Synergy of low-energy {101} and high-energy {001} TiO₂ crystal facets for enhanced photocatalysis

Recent developments and challenges in practical application of visible-light-driven TiO2-based heterojunctions for PPCP degradation: A critical review

The ability of the TiO₂-based photocatalysis process to mineralize organic pollutants has attracted attention worldwide for the degradation of recalcitrant pharmaceuticals and personal care products (PPCPs). Nevertheless, (1) the limited exploitation of the solar spectrum, i.e., activation under UV light (only 2-3% of solar spectrum), and (2) the high recombination rate of photo-generated charge carriers, i.e., electrons and holes, have limited its application which can, however, be improved by developing a TiO₂-based heterojunction. The objective of this critical review paper is to discuss the recent developments (2009-2019) in visible-light-driven (VLD) TiO₂-based heterojunctions for PPCP degradation and their degradation mechanisms. Compared to the conventional heterojunctions, Schottky and Z-scheme heterojunctions, which are non-conventional heterojunctions, are found to be more effective for PPCP degradation due to their more efficient separation of charge carriers and the occurrence of redox reactions at a relatively higher redox potential. Furthermore, the enhancement strategies for the development of a VLD TiO₂-based heterojunction are also explored which can be achieved by selecting the (1) highly photocatalytically active {001} facet of anatase TiO₂, (2) synthesis methods governing the structural changes at the junction interface, and (3) heterojunction components which can efficiently generate the powerful •OH radicals. The challenges in practical applications are also discussed which include factors, viz., cost reduction, recycling, stability, byproducts analysis, evaluation of the environmental effectiveness, and reactor design and scale-up of the VLD TiO₂-based heterojunctions. Accordingly, the prospects of VLD TiO₂-based heterojunctions for PPCP degradation in real environmental applications are discussed.

Catalytic Reclamation of Silver Present in Photographic Waste Using Magnetically Separable TiO2@CuFe2O4 Nanocomposites and Thereof Its Use in Antibacterial Activity

In the present investigation, the silver present in photographic waste is reclaimed catalytically using magnetically separable TiO₂@CuFe₂O₄ nanocomposites (NCs), and further, the recovered silver nanoparticles [Ag(0) NPs] are tested against the representative bacteria for the antibacterial activity. Initially, a series of the different composites between TiO₂ nanoparticles and CuFe₂O₄ nanoparticles are synthesized by a sol-gel "ex situ" method to enhance the catalytic activity of bare nanomaterials toward the visible region of the electromagnetic spectrum. X-ray diffraction reveals the presence of characteristic patterns for the tetragonal structure in the bare materials or TiO₂@CuFe₂O₄ NCs; however, the dominance in the phase as well as intensity of the respective XRD reflections in the NCs is observed according to the content of TiO₂ or CuFe₂O₄ in the NCs. Field-emission electron microscopic images show the uniform spherical particles for the representative TiO₂@CuFe₂O₄ NCs, which is also confirmed through the HRTEM images. The magnetically separable behavior of the representative TiO₂@CuFe₂O₄ NCs is confirmed through the VSM measurements, which also shows the superparamagnetic properties due to the S-shaped nature of the hysteresis loop. Thereafter, a photoconversion reaction of Ag(I) ions to Ag(0) NPs as a model reaction is carried out using the different TiO₂@CuFe₂O₄ NCs under visible light irradiation, and hence, the higher catalytic recovery of Ag(0) NPs is observed for a composite containing 10 wt % TiO₂ and 90 wt % CuFe₂O₄ than that of other NCs or the bare one alone. The optimized protocol of the model reaction is adopted for reclaiming Ag(0) NPs from photographic waste. The progress of the catalytic reclamation reaction is monitored using UV-visible, and then sizes of the recovered Ag(0) NPs are confirmed through the HRTEM images. Thereafter, the recovered Ag(0) NPs are tested for complete photoinactivation of Escherichia coli bacteria within 120 min.

g-C3N4/TiO2 composite microspheres: in situ growth and high visible light catalytic activity

The g-C₃N₄/TiO₂ heterojunction, possessing a 3D flower-like self-assembled morphology, realizing excellent visible-light photocatalytic properties, is a photocatalyst for wastewater treatment or a photoanode for photoelectrochemical water splitting.

Enhanced photocatalytic activity of anatase by the rational modification of the {001} facets with Fe(iii) ions

Fe(iii) ion-modified TiO₂ exhibits the highest reaction efficiency for the decomposition of dye molecules and p-chlorophenol due to electron-trapping centers.

Three-dimensional morphology of anatase nanocrystals obtained from supercritical flow synthesis with industrial grade TiOSO4 precursor

Anatase TiO2 (a-TiO2) nanocrystals are vital in catalytic applications both as catalysts (e.g. photodegradation) and as a carrier material (e.g. NOx removal from exhaust). The synthesis of a-TiO2 nanocrystals and their properties have been heavily scrutinized, but there exists a clear gap between the scientific literature, and the scale and price expectation of industrial application. Here it is demonstrated that the industrially most attractive Ti precursor, titanyl sulfate (TiOSO4), can be combined with the green, scalable and fast supercritical flow method to produce phase pure and highly crystalline a-TiO2 nanoparticles with high specific surface area. Control of the nanocrystal morphology is important since it is known that certain facets substantially promote catalytic activity. It is, however, in itself challenging to determine nanocrystal morphology to provide a rational basis for the synthesis control. Here we advocate the use of advanced Rietveld refinement of powder X-ray diffraction data including anisotropic size broadening models in aiding to establish the sample three-dimensional morphology. This relatively quick and robust method assists in overcoming the often encountered ambiguity inherent in two-dimensional to three-dimensional reconstruction of selected particle morphologies with transmission electron microscopy and tomography techniques.

Anisotropic nanomaterials for shape-dependent physicochemical and biomedical applications

This review contributes towards a systematic understanding of the mechanism of shape-dependent effects on nanoparticles (NPs) for elaborating and predicting their properties and applications based on the past two decades of research. Recently, the significance of shape-dependent physical chemistry and biomedicine has drawn ever increasing attention. While there has been a great deal of effort to utilize NPs with different morphologies in these fields, so far research studies are largely localized in particular materials, synthetic methods, or biomedical applications, and have ignored the interactional and interdependent relationships of these areas. This review is a comprehensive description of the NP shapes from theory, synthesis, property to application. We figure out the roles that shape plays in the properties of different kinds of nanomaterials together with physicochemical and biomedical applications. Through systematic elaboration of these shape-dependent impacts, better utilization of nanomaterials with diverse morphologies would be realized and definite strategies would be expected for breakthroughs in these fields. In addition, we have proposed some critical challenges and open problems that need to be addressed in nanotechnology.

Screening Doping Strategies To Mitigate Electron Trapping at Anatase TiO2 Surfaces

Nanocrystalline anatase titanium dioxide is an efficient electron transport material for solar cells and photocatalysts. However, low-coordinated Ti cations at surfaces introduce low-lying Ti 3d states that can trap electrons, reducing charge mobility. Here, a number of dopants (V, Sb, Sn, Zr, and Hf) are examined to replace these low-coordinated Ti cations and reduce electron trapping in anatase crystals. V, Sb, and Sn dopants act as electron traps, while Zr and Hf dopants are found to prevent electron trapping. We also show that alkali metal dopants can be used to fill surface traps by donating electrons into the 3d states of low-coordinated Ti ions. These results provide practical guidance on the optimization of charge mobility in nanocrystalline TiO₂ by doping.

Hollow Nanostructures for Photocatalysis: Advantages and Challenges

Photocatalysis for solar-driven reactions promises a bright future in addressing energy and environmental challenges. The performance of photocatalysis is highly dependent on the design of photocatalysts, which can be rationally tailored to achieve efficient light harvesting, promoted charge separation and transport, and accelerated surface reactions. Due to its unique feature, semiconductors with hollow structure offer many advantages in photocatalyst design including improved light scattering and harvesting, reduced distance for charge migration and directed charge separation, and abundant surface reactive sites of the shells. Herein, the relationship between hollow nanostructures and their photocatalytic performance are discussed. The advantages of hollow nanostructures are summarized as: 1) enhancement in the light harvesting through light scattering and slow photon effects; 2) suppression of charge recombination by reducing charge transfer distance and directing separation of charge carriers; and 3) acceleration of the surface reactions by increasing accessible surface areas for separating the redox reactions spatially. Toward the end of the review, some insights into the key challenges and perspectives of hollow structured photocatalysts are also discussed, with a good hope to shed light on further promoting the rapid progress of this dynamic research field.

Dual Cocatalysts in TiO2 Photocatalysis

Semiconductor photocatalysis is recognized as a promising strategy to simultaneously address energy needs and environmental pollution. Titanium dioxide (TiO₂ ) has been investigated for such applications due to its low cost, nontoxicity, and high chemical stability. However, pristine TiO₂ still suffers from low utilization of visible light and high photogenerated-charge-carrier recombination rate. Recently, TiO₂ photocatalysts modified by dual cocatalysts with different functions have attracted much attention due to the extended light absorption, enhanced reactant adsorption, and promoted charge-carrier-separation efficiency granted by various cocatalysts. Recent progress on the component and structural design of dual cocatalysts in TiO₂ photocatalysts is summarized. Depending on their components, dual cocatalysts decorated on TiO₂ photocatalysts can be divided into the following categories: bimetallic cocatalysts, metal-metal oxide/sulfide cocatalysts, metal-graphene cocatalysts, and metal oxide/sulfide-graphene cocatalysts. Depending on their architecture, they can be categorized into randomly deposited binary cocatalysts, facet-dependent selective-deposition binary cocatalysts, and core-shell structural binary cocatalysts. Concluding perspectives on the challenges and opportunities for the further exploration of dual cocatalyst-modified TiO₂ photocatalysts are presented.

pH effects of the arsenite photocatalytic oxidation reaction on different anatase TiO2 facets

TiO₂ is one of the most cheap materials which can both adsorb arsenic and oxidize arsenite [As(III)] to arsenate [As(V)]. In this study, anatase TiO₂ crystals with different main facets such as {101}, {001} and {100} are synthesized and used to investigate arsenic adsorption kinetics, adsorption isotherms, photocatalytic oxidation (PCO) process and the pH effects. The adsorption kinetics of arsenic on TiO₂ crystals can be described by the pseudo second-order kinetic model. For the adsorption isotherms, the Langmuir model is better than the Freundlich model for arsenic on these TiO₂ crystals. For the PCO process, the rate of As(III) oxidation can be denoted by the pseudo first-order kinetic model. It should be noted that at neutral condition the adsorption and PCO rates of the three kinds of TiO₂ crystals follow the order of {101} > {001} > {100}. The pH effect is above all important for both the arsenic adsorption and its PCO. The highest PCO speed appears at high pH values such as at pH 11 or 12.

Effect of Surface Chemistry and Crystallographic Parameters of TiO2 Anatase Nanocrystals on Photocatalytic Degradation of Bisphenol A

The photocatalytic activity of a series of anatase TiO2 materials with different amounts of exposed (001) facets (i.e., 12% (TiO2-1), 38% (TiO2-3), and 63% (TiO2-3)) was tested in a batch slurry reactor towards liquid-phase bisphenol A (BPA, c0(BPA) = 10 mg/L, ccat. = 125 mg/L) degradation. Photo-electrochemical and photo-luminescence measurements revealed that with the increasing amount of exposed anatase (001) facets, the catalysts generate more electron-hole pairs and OH∙ radicals that participate in the photocatalytic mineralization of pollutants dissolved in water. In the initial stages of BPA degradation, a correlation between % exposure of (001) facets and catalytic activity was developed, which was in good agreement with the findings of the photo-electrochemical and photo-luminescence measurements. TiO2-1 and TiO2-3 solids achieved 100% BPA removal after 80 min in comparison to the TiO2-2 sample. Adsorption of BPA degradation products onto the TiO2-2 catalyst surface was found to have a detrimental effect on the photocatalytic performance in the last stage of the reaction course. Consequently, the global extent of BPA mineralization decreased with the increasing exposure of anatase (001) facets. The major contribution to the enhanced reactivity of TiO2 anatase (001) surface is the Brønsted acidity resulting from dissociative chemisorption of water on a surface as indicated by FTIR, TPD, and MAS NMR analyses.

Hydrothermal/solvothermal synthesis and treatment of TiO2 for photocatalytic degradation of air pollutants: Preparation, characterization, properties, and performance

Photocatalytic oxidation (PCO) is a well-known technology for air purification and has been extensively studied for removal of many air pollutants. Titanium dioxide (TiO₂) is the most investigated photocatalyst in the field of environmental remediation owed to its chemical stability, non-toxicity, and suitable positions of valence and conduction bands. Various preparation techniques including sol-gel, flame hydrolysis, water-in-oil microemulsion, chemical vapour deposition, solvothermal, and hydrothermal have been employed to obtain TiO₂ materials. Hydro-/Solvothermal (HST) synthesis, focus of the present work, can be defined as a preparation method in which crystal growth occurs in a solvent at relatively low temperature (<200 °C) and above atmospheric pressure. This paper aims to provide a comprehensive and critical review of current knowledge regarding the application of HST synthesis for fabrication of TiO₂ nanostructures for indoor air purification. TiO₂ nanostructures are categorized from the morphological standpoint (e.g. nanoparticles, nanotubes, nanosheets, and hierarchically porous) and discussed in detail. The influence of preparation parameters including hydrothermal time, temperature, pH of the reaction medium, solvent, and calcination temperature on physical, chemical, and optical properties of TiO₂ is reviewed. Considering the complex interplay among catalyst properties, a special emphasis is placed on elucidating the interconnection between various photocatalyst features and their impacts on photocatalytic activity.

Amalgamation of N-graphene quantum dots with nanocubic like TiO2: an insight study of sunlight sensitive photocatalysis

In this work, a sunlight-sensitive photocatalyst of nanocubic-like titanium dioxide (TiO₂) and N-doped graphene quantum dots (N-GQDs) is developed through a simple hydrothermal and physical mixing method. The successful amalgamation composite photocatalyst characteristics were comprehensively scrutinized through various physical and chemical analyses. A complete removal of bisphenol A (BPA) is attained by a synthesized composite after 30 min of sunlight irradiation as compared to pure TiO₂. This clearly proved the unique contribution of N-GQDs that enhanced the ability of light harvesting especially under visible light and near-infrared region. This superior characteristic enables it to maximize the absorbance in the entire solar spectrum. However, the increase of N-GQDs weight percentage has created massive oxygen vacancies that suppress the generation of active radicals. This resulted in a longer duration for a complete removal of BPA as compared to lower weight percentage of N-GQDs. Hence, this finding can offer a new insight in developing effective sunlight-sensitive photocatalysts for various complex organic pollutants degradation.

Oxygen-Deficient Dumbbell-Shaped Anatase TiO2-x Mesocrystals with Nearly 100 % Exposed {101} Facets: Synthesis, Growth Mechanism, and Photocatalytic Performance

The development of hierarchical TiO₂ superstructures with new morphologies and intriguing photoelectric properties for utilizing solar energy is known to be an effective approach to alleviate the serious problems of environmental pollution. Herein, unique oxygen-deficient dumbbell-shaped anatase TiO_2-x mesocrystals (DTMCs) enclosed by nearly 100 % {101} facets were readily synthesized by mesoscale transformation in TiCl₃ /acetic acid (HAc) mixed solution, followed by calcination under vacuum. These mesocrystals exhibited much higher photoreactivity toward removing the model pollutants methyl orange and Cr^VI than truncated tetragonal bipyramidal anatase nanocrystals (TNCs), anatase mesocrystals built from truncated tetragonal bipyramidal anatase nanocrystals (TTMCs), and anatase mesocrystals constructed by anatase nanocrystals with nearly 100 % exposed {101} facets (TMCs), revealing that both the oxidation and reduction abilities of anatase TiO₂ were simultaneously enhanced upon fabricating an oxygen-deficient mesocrystalline architecture with about 100 % exposed {101} facets. Further characterization illustrated that such an enhancement of photoreactivity was mainly due to the strengthened light absorption, boosted charge carrier separation, and nearly 100 % exposed {101} facets of the oxygen-deficient dumbbell-shaped anatase mesocrystals. This work will be useful for guiding the synthesis of oxygen-deficient ordered superstructures of metal oxides with desired morphologies and exposed facets for promising applications in environmental remediation.

Experimental Insights into the Growth of Single Truncated Anatase Bipyramids

Fluorine has been recognized to selectively stabilize anatase titanium dioxide (TiO₂ ) crystal facets; however, resolving its physical location at the nanometer scale remains empirically elusive. Here, we provide direct experimental evidence to reveal the spatial distribution of fluorine on single truncated anatase bipyramids (TABs) using nanoscale secondary ion mass spectrometry (NanoSIMS). Fluorine was found to preferentially adsorb on the (001) facet compared to the (101) facet of TABs. Moreover, NanoSIMS depth profiling exhibited a significantly different fluorine distribution between these two facets in the near-surface region, illustrating the essential role of lattice-doped fluorine in the anisotropic crystal growth of TABs.

Polyurethane-Supported Graphene Oxide Foam Functionalized with Carbon Dots and TiO2 Particles for Photocatalytic Degradation of Dyes

The design and optimal synthesis of functional nanomaterials can meet the requirements of energy and environmental science. As a typical photocatalyst, TiO2 can be used to degrade dyes into non-toxic substances. In this work, we demonstrated the in-situ hydrothermal synthesis of carbon quantum dots (CQDs)-modified TiO2 (CQDs/TiO2) particles, and the subsequent fabrication of three-dimensional (3D) graphene oxide (GO) foam doped with CQDs/TiO2 via a facile strategy. By making full use of the up-conversion characteristics of CQDs, the synthesized CQDs/TiO2 exhibited high catalytic activity under visible light. In order to recover the photocatalyst conveniently, CQDs/TiO2 and GO were mixed by ultrasound and loaded on 3D polyurethane foam (PUF) by the multiple impregnation method. It was found that GO, CQDs/TiO2, and PUF reveal synergistic effects on the dye adsorption and photocatalytic degradation processes. The fabricated 3D CQDs/TiO2/GO foam system with a stable structure can maintain a high photocatalytic degradation efficiency after using at least five times. It is expected that the fabricated 3D materials will have potential applications in the fields of oil water separation, the removal of oils, and the photothermal desalination of seawater.

Effect of Single-Atom Cocatalysts on the Activity of Faceted TiO2 Photocatalysts

The synergetic contribution of crystal facets and atomic cocatalysts toward the photoactivity of TiO₂ was fundamentally investigated. Atomic-level dispersed Pt and Au were deposited onto 001-faceted and 101-faceted TiO₂, separately. When used as photocatalysts for photocatalytic H₂ production, Pt/TiO₂-001 showed 1156 and 3 times higher H₂ evolution rate than that of cocatalyst-free TiO₂-001 and Pt-cocatalyzed TiO₂-101. The significantly improved photocatalytic performance was attributed to the efficient separation of high-energy electrons and the sufficient exposure of reactive sites. This study demonstrates a promising way to design single-atom-assisted photocatalysts for high-efficiency water splitting.

Performance Enhancement of CdS/CdSe Quantum Dot-Sensitized Solar Cells with (001)-Oriented Anatase TiO2 Nanosheets Photoanode

CdS/CdSe quantum dot-sensitized solar cells (QDSSCs) were fabricated on two types of TiO₂ photoanodes, namely nanosheets (NSs) and nanoparticles. The TiO₂ NSs with high (001)-exposed facets were prepared via a hydrothermal method, while the TiO₂ nanoparticles used the commercial Degussa P-25. It was found that the pore size, specific surface area, porosity, and electron transport properties of TiO₂ NSs were generally superior to those of P-25. As a result, the TiO₂ NS-based CdS/CdSe QDSSC has exhibited a power conversion efficiency of 4.42%, which corresponds to a 54% improvement in comparison with the P-25-based reference cell. This study provides an effective photoanode design using nanostructure approach to improve the performance of TiO₂-based QDSSCs.

Synthesis of a high-surface area V2O5/TiO2–SiO2 catalyst and its application in the visible light photocatalytic degradation of methylene blue

In the present study, we synthesized several high-surface area V₂O₅/TiO₂–SiO₂ catalysts (vanado titanium silicate, VTS). The synthesized materials are characterized by PXRD, FE-SEM/EDAX, TEM, BET-surface area, FT-IR, UV-Vis, XPS, fluorescence and photocatalytic studies.

Highly effective photocatalytic performance of {001}-TiO2/MoS2/RGO hybrid heterostructures for the reduction of Rh B

Effective separation and rapid transfer of photogenerated electron–hole pairs are key features of photocatalytic materials with high catalytic activity, which could be achieved by co-catalysts.

A recyclable nanosheet of Mo/N-doped TiO2 nanorods decorated on carbon nanofibers for organic pollutants degradation under simulated sunlight irradiation

A novel nanosheet of Mo/N-codoped TiO₂ nanorods immobilized on carbon nanofibers (MNTC nanosheet) was self-synthesized through two facile steps. The Mo/N-doped TiO₂ nanorods dispersed through in situ growth on the network constructed by long and vertical carbon nanofibers (CNFs). The fabricated MNTC nanosheet displayed superb photocatalytic activity of methylene blue (MB), and the degradation ratio by the MNTC nanosheet was nearly twice than that of pure nanoparticles. The photocatalytic activities during the degradation process in the presence of environmental media such as inorganic salts and natural organic matter (NOM) were also determined. Intermediates were analyzed by ion chromatography and electrospray ionization-mass spectrometry to unravel the potential degradation pathways, and the excellent mineralization ratio for MB over MNTC nanosheet was 79.8%. The trapping active species experiments verified that h⁺ was the main active species in the degradation process. Notably, the recycling experiment proved that the MNTC nanosheet was more stable, and it was successfully applied in purifying practical wastewater. Lastly, the fabricated MNTC nanosheet also displayed remarkable degradation performance towards sulfamethoxazole and bisphenol A.

Electrochemical glucose sensing characteristics of two-dimensional faceted and non-faceted CuO nanoribbons

We present faceted and non-faceted crystal cupric oxide (CuO) nanoribbons synthesized by different processes for glucose-sensing applications.

Sorption of uranyl ions on TiO2: Effects of pH, contact time, ionic strength, temperature and HA

Sorption of U(VI) onto TiO₂ as functions of pH, ionic strength, contact time, soil humic acid (SHA), solid-to-liquid ratio and temperature was studied under ambient conditions using batch and spectroscopic approaches. The sorption of U(VI) on TiO₂ was significantly dependent on pH and ionic strength. The presence of SHA slightly enhanced the sorption of U(VI) on TiO₂ below pH4.0, while it inhibited U(VI) sorption in the higher pH range. U(VI) sorption on TiO₂ was favored at high temperatures, and the sorption process was estimated to be endothermic and spontaneous. Reduction of U(VI) to lower valent species was confirmed by X-ray photo-electron spectroscopy analysis. It is very interesting to find that U(VI) sorption on TiO₂ was promoted in solutions with higher back-ground electrolyte concentrations. In the presence of U(VI), higher back-ground electrolyte made more TiO₂ particles aggregate through (001) facets, leading more (101) facets to be exposed. Therefore, the reduction of U(VI) was enhanced by the exposed (101) facets and more U(VI) removal was observed.

Role of the growth step on the structural, optical and surface features of TiO2/SnO2 composites

TiO2/SnO2 composites have attracted considerable attention for their application in photocatalysis, fuel cells and sensors. Structural, morphological, optical and surface features play a pivotal role in photoelectrochemical applications and are critically related to the synthetic route. Most of the reported synthetic procedures require high-temperature treatments in order to tailor the sample crystallinity, usually at the expense of surface hydroxylation and morphology. In this work, we investigate the role of a treatment in an autoclave at a low temperature (100°C) on the sample properties and photocatalytic performance. With respect to samples calcined at 400°C, the milder crystallization treatment promotes anatase phase, mesoporosity and water chemi/physisorption, while reducing the incorporation of heteroatoms within the TiO2 lattice. The role of Sn content was also investigated, showing a marked influence, especially on the structural properties. Notably, at a high content, Sn favours the formation of rutile TiO2 at very low reaction temperatures (100°C), thanks to the structural compatibility with cassiterite SnO2. Selected samples were tested towards the photocatalytic degradation of tetracycline in water under UV light. Overall, the low-temperature treatment enables to tune the TiO2 phase composition while maintaining its surface hydrophilicity and gives rise to well-dispersed SnO2 at the TiO2 surface.

Boosted Water Oxidation Activity and Kinetics on BiVO4 Photoanodes with Multihigh-Index Crystal Facets

The crystal facet of the BiVO₄ photoanode has potential influence on its charge-transfer and separation properties as well as water oxidation kinetics. In the present work, a BiVO₄ polyhedral film with exposed {121}, {132}, {211}, and {251} high-index facets was synthesized by a facile Bi₂O₃ template-induced method and investigated as a photoanode for water oxidation. In comparison with the normal BiVO₄ film with a {121} monohigh-index facet, the BiVO₄ film with multihigh-index crystal facets shows higher activity and faster kinetics for photoelectrochemical water oxidation. Specifically, a higher photocurrent density of 1.21 mA/cm² was achieved on the multihigh-index facet BiVO₄ photoanode at 1.23 V versus reversible hydrogen electrode (RHE) in 0.1 M Na₂SO₄, which is about 200% improved over the normal BiVO₄ photoanode (0.61 mA/cm² at 1.23 V vs RHE). In addition, a negative shift of 300 mV onset potential for water oxidation was observed on the as-prepared BiVO₄ photoanode (0.22 V vs RHE) relative to the normal BiVO₄ photoanode (0.52 V vs RHE) in 0.1 M Na₂SO₄. Although the UV-vis absorbance property and water oxidation pathway not be changed, the charge-transfer and separation properties as well as the overall water oxidation kinetics on the multihigh-index facet BiVO₄ film were boosted obviously. Theory calculations reveal that the adsorption of H₂O molecules on BiVO₄{121} and {132} high-index facets is energetically favorable for subsequent dissociation and oxidation relative to that on {010} and {110} low-index facets. Furthermore, the water oxidation limiting step on {121} and {132} high-index facets of BiVO₄ is changed to the step of two protons reacting with •O to form •OOH species (•O + H₂O_(l) + 2H⁺ + 2e^- → •OOH + 3H⁺ + 3e^-), which is different from the limiting step on {010} and {110} low-index facets that corresponds to the dissociation of H₂O to •OH (2H₂O_(l) + • → •OH + H₂O_(l) + H⁺ + e^-). In addition, the overpotential of water oxidation limiting step on BiVO₄{121} and {132} high-index facets is lower than that on {010} and {110} low-index facets.

Synthesis of mesoporous core-shell TiO2 microstructures with coexposed {001}/{101} facets: enhanced intrinsic photocatalytic performance

TiO₂ microstructures were synthesized via a facile one-step route for enhanced intrinsic photocatalytic performance. The prepared TiO₂ microstructures are featured by both mesoporous core-shell structures and coexposed {001}/{101} facets. Their intrinsic photocatalytic performance were remarkably enhanced due to their high specific surface area, coexposed {001}/{101} facets, and promoted separation of photogenerated carriers. Furthermore, the origin and detailed mechanism for diethylenetriamine (DETA) that served as a high efficient stabilizer of TiO₂ {001} facet have been theoretically investigated. Finally, a new DETA-modified Ostwald ripening mechanism was originally proposed when studying the growth mechanism of the mesoporous core-shell TiO₂ spherical microstructures with coexposed {001}/{101} facets.

Enhanced Photocatalysis from Truncated Octahedral Bipyramids of Anatase TiO2 with Exposed {001}/{101} Facets

In this study, we develop a new synthetic method to grow anatase TiO₂ crystals composed of truncated octahedral bipyramids (TOBs) with exposed {001} and {101} facets by a vapor-solid reaction growth (VSRG) method. The VSRG method employs TiCl_4(g) to react with CaO_(s)/Ca(OH)_2(s) at 823-1043 K under atmospheric pressure. The O-deficient pale-blue TOB TiO₂ crystals display high amount of both {001} and {101} facets. Together, they decompose methylene blue photocatalytically under UV-visible (UV-vis) light irradiation. The most-efficient TOB catalyst VT923 (grown at 923 K, average edge length 400 nm, average thickness 200 nm, and surface area 4.20 m²/g) shows a degradation rate constant k, 0.0527 min^-1. This is close to that of the P25 standard 0.0577 min^-1. However, the surface area of P25 (46.8 m²/g) is about 12 times that of VT923. The extraordinary performance of VT923 is attributed to the presence of high amount of coexisting {001} and {101} facets to form effective surface heterojunctions. They would separate photogenerated electrons and holes effectively on {101} and {001} surfaces, respectively. For VT923, the {001}/{101} ratio is 0.764, which is close to 1, the highest value observed for all TOB samples grown in this study. The surface heterojunctions prolong the electron-hole separation so that VT923 demonstrates the excellent photocatalytic capability. In addition, residual Cl atoms on the exposed faces are easily removed to show clean TiO surface layers with sufficient amount of O-deficient sites in the current samples.

Hydrogen production from glycerol reforming: conventional and green production

The use of biomass to produce transportation and related fuels is of increasing interest. In the traditional approach of converting oils and fats to fuels, transesterification processes yield a very large coproduction of glycerol. Initially, this coproduct was largely ignored and then considered as a useful feedstock for conversion to various chemicals. However, because of the intrinsic large production, any chemical feedstock role would consume only a fraction of the glycerol produced, so other options had to be considered. The reforming of glycerol was examined for syngas production, but more recently the use of photocatalytic decomposition to hydrogen (H2) is of major concern and several approaches have been proposed. The subject of this review is this greener photocatalytic route, especially involving the use of solar energy and visible light. Several different catalyst designs are considered, together with a very wide range of secured rates of H2 production spanning several orders of magnitude, depending on the catalytic system and the process conditions employed. H2 production is especially high when used in glycerol-water mixtures.

Synergistic Cooperation of Rutile TiO2 {002}, {101}, and {110} Facets for Hydrogen Sensing

An oriented TiO₂ thin film-based hydrogen sensor has been demonstrated to have excellent sensing properties at room temperature. The exposed high energy surface offers a low energy barrier for H₂ adsorption and dissociation. In this work, rutile TiO₂ with {101} and {002} facets exposed was controllably synthesized by adjusting the ethanol content of the hydrothermal solvent. The crystalline structure, morphologies, and H₂ sensing performance of the samples varied with the relative ratios of {002} and {101} facets. By increasing the ethanol content, the (002) orientation growth was enhanced and the (101) orientation growth was restrained, the size of the nanorods composing the thin film was reduced and the density of the film was increased. All of the prepared TiO₂ nanorod array film-based hydrogen sensors performed very well at room temperature. The TiO₂ hydrogen sensor with both {110} and {002} facets exposed gave a faster response, as well as better repeatability and stability than those with only {002} facets. Density functional theory simulations have been adopted to reveal the surface interaction of H₂ and the TiO₂ surface. The results suggested that H₂ tended to be adsorbed and dissociated on the (002) and (101) surface. There is a very small active barrier for atomic H to recombine into H₂ molecules on the (110) surface. Thin films with lower density, where more (110) surface is exposed, offered more space for H₂ regeneration, leading to shorter response and recovery times as well as higher sensitivity. The (002), (101), and (110) surfaces of rutile TiO₂ synergistically cooperated to complete the whole H₂ sensing process.

One-step topological preparation of carbon doped and coated TiO2 hollow nanocubes for synergistically enhanced visible photodegradation activity

Various three-dimensional TiO2 hollow structures have attracted strong scientific and technological attention due to their excellent properties. 3D hierarchical TiO2 hollow nanocubes (TiO2-HNBs) are not good candidates for industrial photocatalytic applications due to their large energy gap which is only activated by UV light. Herein, visible-light-responsive carbon doped and coated TiO2-HNBs (C@TiO2-HNBs) with a dominant exposure of {001} facets have been prepared via a template-engaged topotactic transformation process using facile one-step solvothermal treatment and a solution containing ethanol, glucose and TiOF2. The effects of reaction time and glucose/TiOF2 mass ratio on the structure and performance of C@TiO2-HNBs were systematically studied. We found that glucose played an important role in providing H2O during the topological transformation from self-templated TiOF2 cubes into 3D hierarchical TiO2 hollow nanocubes versus dehydration reactions, where its main function was as a carbon source. Coated carbon was deposited predominantly on the surface as sp2 graphitic carbon in extended p conjugated graphite-like environments, and doped carbon mainly replaced Ti atoms in the surface lattice to form a carbonate structure. The results were confirmed using TEM SEM, EDS, XRD, FT-IR, XPS and Raman spectroscopic studies. The C@TiO2-HNBs achieved greatly improved RhB photodegradation activity under visible light irradiation. The catalyst prepared with glucose/TiOF2 at a mass ratio of 0.15 (T24-0.15) showed the highest photodegradation rate of 96% in 40 min, which is 7.0 times higher than those of the TiO2-HNBs and P25. This new synthetic approach proposes a novel way to construct carbon hybridized 3D hierarchical TiO2 hollow nanocubes by combining two modification methods, "element doped" and "surface sensitized", at the same time.

Enhanced TiO2 nanorods photocatalysts with partially reduced graphene oxide for degrading aqueous hazardous pollutants

Enhanced TiO₂ nanorods (TNRs) with partially reduced graphene oxide (RGO) (designated as GT) were prepared for degrading aqueous hazardous pollutants. The degree of RGO oxidation had an important role in affecting the photoelectronic and photocatalytic activities of GT composites. The study examined the impact of the degree of RGO oxidation on the photocatalytic activities. The photocatalytic activity of the materials was investigated for degrading rhodamine b (RhB), methyl orange (MO), methylene blue (MB), and phenol by using ultraviolet (UV) light. The highest photocatalytic activity was observed when the atomic oxygen-to-carbon (O/C) ratio of RGO was 0.130 ± 0.003. This study suggested the photocatalytic performance was maximized by preserving a selected amount of the RGO oxygen-containing groups. The work reported in this study on optimizing the RGO-based TiO₂ photocatalyst could serve as a promising approach for preparing and optimizing other types of carbon-based photocatalysts such as graphene-based CdS.

Rahman MY, Mat Salleh M, Oyama M. Two-Dimensional, Hierarchical Ag-Doped TiO2 Nanocatalysts: Effect of the Metal Oxidation State on the Photocatalytic Properties

This paper reports the synthesis of two-dimensional, hierarchical, porous, and (001)-faceted metal (Ag, Zn, and Al)-doped TiO₂ nanostructures (TNSs) and the study of their photocatalytic activity. Two-dimensional metal-doped TNSs were synthesized using the hydrolysis of ammonium hexafluorotitanate in the presence of hexamethylenetetramine and metal precursors. Typical morphology of metal-doped TNSs is a hierarchical nanosheet that is composed of randomly stacked nanocubes (dimensions of up to 5 μm and 200 nm in edge length and thickness, respectively) and has dominant (001) facets exposed. Raman analysis and X-ray photoelectron spectroscopy results indicated that the Ag doping, compared to Zn and Al, much improves the crystallinity degree and at the same time dramatically lowers the valence state binding energy of the TNS and provides an additional dopant oxidation state into the system for an enhanced electron-transfer process and surface reaction. These are assumed to enhance the photocatalytic of the TNS. In a model of photocatalytic reaction, that is, rhodamine B degradation, the AgTNS demonstrates a high photocatalytic activity by converting approximately 91% of rhodamine B within only 120 min, equivalent to a rate constant of 0.018 m^-1 and ToN and ToF of 94 and 1.57 min^-1, respectively, or 91.1 mmol mg^-1 W^-1 degradation when normalized to used light source intensity, which is approximately 2 times higher than the pristine TNS and several order higher when compared to Zn- and Al-doped TNSs. Improvement of the crystallinity degree, decrease in the defect density and the photogenerated electron and hole recombination, and increase of the oxygen vacancy in the AgTNS are found to be the key factors for the enhancement of the photocatalytic properties. This work provides a straightforward strategy for the preparation of high-energy (001) faceted, two-dimensional, hierarchical, and porous Ag-doped TNSs for potential use in photocatalysis and photoelectrochemical application.

Oxygen vacancy regulation on tungsten oxides with specific exposed facets for enhanced visible-light-driven photocatalytic oxidation

Introduced oxygen vacancy on WO₃ with specific exposed facets was prepared through facile solvothermal treatment and different cooling methods. We demonstrated that the density of oxygen defects could be regulated by different cooling methods and speculated that oxygen vacancy with appropriate concentration range could promote photocatalytic activity through suppressing the recombination of photo-induced carriers. The specific exposed facets with higher oxidation efficiency were prepared by solvothermal reaction. WO₃-A treated by air cooling exhibits the best photocatalytic oxygen evolution rate at 500 μmol g^-1 h^-1 using AgNO₃ as sacrifice agent under visible light (λ > 400 nm) without any co-catalysts, which is about 2 times higher than WO₃-N without oxygen defects. This strategy, using different cooling methods to regulate oxygen vacancy concentration on tungsten oxides, could contribute to the design of other high efficiency photocatalysts.

Influence of fluorine on the synthesis of anatase TiO2 for photocatalytic partial oxidation: are exposed facets the main actors?

The influence of fluorine on TiO₂ exposed facets and on the physico-chemical properties was evaluated and a synergetic effect of the presence of fluorine and the facets' distribution was observed.

Photoelectrocatalytic effect of unbalanced RF magnetron sputtered TiO2 thin film on ITO-coated patterned SiO2 nanocone arrays

Highly increased photocurrent response of unbalanced RF magnetron sputtered TiO₂ thin film on ITO-coated patterned SiO₂ nanocone arrays.