Gold Nanoparticle-Based Colorimetric Strategies for Chemical and Biological Sensing Applications

Simple and rapid detection of ractopamine in pork with comparison of LSPR and LFIA sensors

This study developed a simple and rapid strategic technique to detect ractopamine (chemical growth-promoting agent) in pork. Two highly sensitive and specific gold nanoparticle-based portable sensors, i.e., localized surface plasmon resonance (LSPR) sensors, and lateral flow immunoassay (LFIA) strips were developed to detect veterinary drug residues in food products, that have detrimental effects on humans. Optimization studies were conducted on several sensor devices to improve sensitivity. Each sensor comprised functionalized gold nanoparticles conjugated with ractopamine antibodies. The LSPR sensor chip achieved excellent detection sensitivity = 1.19 fg/mL and was advantageous for quantitative analysis due to its wide dynamic range. On the other hand, LFIA strips provided visual test confirmation and achieved 2.27 ng/mL detection sensitivity, significantly less sensitive than LSPR. The complementary sensors help overcome each other's shortcomings with both the techniques offering ease of use, affordability and rapid diagnosis. Thus, these sensors can be applied on-site for routine screening of harmful drug residues in pork meat. They also provide useful direction for advanced technologies to enhance assay performance for detecting various other food drug contaminants.

A Label-Free Gold Nanoparticles-Based Optical Aptasensor for the Detection of Retinol Binding Protein 4

Retinol-binding protein 4 (RBP4) has been implicated in insulin resistance in rodents and humans with obesity and T2DM, making it a potential biomarker for the early diagnosis of T2DM. However, diagnostic tools for low-level detection of RBP4 are still lagging behind. Therefore, there is an urgent need for the development of T2DM diagnostics that are rapid, cost-effective and that can be used at the point-of-care (POC). Recently, nano-enabled biosensors integrating highly selective optical detection techniques and specificity of aptamers have been widely developed for the rapid detection of various targets. This study reports on the development of a rapid gold nanoparticles (AuNPs)-based aptasensor for the detection of RBP4. The retinol-binding protein aptamer (RBP-A) is adsorbed on the surface of the AuNPs through van der Waals and hydrophobic interactions, stabilizing the AuNPs against sodium chloride (NaCl)-induced aggregation. Upon the addition of RBP4, the RBP-A binds to RBP4 and detaches from the surface of the AuNPs, leaving the AuNPs unprotected. Addition of NaCl causes aggregation of AuNPs, leading to a visible colour change of the AuNPs solution from ruby red to purple/blue. The test result was available within 5 min and the assay had a limit of detection of 90.76 ± 2.81 nM. This study demonstrates the successful development of a simple yet effective, specific, and colorimetric rapid assay for RBP4 detection.

A Real-Time Detection Method of Hg2+ in Drinking Water via Portable Biosensor: Using a Smartphone as a Low-Cost Micro-Spectrometer to Read the Colorimetric Signals

This paper reported a real-time detection strategy for Hg²⁺ inspired by the visible spectrophotometer that used a smartphone as a low-cost micro-spectrometer. In combination with the smartphone's camera and optical accessories, the phone's built-in software can process the received light band image and then read out the spectral data in real time. The sensor was also used to detect gold nanoparticles with an LOD of 0.14 μM, which are widely used in colorimetric biosensors. Ultimately, a gold nanoparticles-glutathione (AuNPs-GSH) conjugate was used as a probe to detect Hg²⁺ in water with an LOD of 1.2 nM and was applied successfully to natural mineral water, pure water, tap water, and river water samples.

Green synthesis of gold nanoparticles using Gracilaria crassa leaf extract and their ecotoxicological potential: Issues to be considered

The use of vegetal species for gold nanoparticles (AuNPs) biosynthesis can constitute an alternative to replacing the extensive use of several hazardous chemicals commonly used during NPs synthesis and, therefore, can reduce biological impacts induced by the release of these products into the natural environment. However, the "green nanoparticles" and/or "eco-friendly nanoparticles" label does not ensure that biosynthesized NPs are harmless to non-target organisms. Thus, we aimed to synthesize AuNPs from seaweed Gracilaria crassa aqueous extract through an eco-friendly, fast, one-pot synthetic route. The formation of spherical, stable, polycrystalline NPs with a diameter of 32.0 nm ± 4.0 nm (mean ±SEM) was demonstrated by UV-vis spectroscopy, field emission scanning electron microscopy, and high-resolution transmission electron microscopy, energy-dispersive X-ray and X-ray diffraction measurement, and Fourier-transform infrared spectroscopy analysis. In addition, different phytocomponents were identified in the biosynthesized AuNPs, using Gas Chromatography-Mass Spectrometry (GC-MS). However, both G. crassa aqueous extract and the biosynthesized AuNPs showed high ecotoxicity in Anopheles stephensi larvae exposed to different concentrations. Therefore, our study supports the potential of seaweed G. crassa as a raw material source for AuNPs biosynthesis while also shedding light on its ecotoxicological potential, which necessitates consideration of its risk to aquatic biota.

An aptasensor for ampicillin detection in milk by fluorescence resonance energy transfer between upconversion nanoparticles and Au nanoparticles

•

Development of A fluorescence aptasensor for the detection of ampicillin in milk.

•

A signal probe construction based on fluorescence resonance energy transfer (FRET).

•

FRET obtained by the interaction of upconversion nanoparticles and Au nanoparticles.

This paper reports a portable fluorescence resonance energy transfer (FRET) aptasensor for ampicillin (Amp) detection using upconversion particles (UCNPs) as energy donors and Au nanoparticles (AuNPs) as energy acceptors. The optimal parameters of the detection system were investigated. Under the optimal conditions, it had a good linear relationship between the fluorescence intensities and Amp concentrations, a high coefficient of determination (R²) of 0.9939, a wide detection range of 10–100 ng/mL, and a low limit of detection (LOD) of 3.9 ng/mL; meanwhile, the aptasensor had high selectivity for Amp against the interference of other antibiotics, and had good recovery and repeatability. Also, its detection performance had been successfully validated by milk samples. Therefore, the developed aptasensor based on FRET between UCNPs and AuNPs has a good prospect for Amp on-site detection in milk with a portable upconversion detection instrument.

SERS monitoring of photoinduced-enhanced oxidative stress amplifier on Au@carbon dots for tumor catalytic therapy

Currently, artificial enzymes-based photodynamic therapy (PDT) is attractive due to its efficient capacity to change the immunosuppressive tumor microenvironment (TME). It is of great significance to study the therapeutic mechanism of novel artificial enzymes in TME through a monitoring strategy and improve the therapeutic effect. In this study, Au@carbon dots (Au@CDs) nanohybrids with a core-shell structure are synthesized, which not only exhibit tunable enzyme-mimicking activity under near-infrared (NIR) light, but also excellent surface-enhanced Raman scattering (SERS) properties. Therefore, Au@CDs show a good capability for monitoring NIR-photoinduced peroxidase-like catalytic processes via a SERS strategy in tumor. Moreover, the Au@CDs deplete glutathione with the cascade catalyzed reactions, thus elevating intratumor oxidative stress amplifying the reactive oxygen species damage based on the NIR-photoinduced enhanced peroxidase and glutathione oxidase-like activities, showing excellent and fast PDT therapeutic effect promoted by photothermal property in 3 min, finally leading to apoptosis in cancer cells. Through SERS monitoring, it is further found that after removing the NIR light source for 33 min, the reactive oxygen species (ROS) activity of the TME is counteracted and eliminated due to the presence of glutathione. This work presents a guidance to rationally design of artificial enzyme for ROS-involved therapeutic strategies and a new spectroscopic tool to evaluate the tumor catalytic therapy.

Core-shell Au-Ag nanoparticles as colorimetric sensing probes for highly selective detection of a dopamine neurotransmitter under different pH conditions

Dopamine (DA) is a vital biomarker for the early diagnosis of dopaminergic dysfunction; therefore, it is important to establish a direct and selective detection tool for DA neurotransmitters. This work reports facilely synthesized Au-Ag core-shell nanoparticles (Au@Ag NPs) as colorimetric sensing probes for highly selective detection of the DA neurotransmitter. Our sensing strategy is based on DA-mediated aggregation of the Au@Ag NPs, which can show a distinct color transition from yellow to greenish grey. With the increase of pH from 6 to 10, the response time of colorimetric transition was significantly reduced by a factor of 10 and the limit of detection (LOD) for DA by a spectroscopic device was estimated to be 0.08 μM. Notably, optimized sensing probes of Au@Ag NPs at pH 10 demonstrated an excellent selectivity to DA against various interfering components (including catecholamines (norepinephrine and epinephrine), lysine, glutamic acid, glucose, or metal ions). Our sensing system also exhibited the reliable detection of DA in spiked human serum with the relative standard deviation lower than 4.0%, suggesting its possible application to the direct detection of DA in biological fluids.

Use of Nanoparticles to Prevent Resistance to Antibiotics-Synthesis and Characterization of Gold Nanosystems Based on Tetracycline

Antimicrobial resistance (AMR) is a serious public health problem worldwide which, according to the World Health Organization (WHO), requires research into new and more effective drugs. In this work, both gold nanoparticles covered with 16-3-16 cationic gemini surfactant (Au@16-3-16) and DNA/tetracycline (DNA/TC) intercalated complexes were prepared to effectively transport tetracycline (TC). Synthesis of the Au@16-3-16 precursor was carried out by using trihydrated gold, adding sodium borohydride as a reducing agent and the gemini surfactant 16-3-16 as stabilizing agent. Circular dichroism and atomic force microscopy techniques were then used to ascertain the optimal R range of the relationship between the concentrations of Au@16-3-16 and the DNA/TC complex (R = CAu@16-3-16/CDNA) that allow the obtainment of stable and compact nanosystems, these characteristics being fundamental for their use as antibiotic transporters. Stability studies over time were carried out for distinct selected Au@16-3-16 and Au@16-3-16/DNA-TC nanoformulations using the ultraviolet−visible spectrophotometry technique, checking their stability for at least one month. In addition, in order to know the charge and size distribution of the nanocomplexes, DLS and zeta potential measurements were performed in the solution. The results showed that the characterized nanosystems were highly charged, stable and of a reduced size (<100 nm) that allows them to cross bacterial membranes effectively (>1 μm). Once the different physicochemical characteristics of the gold nanosystems were measured, Au@16-3-16 and Au@16-3-16/DNA-TC were tested on Escherichia coli and Staphylococcus aureus to study their antibacterial properties and internalization capacity in microbes. Differences in the interaction of the precursors and the compacted nanosystems generated were observed in Gram-positive and Gram-negative bacteria, possibly due to membrane damage or electrostatic interaction with internalization by endocytosis. In the internalization experiments, depending on the treatment application time, the greatest bacterial destruction was observed for all nanoformulations explored at 18 h of incubation. Importantly, the results obtained demonstrate that both new nanosystems based on TC and Au@16-3-16 precursors have optimal antimicrobial properties and would be beneficial for use in patients, avoiding possible side effects.

Site-directed dual bioprobes inducing single-step nano-sandwich assay for the detection of cardiac troponin I

Bioreceptor functionalized metallic nano-colloids have been identified as effective nanobioprobes to realize the detection of an analyte based on a common phenomenon of salt-induced aggregation. In marked contrast to this, we describe a nano-sandwich assay integrating the novel match-pair of aptamer and peptide functionalized gold nanoparticles. The site-directed biomolecular interaction of high affinity aptamer and peptide bioreceptors directed towards distinct sites of cardiac biomarker troponin I; this was found to form a nano-sandwich assay in a peculiar manner. The gold nanoconjugates interact with specific and distant regions of troponin I to result in collision of probes upon target identification. In the presence of TnI, both nanobioprobes bind at their respective sites forming a nano-sandwich pair providing a visual color change from red to blue. Thus, the presence of target TnI itself causes instant agglomeration in just a single-step without addition of any external aggregator. The assay imparts 100% specificity and 90% sensitivity in a dynamic concentration range of 0.1-500 ng/mL troponin I with detection limit as low as 0.084 ng/mL. The applicability of the assay has been validated in clinical samples of acute myocardial infarction patients thus establishing a promising point-of-care detection of TnI.

Fluorescence Quenching of Tyrosine-Ag Nanoclusters by Metal Ions: Analytical and Physicochemical Assessment

A new synthesis method is described for the first time to produce silver nanoclusters (AgNCs) by using the tyrosine (Tyr) amino acid. Several important parameters (e.g., molar ratios, initial pH, reaction time etc.) were optimized to reach the highest yield. The formed Tyr-AgNCs show characteristic blue emission at λem = 410 nm, and two dominant fluorescence lifetime components were deconvoluted (τ1 ~ 3.7 and τ2 ~ 4.9 ns). The NCs contained metallic cores stabilized by dityrosine. For possible application, the interactions with several metal ions from the tap water and wastewater were investigated. Among the studied cations, four different ions (Cu2+, Ni2+, Fe3+, and Rh3+) had a dominant effect on the fluorescence of NCs. Based on the detected quenching processes, the limit of detection of the metal ions was determined. Static quenching (formation of a non-luminescent complex) was observed in all cases by temperature-dependent measurements. The calculated thermodynamic parameters showed that the interactions are spontaneous ranked in the following order of strength: Cu2+ > Fe3+ > Rh3+ > Ni2+. Based on the sign and relations of the standard enthalpy (ΔH°) and entropy changes (ΔS°), the dominant forces were also identified.

Colorimetric Approach for Nucleic Acid Salmonella spp. Detection: A Systematic Review

Water- and food-related health issues have received a lot of attention recently because food-poisoning bacteria, in particular, are becoming serious threats to human health. Currently, techniques used to detect these bacteria are time-consuming and laborious. To overcome these challenges, the colorimetric strategy is attractive because it provides simple, rapid and accurate sensing for the detection of Salmonella spp. bacteria. The aim of this study is to review the progress regarding the colorimetric method of nucleic acid for Salmonella detection. A literature search was conducted using three databases (PubMed, Scopus and ScienceDirect). Of the 88 studies identified in our search, 15 were included for further analysis. Salmonella bacteria from different species, such as S. Typhimurium, S. Enteritidis, S. Typhi and S. Paratyphi A, were identified using the colorimetric method. The limit of detection (LoD) was evaluated in two types of concentrations, which were colony-forming unit (CFU) and CFU per mL. The majority of the studies used spiked samples (53%) rather than real samples (33%) to determine the LoDs. More research is needed to assess the sensitivity and specificity of colorimetric nucleic acid in bacterial detection, as well as its potential use in routine diagnosis.

Colorimetric visualization of histamine secreted by basophils based on DSP-functionalized gold nanoparticles

Histamine released by activated basophils has become an important biomarker and therapeutic target in the development of allergic diseases. To date, several gold nanoparticle (AuNP)-based nanosensors have been reported for histamine detection in foods. However, rapid, highly sensitive and direct detection of histamine in allergic diseases is still lacking due to the complexity of the physical environment. Herein, we developed a novel nanosensor for colorimetric visualization of histamine in activated basophils by simply coupling dithiobis(succinimidylpropionate) (DSP) on the surface of AuNPs (DSP-AuNPs). The DSP moiety serves as a linker and can react with the aliphatic amino group of histamine, and the imidazole ring of histamine can selectively bind with Au by means of p-p conjugation, thus inducing the aggregation of AuNPs. In this study, we experimentally proved that DSP-AuNPs showed good sensitivity and selectivity to histamine among various amino acids, including histidine. Additionally, this nanosensor displayed a rapid response to histamine with a linear range of 0.8-2.5 μM, and the limit of detection (LOD) was 0.014 μM, which is a relatively low LOD in comparison with those of other AuNP-based nanosensors. Finally, DSP-AuNPs are used, for the first time, to successfully detect endogenous histamine changes in activated basophils. Therefore, our work may provide a promising strategy to monitor histamine levels in the basophil activation test.

The Integration of Gold Nanoparticles with Polymerase Chain Reaction for Constructing Colorimetric Sensing Platforms for Detection of Health-Related DNA and Proteins

Polymerase chain reaction (PCR) is the standard tool in genetic information analysis, and the desirable detection merits of PCR have been extended to disease-related protein analysis. Recently, the combination of PCR and gold nanoparticles (AuNPs) to construct colorimetric sensing platforms has received considerable attention due to its high sensitivity, visual detection, capability for on-site detection, and low cost. However, it lacks a related review to summarize and discuss the advances in this area. This perspective gives an overview of established methods based on the combination of PCR and AuNPs for the visual detection of health-related DNA and proteins. Moreover, this work also addresses the future trends and perspectives for PCR-AuNP hybrid biosensors.

Detection of SARS-CoV-2 virus via dynamic light scattering using antibody-gold nanoparticle bioconjugates against viral spike protein

Mass testing for the diagnosis of COVID-19 has been hampered in many countries owing to the high cost of genetic material detection. This study reports on a low-cost immunoassay for detecting SARS-CoV-2 within 30 min using dynamic light scattering (DLS). The immunosensor comprises 50-nm gold nanoparticles (AuNPs) functionalized with antibodies against SARS-CoV-2 spike glycoprotein, whose bioconjugation was confirmed using transmission electron microscopy (TEM), UV-Vis spectroscopy, Fourier transform infrared spectroscopy (FTIR), and surface-enhanced Raman scattering spectroscopy (SERS). The specific binding of the bioconjugates to the spike protein led to an increase in bioconjugate size, with a limit of detection (LOD) 5.29 × 10³ TCID₅₀/mL (Tissue Culture Infectious Dose). The immunosensor was also proven to be selective upon interaction with influenza viruses once no increase in size was observed after DLS measurement. The strategy proposed here aimed to use antibodies conjugated to AuNPs as a generic platform that can be extended to other detection principles, enabling technologies for low-cost mass testing for COVID-19.

The development of a colorimetric biosensing assay for the detection of Helicobacter pylori in feces

As Helicobacter pylori (H. pylori) is closely related to the occurrence of gastric diseases such as chronic gastritis, peptic ulcer, and gastric cancer, early detection of H. pylori is an urgent need. In this study, oligonucleotide probes conjugated with gold nanoparticles (AuNPs) were used in combination with H. pylori-specific aptamers for the rapid detection of H. pylori in stool samples, which converted the method of detection from proteins to nucleic acids. Therefore, qualitative detection of H. pylori can be achieved by observing color changes through the aggregation (red to purple) or deaggregation (purple to red) of AuNPs, and further quantitative detection can be achieved through UV spectrometry. The detection limit of the colorimetric biosensing method is 25 CFU/mL (S/N = 3), which is favorably comparable to other reported detection methods. Compared with the existing detection methods for H. pylori, this colorimetric biosensing method has no limitations to the test subjects. All these features render the colorimetric biosensing assay a promising method for the clinical field detection of H. pylori.

Effect of rhodamine 6G dye molecular interactions on counterintuitive self-assembly of noble metal nanorods

HYPOTHESIS

Self-assembled nanostructures with highly ordered and diversified patterns can be obtained by adding additives that directionally control the interparticle interactions. However, due to the complex non-covalent weak interactions in the self-assembly process, the active mechanism of additives is not fully understood, resulting in the limitation of obtaining the nano-superstructures. The introduction of rhodamine 6G (R6G) enables gold nanorods (GNRs) self-assembled into a counterintuitive tetragonal superlattice, during which the exploration of the influence of R6G molecular interactions on the GNRs self-assembly is of importance.

EXPERIMENTS

We present the detailed investigations of spacial configuration, binding modes, and aggregated degree of R6G molecule on formation of the tetragonal GNRs superlattices by combining the experimental and simulated results.

FINDINGS

By analyzing the peak position and peak intensity in the fluorescent spectra of assembled samples and pure R6G samples, H-dimer is verified as the main cause for inducing the tetragonal superstructures. Molecular dynamics simulations reveal that 2-3 H-dimers adsorbed obliquely in a zigzag chain manner on the surface of GNRs is the most stable state of the self-assembly. This work would contribute to a deeper understanding of the complex colloidal nanoparticle self-assemblies and push forward the development of the bottom-up nanoscale superstructures.

CASCADE: Naked eye-detection of SARS-CoV-2 using Cas13a and gold nanoparticles

The COVID-19 pandemic has brought to light the need for fast and sensitive detection methods to prevent the spread of pathogens. The scientific community is making a great effort to design new molecular detection methods suitable for fast point-of-care applications. In this regard, a variety of approaches have been developed or optimized, including isothermal amplification of viral nucleic acids, CRISPR-mediated target recognition, and read-out systems based on nanomaterials.

Herein, we present CASCADE (CRISPR/CAS-based Colorimetric nucleic Acid DEtection), a sensing system for fast and specific naked-eye detection of SARS-CoV-2 RNA. In this approach, viral RNA is recognized by the LwaCas13a CRISPR protein, which activates its collateral RNase activity. Upon target recognition, Cas13a cleaves ssRNA oligonucleotides conjugated to gold nanoparticles (AuNPs), thus inducing their colloidal aggregation, which can be easily visualized. After an exhaustive optimization of functionalized AuNPs, CASCADE can detect picomolar concentrations of SARS-CoV-2 RNA. This sensitivity is further increased to low femtomolar (3 fM) and even attomolar (40 aM) ranges when CASCADE is coupled to RPA or NASBA isothermal nucleic acid amplification, respectively. We finally demonstrate that CASCADE succeeds in detecting SARS-CoV-2 in clinical samples from nasopharyngeal swabs.

In conclusion, CASCADE is a fast and versatile RNA biosensor that can be coupled to different isothermal nucleic acid amplification methods for naked-eye diagnosis of infectious diseases.

A simple and sensitive AuNPs-based colorimetric aptasensor for specific detection of azlocillin

A new colorimetric biosensor for specific detection of azlocillin was developed by using DNA aptamer as recognition element and unmodified gold nanoparticles (AuNPs) as colorimetric indicator. In the absence of azlocillin, the AuNPs were protected by the aptamer and stabilized at high NaCl concentrations, displaying a red solution. In the presence of azlocillin, the aptamer reacts specifically with azlocillin, resulting in the aggregation of AuNPs and an apparent red to blue color change. The characteristic change can be easily observed by the naked eye and quantitatively detected by an ultraviolet-visible (UV-Vis) spectrometer. Under the optimal conditions, the absorbance variation at 522 nm (ΔA₅₂₂) of AuNPs changed proportionally with increasing concentration of azlocillin, which exhibited a linear relationship in the concentration range of 50 nM to 500 nM, with a detection limit of 11.6 nM. Furthermore, the aptasensor was successfully used to detect azlocillin in milk and tap water samples, with recoveries ranging from 97.64% to 102.21% and a relative standard deviation (RSD) less than 3.81%.

Gold nanoparticle-based optical nanosensors for food and health safety monitoring: recent advances and future perspectives

Modern society has been facing serious health-related problems including food safety, diseases and illness. Hence, it is urgent to develop analysis methods for the detection and control of food contaminants, disease biomarkers and pathogens. As the traditional instrumental methods have several disadvantages, including being time consuming, and having high cost and laborious procedures, optical nanosensors have emerged as promising alternative or complementary approaches to those traditional ones. With the advantages of simple preparation, high surface-to-volume ratio, excellent biocompatibility, and especially, unique optical properties, gold nanoparticles (AuNPs) have been demonstrated as excellent transducers for optical sensing systems. Herein, we provide an overview of the synthesis of AuNPs and their excellent optical properties that are ideal for the development of optical nanosensors based on local surface plasmon resonance (LSPR), colorimetry, fluorescence resonance energy transfer (FRET), and surface-enhanced Raman scattering (SERS) phenomena. We also review the sensing strategies and their mechanisms, as well as summarizing the recent advances in the monitoring of food contaminants, disease biomarkers and pathogens using developed AuNP-based optical nanosensors in the past seven years (2015-now). Furthermore, trends and challenges in the application of these nanosensors in the determination of those analytes are discussed to suggest possible directions for future developments.

Plasmonic Nanomaterials for Colorimetric Biosensing: A Review

In the last few decades, plasmonic colorimetric biosensors raised increasing interest in bioanalytics thanks to their cost-effectiveness, responsiveness, and simplicity as compared to conventional laboratory techniques. Potential high-throughput screening and easy-to-use assay procedures make them also suitable for realizing point of care devices. Nevertheless, several challenges such as fabrication complexity, laborious biofunctionalization, and poor sensitivity compromise their technological transfer from research laboratories to industry and, hence, still hamper their adoption on large-scale. However, newly-developing plasmonic colorimetric biosensors boast impressive sensing performance in terms of sensitivity, dynamic range, limit of detection, reliability, and specificity thereby continuously encouraging further researches. In this review, recently reported plasmonic colorimetric biosensors are discussed with a focus on the following categories: (i) on-platform-based (localized surface plasmon resonance, coupled plasmon resonance and surface lattice resonance); (ii) colloid aggregation-based (label-based and label free); (iii) colloid non-aggregation-based (nanozyme, etching-based and growth-based).

Advancement in Nanoparticle-Based Biosensors for Point-of-Care In Vitro Diagnostics

Abstract:

Recently, there has been great progress in the field of extremely sensitive and precise detection of bioanalytes. The importance of the utilization of nanoparticles in biosensors has been recognized due to their unique properties. Specifically, nanoparticles of gold, silver, and magnetic plus graphene, quantum dots, and nanotubes of carbon are being keenly considered for utilizations within biosensors to detect nucleic acids, glucose, or pathogens (bacteria as well as a virus). Taking advantage of nanoparticles, faster and sensitive biosensors can be developed. Here we review the nanoparticles' contribution to the biosensors field and their potential applications.

Ultrasensitive nano-gold labelled, duplex lateral flow immunochromatographic assay for early detection of sugarcane mosaic viruses

Sugarcane is one of the important food and bioenergy crops, cultivated all over the world except European continent. Like many other crops, sugarcane production and quality are hampered by various plant pathogens, among them viruses that infect systemically and cause severe impact to cane growth. The viruses are efficiently managed by their elimination through tissue culture combined with molecular diagnostics, which could detect virus titre often low at 10^-12 g mL^-1. To harmonize the virus diagnostics by molecular methods, we established a nanocatalysis-based high sensitive lateral flow immunochromatographic assay (LFIA) simultaneously to detect two major sugarcane viruses associated with mosaic disease in sugarcane. LFIA is known for poor sensitivity and stability with its signalling conjugates. However, we synthesized positively charged Cysteamine-gold nanoparticles and used them to prepare highly stable to sensitive immunoconjugates and as a colourimetric detection label. Further nanogold signal enhancement was performed on LFIA to obtain a high detection sensitivity, which is higher than the conventional immunoassays. The linear detection range of the nano-LIFA was 10^-6 to 10^-9 g mL^-1, and with the signal enhancement, the LOD reached up to 10^-12 g ml^-1. This research paper provides relative merits and advancement on nano-LFIA for specific detection of sugarcane viruses in sugarcane for the first time.

Giant Magnetoresistance Biosensors in Biomedical Applications

The giant magnetoresistance (GMR) effect has seen flourishing development from theory to application in the last three decades since its discovery in 1988. Nowadays, commercial devices based on the GMR effect, such as hard-disk drives, biosensors, magnetic field sensors, microelectromechanical systems (MEMS), etc., are available in the market, by virtue of the advances in state-of-the-art thin-film deposition and micro- and nanofabrication techniques. Different types of GMR biosensor arrays with superior sensitivity and robustness are available at a lower cost for a wide variety of biomedical applications. In this paper, we review the recent advances in GMR-based biomedical applications including disease diagnosis, genotyping, food and drug regulation, brain and cardiac mapping, etc. The GMR magnetic multilayer structure, spin valve, and magnetic granular structure, as well as fundamental theories of the GMR effect, are introduced at first. The emerging topic of flexible GMR for wearable biosensing is also included. Different GMR pattern designs, sensor surface functionalization, bioassay strategies, and on-chip accessories for improved GMR performances are reviewed. It is foreseen that combined with the state-of-the-art complementary metal-oxide-semiconductor (CMOS) electronics, GMR biosensors hold great promise in biomedicine, particularly for point-of-care (POC) disease diagnosis and wearable devices for real-time health monitoring.

Electrochemical (Bio)Sensors for the Detection of Organophosphorus Pesticides Based on Nanomaterial-Modified Electrodes: A Review

Organophosphorus pesticides were easily remained in fruits and vegetables which would be harm to the environmental safety and human health. In recent years, due to the simple preparation process, fast response and high sensitivity, the electrochemical (bio)sensors have received increasing attention, which were extensively used as the sensing platform for the detection of OPPs. The mechanisms for the determination of OPPs mainly included redox of nitrophenyl OPPs, enzyme hydrolysis and inhibition, immunosensor, aptasensor. Nowadays, the mainly explored electrode material has focused on metal-organic frameworks, metal and metal derivatives, carbon materials (carbon nanotube, graphene, g-C3N4), MXene, etc. These nanomaterials played important roles in the electrochemical (bio)sensors, which included: (a) as an electrocatalyst to promote the redox reaction, (b) as a carrier to load the enzyme or aptamer, (c) as a recognizer to identify the targets. The nanomaterials-based electrochemical (bio)sensor was a rapid, cost-effective methods to detect OPPs with high sensitivity. Besides, this review compared the analytical performance of different nanomaterials-based electrochemical (bio)sensors, and also identified the key challenges in the future. It would provide new ideas and insights to the further development and application of electrochemical (bio)sensors and the detection of pesticides in real samples.

A Charge-Switchable Zwitterionic Peptide for Rapid Detection of SARS-CoV-2 Main Protease

The transmission of SARS-CoV-2 coronavirus has led to the COVID-19 pandemic. Nucleic acid testing while specific has limitations for mass surveillance. One alternative is the main protease (Mpro ) due to its functional importance in mediating the viral life cycle. Here, we describe a combination of modular substrate and gold colloids to detect Mpro via visual readout. The strategy involves zwitterionic peptide that carries opposite charges at the C-/N-terminus to exploit the specific recognition by Mpro . Autolytic cleavage releases a positively charged moiety that assembles the nanoparticles with rapid color changes (t<10 min). We determine a limit of detection for Mpro in breath condensate matrices <10 nM. We further assayed ten COVID-negative subjects and found no false-positive result. In the light of simplicity, our test for viral protease is not limited to an equipped laboratory, but also is amenable to integrating as portable point-of-care devices including those on face-coverings.

Phytosynthesis of silver nanoparticles from Jatropha integerrima Jacq. flower extract and their possible applications as antibacterial and antioxidant agent

Jatropha integerrima Jacq. flower extract was used for the synthesis of silver nanoparticles in the current study. Various spectroscopic analyses were used to characterize the synthesized nanoparticles (JIF-AgNPs). The antibacterial efficacy of JIF-AgNPs was studied by well diffusion and microdilution techniques. In addition, the impact of JIF-AgNPs on free radicals was evaluated. On the ultraviolet–visible spectrum, the nanoparticles exhibit the highest absorbance at 422 nm. Based on the Fourier transform infrared spectrum, phenols and amino acids were involved in capping the JIF-AgNPs. Crystalline sphere-shaped nanoparticles with an average size of 50.07 nm and zeta potential of −19.0 mV were confirmed by X-ray diffraction, transmission electron microscopy, and dynamic light scattering analysis respectively. The JIF-AgNPs exhibit the highest and lowest growth inhibitory activity towards E. coli and B. subtilis. The minimal inhibitory concentration of JIF-AgNPs against E. coli, K. pneumoniae, S. aureus, and B. subtilis were 2.5, 5.0, 5.0, and 7.5 μg/mL, respectively. The JIF-AgNPs exhibited significant radical scavenging activities against DPPH (IC₅₀-32.5 ± 0.06 µg/mL), hydroxyl (IC₅₀-25 ± 0.09 µg/mL), Superoxide (IC₅₀-42.5 ± 0.13 µg/mL), and ABTs (IC₅₀-33.5 ± 0.15 µg/mL). Thus, synthesized nanoparticles were a good alternative to develop an antibacterial and antioxidant agent.

Colorimetric and Electrochemical Methods for the Detection of SARS-CoV-2 Main Protease by Peptide-Triggered Assembly of Gold Nanoparticles

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) main protease (Mpro) has been regarded as one of the ideal targets for the development of antiviral drugs. The currently used methods for the probing of Mpro activity and the screening of its inhibitors require the use of a double-labeled peptide substrate. In this work, we suggested that the label-free peptide substrate could induce the aggregation of AuNPs through the electrostatic interactions, and the cleavage of the peptide by the Mpro inhibited the aggregation of AuNPs. This fact allowed for the visual analysis of Mpro activity by observing the color change of the AuNPs suspension. Furthermore, the co-assembly of AuNPs and peptide was achieved on the peptide-covered electrode surface. Cleavage of the peptide substrate by the Mpro limited the formation of AuNPs/peptide assembles, thus allowing for the development of a simple and sensitive electrochemical method for Mpro detection in serum samples. The change of the electrochemical signal was easily monitored by electrochemical impedance spectroscopy (EIS). The detection limits of the colorimetric and electrochemical methods are 10 and 0.1 pM, respectively. This work should be valuable for the development of effective antiviral drugs and the design of novel optical and electrical biosensors.

Detection and Difference Analysis of the Enzyme Activity of Colloidal Gold Nanoparticles With Negatively Charged Surfaces Prepared by Different Reducing Agents

Nanozymes are particles with diameters in the range of 1–100 nm, which has been widely studied due to their biological enzyme-like properties and stability that natural enzymes do not have. In this study, several reducing agents with different structures (catechol (Cc), hydroquinone (Hq), resorcinol (Rs), vitamin C (Vc), pyrogallic acid (Ga), sodium citrate (Sc), sodium malate (Sm), and sodium tartrate (St)) were used to prepare colloidal gold with a negative charge and similar particle size by controlling the temperature and pH. The affinity analysis of the substrate H2O2 and TMB showed that the order of activities of colloidal gold Nanozymes prepared by different reducing agents was Cc, Hq, Rs, Vc, Ga, Sc, Sm, St. It was also found that the enzyme activity of colloidal gold reduced by benzene rings is higher than that of the colloidal gold enzyme reduced by linear chains. Finally, we discussed the activity of the colloidal gold peroxidase based on the number and position of isomers and functional groups; and demonstrated that the nanozymes activity is affected by the surface activity of colloidal gold, the elimination of hydroxyl radicals and the TMB binding efficiency.

A review on colorimetric assays for DNA virus detection

Early detection is one of the ways to deal with DNA virus widespread prevalence, and it is necessary to know new diagnostic methods and techniques. Colorimetric assays are one of the most advantageous methods in detecting viruses. These methods are based on color change, which can be seen either with the naked eye or with special devices. The aim of this study is to introduce and evaluate effective colorimetric methods based on amplification, nanoparticle, CRISPR/Cas, and Lateral flow in the diagnosis of DNA viruses and to discuss the effectiveness of each of the updated methods. Compared to the other methods, colorimetric assays are preferred for faster detection, high efficiency, cheaper cost, and high sensitivity and specificity. It is expected that the spread of these viruses can be prevented by identifying and developing new methods.

Veni, Vidi, Vici: Immobilized Peptide-Based Conjugates as Tools for Capture, Analysis, and Transformation

Analysis of peptide biomarkers of pathological states of the organism is often a serious challenge, due to a very complex composition of the cell and insufficient sensitivity of the current analytical methods (including mass spectrometry). One of the possible ways to overcome this problem is sample enrichment by capturing the selected components using a specific solid support. Another option is increasing the detectability of the desired compound by its selective tagging. Appropriately modified and immobilized peptides can be used for these purposes. In addition, they find application in studying the specificity and activity of proteolytic enzymes. Immobilized heterocyclic peptide conjugates may serve as metal ligands, to form complexes used as catalysts or analytical markers. In this review, we describe various applications of immobilized peptides, including selective capturing of cysteine-containing peptides, tagging of the carbonyl compounds to increase the sensitivity of their detection, enrichment of biological samples in deoxyfructosylated peptides, and fishing out of tyrosine–containing peptides by the formation of azo bond. Moreover, the use of the one-bead-one-compound peptide library for the analysis of substrate specificity and activity of caspases is described. Furthermore, the evolution of immobilization from the solid support used in peptide synthesis to nanocarriers is presented. Taken together, the examples presented here demonstrate immobilized peptides as a multifunctional tool, which can be successfully used to solve multiple analytical problems.

A smartphone-based visual biosensor for CRISPR-Cas powered SARS-CoV-2 diagnostics

The pandemic of coronavirus disease 2019 (COVID-19) resulted from novel severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) has become a worldwide concern. It is imperative to develop rapid, sensitive, and specific biosensing methods. Herein, we developed a CRISPR-Cas12a powered visual biosensor with a smartphone readout for ultrasensitive and selective detection of SARS-CoV-2. Simply, the SARS-CoV-2 derived nucleic acids triggered CRISPR-Cas12a based indiscriminate degradation of a single-stranded DNA that was supposed to link two gold nanoparticles, inducing the dis-aggregation of gold nanoparticles and thus generating observable color changes. This change can be readily distinguished by naked eyes as well as a smartphone with a Color Picker App. The proposed biosensor was successfully applied to detect SARS-CoV-2 gene in synthetic vectors, transcribed RNA and SARS-CoV-2 pseudoviruses. It rendered “single copy resolution” as evidenced by the 1 copy/μL limit of detection of pseudoviruses with no cross-reactivity. When the developed biosensor was challenged with SARS-CoV-2 clinical bio-samples, it provided 100% agreement (both positive and negative) with qPCR results. The sample-to-result time was roughly 90 min. Our work provides a novel and robust technology for ultrasensitive detection of SARS-CoV-2 that could be used clinically.

Colorimetric determination of Listeria monocytogenes using aptamer and urease dual-labeled magnetic nanoparticles and cucurbit[7]uril-mediated supramolecular assembly of gold nanoparticle

A host-guest colorimetric strategy is described for the detection of Listeria monocytogenes (L. monocytogenes). The optical probes were self-assembled based on the supramolecular interactions between the carbonyl groups of cucurbit[7]uril portals and gold nanoparticles (CB[7]-AuNPs). Aptamer and urease modified magnetic nanoparticles were used to specifically recognize and binding to L. monocytogenes, simultaneously hydrolyzing urea to produce ammonium ion (NH₄⁺) that can reverse CB[7] induced AuNPs aggregation. In the presence of L. monocytogenes, the above-mentioned magnetic conjugates preferentially bind to the bacterial surface, which results in blocking the catalytic active sites, thus inhibiting the production of ammonium ions. The normalized absorbance ratio of A_{700 nm}/A_{525 nm} was proportional to the L. monocytogenes concentration ranging from 10 to 10⁶ cfu·mL^-1, and the visual determination can be done down to 10 cfu·mL^-1. For spiked food samples analyzed without pre-enrichment, recoveries of 98.4% to 99.3% were achieved could be verified and RSD were less than 10%. This work may offer a broad prospect for sensitive and specific determination  of pathogens.

Colorimetric Measurement of Deltamethrin Pesticide Using a Paper Sensor Based on Aggregation of Gold Nanoparticles

Deltamethrin (DEL) is one of the most commonly used pyrethroid pesticides that can cause serious harms to the ecological environment and human health. Herein, we have developed a paper-based colorimetric sensor impregnated with gold nanoparticles (AuNPs) for on-site determination of DEL pesticide. AuNPs show obvious color change on paper device with the presence of DEL. Measuring the gray intensity of the AuNPs on the reaction zone of the paper sensor allows accurate quantitative analysis. The detection mechanism of DEL on paper sensor was confirmed by UV-Vis spectrophotometry (UV-Vis), Fourier transform infrared spectroscopy (FT-IR), and transmission electron microscope (TEM). Under optimal conditions, the colorimetric sensor exhibited high sensitivity, rapid detection, and low detection limit within the values stipulated by Chinese detection standards (LOD = 0.584 mg/L). Besides, detecting DEL in vegetable and fruit samples also gave satisfying results, which were much consistent with those obtained by spectrophotometry. Overall, this work provided a user-friendly, cost-effective and visualized detection platform, which could be applied to rapidly detect DEL pesticides in the food safety field.

Colorimetric Detection of Organophosphate Pesticides Based on Acetylcholinesterase and Cysteamine Capped Gold Nanoparticles as Nanozyme

Organophosphates (OPs) are neurotoxic agents also used as pesticides that can permanently block the active site of the acetylcholinesterase (AChE). A robust and sensitive detection system of OPs utilising the enzyme mimic potential of the cysteamine capped gold nanoparticles (C-AuNPs) was developed. The detection assay was performed by stepwise addition of AChE, parathion ethyl (PE)-a candidate OP, acetylcholine chloride (ACh), C-AuNPs, and 3, 3′, 5, 5′-tetramethylbenzidine (TMB) in the buffer solution. The whole sensing protocol completes in 30–40 min, including both incubations. The Transmission Electron Microscopy (TEM) results indicated that the NPs are spherical and have an average size of 13.24 nm. The monomers of C-AuNPs exhibited intense catalytic activity (nanozyme) for the oxidization of TMB, revealed by the production of instant blue colour and confirmed by a sharp peak at 652 nm. The proposed biosensor’s detection limit and linear ranges were 5.8 ng·mL⁻¹ and 11.6–92.8 ng·mL⁻¹, respectively, for PE. The results strongly advocate that the suggested facile colorimetric biosensor may provide an excellent platform for on-site monitoring of OPs.

1,5-anhydroglucitol biosensor based on light-addressable potentiometric sensor with RGO-CS-Fc/Au NPs nanohybrids

In this paper, a novel silicon-based light-addressable potentiometric sensor (LAPS) has been designed for the detection of 1,5-anhydroglucitol (1,5-AG) in human serum. Reduced graphene oxide-chitosan-ferrocene (RGO-CS-Fc)/AuNPs nanohybrids and pyranose oxidase (PROD) enzyme is used to fabricate biological sensitive membrane unit by layer-by-layer assembly technology. When a bias voltage is provided to the LAPS system, the catalytic oxidation reaction between 1,5-AG and PROD to produce H₂O₂. The by-product H₂O₂ can oxidize Fc(Fe²⁺) ions in RGO-CS-Fc nanohybrids into Fc(Fe³⁺) ions, which cause the potential of the sensitive membrane surface to change and the potential shift of I-V curve will generate a corresponding offset response. Under the optimal conditions, the potential shift of the LAPS is linearly related to the concentration of 1,5-AG at 10 µg·mL^-1 -350 µg·mL^-1 with the correlation coefficient of 0.97414. The sensitivity is 0.44273 mV/µg·mL^-1 and the lowest detection limit is 10 µg·mL^-1. In addition, the biosensor showed good specificity, acceptable stability and satisfactory recovery rates (91.28%-107.66%), which would be a potential testing methods in actual clinical samples.

Analyte-restrained silver coating of gold nanostructures: an efficient strategy to advance multicolorimetric probes

Visual detection based on gold nanorods (AuNRs) has gained tremendous attention in sensing applications owing to the potential for simple, inexpensive, instrument-free, and on-site detection. The proper selection of the mechanism involved in the interaction between the analyte and the nanostructure plays a significant role in designing a selective and multicolorimetric probe for visual purposes. A winning mechanism to develop multicolorimetric probes is the silver metalization of AuNRs. Herein, an unprecedented idea is presented to expand the variety of multicolorimetric sensors relying on the mechanism of silver deposition. We introduce the anti-silver deposition mechanism in which the analyte directly or indirectly restrains the silver coating of AuNRs. To ascertain the anti-silver deposition mechanism, we have exploited the proposed idea for the direct detection of nitrate. The presence of nitrate (as restrainer agent), which was firstly treated with ascorbic acid (as reducing agent), induced a decrease in the spectral blueshift of AuNRs along with diverse sharp color transitions from reddish-orange (blank) to maroon, wine, berry/purple, dark blue, teal, green, seafoam, and mint. The difference in the spectrum area of the probe in the absent (S_o) and presence (S) of nitrate were linearly proportional to nitrate concentration in the range of 0.5-5.5 mmol l^-1and the limit of detection was calculated to be 465μmol l^-1. Furthermore, the practicability of the multicolor probe was assessed by the determination of nitrate in complex environmental samples.

3-Aminophenylboronic acid-mediated aggregation of gold nanoparticles for colorimetric sensing of iohexol in environmental and biological samples

Iohexol (IHO), as one of iodinated X-ray contrast, is often used as not only a chemical marker for tracking wastewater contamination in aquatic environment, but also an ideal glomerular filtration rate marker for explorating kidney disease. To these aims, it is important to establish reliable, fast, and cheap methods to detect IHO in environmental and biological samples. This work describes for the first time the development of a selective, sensitive and reliable colorimetric sensing assay for the fast determination of IHO in environmental and biological samples based on 3-aminophenylboronic acid (3-APBA) mediated aggregation of gold nanoparticles (AuNPs). In this approach, 3-APBA can assemble on the AuNPs surface through electrostatic interaction between its amino groups with the negatively charged citrate stabilizer of AuNPs to form AuNP@3-APBA. Subsequently, the aggregation and visual color change of the assembled AuNP@3-APBA are induced by the covalent reaction between boronic acid ligands of 3-APBA and cis-diols of IHO. The developed assay presented a very simple operating procedure and a rapid analysis time of around 10 min. The developed assay also exhibited good selectivity and a low limit of detection (LOD) of 0.005 mM for detecting IHO. Moreover, the developed assay showed comparable accuracy and precision to the high-performance liquid chromatography-diode array detector (HPLC-DAD) method when used for the rapid determination of IHO in river water and human urine samples. The recoveries of IHO at three spiking levels were in the range of 91.5-106.3% with relative standard deviation (RSD) values below 6.39%.

Colorimetric detection of food freshness based on amine-responsive dopamine polymerization on gold nanoparticles

Biogenic amines (BAs) are not only well-known indicators for food freshness but can cause serious harm to the body after excessive consumption, which makes the determination of its content in food of great significance. In this work, a simple and convenient method for colorimetric detection of BAs was developed based on the sensitivity of the polymerization of dopamine to the presence of BAs on the surface of gold nanoparticles (AuNPs). Taking histamine as a representative, the system exhibited a distinct color change from wine red to black among the amine concentration of 1-100 μg/mL with the detection limit of 2.8 μg/mL. The detection system also exhibited sensitivity to other common kinds of BAs, such as putrescine, cadaverine, spermine, spermidine, tyramine, and tryptamine. Moreover, the proposed method showed encouraging performance in visual detection of the freshness of real samples, which provided a new approach for food quality and freshness evaluation.

Colorimetric and electrochemical detection of SARS-CoV-2 spike antigen with a gold nanoparticle-based biosensor

Since emerging in China in December 2019, COVID-19 has spread globally, wreaked havoc for public health and economies worldwide and, given the high infectivity and unexpectedly rapid spread of the virus responsible-that is, severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2)-urged the World Health Organization to declare it a pandemic. In response, reducing the virus's adverse effects requires developing methods of early diagnosis that are reliable, are inexpensive and offer rapid response. As demonstrated in this article, the colorimetric and electrochemical detection of SARS-CoV-2 spike antigen with gold nanoparticle-based biosensors may be one such method. In the presence of the SARS-CoV-2 spike antigen, gold nanoparticles aggregated rapidly and irreversibly due to antibody-antigen interaction and consequently changed in colour from red to purple, as easily observable with the naked eye or UV-Vis spectrometry by way of spectral redshifting with a detection limit of 48 ng/mL. Moreover, electrochemical detection was achieved by dropping developed probe solution onto the commercially available and disposable screen-printed gold electrode without requiring any electrode preparation and modification. The method identified 1 pg/mL of the SARS-CoV-2 spike antigen and showed a linear response to the SARS-CoV-2 spike antigen ranging from 1 pg/mL to 10 ng/mL. Both methods were highly specific to detecting the SARS-CoV-2 spike antigen but not other antigens, including influenza A (i.e. H1N1), MERS-CoV and Streptococcus pneumoniae, even at high concentrations.