Dynamical Magnetic Response of Iron Oxide Nanoparticles Inside Live Cells

Hydrotalcite-Embedded Magnetite Nanoparticles for Hyperthermia-Triggered Chemotherapy

A magnetic nanocomposite, consisting of Fe₃O₄ nanoparticles embedded into a Mg/Al layered double hydroxide (LDH) matrix, was developed for cancer multimodal therapy, based on the combination of local magnetic hyperthermia and thermally induced drug delivery. The synthesis procedure involves the sequential hydrolysis of iron salts (Fe²⁺, Fe³⁺) and Mg²⁺/Al³⁺ nitrates in a carbonate-rich mild alkaline environment followed by the loading of 5-fluorouracil, an anionic anticancer drug, in the interlayer LDH space. Magnetite nanoparticles with a diameter around 30 nm, dispersed in water, constitute the hyperthermia-active phase able to generate a specific loss of power of around 500 W/g-Fe in an alternating current (AC) magnetic field of 24 kA/m and 300 kHz as determined by AC magnetometry and calorimetric measurements. Heat transfer was found to trigger a very rapid release of drug which reached 80% of the loaded mass within 10 min exposure to the applied field. The potential of the Fe₃O₄/LDH nanocomposites as cancer treatment agents with minimum side-effects, owing to the exclusive presence of inorganic phases, was validated by cell internalization and toxicity assays.

Multiscale modelling of magnetostatic effects on magnetic nanoparticles with application to hyperthermia

We extend a renormalization group-based (RG) coarse-graining method for micromagnetic simulations to include properly scaled magnetostatic interactions. We apply the method in simulations of dynamic hysteresis loops at clinically relevant sweep rates and at 310 K of iron oxide nanoparticles (NPs) of the kind that have been used in preclinical studies of magnetic hyperthermia. The coarse-graining method, along with a time scaling involving sweep rate and Gilbert damping parameter, allow us to span length scales from the unit cell to NPs approximately 50 nm in diameter with reasonable simulation times. For both NPs and the nanorods composing them, we report effective uniaxial anisotropy strengths and saturation magnetizations, which differ from those of the bulk materials magnetite and maghemite of which they are made, on account of the combined non-trivial effects of temperature, inter-rod exchange, magnetostatic interactions and the degree of orientational order within the nanorod composites. The effective parameters allow treating the NPs as single macrospins, and we find for the test case of calculating loops for two aligned NPs that using the dipole approximation is sufficient for distances beyond 1.5 times the NP diameter. We also present a study on relating integration time step to micromagnetic cell size, finding that the optimal time step size scales approximately linearly with cell volume.

Embracing Defects and Disorder in Magnetic Nanoparticles

Iron oxide nanoparticles have tremendous scientific and technological potential in a broad range of technologies, from energy applications to biomedicine. To improve their performance, single-crystalline and defect-free nanoparticles have thus far been aspired. However, in several recent studies, defect-rich nanoparticles outperform their defect-free counterparts in magnetic hyperthermia and magnetic particle imaging (MPI). Here, an overview on the state-of-the-art of design and characterization of defects and resulting spin disorder in magnetic nanoparticles is presented with a focus on iron oxide nanoparticles. The beneficial impact of defects and disorder on intracellular magnetic hyperthermia performance of magnetic nanoparticles for drug delivery and cancer therapy is emphasized. Defect-engineering in iron oxide nanoparticles emerges to become an alternative approach to tailor their magnetic properties for biomedicine, as it is already common practice in established systems such as semiconductors and emerging fields including perovskite solar cells. Finally, perspectives and thoughts are given on how to deliberately induce defects in iron oxide nanoparticles and their potential implications for magnetic tracers to monitor cell therapy and immunotherapy by MPI.

Advanced analysis of magnetic nanoflower measurements to leverage their use in biomedicine

Magnetic nanoparticles are an important asset in many biomedical applications ranging from the local heating of tumours to targeted drug delivery towards diseased sites. Recently, magnetic nanoflowers showed a remarkable heating performance in hyperthermia experiments thanks to their complex structure leading to a broad range of magnetic dynamics. To grasp their full potential and to better understand the origin of this unexpected heating performance, we propose the use of Kaczmarz' algorithm in interpreting magnetic characterisation measurements. It has the advantage that no a priori assumptions need to be made on the particle size distribution, contrasting current magnetic interpretation methods that often assume a lognormal size distribution. Both approaches are compared on DC magnetometry, magnetorelaxometry and AC susceptibility characterisation measurements of the nanoflowers. We report that the lognormal distribution parameters vary significantly between data sets, whereas Kaczmarz' approach achieves a consistent and accurate characterisation for all measurement sets. Additionally, we introduce a methodology to use Kaczmarz' approach on distinct measurement data sets simultaneously. It has the advantage that the strengths of the individual characterisation techniques are combined and their weaknesses reduced, further improving characterisation accuracy. Our findings are important for biomedical applications as Kaczmarz' algorithm allows to pinpoint multiple, smaller peaks in the nanostructure's size distribution compared to the monomodal lognormal distribution. The smaller peaks permit to fine-tune biomedical applications with respect to these peaks to e.g. boost heating or to reduce blurring effects in images. Furthermore, the Kaczmarz algorithm allows for a standardised data analysis for a broad range of magnetic nanoparticle samples. Thus, our approach can improve the safety and efficiency of biomedical applications of magnetic nanoparticles, paving the way towards their clinical use.

Mixing iron oxide nanoparticles with different shape and size for tunable magneto-heating performance

Tuning the magnetic properties of nanoparticles is a strategic goal to use them in the most effective way to perform specific functions in the nanomedicine field. We report a systematic study carried out on a set of samples obtained by mixing together iron oxide nanoparticles with different shape: elongated with aspect ratio ∼5.2 and mean volume of the order of 10³ nm³ (excluding the silica coating) and spherical with mean volume one order of magnitude larger. These structural features of the nanoparticles together with their aggregation state determine the magnetic anisotropy and the magnetic relaxation processes. In particular, the spherical nanoparticles turn out to be more stable against superparamagnetic relaxation. Mixing the nanoparticles in different proportions allows to modulate the magnetic response of the samples. The two populations of nanoparticles magnetically influence each other through a mean field mechanism, which depends crucially on temperature and rules the hysteretic magnetic properties and their thermal evolution. This magnetic phenomenology has a direct impact on the ability of the mixed samples to generate heat under an alternating magnetic field, a key function in view of nanomedicine applications. Under proper testing conditions, the heating efficiency of the mixed samples is larger compared to that obtained as the sum of those of the parent nanoparticles. This occurs thanks to the mean field produced by the magnetically blocked spherical nanoparticles that stabilizes the thermally fluctuating moments of the elongated ones, which therefore contribute more effectively to the heat production.

Nanomagnetic Actuation of Hybrid Stents for Hyperthermia Treatment of Hollow Organ Tumors

This paper describes a magnetic nanotechnology that locally enables hyperthermia treatment of hollow organ tumors by using polymer hybrid stents with incorporated magnetic nanoparticles (MNP). The hybrid stents are implanted and activated in an alternating magnetic field to generate therapeutically effective heat, thereby destroying the tumor. Here, we demonstrate the feasibility of nanomagnetic actuation of three prototype hybrid stents for hyperthermia treatment of hollow organ tumors. The results show that the heating efficiency of stent filaments increases with frequency from approximately 60 W/g_Fe (95 kHz) to approximately 250 W/g_Fe (270 kHz). The same trend is observed for the variation of magnetic field amplitude; however, heating efficiency saturates at approximately 30 kA/m. MNP immobilization strongly influences heating efficiency showing a relative difference in heating output of up to 60% compared to that of freely dispersed MNP. The stents showed uniformly distributed heat on their surface reaching therapeutically effective temperatures of 43 °C and were tested in an explanted pig bile duct for their biological safety. Nanomagnetic actuation of hybrid stents opens new possibilities in cancer treatment of hollow organ tumors.

Dipolar interactions among magnetite nanoparticles for magnetic hyperthermia: a rate-equation approach

Rate equations are used to study the dynamic magnetic properties of interacting magnetite nanoparticles viewed as double well systems (DWS) subjected to a driving field in the radio-frequency range. Dipole-dipole interaction among particles is modeled by inserting an ad-hoc term in the energy barrier to simulate the dependence of the interaction on both the interparticle distance and degree of dipole collinearity. The effective magnetic power released by an assembly of interacting nanoparticles dispersed in a diamagnetic host is shown to be a complex function of nanoparticle diameter, mean particle interdistance and frequency. Dipolar interaction markedly modifies the way a host material is heated by an assembly of embedded nanoparticles in magnetic hyperthermia treatments. Nanoparticle fraction and strength of the interaction can dramatically influence the amplitude and shape of the heating curves of the host material; the heating ability of interacting nanoparticles is shown to be either improved or reduced by their concentration in the host material. A frequency-dependent cut-off length of dipolar interactions is determined and explained. Particle polydispersity entailing a distribution of particle sizes brings about non-trivial effects on the heating curves depending on the strength of dipolar interaction.

Hybrid magnetic nanoparticles as efficient nanoheaters in biomedical applications

Heating at the nanoscale is the basis of several biomedical applications, including magnetic hyperthermia therapies and heat-triggered drug delivery. The combination of multiple inorganic materials in hybrid magnetic nanoparticles provides versatile platforms to achieve an efficient heat delivery upon different external stimuli or to get an optical feedback during the process. However, the successful design and application of these nanomaterials usually require intricate synthesis routes and their magnetic response is still not fully understood. In this review we give an overview of the novel systems reported in the last few years, which have been mostly obtained by organic phase-based synthesis and epitaxial growth processes. Since the heating efficiency of hybrid magnetic nanoparticles often relies on the exchange-interaction between their components, we discuss various interface-phenomena that are responsible for their magnetic properties. Finally, followed by a brief comment on future directions in the field, we outline recent advances on multifunctional nanoparticles that can boost the heating power with light and combine heating and temperature sensing in a single nanomaterial.

Whither Magnetic Hyperthermia? A Tentative Roadmap

The scientific community has made great efforts in advancing magnetic hyperthermia for the last two decades after going through a sizeable research lapse from its establishment. All the progress made in various topics ranging from nanoparticle synthesis to biocompatibilization and in vivo testing have been seeking to push the forefront towards some new clinical trials. As many, they did not go at the expected pace. Today, fruitful international cooperation and the wisdom gain after a careful analysis of the lessons learned from seminal clinical trials allow us to have a future with better guarantees for a more definitive takeoff of this genuine nanotherapy against cancer. Deliberately giving prominence to a number of critical aspects, this opinion review offers a blend of state-of-the-art hints and glimpses into the future of the therapy, considering the expected evolution of science and technology behind magnetic hyperthermia.

Updates on the applications of iron-based nanoplatforms in tumor theranostics

With the development of biomedicine and materials science, the emerging research of iron-based nanoplatforms (INPs) have provided a bright future for tumor theranostics. Thanks to its excellent biocompatibility and diverse application potential, some INPs have successfully transformed from the laboratory to the clinic and market, making it one of the most successful nanoplatforms. Further investigations associated with its enormous biomedical potential is continuing, and new features of them are being demonstrated. The discovery of ferroptosis therapy opens up new avenue for the applications of INPs in tumor therapy, which is attracting tremendous attention from worldwide. It is well established that some of the INPs are capable of triggering the tumor cell ferroptosis efficiently, accelerating the tumor cell death process. Combined with anti-tumor drugs or other tumor therapy approaches, the INPs-induced ferroptosis are expected to break the bottleneck in the treatment of drug-resistant malignant tumors. In addition, other applications of INPs in tumor theranostics field are still active. Featured with the catalase-like ability, INPs were also well documented to reverse the tumor hypoxia as nanozymes, assisting and enhancing the oxygen-consuming tumor therapy approaches. And the unique magnetic property of INPs endow it with great potential in tumor diagnosis, hyperthermal therapy and target drug delivery. It is of great significance to summarize these new advances. Herein, the latest reports of the applications of INPs in tumor theranostics are classified to expound the trend of its research and development. The featured functions of it will be discussed in detail to provide a new insight. The key issues needing to be addressed and the development prospective will be put forward. We hope that this review will be helpful to understand the ample potential of INPs in tumor theranostics field.

Fatty Acid Remodeling of Membrane Glycerophospholipids Induced by Bleomycin and Iron Oxide Nanoparticles in Human Embryonic Kidney Cells

Bleomycin has a long-studied mechanism of action through the formation of a complex with metals, such as iron. The bleomycin-iron complex was recently shown to induce membrane damage by free radical reactivity. Because the use of Fe nanoparticles is spreading for drug delivery strategies, molecular mechanisms of cell damage must include different compartments in order to observe the progression of the cell reactivity. In this study, human embryonic kidney (HEK-293) cells were exposed for 24 h to bleomycin and polymeric iron oxide nanoparticles (Fe-NPs), alone or in combination. The fatty acid-based membrane lipidomic analysis evidenced the fatty acid remodeling in response to the treatments. Bleomycin alone caused the increase of saturated fatty acid (SFA) moieties in cell membrane glycerophospholipids with concomitant diminution of monounsaturated (MUFA) and polyunsaturated (PUFA) fatty acid levels. Under Fe-NPs treatment, omega-6 PUFA decreased and trans fatty acid isomers increased. Under coadministration bleomycin and Fe-NPs, all membrane remodeling changes disappeared compared to those of the controls, with only an increase of omega-6 PUFA that elevates peroxidation index remaining. Our results highlight the important role of fatty-acid-based membrane lipidome monitoring to follow up the fatty acid reorganization induced by the drug, to be considered as a side effect of the pharmacological activity, suggesting the need of an integrated approach for the investigation of drug and carrier molecular mechanisms.

Controlling human platelet activation with calcium-binding nanoparticles

Human platelets aggregate at sites of blood vessel damage in response to a rise in their cytosolic calcium concentration. Controlling these cytosolic calcium rises would provide a method to inhibit platelet activation and prevent the unwanted blood clots that causes heart attack and strokes. Previously we have predicted that calcium accumulation within the lumen of an infolded portion of the platelet plasma membrane called the open canalicular system (OCS) is essential for maintaining this cytosolic calcium rise. Due to its nanometer dimensions of the OCS, it has been difficult to measure or interfere with the predicted luminal calcium accumulation. Here we utilise iron oxide magnetic nanoparticles coated with the known calcium chelator, citrate, to create calcium-binding nanoparticles. These were used to assess whether an OCS calcium store plays a role in controlling the dynamics of human platelet activation and aggregation. We demonstrate that citrate-coated nanoparticles are rapidly and selectively uptaken into the OCS of activated human platelets, where they act to buffer the accumulation of calcium there. Treatment with these calcium-binding nanoparticles reduced thrombin-evoked cytosolic calcium rises, and slowed platelet aggregation and clot retraction in human platelets. In contrast, nanoparticles that cannot bind calcium have no effect. This study demonstrates that the OCS acts as a key source of calcium for maintaining cytosolic calcium rises and accelerating platelet aggregation, and that calcium-binding nanoparticles targeted to the OCS could provide an anti-platelet therapy to treat patients at risk of suffering heart attacks or strokes.

The Intracellular Number of Magnetic Nanoparticles Modulates the Apoptotic Death Pathway after Magnetic Hyperthermia Treatment

Magnetic hyperthermia is a cancer treatment based on the exposure of magnetic nanoparticles to an alternating magnetic field in order to generate local heat. In this work, 3D cell culture models were prepared to observe the effect that a different number of internalized particles had on the mechanisms of cell death triggered upon the magnetic hyperthermia treatment. Macrophages were selected by their high capacity to uptake nanoparticles. Intracellular nanoparticle concentrations up to 7.5 pg Fe/cell were measured both by elemental analysis and magnetic characterization techniques. Cell viability after the magnetic hyperthermia treatment was decreased to <25% for intracellular iron contents above 1 pg per cell. Theoretical calculations of the intracellular thermal effects that occurred during the alternating magnetic field application indicated a very low increase in the global cell temperature. Different apoptotic routes were triggered depending on the number of internalized particles. At low intracellular magnetic nanoparticle amounts (below 1 pg Fe/cell), the intrinsic route was the main mechanism to induce apoptosis, as observed by the high Bax/Bcl-2 mRNA ratio and low caspase-8 activity. In contrast, at higher concentrations of internalized magnetic nanoparticles (1-7.5 pg Fe/cell), the extrinsic route was observed through the increased activity of caspase-8. Nevertheless, both mechanisms may coexist at intermediate iron concentrations. Knowledge on the different mechanisms of cell death triggered after the magnetic hyperthermia treatment is fundamental to understand the biological events activated by this procedure and their role in its effectiveness.

Hadron Therapy, Magnetic Nanoparticles and Hyperthermia: A Promising Combined Tool for Pancreatic Cancer Treatment

A combination of carbon ions/photons irradiation and hyperthermia as a novel therapeutic approach for the in-vitro treatment of pancreatic cancer BxPC3 cells is presented. The radiation doses used are 0–2 Gy for carbon ions and 0–7 Gy for 6 MV photons. Hyperthermia is realized via a standard heating bath, assisted by magnetic fluid hyperthermia (MFH) that utilizes magnetic nanoparticles (MNPs) exposed to an alternating magnetic field of amplitude 19.5 mTesla and frequency 109.8 kHz. Starting from 37 °C, the temperature is gradually increased and the sample is kept at 42 °C for 30 min. For MFH, MNPs with a mean diameter of 19 nm and specific absorption rate of 110 ± 30 W/g_Fe3o₄ coated with a biocompatible ligand to ensure stability in physiological media are used. Irradiation diminishes the clonogenic survival at an extent that depends on the radiation type, and its decrease is amplified both by the MNPs cellular uptake and the hyperthermia protocol. Significant increases in DNA double-strand breaks at 6 h are observed in samples exposed to MNP uptake, treated with 0.75 Gy carbon-ion irradiation and hyperthermia. The proposed experimental protocol, based on the combination of hadron irradiation and hyperthermia, represents a first step towards an innovative clinical option for pancreatic cancer.

Altering model cell membranes by means of localized magnetic heating

Isolated iron oxide magnetic nanoparticles (MNPs), 12 nm in diameter, coated with oleic acid molecules as capping agents have been deposited by the Langmuir-Blodgett (LB) method onto a model cell membrane incorporating 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC) and Cholesterol (Chol) in the 1:1 ratio, which was also fabricated by the LB technique. Atomic Force Microscopy (AFM) experiments showed that the application of an alternating magnetic field results in the embedding of the MNPs through the phospholipidic layer. These experimental results reveal that the heating of individual MNPs may induce a local increase in the fluidity of the film with a large control of the spatial and temporal specificity.

Exploring the potential of the dynamic hysteresis loops via high field, high frequency and temperature adjustable AC magnetometer for magnetic hyperthermia characterization

AIM

The Specific Absorption Rate (SAR) is the key parameter to optimize the effectiveness of magnetic nanoparticles in magnetic hyperthermia. AC magnetometry arises as a powerful technique to quantify the SAR by computing the hysteresis loops' area. However, currently available devices produce quite limited magnetic field intensities, below 45mT, which are often insufficient to obtain major hysteresis loops and so a more complete and understandable magneticcharacterization. This limitation leads to a lack of information concerning some basic properties, like the maximum attainable (SAR) as a function of particles' size and excitation frequencies, or the role of the mechanical rotation in liquid samples.

METHODS

To fill this gap, we have developed a versatile high field AC magnetometer, capable of working at a wide range of magnetic hyperthermia frequencies (100 kHz - 1MHz) and up to field intensities of 90mT. Additionally, our device incorporates a variable temperature system for continuous measurements between 220 and 380 K. We have optimized the geometrical properties of the induction coil that maximize the generated magnetic field intensity.

RESULTS

To illustrate the potency of our device, we present and model a series of measurements performed in liquid and frozen solutions of magnetic particles with sizes ranging from 16 to 29 nm.

CONCLUSION

We show that AC magnetometry becomes a very reliable technique to determine the effective anisotropy constant of single domains, to study the impact of the mechanical orientation in the SAR and to choose the optimal excitation parameters to maximize heating production under human safety limits.

Iron Oxide Mediated Photothermal Therapy in the Second Biological Window: A Comparative Study between Magnetite/Maghemite Nanospheres and Nanoflowers

The photothermal use of iron oxide magnetic nanoparticles (NPs) is becoming more and more popular and documented. Herein, we compared the photothermal (PT) therapy potential versus magnetic hyperthermia (MHT) modality of magnetic nanospheres, largely used in the biomedical field and magnetic multicore nanoflowers known among the best nanoheaters. The NPs were imaged using transmission electron microscopy and their optical properties characterized by UV-Vis-NIR-I-II before oxidation (magnetite) and after oxidation to maghemite. The efficiency of all NPs in MHT and PT in the preferred second near-infrared (NIR-II) biological window was carried out in water and in cancer cells. We show that, in water, magnetite nanoflowers are the most efficient nanoheaters for both modalities. Moreover, PT appears much more efficient than MHT at low NP dose, whatever the NP. In the cellular environment, for PT, efficiency was totally conserved, with magnetite nanoflowers as the best performers compared to MHT, which was totally lost. Finally, cell uptake was significantly increased for the nanoflowers compared to the nanospheres. Finally, the antitumor therapy was investigated for all NPs at the same dose delivered to the cancer cells and at reasonable laser power density (0.3 W/cm²), which showed almost total cell death for magnetite nanoflowers.

Shell-mediated control of surface chemistry of highly stoichiometric magnetite nanoparticles

Magnetite (Fe3O4) nanoparticles are one of the most studied nanomaterials for different nanotechnological and biomedical applications. However, Fe3O4 nanomaterials gradually oxidize to maghemite (γ-Fe2O3) under conventional environmental conditions leading to changes in their functional properties that determine their performance in many applications. Here we propose a novel strategy to control the surface chemistry of monodisperse 12 nm magnetite nanoparticles by means of a 3 nm-thick Zn-ferrite epitaxial coating in core/shell nanostructures. We have carried out a combined Mössbauer spectroscopy, dc magnetometry, X-ray photoelectron spectroscopy and spatially resolved electron energy loss spectroscopy study on iron oxide and Fe3O4/Zn0.6Fe2.4O4 core/shell nanoparticles aged under ambient conditions for 6 months. Our results reveal that while the aged iron oxide nanoparticles consist of a mixture of γ-Fe2O3 and Fe3O4, the Zn-ferrite-coating preserves a highly stoichiometric Fe3O4 core. Therefore, the aged core/shell nanoparticles present a sharp Verwey transition, an increased saturation magnetization and the possibility of tuning the effective anisotropy through exchange-coupling at the core/shell interface. The inhibition of the oxidation of the Fe3O4 cores can be accounted for in terms of the chemical nature of the shell layer and an epitaxial crystal symmetry matching between the core and the shell.

Highly Reproducible Hyperthermia Response in Water, Agar, and Cellular Environment by Discretely PEGylated Magnetite Nanoparticles

Local heat generation from magnetic nanoparticles (MNPs) exposed to alternating magnetic fields can revolutionize cancer treatment. However, the application of MNPs as anticancer agents is limited by serious drawbacks. Foremost among these are the fast uptake and biodegradation of MNPs by cells and the unpredictable magnetic behavior of the MNPs when they accumulate within or around cells and tissues. In fact, several studies have reported that the heating power of MNPs is severely reduced in the cellular environment, probably due to a combination of increased viscosity and strong NP agglomeration. Herein, we present an optimized protocol to coat magnetite (Fe₃O₄) NPs larger than 20 nm (FM-NPs) with high molecular weight PEG molecules that avoid collective coatings, prevent the formation of large clusters of NPs and keep constant their high heating performance in environments with very different ionic strengths and viscosities (distilled water, physiological solutions, agar and cell culture media). The great reproducibility and reliability of the heating capacity of this FM-NP@PEG system in such different environments has been confirmed by AC magnetometry and by more conventional calorimetric measurements. The explanation of this behavior has been shown to lie in preserving as much as possible the magnetic single domain-type behavior of nearly isolated NPs. In vitro endocytosis experiments in a colon cancer-derived cell line indicate that FM-NP@PEG formulations with PEGs of higher molecular weight (20 kDa) are more resistant to endocytosis than formulations with smaller PEGs (5 kDa), showing quite large uptake mean-life (τ > 5 h) in comparison with other NP systems. The in vitro magnetic hyperthermia was performed at 21 mT and 650 kHz during 1 h in a pre-endocytosis stage and complete cell death was achieved 48 h posthyperthermia. These optimal FM-NP@PEG formulations with high resistance to endocytosis and predictable magnetic response will aid the progress and accuracy of the emerging era of theranostics.

Zn- and (Mn, Zn)-substituted versus unsubstituted magnetite nanoparticles: structural, magnetic and hyperthermic properties

In this work, we studied structural and magnetic properties of 18 nm sized Zn-substituted magnetite, 28 nm sized unsubstituted and 17 nm sized (Mn, Zn)-substituted iron oxide nanoparticles, synthesized by thermal decomposition method. Their features were examined by analyzing the x-ray diffraction data, ⁵⁷Fe Mössbauer spectra and magnetization measurements by SQUID interferometer. The microstructure was inspected comparing the different size and strain broadening models incorporated into Fullprof software. In terms of crystallinity and size dispersion, applied synthesis protocol shows superiority over decomposition of iron oleate and the co-precipitation synthesis route. The saturation magnetization at T = 5 K was found to be within the M _S = 91.2-98.6 A m² kg^-1 range, while at 300 K M _S of pure and Zn-substituted Fe₃O₄ nanoparticles is 83.6 and 86.2 A m² kg^-1, respectively. Effective magnetic anisotropy constant K _eff, estimated under slow measurements by SQUID, is below 20 kJ m^-3 in all three samples. Some preliminary measurements of the magnetic hyperthermia performance, expressed via specific absorption rate value showed that the best heating performances were displayed by 18 nm sized oleic acid-coated Zn_0.13Fe_2.87O₄ cubo-octahedrons with SAR ≅ 425 W/g_Fe at H ₀ = 20 kA m^-1 and f = 228 kHz.

Sedimentation Kinetics of Magnetic Nanoparticle Clusters: Iron Oxide Nanospheres vs Nanorods

A detailed study of the sedimentation kinetics of iron oxide nanoparticle (IONP) clusters composed of nanospheres and nanorods is presented. Measurements were performed to determine the absorbance of an IONP suspension undergoing sedimentation over time by using a UV-vis spectrophotometer with simultaneous monitoring of the hydrodynamic diameter of the clusters formed with dynamic light scattering (DLS). Mathematical analysis based on Happel's spherical and cylindrical models was conducted to reveal the relationship between the settling velocity of the IONP clusters and their packing density. For the case of IONP clusters composed of rodlike particles, two distinctive phases of sedimentation were recorded, with the occurrence of rapid sedimentation at the beginning of the process (phase I) followed by a slower settling rate (phase II). In sedimentation phase II, even though the nanorod clusters had a hydrodynamic size of >500 nm, which was much larger than that of the nanosphere clusters (∼200 nm), their settling velocity of 0.0038 mm/min was still slower than that of the nanosphere clusters. Such observations were mainly a result of the packing density differences between the formed clusters; due to the end-to-end particle interactions of nanorods, the nanorod clusters were less tightly packed and more permeable. In addition to the mathematical analysis, quartz crystal microbalance with dissipation (QCM-D) was employed to measure the "softness" of the IONP clusters formed, and this physical property can be further related to their packing density. This study illustrated that for a rapidly aggregating system, such as magnetic IONPs, not only do the particle shape and size uniformity contribute to the physical properties of the particle clusters formed but also the nature of the aggregation, either end-to-end and/or side-to-side, should be carefully considered when designing a colloidally stable IONP suspension.

Janus Magnetic-Plasmonic Nanoparticles for Magnetically Guided and Thermally Activated Cancer Therapy

Progress of thermal tumor therapies and their translation into clinical practice are limited by insufficient nanoparticle concentration to release therapeutic heating at the tumor site after systemic administration. Herein, the use of Janus magneto-plasmonic nanoparticles, made of gold nanostars and iron oxide nanospheres, as efficient therapeutic nanoheaters whose on-site delivery can be improved by magnetic targeting, is proposed. Single and combined magneto- and photo-thermal heating properties of Janus nanoparticles render them as compelling heating elements, depending on the nanoparticle dose, magnetic lobe size, and milieu conditions. In cancer cells, a much more effective effect is observed for photothermia compared to magnetic hyperthermia, while combination of the two modalities into a magneto-photothermal treatment results in a synergistic cytotoxic effect in vitro. The high potential of the Janus nanoparticles for magnetic guiding confirms them to be excellent nanostructures for in vivo magnetically enhanced photothermal therapy, leading to efficient tumor growth inhibition.

S, Prakash P, Nishad KV, Komath M, Nair BN, G. S. S. Amino acid inspired tunable superparamagnetic iron oxide (SPION) nanostructures with high magnetic hyperthermia potential for biofunctional applications

Amino acid inspired biocompatible and tunable magnetic SPION nanostructures with high saturation magnetization hyperthermia and biofunctional probe potential are shown.

The cell uptake properties and hyperthermia performance of Zn0.5Fe2.5O4/SiO2 nanoparticles as magnetic hyperthermia agents

Zn0.5Fe2.5O4 nanoparticles (NPs) of 22 nm are synthesized by a one-pot approach and coated with silica for magnetic hyperthermia agents. The NPs exhibit superparamagnetic characteristics, high-specific absorption rate (SAR) (1083 wg-1, f = 430 kHz, H = 27 kAm-1), large saturation magnetization (M s = 85 emu g-1), excellent colloidal stability and low cytotoxicity. The cell uptake properties have been investigated by Prussian blue staining, transmission electron microscopy and the inductively coupled plasma-mass spectrometer, which resulted in time-dependent and concentration-dependent internalization. The internalization appeared between 0.5 and 2 h, the NPs were mainly located in the lysosomes and kept in good dispersion after incubation with human osteosarcoma MG-63 cells. Then, the relationship between cell uptake and magnetic hyperthermia performance was studied. Our results show that the hyperthermia efficiency was related to the amount of internalized NPs in the tumour cells, which was dependent on the concentration and incubation time. Interestingly, the NPs could still induce tumour cells to apoptosis/necrosis when extracellular NPs were rinsed, but the cell kill efficiency was lower than that of any rinse group, which indicated that local temperature rise was the main factor that induced tumour cells to death. Our findings suggest that this high SAR and biocompatible silica-coated Zn0.5Fe2.O4 NPs could serve as new agents for magnetic hyperthermia.

Programmable Ultralight Magnets via Orientational Arrangement of Ferromagnetic Nanoparticles within Aerogel Hosts

The actuation and levitation of air-suspended objects by a magnetic field, due to its noncontact and holonomic manipulation modes, are important technological capabilities for device applications. However, owing to a higher density of conventional ferromagnets or nanoparticle-containing polymers and strong magnetic fields required for actuation, fabricating lightweight materials with a sensitive magnetic response for weight critical applications is challenging. Here, we report ultralight aerogel-based magnets (aero-magnets) comprising assembled ferromagnetic nanomaterials with highly magnetic anisotropy where the magnetic domains can be programmed by external predesigned fields. To demonstrate the breadth of manufacturing methods for this breed of aero-magnet composites, both silica/nanocellulose aerogel hosts and ferromagnetic nanorod/nanoplatelet guests have been explored. Single and double domains with out-of-plane magnetization are programmed into the aero-magnets and characterized by magnetic force microscopy. The levitation and actuation of the aero-magnets are realized while exposed to a small external magnetic field of 11 mT and introduced to a switching circuit. Furthermore, the elastic moduli of the aero-magnets are estimated by dynamic magnetic responses of the ferromagnetic nanoparticles tightly tethered in the aerogel hosts under rapid cyclic fields. These programmable aero-magnets could serve as monolithic magnetic actuator units in the fields of tiny robots and aerospace components.

Confining Iron Oxide Nanocubes inside Submicrometric Cavities as a Key Strategy To Preserve Magnetic Heat Losses in an Intracellular Environment

The design of magnetic nanostructures whose magnetic heating efficiency remains unaffected at the tumor site is a fundamental requirement to further advance magnetic hyperthermia in the clinic. This work demonstrates that the confinement of magnetic nanoparticles (NPs) into a sub-micrometer cavity is a key strategy to enable a certain degree of nanoparticle motion and minimize aggregation effects, consequently preserving the magnetic heat loss of iron oxide nanocubes (IONCs) under different conditions, including intracellular environments. We fabricated magnetic layer-by-layer (LbL) self-assembled polyelectrolyte sub-micrometer capsules using three different approaches, and we studied their heating efficiency as obtained in aqueous dispersions and after internalization by tumor cells. First, IONCs were added to the hollow cavities of LbL submicrocapsules, allowing the IONCs to move to a certain extent in the capsule cavities. Second, IONCs were coencapsulated into solid calcium carbonate cores coated with LbL polymer shells. Third, IONCs were incorporated within the polymer layers of the LbL capsule walls. In aqueous solution, higher specific absorption rate (SAR) values were related to those of free IONCs, while lower SAR values were recorded for capsule/core assemblies. However, after uptake by cancer cell lines (SKOV-3 cells), the SAR values of the free IONCs were significantly lower than those observed for capsule/core assemblies, especially after prolonged incubation periods (24 and 48 h). These results show that IONCs packed into submicrocavities preserve the magnetic losses, as the SAR values remained almost invariable. Conversely, free IONCs without the protective capsule shell agglomerated and their magnetic losses were strongly reduced. Indeed, IONC-loaded capsules and free IONCs reside inside endosomal and lysosomal compartments after cellular uptake and show strongly reduced magnetic losses due to the immobilization and aggregation in centrosymmetrical structures in the intracellular vesicles. The confinement of IONCs into sub-micrometer cavities is a key strategy to provide a sustained and predictable heating dose inside biological matrices.

Cancer cell membrane-coated mesoporous silica loaded with superparamagnetic ferroferric oxide and Paclitaxel for the combination of Chemo/Magnetocaloric therapy on MDA-MB-231 cells

To effectively inhibit the growth of breast cancer cells (MDA-MB-231 cells) by the combination method of chemotherapy and magnetic hyperthermia, we fabricated a biomimetic drug delivery (CSiFePNs) system composed of mesoporous silica nanoparticles (MSNs) containing superparamagnetic ferroferric oxide and Paclitaxel (PTX) coated with MDA-MB-231 cell membranes (CMs). In the in vitro cytotoxicity tests, the MDA-MB-231 cells incubated with CSiFePNs obtained IC50 value of 0.8 μgL-1, 3.5-fold higher than that of SiFePNs. The combination method of chemotherapy and magnetic hyperthermia can effectively inhibit the growth of MDA-MB-231 cells.

Autodegradable clusters made from superparamagnetic nanoparticles with drug-release properties

Aim: The agglomeration of nanoparticles plays an important role in the preparation of nanostructured materials, which has implications in their practical applications such as plasma nanosensor and drug release. Materials & methods: Highly stable individual superparamagnetic γ-Fe₂O₃ nanoparticles with diameter of 5 nm were first synthesized in water. These particles were then assembled into spherical clusters with diameters of approximately 200 nm using a simple and versatile method. Results: The prepared γ-Fe₂O₃ nanoparticle-based clusters were then used for aminophylline drug loading and release properties investigation. The results show the high drug load rate, release speed and release rate. Conclusion: The present materials and method present great potential in drug-release application.

Esterase-Cleavable 2D Assemblies of Magnetic Iron Oxide Nanocubes: Exploiting Enzymatic Polymer Disassembling To Improve Magnetic Hyperthermia Heat Losses

Here, we report a nanoplatform based on iron oxide nanocubes (IONCs) coated with a bioresorbable polymer that, upon exposure to lytic enzymes, can be disassembled increasing the heat performances in comparison with the initial clusters. We have developed two-dimensional (2D) clusters by exploiting benchmark IONCs as heat mediators for magnetic hyperthermia and a polyhydroxyalkanoate (PHA) copolymer, a biodegradable polymer produced by bacteria that can be digested by intracellular esterase enzymes. The comparison of magnetic heat performance of the 2D assemblies with 3D centrosymmetrical assemblies or single IONCs emphasizes the benefit of the 2D assembly. Moreover, the heat losses of 2D assemblies dispersed in water are better than the 3D assemblies but worse than for single nanocubes. On the other hand, when the 2D magnetic beads (2D-MNBs) are incubated with the esterase enzyme at a physiological temperature, their magnetic heat performances began to progressively increase. After 2 h of incubation, specific absorption rate values of the 2D assembly double the ones of individually coated nanocubes. Such an increase can be mainly correlated to the splitting of the 2D-MNBs into smaller size clusters with a chain-like configuration containing few nanocubes. Moreover, 2D-MNBs exhibited nonvariable heat performances even after intentionally inducing their aggregation. Magnetophoresis measurements indicate a comparable response of 3D and 2D clusters to external magnets (0.3 T) that is by far faster than that of single nanocubes. This feature is crucial for a physical accumulation of magnetic materials in the presence of magnetic field gradients. This system is the first example of a nanoplatform that, upon exposure to lytic enzymes, such as those present in a tumor environment, can be disassembled from the initial 2D-MNB organization to chain-like assemblies with clear improvement of the heat magnetic losses resulting in better heat dissipation performances. The potential application of 2D nanoassemblies based on the cleavable PHAs for preserving their magnetic losses inside cells will benefit hyperthermia therapies mediated by magnetic nanoparticles under alternating magnetic fields.

Polymeric Reactor for the Synthesis of Superparamagnetic-Thermal Treatment of Breast Cancer

Engineered superparamagnetic iron oxide nanoparticles (SPIONs) have been studied extensively for their localized homogeneous heat generation in breast cancer therapy. However, challenges such as aggregation and inability to produce sub-10 nm SPIONs limit their potential in magnetothermal ablation. We report a facile, efficient, and robust in situ method for the synthesis of SPIONs within a poly(ethylene glycol) (PEG) reactor adsorbed onto reduced graphene oxide nanosheets (rGO) via the microwave hydrothermal route. This promising modality yields crystalline, stable, biocompatible, and superparamagnetic PEGylated SPION-rGO nanocomposites (NCs) with uniform dispersibility. Our findings show that rGO acts as a breeding ground for the spatially distributed nanosites around which the ferrihydrite seeds accumulate to ultimately transform into immobilized SPIONs. PEG, in parallel, acts as a critical confining agent physically trapping the accumulated seeds to prevent their aggregation and create multiple domains on rGO for the synthesis of quantum-sized SPIONs (9 ± 1 nm in diameter). This dual functionality (rGO and PEG) exhibits a pronounced effect on reducing both the aggregation and the sizes of fabricated SPIONs as confirmed by the scanning transmission electron microscopy images, dynamic light scattering analyses, and the specific absorption rates (SARs). Reduced aggregation lowered the toxicity of NCs, where PEGylated SPION-rGO NCs are more biocompatible than PEGylated SPIONs, showing no significant induction of cell apoptosis, mitochondrial membrane injury, or oxidative stress. Significantly less lactate dehydrogenase release and hence less necrosis are observed after 48 h exposure to high doses of PEGylated SPION-rGO NCs compared with PEGylated SPIONs. NCs induce local heat generation with a SAR value of 1760 ± 97 W/g, reaching up to 43 ± 0.3 °C and causing significant MCF-7 breast tumor cell ablation of about 78 ± 10% upon applying an external magnetic field. Collectively, rGO and PEG functionalities have a synergistic effect on improving the synthesis, stability, biocompatibility, and magnetothermal properties of SPIONs.

Cell-Promoted Nanoparticle Aggregation Decreases Nanoparticle-Induced Hyperthermia under an Alternating Magnetic Field Independently of Nanoparticle Coating, Core Size, and Subcellular Localization

Magnetic hyperthermia has a significant potential to be a new breakthrough for cancer treatment. The simple concept of nanoparticle-induced heating by the application of an alternating magnetic field has attracted much attention, as it allows the local heating of cancer cells, which are considered more susceptible to hyperthermia than healthy cells, while avoiding the side effects of traditional hyperthermia. Despite the potential of this therapeutic approach, the idea that local heating effects due to the application of alternating magnetic fields on magnetic nanoparticle-loaded cancer cells can be used as a treatment is controversial. Several studies indicate that the heating capacity of magnetic nanoparticles is largely reduced in the cellular environment because of increased viscosity, aggregation, and dipolar interactions. However, an increasing number of studies, both in vitro and in vivo, show evidence of successful magnetic hyperthermia treatment on several different types of cancer cells. This apparent contradiction might be due to the use of different experimental conditions. Here, we analyze the effects of several parameters on the cytotoxic efficiency of magnetic nanoparticles as heat inductors under an alternating magnetic field. Our results indicate that the cell-nanoparticle interaction reduces the cytotoxic effects of magnetic hyperthermia, independent of nanoparticle coating and core size, the cell line used, and the subcellular localization of nanoparticles. However, there seems to occur a synergistic effect between the application of an external source of heat and the presence of magnetic nanoparticles, leading to higher toxicities than those induced by heat alone or the accumulation of nanoparticles within cells.

A fluorescent method based on magnetic nanoparticles for detection of CGG trinucleotide repeat genes

A novel fluorescent sensor based on magnetic nanoparticles as the separator and short report DNA was designed and prepared for the detection of d(CGG)_ntrinucleotide repeats. The method exhibited high selectivity and sensitivity, and excellent linear correlation from 100 pM to 150 nM, which is useful for the early diagnosis of neurodegenerative diseases.

Multilayered inorganic-organic microdisks as ideal carriers for high magnetothermal actuation: assembling ferrimagnetic nanoparticles devoid of dipolar interactions

The two major limitations for nanoparticle based magnetic hyperthermia in theranostics are the delivery of a sufficient number of magnetic nanoparticles (MNPs) with high heating power to specific target cells and the residence time of the MNPs at the target location. Ferromagnetic or Ferrimagnetic single domain nanoparticles (F-MNPs), with a permanent magnetic dipole, produce larger magnetic and thermal responses than superparamagnetic nanoparticles (SP-MNPs) but also agglomerate more. MNP agglomeration degrades their heating potential due to dipolar interaction effects and interferes with specific targeting. Additionally, MNPs bound to cells are often endocytosed by the cells or, in vivo, cleared out by the immune system via uptake in macrophages. Here, we present a versatile approach to engineer inorganic-polymeric microdisks, loaded with biomolecules, fluorophores and Fe3O4 F-MNPs that solves both challenges. These microdisks deliver the F-MNPs efficiently, while controlling any undesirable agglomeration and dipolar interaction, while also rendering the F-MNPs endocytosis resistant. We show that these micro-devices are suitable carriers to transport a flat assembly of F-MNPs to the cell membrane unchanged, preserving the magnetic response of the MNPs in any biological environment. The F-MNPs concentration per microdisk and degree of MNP interaction are tunable. We demonstrate that the local heat generated in microdisks is proportional to the surface density of F-MNPs when attached to the cell membrane. The key innovation in the production of these microdisks is the fabrication of a mushroom-shaped photolithographic template that enables easy assembly of the inorganic film, polymeric multilayers, and MNP cargo while permitting highly efficient lift-off of the completed microdisks. During the harvesting of the flat microdisks, the supporting mushroom-shaped templates are sacrificed. These resulting magnetic hybrid microdisks are tunable and efficient devices for magnetothermal actuation and hyperthermia.

High Frequency Hysteresis Losses on γ-Fe₂O₃ and Fe₃O₄: Susceptibility as a Magnetic Stamp for Chain Formation

In order to understand the properties involved in the heating performance of magnetic nanoparticles during hyperthermia treatments, a systematic study of different γ-Fe₂O₃ and Fe₃O₄ nanoparticles has been done. High-frequency hysteresis loops at 50 kHz carried out on particles with sizes ranging from 6 to 350 nm show susceptibility χ increases from 9 to 40 for large particles and it is almost field independent for the smaller ones. This suggests that the applied field induces chain ordering in large particles but not in the smaller ones due to the competition between thermal and dipolar energy. The specific absorption rate (SAR) calculated from hysteresis losses at 60 mT and 50 kHz ranges from 30 to 360 W/g_Fe, depending on particle size, and the highest values correspond to particles ordered in chains. This enhanced heating efficiency is not a consequence of the intrinsic properties like saturation magnetization or anisotropy field but to the spatial arrangement of the particles.

Fe2+ Deficiencies, FeO Subdomains, and Structural Defects Favor Magnetic Hyperthermia Performance of Iron Oxide Nanocubes into Intracellular Environment

Herein, by studying a stepwise phase transformation of 23 nm FeO-Fe₃O₄ core-shell nanocubes into Fe₃O₄, we identify a composition at which the magnetic heating performance of the nanocubes is not affected by the medium viscosity and aggregation. Structural and magnetic characterizations reveal the transformation of the FeO-Fe₃O₄ nanocubes from having stoichiometric phase compositions into Fe²⁺-deficient Fe₃O₄ phases. The resultant nanocubes contain tiny compressed and randomly distributed FeO subdomains as well as structural defects. This phase transformation causes a 10-fold increase in the magnetic losses of the nanocubes, which remain exceptionally insensitive to the medium viscosity as well as aggregation unlike similarly sized single-phase magnetite nanocubes. We observe that the dominant relaxation mechanism switches from Néel in fresh core-shell nanocubes to Brownian in partially oxidized nanocubes and once again to Néel in completely treated nanocubes. The Fe²⁺ deficiencies and structural defects appear to reduce the magnetic energy barrier and anisotropy field, thereby driving the overall relaxation into Néel process. The magnetic losses of these nanoparticles remain unchanged through a progressive internalization/association to ovarian cancer cells. Moreover, the particles induce a significant cell death after being exposed to hyperthermia treatment. Here, we present the largest heating performance that has been reported to date for 23 nm iron oxide nanoparticles under intracellular conditions. Our findings clearly demonstrate the positive impacts of the Fe²⁺ deficiencies and structural defects in the Fe₃O₄ structure on the heating performance into intracellular environment.

Shaping iron oxide nanocrystals for magnetic separation applications

Iron oxide nanostructures are attractive for a variety of bio-related applications given their wide range of magnetic properties. Here, we report on the study of the magnetophoretic mobility of octapod-shaped nanocrystals, which we relate to stoichiometry, quality and elongation in the 111 direction of these cubic structures. This special morphology combines magnetocrystalline anisotropies, increases shape anisotropy and hinders the formation of an epitaxial wüstite-magnetite interface. As a result, one obtains nanocrystals with large magnetic susceptibility and small coercivity, that is, with optimum characteristics for magnetic guidance, separation, and drug delivery, due to the increased magnetophoretic mobility displayed.

Influence of medium viscosity and intracellular environment on the magnetization of superparamagnetic nanoparticles in silk fibroin solutions and 3T3 mouse fibroblast cell cultures

Biomedical applications based on the magnetic properties of superparamagnetic iron oxide nanoparticles (SPIONs) may be altered by the mechanical attachment or cellular uptake of these nanoparticles. When nanoparticles interact with living cells, they are captured and internalized into intracellular compartments. Consequently, the magnetic behavior of the nanoparticles is modified. In this paper, we investigated the change in the magnetic response of 14 nm magnetic nanoparticles (Fe₃O₄) in different solutions, both as a stable liquid suspension (one of them mimicking the cellular cytoplasm) and when associated with cells. The field-dependent magnetization curves from inert fluids and cell cultures were determined by using an alternating gradient magnetometer, MicroMagTM 2900. The equipment was adapted to measure liquid samples because it was originally designed only for solids. In order to achieve this goal, custom sample holders were manufactured. Likewise, the nuclear magnetic relaxation dispersion profiles for the inert fluid were also measured by fast field cycling nuclear magnetic relaxation relaxometry. The results show that SPION magnetization in inert fluids was affected by the carrier liquid viscosity and the concentration. In cell cultures, the mechanical attachment or confinement of the SPIONs inside the cells accounted for the change in the dynamic magnetic behavior of the nanoparticles. Nevertheless, the magnetization value in the cell cultures was slightly lower than that of the fluid simulating the viscosity of cytoplasm, suggesting that magnetization loss was not only due to medium viscosity but also to a reduction in the mechanical degrees of freedom of SPIONs rotation and translation inside cells. The findings presented here provide information on the loss of magnetic properties when nanoparticles are suspended in viscous fluids or internalized in cells. This information could be exploited to improve biomedical applications based on magnetic properties such as magnetic hyperthermia, contrast agents and drug delivery.

Rod-shaped mesoporous silica nanoparticles for nanomedicine: recent progress and perspectives

INTRODUCTION

Interest in mesoporous silica nanoparticles for drug delivery has resulted in a good understanding of the impact of size and surface chemistry of these nanoparticles on their performance as drug carriers. Shape has emerged as an additional factor that can have a significant effect on delivery efficacy. Rod-shaped mesoporous silica nanoparticles show improvements in drug delivery relative to spherical mesoporous silica nanoparticles.

AREAS COVERED

This review summarises the synthesis methods for producing rod-shaped mesoporous silica nanoparticles for use in nanomedicine. The second part covers recent progress of mesoporous silica nanorods by comparing the impact of sphere and rod-shape on drug delivery efficiency.

EXPERT OPINION

As hollow mesoporous silica nanorods are capable of higher drug loads than most other drug delivery vehicles, such particles will reduce the amount of mesoporous silica in the body for efficient therapy. However, the importance of nanoparticle shape on drug delivery efficiency is not well understood for mesoporous silica. Studies that visualize and quantify the uptake pathway of mesoporous silica nanorods in specific cell types and compare the cellular uptake to the well-studied nanospheres should be the focus of research to better understand the role of shape in uptake.