Determination of pharmaceuticals, iodinated contrast media and musk fragrances in sludge by LC tandem MS and GC/MS

Fate of hormones and pharmaceuticals during combined anaerobic treatment and nitrogen removal by partial nitritation-anammox in vacuum collected black water

Vacuum collected black (toilet) water contains hormones and pharmaceuticals in relatively high concentrations (μg/L to mg/L range) and separate specific treatment has the potential of minimizing their discharge to surface waters. In this study, the fate of estrogens (natural and synthetical hormones) and pharmaceuticals (paracetamol, metoprolol, propranolol, cetirizine, doxycycline, tetracycline, ciprofloxacin, trimethoprim, carbamazepine, ibuprofen and diclofenac) in the anaerobic treatment of vacuum collected black water followed by nitrogen removal by partial nitritation-anammox was investigated. A new analytical method was developed to detect the presence of several compounds in the complex matrix of concentrated black water. Detected concentrations in black water ranged from 1.1 μg/L for carbamazepine to >1000 μg/L for paracetamol. Anaerobic treatment was only suitable to remove the majority of paracetamol (>90%). Metoprolol was partly removed (67%) during aerobic treatment. Deconjugation could have affected the removal efficiency of ibuprofen as concentrations even increased during anaerobic treatment and only after the anammox treatment 77% of ibuprofen was removed. The presence of persistent micro-pollutants (diclofenac, carbamazepine and cetirizine), which are not susceptible for biodegradation, makes the application of advanced physical and chemical treatment unavoidable.

Ethylenediamine-N,N'-diglutaric acid (EDDG) as a promising biodegradable chelator: quantification, complexation and biodegradation

[S,S]-ethylenediamine-N,N'-diglutaric acid (EDDG) has been gaining interest in the industrial sector as a promising chelator. In this study, the effective metal complexing capacity of EDDG over a wide pH range was modelled and its biodegradability assessed. Results showed that EDDG could effectively bind to several metallic ions in a wide pH range and was completely biodegraded after approximately 15 days by un-acclimatized sludge. To confirm its biodegradability, an accurate quantification method based on the combination of liquid chromatography and tandem quadrupole mass spectrometry (LC-MS/MS) was developed. Good linearity of the detector response was found for EDDG at concentrations ranging from 0.15 to 1.2 mg/L.

Elimination and fate of selected micro-organic pollutants in a full-scale anaerobic/anoxic/aerobic process combined with membrane bioreactor for municipal wastewater reclamation

The occurrence and elimination of 19 micro-organic pollutants including endocrine disrupting chemicals (EDCs) and pharmaceuticals and personal care products (PPCPs) in a full-scale anaerobic/anoxic/aerobic-membrane bioreactor process was investigated. The investigated process achieved over 70% removal of the target EDCs and 50%-100% removal of most of the PPCPs, with influent concentration ranging from ng/L to μg/L. Three PPCPs, carbamazepine, diclofenac and sulpiride were not well removed, with the removal efficiency below 20%. A rough mass balance suggests that the targets were eliminated through sludge-adsorption and/or biodegradation, the former of which was particularly significant for the removal of hydrophobic compounds. The two-phase fate model was employed to describe the kinetics of sludge-adsorption and biodegradation. It was found that the fast sludge adsorption (indicated by mass-transfer rates greater than 10 for most compounds) is responsible for the rapid decline of the aqueous concentration of the targets in the first compartment of the treatment process (i.e. in the anaerobic tank). In contrast, the slow biodegradation proved to be the rate-determining step for the entire degradation process, and the rates are generally positively related to the dissolved oxygen level. On the other hand, this study showed that the removal rates of most targets can reach a quasi-plateau in 5 h under aerobic conditions, indicating that hydraulic retention time of ca. 5 h in aerobic tanks should be sufficient for the elimination of most targets.

Determination of pharmaceuticals in biosolids using accelerated solvent extraction and liquid chromatography/tandem mass spectrometry

An analytical method was developed to quantitatively determine pharmaceuticals in biosolid (treated sewage sludge) from wastewater treatment plants (WWTPs). The collected biosolid samples were initially freeze dried, and grounded to obtain relatively homogenized powders. Pharmaceuticals were extracted using accelerated solvent extraction (ASE) under the optimized conditions. The optimal operation parameters, including extraction solvent, temperature, pressure, extraction time and cycles, were identified to be acetonitrile/water mixture (v/v 7:3) as extraction solvent with 3 extraction cycles (15 min for each cycle) at 100 °C and 100 bars. The extracts were cleaned up using solid-phase extraction followed by determination by liquid chromatography coupled with tandem mass spectrometry. For the 15 target pharmaceuticals commonly found in the environment, the overall method recoveries ranged from 49% to 68% for tetracyclines, 64% to 95% for sulfonamides, and 77% to 88% for other pharmaceuticals (i.e. acetaminophen, caffeine, carbamazepine, erythromycin, lincomycin and tylosin). The developed method was successfully validated and applied to the biosolid samples collected from WWTPs located in six cities in Michigan. Among the 15 target pharmaceuticals, 14 pharmaceuticals were detected in the collected biosolid samples. The average concentrations ranged from 2.6 μg/kg for lincomycin to 743.6 μg/kg for oxytetracycline. These results indicated that pharmaceuticals could survive wastewater treatment processes, and accumulate in sewage sludge and biosolids. Subsequent land application of the contaminated biosolids could lead to the dissemination of pharmaceuticals in soil and water environment, which poses potential threats to at-risk populations in the receiving ecosystems.

Current approaches to trace analysis of pharmaceuticals and personal care products in the environment

A large number of xenobiotics including pharmaceuticals and personal care products are continuously released into the environment. Effluents from sewage treatment plants are well known to be the major source for introduction of pharmaceuticals and personal care products into the aquatic system. In recent years, reliable methods have been established for residue analysis of these pollutants down to low ng/L levels. In this review, the different approaches to their trace determination are reviewed with special attention being paid to sample preparation procedures, state-of-the-art high-performance separation methods hyphenated with mass spectrometry, and immunochemical methods.

Occurrence of estrogens in sewage sludge and their fate during plant-scale anaerobic digestion

Estrogens, which contribute greatly to the endocrine-disrupting activity in sewage, are partially sorbed onto particulate matter during sewage treatment. We thus investigated the occurrence of estrogens in different kinds of sludge and throughout a plant-scale anaerobic digestion process. The analytical method was first validated when sorption interaction between spiked estrogens and sludge could occur. Hence, the recovery ratio of estrone (E1), 17beta-estradiol (E2), estriol (E3) and 17alpha-ethinylestradiol (EE2) were determined when added to liquid sludge and mixed under various conditions. We show that minor non-extractable residues were formed (5-10%), suggesting that the sorption interaction established with sludge did not limit estrogen extraction. Estrogen concentrations measured in collected samples varied with sludge type. Secondary sludge showed higher E1 contents than primary sludge: respectively, 43 and 8 ng g(-1) dry weight (dw). Two pathways of E1 production during secondary treatment are proposed to explain such a result. Higher estrogen concentrations were found in secondary sludge from a conventional plant (55 ng g(-1)dw) compared to those from an advanced plant (13 ng g(-1)dw). Based on estimated estrogen concentrations in sewage, we conclude that operating parameters play a role in the sorption of estrogens during secondary treatment. Also, the hydrophobic properties of the estrogens influenced the individual adsorption of each molecule. Thus, E3 showed the highest estimated concentrations in sewage but very low concentrations in sludge. Finally, plant-scale anaerobic digestion showed low efficiency (<40%) for removing estrogens and, regarding the final dewatering process, concentrations increased for E2 and EE2.

Occurrence of pharmaceuticals and hormones in sewage sludge

The present study evaluates the presence of nine hormones and their conjugates and 20 pharmaceuticals such as anti-inflammatories, lipid regulators, and antibiotics among others in sewage sludge from two sewage treatment plants (STPs) in the Tarragona area (Spain) for the period March 2007 until March 2008. Target analytes have been determined using different methods involving pressurized liquid extraction and liquid chromatography (electrospray ionization) tandem mass spectrometry (MS-MS). Most of the pharmaceuticals and hormones were found at low micrograms per kilogram dry weight levels in the sewage sludge samples analyzed. Some compounds were present in all samples, such as acetaminophen, caffeine, carbamazepine, and ibuprofen, among others. Other compounds, such as estriol, were found only in the STP of Reus. The compounds that showed the highest concentration in both STPs were roxithromycin and tylosin (1,446 and 1,958 microg/kg dry wt, respectively). The presence of these compounds in sewage sludge demonstrated that they are partially or totally removed from the influent wastewater by sorption into the sewage sludge.

Psychiatric pharmaceuticals in the environment

Psychiatric pharmaceuticals, such as anxiolytics, sedatives, hypnotics, and antidepressants, are among the most prescribed active substances throughout the world. The occurrence of these widely used compounds in environmental matrices (wastewaters, surface, ground and drinking waters, soils, sediments, bio-solids and tissue), as well as the first studies indicating their high persistence and toxicity to non-target organisms, justify the growing concern about these emerging environmental pollutants. Despite this increasing interest, there is a considerable lack of knowledge about the environmental fate of a large number of psychiatric pharmaceuticals and further research about this topic is needed. This paper aims to review the literature data related to the occurrence, persistence, environmental fate and toxicity for non-target organisms of this group of pharmaceuticals. The analytical methods developed for the determination of psychiatric medicines in environmental matrices are also highlighted.

Multi-residue method for trace level determination of pharmaceuticals in solid samples using pressurized liquid extraction followed by liquid chromatography/quadrupole-linear ion trap mass spectrometry

A simple and sensitive method for simultaneous analysis of 43 pharmaceutical compounds in sewage sludge and sediment samples was developed and validated. The target compounds were extracted using pressurized liquid extraction (PLE) and then purified and pre-concentrated by solid phase extraction (SPE) using a hydrophilic-lipophilic balanced polymer. PLE extraction was performed on temperature of 100 degrees C, with methanol/water mixture (1/2, v/v) as extraction solvent. The quantitative analysis was performed by liquid chromatography tandem mass spectrometry using a hybrid triple quadrupole-linear ion trap mass spectrometer (LC-QqLIT-MS). Data acquisition was carried out in selected reaction monitoring (SRM) mode, monitoring two SRM transitions to ensure an accurate identification of target compounds in the samples. Additional identification and confirmation of target compounds were performed using the Information Dependent Acquisition (IDA) function. The method was validated through the estimation of the linearity, sensitivity, repeatability, reproducibility and matrix effects. The internal standard approach was used for quantification because it efficiently corrected matrix effects. Despite the strong matrix interferences, the recoveries were generally higher of 50% in both matrixes and the detection and quantification limits were very low. Beside the very good sensitivity provided by LC-QqLIT-MS, an important characteristic of the method is that all the target compounds can be simultaneously extracted, treated and analysed. Hence, it can be used for routine analysis of pharmaceuticals providing large amount of data. The method was applied for the analysis of pharmaceuticals in river sediment and wastewater sludge from three treatment plants with different treatment properties (i.e. capacity, secondary treatment, quality of influent waters). The analysis showed a widespread occurrence of pharmaceuticals in the sludge matrices.

Mass flows of X-ray contrast media and cytostatics in hospital wastewater

Little is known about the significance of hospitals as point sources for emission of organic micropollutants into the aquatic environment. A mass flow analysis of pharmaceuticals and diagnostics used in hospitals was performed on the site of a representative Swiss cantonal hospital. Specifically, we analyzed the consumption of iodinated X-ray contrast media (ICM) and cytostatics in their corresponding medical applications of radiology and oncology, respectively, and their discharge into hospital wastewater and eventually into the wastewater of the municipal wastewater treatment plant. Emission levels within one day and over several days were found to correlate with the pharmacokinetic excretion pattern and the consumed amounts in the hospital during these days. ICM total emissions vary substantially from day to day from 255 to 1259 g/d, with a maximum on the day when the highest radiology treatment occurred. Parent cytostatic compounds reach maximal emissions of 8-10 mg/d. A total of 1.1%, 1.4%, and 3.7% of the excreted amounts of the cytostatics 5-fluorouracil, gemcitabine, and 2',2'-difluorodeoxyuridine (main metabolite of gemcitabine), respectively, were found in the hospital wastewater, whereas 49% of the total ICM was detected, showing a high variability among the compounds. These recoveries can essentially be explained by the high amount administered to out-patients (70% for cytostatics and 50% for ICM); therefore, only part of this dose is expected to be excreted on-site. In addition, this study emphasizes critical issues to consider when sampling in hospital sewer systems. Flow proportional sampling over a longer period is crucial to compute robust hospital mass flows.

Simultaneous determination of fluoroquinolones, sulfonamides and tetracyclines in sewage sludge by pressurized liquid extraction and liquid chromatography electrospray ionization-mass spectrometry

A new scheme for the quantitative determination of traces of fluoroquinolones (FQs), tetracyclines (TCs) and sulfonamides (SAs) in sewage sludge was developed. The compounds were simultaneously extracted from sewage sludge by pressurized liquid extraction (PLE). A novel and effective method for PLE was developed. Solid-phase extraction was used for cleaning up the extracts. Identification and quantification of the compounds was done using high-performance liquid chromatography with electrospray ionization mass spectrometry in selected reaction monitoring mode. The best recovery of FQs and TCs was obtained by using hydrophilic-lipophilic balance cartridges, recoveries ranged 59% for norfloxacin to 82% for ofloxacin and 95% for doxycycline; for SAs strong cation-exchange cartridges were more efficient, recoveries were 96% for sulfamethoxazole and 43% for sulfadimethoxine. Limit of quantification ranged from 0.1 ng/g for SAs to 160 ng/g for tetracycline. Method precision for TCs was 5.06% and 1.12%, and for SAs 0.43% and 2.01%. FQs precision ranged from 0.77% to 1.89%.

Effects of ozone pre-treatment on diclofenac: intermediates, biodegradability and toxicity assessment

Diclofenac (DCF), a common analgesic, anti-arthritic and anti-rheumatic drug, is one of the most frequently detected compounds in water. This study deals with the degradation of diclofenac in aqueous solution by ozonation. Biodegradability (BOD(5)/COD ratio and Zahn-Wellens test), acute ecotoxicity and inhibition of activated sludge activity were determined in ozonated and non-ozonated samples. Liquid chromatography coupled with time-of-flight mass spectrometry (LC/TOF-MS) was used to identify the intermediates formed in 1 h of ozonation. Eighteen intermediates were identified by these techniques and a tentative degradation pathway for DCF ozonation is proposed. Experimental results show that ozone is efficient at removing DCF: >99% removal (starting from an initial concentration of 0.68 mmol L(-1)) was achieved after 30 min of ozonation (corresponding to an absorbed ozone dose of 0.22 g L(-1), which is 4.58 mmol L(-1)). However, only 24% of the substrate was mineralized after 1 h of ozonation. The biodegradability, respiration inhibition in activated sludge and acute toxicity tests demonstrate that ozonation promotes a more biocompatible effluent of waters containing DCF.

Multi-residue analysis and ultra-trace quantification of 36 priority substances from the European Water Framework Directive by GC-MS and LC-FLD-MS/MS in surface waters

A multi residue analysis was developed for screening, quantification and confirmation of 36 priority organic compounds included in the 2000/60/EC European Water Framework Directive. The compounds analyzed included 19 pesticides, 8 PAH, 5 endocrine-disruptors and 4 organochlorine compounds. The method was developed in three steps. First, automated off-line solid-phase extraction using Strata X cartridges was optimized to trap simultaneously the 36 studied compounds. Second, the more volatile compounds were analysed by gas chromatography coupled to mass spectrometry with electron impact ionisation in selected ion monitoring mode (SIM). Third, the last 20 compounds were detected and quantified, in one run, by liquid chromatography coupled to fluorescence detector and tandem mass spectrometry. The excellent selectivity and sensitivity allowed us satisfactory quantification and confirmation at levels as low as 0.2-67 ng L(-1) with recoveries between 59 and 105%. Such methodology was then applied to French surface waters: all the waters present organic contaminants, and their concentration varied according to the origin and nature of substances.

Optimisation of pressurised liquid extraction by experimental design for quantification of pesticides and alkyl phenols in sludge, suspended materials and atmospheric fallout by liquid chromatography-tandem mass spectrometry

The study proposes an analytical method to quantify 10 alkylphenols and 12 pesticides at ultra-trace levels by liquid chromatography in reverse mode coupled to positive electrospray ionisation-tandem mass spectrometry. The extraction procedure from environmental solids was optimised by pressurised liquid extraction using acetonitrile:isopropanol (1:1, v/v). The influence of several extraction experimental factors, temperature, pressure, duration and number of cycles, related to the PLE was investigated by an original and efficient chemometric approach. The optimised extraction method (80 degrees C, 40 bar, 10 min, 1 cycle) exhibited recoveries between 67 and 127% with RSD mostly under 13%. The whole method was applied to real samples: sludge, suspended materials, atmospheric fallouts and roof deposit. Pollutant levels were between 1 microg kg(-1) and 5.9 mg kg(-1).

Fate and distribution of pharmaceuticals in wastewater and sewage sludge of the conventional activated sludge (CAS) and advanced membrane bioreactor (MBR) treatment

In this paper we report on the performances of full-scale conventional activated sludge (CAS) treatment and two pilot-scale membrane bioreactors (MBRs) in eliminating various pharmaceutically active compounds (PhACs) belonging to different therapeutic groups and with diverse physico-chemical properties. Both aqueous and solid phases were analysed for the presence of 31 pharmaceuticals included in the analytical method. The most ubiquitous contaminants in the sewage water were analgesics and anti-inflammatory drugs ibuprofen (14.6-31.3 microg/L) and acetaminophen (7.1-11.4 microg/L), antibiotic ofloxacin (0.89-31.7 microg/L), lipid regulators gemfibrozil (2.0-5.9 microg/L) and bezafibrate (1.9-29.8 microg/L), beta-blocker atenolol (0.84-2.8 microg/L), hypoglycaemic agent glibenclamide (0.12-15.9 microg/L) and a diuretic hydrochlorothiazide (2.3-4.8 microg/L). Also, several pharmaceuticals such as ibuprofen, ketoprofen, diclofenac, ofloxacin and azithromycin were detected in sewage sludge at concentrations up to 741.1, 336.3, 380.7, 454.7 and 299.6 ng/g dry weight. Two pilot-scale MBRs exhibited enhanced elimination of several pharmaceutical residues poorly removed by the CAS treatment (e.g., mefenamic acid, indomethacin, diclofenac, propyphenazone, pravastatin, gemfibrozil), whereas in some cases more stable operation of one of the MBR reactors at prolonged SRT proved to be detrimental for the elimination of some compounds (e.g., beta-blockers, ranitidine, famotidine, erythromycin). Moreover, the anti-epileptic drug carbamazepine and diuretic hydrochlorothiazide by-passed all three treatments investigated. Furthermore, sorption to sewage sludge in the MBRs as well as in the entire treatment line of a full-scale WWTP is discussed for the encountered analytes. Among the pharmaceuticals encountered in sewage sludge, sorption to sludge could be a relevant removal pathway only for several compounds (i.e., mefenamic acid, propranolol, and loratidine). Especially in the case of loratidine the experimentally determined sorption coefficients (Kds) were in the range 2214-3321 L/kg (mean). The results obtained for the solid phase indicated that MBR wastewater treatment yielding higher biodegradation rate could reduce the load of pollutants in the sludge. Also, the overall output load in the aqueous and solid phase of the investigated WWTP was calculated, indicating that none of the residual pharmaceuticals initially detected in the sewage sludge were degraded during the anaerobic digestion. Out of the 26 pharmaceutical residues passing through the WWTP, 20 were ultimately detected in the treated sludge that is further applied on farmland.

Distribution and elimination of polycyclic musks in three sewage treatment plants of Beijing, China

The two representative polycyclic musks, 1-(5,6,7,8-tetrahydro-3,5,5,6,8,8-hexamethyl-2-naphthenyl)-ethanone (AHTN) and 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethylcyclopenta[g]-2-benzopyrane (HHCB), were measured in aqueous samples and sludge samples of three sewage treatment plants (STPs) in Beijing, China using a gas chromatograph-mass spectrometry. The HHCB and AHTN concentration ranges in the influents were 1251.4-3003.8 ng/L and 111.9-286.3 ng/L, respectively. Meanwhile, the ranges of 492.8-1285.3 ng/L for HHCB and 47.3-89.3 ng/L for AHTN were present in the effluents. The musks in the sludges were three to four orders of magnitude higher than those in aqueous sewages. The removal efficiencies of the two musks varied in the ranges of 41.7%-70.1% for HHCB, and 25.5%-68.8% for AHTN. Adsorption onto suspended particulate matter played an important role in removing musks from the sewages. The HHCB/AHTN ratio along the treatment processes showed that the two musks had high similarity of removal from sewage by each reactor in STP. The musks in the effluent sewages may pose a low potential risk to aquatic environment in terms of the predicted-non-effect concentration. Nevertheless, considering the possible additive and synergistic effects with other compounds emitted via STPs, their bioconcentration and bioaccumulation in aquatic organisms and so on, it is essential to monitor these compounds in various compartments and to study their environmental fate.

Simultaneous determination of pharmaceuticals, endocrine disrupting compounds and hormone in soils by gas chromatography-mass spectrometry

Analytical methods have been developed for simultaneous determination of six different pharmaceuticals and personal care products (PPCPs) (clofibric acid, ibuprofen, naproxen, ketoprofen, diclofenac, and triclosan), three endocrine disrupting compounds (EDCs) (4-tert-octylphenol, 4-n-nonylphenol, and bisphenol A (BPA)) and one estrogenic compound (estrone) in soil matrix. The soils were extracted by different solvents with the help of an ultrasonic treatment at 42 kHz, followed by a solid phase extraction (SPE) as a cleanup procedure. The purified extracts were derivatized with N-methyl-N-(tert-butyldimethylsilyl) trifluoroacetamide (MTBSTFA) and then analyzed by GC-MSD (SIM mode). The method was evaluated by testing the following variables: initial spiking levels, extraction solvents, solvent volumes, and soil types (sandy and clay soils). For 5 g of soil, four successive extraction steps with the mixture of acetone-ethyl acetate provided satisfactory recoveries. In the sandy soil, the recoveries of all the compounds were from 63.8 to 110.7% for the spiking level of 100 ng/g dry soil, and from 52.2 to 108.2% for 5 ng/g dry soil, respectively. Result was similar for the clay soil. The precision across all recoveries was high, suggesting that this method has a good reproducibility. The method was successfully employed to soil samples collected from a golf course irrigated with reclaimed wastewater in southern California, and resulted in the detection of clofibric acid, ibuprofen, naproxen, triclosan, bisphenol A, and estrone at ng per gram dry weight concentration levels. The method is robust and simple, and provides straightforward analyses of these current-emerging trace organic pollutants in solid matrices.

Runoff of pharmaceuticals and personal care products following application of biosolids to an agricultural field

Municipal biosolids are a source of nutrients for crop production. Beneficial Management Practices (BMPs) can be used to minimize the risk of contamination of adjacent water resources with chemical or microbial agents that are of public or environmental health concern. In this field study, we applied biosolids slurry at a commercial rate using either subsurface injection or broadcast application followed by incorporation. Precipitation was simulated at 1, 3, 7, 22, 36 and 266 days post-application on 2 m(2) microplots to evaluate surface runoff of 9 model pharmaceuticals and personal care products (PPCPs), atenolol, carbamazepine, cotinine, gemfibrozil, naproxen, ibuprofen, acetaminophen, sulfamethoxazole and triclosan. In runoff from the injected plots, concentrations of the model PPCPs were generally below the limits of quantitation. In contrast, in the broadcast application treatment, the concentrations of atenolol, carbamazepine, cotinine, gemfibrozil, naproxen, sulfamethoxazole and triclosan on the day following application ranged from 70-1477 ng L(-1) in runoff and generally declined thereafter with first order kinetics. The total mass of PPCPs mobilized in surface runoff per m(2) of the field ranged from 0.63 microg for atenolol to 21.1 microg for ibuprofen. For ibuprofen and acetaminophen, concentrations in runoff first decreased and then increased, suggesting that these drugs were initially chemically or physically sequestered in the biosolids slurry, and subsequently released in the soil. Carbamazepine and triclosan were detected at low concentrations in a runoff event 266 days after broadcast application. Overall, this study showed that injection of biosolids slurry below the soil surface could effectively eliminate surface runoff of PPCPs.

GC-MS analysis of organic compounds in wastewater and sewage sludge

A multimethod based on liquid-liquid extraction and solid-liquid extraction for the analysis of persistent organic pollutants in water and sludge from sewage treatment plants has been established. Traces of 22 organic compounds used in industry and personal care products (PCPs) were analyzed by GC/MS. The LODs for the analytes were less than 2.3 ng/L for wastewater and 31 microg/kg (dry weight matter) for sewage sludge. Satisfactory recoveries (70-130%) were achieved. The validated method permits the analysis of water and sludge samples at various stages of the treatment from different sewage treatment plants. Thus, the distribution between water and sludge as well as the dissipation of the compounds analyzed were balanced. By this means, the efficiency of different wastewater treatment plants (WWTPs) can be evaluated and measures can be taken to optimize the treatment process at different stages.

Determination of the solid-water distribution coefficient (Kd) for pharmaceuticals, estrogens and musk fragrances in digested sludge

This work determined the solid-water distribution coefficient (K(d)) and the organic carbon normalized distribution coefficient (K(oc)) of several pharmaceuticals (carbamazepine, ibuprofen, naproxen, diclofenac, iopromide, sulfamethoxazole and roxithromycin), three estrogens (estrone, 17beta-estradiol and 17alpha-ethinylestradiol) and two musk fragrances (HHCB and AHTN) in digested sludge. These sorption coefficients can be used to evaluate the fate of these substances during sludge treatment, thus avoiding the expensive and time-consuming analysis in the sludge phase. For determining the K(d) and K(oc) values of the target compounds in digested sludge, their concentrations were measured in the aqueous and solid phase of the effluent of an anaerobic digestion pilot plant run at several operational conditions. The results obtained were compared with the values modelled by using simple K(ow) approaches. The resulting log K(d) values ranged between 3.5 and 4.4 for the two musk fragrances (log K(oc) of 4.5-6.0), between 2.1 and 2.9 for estrogens (log K(oc) of 2.9-4.2) and between 0.8 and 1.9 for the remaining pharmaceuticals (log K(oc) of 1.8-3.5). These values are in the same range as those reported in the literature for primary and secondary sludge and no significant influence of the anaerobic digestion operational conditions was observed. For most compounds, the modelled K(oc) were close or within the lower range of the experimentally determined K(oc). Major deviations of the modelled K(oc) values were found for iopromide, sulfamethoxazole and roxithromycin, which were 1-3 orders of magnitude lower than the measured values.

Microwave-assisted extraction of organophosphate flame retardants and plasticizers from indoor dust samples

A procedure for the determination of eight organophosphate flame retardants and plasticizers in dust samples is presented. Microwave-assisted extraction and gas chromatography (GC) with nitrogen-phosphorus detection (NPD) were used for sample preparation and analytes quantification, respectively. Influence of different variables (type and volume of organic solvent, temperature, time, agitation, etc.) on the yield of the extraction step was evaluated. The most important factor was the type of solvent, with the highest efficiencies corresponding to acetone. Under final conditions 10 mL of this solvent were employed. The extraction was carried out at 130 degrees C and satisfactory yields, similar to those obtained with the Soxhlet technique, were achieved. Due to the high content of organic carbon in dust samples, primary acetone extracts had to be subjected to intensive clean-up. Dilution with ultrapure water followed by concentration on a reversed-phase sorbent and further purification using silica, allowed a significant reduction of co-extracted interferences. Application of the developed methodology to indoor dust from private houses showed important concentrations of several organophosphate esters. The highest levels, up to 19 microg/g, corresponded to tris(butoxyethyl) phosphate; moreover, average values of two chlorinated compounds, used as flame retardants and considered as the most concerning species in the group, exceeded the 1 microg/g level.

Novel analytical procedures for screening of drug residues in water, waste water, sediment and sludge

Traces of pharmaceuticals are continuously introduced into the aquatic environment mainly by sewage treatment plant effluents. Final data about their impact on the ecosystem are still partly missing. Progress in instrumental analytical chemistry has resulted in the availability of methods that allow a monitoring of these pollutants at ng L(-1) levels. In this review the state-of-the-art of residue analysis of pharmaceuticals by chromatographic and electrophoretic techniques is summarized. Improvements in detection limits over the past years have mainly been due to sophisticated mass spectrometric detection techniques. Furthermore, robust sample preparation and preconcentration protocols based on solid-phase extraction and related procedures have contributed significantly to the achievements observed so far. This review also covers several immunochemical approaches which may serve as an inexpensive alternative for quick screening of samples.

Mass spectrometry for monitoring micropollutants in water

Surface water reservoirs and aquifers are exposed to contamination by thousands of micropollutants from industrial, pharmaceutical, agricultural and natural origins. Most developed and developing countries implement a water-quality regulation programme to prevent contamination by such chemicals at illegal concentrations. Traditionally, analytical methods based on gas chromatography-mass spectrometry or liquid chromatography with UV/fluorescence detection were used to monitor water quality. These methods require multistep sample preparation and several have low specificity. Nowadays, liquid chromatography tandem mass spectrometry has become a key technique for environmental analysis, allowing the detection of a wide range of polar and nonvolatile compounds. The use of this method has increased the specificity and confidence of identification, while reducing sample preparation to a minimum.

Elimination of selected acidic pharmaceuticals from municipal wastewater by an activated sludge system and membrane bioreactors

The elimination of six acidic pharmaceuticals (clofibric acid, diclofenac, ibuprofen, ketoprofen, mefenamic acid, and naproxen) in a real wastewater treatment plant (WWTP) using an activated sludge system and membrane bioreactors (MBRs) was investigated by using a gas chromatography/mass spectrometry (GC/MS) system for measurement of the compounds. Limited information is available for some of the tested pharmaceuticals at present. Solid retention times (SRTs) of the WWTP and the two MBRs were 7, 15, and 65 days, respectively. The elimination rates varied from compound to compound. The MBRs exhibited greater elimination rates for the examined pharmaceuticals than did the real plant. Dependency of the elimination rates of the pharmaceuticals on SRTs was obvious; the MBR operated with a longer SRT of 65 days clearly showed better performance than did the MBR with a shorter SRT of 15 days. The difference between the two MBRs was particularly significant in terms of elimination of ketoprofen and diclofenac. Measurements of the amounts of adsorbed pharmaceuticals on the sludge and aerobic batch elimination experiments were carried out to investigate the elimination pathways of the pharmaceuticals. Results of the batch elimination tests revealed that the sludges in the MBRs had large specific sorption capacities mainly due to their large specific surface areas. Despite the sorption capacities of sludges, the main mechanism of elimination of the pharmaceuticals in the investigated processes was found to be biodegradation. Biodegradation of diclofenac, which has been believed to be refractory to biodegradation, seemed to occur very slowly.

Fate of pharmaceutical and personal care products (PPCPs) during anaerobic digestion of sewage sludge

The behaviour of 13 pharmaceutical and personal care products (PPCPs) has been studied during anaerobic digestion of sewage sludge: two musks (Galaxolide and Tonalide), one tranquilliser (Diazepam), one anti-epileptic (Carbamazepine), three anti-phlogistics (Ibuprofen, Naproxen and Diclofenac), two antibiotics (Sulfamethoxazole and Roxithromycin), one X-ray contrast medium (Iopromide) and three oestrogens (Estrone, 17beta-oestradiol and 17alpha-ethinyloestradiol). Two parallel processes have been carried out, one in mesophilic range (37 degrees C) and the other in thermophilic range (55 degrees C). The influence of temperature and sludge retention time (SRT) has been analysed. Among the substances considered, the higher removal efficiencies were achieved for the antibiotics, natural oestrogens, musks and Naproxen. For the other compounds, the values ranged between 20% and 60%, except for Carbamazepine, which showed no elimination. The removal of oestrogens, Diazepam and Diclofenac occurred after sludge adaptation. In general, no influence of SRT and temperature on PPCPs removal was observed. Considering the difficulty of obtaining reliable PPCPs concentrations, especially those corresponding to the fractions sorbed onto sludge, a methodology to validate the experimental data has been developed and successfully applied.

Pressurized liquid extraction of pharmaceuticals from sewage-sludge

A method for the quantitative determination of ten pharmaceuticals in sewage sludge was developed by using pressurized liquid extraction (PLE) and HPLC-MS with ESI (HPLC-(ESI)MS). The PLE was optimized with regard to solvents and operational parameters, such as temperature, pressure, extraction time, and purge time. The optimum conditions were: 50 mM phosphoric acid/methanol (1:1 v/v) as the extraction solvent, temperature of 100 degrees C, pressure of 100 bar, extraction time 15 min, 2 cycles, flush volume 150% and purge time 300 s. All recoveries for pharmaceuticals were over 68% except for salicylic acid. The repetitivity and reproducibility between days expressed as RSD was lower than 8% for repetitivity and 10% for reproducibility. The LOD of all compounds was lower than 10 microg/kg of dry weight of sewage sludge. The method was applied to determine the pharmaceuticals in sewage sludge from two domestic sewage treatment plants (STPs). The samples were collected every three months between February 2004 and June 2005. Some pharmaceuticals were determined in the samples and naproxen showed the highest value (242 microg/kg of dry weight).

Pharmaceutical determination in surface and wastewaters using high-performance liquid chromatography-(electrospray)-mass spectrometry

A method was developed to determine 11 pharmaceutical compounds in water samples. The method uses SPE and HPLC coupled to MS (LC/MS) using ESI in both positive and negative modes. Three different sorbents were compared for the extraction of analytes from river and sewage treatment plant (STP) waters and OASIS HLB provided the best results. For the solid-phase extraction of 500 mL of river water samples, the recoveries were between 41 and 101% with the exception of acetaminophen, salicylic acid and naproxen. The LODs were between 3 and 5 ng/L for all the compounds, except naproxen which had an LOD of 15 ng/L. Acetaminophen, caffeine, carbamazepine, bezafibrate and ibuprofen were found in three of the tested river samples at ng/L levels and among them, the highest values were for caffeine and bezafibrate with 305 and 363 ng/L, respectively. For the influent and effluent water samples of the STP, volumes of 100 and 250 mL were used, respectively, to obtain acceptable recoveries. All the compounds showed recoveries between 33 and 91% for effluent samples and 33-72% for influent samples, with the exception of acetaminophen, salicylic acid and bezafibrate, which had lower recoveries. The method developed enabled pharmaceuticals in the influent and effluent sewage waters to be determined in five campaigns carried out between February 2004 and June 2005. Several pharmaceuticals were found in the influent samples: for instance, maximum concentrations of ibuprofen and caffeine were 6 and 40 microg/L, respectively.

Influence of ozone pre-treatment on sludge anaerobic digestion: removal of pharmaceutical and personal care products

The effect of an oxidative pre-treatment with ozone on the removal of Pharmaceutical and Personal Care Products (PPCPs) during the anaerobic digestion of sewage sludge has been investigated. Besides, the digested sludge characteristics in terms of pathogens content, dewatering properties, heavy metals content and linear alkylbenzene sulfonates (LAS) were determined. During ozonation (20mg O(3)/g TSS), about 8% of volatile solids (VS) and 60% of the chemical oxygen demand (COD) were solubilized. However, no mineralization was observed. The elimination of VS and total COD during anaerobic digestion were not affected by ozone treatment with efficiencies ranging from 60% to 65%. All PPCPs considered were removed during anaerobic treatment of sludge, with efficiencies ranging from 20% to 99%. No significant influence of ozone pre-treatment was observed on PPCPs elimination except for carbamazepine. Pathogens, heavy metals and LAS contents after conventional and pre-ozonation treatment of sewage sludge were below the legal requirements. However, the dewatering properties of sludge were deteriorated when the ozone pre-treatment was applied.

Analysis of pharmaceuticals in fish using liquid chromatography-tandem mass spectrometry

A liquid chromatography-tandem mass spectrometry (LC-MS/MS) screening method has been developed targeting 23 pharmaceuticals and 2 metabolites with differing physicochemical properties in fish tissue. Reversed-phase separation of target compounds was achieved using a C18 column and a nonlinear gradient consisting of 0.1% (v/v) formic acid and methanol. Eluted analytes were introduced into the mass analyzer using positive or negative electrospray ionization, as appropriate. A variety of extraction solvents, differing in polarity, pH, or both, were investigated in order to assess recovery of target compounds from 1-g tissue homogenates. Among 10 solvents tested, a 1:1 mixture of 0.1 M aqueous acetic acid (pH 4) and methanol was identified as optimal, resulting in extraction recoveries for 24 of 25 compounds exceeding 60%. Tissue extracts were found to influence the LC-MS/MS response for several analytes. Consequently, matrix-matched calibration standards were employed to determine analyte concentrations in environmental samples. Statistically derived method detection limits were <6 ng/g for most analytes. The method was subsequently used to screen for target analytes in fish from an effluent-dominated stream. Diphenhydramine, diltiazem, carbamazepine, and norfluoxetine were detected in 11 of 11 environmental samples at concentrations ranging from 0.11 to 5.14 ng/g.

Calculation methods to perform mass balances of micropollutants in sewage treatment plants. application to pharmaceutical and personal care products (PPCPs)

Two different methods are proposed to perform the mass balance calculations of micropollutants in sewage treatment plants (STPs). The first method uses the measured data in both liquid and sludge phase and the second one uses the solid-water distribution coefficient (Kd) to calculate the concentrations in the sludge from those measured in the liquid phase. The proposed methodologies facilitate the identification of the main mechanisms involved in the elimination of micropollutants. Both methods are applied for determining mass balances of selected pharmaceutical and personal care products (PPCPs) and their results are discussed. In that way, the fate of 2 musks (galaxolide and tonalide), 3 pharmaceuticals (ibuprofen, naproxen, and sulfamethoxazole), and 2 natural estrogens (estrone and 17beta-estradiol) has been investigated along the different water and sludge treatment units of a STP. Ibuprofen, naproxen, and sulfamethoxazole are biologically degraded in the aeration tank (50-70%), while musks are equally sorbed to the sludge and degraded. In contrast, estrogens are not removed in the STP studied. About 40% of the initial load of pharmaceuticals passes through the plant unaltered, with the fraction associated to sludge lower than 0.5%. In contrast, between 20 and 40% of the initial load of musks leaves the plant associated to solids, with less than 10% present in the final effluent. The results obtained show that the conclusions concerning the efficiency of micropollutants removal in a particular STP may be seriously affected by the calculation method used.

Sample storage and extraction efficiencies in determination of polycyclic and nitro musks in sewage sludge

Analytical technology is continuously improving, developing better methods for isolating and concentrating trace compounds in environmental samples. Polycyclic and nitro musks (PNMs) are one group of emerging trace compounds detected in municipal wastewater. Differences in sample storage, preparation, and extraction methods for their measurement have led to variability in results. We analyzed 11 PNMs by GC/MS and compared the results of different storage times and extraction methods (supercritical fluid (SFE) or microwave-assisted (MAE)) for 202 samples of primary sludge, waste activated sludge (WAS), raw sludge, and aerobically/anaerobically digested biosolids collected from Canadian municipal wastewater treatment plants. Sixty-three air-dried samples were extracted by SFE, and 139 air-dried, centrifuged, or filtered samples were extracted by MAE. The mean surrogate recoveries were 89% (standard deviation (SD)=11%) for d(10)-anthracene by SFE and 88% (SD=14%) for d(10)-phenanthrene by MAE. Storage study results showed that PNM concentrations changed by a mean of 7% and 9% for primary sludge and WAS respectively after four weeks and decreased up to 25% after 13.5 months of storage in amber glass containers at -18 degrees C. Air-drying of sludge at room temperature caused losses of about 50% of PNM concentrations compared to centrifugation. The proportions of PNMs present in the liquid phase of sludge samples were less than 5% compared to proportions in the sludge solids. The most complete liquid-solid separation was achieved by filtration of frozen/thawed sludge samples, producing a liquid phase that contained less than 1% of the total musk content of the sample.