uses of these oxidants in organic micropollutants removal are also described. Information was collected on the factors influencing the oxidation process and the effectiveness of pollutant removal. This paper compares PAA, PMS and PS-based processes for the first time in terms of kinetics and efficiency.

Development of a hydroxyl group-mediated biosynthetic schwertmannite as a persulfate activator for efficient degradation of RhB and Cr(VI) removal

Recently, sulfate radical-based advanced oxidation processes (SR-AOPs) have shown broad potential for restoring the water environment. However, the application of SR-AOPs to simultaneously remove organic pollutants and Cr(VI) has rarely been reported. Herein, we developed a modified schwertmannite (Sch-PVA) synthesized via the mediation of Acidithiobacillus ferrooxidans in the introduction of polyvinyl alcohol (PVA). This modification significantly changed the morphology and structure of the schwertmannite (Sch). The specific surface area and the density of functional sites also increased. Sch-PVA significantly increased the persulfate (PDS) activation efficiency. Even in 100 mg L^-1 rhodamine B (RhB) conditions, 96.3% of RhB was eliminated by 0.5 g L^-1Sch-PVA and 6 mM PDS in 120 min. Moreover, excellent performance was exhibited over a wide pH range. The dissolution of the passivation layer facilitated the exposure of new adsorption and reduction sites, thereby enhancing the simultaneous removal of RhB and Cr(VI). Quenching experiments and electron spin resonance (ESR) measurements verified that sulfate and hydroxyl radicals were generated. The hydroxyl groups on the Sch-PVA surface played a key role in the bonding with and the activation of PDS. In conclusion, Sch-PVA provides new insights into the catalyst application for simultaneous removal of organic pollutants and Cr(VI).

Study on influence factors of treating landfill leachate by ultraviolet-activated persulfate system

In recent years, there have been many studies on treating pollutants with ultraviolet-activated persulfate (UV/PDS) system. In this paper, the biochemical treatment effluent of landfill leachate from garbage incineration power plant was treated. The effect of treating landfill leachate with UV/PDS system in the low-pressure external device and medium-pressure built-in device was compared; it was concluded that in the latter device, the photon quantity increased, the energy loss decreased, and the probability of generating free radicals in the reaction between photons and S₂O₈^2- increased, which result the treatment efficiency of this system was higher. In addition, the leachate was treated by combining the activation method of spinel composite (CuO-MgAl₂O₄) with UV activation method, called CuO-MgAl₂O₄/UV/PDS. The experimental data showed that the processing effect of segmented dosing PDS process was higher than that of one-time addition process. Under the same conditions, the removal rates of CODcr were 83.10% and 19.76%, respectively. One of the reasons for this result may be that excessive PDS in CuO-MgAl₂O₄/PDS system of the latter process inhibited the treatment effect. This paper analyzes the efficiency of UV/PDS system, as well as CuO-MgAl₂O₄/UV/PDS combination process which were used to treat landfill leachate under different conditions; the results showed that the medium-pressure built-in device and segmented-dosing process could get better treatment effect.

A review on percarbonate-based advanced oxidation processes for remediation of organic compounds in water

Sodium percarbonate (SPC) is considered a potential alternative to liquid hydrogen peroxide (H₂O₂) in organic compounds contaminated water/soil remediation due to its regularly, transportable, economical, and eco-friendly features. The solid state of SPC makes it more suitable to remediate actual soil and water with a milder H₂O₂ release rate. Apart from its good oxidative capacity, alkaline SPC can simultaneously remediate acidized solution and soil to the neutral condition. Conventionally, percarbonate-based advanced oxidation process (P-AOPs) system proceed through the catalysis under ultraviolet ray, transition metal ions (i.e., Fe²⁺, Fe³⁺, and V⁴⁺), and nanoscale zero-valent metals (iron, zinc, copper, and nickel). The hydroxyl radical (^•OH), superoxide radical (^•O₂^-), and carbonate radical anion (^•CO₃^-) generated from sodium percarbonate could attack the organic pollutant structure. In this review, we present the advances of P-AOPs in heterogeneous and homogeneous catalytic processes through a wide range of activation methods. This review aims to give an overview of the catalysis and application of P-AOPs for emerging contaminants degradation and act as a guideline of the field advances. Various activation methods of percarbonate are summarized, and the influence factors in the solution matrix such as pH, anions, and cations are thoroughly discussed. Moreover, this review helps to clarify the advantages and shortcomings of P-AOPs in current scientific progress and guide the future practical direction of P-AOPs in sustainable carbon catalysis and green chemistry.

Transformation of ammonium to nitrophenolic byproducts by sulfate radical oxidation

Sulfate radical (SO₄^•-) based oxidation shows great promise in wastewater treatment and subsurface remediation. For the first time, we demonstrated that SO₄^•- could induce the transformation of ammonium (NH₄⁺) to nitrophenolic byproducts. Using high-resolution mass spectrometry in combination with ¹⁵N labeling, mono-nitro and di-nitro phenolic byproducts were identified in a sample containing 1 mM NH₄⁺ and 10 mg/L natural organic matter (NOM) following heat activated peroxydisulfate (PDS) oxidation. At PDS dose of 1 mM, the formation of p-nitrophenol and 5-nitrosalicylic acid reached 0.21 and 0.30 μM, respectively, in 12 h and then decreased; the formation of 2,4-dinitrophenol and 3,5-dinitrosalicylic acid increased monotonically, reaching 0.37 and 0.62 μM, respectively, in 24 h. One-electron oxidation of NH₄⁺ to form aminyl radicals (^•NH₂) was the first step of the transformation. The reaction of ^•NH₂ with oxygen was a key step in propagating radical chain reactions, leading to nitrogen dioxide radicals (NO₂^•) as a key nitrating agent. The reactive sites susceptible to nitrating in NOM molecules are not limited to phenolic moieties. We found that aromatic carboxylate moieties could be in situ transformed to phenolics by SO₄^•-, thus contributed to nitrophenolic byproducts formation as well. Considering the ubiquitous presence of NH₄⁺ in the environment, formation of nitrophenolic byproducts will be widespread when SO₄^•- is applied for onsite remediation, which should be taken into consideration when evaluating the feasibility of this technology.

Efficiency and Quantitative Structure-Activity Relationship of Monoaromatics Oxidation by Quinone-Activated Persulfate

Quinones and quinone-containing organics have potential of activating persulfate to produce sulfate radical. In this work, the optimal condition for quinone activation of persulfate was investigated. It was found representative monoaromatics were degraded fastest in alkaline environment (pH 10.0), but excessive alkalinity restrained the reaction instead. The mechanisms to explain this phenomenon were speculated. The effect of initial quinone concentration on persulfate oxidation was also investigated at pH 10.0. In addition, a quantitative structure-activity relationship model was established with 15 kinds of monoaromatics, which revealed the most negative atomic net charges on carbon atom played an important role on degradation rates. Chemicals with a smallerq C - were easier oxidized in quinone-activate system. This finding helps further exploration of effective activator in alkaline environment.

Ubiquitous Production of Organosulfates During Treatment of Organic Contaminants with Sulfate Radicals

Oxidation of organic contaminants by sulfate radical (SO₄ ^•-) is becoming more popular for the treatment of hazardous waste sites by in situ chemical oxidation (ISCO) and industrial wastewater by advanced oxidation processes (AOPs). It is well documented that SO₄ ^•- can produce similar oxygen-containing transformation products as hydroxyl radical-based treatment processes, but SO₄ ^•- also has the potential to produce organosulfates by radical addition. Experiments conducted with a suite of 23 aromatic and 5 aliphatic compounds, including several contaminants typically detected at hazardous waste sites, demonstrated the formation of at least one stable sulfate-containing product for 25 of the compounds. These compounds likely exhibit higher mobility in the subsurface due to a lower affinity for surfaces (e.g., aquifer solids, activated carbon) than most other transformation products. Although the health risks associated with organosulfates are still uncertain, some aromatic organosulfates produced in this study (i.e. phenyl sulfate and p-cresyl sulfate) are known to be harmful uremic toxins. Further study of organosulfate formation, fate, and toxicity is needed before SO₄ ^•--based treatment processes are more widely employed.

Application of choline-based deep eutectic solvent for the extraction of crude-oil contaminated soils

Choline-based deep eutectic solvents (DESs) have many outstanding features as they are easy to prepare, inexpensive, low-toxic, low volatile, and biodegradable, which make them increasingly attractive in industrial chemistry and green chemistry. In this paper, the abilities of three different kinds of DESs for crude oil removal from contaminated soils were compared and it was found the DES formed by phenylpropionic acid and choline chloride (mole ratio = 2:1) had the best performance. The effects of extraction time, temperature and the solvent-soil ratio on phenylpropionic acid/choline chloride DES performance were evaluated. The rational extraction conditions were recommended as follows: mass ratio of DES to soil was 10:1 and 60 min extraction time at 80°C. The extraction (desorption) process could be described by Freundlich desorption isotherm mode. In addition, the phenylpropionic acid/choline chloride DES could be recycled and the oil removal efficiency was about 90% after 10 cycles. This finding suggested that choline-based DES extraction was a promising technology for crude oil removal from contaminated soil.

Interrelated effects of soils and compounds on persulfate oxidation of petroleum hydrocarbons in soils

Persulfate-based chemical oxidation of petroleum hydrocarbons (TPHs) in soils usually varies drastically with soil sites. Complex effects of soil components on persulfate oxidation of TPHs remains poorly understood, impeding the understanding of persulfate oxidation in practical systems. Here we provided empirical evidence for the interrelated effects of natural soils components and target TPHs on persulfate oxidation of TPHs. Inputs of TPHs led to notable alterations of organic matter, minerals and pH of soils, which in turn influenced distributions and availability of TPHs in soils. These soil/TPH properties and oxidant dose constituted five interrelated terms that were used to develop a predictive model of persulfate oxidation of TPHs. Such interrelation accounted for ilmenite-base coupling activation of persulfate oxidation, Fe/Mn mineral activation of persulfate oxidation, chemical oxidant demand of soils, mass transfer-reactivity limiting of TPHs, and applicable parameters of persulfate oxidation, respectively. The interrelation-based model of persulfate oxidation of TPHs displayed high predictive accuracy of 43% for a factor of 0.3 above and below the ideal fit, despite large differences in contaminated sites and applicable parameters. This finding may have practical interests in the optimization of persulfate oxidation.

A coupled optimization of groundwater remediation alternatives screening under health risk assessment: An application to a petroleum-contaminated site in a typical cold industrial region in Northeastern China

Contaminated sites have been recognized as posing serious comprehensive social and environmental issues and have earned worldwide attention. China is becoming one of the largest contaminated sites remediation markets in the world and the contaminated sites in northeastern China need to rehabilitate urgently. However, remediation planning is often hindered by high financial costs resulting from incomplete assessments of pollution and inappropriate remediation plans. In-depth contaminated site assessments can provide the necessary baseline data for remediation alternatives screening. Therefore, risk assessments and remediation decisions will play crucial roles in the rehabilitation and reconstruction of contaminated sites in China. The main objectives of this study were to present a novel method for health risk assessment (HRA) and to demonstrate a multicriteria decision analysis (MCDA) based on this method to select the most suitable remediation alternatives of groundwater and to prioritize management of contaminated site. To demonstrate the HRA and MCDA processes, a typical contaminated site in Longtan, Jilin province, China, was used. The results of this research indicated that Benzene (PhH) and 1,2-Dichloroethylene (1,2-DCE) were the main organic pollutants and the vanillin plant in the north of the site was main pollution source. Pollution migrated from the north to the south and the health risk range in winter was significantly greater than in summer. Four remediation alternatives were proposed on the basis of the HRA results. The MCDA results showed that PRB was the most suitable technology for integrating the relevant environmental, social, economic, and technical aspects required for remediation. This study may help responsible agencies to strengthen local risk-based program screening frameworks for contaminated sites, to promote reconstruction projects, and to increase local public confidence of contaminated sites remediation.

The oxidative stress caused by atrazine in root exudation of Pennisetum americanum (L.) K. Schum

Pearl millet (Pennisetum americanum (L.) K. Schum) has been proven as a potential remediation plant of the pollution caused by atrazine. Plants used in remediation can release root exudates to communicate with rhizosphere microorganisms and accelerate the removal of pollutants in soil. However, the response of pearl millet root exudates under atrazine stress has remained unclear. In this study, hydroponic experiments were conducted at Northeast Agricultural University, Harbin, China, to investigate the oxidative stress response and the changes in composition of root exudates in pearl millet plants that were exposed to 19.4 mgL^-1 of atrazine, compared to the untreated control. The experiment was established as six treatments with exposure to no atrazine for 2, 4 and 6 days (CK-2, CK-4, CK-6) and 19.4 mgL^-1 atrazine for 2, 4 and 6 days (AT-2, AT-4, AT-6), respectively. The results suggest that the growth of the seedlings changed slightly when exposed to atrazine for 2 days. The content of thiobarbituric acid reactive substances exposed to atrazine for 6 days increased 26% compared with the treatment that was exposed for 2 days. Moreover, the reactive oxygen species in test plant obviously increased when exposed to atrazine for 6 days. In addition, the activity of superoxide dismutase increased from 30.82 ug^-1 to 37.33 ug^-1 fresh weight after 6 days of exposure to atrazine. The results of a nontargeted metabolomic analysis suggest that carbohydrate metabolism, fatty acid metabolism and amino acid metabolism in pearl millet were obviously affected by the oxidative stress caused by atrazine. The contents of sphinganine and methylimidazole acetaldehyde in CK-6 increased by 5.14 times and 2.05 times, respectively, compared with those of CK-2. Furthermore, the contents of (S)-methylmalonic acid semialdehyde and 1-pyrroline-2-carboxylic acid decreased by 0.56 times and 0.5 times, respectively, compared with the AT-6. These results strongly suggest that the changes observed in the composition of root exudates in pearl millet seedlings can be attributed to the oxidative stress caused by atrazine.

Manganese ferrite modified biochar from vinasse for enhanced adsorption of levofloxacin: Effects and mechanisms

The primitive biochar (BC) and NiFe₂O₄/biochar composites (NFBC), biological adsorbents prepared from vinasse wastes, possess the environmental application in levofloxacin (LEV) removal. In this study, the efficient adsorption of LEV onto biochar synthesized by pyrolysis of vinasse wastes from aqueous environment was investigated. The influencing factors (i.e., pH, reaction time, and temperature) of adsorption process were also well studied. The results indicated that the maximum adsorption capacities of both BC and NFBC were occurred in mildly acidic condition (pH 6). In addition, the biochar adsorption capacities were obviously increased in higher temperature (25-45 °C). The chemistry adsorption and monolayer homogeneous dominated adsorption process of LEV onto BC and NFBC. The adsorption process was spontaneous and endothermic by thermodynamic analysis. The SEDA (site energy distribution analysis) explained that the adsorption effectivity increased by increasing site energy of biochar surface. The SEDA revealed the more energy heterogeneity in NFBC, fitting the characterization result of Fourier-transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The electron-donor-acceptor (EDA) interactions and hydrogen bonds is suggested as the major adsorption mechanism. And as for the adsorption of the various biowaste recycled synthetic, this study can be referred in discussion of performance analysis and optimal condition.

In-depth investigation of Sodium percarbonate as oxidant of PAHs from soil contaminated with diesel oil

Sodium percarbonate (SPC, 2Na₂CO₃∙3H₂O₂), is a compound that can be used under multiple environmental applications. In this work, SPC was employed as oxidant in the treatment of soil contaminated with diesel oil. The soil samples were collected during the earthmoving stage of RNEST Oil Refinery (Petrobras), Brazil. Then, the samples were air-dried, mixed and characterized. Subsequently, raw soil was contaminated with diesel and treated by photo-Fenton reaction (H₂O₂/Fe²⁺/UV). SPC played a significant role in the generation of hydroxyl radicals under the catalytic effect of ferrous ions (Fe²⁺), hydrogen peroxide (H₂O₂) and radiation. These radicals provoked the photodegradation of polycyclic aromatic hydrocarbons (PAHs), in the soil remediation. A factorial design 3³ was carried out to assess the variables which most influenced the decrease in total organic carbon (TOC). The study was performed with the following variables: initial concentration of [H₂O₂] and [Fe²⁺], between 190.0 and 950.0 mmol L^-1 and 0.0-14.4 mmol L^-1, respectively. UV radiation was supplied from sunlight, blacklight lamps, and system without radiation. All experiments were performed with 5.0 g of contaminated soil in 50.0 mL of solution. The initial concentration of Fe²⁺ showed the statistically most significant effect. The oxidation efficiency evaluated in the best condition showed a decrease from 34,765 mg kg^-1 to 15,801 mg kg^-1 in TOC and from 85.750 mg kg^-1 to 20.770 mg kg^-1 in PAHs content. Moreover, the sums of low and high molecular weight polycyclic aromatic hydrocarbons (LMW-PAHs and HMW-PAHs) were 19.537 mg kg^-1 and 1.233 mg kg^-1, respectively. Both values are within the limits recommended by the United Sates Environmental Protection Agency (USEPA) and evidenced the satisfactory removal of PAHs from contaminated soil, being an alternative to classic oxidation protocols.

Rapid removal of organic pollutants by a novel persulfate/brochantite system: Mechanism and implication

Using natural minerals as persulfate activators can develop effective and economical in situ chemical oxidation technology for environmental remediation. Yet, few natural minerals can provide a high activation efficiency. Here, we demonstrate that brochantite (Cu₄SO₄(OH)₆), a natural mineral, can be used as a persulfate activator for the rapid degradation of tetracycline hydrochloride (TC-H). Approximately 70% of TC-H was removed in Cu₄SO₄(OH)₆/PDS within 5 min, which much higher than that of Cu₃P (61.99%), CuO (29.75%), CNT (25.83%), Fe₂O₃, (14.48%) and MnO₂ (9.76%). Experiments and theoretical calculations suggested that surface copper acts as active sites induce the production of free radicals. The synergistic effect of Cu/S promotes the cycle between Cu⁺/Cu²⁺. Sulfate radicals and hydroxyl radicals are the main reactive oxygen species that are responsible for the rapid removal of TC-H. The findings of this work show a novel persulfate/brochantite system and provide useful information for the environmental remediation.

Degradation of Atrazine, Simazine and Ametryn in an arable soil using thermal-activated persulfate oxidation process: Optimization, kinetics, and degradation pathway

This study examined the feasibility of applying thermal-activated persulfate (PS) oxidation for remediation of soil co-contaminated with s-triazine herbicides including Atrazine (ATZ), Simazine (SIM) and Ametryn (AME). Homogeneous activation using heating method (50 °C) was selected. Results showed that thermal-activated PS oxidation process may successfully degrade ATZ in soil and degradation efficiency was increased along the arising activation temperature. Higher PS dosages and depressed initial pH were beneficial for degradation while increasing initial ATZ concentration may hamper the degradation. The oxidation process may lead to changes of surface functional groups on soil. The presence of Cl^-, HCO₃^- and H₂PO₄^- at both of low and high concentrations may inhibit the degradation of ATZ. Soil depths may apparently influence the ATZ degradation which followed 0-10 < 10-30 < 30-60 cm mainly depending on the soil organic matter (SOM) contents. Thermal-activated PS may effectively degrade ATZ, SIM and AME under co-contaminated condition and the more favorable of ethyl group towards SO₄^- than isopropyl and methylation groups was detected. Both of SO₄^- and HO were identified to be responsible for degradation. Finally, degradation intermediates of ATZ, SIM and AME were identified by LC-Q-TOF-MS and detailed transformation pathways for three pesticides were proposed, respectively.

Improving solid-liquid separation performance of anaerobic digestate from food waste by thermally activated persulfate oxidation

Anaerobic digestion is a promising ecofriendly technology for the management of the continuous increasing food waste (FW). However, the large amount of resulting anaerobic digestate are very difficult to be purified due to high concentration of suspended colloids. Solid-liquid separation is a pivotal step for the subsequent biological treatment of the digestate by activated sludge process. The dewaterability of digestate could directly reflect the solid-liquid separation performance. In this study, a thermally-activated persulfate (PDS) conditioning method was utilized to enhance the digestate dewaterability. Results revealed that PDS thermally conditioning significantly improved the dewaterability by decreasing digestate pH and decomposing organic substances in digestate. The decline of pH, which was resulted from PDS thermally activation reaction, facilitated filterability improvement via reducing the surface negative charges and prompting the oxidizing ability of PDS-relevant radicals. Protein, the main organic component in digestate, was most closely correlated with digestate dewaterability. Fortunately, they were also the most vulnerable constituent under the oxidation attack. PDS thermal conditioning at 80°C was proven to be the most suitable for improving the solid-liquid separation performance of anaerobic. For practical application in conditioning the anaerobic digestate from FW, the conditions should be further optimized according to the digestate characteristic.

Impact of application of heat-activated persulfate oxidation treated erythromycin fermentation residue as a soil amendment: Soil chemical properties and antibiotic resistance

Erythromycin fermentation residue (EFR) is the precipitation of fermentative biowaste used for extracting erythromycin (ERY) and may be disposed via land application after heat-activated persulfate (PS) oxidation treatment. However, the effects of the treated EFR as a soil amendment on soil chemical properties and the potential resistance risks caused by introduced ERY remain unclear. Here, a laboratory soil incubation experiment was performed to investigate the soil pH, salinity, introduced antibiotics, antibiotic resistance genes (ARGs) and mobile genetic elements (MGEs), as well as bacterial community structure in the treated EFR-amended soil. The results indicated that pH in treated EFR-amended soil decreased firstly and then increased. The salinity of soil increased but soil was still non-saline soil. In addition, the introduced ERY in the treated EFR-amended soil decreased with the half-life of 12.3 d. Moreover, the relative abundances of ERY resistance genes and MGEs in the treated EFR-amended soil were much lower than those in the control at the end of incubation. Bacterial community structure in the treated EFR-amended soil converged to similar structure in control soil after 49 d incubation. Our results showed that heat-activated PS oxidation treatment of EFR prior to application to soil might be in favor of limiting the spread of ERY resistance genes and MGEs.

Efficient removal of triclosan via peroxymonosulfate activated by a ppb level dosage of Co(II) in water: Reaction kinetics, mechanisms and detoxification

Triclosan (TCS), an extensively used broad-spectrum antimicrobial agent, has raised significant environmental concerns regarding its widespread occurrence in waters. In this study, the removal of TCS in aqueous solution via peroxymonosulfate (PMS) activated by an extremely low-level Co²⁺ (0.02 μM) was systematically investigated. During preliminary test, TCS (10 μM) was totally degraded in 30 min by using 0.1 μM Co²⁺ and 40 μM PMS at pH 7.0 with a degradation rate constant of 0.1219 min^-1. A first-order apparent degradation rate of TCS was found with respect to the PMS concentrations. At extremely low dosage of Co²⁺ (0.02 μM), the presence of NO₃^-, HCO₃^-, PLFA, and SRHA within test concentrations significantly inhibited TCS removal, while a dual effect of Cl^- on the degradation rate of TCS was observed. The quenching experiments verified that SO₄^- was the dominant reactive oxygen species (ROS) rather than OH. Six major intermediates were identified using TOF-LC-MS, based on which we proposed three associated reaction pathways including hydroxylation, ether bond breakage, and dechlorination. Toxicity predictions by ECOSAR software exhibited aquatic toxicity reduction of TCS after Co²⁺/PMS treatment. We outlook these findings to advance the feasibility of organic contaminants removal via Co²⁺/PMS system with Co²⁺ at extremely low levels.

Highly nitrogen-doped porous carbon transformed from graphitic carbon nitride for efficient metal-free catalysis

Nitrogen-doped carbon materials are proposed as promising metal-free catalysts for persulfate-mediated catalytic oxidation process, yet the nitrogen content in the final carbon products is typically low. Moreover, controversies remain in the unambiguous identification of active sites in nitrogen-doped carbons for persulfate activation. Here we report the facile synthesis of nitrogen-doped carbon material via one-step pyrolysis of urea and D-mannitol, which simultaneously combine ultrahigh nitrogen content (up to 33.75 at%) with apparent porous structure via transformation from graphitic carbon nitride. With this strategy, the highly nitrogen-doped porous carbon (NC_1.0) exhibits excellent catalytic activity toward peroxymonosulfate (PMS) activation for oxidation of organic pollutants. Both experiments and density functional theory (DFT) calculations, for the first time, revealed that the electron-rich graphitic N and electron-deficient carbon atom adjacent to graphitic N in NC_1.0 served as active sites for PMS reduction and oxidation toward the generation of hydroxyl radical (OH) and singlet oxygen (¹O₂), respectively, in which PMS oxidation was the main reaction in the course of PMS activation rendering ¹O₂ the dominant reactive oxygen species (ROS) in the NC_1.0/PMS system. More importantly, NC_1.0 presents robust stability in PMS activation, superior to most reported nitrogen-doped carbon-based catalysts, offering great promise for practical environmental remediation.

Formation of chloronitrophenols upon sulfate radical-based oxidation of 2-chlorophenol in the presence of nitrite

Sulfate radical (SO₄^-)-based advanced oxidation processes (SR-AOPs) are promising in-situ chemical oxidation technologies widely applied for soil/groundwater remediation. The presence of non-target water constituents may interfere the abatement of contaminants by SR-AOPs as well as result in the formation of unintended byproducts. Herein, we reported the formation of toxic chloronitrophenols during thermally activated persulfate oxidation of 2-chlorophenol (2CP) in the presence of nitrite (NO₂^-). 2-Chloro-4-nitrophenol (2C4NP) and 2-chloro-6-nitrophenol (2C6NP) were identified as nitrated byproducts of 2CP with total yield up to 90%. The formation of nitrated byproducts is a result of coupling reaction between 2CP phenoxyl radical (ClPhO) and nitrogen dioxide radical (NO₂). As a critical step, the formation of ClPhO was supported by density functional theory (DFT) computation. Both 2C4NP and 2C6NP could convert to 2-chloro-4,6-dinitrophenol (2C46DNP) upon further treatment via a denitration-renitration process. The formation rate of 2C4NP and 2C6NP was closely dependent on the concentration of NO₂^-, solution pH, and natural water constituents. ECOSAR calculation suggests that chloronitrophenols are generally more hydrophobic and ecotoxic than 2CP. Our result therefore reveals the potential risks in the abatement of chlorophenols by SR-AOP, particularly when high level of NO₂^- is present in water matrix.

AOPs-based remediation of petroleum hydrocarbons-contaminated soils: Efficiency, influencing factors and environmental impacts

Petroleum hydrocarbons are a class of anthropogenic compounds including alkanes, aromatic hydrocarbons, resins, asphaltenes and other organic matters, and soil pollution caused by petroleum hydrocarbons has drawn increasing interest in recent years. Multiple advanced oxidation processes (AOPs) are emerging to remediate petroleum hydrocarbons-contaminated soils, while very few studies have focused on the features of AOPs applied in soils. This review aims to provide an updated overview of the state of the science about the efficiency, influencing factors and environmental implications of AOPs. The key findings from this review include: 1) cyclodextrin and its derivatives can be used to synthesize targeting reagents; 2) soil organic matter (SOM), glucose and cement can activate persulfate; 3) SOM affects redox circumstance in soil and could be further developed for enhancing the catalysis effect of transition metals; 4) non-thermal plasma and wet oxidation are promising methods of AOPs to remove petroleum hydrocarbons from soil; 5) the occurrence, fate, and transformation of intermediates during the degradation of petroleum hydrocarbons in soil should be considered more. Overall, this review reveals an urgent need to develop the cost-effective remedial strategies for petroleum hydrocarbons contaminated soils, and to advance our knowledge on the generation, transport and propagation of radicals in soils.

Fabrication of sustainable manganese ferrite modified biochar from vinasse for enhanced adsorption of fluoroquinolone antibiotics: Effects and mechanisms

An effective adsorbent towards fluoroquinolone antibiotics was synthesized via a facile two-step approach, the co-precipitation of Fe, Mn with vinasse wastes and then pyrolysis under controlled conditions which denoted as FMB. Its adsorption behavior was examined based on a batch adsorption experiment of fluoroquinolone antibiotics pefloxacin (PEF) and ciprofloxacin (CIP). Experimental factors, such as pH, adsorbent dose, ionic strength, contact time and temperature have done a great deal to influence the adsorption of PEF and CIP. The FMB demonstrated excellent performance in reusability tests towards to both PEF and CIP, which showed that the recycling efficiency of PEF and CIP could remain ~55% and ~80% after five recycle cycles, respectively. The dominated adsorption mechanisms included pore filling effect, π-π stacking interaction, π-π EDA, hydrogen bonding and hydrophobicity. Overall, this work presented FMB was recognized as an effective, environmental-friendly and magnetically separable adsorbent for alleviating fluoroquinolone antibiotics contamination from water.

Removal of polycyclic aromatic hydrocarbons (PAHs) and the response of indigenous bacteria in highly contaminated aged soil after persulfate oxidation

Integrated chemical-biological treatment is a promising alternative to remove PAHs from contaminated soil, wherein indigenous bacteria is the key factor for the biodegradation of residual PAHs after the application of chemical oxidation. However, systematical study on the impact of persulfate (PS) oxidation on indigenous bacteria as well as PAHs removal is still scarce. In this study, the influences of different PS dosages (1%, 3%, 6%, and 10% [w/w]), as well as various activation methods (native iron, H₂O₂, alkaline, ferrous iron, and heat) on PAHs removal and indigenous bacteria in highly contaminated aged soil were investigated. Apparent degradation of PAHs in the soil treated with PS oxidation was observed, and the removal efficiency of total PAHs in the soil ranged from 38.28% to 79.97%. The removal efficiency of total PAHs in the soil increased with increasing consumption of PS. However, the bacterial abundance in soil was negatively affected following oxidation for all of the treatments added with PS, with bacterial abundance in the soil decreased by 0.89-2.93 orders of magnitude compared to the untreated soil. Moreover, the number of total bacteria in the soil decreased as PS consumption increased. Different PS activation methods and PS dosages exhibited different influences on the bacterial community composition. Bacteria capable of degrading PAHs under anoxic conditions were composed predominantly by Proteobacteria and Firmicutes. The total amount of Proteobacteria and Firmicutes also decreased with increasing consumption of PS. The results of this study provide important insight for the design of PAHs contaminated soil remediation projects.

In-situ self-assembly of robust Fe (III)-carboxyl functionalized polyacrylonitrile polymeric bead catalyst for efficient photo-Fenton oxidation of p-nitrophenol

From the view of channel confinement and functional site capture, we develop an in-situ self-assembly strategy to fabricate the carboxyl functionalized Fe-HPAN bead catalyst with highly stable and uniformly dispersed metallic sites for efficient photo-Fenton oxidation of p-nitrophenol (p-NP). BET and FTIR analysis reveal that numerous carboxyl groups and mesopores exist in Fe-HPAN beads, which acts to capture and immobilize iron ions. Catalytic results show that the degradation rate and TOC removal for p-NP were up to 99.78 and 91.68% under the optimal condition. Even at near neutral pH, the degradation rate almost keep the same and the TOC removal can still reach 73.05%. Due to the autocatalytic cycle of Fe^III/Fe^II, the apparent rate constant of Fe-HPAN (0.2247 min^-1) was 5.4 times as high as unmodified Fe-PAN (0.0415 min^-1) in the presence of H₂O₂ and visible light irradiation, which was 2-3 orders of magnitude larger than that of other reaction systems. More importantly, Fe-HPAN bead catalyst exhibited little loss of activity even after 20 cycles of re-utilization. The possible degradation pathway of p-NP was also proposed based on GC/MS analysis. The present work may provide a new perspective for the use of synthetic polymer to prepare low-cost, efficient and robust photo-Fenton oxidation catalysts.

A new insight into adsorption state and mechanism of adsorbates in porous materials

An in situ freeze method (in liquid N₂) is developed to study the adsorption behaviours of volatile organic compounds (VOCs). Using the proposed method, the adsorption state and adsorption mechanism of adsorbates (pore filling effect or mono/multilayer stacking) in pores of adsorbent can be perceived clearly. We can also acquire the contribution rate of each pore to adsorption capacity. It is found that for toluene adsorption, more pores smaller than around 1.1 nm should be made in activated carbon if it's below 100 ppm, while more pores of around 1.2-5 nm should be made if it's beyond 1000 ppm. This measurement method presents a more comprehensive description on the adsorption state of VOCs in micro- and mesopores, extending the development of adsorbent design and adsorption mechanism in chemical and environmental engineering.

A sustainable ferromanganese biochar adsorbent for effective levofloxacin removal from aqueous medium

This present study reported the synthesis and characterization of a low-cost, environment friendly and high efficient biochar, ferromanganese modified biochar (Fe/Mn-BC) for the removal of levofloxacin (LEV) from aqueous medium. Fe/Mn-BC was synthesized through the facile co-precipitation of Fe, Mn with vinasse wastes and then pyrolysis under controlled conditions. The characterization of Fe/MnBC was analyzed by scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray diffraction patterns (XPS), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Raman. Some influencing factors (e.g., pH, Fe/Mn-BC dosage, initial LEV concentration, ionic strength, contact time and temperature) were comprehensively investigated. The results manifested that the adsorption process of LEV onto Fe/Mn-BC was high pH dependence and the maximum adsorption capacity was achieved at pH 5. Moreover, the adsorption capacity of LEV was increased with increasing ionic strength. To gain a clearer perspective on the adsorption behavior of LEV onto Fe/Mn-BC, the adsorption kinetics and isotherms were also performed, revealing pseudo-second-order and Freundlich model had a better fitting effect. Reusability experiments indicated that Fe/Mn-BC could maintain a certain adsorption capacity for LEV after 5 recycles. Overall, this work showed that Fe/Mn-BC was an effective and promising adsorbent for eliminating LEV from aqueous medium.

Precise control of iron activating persulfate by current generation in an electrochemical membrane reactor

Activated persulfate (PS) oxidation is promising for contaminant removal but a lack of controllable activation can lead to a loss of reagents and thus low contamination degradation. Herein, we have proposed and investigated an innovative method to control PS activation by introducing ion exchange membrane into electrochemically activated PS. This electrochemical membrane reactor (EMR) could precisely control PS activation by adjusting electrical current for slow release of Fe²⁺, and also avoid direct contact between PS and a sacrificial anode electrode (iron electrode)/an alkaline cathode solution. It was found that the PS decomposition rate constant was linearly increased by increasing the applied current (R² = 0.988). The rate of the released Fe²⁺ also exhibited a linear relationship with the applied current (R² = 0.995). Compared to one-time dosage of Fe²⁺, the EMR-based slow-release process had higher contamination degradation and better PS utilization (molar ratio of the decomposed PS to the migrated Fe, 1.04 ± 0.01:1), thereby minimizing the waste of both reaction reagents and generated radicals. The EMR was also employed to degrade a representative dye contaminant in a controllable manner and achieved 95.7 ± 0.7% removal percentage with PS dosage of 3.0 g L^-1 within 20 min. This study is among the earliest to explore effective approaches for precisely controlling PS activation and subsequent oxidation of contaminants.

Physico-chemical processes

The review scans research articles published in 2018 on physico-chemical processes for water and wastewater treatment. The paper includes eight sections, that is, membrane technology, granular filtration, flotation, adsorption, coagulation/flocculation, capacitive deionization, ion exchange, and oxidation. The membrane technology section further divides into six parts, including microfiltration, ultrafiltration, nanofiltration, reverse osmosis/forward osmosis, and membrane distillation. PRACTITIONER POINTS: Totally 266 articles on water and wastewater treatment have been scanned; The review is sectioned into 8 major parts;  Membrane technology has drawn the widest attention from the research community.

Wood-based biochar as an excellent activator of peroxydisulfate for Acid Orange 7 decolorization

Wood-based biochar, as a metal-free heterogeneous activator of peroxydisulfate (PDS), was successfully prepared by pyrolysis of polar sawdust for efficient removal of Acid Orange 7 (AO7). The results demonstrate PDS could be effectively activated by wood-based biochar, and AO7 was rapidly eliminated in a wide range of pH value (3.0-10.0) with AO7 removal achieved ≥ 99.3% after 14 min reaction. The dominant reactive species in the biochar/PDS system were verified via radical quenching tests and electron paramagnetic resonance (EPR) technique. It is speculated that sulfate radicals (SO₄^•-) and hydroxyl radicals (^•OH) were formed on the surface of biochar. Based on the results of X-ray photoelectron spectroscopy (XPS), π-electron density and oxygen-containing functional groups (especially C-OH) on biochar surface were active centers for the catalytic reaction. Recycle experiments of biochar for 4 runs were carried out and the regeneration method of the catalyst was also studied.

Insights into the oxidation of organic contaminants by iron nanoparticles encapsulated within boron and nitrogen co-doped carbon nanoshell: Catalyzed Fenton-like reaction at natural pH

Iron nanoparticles encapsulated within boron and nitrogen co-doped carbon nanoshell (B/N-C@Fe) were synthesized through a novel and green pyrolysis process using melamine, boric acid, and ferric nitrate as the precursors. The surface morphology, structure, and composition of the B/N-C@Fe materials were thoroughly investigated. The materials were employed as novel catalysts for the activation of potassium monopersulfate triple salt (PMS) for the degradation of levofloxacin (LFX). Linear sweep voltammograms and quenching experiments were used to identify the mechanisms of PMS activation and LFX oxidation by B/N-C@Fe, where SO₄^- as well as HO were proved to be the main radicals for the reaction processes. This study also discussed how the fluvic acid and inorganic anions in the aqueous solutions affected the degradation of LFX and use this method to simulate the degradation in the real wastewater. The synthesized materials showed a high efficiency (85.5% of LFX was degraded), outstanding stability, and excellent reusability (77.7% of LFX was degraded in the 5th run) in the Fenton-like reaction of LFX. In view of these advantages, B/N-C@Fe have great potentials as novel strategic materials for environmental catalysis.

Novel synergy of Si-rich minerals and reactive MgO for stabilisation/solidification of contaminated sediment

Disposal of significant amounts of dredged contaminated sediment poses an economic and environmental problem worldwide. Transforming contaminated sediment into value-added construction materials using low-carbon MgO cement is a sustainable option; however, the weak mechanical strength and unreliable water-solubility of MgO cement restrict its practical engineering applications. This study elucidates the potential role of industrial Si-rich minerals in the performance enhancement of MgO-based products via the promotion of magnesium silicate hydrate (M-S-H) gel formation. Quantitative X-ray diffraction and ²⁹Si nuclear magnetic resonance analyses indicated that compositions and crystallinities of the Si-rich minerals significantly influence the formation and polymerisation of the M-S-H gel. Pulverised fly ash was found to be a promising Si-rich mineral for generating polymeric M-S-H gel, whereas incinerated sewage sludge ash samples demonstrated a low degree of polymerisation, and the use of glass powder samples gave a low yield of M-S-H. The formation of M-S-H gel enhanced the compressive strength and water resistance (strength retention after water immersion). Further experiments demonstrated that Si-modified MgO cement can transform dredged sediment into fill materials with satisfactory mechanical properties and contaminant immobilisation. Therefore, the synergy between reactive MgO and Si-rich industrial waste is a novel option for sustainable remediation and environmental applications.

The fabrication of a Co3O4/graphene oxide (GO)/polyacrylonitrile (PAN) nanofiber membrane for the degradation of Orange II by advanced oxidation technology

Treating water that has been polluted with chemical dyes is an important task related to water resources. Advanced oxidation processes are highly efficient for the destruction of organic contaminants. In this study, a Co₃O₄/graphene oxide (GO)/polyacrylonitrile (PAN) filter membrane was prepared through hydrothermal synthesis followed by vacuum filtration. The samples were characterised using different methods. The results showed that the Co₃O₄/GO sheets securely entered the voids of the PAN nanofibres. The Co₃O₄/GO/PAN filter membrane demonstrated the effective degradation of the organic dye Orange II, with a degradation rate of 93.5949%. The degradation rate remained at a high level after five cycles. The Co₃O₄/GO/PAN filter membrane has huge potential for application in industrial dye wastewater treatment.

Treating water that has been polluted with chemical dyes is an important task related to water resources.