Solution Combustion Synthesis of Nanoscale Materials

Sunlight-Driven Combustion Synthesis of Defective Metal Oxide Nanostructures with Enhanced Photocatalytic Activity

Synthesis of metal oxide nanostructures through combustion routes is a promising technique owing to its simplicity, rapidity, scalability, and cost-effectiveness. Herein, a sunlight-driven combustion approach is developed to synthesize pristine metal oxides and their heterostructures. Sunlight, a sustainable energy source, is used not only to initiate the combustion reaction but also to create oxygen vacancies on the metal oxide surface. ZnO nanostructures are successfully synthesized using this novel approach, and the products exhibit higher photocatalytic activity in the decomposition of methyl orange (MO) than ZnO nanostructures synthesized by the conventional methods. The higher photocatalytic activity is due to the narrower band gap, higher porosity, smaller and more uniform particle size, surface oxygen vacancies, as well as the enhanced exciton dissociation efficiency induced by the sunlight. Porous Fe₃O₄ nanostructures are also prepared using this environmentally benign method. Surprisingly, few-layer Bi₂O₃ nanosheets are successfully obtained using the sunlight-driven combustion approach. Moreover, the approach developed here is used to synthesize Bi₂O₃/ZnO heterostructure exhibiting a structure of few-layer Bi₂O₃ nanosheets decorated with ZnO nanoparticles. Bi₂O₃ nanosheets and Bi₂O₃/ZnO heterostructures synthesized by sunlight-driven combustion route exhibit higher photocatalytic activity than their counterparts synthesized by the conventional solution combustion method. This work illuminates a potential cost-effective method to synthesize defective metal oxide nanostructures at scale.

Effects of Precursor Concentration in Solvent and Nanomaterials Room Temperature Aging on the Growth Morphology and Surface Characteristics of Ni–NiO Nanocatalysts Produced by Dendrites Combustion during SCS

The morphology and surface characteristics of SCS(Solution Combustion Synthesis)-derived Ni–NiO nanocatalysts were studied. The ΤΕΜ results highlighted that the nanomaterial’s microstructure was modified by changing the reactants’ concentrations. The dendrites’ growth conditions were the main factors responsible for the observed changes in the nanomaterials’ crystallite size. Infrared camera measurements demonstrated a new type of combustion through dendrites. The XPS analysis revealed that the NiO structure resulted in the bridging of the oxygen structure that acted as an inhibitor of hydrogen adsorption on the catalytic surface and, consequently, the activity reduction. The RF-IGC indicated three different kinds of active sites with different energies of adsorption on the fresh catalyst and only one type on the aged catalyst. Aging of the nanomaterial was associated with changes in the microstructure of its surface by a gradual change in the chemical composition of the active centers.

Strength and aging resistance of monolithic zirconia: an update to current knowledge

New zirconia compositions with optimized esthetic properties have emerged due to the fast-growing technology in zirconia manufacturing. However, the large variety of commercial products and synthesis routes, make impossible to include all of them under the general term of “monolithic zirconia ceramics”. Ultra- or high translucent monolithic formulations contain 3–8 mol% yttria, which results in materials with completely different structure, optical and mechanical properties. The purpose of this study was to provide an update to the current knowledge concerning monolithic zirconia and to review factors related to strength and aging resistance. Factors such as composition, coloring procedures, sintering method and temperature, may affect both strength and aging resistance to a more or less extend. A significant reduction of mechanical properties has been correlated to high translucent zirconia formualtions while regarding aging resistance, the findings are contradictory, necessitating more and thorough investigation. Despite the obvious advantages of contemporary monolithic zirconia ceramics, further scientific evidence is required that will eventually lead to the appropriate laboratory and clinical guidelines for their use. Until then, a safe suggestion should be to utilize high-strength partially-stabilized zirconia for posterior or long span restorations and fully-stabilized ultra-translucent zirconia for anterior single crowns and short span fixed partial dentures.

Influence of Various Parameters on the SCS Ni/NiO Nanostructures and their Mechanism of Formation

Solution combustion synthesis (SCS) is an efficient approach to deliver materials with desirable properties directly in the nanoscale. Nevertheless, it is a very sensitive method and there are many parameters that influence the final materials’ properties and microstructure. In this work, four parameters that severely affect the combustion mechanism of formation for the final products, and as a result their final properties, are studied. These are the concentration of nitrates, the concentration of fuel in direct and slow heating and the time in furnace after the SCS is completed. It has been concluded that all these parameters affect the SCS process in a complicated way and an attempt has been made to explain the underlying mechanisms and processes that shape the final nanostructures. Finally, some of the as-synthesized Ni/NiO nanopowders were employed as catalysts and their activity was tested in the liquid-phase hydrogenation of maleic acid.

Cobalt and Nickel Phosphates as Multifunctional Air-Cathodes for Rechargeable Hybrid Sodium-Air Battery Applications

Noble-metal-free bifunctional electrocatalysts are indispensable to realize low-cost and energy-efficient rechargeable metal-air batteries. In addition, power density, energy density, and cycle life of these metal-air batteries can be improved further by utilizing the fast faradaic reactions of metal ions in the catalyst layer together with the oxygen evolution/reduction reactions (OER/ORR) for charge storage. In this work, we propose mixed metal phosphates of nickel and cobalt, Ni_xCo_3-x(PO₄)₂ (x = 0,1, 1.5, 2, and 3), as multifunctional air-cathodes exhibiting bifunctional electrocatalytic activity and reversible metal redox reaction (M^3+/2+, M = Ni and Co). Submicron-sized Ni_xCo_3-x(PO₄)₂ particles were synthesized by a solution combustion synthesis technique with urea acting as the fuel. Electrocatalytic activity toward the oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) in 0.1 M NaOH was systematically tuned by varying the Ni-to-Co ratio. The synthesized Ni_xCo_3-x(PO₄)₂ with x = 1.5 (NCP11) showed superior bifunctional catalytic activity to other samples. Moreover, the catalyst material delivered a specific capacity of ∼110 mAh g^-1 by the redox reactions of its metal sites. The hybrid Na-air battery fabricated using the NCP11 catalyst-loaded air-cathode exhibited low overpotential, stable cycling performance, and round-trip energy efficiency exceeding 78% in a 0.1 M NaOH aqueous electrolyte.

Perovskite synthesis, properties and their related biochemical and industrial application

The perovskite structure is shown to be the single most versatile ceramic host. Inorganic perovskite type oxides are attractive compounds for varied applications due to its large number of compounds, they exhibit both physical and biochemical characteristics and their Nano-formulation have been utilized as catalysts in many reaction due to their sensitivity, unique long-term stability and anti-interference ability. Some perovskites materials are very hopeful applicants for the improvement of effective anodic catalysts performance. Depending Perovskite-phase metal oxides distinct variety of properties they became useful for various applications they are newly used in electrochemical sensing of alcohols, glucose, hydrogen peroxide, gases, and neurotransmitters. Perovskite organometallic halide showed efficient essential properties for photovoltaic solar cells. This review presents a full coverage of the structure, progress of perovskites and their related applications. Stress is focused particularly to different methods of perovskites properties and there related application.

Additive Manufacturing of 3D-Architected Multifunctional Metal Oxides

Additive manufacturing (AM) of complex three-dimensional (3D) metal oxides at the micro- and nanoscales has attracted considerable attention in recent years. State-of-the-art techniques that use slurry-based or organic-inorganic photoresins are often hampered by challenges in resin preparation and synthesis, and/or by the limited resolution of patterned features. A facile process for fabricating 3D-architected metal oxides via the use of an aqueous metal-ion-containing photoresin is presented. The efficacy of this process, which is termed photopolymer complex synthesis, is demonstrated by creating nanoarchitected zinc oxide (ZnO) architectures with feature sizes of 250 nm, by first patterning a zinc-ion-containing aqueous photoresin using two-photon lithography and subsequently calcining them at 500 ºC. Transmission electron microscopy (TEM) analysis reveals their microstructure to be nanocrystalline ZnO with grain sizes of 5.1 ± 1.6 nm. In situ compression experiments conducted in a scanning electron microscope show an emergent electromechanical response: a 200 nm mechanical compression of an architected ZnO structure results in a voltage drop of 0.52 mV. This photopolymer complex synthesis provides a pathway to easily create arbitrarily shaped 3D metal oxides that could enable previously impossible devices and smart materials.

Efficient Fluoride Removal and Dye Degradation of Contaminated Water Using Fe/Al/Ti Oxide Nanocomposite

The trimetallic Fe/Al/Ti (1:1:1) nanocomposite (FAT), synthesized by an adaptable tuned chemical route, offers a new approach for water treatment, for example, the de-fluoridation and photodegradation soluble dye methylene blue (MB) at pH 7. FAT acted as a good fluoride scavenger in the presence of other co-ions and within a widespread pH range (pH 2-11). The photodegradation efficiencies were >90% for different concentrations of MB solutions. The characterization of FAT includes thermogravimetric analysis, X-ray diffraction, Fourier transform-infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, and ζ-potential analysis. Furthermore, the regeneration efficiencies of both the water treatments were checked, where the removal efficiency was not hampered significantly even after five batches. Spectroscopic techniques were adopted to perform the kinetic studies and to propose the probable mechanistic paths.

Oxygen Evolution Reaction of Co-Mn-O Electrocatalyst Prepared by Solution Combustion Synthesis

High-performance oxygen evolution reaction (OER) electrocatalysts are needed to produce hydrogen for energy generation through a carbon-free route. In this work, the solution combustion synthesis (SCS) method was employed to synthesize mixed phases of Co- and Mn-based oxides, and the relationships between the crystalline structure and the catalytic properties in the mixed phases were established. The mixed phases of Co- and Mn-based oxides shows promising OER properties, such as acceptable overpotential (450 mV for 10 mA∙cm−2) and Tafel slope (35.8 mV∙dec−1), highlighting the use of the mixed phases of Co- and Mn-based oxides as a new efficient catalysts for water splitting. Electronic structure of the mixed phases of Co- and Mn based oxides is studied in detail to give insight for the origin of high catalytic activities. In addition, excellent long-term stability for OER in alkaline media is achieved for the mixed phase of Co- and Mn based oxides.

Oxidatively induced exposure of active surface area during microwave assisted formation of Pt3Co nanoparticles for oxygen reduction reaction

The oxygen reduction reaction (ORR), the rate-limiting reaction in proton exchange membrane fuel cells, can efficiently be facilitated by properly manufactured platinum catalysts alloyed with late 3d transition metals. Herein we synthesize a platinum : cobalt nanoparticulate catalyst with a 3 : 1 atomic ratio by reduction of a dry metalorganic precursor blend within a commercial household microwave oven. The formed nanoparticles are simultaneously anchored to a carbon black support that enables large Pt surface area. Two separate microwave treatment steps were employed, where step one constitutes a fast oxidative treatment for revealing active surface area while a reductive secondary annealing treatment promotes a Pt rich surface. The resulting Pt₃Co/C catalyst (∼3.4 nm) demonstrates an enhanced ORR activity directly attributed to incorporated Co with a specific and mass activity of 704 μA cm_Pt⁻² and 352 A g_Pt⁻¹ corresponding to an increase by 279% and 66% respectively compared to a commercial Pt/C (∼1.8 nm) catalyst measured under identical conditions. The method's simplicity, scalability and novelty is expected to further assist in Pt–Co development and bring the catalyst one step closer toward commercialization and utility in fuel cells.

The oxygen reduction reaction (ORR) is efficiently facilitated platinum catalysts alloyed with Co and reveal high electrochemically active surface area via rapid microwave synthesis.

Bifunctional hexagonal Ni/NiO nanostructures: influence of the core-shell phase on magnetism, electrochemical sensing of serotonin, and catalytic reduction of 4-nitrophenol

Ni⁰/NiO (nickel/nickel oxide) core-shell nanostructures were synthesized through a facile combustible redox reaction. Remarkably, the hetero-phase boundary with different crystalline orientations offered dual properties, which helped in bifunctional catalysis. Presence of a metallic Ni phase changed physicochemical properties and some emerging applications (magnetic properties, optical conductivity, electrochemical sensitivity, catalytic behaviour) could be foreseen. Moreover, formation of a NiO layer on metal surface prevented magnetism-induced aggregation, arrested further oxidation by hindering oxygen diffusion, and acted as a good sorbent to enhance the surface adsorption of the analyte. Hexagonal Ni/NiO nanostructures manifested well-defined ferromagnetic behavior and the catalyst could be collected easily at the end of the catalytic reduction. Ni/NiO core-shell catalysts at the nanoscale had outstanding catalytic performance (reduction of 4-nitrophenol to 4-aminophenol) compared with pure NiO catalysts beyond a reaction time of ∼9 min. The estimated sensitivity, limit of detection and limit of quantification towards the electrochemical sensing of serotonin were 0.185, 0.43 and 1.47 μM μA^-1, respectively. These results suggest that a bifunctional Ni/NiO nanostructure could be a suitable catalyst for electrochemical detection of serotonin and reduction of 4-nitrophenol.

The Effect of the Precursor Solution’s Pretreatment on the Properties and Microstructure of the SCS Final Nanomaterials

Nanostructured nickel-based catalysts were produced by solution combustion synthesis and it was found that their properties and structure depended on the pretreatment of the precursor solution. X-ray diffraction, N2 adsorption, and an infrared high-speed camera were used to follow the various synthesis steps and to characterize the obtained catalysts, while their catalytic activity was determined in the hydrogenation of maleic acid. It was determined that the amount of water used and the heating of the precursor solution under mild stirring up to 70 °C influenced the nickel nitrate–glycine–water complexes that were formed in the precursor solution in the form of dendrites. These play a key role in the solution combustion synthesis (SCS) reaction mechanism and in particular in the formation of nickel-based catalysts. Understanding the interrelationships between the processing parameters and the ensuing powder properties allowed an efficient optimization of the catalytic performance.

Novel defect-fluorite pyrochlore sodium niobate nanoparticles: solution-phase synthesis and radiation tolerance analysis

Materials possessing a defect-fluorite pyrochlore structure can have a range of useful properties that are sought after, which include their radiation tolerance, nuclear waste immobilization, and phase stability at elevated temperatures. In this study, we demonstrate for the first time the synthesis and a detailed analysis of defect-fluorite pyrochlore sodium niobate (NaNbO3) nanoparticles. This analysis included an investigation into their stability to elevated temperatures and neutron irradiation. A surfactant-assisted solvothermal method is used to prepare nanoparticles of NaNbO3. This solution-phase approach results in the formation of crystalline nanoparticles of a defect-fluorite pyrochlore NaNbO3 at relatively low temperatures. The products had an average diameter of ∼74 ± 11 nm. The nanoparticles adopted a defect-fluorite pyrochlore phase and matched the cubic Fm3[combining macron]m space group. This pyrochlore form of NaNbO3 was found to be stable up to 500 °C. The nanoparticles transformed into the orthorhombic and rhombohedral perovskite phases of NaNbO3 along with the introduction of a pseudo-hexagonal Nb2O5 at higher temperatures. These defect-fluorite pyrochlore nanoparticles of NaNbO3 also exhibited a resistance to radiation induced amorphization. The dimensions, phase, and crystallinity of the defect-fluorite pyrochlore nanoparticles after exposure to a flux of neutrons were comparable to those of the as-synthesized product. The thermal stability and radiation tolerance of these pyrochlore nanoparticles could be useful in the design of thermally resilient materials, high temperature catalysts, and durable materials for the handling and storage of radioactive waste.

Binary Oxides Prepared by Microwave-Assisted Solution Combustion: Synthesis, Characterization and Catalytic Activity

Three different alumina-based Ni, Cu, Co oxide catalysts with metal loading of 10 wt %, and labeled 10Ni–Al, 10Co–Al and 10Cu–Al, were prepared by microwave-assisted solution combustion. Their morphological, structural and surface properties were deeply investigated by complementary physico-chemical techniques. Finally, the three materials were tested in CO oxidation used as test reaction for comparing their catalytic performance. The 10Cu–Al catalyst was constituted of copper oxide phase, while the 10Ni–Al and 10Co–Al catalysts showed the presence of “spinels” phases on the surface. The well-crystallized copper oxide phase in the 10Cu–Al catalyst, obtained by microwave synthesis, allowed for obtaining very high catalytic activity. With a CO conversion of 100% at 225 °C, the copper containing catalyst showed a much higher activity than that usually measured for catalytic materials of similar composition, thus representing a promising alternative for oxidation processes.

Combustion Synthesis of Non-Precious CuO-CeO₂ Nanocrystalline Catalysts with Enhanced Catalytic Activity for Methane Oxidation

In this study, xCuO-CeO₂ mixed oxide catalysts (Cu weight ratio x = 1.5, 3, 4.5, 6 and 15 wt.%) were prepared using solution combustion synthesis (SCS) and their catalytic activities towards the methane (CH₄) oxidation reaction were studied. The combustion synthesis of the pure CeO₂ and the CuO-CeO₂ solid solution catalysts was performed using copper and/or cerium nitrate salt as an oxidizer and citric acid as a fuel. A variety of standard techniques, including scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), thermo-gravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy were employed to reveal the microstructural, crystal, thermal and electronic properties that may affect the performance of CH₄ oxidation. The CuO subphase was detected in the prepared solid solution and confirmed with XRD and Raman spectroscopy, as indicated by the XRD peaks at diffraction angles of 35.3° and 38.5° and the Ag Raman mode at 289 cm-1, which are characteristics of tenorite CuO. A profound influence of Cu content was evident, not only affecting the structural and electronic properties of the catalysts, but also the performance of catalysts in the CH₄ oxidation. The presence of Cu in the CeO₂ lattice obviously promoted its catalytic activity for CH₄ catalytic oxidation. Among the prepared catalysts, the 6% CuO-CeO₂ catalyst demonstrated the highest performance, with T50 = 502 °C and T80 = 556 °C, an activity that is associated with the availability of a fine porous structure and the enhanced surface area of this catalyst. The results demonstrate that nanocrystalline copper-ceria mixed oxide catalysts could serve as an inexpensive and active material for CH₄ combustion.

A Facile Fabrication of Supported Ni/SiO2 Catalysts for Dry Reforming of Methane with Remarkably Enhanced Catalytic Performance

Ni catalysts supported on SiO2 are prepared via a facile combustion method. Both glycine fuel and ammonium nitrate combustion improver facilitate the formation of much smaller Ni nanoparticles, which give excellent activity and stability, as well as a syngas with a molar ratio of H2/CO of about 1:1 due to the minimal side reaction toward revserse water gas shift (RWGS) in CH4 dry reforming.

Synthesis of SiO2 nanostructures from Pennisetum glaucum and their effect on osteogenic differentiation for bone tissue engineering applications

Silica nanostructures were fabricated from Pennisetum glaucum (pearl millet) seed husk by acid-pretreatment and calcination. The fabricated silica nanostructure (SN) functional groups, crystalline nature, surface morphology, and particle size were analyzed by Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy, respectively. Additionally, the cytocompatibility of SNs was analyzed on human mesenchymal stem cells (hMSCs) in an MTT assay, propidium iodine (PI) staining, and acridine orange/ethidium bromide (AO/EB) staining. We observed peaks at 1090 and 800 cm^-1, which were assigned to symmetric, asymmetric, and bending vibrations of O-Si-O. The SNs showed an amorphous nature with a spherical shape and were 20-60 nm in diameter. The MTT assay results indicated that SNs exhibited cytocompatibility in hMSCs. The PI staining and AO/EB staining results suggested that SNs do not affect nuclear morphology at up to 400 μg/mL. Furthermore, SNs effect on osteogenic differentiation in hMSCs was studied. These results indicate that SNs induced osteogenic differentiation in hMSCs by upregulation of ALP, BSP, ON and RUNX2 genes. Our process could valorize the Pennisetum glaucum agricultural residues to high value products for bone tissue engineering applications.

Aqueous Solution Processing of Combustible Precursor Compounds into Amorphous Indium Gallium Zinc Oxide (IGZO) Semiconductors for Thin Film Transistor Applications

Combustion synthesis of semiconducting amorphous indium gallium zinc oxide IGZO (In:Ga:Zn, 7:1:1.5) thin films was carried out using urea nitrate precursor compounds of indium(III), gallium(III) and zinc(II). This approach provides further understanding towards the oxide formation process under a moderate temperature regime by employment of well-defined coordination compounds. All precursor compounds were fully characterized by spectroscopic techniques as well as by single crystal structure analysis. Their intrinsic thermal decomposition was studied by a combination of differential scanning calorimetry (DSC) and thermogravimetry coupled with mass spectrometry and infrared spectroscopy (TG-MS/IR). For all precursors a multistep decomposition involving a complex redox-reaction pathway under in situ formation of nitrogen containing molecular species was observed. Controlled thermal conversion of a mixture of the indium, gallium and zinc urea nitrate complexes into ternary amorphous IGZO films could thus be achieved. Thin film transistors (TFTs) were fabricated from a defined compositional mixture of the molecular precursors. The TFT devices exhibited decent charge carrier mobilities of 0.4 and 3.1 cm² /(Vs) after annealing of the deposited films at temperatures as low as 250 and 350 °C, respectively. This approach represents a significant step further towards a low temperature solution processing of semiconducting thin films.

Microwave-Assisted Catalytic Solvolysis of Lignin to Phenols: Kinetics and Product Characterization

Lignin, a major component of lignocellulosic biomass, is a valuable source of phenolic and aromatic compounds. It is, therefore, vital to develop strategies to selectively deconstruct lignin to valuable chemicals. This study focuses on the kinetics of depolymerization of lignin and the production of phenols via a microwave-assisted catalytic process at mild conditions of 80 °C in dimethyl sulfoxide/water medium. Four different catalysts used in this study, viz., Fe2O3, LaFeO3, ZrO2, and zeolite-Y hydrogen (ZYH), were characterized for structure, specific surface area, and surface morphology. The molecular weight reduction of lignin and the evolution of phenolic monomers and oligomers were monitored using various techniques, and the rate constants of lignin degradation in the presence of different catalysts were determined using a continuous distribution kinetics model, assuming scission of the lignin macromolecule at any random position. The rate constants (min-1) followed the trend: ZYH (26 × 10-4) ≈ LaFeO3 (25 × 10-4) > ZrO2 (22 × 10-4) > Fe2O3 ≈ no catalyst (16 × 10-4). Vanillic acid (15 mg g-1) and methyl phenol (17 mg g-1) were the major phenolics obtained with LaFeO3, whereas coniferaldehyde (13 mg g-1) was the major phenolic compound with Fe2O3. Vanillin was produced at ca. 11 mg g-1 with both Fe2O3 and ZYH. LaFeO3 is shown to be a promising catalyst for both molecular weight reduction of lignin and the production of monomeric phenols, whereas the use of Fe2O3 results in the formation of only phenols, possibly via specific end-chain depolymerization. The selectivities of the monomeric phenols were higher with these two catalysts, whereas with ZYH and ZrO2, the selectivities of the oligomers were better. The reusability of the catalysts and the effect of catalyst loading on kinetics of lignin depolymerization were also evaluated.

Structural, Magnetic, and Catalytic Evaluation of Spinel Co, Ni, and Co-Ni Ferrite Nanoparticles Fabricated by Low-Temperature Solution Combustion Process

Here, we present the low-temperature (∼600 °C) solution combustion method for the fabrication of CoFe₂O₄, NiFe₂O₄, and Co_0.5Ni_0.5Fe₂O₄ nanoparticles (NPs) of 12-64 nm range in pure cubic spinel structure, by adjusting the oxidant (nitrate ions)/reductant (glycine) ratio in the reaction mixture. Although nitrate ions/glycine (N/G) ratios of 3 and 6 were used for the synthesis, phase-pure NPs could be obtained only for the N/G ratio of 6. For the N/G ratio 3, certain amount of Ni²⁺ cations was reduced to metallic nickel. The NH₃ gas generated during the thermal decomposition of the amino acid (glycine, H₂NCH₂COOH) induced the reduction reaction. X-ray diffraction (XRD), Raman spectroscopy, vibrating sample magnetometry, and X-ray photoelectron spectroscopy techniques were utilized to characterize the synthesized materials. XRD analyses of the samples indicate that the Co_0.5Ni_0.5Fe₂O₄ NPs have lattice parameter larger than that of NiFe₂O₄, but smaller than that of CoFe₂O₄ NPs. Although the saturation magnetization (M _s) of Co_0.5Ni_0.5Fe₂O₄ NPs lies in between the saturation magnetization values of CoFe₂O₄ and NiFe₂O₄ NPs, high coercivity (H _c, 875 Oe) of the NPs indicate their hard ferromagnetic behavior. Catalytic behavior of the fabricated spinel NPs revealed that the samples containing metallic Ni are active catalysts for the degradation of 4-nitrophenol in aqueous medium.

Development of SrTiO3 Photocatalysts with Visible Light Response Using Amino Acids as Dopant Sources for the Degradation of Organic Pollutants in Aqueous Systems

N-doped and N,S-co-doped SrTiO3 photocatalysts were prepared using glycine and L-histidine amino acids as nitrogen sources and L-cysteine as nitrogen and sulphur source. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), N2 porosimetry, UV-Vis diffuse reflectance (DRS) and fluorescence spectroscopy, dynamic light scattering (DLS). Cubic SrTiO3 phase is formed in all samples, with crystal size ranged from 14.2 nm to 35.7 nm. The catalysts’ specific surface area and porosity depend on the amino acid dopant showing micro-mesoporosity for glycine, mesoporosity for histidine and non-porosity for cysteine. The lowest band gap (2.95 eV) was observed for the sample G-N-STO3 prepared with glycine (N:Sr:Ti 3:1:1 molar ratio) which produced also the higher amount of •OH radicals. The photocatalytic activity was tested against the degradation of methylene blue (MB) dye under UV-Vis and visible light irradiation following first-order kinetics.

Nanoscale self-assembly of thermoelectric materials: a review of chemistry-based approaches

This review is concerned with the leading methods of bottom-up material preparation for thermal-to-electrical energy interconversion. The advantages, capabilities, and challenges from a material synthesis perspective are surveyed and the methods are discussed with respect to their potential for improvement (or possibly deterioration) of application-relevant transport properties. Solution chemistry-based synthesis approaches are re-assessed from the perspective of thermoelectric applications based on reported procedures for nanowire, quantum dot, mesoporous, hydro/solvothermal, and microwave-assisted syntheses as these techniques can effectively be exploited for industrial mass production. In terms of energy conversion efficiency, the benefit of self-assembly can occur from three paths: suppressing thermal conductivity, increasing thermopower, and boosting electrical conductivity. An ideal thermoelectric material gains from all three improvements simultaneously. Most bottom-up materials have been shown to exhibit very low values of thermal conductivity compared to their top-down (solid-state) counterparts, although the main challenge lies in improving their poor electrical properties. Recent developments in the field discussed in this review reveal that the traditional view of bottom-up thermoelectrics as inferior materials suffering from poor performance is not appropriate. Thermopower enhancement due to size and energy filtering effects, electrical conductivity enhancement, and thermal conductivity reduction mechanisms inherent in bottom-up nanoscale self-assembly syntheses are indicative of the impact that these techniques will play in future thermoelectric applications.

Direct Z-Scheme Cs2O-Bi2O3-ZnO Heterostructures as Efficient Sunlight-Driven Photocatalysts

Limited light absorption, inefficient electron-hole separation, and unsuitable positions of conduction band bottom and/or valence band top are three major critical issues associated with high-efficiency photocatalytic water treatment. An attempt has been carried out here to address these issues through the synthesis of direct Z-scheme Cs₂O-Bi₂O₃-ZnO heterostructures via a facile, fast, and economic method: solution combustions synthesis. The photocatalytic performances are examined by the 4-chlorophenol degradation test under simulated sunlight irradiation. UV-vis diffuse reflectance spectroscopy analysis, electrochemical impedance test, and the observed transient photocurrent responses prove not only the significant role of Cs₂O in extending light absorption to visible and near-infrared regions but also its involvement in charge carrier separation. Radical-trapping experiments verify the direct Z-scheme approach followed by the charge carriers in heterostructured Cs₂O-Bi₂O₃-ZnO photocatalysts. The Z-scheme charge carrier pathway induced by the presence of Cs₂O has emerged as the reason behind the efficient charge carrier separation and high photocatalytic activity.

Synthesis of Highly Efficient Bifunctional Ag/Co3O4 Catalyst for Oxygen Reduction and Oxygen Evolution Reactions in Alkaline Medium

Ag/Co₃O₄ catalysts using three different modes of solution combustion synthesis were developed and characterized by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy to identify crystallite size, oxidation state, composition, and morphology. Cyclic voltammetry and linear sweep voltammetry measurements for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) confirm the bifunctionality of the electrocatalysts. The electrochemical evaluation indicates that a synergic effect between Ag and Co enhances the activity through the fast breaking of O-O bond in the molecular oxygen to enhance the reduction mechanism. The high content of cobalt (Co) in the catalyst Ag/Co₃O₄-12, synthesized by second wave combustion, improves the activity for ORR, and the reaction mechanism follows a 3.9 number of electron transfer in overall reaction. The kinetic and limiting current densities of Ag/Co₃O₄-12 are maximum when compared to those of other Ag/Co₃O₄ catalysts and are very close to commercial Pt/C. Moreover, the maximum current density of OER for Ag/Co₃O₄-12 makes it a promising candidate for various bifunctional electrocatalytic applications such as fuel cells and metal-air batteries.

Pt-Co and Pt-Ni Catalysts of Low Metal Content for H2 Production by Reforming of Oxygenated Hydrocarbons and Comparison with Reported Pt-Based Catalysts

New catalysts of Pt, PtNi, PtCo, and NiCo supported on Al2O3 were developed for producing hydrogen by aqueous phase reforming (APR) of oxygenated hydrocarbons. The urea matrix combustion technique was used for loading the metal on the support in order to improve several aspects: increase both the metal-support interaction and the metal dispersion and decrease the metal load. The catalysts were characterized by MS/ICP, N2 adsorption, XRD, TPR, CO chemisorption, and the test of cyclohexane dehydrogenation (CHD). The APR of a solution of 10% mass ethylene glycol (EG), performed in a tubular fixed bed reactor at 498 K, 22 bar, WHSV = 2.3 h−1, was used as the main reaction test. After 10 h on-stream, the catalysts prepared by UMC had better hydrogen yield and catalytic stability than common catalysts prepared by IWI. The UMC/IWI H2 yield ratio was 23.5/15.2 for Pt, 24.0/17.0 for PtCo, 26.6/21.0 for PtNi, and 8.0/3.9 for NiCo. Ni or Co addition to Pt increased the carbon conversion while keeping the H2 turnover high. Cobalt also improves stability. Reports of several authors were revised for a comparison. The analysis indicated that the developed catalysts are a viable and cheaper alternative for H2 production from a renewable resource.