Occurrence of selected surfactants in untreated and treated sewage

Removal of surfactants nonylphenol ethoxylates from municipal sewage-comparison of an A/O process and biological aerated filters

The concentrations of nonylphenol ethoxylates (NPnEO, n=1 to 2) and nonylphenol (NP) in water and sludge samples were measured from a full scale sewage treatment plant (STP) with an Anaerobic/Oxic (A/O) and a Biological Aerated Filter (BAF) process. The A/O process was found to exhibit improved performance in comparison to the BAF process. Mean values of NP, NP1EO and NP2EO concentrations in influents from the STP were similar, ranging from 1.8 to 2.0×10(3)ngL(-1). In the A/O process, the removal efficiency of NP, NP1EO and NP2EO from the aqueous phase was 78%, 84%, and 89%, respectively. In contrast, the removal efficiencies of NP, NP1EO, and NP2EO were relatively lower for the BAF process, at 55%, 76%, and 79%, respectively. High concentrations of NP, NP1EO and NP2EO detected in the sludge samples had a maximum value of 2.7μgg(-1) dw, which indicates that improvement in the overall elimination of NP, NP1EO and NP2EO may be associated with adsorption by the sludge. To further investigate the fate of NP, NP1EO and NP2EO in the STP, our research assessed the degradation characteristics of NP by calculating its transformational loss in the STP. The results demonstrate that the quantity of NP measured in the effluent from the oxic unit increased by 32%, which indicates that NP1EO and NP2EO may undergo degradation in the oxic conditions.

Adsorption of the disinfectant benzalkonium chloride on montmorillonite. Synergistic effect in mixture of molecules with different chain lengths

The biocide benzalkonium chloride (BAC) is a mix of cationic alkylbenzyldimethylammonium surfactants having different alkyl chain lengths. A comparative study of adsorption on the phyllosilicate clay montmorillonite of two of these surfactants, with alkyl chains having respectively 12 C atoms (BAC-12) and 14 C atoms (BAC-14), and a mixture of both surfactants is presented in this work. Adsorption isotherms were performed for individual surfactants and for a 1:1 mixture BAC-12+BAC-14. The adsorption was investigated in an ample concentration range that covers almost seven orders of magnitude in concentrations (from 1 nM to 10 mM), range that includes environmentally relevant concentrations. Quantification of BAC was performed by HPLC-UV and LC-MS and the results were completed with powder X-Ray diffraction. The adsorption of both surfactants leads to adsorption isotherms with two well differentiated steps. The first step corresponds almost exclusively to a cation exchange process, and the binding constant is very similar for both surfactants. The second step of the isotherms is observed at higher concentrations and adsorption is mainly driven by lateral interactions between surfactant molecules. The binding constant of this step is larger for BAC-14 than for BAC-12. Adsorption from a BAC-12+BAC-14 mixture shows a synergistic behaviour, possibly due to a better packing arrangement in the interlayer. Calculations show that in natural systems silicate clays are major sorbents of BAC at low concentrations whereas binding to humic acid is predominant at high concentrations.

Evolution of the sewage treatment plant model SimpleTreat: use of realistic biodegradability tests in probabilistic model simulations

Given the large number of chemicals under regulatory scrutiny, models play a crucial role in the screening phase of the environmental risk assessment. The sewage treatment plant (STP) model SimpleTreat 3.1 is routinely applied as part of the European Union System for the Evaluation of Substances to estimate the fate and elimination of organic chemicals discharged via sewage. SimpleTreat estimates tend to be conservative and therefore only useful for lower-tier assessments. A probabilistic version of SimpleTreat was built on the updated version of the model (SimpleTreat 3.2, presented in a parallel article in this issue), embracing likeliest as well as worst-case conditions in a statistically robust way. Probabilistic parameters representing the variability of sewage characteristics, STP design, and operational parameters were based on actual STP conditions for activated sludge plants in Europe. An evaluation study was carried out for 4 chemicals with distinct sorption and biodegradability profiles: tonalide, triclosan, trimethoprim, and linear alkylbenzene sulfonate. Simulations incorporated information on biodegradability simulation studies with activated sludge (OECD 314B and OECD 303A tests). Good agreement for both median values and variability ranges was observed between model estimates and monitoring data. The uncertainty analysis highlighted the importance of refined data on partitioning and biodegradability in activated sludge to achieve realistic estimates. The study indicates that the best strategy to refine the exposure assessment of down-the-drain chemicals is by integrating higher-tier laboratory data with probabilistic STP simulations and, if possible, by comparing them with monitoring data for validation.

Efficiencies of freshwater and estuarine constructed wetlands for phenolic endocrine disruptor removal in Taiwan

We examined the distribution and removal efficiencies of phenolic endocrine disruptors (EDs), namely nonylphenol diethoxylates (NP2EO), nonylphenol monoethoxylates (NP1EO), nonylphenol (NP), and octylphenol (OP), in wastewater treated by estuarine and freshwater constructed wetland systems in Dapeng Bay National Scenic Area (DBNSA) and along the Dahan River in Taiwan. Water samples were taken bimonthly at 30 sites in three estuarine constructed wetlands (Datan, Pengcun and Linbian right bank (A and B)) in DBNSA, for eight sampling campaigns. The average removal efficiencies were in the range of 3.13-97.3% for wetlands in DBNSA. The highest average removal occurred in the east inlet to the outlet of the Tatan wetland. The most frequently detected compound was OP (57.7%), whose concentration was up to 1458.7 ng/L in DBNSA. NP was seen in only 20.5% of the samples. The temporal variation of EDs showed a decrease across seasons, where summer>spring>winter>autumn in these constructed wetlands. The removal efficiencies of EDs by estuarine wetlands, in decreasing order, were Datan>Pengcun>Linbian right bank in DBNSA. Water samples collected at 18 sites in three freshwater constructed wetlands (Daniaopi, Hsin-Hai I, and Hsin-Hai II) along the riparian area of Dahan River. NP2EO was the most abundant compound, with a concentration of up to 11,200 ng/L. Removal efficiencies ranged from 55% to 91% for NP1EO, NP2EO, and NP in Hsin-Hai I. The average removal potential of EDs in freshwater constructed wetlands, in decreasing order, was Hsin-Hai II>Daniaopi>Hsin-Hai I constructed wetlands. The lowest concentrations of the selected compounds were observed in the winter. The highest removal efficiency of the selected phenolic endocrine disruptors was achieved by Hsin-Hai I wetland. The calculated risk quotients used to evaluate the ecological risk were up to 30 times higher in the freshwater wetlands along Dahan River than in the estuarine (DBNSA) constructed wetlands, indicating that existing concentrations of these EDs in wetland systems pose a high ecological risk to aquatic organisms. The decreasing risk quotient from influent to effluent indicates that phenolic endocrine disruptors can be treated in these constructed wetlands. Our results of this research can serve as a preliminary understanding on the ED removal efficiencies in different types of constructed wetlands.

Contribution of primary and secondary treatment on the removal of benzothiazoles, benzotriazoles, endocrine disruptors, pharmaceuticals and perfluorinated compounds in a sewage treatment plant

The occurrence and fate of 36 emerging contaminants, belonging to five different classes, (benzotriazoles, BTRs; benzothiazoles, BTHs; perfluorinated compounds, PFCs; non-steroidal anti-inflammatory drugs, NSAIDs and endocrine disruptors, EDCs) were investigated in raw, treated wastewater (both particulate and dissolved phases), and in sludge from a sewage treatment plant (STP) in Athens, Greece. The average concentrations of BTRs, BTHs, NSAIDs and EDCs in raw wastewater ranged between 11 ng L(-1) and 7.27 μg L(-1), while PFCs did not exceed 100 ng L(-1). In dewatered sludge, the average concentrations ranged between 0.8 ng g(-1) dw (perfluorohexanoic acid, PFHxA) and 3895 ng g(-1) dw (nonylphenol, NP). The distribution of emerging contaminants between particulate and dissolved phase was different among the compounds. BTRs and BTHs showed lower solid-liquid distribution coefficients (Kd) than all other compounds. For 9 over the 27 compounds detected in influents, the removal efficiency was higher than 70%, while the others either were removed to a lesser extent or detected at higher concentrations in effluents. Based on this, advanced treatment processes should be applied in the future for achieving adequate emerging contaminants removal in STPs. Regarding removal mechanisms, almost 60% of BTRs and 30 to 75% of BTHs were removed in bioreactors, while the contribution of primary and secondary clarifiers was of minor importance. Sorption to primary sludge was a significant mechanism affecting EDCs fate in STP.

Impact of selected wastewater constituents on the removal of sulfonamide antibiotics via ultrafiltration and micellar enhanced ultrafiltration

To better understand the environmental mobility of sulfonamide antibiotics and develop improved processes for their removal during wastewater treatment, stirred cell ultrafiltration (UF) experiments were conducted using both synthetic and real wastewater effluent. The interactions between selected sulfonamides (sulfaguanidine, sulfathiazole and sulfamerazine), solids and dissolved organic matter were systematically explored. The further impact of micellar enhanced ultrafiltration (MEUF), a process in which surfactants are added at micellar concentrations to enhance removal of various trace contaminants from aqueous streams, was then explored by using a cationic surfactant, cetyltrimethylammonium bromide (CTAB). Ultrafiltration of sulfonamides in the absence of other materials generally removed only 15-20% of the antibiotics. The presence of micellar solutions of CTAB generally improved removal of sulfonamides over UF alone, with rejections ranging from 20 to 74%. Environmental solids (sediment) further increased retention of sulfonamides using both UF and MEUF, but the presence of DOM did not influence rejection. Similar trends were observed on UF and MEUF of real effluent samples that had been spiked with the sulfonamides, confirming the environmental relevance of the observed interactions between sulfonamides, surfactant, and wastewater constituents. The results demonstrate that MEUF processes can be designed for the selective removal of such trace contaminants as sulfonamide antibiotics.

Meta-analysis of environmental contamination by alkylphenols

Alkylphenols and alkylphenol ethoxylates (APE) are toxics classified as endocrine-disrupting compounds; they are used in detergents, paints, herbicides, pesticides, emulsifiers, wetting and dispersing agents, antistatic agents, demulsifiers, and solubilizers. Many studies have reported the occurrence of alkylphenols in different environmental matrices, though none of these studies have yet to establish a comprehensive overview of such compounds in the water cycle within an urban environment. This review summarizes APE concentrations for all environmental media throughout the water cycle, from the atmosphere to receiving waters. Once the occurrence of compounds has been assessed for each environmental compartment (urban wastewater, wastewater treatment plants [WWTP], atmosphere, and the natural environment), data are examined in order to understand the fate of APE in the environment and establish their geographical and historical trends. From this database, it is clear that the environment in Europe is much more contaminated by APE compared to North America and developing countries, although these APE levels have been decreasing in the last decade. APE concentrations in the WWTP effluent of developed countries have decreased by a factor of 100 over the past 30 years. This study is aimed at identifying both the correlations existing between environmental compartments and the processes that influence the fate and transport of these contaminants in the environment. In industrial countries, the concentrations observed in waterways now represent the background level of contamination, which provides evidence of a past diffuse pollution in these countries, whereas sediment analyses conducted in developing countries show an increase in APE content over the last several years. Finally, similar trends have been observed in samples drawn from Europe and North America.

Aerobic biotransformation of n-tetradecylbenzyldimethylammonium chloride by an enriched Pseudomonas spp. community

The biotransformation of n-tetradecylbenzyldimethylammonium chloride (C(14)BDMA-Cl), a quaternary ammonium compound (QAC), under aerobic conditions by an enriched microbial community growing on benzalkonium chlorides (BACs) was investigated. Biotransformation of C(14)BDMA-Cl commenced with cleavage of the C(alkyl)-N bond and formation of benzyldimethylamine (BDMA). BDMA was further degraded, but in contrast to a previously reported BAC biotransformation pathway, neither benzylmethylamine (BMA) nor benzylamine (BA) was detected as a BDMA biotransformation product. Kinetic assays further confirmed that BMA and BA were not intermediates of C(14)BDMA-Cl transformation by the enriched community. Thus, BDMA is thought to be transformed to dimethylamine and benzoic acid via debenzylation. The biomass-normalized rate of C(14)BDMA-Cl biotransformation was 0.09 μmol/[mg of volatile suspended solids (VSS)·h]. The Microtox acute toxicity EC(50) value of BDMA was 500 times higher than that of C(14)BDMA-Cl. Thus, the aerobic biotransformation of C(14)BDMA-Cl to BDMA results in substantial toxicity reduction. Phylogenetic analysis of Bacteria diversity indicated that the majority of the sequenced clones (98% of the clone library) belonged to the genus Pseudomonas.

Prioritising chemicals used in personal care products in China for environmental risk assessment: application of the RAIDAR model

China represents a significant market for the sale of personal care products (PCPs). Given the continuous emission of hundreds of chemicals used in PCPs to waste water and the aquatic environment after regular use, methods for prioritising the environmental risk assessment for China are needed. In an effort to assess the prioritisation of chemicals used in PCPs in China, we have identified the chemical ingredients used in 2500 PCPs released to the Chinese market in 2009, and estimated the annual emission of these chemicals. The physical-chemical property data for these substances have been estimated and used as model inputs in the RAIDAR model. In general, the RAIDAR model provides an overall assessment of the multimedia fate of chemicals, and provides a holistic approach for prioritising chemical ingredients. The prioritisation exercise conducted in this study is shown to be strongly influenced by loss processes, such as the removal efficiencies of WWT plants and biotransformation.

Identification of relevant micropollutants in Austrian municipal wastewater and their behaviour during wastewater treatment

The European Union has defined environmental quality standards (EQSs) for surface waters for priority substances and several other pollutants. Furthermore national EQSs for several chemicals are valid in Austria. The study investigated the occurrence of these compounds in municipal wastewater treatment plant (WWTP) effluents. In a first screening of 15 WWTPs relevant substances were identified, which subsequently were monitored in 9 WWTPs over 1 year (every 2 months). Out of 77 substances or groups of substances (including more than 90 substances) 13 were identified as potentially relevant in respect to water pollution and subjected to the monitoring, whereas most other compounds were detected in concentrations far below the respective EQS for surface waters and therefore not further considered. The preselected 13 compounds for monitoring were cadmium (Cd), nickel (Ni), copper (Cu), selenium (Se), zinc (Zn), diuron, polybrominated diphenyl ethers (PBDEs), di(ethyl-hydroxyl)phthalate (DEHP), tributyltin compounds (TBT), nonylphenoles (NP), adsorbable organic halogens (AOX) and the complexing agents ethylenediaminetetraacetic acid (EDTA) as well as nitrilotriacetic acid (NTA). In the effluents of WWTPs the concentrations of the priority substances Cd, NP, TBT and diuron frequently exceeded the respective EQS, whereas the concentrations for DEHP and Ni were below the respective EQS. The effluent concentrations for AOX, EDTA, NTA, Cu, Se and Zn frequently are in the range or above the Austrian EQS for surface waters. Besides diuron and EDTA all compounds are removed at least partially during wastewater treatment and for most substances the removal via the excess sludge is the major removal pathway. For the 13 compounds which were monitored in WWTP effluents population equivalent specific discharges were calculated. Since for many compounds no or only few information is available, these population equivalent specific discharges can be used to assess emissions from municipal WWTPs to surface waters as well as to make a first assessment of the impact of a discharge on surface waters chemical status. Comparing discharges and river pollution on a load basis, the influence of diffuse sources becomes obvious and therefore should also be taken into consideration in river management.

Emergence of resistance to antibacterial agents: the role of quaternary ammonium compounds--a critical review

Quaternary ammonium compounds (QACs) are widely distributed in hospitals, industry and cosmetics. Little attention has been focused on the potential impact of QACs on the emergence of antibiotic resistance in patients and the environment. To assess this issue, we conducted a literature review on QAC chemical structure, fields of application, mechanism of action, susceptibility testing, prevalence, and co- or cross-resistance to antibiotics. Special attention was paid to the effects of QACs on microflora; in particular, the issue of the potential of QACs for applying selective pressure on multiple-antibiotic-resistant organisms was raised. It was found that there is a lack of standardised procedures for interpreting susceptibility test results. QACs have different impacts on the minimum inhibitory concentrations of antibacterials depending on the antibacterial compound investigated, the resistance genes involved, the measuring methodology and the interpretative criteria. The unmet needs for adequate detection of reduced susceptibility to QACs and antibiotics include (i) a consensus definition for resistance, (ii) epidemiological cut-off values and (iii) clinical resistance breakpoints. This review advocates the design of international guidelines for QAC use.

Hospital wastewater treatment by membrane bioreactor: performance and efficiency for organic micropollutant elimination

A pilot-scale membrane bioreactor (MBR) was installed and operated for one year at a Swiss hospital. It was fed an influent directly from the hospital's sanitary collection system. To study the efficiency of micropollutant elimination in raw hospital wastewater that comprises a complex matrix with micropollutant concentrations ranging from low ng/L to low mg/L, an automated online SPE-HPLC-MS/MS analytical method was developed. Among the 68 target analytes were the following: 56 pharmaceuticals (antibiotics, antimycotics, antivirals, iodinated X-ray contrast media, antiinflamatory, cytostatics, diuretics, beta blockers, anesthetics, analgesics, antiepileptics, antidepressants, and others), 10 metabolites, and 2 corrosion inhibitors. The MBR influent contained the majority of those target analytes. The micropollutant elimination efficiency was assessed through continuous flow-proportional sampling of the MBR influent and continuous time-proportional sampling of the MBR effluent. An overall load elimination of all pharmaceuticals and metabolites in the MBR was 22%, as over 80% of the load was due to persistent iodinated contrast media. No inhibition by antibacterial agents or disinfectants from the hospital was observed in the MBR. The hospital wastewater was found to be a dynamic system in which conjugates of pharmaceuticals deconjugate and biological transformation products are formed, which in some cases are pharmaceuticals themselves.

Liquid phase micro-extraction of linear alkylbenzene sulfonate anionic surfactants in aqueous samples

Hollow fiber liquid phase micro-extraction (LPME) of linear alkylbenzene sulfonates (LAS) from aqueous samples was studied. Ion pair extraction of C₁₀, C₁₁, C₁₂ and C₁₃ homologues was facilitated with trihexylamine as ion-pairing agent, using di-n-hexylether as solvent for the supported liquid membrane (SLM). Effects of extraction time, acceptor buffer concentration, stirring speed, sample volume, NaCl and humic acids were studied. At 10–50 μg L⁻¹ linear R²-coefficients were 0.99 for C₁₀ and C₁₁ and 0.96 for C₁₂. RSD was typically ∼15%. Three observations were especially made. Firstly, LPME for these analytes was unusually slow with maximum enrichment observed after 15–24 h (depending on sample volume). Secondly, the enrichment depended on LAS sample concentration with 35–150 times enrichment below ∼150 μg L⁻¹ and 1850–4400 times enrichment at 1 mg L⁻¹. Thirdly, lower homologues were enriched more than higher homologues at low sample concentrations, with reversed conditions at higher concentrations. These observations may be due to the fact that LAS and the amine counter ion themselves influence the mass transfer at the water-SLM interface. The observations on LPME of LAS may aid in LPME application to other compounds with surfactant properties or in surfactant enhanced membrane extraction of other compounds.

Physicochemistry of interaction between the cationic polymer poly(diallyldimethylammonium chloride) and the anionic surfactants sodium dodecyl sulfate, sodium dodecylbenzenesulfonate, and sodium N-dodecanoylsarcosinate in water and isopropyl alcohol-water media

The physicochemistry of interaction of the cationic polymer poly(diallyldimethylammonium chloride) (PDADMAC) with the anionic surfactants sodium dodecyl sulfate, sodium dodecylbenzenesulfonate, and sodium N-dodecanoylsarcosinate was studied in detail using tensiometry, turbidimetry, calorimetry, viscometry, dynamic light scattering (DLS), and scanning electron microscopy (SEM). Fair interaction initially formed induced small micelles of the surfactants and later on produced free normal micelles in solution. The interaction process yielded coacervates that initially grew by aggregation in the aqueous medium and disintegrated into smaller species at higher surfactant concentration. The phenomena observed were affected by the presence of isopropyl alcohol (IP) in the medium. The hydrodynamic sizes of the dispersed polymer and its surfactant-interacted species were determined by DLS measurements. The surface morphologies of the solvent-removed PDADMAC and its surfactant-interacted complexes from water and IP-water media were examined by the SEM technique. The morphologies witnessed different patterns depending on the composition and the solvent environment. The head groups of the dodecyl chain containing surfactants made differences in the interaction process.

Effect of biological and chemical oxidation on the removal of estrogenic compounds (NP and BPA) from wastewater: an integrated assessment procedure

A major source of the wide presence of EDCs (Endocrine Disrupting Compounds) in water bodies is represented by direct/indirect discharge of sewage. Recent scientific literature reports data about their trace concentration in water, sediments and aquatic organisms, as well as removal efficiencies of different wastewater treatment schemes. Despite the availability of a huge amount of data, some doubts still persist due to the difficulty in evaluating synergistic effects of trace pollutants in complex matrices. In this paper, an integrated assessment procedure was used, based on chemical and biological analyses, in order to compare the performance of two full scale biological wastewater treatment plants (either equipped with conventional settling tanks or with an ultrafiltration membrane unit) and tertiary ozonation (pilot scale). Nonylphenol and bisphenol A were chosen as model EDCs, together with the parent compounds mono- and di-ethoxylated nonylphenol (quantified by means of GC-MS). Water estrogenic activity was evaluated by applying the human breast cancer MCF-7 based reporter gene assay. Process parameters (e.g., sludge age, temperature) and conventional pollutants (e.g., COD, suspended solids) were also measured during monitoring campaigns. Conventional activated sludge achieved satisfactory removal of both analytes and estrogenicity. A further reduction of biological activity was exerted by MBR (Membrane Biological Reactor) as well as ozonation; the latter contributed also to decrease EDC concentrations.

Evaluation and modeling of benzalkonium chloride inhibition and biodegradation in activated sludge

The inhibitory effect and biodegradation of benzalkonium chloride (BAC), a mixture of alkyl benzyl dimethyl ammonium chlorides with different alkyl chain lengths, was investigated at a concentration range from 5 to 20 mg/L and different biomass concentrations in an activated sludge system. A solution containing glucose and mineral salts was used as the wastewater in all the assays performed. The inhibition of respiratory enzymes was identified as the mode of action of BAC as a result of oxygen uptake rate analysis performed at BAC concentrations ranging between 5 and 70 mg/L. The glucose degradation in the activated sludge at different BAC and biomass concentrations was well-described with Monod kinetics with competitive inhibition. The half-saturation inhibition constant (K(I)) which is equivalent to EC(50) of BAC for the activated sludge tested ranged between 0.12 and 3.60 mg/L. The high K(I) values were recorded at low BAC-to-biomass ratios, i.e. less than 10 mg BAC/g VSS, at which BAC was almost totally adsorbed to biomass and not bioavailable. BAC degradation started as soon as glucose was totally consumed. Although BAC was almost totally adsorbed on the biomass, it was degraded completely. Therefore, BAC degradation was modeled using two-phase biodegradation kinetics developed in this study. This model involves rapid partitioning of BAC to biomass and consecutive degradation in both aqueous and solid phases. The aqueous phase BAC degradation rate was twenty times, on average, higher than the solid phase degradation rate. The specific aqueous (k(I1)) and solid (k(I2)) phase BAC utilization rate constants were 1.25 and 0.31 mg BAC/g VSS h, respectively. The findings of this study would help to understand the reason of extensive distribution of quaternary ammonium compounds in wastewater treatment plant effluents and in natural water systems although QACs are biodegradable, and develop strategies to avoid their release and accumulation in the environment.

Review of 'emerging' organic contaminants in biosolids and assessment of international research priorities for the agricultural use of biosolids

A broad spectrum of organic chemicals is essential to modern society. Once discharged from industrial, domestic and urban sources into the urban wastewater collection system they may transfer to the residual solids during wastewater treatment and assessment of their significance and implications for beneficial recycling of the treated sewage sludge biosolids is required. Research on organic contaminants (OCs) in biosolids has been undertaken for over thirty years and the increasing body of evidence demonstrates that the majority of compounds studied do not place human health at risk when biosolids are recycled to farmland. However, there are 143,000 chemicals registered in the European Union for industrial use and all could be potentially found in biosolids. Therefore, a literature review of 'emerging' OCs in biosolids has been conducted for a selection of chemicals of potential concern for land application based upon human toxicity, evidence of adverse effects on the environment and endocrine disruption. To identify monitoring and research priorities the selected chemicals were ranked using an assessment matrix approach. Compounds were evaluated based upon environmental persistence, human toxicity, evidence of bioaccumulation in humans and the environment, evidence of ecotoxicity and the number and quality of studies focussed on the contaminant internationally. The identified chemicals of concern were ranked in decreasing order of priority: perfluorinated chemicals (PFOS, PFOA); polychlorinated alkanes (PCAs), polychlorinated naphthalenes (PCNs); organotins (OTs), polybrominated diphenyl ethers (PBDEs), triclosan (TCS), triclocarban (TCC); benzothiazoles; antibiotics and pharmaceuticals; synthetic musks; bisphenol A, quaternary ammonium compounds (QACs), steroids; phthalate acid esters (PAEs) and polydimethylsiloxanes (PDMSs). A number of issues were identified and recommendations for the prioritisation of further research and monitoring of 'emerging' OCs for the agricultural use of biosolids are provided. In particular, a number of 'emerging' OCs (PFOS, PFOA and PCAs) were identified for priority attention that are environmentally persistent and potentially toxic with unique chemical properties, or are present in large concentrations in sludge, that make it theoretically possible for them to enter human and ecological food-chains from biosolids-amended soil.

The determination of the linear alkylbenzene sulfonate isomers in water samples by gas-chromatography/mass spectrometry

A number of 20 compounds of linear alkylbenzene sulfonates (LASs) family were identified by electron impact mass spectrometry (EI-MS) in water samples collected from wastewater treatment plants (WWTP). This paper presents the mass spectra of 20 compounds, the proposed mechanism of formation of the diagnostic ions obtained by EI-MS and the distribution of individual isomers in water samples collected from compartments of WWTP. The individual isomers from four homolog series C(10)-, C(11)-, C(12)- and C(13)-LAS were analyzed as methyl derivatives.

Fate of surfactants in membrane bioreactors and conventional activated sludge plants

Two membrane bioreactors (MBRs) were operated at high sludge retention time (SRT) (between 30 and 75 d) in parallel to a conventional activated sludge plant (CASP) conducted at SRT = 10 d. The fate of linear alkylbenzene sulfonate (LAS), nonylphenol ethoxylates (NP(n)EO, n = 1-15), nonylphenoxy carboxylates (NP(n)EC, n = 1-2), and nonylphenol (NP) in these systems was investigated. All systems were very efficient in the removal of LAS (around 99%). The analysis of variance showed that the difference in the removal efficiency of LAS in the CASP and the MBR operated at SRT = 65-75 d (respectively 99.0 ± 0.43 and 99.8 ± 0.11) were significant (p < 0.05), confirming the importance of SRT in the removal of LAS. Comparison between the CASP and the MBRs in the removal efficiency of nonylphenolic compounds were conducted considering NP(3-15)EO, the sum of NP(1-15)EO, NP(1-2)EC, and nonylphenol (NP). In all cases MBRs were more efficient than the CASP. In the case of NP the removal was about 76 ± 7.5% for the CASP and 90% ± 12.1 and 82 ± 8.7% for the MBRs. Better performance of MBRs in the removal of nonylphenolic compounds can be attributed to a better degradation. For example, if the sum of NP(1-15)EO and NP(1-2)EC is considered, estimated biodegradation was about 48% for the CASP and 72% for MBRs.

Assessing the fate of nitrosamine precursors in wastewater treatment by physicochemical fractionation

Source control or elimination of precursors of NDMA and other nitrosamines in wastewater requires information on their physicochemical properties, which is still limited. Thus we developed a multistep fractionation method based on a combination of consecutive filtration steps to <1 μm, <0.2 μm, and <2.5 kDa followed by solid-phase extraction on a C18 column and validated it using model NDMA precursors covering a wide polarity range. The membrane filtration to <2.5 kDa was suitable to separate a low-molecular weight precursor fraction but partially removed hydrophobic compounds by sorption. Fractionation on a C18 column allowed distinguishing highly polar precursors (such as dimethylamine) from less polar ones (such as ranitidine or other pharmaceuticals). Application of the fractionation procedure together with the formation potential test revealed that in the influent of one studied wastewater treatment plant about 50% of all precursors were associated with colloids or macromolecules, suggesting that these fractions comprise sorbed hydrophobic precursors. During activated sludge treatment small polar and charged NDMA and other nitrosamines' precursors were removed to about 80%. In contrast, less polar precursors were more recalcitrant. In advanced treatment steps, only small fractions of the precursors were removed by the prechlorination/ultrafiltration step, while reverse osmosis removed >98% of all precursors.

Occurrence of alkyltrimethylammonium compounds in urban estuarine sediments: behentrimonium as a new emerging contaminant

The distribution of alkyltrimethylammonium compounds (ATMAC), cationic surfactants used in a wide variety of applications, has been determined in sediments from Jamaica Bay (NY). Total concentrations in surficial sediments collected between 1998 and 2008 ranged from 361 to 6750 ng/g. The highest values were found in samples from a deeper basin directly affected by treated wastewater discharges. Behentrimonium, a mixture dominated by a homologue having 22 carbon atoms in its alkyl chain (ATMAC 22), was identified for the first time using time-of-flight mass spectrometry and accounted for approximately 80% of the total ATMAC in recent sediment samples. Analyses of a dated sediment core and subsequent surface grab samples revealed an exponential increase in concentration over the last three decades with a doubling time of 3.9 years. Similar temporal trends were seen in surface samples from other sites in Jamaica Bay and Newton Creek (NY), another site greatly influenced by wastewater discharges. This dramatic increase in ATMAC 22 reflects greater use of behentrimonium and likely replacement of other products containing other ATMAC homologues in personal care products. Further monitoring is recommended to assess the environmental risk and fate of this persistent emerging contaminant.

Determination of biocides and pesticides by on-line solid phase extraction coupled with mass spectrometry and their behaviour in wastewater and surface water

This study focused on the input of hydrophilic biocides into the aquatic environment and on the efficiency of their removal in conventional wastewater treatment by a mass flux analysis. A fully automated method consisting of on-line solid phase extraction coupled to LC-ESI-MS/MS was developed and validated for the simultaneous trace determination of different biocidal compounds (1,2-benzisothiazoline-3-one (BIT), 3-Iodo-2-propynylbutyl-carbamate (IPBC), irgarol 1051 and 2-N-octyl-4-isothiazolinone (octhilinone, OIT), carbendazim, diazinon, diuron, isoproturon, mecoprop, terbutryn and terbutylazine) and pharmaceuticals (diclofenac and sulfamethoxazole) in wastewater and surface water. In the tertiary effluent, the highest average concentrations were determined for mecoprop (1010 ng/L) which was at comparable levels as the pharmaceuticals diclofenac (690 ng/L) and sulfamethoxazole (140 ng/L) but 1-2 orders of magnitude higher than the other biocidal compounds. Average eliminations for all compounds were usually below 50%. During rain events, increased residual amounts of biocidal contaminants are discharged to receiving surface waters.

Quaternary ammonium compounds in urban estuarine sediment environments--a class of contaminants in need of increased attention?

The distributions of wastewater-derived quaternary ammonium compounds (QACs) were determined in surficial sediments (n = 47) collected from the urbanized lower Hudson River basin. The most abundant class of QACs were dialkyldimethylammonium compounds (DADMACs, with C8 to C18 carbon chain lengths; median ΣDADMAC = 26 μg/g), followed by benzylalkyldimethylammonium compounds (BAC, C12-C18; 1.5 μg/g), and alkyltrimethylammonium compounds (ATMAC, primarily C16 and C18; 0.52 μg/g). The concentrations of total QACs are higher than those of other conventional organic contaminants determined on the same samples (e.g., median ΣPAH level of 2.1 μg/g). Comparatively high concentrations, correlations with sewage derived contaminants, and the relatively constant compositions of QACs observed over large areas suggest that many sediment-sorbed QACs can be relatively persistent in receiving waters. Unusually large concentration-dependent sorption is considered as a mechanism that likely affects persistence of these intrinsically biodegradable chemicals under field conditions. There has been comparatively little field-based research on these classes of cationic surfactants; given the levels of QACs observed here, it is suggested that further investigation is warranted.

Surface water and wastewater treatment using a new tannin-based coagulant. Pilot plant trials

A new tannin-based coagulant-flocculant (Tanfloc) was tested for water treatment at a pilot plant level. Four types of water sample were treated: surface water (collected from a river), and municipal, textile industry (simulated by a 100 mg L(-1) aqueous solution of an acid dye), and laundry (simulated by a 50 mg L(-1) aqueous solution of an anionic surfactant) wastewaters. The pilot plant process consisted of coagulation, sedimentation, and filtration. The experiments were carried out with an average coagulant dosage of 92.2 mg L(-1) (except in the case of the surface water for which the dosage was 2 mg L(-1)). The efficacy of the water purification was notable in every case: total turbidity removal in the surface water and municipal wastewater, about 95% dye removal in the case of the textile industry wastewater, and about 80% surfactant removal in the laundry wastewater. Filtration improved the removal of suspended solids, both flocs and turbidity, and slightly improved the process as a whole. The efficiency of Tanfloc in these pilot studies was similar to or even better than that obtained in batch trials.

Does the wide use of quaternary ammonium compounds enhance the selection and spread of antimicrobial resistance and thus threaten our health?

Quaternary ammonium compounds (QACs) are widely used biocides that possess antimicrobial effect against a broad range of microorganisms. These compounds are used for numerous industrial purposes, water treatment, antifungal treatment in horticulture, as well as in pharmaceutical and everyday consumer products as preserving agents, foam boosters, and detergents. Resistance toward QACs is widespread among a diverse range of microorganisms and is facilitated by several mechanisms such as modifications in the membrane composition, expression of stress response and repair systems, or expression of efflux pump genes. Development of resistance in both pathogenic and nonpathogenic bacteria has been related to application in human medicine and the food industry. QACs in cosmetic products will inevitably come into intimate contact with the skin or mucosal linings in the mouth and thus are likely to add to the selection pressure toward more QAC-resistant microorganisms among the skin or mouth flora. There is increasing evidence of coresistance and cross-resistance between QACs and a range of other clinically important antibiotics and disinfectants. Use of QACs may have driven the fixation and spread of certain resistance cassette collectors (class 1 integrons), currently responsible for a major part of antimicrobial resistance in gram-negative bacteria. More indiscriminate use of QACs such as in cosmetic products may drive the selection of further new genetic elements that will aid in the persistence and spread of antimicrobial resistance and thus in limiting our treatment options for microbial infections.

Investigating the distribution of polybrominated diphenyl ethers through an Australian wastewater treatment plant

The aim of this study was to quantify the amount of polybrominated diphenyl ethers (PBDEs) released into the environment (biosolids, effluent) from a conventional Australian activated sludge treatment wastewater treatment plant (WWTP). The concentration of PBDE congeners was measured at various treatment stages and included four aqueous samples (raw, primary, secondary and tertiary effluents) and three sludges (primary, secondary and lime stabilized biosolids), collected at three sampling events over the course of the experiment (29 days). Semi-permeable membrane devices (SPMDs) were also installed for the duration of the experiment, the first time that SPMDs have been used to measure PBDEs in a WWTP. Over 99% of the PBDEs entering the WWTP were removed through the treatment processes, principally by sedimentation. The main congeners detected were BDE 47, 99 and 209, which are characteristic of the two major commercial formulations viz penta-BDE and deca-BDE. All the PBDE congeners measured were highly correlated with each other, suggesting a similar origin. In this case, the PBDEs are thought to be from domestic sources since domestic wastewater is the main contribution to the in-flow (approximately 95%). The mean concentration of SigmaPBDEs in chemically stabilized sewage sludge (biosolids) was 300microg kg(-1) dry weight. It is calculated that 2.3+/-0.3kg of PBDEs are disposed of each year with biosolids generated from the WWTP. If all Australian sewage sludge is contaminated to at least this concentration then at least 110kg of PBDEs are associated with Australian sewage sludge annually. Less than 10g are released annually into the environment via ocean outfall and field irrigation; this level of contamination is unlikely to pose risk to humans or the environment. The environmental release of treated effluent and biosolids is not considered a large source of PBDE environmental emissions compared to the quantities used annually in Australia.

Quaternary amines as nitrosamine precursors: a role for consumer products?

Nitrosamine formation has been associated with wastewater-impacted waters, but specific precursors within wastewater effluents have not been identified. Experiments indicated that nitrosamines form in low yields from quaternary amines, and that the nitrosamines form from the quaternary amines themselves, not just lower order amine impurities. Polymeric and benzylated quaternary amines were more potent precursors than monomeric quaternary alkylamines. Pretreatment of quaternary amines with ozone or free chlorine, which deactivate lower order amine impurities, did not significantly reduce nitrosamine formation. The nitrosamine formation pathway is unclear but experiments indicated that transformation of quaternary amines to lower order amine precursors via Hofmann elimination was not involved. Experiments suggest that the pathway may involve quaternary amine degradation by amidogen or chloramino radicals formed from chloramines. Quaternary amines are significant constituents of consumer products, including shampoos, detergents, and fabric softeners. Although quaternary amines may be removed by sedimentation during wastewater treatment, their importance should be evaluated on a case-by-case basis. The high loadings from consumer products may enable the portion not removed to serve as precursors.

Comparison of general water quality of rivers in Indonesia and Japan

In Java and Kalimantan in Indonesia, river water plays important roles in human life; for example, for transportation, and economic activities of the inhabitants. However, industrial, agricultural and domestic water is discarded into rivers directly in many developing countries, including Indonesia, since drainage systems have not been completely constructed. In this study, to evaluate the water quality and to compare those levels of environmental contaminants in developing and developed countries, water quality and contents of endocrine disrupters were measured in a total of 64 water samples (Indonesia; 28 samples and Japan; 36 samples) from 53 sites. The results indicated that, rivers in both capital cities, Jakarta and Tokyo, were contaminated. Water in rivers in Indonesia was not so heavily polluted as in Japan. Pollution in the river water in Indonesia appeared to be caused by the lack of sewerage systems. In addition, the findings on endocrine disrupters indicated that the concentration of alkylphenol in water samples was large enough to affect living organisms.

Nonylphenol ethoxylates and their metabolites in sewage treatment plants and rivers of Tianjin, China

Nonylphenol polyethoxylates (NPnEO) and nonylphenol (NP) have provoked much environmental concern because of their weak estrogenic activities. We monitored NPnEO and their metabolites in rivers in Tianjin and in a sewage treatment plant of Tianjin monthly for 1 year. The total concentrations of NPnEO and NP in influent, up to 47.2 microgL(-1) in August, were higher in summer than in other seasons. During the 12 months survey, NP was accumulated in most effluent samples with a mean value of 2.92 microgL(-1). The average concentrations of nonylphenol monoethoxylate (NP1EO), nonylphenol diethoxylate (NP2EO) and nonylphenol triethoxylate (NP3EO) in effluents were 1.26, 1.53 and 1.06 microgL(-1), which corresponds to percent removals of 75%, 60% and 62%, respectively. In rivers of Tianjin, NP2EO and nonylphenoxyethoxy acetic acid (NP2EC) exhibited the highest concentrations in the surface water, up to 1.38 and 9.59 microgL(-1), respectively. The pollution of nonylphenolic substances in sediments of Haihe River belongs to moderate or severe level in the world, with the total concentration between 4.1 and 9.9 microgg(-1), dry weight.

Transformation of benzalkonium chloride under nitrate reducing conditions

The effect and transformation potential of benzalkonium chlorides (BAC) under nitrate reducing conditions were investigated at concentrations up to 100 mg/L in batch assays using a mixed, mesophilic (35 degrees C) methanogenic culture. Glucose was used as the carbon and energy source and the initial nitrate concentration was 70 mg N/L Dissimilatory nitrate reduction to ammonia (DNRA) and to dinitrogen (DNRN) were observed at BAC concentrations up to 25 mg/L At and above 50 mg BAC/L, DNRA was inhibited and DNRN was incomplete resulting in accumulation of nitrous oxide. Long-term inhibition of methanogenesis and accumulation of volatile fatty acids were observed at and above 50 mg BAC/L Over 99% of the added BAC was recovered from all cultures except the one amended with 100 mg BAC/L where 37% of the initially added BAC was transformed during the 100 day incubation period. Abiotic and biotic assays performed with 100 mg/L of BAC and 5 mM (in the liquid phase) of either nitrate, nitrite, or nitric oxide demonstrated that BAC transformation was abiotic and followed the modified Hofmann degradation pathway, i.e., bimolecular nucleophilic substitution with nitrite. Alkyl dimethyl amines (tertiary amines) were produced at equamolar levels to BAC transformed, but were not further degraded. This is the first report demonstrating the transformation of BAC under nitrate reducing conditions and elucidating the BAC transformation pathway.

The influence of a surfactant, linear alkylbenzene sulfonate, on the estrogenic response to a mixture of (xeno)estrogens in vitro and in vivo

The effect of the presence of a surfactant on the activity of a mixture of environmental estrogens was assessed. In their natural habitat, fish are subject not only to exposure to mixtures of estrogenic compounds, as has been addressed in previous publications, but also to other confounding factors (chemical, physical and biological), which may, in theory, affect their responses to such compounds. To assess the potential for such interference, the commonly occurring surfactant, linear alkylbenzene sulfonate (LAS), was applied to the yeast estrogen screen at various concentrations, independently and together with a mixture of estrogens at constant concentrations. LAS enhanced the estrogenic activity of the mixture, an effect which became less pronounced over the course of time. This information was used to design an in vivo study to assess induction of vitellogenin in fathead minnows exposed to the same mixture of estrogens plus LAS. A similar trend was observed, that is, the response was enhanced, but the effect became less pronounced as the study progressed. However, the enhanced response in vivo occurred only at the highest concentration of LAS tested (362microg/L), and was transient because it was no longer apparent by the end of the study. Although LAS is a significant contaminant in terms of both concentration and frequency of detection in the aquatic environment, these data do not suggest that it will have a significant impact on the response of fish to environmental estrogens.

Oxidation of octylphenol by ferrate(VI)

The rates of the oxidation of octylphenols (OP) by potassium ferrate(VI) (K(2)FeO(4)) in water were determined as a function of pH (8.0-10.9) at 25 degrees C. The rate law for the oxidation of OP by Fe(VI) was found to be first order with each reactant. The observed second-order rate constants, k(obs), for the oxidation of alkylphenols decreased with an increase in pH. The speciation of Fe(VI) (HFeO(4)(-) and FeO(4)(2 -)) and OP (OP-OH and OP-O(-)) species were used to determine individual rate constants of the reactions. Comparison of rate constants and half-lives of oxidation of OP by Fe(VI) with nonylphenol (NP) and bisphenol-A (BPA) were conducted to demonstrate that Fe(VI) efficiently oxidizes environmentally relevant alkylphenols in water.

Endocrine disrupting compounds in municipal and industrial wastewater treatment plants in Northern Greece

The occurrence and fate of endocrine disrupting compounds (EDCs) in a sewage treatment plant and two industrial wastewater treatment plants from textile and tannery factories were investigated. EDCs of interest are 4-nonylphenol, 4-octylphenol, their ethoxylate oligomers (mono- and di-ethoxylates of nonylphenol and octylphenol), bisphenol A, triclosan and steroid estrogens. Target compounds were determined in dissolved fraction, total suspended solids and sludge by employing solid phase extraction and ultrasonication followed by gas chromatography-mass spectrometry. Nonylphenols and oligomers with one or two ethoxy groups were the most abundant compounds in raw wastewater as well as in effluents from all the treatment stages of sewage treatment plant, followed by triclosan and bisphenol A. Steroids were found at very low concentrations. Almost all phenolic EDCs compounds were predominantly associated to suspended solids in influents whereas the dissolved fraction dominated the treated effluents. High removal rates, ranging from 86% to 99%, were observed throughout the whole treatment process. Biodegradation was the main removal pathway of EDCs. Tannery wastewaters exhibited high concentrations of nonylphenolic compounds. This type of wastewaters could pose a significant risk to the aquatic and terrestrial environment.