Review on the occurrence, fate and removal of perfluorinated compounds during wastewater treatment

Spatiotemporal patterns of PFAS in water and crop tissue at a beneficial wastewater reuse site in central Pennsylvania

Per- and polyfluoroalkyl substances (PFAS) are a collective name for thousands of synthetic compounds produced to enhance consumer and industrial products since the 1940s. They do not easily degrade, and some are known to pose serious ecological and human health concerns at trace concentrations (ng L-1 levels). Per- and polyfluoroalkyl substances persist in treated wastewater and are inadvertently introduced into the environment when treated wastewater is reused as an irrigation source. The Pennsylvania State University (PSU) has been spray-irrigating its wastewater at a 2.45 km2 mixed-use agricultural and forested site known as the "Living Filter" since the 1960s. To understand the spatiotemporal patterns of 20 PFAS at the Living Filter, water samples were collected bimonthly from fall 2019 through winter 2021 from the PSU's wastewater effluent and from each of the site's 13 monitoring wells. Crop tissue was collected at the time of harvest to assess PFAS presence in corn silage and tall fescue grown at the study site. Total measured PFAS concentrations in the monitoring wells ranged from nondectable to 155 ng L-1 , with concentrations increasing with the direction of groundwater flow. Concentrations within each well exhibited little temporal variability across sampling events, with mixed relationships between PFAS and groundwater elevation observed between wells. Further, >84% of the PFAS present in livestock feed crops were short-chain compounds, with PFAS consumed annually by livestock fed crops harvested from the site estimated to be 2.46-7.67 mg animal-1 yr-1 . This research provides insight into the potential impacts of long-term beneficial reuse of treated wastewater on groundwater and crop tissue quality.

Non-target and target screening of per- and polyfluoroalkyl substances in landfill leachate and impact on groundwater in Guangzhou, China

Landfills are the main destination of many urban wastes containing per- and polyfluoroalkyl substances (PFAS), and PFAS may leach out from the waste and contaminate the surrounding groundwater. Here we investigated the occurrence of PFAS in leachate and surrounding groundwater from three landfills in Guangzhou, China by using a combined target and non-target approach. Non-target screening showed that a total of 651 PFAS with 96 classes were identified, including 17 legacy PFAS and 637 emerging PFAS. The quantitative target analysis of some PFAS revealed that the average removal rate of PFAS from the raw leachates were ranged between 62 % and 99 %. Statistical analysis and source analysis suggested that landfill leachate was a major source of PFAS in the groundwater within the landfills and downstream sites. The results from the combined target and non-target analyses demonstrated that PFAS in landfills could leach into the surrounding groundwater, and may affect the sustainable use of groundwater as a source of drinking water and pose a potential risk to human health.

Daphnia as a Sentinel Species for Environmental Health Protection: A Perspective on Biomonitoring and Bioremediation of Chemical Pollution

Despite available technology and the knowledge that chemical pollution damages human and ecosystem health, chemical pollution remains rampant, ineffectively monitored, rarely prevented, and only occasionally mitigated. We present a framework that helps address current major challenges in the monitoring and assessment of chemical pollution by broadening the use of the sentinel species Daphnia as a diagnostic agent of water pollution. And where prevention has failed, we propose the application of Daphnia as a bioremediation agent to help reduce hazards from chemical mixtures in the environment. By applying "omics" technologies to Daphnia exposed to real-world ambient chemical mixtures, we show improvements at detecting bioactive components of chemical mixtures, determining the potential effects of untested chemicals within mixtures, and identifying targets of toxicity. We also show that using Daphnia strains that naturally adapted to chemical pollution as removal agents of ambient chemical mixtures can sustainably improve environmental health protection. Expanding the use of Daphnia beyond its current applications in regulatory toxicology has the potential to improve both the assessment and the remediation of environmental pollution.

Emerging contaminants migration from pipes used in drinking water distribution systems: a review of the scientific literature

Migration of emerging contaminants (ECs) from pipes into water is a global concern due to potential human health effects. Nevertheless, a review of migration ECs from pipes into water distribution systems is presently lacking. This paper reviews, the reported occurrence migration of ECs from pipes into water distribution systems in the world. Furthermore, the results related to ECs migration from pipes into water distribution systems, their probable sources, and their hazards are discussed. The present manuscript considered the existing reports on migration of five main categories of ECs including microplastics (MPs), bisphenol A (BPA), phthalates, nonylphenol (NP), perfluoroalkyl, and polyfluoroalkyl substances (PFAS) from distribution network into tap water. A focus on tap water in published literature suggests that pipes type used had an important role on levels of ECs migration in water during transport and storage of water. For comparison, tap drinking water in contact with polymer pipes had the highest mean concentrations of reviewed contaminants. Polyvinyl chloride (PVC), polyamide (PA), polypropylene (PP), polyethylene (PE), and polyethylene terephthalate (PET) were the most frequently detected types of microplastics (MPs) in tap water. Based on the risk assessment analysis of ECs, levels of perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), perfluorodecanoic acid (PFDA), perfluorohexane sulfonate (PFHxS), and perfluorooctane sulfonate (PFOS) were above 1, indicating a potential non-carcinogenic health risk to consumers. Finally, there are still scientific gaps on occurrence and migration of ECs from pipes used in distribution systems, and this needs more in-depth studies to evaluate their exposure hazards on human health.

Occurrence of per- and polyfluoroalkyl substances (PFAS) in municipal solid waste landfill leachates from western China

Landfill leachate has been documented as a significant source of trace organic pollutants, comprising an expansive family of per- and polyfluoroalkyl substances (PFAS). This study presents the findings on the distribution of 13 perfluoroalkyl carboxylates (PFCAs) and 4 perfluoroalkyl sulfonates (PFSAs) in leachates from 6 municipal solid waste (MSW) landfills in western China. The total concentrations of 17 PFAS in sampled leachates ranged from 1805 to 43,310 ng/L, and 15 compounds were detected in all samples. The short-chain compounds perfluorobutane sulfonate (PFBS, mean mass fraction 23.1%) and perfluorobutyric acid (PFBA, mean mass fraction 20.6%) were dominant. There were higher PFAS concentrations in leachates from operating landfills (mean: 12,194 ng/L) compared to closed landfills (mean: 2747 ng/L), but there was no significant difference between young (< 10 years) and old landfills (> 10 years). Moderate to weak correlations were observed between PFAS concentrations and leachate properties, e.g., TN, NH₄⁺-N, TOC, and pH. This is the first report on the distribution of PFAS in landfill leachates from western China. The results have identified landfill leachate as an underestimated source of PFAS in the environment and have contributed to a more comprehensive evaluation on PFAS presence across China.

The development of diffusive equilibrium, high-resolution passive samplers to measure perfluoroalkyl substances (PFAS) in groundwater

Per- and poly-fluoroalkyl substances (PFAS) are a group of anthropogenic, highly recalcitrant organic compounds consisting of thousands of individual species that are of increasing importance as groundwater contaminants. In-situ measurements of PFAS would be useful to better understand vertical profiles and mobility, contamination in partially saturated media, and to reduce sampling artifacts associated with groundwater collection and analysis. Diffusive equilibrium, high-resolution passive samplers (HRPPs) can be directly driven (>10 m) in sediments or groundwater. The samplers equilibrate with porewater through diffusion across the sampler membrane, providing high spatial resolution (sample every 20 cm) porewater concentrations of dissolved species. The objective of this study was to develop an HRPP to measure PFAS in contaminated groundwater and saturated media. To achieve this objective, a screening study was conducted to demonstrate quantitative measurement of selected PFAS as well as the kinetics of uptake into a sampler using both nylon and stainless steel membranes. Utilizing the results of the screening study, a prototype sampler was demonstrated in a laboratory flow box. Over a deployment period of 28 days, concentrations of several perfluoroalkyl carboxylic acids (PFCAs), a perfluoroalkyl sulfonate (PFSA), and a precursor PFAS reached equilibrium with porewater (sampler concentration >90 percent of porewater concentration). Application of these samplers could provide improved understanding of the behavior of PFAS in saturated or partially saturated groundwater systems and allow better assessment of fate and transport in the subsurface. Reliable subsurface site characterization will yield robust site assessments, conceptual models, and improve remediation designs as well as increase confidence in post remedial assessments at PFAS-impacted locations.

Removal of PFASs from water by carbon-based composite photocatalysis with adsorption and catalytic properties: A review

Per- and polyfluoroalkyl substances (PFASs) are a class of persistent organic pollutants widely distributed in aquatic environments. The adsorption and photocatalytic methods have been widely used to remove PFASs in water because of their respective advantages. Still, they have apparent defects when used alone. Therefore, the adsorption and photocatalytic technologies are combined through suitable preparation methods, and the excellent properties of the two are used to synergize the treatment of organic pollutants. This strategy of "concentrating" pollutants and then degrading them in a centralized manner plays an essential role in removing trace PFASs. Nevertheless, a review focusing on this kind of adsorption photocatalyst system is lacking. This review will fill this gap and provide a reference for developing a carbon-based composite photocatalyst. Firstly, different carbon-based composite photocatalysts are reviewed in detail, focusing on the differences in various composite materials' excellent adsorption and catalytic properties. Secondly, the factors influencing the removal effect of carbon-based composite photocatalysts are discussed. Thirdly, the removal mechanism of carbon-based composite photocatalysts is summarized in detail. The removal process involves two steps: adsorption and photodegradation. The adsorption process involves multiple cooperative adsorption mechanisms, and photocatalytic degradation includes oxidative and reductive degradation. Fourthly, the comparison of adsorption-photocatalysis with common treatment techniques (including removal rate, range of adaptation, cost, and the possibility of expanding application) is summarized. Finally, the prospects of carbon-based composite photocatalysts for repairing PFASs are given by evaluating the performance of different composites.

Electrochemical oxidation combined with UV irradiation for synergistic removal of perfluorooctane sulfonate (PFOS) in water

The effect of electrochemical degradation on Magnéli phase Ti₄O₇ anode combined with UV irradiation on the removal of PFOS was systematically evaluated in the present study. A synergistic effect of electrolysis and UV irradiation rather than a simple additive effect for PFOS degradation was demonstrated experimentally and theoretically. The short wavelength irradiation within 400 nm is the main contribution to enhance the electrochemical degradation of PFOS, while the initial pH of the solution has little effect on the PFOS degradation. The increase of current density accelerates the removal of PFOS either by electrolysis treatment or the joint process. The time-dependent density functional theory (TD-DFT) calculation indicates that the synergistic effect of the electrolysis and UV irradiation is most likely due to the involvement of the excited PFOS induced under UV irradiation in the electrochemical reaction. This study provides the first mechanistic explanation for the electrochemical degradation of PFOS enhanced by UV irradiation.

Removal of perfluoroalkyl acids and dynamic succession of biofilm microbial communities in the decomposition process of emergent macrophytes in wetlands

Perfluoroalkyl acids (PFAAs) are emerging contaminants that pose significant environmental and health concerns. Water-sediment-macrophyte residue systems were established to clarify the removal efficiency of PFAAs, explore possible removal pathways, and profile the dynamic succession of biofilm microbial communities in the decomposition process. These systems were fortified with 12 PFAAs at three concentration levels. Iris pseudacorus and Alisma orientale were selected as the decomposing emergent macrophytes. The removal rates in the treatments with residues of I. pseudacorus (IP) and A. orientale (AO) were 34.4% to 88.9% and 36.5% to 89.9%, respectively, which were higher than those in the control groups (CG) (30.3% to 86.9%), suggesting that decomposition could alter the removal of PFAAs. Sediment made the greatest contributions (preloaded 14.5% to 77.8% of PFAAs in IP, 14.3% to 78.2% in AO, and 27.4% to 71.9% in CG). PFAAs could also be removed by macrophyte residue sorption (0.0190% to 13.0% in IP and 0.016% to 15.6% in AO) and bioaccumulation of residual biofilm (the contributions of biofilm microbes and their extracellular polymeric substances were 0.0110% to 3.93% and 0.918% to 34.4%, respectively, in IP and 0.0141% to 4.65% and 1.49% to 34.1%, respectively, in AO). Significant correlations were observed between sediment/residue adsorption and bioaccumulation of biofilm microbes, and were significantly correlated with perfluoroalkyl chain length (p < 0.05). The dynamic succession of residual biofilm microbial communities was investigated. The largest difference was found at the preliminary stage. The most similar communities were found in AO on day 70 (with specific genera Macellibacteroides and WCHB1-32) and in IP on day 35 (with specific genera Aeromonas and Flavobacterium). This study is useful to understand the removal of PFAAs during the decomposition process, providing further assistance in removing PFAAs during the life cycle of macrophytes in wetlands.

Electrochemical oxidation processes for PFAS removal from contaminated water and wastewater: fundamentals, gaps and opportunities towards practical implementation

Electrochemical oxidation (EO) is emerging as one of the most promising methods for the degradation of recalcitrant per- and poly-fluoroalkyl substances (PFASs) in water and wastewater, as these compounds cannot be effectively treated with conventional bio- or chemical approaches. This review examines the state of the art of EO for PFASs destruction, and comprehensively compares operating parameters and treatment performance indicators for both synthetic and real contaminated water and wastewater media. The evaluation shows the need to use environmentally-relevant media to properly quantify the effectiveness/efficiency of EO for PFASs treatment. Additionally, there is currently a lack of quantification of sorption losses, resulting in a likely over-estimation of process' efficiencies. Furthermore, the majority of experimental results to date indicate that short-chain PFASs are the most challenging and need to be prioritized as environmental regulations become more stringent. Finally, and with a perspective towards practical implementation, several operational strategies are proposed, including processes combining up-concentration followed by EO destruction.

Transformation and fate of pharmaceuticals, personal care products, and per- and polyfluoroalkyl substances during aerobic digestion of anaerobically digested sludge

Post-anaerobic aerobic digestion (PAAD) is a promising strategy to further reduce the volume and improve the quality of anaerobically digested sludge (ADS). However, the effect of PAAD process on the fate of pharmaceuticals and personal care products (PPCPs) and per- and polyfluoroalkyl substances (PFAS) remains largely unknown. In this study, fourteen PPCPs and fifteen PFAS were detected in ADS and evaluated regarding their fate and transformation in a laboratory aerobic digester operated with a hydraulic retention time of 13 days under 22 ℃. Twelve PPCPs demonstrated significant (p < 0.05) decrease in their total concentrations (dissolved and adsorbed fractions combined) with six compounds presenting substantial transformation (> 80%) after aerobic digestion. On the contrary, PFAS were not removed and their concentrations were either increased (increasing ratio: 91 - 571%) or consistent in the sludge during PAAD process, suggesting their recalcitrance to post aerobic digestion. More than half of PPCPs and PFAS demonstrated medium to strong sorption onto solids with their solid fraction higher than 50% in the ADS. After PAAD process, sorption of four PPCPs and three PFAAs to solids was enhanced in sludge.

Field-Based Distribution and Bioaccumulation Factors for Cyclic and Aliphatic Per- and Polyfluoroalkyl Substances (PFASs) in an Urban Sedentary Waterbird Population

The field-based distribution and bioaccumulation factor (BAF) for per- and polyfluoroalkyl substances (PFASs) were determined in residential Black Swans (Cygnus atratus) from an urban lake (Melbourne, Australia). The concentrations of 46 aliphatic and cyclic PFASs were determined by HPLC-MS/MS in serum and excrement from swans, and water, sediment, aquatic macrophytes, soil, and grass samples in and around the lake. Elevated concentrations of ∑₄₆PFASs were detected in serum (120 ng mL^-1) and excrement (110 ng g^-1 dw) were strongly related indicating a potential noninvasive sampling methodology. Environmental concentrations of PFASs were consistent with a highly impacted ecosystem and notably high concentrations of perfluoro-4-ethylcyclohexanesulfonate (PFECHS, 67584-42-3; C₈HF₁₅SO₃) were detected in water (27 ng L^-1) and swan serum (16 ng mL^-1). In the absence of credible putative alternative sources of PFECHS input to the lake, we propose that the use of high-performance motorsport vehicles is a likely source of contamination to this ecosystem. The BAF of perfluorocarboxylic acids increased with each additional CF₂ moiety from PFOA (15.7 L kg^-1 ww) to PFDoDA (3615 L kg^-1 ww). The BAF of PFECHS was estimated as 593 L kg^-1 ww, which is lower compared with that of PFOS (1097 L kg^-1 ww).

Sorption of Perfluorinated and Pharmaceutical Compounds in Plastics: A Molecular Simulation Study

The aim of the current study is to investigate the effect of temperature and degree of polymerisation on the thermodynamic interaction of perfluorinated compounds (PFCs) into plastics. The occurrence of contaminants of emerging concern such as pharmaceutical drugs, PFCs, microplastics (MPs), etc., in sources of drinking water have posed significant health risks to aquatic life and humans in recent years. These organic pollutants can interact with MPs and pose much higher health risks; consequently, MPs become a transport vector and thus alter their migration as well as occurrence in the environment. The purpose of this paper is to examine the adsorption mechanism of perfluorooctanoic acid (PFOA), perfluorooctane sulfonic acid (PFOS), and sulfamethazine (SMT)—relative to water—on polyethylene (PE) and polypropylene (PP) using an extended Flory–Huggins approach. The results suggest that in an aqueous environment, both PFOA and PFOS may be taken up preferentially by PP and PE, although less strongly by PE. The degree of polymerisation of PE and PP did not significantly influence the observed behaviour. In terms of sorption affinity, the observed affinity was PFOA>PFOS>SMT which was consistence for both PE and PP.

Interactions between dissolved organic matter and perfluoroalkyl acids in natural rivers and lakes: A case study of the northwest of Taihu Lake Basin, China

Understanding the interactions between dissolved organic matter (DOM) and perfluoroalkyl acids (PFAAs) is essential for predicting the distribution, transport, and fate of PFAAs in aquatic environments. Based on field investigations in the northwest of Taihu Lake Basin combined with laboratory experiments, we obtained DOM and PFAA concentrations as well as compositions and investigated key factors of DOM affecting PFAA variability and capture of PFAAs by DOM. Results indicated that the total concentrations of PFAAs were 73.4-689 ng/L in surface water and that PFAAs were dominated by C3-7 perfluoroalkyl carboxylic acids and perfluorooctane sulfonic acid. The main components of DOM included tyrosine-, fulvic-, and tryptophan-like substances. The Mantel test revealed a significant positive correlation between DOM and PFAAs (P = 0.0001). Fulvic-like substances were identified as the most crucial factors affecting PFAA variability. The laboratory experiments revealed that DOM can spontaneously aggregate into a microgel. Furthermore, 19.1-50.9% of PFAAs, DOM characteristic peaks, and several metals (Ca, Mg, Cu, and Fe) can be removed during aggregation, indicating the capacity of DOM binding organic/inorganic substances. The fulvic-like substances were more effectively removed than the protein-like substances. The distribution coefficients of all PFAAs except perfluorohexanoic acid significantly correlated with their perfluorinated carbon numbers (r = 0.975, p<0.001). Our results provided insights into the interactions between DOM and PFAAs, improving the understanding of the distribution, transport, and fate of PFAAs in aquatic environments.

Occurrence of priority substances in urban wastewaters of Istanbul and the estimation of the associated risks in the effluents

Increase in the contamination of the aquatic environments is a global challenge; hence, understanding the sources of priority substances (PSs) is essential. In an attempt to implement this principle, a year-long monitoring covering all seasons was carried out in the influents and effluents of four largest wastewater treatment plants (WWTPs) in Istanbul. Results obtained showed the presence of 48 PSs (66% of the target compounds) including pesticides, polycyclic aromatic hydrocarbons (PAHs), volatile organic compounds (VOCs), dioxins and dioxin-like compounds (DLCs), alkylphenols, phthalates, and metals ranging from low nanograms to micrograms per liter. Priority hazardous substances that were banned for long were still found to be present in wastewaters. PAHs, DLCs, alkylphenols, and metals were found to be present in all samples. Di(2-ethylhexyl) phthalate (DEHP) and DLCs were detected in more than 80% of the influent samples. Trichloromethane had the highest concentrations among the most frequently (80-100%) detected PSs in the influents and effluents. The potential risks that may arise from WWTP effluents containing PSs were estimated by calculating the risk quotients (RQs). Upon the risk estimation conducted on the PSs in effluents, monitoring of the endrin, alpha-cypermethrin, theta-cypermethrin, zeta-cypermethrin, quinoxyfen, bifenox, benzo-ghi-perylene, and DEHP is recommended for the WWTP effluents.

Critical review on negative emerging contaminant removal efficiency of wastewater treatment systems: Concept, consistency and consequences

Emerging contaminants (ECs) are not completely removed by wastewater treatment owing to their capabilities of making complexes, toxic derivatives, byproduct formation, and dynamic partitioning. Negative contaminant removal i.e., higher concentrations (up to 5731%) of these ECs in the effluent with respect to the influent sampled on the same occasions, is globally prevalent in almost all types of treatment systems. Conventional WWTPs showed the highest negative removal (NR) for Carbamazepine, and Carbadox. Conjugation-deconjugation, types of WWTPs, transformations, leaching, operational parameters, sampling schemes, and nature of substance governs the NR efficiencies. Among the various categories of micropollutants, pesticides and beta-blockers are reported to exhibit the maximum percentage of NR, posing threat to human and the environment. With > 200% of NR for beta-blockers, low blood-pressure related symptoms may likely to get more prevalent in the near future. Study red-flags this phenomenon of negative removal that needs urgent attention.

Sludge-based activated carbon and its application in the removal of perfluoroalkyl substances: A feasible approach towards a circular economy

This study explores the recovery of resources and energy from sewage sludge through the production of sludge-based activated carbon (SBAC) considering circular economy principles. The SBAC production costs were estimated under three scenarios considering various sludge dewatering/drying schemes to determine the production feasibility and its role in the circular economy. SBAC was tested in the removal of a mixture of nine commonly detected poly- and perfluoroalkyl substances (PFASs) in environmentally relevant concentrations of ∽50 μg/L in comparison to commercially available activated carbon (AC) using 5 mg of sorbent and 5 mL of a nine-PFAS mixture in deionised water. SBAC can be produced at approximately 1.2 US $/kg, which is substantially lower than the average production cost of commercial AC of >3 US $/kg. A net revenue ranging from 2 to 7 US $/kg SBAC was estimated by recycling the produced non-condensable gases and bio-oil to produce energy and selling the SBAC. Batch adsorption tests showed that the PFASs removal of SBAC was superior to that of granular AC and similar to that of powdered AC, reaching >91% to below the detection limit. The kinetics tests revealed that adsorption by SBAC and AC occurred within 15 min. The overall results demonstrate the potential of SBAC as an effective sorbent for PFASs, achieving waste-to-resources circular economy via resource and energy recovery from sewage sludge, eliminating sludge disposal and contaminant-leaching to the environment, and in enhancing the quality of wastewater effluent before discharge.

Analysis of per- and polyfluoroalkyl substances in Houston Ship Channel and Galveston Bay following a large-scale industrial fire using ion-mobility-spectrometry-mass spectrometry

Per- and polyfluoroalkyl substances (PFAS) are persistent organic pollutants of concern because of their ubiquitous presence in surface and ground water; analytical methods that can be used for rapid comprehensive exposure assessment and fingerprinting of PFAS are needed. Following the fires at the Intercontinental Terminals Company (ITC) in Deer Park, TX in 2019, large quantities of PFAS-containing firefighting foams were deployed. The release of these substances into the Houston Ship Channel/Galveston Bay (HSC/GB) prompted concerns over the extent and level of PFAS contamination. A targeted liquid chromatography-tandem mass spectrometry (LC-MS/MS)-based study of temporal and spatial patterns of PFAS associated with this incident revealed presence of 7 species; their levels gradually decreased over a 6-month period. Because the targeted LC-MS/MS analysis was focused on about 30 PFAS molecules, it may have missed other PFAS compounds present in firefighting foams. Therefore, we utilized untargeted LC-ion mobility spectrometry-mass spectrometry (LC-IMS-MS)-based analytical approach for a more comprehensive characterization of PFAS in these water samples. We analyzed 31 samples from 9 sites in the HSC/GB that were collected over 5 months after the incident. Our data showed that additional 19 PFAS were detected in surface water of HSC/GB, most of them decreased gradually after the incident. PFAS features detected by LC-MS/MS correlated well in abundance with LC-IMS-MS data; however, LC-IMS-MS identified a number of additional PFAS, many known to be components of firefighting foams. These findings therefore illustrate that untargeted LC-IMS-MS improved our understanding of PFAS presence in complex environmental samples.

Indigenous Bacillus paramycoides spp. and Alcaligenes faecalis: sustainable solution for bioremediation of hospital wastewater

Farmers near towns and cities are using a wide range of highly polluted wastewaters for crop irrigation in Pakistan due to severe freshwater shortage. The present study aimed to promote indigenous bacterial strains isolated from domestic, hospital, textile, pharmaceutical and mixed wastewaters to remove contaminants and colour and render these wastewaters safer for irrigation. Thirty seven bacterial strains were isolated from five wastewater samples collected from different sites in Lahore, Pakistan. Under optimal growth conditions, three isolates (D6, D7 and P1) showed >93% decolourisation potential in the treatment of hospital wastewater. 16S rDNA sequencing identified two of these isolates (D6 and D7) as showing 100% and 99.86% homology to Bacillus paramycoides spp. - novel strains from B. cereus group. Isolate P1 showed 97.47% homology to Alcaligenes faecalis. GCMS analysis of the untreated hospital wastewater revealed the presence of pharmaceutic pollutants, i.e. Phenol (876 µg/L), Salicylic acid (48 µg/L), Caffeine (7 µg/L), Naproxen (23 µg/L), Octadecene (185 µg/L) and Diazepam (14 µg/L). The analysis of treated hospital wastewaters showed percentage degradation of pharmaceutic pollutants (100%-43%) and significant reduction in the BOD₅ (91%-68%), COD (89%-52%) and heavy metals concentrations. These strains therefore can represent a low-cost and low-tech alternative to bioremediate complex matrices of hospital wastewater prior to crop irrigation to support the achievement of clean re-usable water in developing countries like Pakistan.

Contamination of perfluorooctane sulfonic acid (PFOS) and perfluorooctanoic acid (PFOA) in sediment of the Cau River, Vietnam

Perfluorooctane sulfonic acid (PFOS) and perfluorooctanoic acid (PFOA) are recognized as emerging environmental pollutants because of their high persistence in various environmental matrices and toxic effects on humans and animals. In Vietnam, PFOA and PFOS have been detected in surface water and sediment in recent studies. The objectives of this study were to evaluate the spatial and vertical distribution, determine the factors affecting the sorption onto sediment, and assess the environmental risk of PFOS and PFOA in the sediment of the Cau River. The average concentrations of PFOS and PFOA in the surface sediment were 2.66 ng/g and 0.84 ng/g, respectively. The highest concentrations were recorded in the areas receiving wastewater from domestic and industrial activities. According to the depth, the contents of target chemicals in the surface sediments (0-5 cm) were lower than those in the second layer (5-10 cm). The remaining layers have decreasing concentration as the depth of the sediment increases. The water-sediment distribution coefficient was relatively different for PFOS and PFOA with log K_d values ranging from 1.31 to 1.86 and from 0.08 to 1.31, respectively. This study also demonstrated that the level of PFOS and PFOA in sediment is significantly correlated with total organic carbon content of sediment. No apparent relation was found between PFOS, PFOA concentration in sediment, and particle size distribution. Risk quotients of the two compounds were below 0.01, indicating that the environmental risk in the sediment is negligible at present. The results of this study provide an overview of PFOS and PFOA contamination in sediment in the Cau River, Vietnam.

Per- and poly-fluoroalkyl substances in sediments from the water-level-fluctuation zone of the Three Gorges Reservoir, China: Contamination characteristics, source apportionment, and mass inventory and loadings

Sixteen paired surface sediment samples (0-5 cm, n = 32) covering upstream to downstream of water-level-fluctuation zone of Three Gorges Reservoir, China were collected in March 2018 (following six months of submergence) and September 2018 (after six months of exposure). Seventeen per- and poly-fluoroalkyl substances (PFASs) were quantified to evaluate contamination characteristics, apportion source categories and estimate mass inventory and loadings. The concentration of ΣPFASs ranged from 0.26 to 0.82 ng·g^-1 at high water-level (HWL) and 0.46-1.53 ng·g^-1 at low water-level (LWL). Perfluorooctanoic acid (PFOA, mean: 0.32 ng·g^-1) and perfluorooctane sulfonate (PFOS, mean: 0.12 ng·g^-1) dominated, accounting 44.9% and 16.3% of the total PFASs, respectively. The distribution of PFASs was more influenced by anthropogenic activities than physicochemical parameters of the sediments. Positive matrix factorization (PMF) identified PFOA-based products was the major sources (40.1% and 38.6%, respectively). Besides, the direct sources of PFOA-, PFOS-, PFNA-and PFBA-based products played the predominant role, while the indirect degradation of precursors contributed relatively little. The sediment (0-5 cm) mass inventory of PFASs at LWL (57.5 kg) was higher than HWL (39.3 kg). The annual mass loadings of the total PFASs, PFOA, PFOS, perfluoroundecanoic acid (PFUdA) and perfluorononanoic acid (PFNA) from the upstream to the middle-lower reaches of Yangtze River were 27.4 kg, 11.1 kg, 4.63 kg, 2.89 kg and 2.57 kg, respectively. This study could provide the basic datasets of PFASs in surface sediments of the TGR, and also indicate an important transport of PFASs from upstream to the lower reaches, which should be further studied as well.

A review on per- and polyfluorinated alkyl substances (PFASs) in microplastic and food-contact materials

Plastic, paper and cardboard are widely used as food contact materials (FCMs), due to its numerous favourable characteristics. However, they are usually coated with hazardous substances, such as per- and polyfluorinated alkyl substances (PFASs). PFASs, with its functional properties of oil- and water-repellency, can migrate from FCMs into the food and cause potential risk to human health. There are also increasing concerns about the harm that FCMs can cause to the environment. These concerns include accumulation of non-degradable plastics in the environment, generation of microplastics (MPs) and nanoplastics, and release of PFASs from FCMs. While many reviews have been conducted on PFASs in the environment, including their occurrence, fate, toxicity, biodegradation, migration in ecosystems and remediation technologies, a systematic review of PFASs in FCMs and MPs is currently lacking. In addition, our knowledge of the PFAS sorption processes on MPs is rather limited, and in particular their desorption processes. Thus, this review aims to (1) review the presence of various classes of PFASs in FCMs and their migration into food, (2) review the PFASs in MPs and summarize the sorption mechanisms, and factors that influence their sorption behaviour on MPs in the aquatic environment, and (3) identify the current research gaps and future research directions to predict the risks associated with the presence and sorption of PFASs in FCMs and MPs.

Background release and potential point sources of per- and polyfluoroalkyl substances to municipal wastewater treatment plants across Australia

Wastewater treatment plants (WWTPs) are known to be significant sources of per- and polyfluoroalkyl substances (PFAS) to the environment. In this study, PFAS were measured in the influent of 76 municipal wastewater treatment plants (WWTPs) serving approximately 53% of the Australian population. Of fourteen target PFAS, twelve analytes including six C5-C10 perfluoroalkyl carboxylic acids (PFCAs), four C4-10 perfluoroalkyl sulfonic acids (PFSAs) and two fluorotelomer sulfonates (6:2 and 8:2 FTS) were detected. Of these, PFOS, PFHxS and PFHxA had the highest median concentrations. The per capita background release of Σ₁₂ PFAS to WWTP influent in Australia was estimated to be 8.1-24 μg/d/per person. The background release was supplemented by contributions from catchment specific point sources (i.e., industry, airports, military bases, and landfills), whereby the number of industrial sites positively correlated with the per capita mass load of Σ₁₂ PFAS (r = 0.5-0.63, p < 0.01). The per capita mass loads were extrapolated to the entire Australian population, with estimates suggesting that approximately 1 kg/d of Σ₁₂ PFAS reach WWTPs in Australia (300-400 kg annually), with more than half of the PFAS (∼59%) attributed to background release and the remaining (∼41%) to catchment specific point sources. These data provide insight into the release of major PFAS to wastewater at a national scale in Australia.

Bioremediation of Perfluoroalkyl Substances (PFAS) by Anaerobic Digestion: Effect of PFAS on Different Trophic Groups and Methane Production Accelerated by Carbon Materials

Per- and polyfluoroalkyl substances (PFAS) are recalcitrant pollutants which tend to persist in soils and aquatic environments and their remediation is among the most challenging with respect to organic pollutants. Anaerobic digestion (AD) supplemented with low amounts of carbon materials (CM), acting as electron drivers, has proved to be an efficient process for the removal of organic compounds from wastewater. This work explores the impact of PFAS on different trophic groups in anaerobic communities, and the effect of carbon nanotubes (CNT), activated carbon (AC), and oxidized AC (AC-HNO₃), as electron shuttles on the anaerobic bioremoval of these compounds, based on CH₄ production. The inhibition of the specific methanogenic activity (SMA) exerted by perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), at a concentration of 0.1 mg L⁻¹, was below 10% for acetoclastic and below 15%, for acetogenic communities. Hydrogenotrophic methanogens were not affected by the presence of PFAS. All CM reduced the negative impact of PFAS on the CH₄ production rate, but AC was the best. Moreover, the methanization percentage (MP) of sewage sludge (SS) increased 41% in the presence of PFOS (1.2 g L⁻¹) and AC. In addition, AC fostered an increase of 11% in the MP of SS+PFOS, relative to the condition without AC. AC promoted detoxification of PFOA- and PFOS-treated samples by 51% and 35%, respectively, as assessed by Vibrio fischeri assays, demonstrating the advantage of bringing AD and CM together for PFAS remediation.

Removal potential of multiple perfluoroalkyl acids (PFAAs) by submerged macrophytes in aquatic environments: Tolerance of Vallisneria natans and PFAA removal in submerged macrophyte-microbiota systems

Perfluoroalkyl acids (PFAAs) have emerged as a global concern in aquatic environment remediation due to their abundance, persistence, bioaccumulation, and toxicity. To comprehensively understand the removal potential of multiple PFAAs by submerged macrophytes in aquatic environments, systematic investigations into the tolerance of the typical submerged macrophyte Vallisneria natans to 12 typical PFAAs and the removal capacity to PFAAs in V. natans-microbiota systems were carried out. Results showed that although PFAAs could induce the accumulation of hydrogen peroxide and malondialdehyde, V. natans was overall resistant to multiple PFAAs with natural concentrations. Catalase is one of the main strategies of V. natans to alleviate PFAA stress. Microbiota can remove 18.10-30.84% of the PFAAs from the water column. 24.35-73.45% of PFAAs were removed from water in V. natans-microbiota systems. The uptake of plant tissues and the bioaccumulation of microbiota were proposed as the main removal processes. The removal rates were significantly correlated with the perfluorinated carbon atoms numbers (p < 0.05). PFAAs and V. natans increased the relative abundance of Betaproteobacteria, Nostocales, Microscillaceae, Sphingobacteriales, SBR1031, Chlamydiales, Phycisphaerae, Caldilineales, Rhodobacterales, and Verrucomicrobiales. The present study suggested that V. natans can be a potential species to remove multiple PFAAs in aquatic environments, and further providing insights into the PFAAs' remediation.

Anaerobic degradation of perfluorooctanoic acid (PFOA) in biosolids by Acidimicrobium sp. strain A6

Anaerobic incubations were performed with biosolids obtained from an industrial wastewater treatment plant (WWTP) that contained perfluorooctanoic acid (PFOA), and with per- and polyfluoroalkyl substances- (PFAS) free, laboratory-generated, biosolids that were spiked with PFOA. Biosolid slurries were incubated for 150 days as is, after augmenting with either Acidimicrobium sp. Strain A6 or ferrihydrite, or with both, Acidimicrobium sp. Strain A6 and ferrihydrite. Autoclaved controls were run in parallel. Only the biosolids augmented with both, Acidimicrobium sp. Strain A6 and ferrihydrite showed a decrease in the PFOA concentration, in excess of 50% (total, dissolved, and solid associated). Higher concentrations of PFOA in the biosolids spiked with PFOA and no previous PFAS exposure allowed to track the production of fluoride to verify PFOA defluorination. The buildup of fluoride over the incubation time was observed in these biosolid incubations spiked with PFOA. A significant increase in the concentration of perfluoroheptanoic acid (PFHpA) over the incubations of the filter cake samples from the industrial WWTP was observed, indicating the presence of a non-identified precursor in these biosolids. Results show that anaerobic incubation of PFAS contaminated biosolids, after augmentation with Fe(III) and Acidimicrobium sp. Strain A6 can result in PFAS defluorination.

Poly- and Perfluorinated Alkyl Substances in Air and Water from Dhaka, Bangladesh

Bangladesh hosts extensive textile manufacturing, for some of which per- and polyfluorinated alkyl substances (PFAS) have been used to impart water and dirt repellency, among other things. Textile waste emissions to the atmosphere and discharge into rivers and other bodies of water could present a significant concern for human and ecosystem health, but there is little information on PFAS in Bangladesh. To assess the presence of ionic PFAS and their precursors in air and water from Dhaka, Bangladesh, polyethylene sheets were deployed for 28 days as passive samplers for neutral PFAS in outdoor air and water, while ionic PFAS were measured from discrete water grabs. Fluorotelomer alcohols (FTOHs) were detected at almost all sites in air and water; the most frequently detected compound was 6:2 FTOH, ranging from below instrumental detection limits (<IDL) to 70 ng m^-3 in air and from <IDL to -19 ng L^-1 in water. Of the ionic PFAS, perfluorobutanoic acid (PFBA), perfluorohexanoic acid, perfluorooctanoic acid, perfluorohexane sulfonic acid, and perfluorooctane sulfonic acid dominated in frequency of detection and magnitude, with concentrations ranging from 1.8 to 19.0 ng L^-1 in surface waters. The prevalence of 6:2 FTOH and PFBA across sites probably reflects their use in textile manufacturing and could indicate the industry's switch to shorter-chain PFAS alternatives. Environ Toxicol Chem 2022;41:334-342. © 2021 SETAC.

A review on degradation of perfluorinated compounds based on ultraviolet advanced oxidation

Perfluorinated compounds (PFCs), as emerging persistent pollutants, can exist for a long time in the environment due to their high stability. PFCs have been detected in drinking water, wastewater, and the human body. Studies have shown that PFCs pose a threat to human health and the ecological environment, which is expected to be listed in new drinking water regulations. Traditional processes, including coagulation, biological filtration, chlorination, ozonolysis, and ultraviolet light have ineffective removal efficiency on PFCs; however, advanced oxidation processes (AOP) based on ultraviolet (UV) light have good application prospects for the removal of PFCs. This study provides an overview of the removal of PFCs by UV-based AOPs; systematically introduces the research status of various UV-based AOPs from the perspectives of degradation pathways, degradation efficiency, influencing factors, formation of by-products; and comprehensively compares these different UV-based AOPs. Finally, the limitations of existing research and future research needs are discussed. This review aims to provide an overview for a better understanding of the degradation status and prospects of UV-based AOPs for the degradation of PFCs.

Persistent organic pollutants: The trade-off between potential risks and sustainable remediation methods

Persistent Organic Pollutants (POPs) have become a very serious issue for the environment because of their toxicity, resistance to conventional degradation mechanisms, and capacity to bioconcentrate, bioaccumulate and biomagnify. In this review article, the safety, regulatory, and remediation aspects of POPs including aromatic, chlorinated, pesticides, brominated, and fluorinated compounds, are discussed. Industrial and agricultural activities are identified as the main sources of these harmful chemicals, which are released to air, soil and water, impacting on social and economic development of society at a global scale. The main types of POPs are presented, illustrating their effects on wildlife and human beings, as well as the ways in which they contaminate the food chain. Some of the most promising and innovative technologies developed for the removal of POPs from water are discussed, contrasting their advantages and disadvantages with those of more conventional treatment processes. The promising methods presented in this work include bioremediation, advanced oxidation, ionizing radiation, and nanotechnology. Finally, some alternatives to define more efficient approaches to overcome the impacts that POPs cause in the hydric sources are pointed out. These alternatives include the formulation of policies, regulations and custom-made legislation for controlling the use of these pollutants.

Unravelling the impacts of perfluorooctanoic acid on anaerobic sludge digestion process

Perfluorooctanoic acid (PFOA) is a type of persistent organic pollutant that has been detected in wastewater treatment systems, subsequently entering the waste activated sludge (WAS) anaerobic digesters. Nevertheless, how PFOA affects the anaerobic digestion of WAS has never been reported till now. In this study, a series of batch digesters were set up to assess the performance of the anaerobic sludge digestion processes with exposures to different levels of PFOA. Experimental results revealed that the increased PFOA concentration (3-60 μg/g-TS) caused the 11.1-19.2% decrease in methane production than the control. Correspondingly, the relative abundances of several key microbes related to acidification (e.g., Longilinea sp.) and methanation (e.g., Methanosaeta sp.) decreased when exposed to PFOA, as demonstrated by microbial community analysis. Further investigations based on modelling and intermediate metabolites analysis confirmed the inhibition of acidification and methanation caused by PFOA, thus decreasing the methane production potential of WAS in anaerobic digestion.

Exploring the integrity of targeted PFASs in extracted wastewater samples during transport and storage stages

Little information exists on the effects of shipping and handling on per- and polyfluoroalkyl substances (PFASs) in environmental samples. Thus, we evaluated the integrity of dried wastewater extracts and the sensitivity of our high-resolution mass spectrometry (HRMS) instrument to perform such analyses by monitoring 13 representative PFASs in samples extracted, evaporated, and stored at room temperature up to one month. Relative to zero-day recoveries of six detected PFASs ranged between 94 and 124% (RSD <38%) for influents, between 88 and 126% (RSD <18%) for effluents after 28 days. Larger variabilities are tentatively associated with the lack of specific mass-labeled standards and the interactions between analytes and remaining matrix components over time. In a second stage, a mix of local and international dry-shipped wastewater samples were analyzed and the same PFASs were quantified. Up to six PFASs were identified, with median concentrations ranging from 1.3 (perfluoro butyl sulfonate (PFBS)) to 7.7 ng/L (perfluoro hexanoic acid (PFHxA)) and from 1.5 (PFBS) to 13.8 ng/L (PFHxA) in local influents and effluents respectively; and from 0.7 (perfluoro hexyl sulfonate (PFHxS)) to 52.8 ng/L (PFHxA) and from 0.5 (PFHxS) to 21.4 ng/L (PFHxA) in Greek influents and effluents, respectively. The importance of this study lies on the need to consider the wider recovery shifts and expanded variability ranges of PFASs derived from the transport and storage times of dried extracts, particularly when applied to HRMS and wide-scope screening approaches.

Detection and removal of poly and perfluoroalkyl polluting substances for sustainable environment

PFAs (poly and perfluoroalkyl compounds) are hazardous and bioaccumulative chemicals that do not readily biodegrade or neutralize under normal environmental conditions. They have various industrial, commercial, domestic and defence applications. According to the Organization for Economic Co-operation and Development, there are around 4700 PFAs registered to date. They are present in every stream of life, and they are often emerging and are even difficult to be detected by the standard chemical methods. This review aims to focus on the sources of various PFAs and the toxicities they impose on the environment and especially on humankind. Drinking water, food packaging, industrial areas and commercial household products are the primary PFAs sources. Some of the well-known treatment methods for remediation of PFAs presented in the literature are activated carbon, filtration, reverse osmosis, nano filtration, oxidation processes etc. The crucial stage of handling the PFAs occurs in determining and analysing the type of PFA and its remedy. This paper provides a state-of-the-art review of determination & tools, and techniques for remediation of PFAs in the environment. Improving new treatment methodologies that are economical and sustainable are essential for excluding the PFAs from the environment.

Natural and engineered clays and clay minerals for the removal of poly- and perfluoroalkyl substances from water: State-of-the-art and future perspectives

Poly- and perfluoroalkyl substances (PFAS) present globally in drinking-, waste-, and groundwater sources are contaminants of emerging concern due to their long-term environmental persistence and toxicity to organisms, including humans. Here we review PFAS occurrence, behavior, and toxicity in various water sources, and critically discuss their removal via mineral adsorbents, including natural aluminosilicate clay minerals, oxidic clays (Al, Fe, and Si oxides), organoclay minerals, and clay-polymer and clay‑carbon (biochar and graphene oxide) composite materials. Among the many remediation technologies, such as reverse osmosis, adsorption, advanced oxidation and biologically active processes, adsorption is the most suitable for PFAS removal in aquatic systems. Treatment strategies using clay minerals and oxidic clays are inexpensive, eco-friendly, and efficient for bulk PFAS removal due to their high surface areas, porosity, and high loading capacity. A comparison of partition coefficient values calculated from extracted data in published literature indicate that organically-modified clay minerals are the best-performing adsorbent for PFAS removal. In this review, we scrutinize the corresponding plausible mechanisms, factors, and challenges affecting the PFAS removal processes, demonstrating that modified clay minerals (e.g., surfactant, amine), including some commercially available products (e.g., FLUORO-SORB®, RemBind®, matCARE™), show good efficacy in PFAS remediation in contaminated media under field conditions. Finally, we propose future research to focus on the challenges of using clay-based adsorbents for PFAS removal from contaminated water due to the regeneration and safe-disposal of spent clay adsorbents is still a major issue, whilst enhancing the PFAS removal efficiency should be an ongoing scientific effort.

Perfluorinated alkyl substances: Sewage treatment and implications for receiving waters

This study comprises a detailed analysis of data for perfluorooctanesulfonic acid (PFOS), and perfluorooctanoic acid (PFOA) for over 600 wastewater treatment works effluents (WwTW) as well as samples upstream and downstream of each discharge of effluent into its receiving water. This has allowed an investigation of not only the effectiveness of removal of the perfluoroalkyl substances (PFAS) compounds during wastewater treatment but also implications for compliance with the environmental quality standard (EQS) set for PFOS under the Water Framework Directive. It is shown that effluents contain concentrations of PFOS that exceed the annual average EQS by a factor between 1.1-fold and 40-fold. The corresponding factors for PFOA are between 2-fold and 22-fold. The presence of high concentrations upstream, means that between a quarter and a third of individual effluents are found to reduce the concentration of fluorocarbons in the river downstream of the discharge point. The elevated concentrations upstream of the studied wastewater treatment works suggest inputs of these perfluoro compounds into the aquatic environment are ubiquitous and therefore difficult to address from simply setting permit conditions for individual WwTW. The freshwater EQS set for PFOS is based on several worst-case accumulation coefficients and large safety factors, which, when combined, result in a sub ng/L EQS. Consequently, the use of the biota derived quality standard may be a more realistic measure of environmental risk. It may be prudent, to assess the effectiveness of controls implemented in the last few years before considering widespread end-of-pipe treatment.

A graphene-based hydrogel monolith with tailored surface chemistry for PFAS passive sampling

Aquatic contamination by per- and polyfluorinated alkyl substances (PFAS) has attracted global attention due to their environmental and health concerns. Current health advisories and surface water regulatory limits require PFAS detection in the parts per trillion (ppt) range. One way to achieve those low detection limits is to use a reliable passive sampling-based monitoring tool for PFAS, as exists for numerous nonpolar persistent organic pollutants. Here we introduce a new graphene-based hydrogel monolith and describe its synthesis, chemical functionalization, property characterization, and testing as a PFAS equilibrium passive sampler. The graphene monoliths were self-assembled by hydrothermal treatment from graphene oxide (GO) aqueous dispersions to produce free standing cylinders of ~563 mm³ volume consisting of ~4 wt-% thin-walled porous graphene and ~96 wt-% water. The uptake of 23 PFAS was measured on the as-produced monoliths, and equilibrium partition coefficients (K_SW), were derived for longer chain (C≥8) perfluoroalkyl acids (PFAA) and neutral precursors such as sulfonamides (log K_SW range 1.9 - 3.6). To increase the K_SW for shorter chain PFAA, the monoliths were chemically modified by a new diazonium-based grafting reaction that introduces positive surface charge without damage to the graphenic backbone. Introduction of benzylamine moieties through the diazonium intermediate switches zeta potential at pH 7 from -45mV (as-produced graphene) to + 5mV. This modification increased the sorption of short and middle chain PFAA by ten-fold (e.g. log K_SW for PFBA increased from 1.3 to 2.2), thereby improving the functionality of the passive sampler device for a wider range of PFAS. Field deployments demonstrated that the graphene monoliths were capable of detecting key PFAS in the Delaware River.

NMR spectroscopy of wastewater: A review, case study, and future potential

NMR spectroscopy is arguably the most powerful tool for the study of molecular structures and interactions, and is increasingly being applied to environmental research, such as the study of wastewater. With over 97% of the planet's water being saltwater, and two thirds of freshwater being frozen in the ice caps and glaciers, there is a significant need to maintain and reuse the remaining 1%, which is a precious resource, critical to the sustainability of most life on Earth. Sanitation and reutilization of wastewater is an important method of water conservation, especially in arid regions, making the understanding of wastewater itself, and of its treatment processes, a highly relevant area of environmental research. Here, the benefits, challenges and subtleties of using NMR spectroscopy for the analysis of wastewater are considered. First, the techniques available to overcome the specific challenges arising from the nature of wastewater (which is a complex and dilute matrix), including an examination of sample preparation and NMR techniques (such as solvent suppression), in both the solid and solution states, are discussed. Then, the arsenal of available NMR techniques for both structure elucidation (e.g., heteronuclear, multidimensional NMR, homonuclear scalar coupling-based experiments) and the study of intermolecular interactions (e.g., diffusion, nuclear Overhauser and saturation transfer-based techniques) in wastewater are examined. Examples of wastewater NMR studies from the literature are reviewed and potential areas for future research are identified. Organized by nucleus, this review includes the common heteronuclei (¹³C, ¹⁵N, ¹⁹F, ³¹P, ²⁹Si) as well as other environmentally relevant nuclei and metals such as ²⁷Al, ⁵¹V, ²⁰⁷Pb and ¹¹³Cd, among others. Further, the potential of additional NMR methods such as comprehensive multiphase NMR, NMR microscopy and hyphenated techniques (for example, LC-SPE-NMR-MS) for advancing the current understanding of wastewater are discussed. In addition, a case study that combines natural abundance (i.e. non-concentrated), targeted and non-targeted NMR to characterize wastewater, along with in vivo based NMR to understand its toxicity, is included. The study demonstrates that, when applied comprehensively, NMR can provide unique insights into not just the structure, but also potential impacts, of wastewater and wastewater treatment processes. Finally, low-field NMR, which holds considerable future potential for on-site wastewater monitoring, is briefly discussed. In summary, NMR spectroscopy is one of the most versatile tools in modern science, with abilities to study all phases (gases, liquids, gels and solids), chemical structures, interactions, interfaces, toxicity and much more. The authors hope this review will inspire more scientists to embrace NMR, given its huge potential for both wastewater analysis in particular and environmental research in general.

An electrocoagulation and electrooxidation treatment train to remove and degrade per- and polyfluoroalkyl substances in aqueous solution

This study examined the feasibility of a novel treatment train that combines electrocoagulation (EC) with electrooxidation (EO) treatment to remove and degrade per- and polyfluoroalkyl substances (PFASs) from water. Electrocoagulation with a zinc anode could effectively remove PFASs from water, and long-chain PFASs (C₇-C₁₀) tended to have a higher removal rate. Foam was generated when a relatively high current density (>1 mA cm^-2) was applied to a relatively high PFAS concentration (each PFAS > 0.1 μM) during EC, which promoted the separation of PFASs from the bulk solution, especially for long-chain PFASs. Isotherm-like adsorption results indicated that competitive adsorption on floc occurred between PFASs when no foam was produced in a solution containing 10 different PFASs. Acid dissolution methods could recover and concentrate 10 PFASs in controlled volumes from both the floc and the foam, and it was also successfully applied in groundwater collected from a contaminated site. The concentrated PFASs in the acid solutions were efficiently destructed using EO treatment with a Ti₄O₇ anode at 10 mA cm^-2, and no supplement of electrolyte was needed for the floc dissolved solution. This electrochemical-based process can economically separate, concentrate and destroy PFASs in groundwater and wastewater.

Development and Applications of Novel DGT Passive Samplers for Measuring 12 Per- and Polyfluoroalkyl Substances in Natural Waters and Wastewaters

Extensive and long-term use of per- and polyfluoroalkyl substances (PFASs) has caused their widespread distribution in aquatic systems. A new diffusive gradients in thin-films (DGT) passive sampling method based on weak anion exchanger (WAX) binding layer is developed here for monitoring five perfluoroalkyl carboxylic acids (PFCAs), five perfluoroalkanesulfonic acids (PFSAs) and two PFASs (6:2 FTSA and GenX) in waters. Performance of WAX-DGTs was independent of environmental conditions, namely pH (3.03-8.96), ionic strength (1-500 mM), and DOM content (4-30 mg L^-1). Diffusion coefficients (D) of the 12 PFASs in the diffusive gels were measured, 9 for the first time. Linear correlations between D and perfluoroalkyl chain lengths (CF₂) were established to obtain D for congener chemicals with the similar functional group and structure. The binding capacity of the WAX-DGT sampler was at least 440 μg PFASs per sampler, sufficient for applications in waters across a wide range of conditions and PFASs concentrations. Successful applications of WAX based DGT samplers in a wastewater treatment plant (WWTP) and three rivers has demonstrated that DGT is a powerful tool for monitoring, surveillance and research of these 12 PFASs in aquatic systems, and can be extended to wider suites of PFs in future.

A review of the occurrence, transformation, and removal of poly- and perfluoroalkyl substances (PFAS) in wastewater treatment plants

Poly- and perfluoroalkyl substances (PFAS) comprise more than 4,000 anthropogenically manufactured compounds with widescale consumer and industrial applications. This critical review compiles the latest information on the worldwide distribution of PFAS and evaluates their fate in wastewater treatment plants (WWTPs). A large proportion (>30%) of monitoring studies in WWTPs were conducted in China, followed by Europe (30%) and North America (16%), whereas information is generally lacking for other parts of the world, including most of the developing countries. Short and long-chain perfluoroalkyl acids (PFAAs) were widely detected in both the influents (up to 1,000 ng/L) and effluents (15 to >1,500 ng/L) of WWTPs. To date, limited data is available regarding levels of PFAS precursors and ultra-short chain PFAS in WWTPs. Most WWTPs exhibited low removal efficiencies for PFAS, and many studies reported an increase in the levels of PFAAs after wastewater treatment. The analysis of the fate of various classes of PFAS at different wastewater treatment stages (aerobic and/aerobic biodegradation, photodegradation, and chemical degradation) revealed biodegradation as the primary mechanism responsible for the transformation of PFAS precursors to PFAAs in WWTPs. Remediation studies at full scale and laboratory scale suggest advanced processes such as adsorption using ion exchange resins, electrochemical degradation, and nanofiltration are more effective in removing PFAS (~95-100%) than conventional processes. However, the applicability of such treatments for real-world WWTPs faces significant challenges due to the scaling-up requirements, mass-transfer limitations, and management of treatment by-products and wastes. Combining more than one technique for effective removal of PFAS, while addressing limitations of the individual treatments, could be beneficial. Considering environmental concentrations of PFAS, cost-effectiveness, and ease of operation, nanofiltration followed by adsorption using wood-derived biochar and/or activated carbons could be a viable option if introduced to conventional treatment systems. However, the large-scale applicability of the same needs to be further verified.

Emerging pollutants in Nigeria: A systematic review

Emerging pollutants represent a group of synthetic or naturally occurring compounds that are not normally monitored within the environment but can enter into the environment and cause different adverse ecological and health effects. This systematic review identified the various emerging pollutants in Nigeria. The following databases, ScienceDirect, PubMed, Google Scholar, and African Journals OnLine (AJOL) were searched to identify studies on pollutants of emerging concerns in Nigeria. A total of 933 articles were identified out of which 30 articles were selected to be eligible for the study. Over 250 emerging pollutants were identified and divided into 9 major groups which are personal care products, pharmaceuticals, industrial chemicals, polycyclic aromatic hydrocarbons, volatile organic compounds, pesticides, mycotoxins, radionuclides and electromagnetic radiations (Gamma radiation) and other pollutants of emerging concerns such as microbes, microplastics, and particulate matter. These pollutants are found in water bodies and underground waters, soils and sediments, biological systems, and ambient air at different concentrations with seasonal variations. Some of these pollutants act as endocrine disruptors, β-adrenergic receptors agonist blockers, oxidative stress inducers and can cause genetic alterations in DNA and epigenetic reprogramming through global DNA methylation, gene-specific CpG methylation and microRNA expression. Emerging pollutants of public health concern in Nigeria are on the increase and are threat to both ecological and human health.

Legacy and emerging per- and polyfluoroalkyl substances (PFASs) in Dagang Oilfield: Multimedia distribution and contributions of unknown precursors

A systematic survey was conducted on twenty-six per- and polyfluoroalkyl substances (PFASs) in fifty-one paired samples of surface water, sediment, and soil from Dagang Oilfield, Tianjin, China. Perfluorooctanoic acid, perfluorooctane sulfonic acid, p-perfluorous nonenoxybenzenesulfonate (OBS), and 6:2 fluorotelomer sulfonamidoalkyl betaine (6:2 FTAB) were ubiquitous in the oilfield with field log K_d of 1.3-2.2, indicating a high partition potential from surface water to sediment. Total petroleum hydrocarbons (TPH) are a predictor for PFAS contamination at oilfield. The concentrations of OBS and 6:2 FTAB were higher in surface water and sediment with elevated TPH level. With total oxidizable precursor assay, unknown precursors for C2-C3 perfluoroalkyl carboxylic acids (PFCAs) (57-99 mol%) contributed more than those for C4-C12 PFCAs in the three mediums. The unknown C4-, C6-, and C8-based precursors tended to be precursors for perfluoroalkyl sulfonates at the oilfield, and C8 fluorotelomer-based precursors particularly occurred in the surface water. The concentrations of C4- and C8-based precursors were found positively correlated with TPH levels (r = 0.67-0.72, p < 0.05), while C6 precursors may also come from other sources. Further studies are necessary to clarify the mass balance and risk assessment for unknown PFASs.

PFAS removal by ion exchange resins: A review

Per- and poly-fluoroalkyl substances (PFAS) represent a large family of anthropogenic organic compounds with a wide range of industrial and commercial applications. PFAS have become a global concern due to their toxicity and bio-accumulative properties. PFAS species have been ubiquitously detected in natural waters, wastewaters, sludge, and aquatic and terrestrial species which are anionic, zwitterionic and neutral. The ion exchange (IX) process for PFAS removal is an efficient technology for the remediation of PFAS-laden surface, ground and effluent wastewaters. This approach is more effective towards eliminating emerging short-chain PFAS which are not removed by carbon-based adsorption processes. This article presents a state-of-the-art review of PFAS removal from water via IX process. The evaluation and comparison of various IX resins in terms of kinetics and isotherms is presented. Literature data indicates that IX isotherm uptake capacity for perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) can range up to 5 mmol/g on commercially available IX resins such as IRA 958 and IRA 67. The mechanism involved in the PFAS uptake process, such as diffusion, electrostatic interactions and hydrophobic effects are discussed. The effects of the eluent variability on the regeneration efficacy are also highlighted and the effect of single-use vs reuse for newly developed PFAS-specific IX resins are also examined based on the reviewed literature.

Removal of perfluoroalkyl acids (PFAAs) in constructed wetlands: Considerable contributions of submerged macrophytes and the microbial community

The broad application of perfluoroalkyl acids (PFAAs) has attracted global concern regarding their adverse environmental effects. The possible removal processes of PFAAs in constructed wetlands were excavated and quantified using two typical submerged macrophytes (rooted Potamogeton wrightii and rootless Ceratophyllum demersum). Our results showed that 33.59-88.99% of PFAAs could be removed via not only sediment sorption or phytoextraction but also by the bioaccumulation of microbiota. The sediment acts as a vital sink for PFAAs, preloading 23.51-50.09% and 16.65-52.18% of PFAAs in treatments with P. wrightii (Pw1) and C. demersum (Cd1), respectively. C. demersum showed a better capacity to accumulate PFAAs (0.91-32.03%) than P. wrightii (<10%). Considerable PFAAs were observed to be distributed in microbes, underlining the non-negligible role of microbiota in bioaccumulating PFAAs. The contributions of planktonic microbes, biofilm microbes, and extracellular polymeric substances in biofilms were 0.39-20.96%, 0.03-7.95%, and 0.39-14.15% in Pw1 and 0.23-15.68%, 0.01-15.68%, and 0.53-26.77% in Cd1, respectively. The adsorption/uptake was significantly correlated with the perfluoroalkyl chain length (p<0.05), except for the uptake of biofilms in C. demersum. Furthermore, PFAAs and submerged macrophytes could decrease the richness of microbiota but increase the relative abundance of some strains in Betaproteobacteriales, Sphingomonadales, and Cytophagales. Our results were helpful for understanding the removal processes of PFAAs in constructed wetlands and their linkages with PFAA properties, thus further providing insight into the management and removal of emerging organic contaminants.

Per- and polyfluoroalkyl substances thermal destruction at water resource recovery facilities: A state of the science review

Per- and polyfluoroalkyl substances (PFAS) are a recalcitrant group of chemicals and can be found throughout the environment. They often collect in wastewater systems with virtually no degradation prior to environmental discharge. Some PFAS partitions to solids captured in wastewater treatment which require further processing. Of all the commonly applied solids treatment technologies, incineration offers the only possibility to completely destroy PFAS. Little is known about the fate of PFAS through incineration, in particular, for the systems employed in water resource recovery facilities (WRRF). This review covers available research on the fate of PFAS through incineration systems with a focus on sewage sludge incinerators. This research indicates that at least some PFAS destruction will occur with incineration approaches used at WRRFs. Furthermore, PFAS in flue gas, ash, or water streams used for incinerator pollution control may be undetectable. Future research involving full-scale fate studies will provide insight on the efficacy of PFAS destruction through incineration and whether other compounds of concern are generated. PRACTITIONER POINTS: Thermal processing is the only commercial approach available to destroy PFAS. Thermal degradation conditions required for destruction of PFAS during incineration processes are discussed. Fate of PFAS through water resource recovery facility incineration technologies remains unclear. Other thermal technologies such as smoldering combustion, pyrolysis, gasification, and hydrothermal liquefaction provide promise but are in developmental phases.

Sorption of perfluoroalkylated substances (PFASs) onto granular activated carbon and biochar

Perfluoroalkyl and polyfluoroalkyl substances (PFASs) have attracted increasing concerns owing to their potential ecotoxicological effects. The sorption of PFASs, i.e. perfluorooctanoic acid (PFOA), perfluorooctane sulfonic acid (PFOS), perfluorobutanoic acid (PFBA) and perfluorobutansulfonic acid (PFBS), by granular activated carbon (GAC) and softwood-derived biochar was studied. The sorption equilibrium of PFASs on GAC was obtained within 3-24 h, while the time required to reach equilibrium for biochar was 12-48 h. PFASs sorption on both GAC and biochar were well represented by the pseudo-second-order model. In the case of sorption isotherms, the PFAS sorption capacity was chain-length dependent with following order: PFOS > PFOA > PFBS > PFBA. GAC exhibited high maximum Langmuir sorption capacity for both PFOS (123.5 µmol g^-1) and PFOA (86.2 µmol g^-1), which were 43% and 39.6% greater than biochar. The maximum sorption capacity for PFBS on GAC (48.3 µmol g^-1) was higher than that for PFBA (31.4 µmol g^-1), while the opposite sorption trend was observed for biochar. The sorption mechanisms involved both electrostatic attraction and hydrophobic interaction. The sorption of PFASs increased with the decrease in pH. The competitive sorption of PFASs occurred during the sorption process, resulting in decreased PFASs removal efficiencies. The Fourier transform infrared (FTIR) analyses indicated the presence of a variety of functional groups on the surfaces of adsorbents. Some FTIR responses shifted after sorption, indicating electronic interactions during sorption. All the results indicate that adsorption technology is a feasible method to control the contamination of PFASs, and both GAC and biochar are effective adsorbents for PFASs removal from wastewater.

Optimized suspect screening approach for a comprehensive assessment of the impact of best management practices in reducing micropollutants transport in the Potomac River watershed

The vast number of chemicals potentially reaching aquatic environment pose a challenge in maintaining the quality of water resources. However, best management practices to improve water quality are typically focused on reducing nutrient transport without assessing how these practices may impact the occurrence of micropollutants. The potential for co-management of nutrients and organic micropollutants exists, but few studies have comprehensively evaluated the suite of contaminants associated with different water quality management practices (riparian zone restoration, stormwater management, etc.). Furthermore, most studies dealing with the determination of micropollutants in environmental samples include only a limited number of target analytes, leaving many contaminants undetected. To address this limitation, there has been a gradual shift in environmental monitoring from using target analysis to either suspect screening analysis (SSA) or non-targeted analysis (NTA), which relies on accurate mass measurements, mass spectral fragmentation patterns, and retention time information obtained using liquid chromatography coupled to high-resolution mass spectrometry. The work presented in this paper focuses on a wide-scope detection of micropollutants in surface water samples from the Potomac River watershed (United States). An in-house database composed of 1039 compounds based on experimental analysis of primary standards was established, and SSA workflow was optimized and applied to determine the presence of micropollutants in surface water. A total of 103 micropollutants were detected in the samples, some of which are contaminants that were not previously monitored and belong to various classes such as pharmaceuticals, personal care products, per-and polyfluoroalkyl substances and other persistent industrial chemicals. The impact of best management practices being implemented for nitrogen and phosphorus reductions were also assessed for their potential to reduce micropollutant transport. This work illustrates the advantages of suspect screening methods to determine a large number of micropollutants in environmental samples and reveals the potential to co-manage a diverse array of micropollutants based on shared transport and transformation mechanisms in watersheds.

Linking PFAS partitioning behavior in sewage solids to the solid characteristics, solution chemistry, and treatment processes

Per- and polyfluoroalkyl substances (PFAS) have gained increasing attention due to the potential health risks that they present. Secondary sludge and biosolids are known as notable PFAS emission routes to the environment. In this study, partitioning behavior of 14 PFAS were investigated across four secondary wastewater treatment types (activated sludge, trickling filter, biological nutrient removal, and rotating biological contactor; n = 10) and three sludge stabilization methods (composting, aerobic digestion, and anaerobic digestion; n = 6). Batch experiments were conducted to evaluate how PFAS sorption to secondary sludge and biosolid was affected by various treatment methods, solid properties, and solution chemistry parameters. Insignificant differences in compound-specific partitioning coefficients (K_d) were observed among the four secondary treatment methods. However, sludge stabilization resulted in significantly different partitioning behavior among biosolid samples, in which anaerobically digested biosolids generally had significantly higher K_d values compared to aerobically digested and composted biosolids (anaerobic digestion > aerobic digestion > composting). Multiple linear regression models were developed to explain analyte-specific K_d values across the biosolid samples and identified that solid-specific property significance was as follows: protein fraction > organic matter fraction > lipid fraction. Stabilization generally decreased the PFAS sorption capacity relative to the secondary sludge samples. Furthermore, PFAS K_d increased with elevated calcium concentrations and ionic strengths and decreased with increasing pH values in sludge and biosolid samples. These findings could inform the decision-making process to reduce the release of PFAS to the environment.