Recent Advances in Wide-Bandgap Photovoltaic Polymers

A theoretical investigation for improving the performance of non-fullerene organic solar cells through side-chain engineering of BTR non-fused-ring electron acceptors

In the current quantum chemical study, indacenodithiophene donor core-based the end-capped alterations of the reference chromophore BTR drafted eight A2-A1-D-A1-A2 type small non-fullerene acceptors. All the computational simulations were executed under MPW1PW91/6-31G (d, p) level of DFT. The UV-Vis absorption, open circuit voltage, electron affinity, ionization potential, the density of states, reorganization energy, orbital analysis, and non-covalent interactions were studied and compared with BTR. Several molecules of our modeled series BT1-BT8 have shown distinctive features that are better than those of the BTR. The open circuit voltage (VOC) of BT5 has a favorable impact, allowing it to replace BTR in the field of organic solar cells. The charge carrier motilities for proposed molecules generated extraordinary findings when matched to the reference one (BTR). Further charge transmission was confirmed by creating the complex with a PM6 donor molecule. The remarkable dipole moment contributes to the formation of non-covalent bond interactions with chloroform, resulting in superior charge mobility. Based on these findings, it can be said that every tailored molecule has the potential to surpass chromophore molecule (BTR) in OSCs. So, all tailored molecules may enhance the efficiency of photovoltaic cells due to the involvement of potent terminal electron-capturing acceptor2 moieties. Considering these obtained results, these newly presented molecules can be regarded for developing efficient solar devices in the future.

Donor-acceptor-donor type AIEgens based on thieno[3.4-c]pyrrole-4,6-dione: Synthesis, electropolymerization, and electrochromism

Photoelectric functional materials with electrochemical reversible activity and fluorescence intensities have attracted significant interest due to their wide range of applications in optoelectronic devices. In this work, a series of photoresponsive and electroactive monomers based on thieno[3.4-c]pyrrole-4,6-dione (TPD) are synthesized and characterized. They possess planar geometry with smaller dihedral angles owing to the existence of a noncovalent conformation lock coming from the S atoms and the O atoms. Crystallographic, spectroscopic, and computational results reveal that the introduction of the TPD unit can endow the monomers with aggregation-induced emission (AIE), reduced energy levels, and increased electrochemical activity. The monomers were successfully polymerized through the electrochemical method, and the corresponding polymers displayed reversible electrochemical activity and stability. Moreover, polymer films based on 3,3-dimethyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine (ProE)-TPD have electrochromic properties in the near-infrared field with a high value of optical contrast ratio (∆T) of 27.1% at 1000 nm.

Nitrogen-Blowing Assisted Strategy for Fabricating Large-Area Organic Solar Modules with an Efficiency of 15.6

Organic solar cells (OSCs) are one of the most promising photovoltaic technologies due to their affordability and adaptability. However, upscaling is a critical issue that hinders the commercialization of OSCs. A significant challenge is the lack of cost-effective and facile techniques to modulate the morphology of the active layers. The slow solvent evaporation leads to an unfavorable phase separation, thus resulting in a low power conversion efficiency (PCE) of organic solar modules. Here, a nitrogen-blowing assisted method is developed to fabricate a large-area organic solar module (active area = 12 cm2) utilizing high-boiling-point solvents, achieving a PCE of 15.6%. The device fabricated with a high-boiling-point solvent produces a more uniform and smoother large-area film, and the assistance of nitrogen-blowing accelerates solvent evaporation, resulting in an optimized morphology with proper phase separation and finer aggregates. Moreover, the device fabricated by the nitrogen-blowing assisted method exhibits improved exciton dissociation, balanced carrier mobility, and reduced charge recombination. This work proposes a universal and cost-effective technique for the fabrication of high-efficiency organic solar modules.

Precisely Manipulating Molecular Packing via Tuning Alkyl Side-Chain Topology Enabling High-Performance Nonfused-Ring Electron Acceptors

In the development of high-performance organic solar cells (OSCs), the self-organization of organic semiconductors plays a crucial role. This study focuses on the precisely manipulation of molecular assemble via tuning alkyl side-chain topology in a series of low-cost nonfused-ring electron acceptors (NFREAs). Among the three NFREAs investigated, DPA-4, which possesses an asymmetric alkyl side-chain length, exhibits a tight packing in the crystal and high crystallinity in the film, contributing to improved electron mobility and favorable film morphology for DPA-4. As a result, the OSC device based on DPA-4 achieves an excellent power conversion efficiency of 16.67 %, ranking among the highest efficiencies for NFREA-based OSCs.

Phenothiazine-Based Donor-Acceptor Polymers as Multifunctional Materials for Charge Storage and Solar Energy Conversion

The increasing energy demand for diverse applications requires new types of devices and materials. Multifunctional materials that can fulfill different roles are of high interest as they can allow fabricating devices that can both convert and store energy. Herein, organic donor-acceptor redox polymers that can function as charge storage materials in batteries and as donor materials in bulk heterojunction (BHJ) photovoltaic devices are investigated. Based on its reversible redox chemistry, phenothiazine is used as the main building block in the conjugated copolymer design and combined with diketopyrrolopyrrol and benzothiadiazole as electron-poor comonomers to shift the optical absorption into the visible region. The resulting polymers show excellent cycling stability as positive electrode materials in lithium-organic batteries at discharge potentials of 3.6-3.7 V versus Li/Li+ as well as good performances in BHJ solar cells with up to 1.9% power conversion efficiency. This study shows that the design of such multifunctional materials is possible, however, that it also faces challenges, as essential properties for good device function can lead to diametrically opposite requirements in materials design.

A polymer library enables the rapid identification of a highly scalable and efficient donor material for organic solar cells

The dramatic improvement of the PCE (power conversion efficiency) of organic photovoltaic devices in the past few years has been driven by the development of new polymer donor materials and non-fullerene acceptors (NFAs). In the design of such materials synthetic scalability is often not considered, and hence complicated synthetic protocols are typical for high-performing materials. Here we report an approach to readily introduce a variety of solubilizing groups into a benzo[c][1,2,5]thiadiazole acceptor comonomer. This allowed for the ready preparation of a library of eleven donor polymers of varying side chains and comonomers, which facilitated a rapid screening of properties and photovoltaic device performance. Donor FO6-T emerged as the optimal material, exhibiting good solubility in chlorinated and non-chlorinated solvents and achieving 15.4% PCE with L8BO as the acceptor (15.2% with Y6) and good device stability. FO6-T was readily prepared on the gram scale, and synthetic complexity (SC) analysis highlighted FO6-T as an attractive donor polymer for potential large scale applications.

Organic Solar Cell With Efficiency Over 20% and VOC Exceeding 2.1 V Enabled by Tandem With All-Inorganic Perovskite and Thermal Annealing-Free Process

Organic solar cells (OSCs) based on polymer donor and non-fullerene acceptor achieve power conversion efficiency (PCE) more than 19% but their poor absorption below 550 nm restricts the harvesting of high-energy photons. In contrast, wide bandgap all-inorganic perovskites limit the absorption of low-energy photons and cause serious below bandgap loss. Therefore, a 2-terminal (2T) monolithic perovskite/organic tandem solar cell (TSC) incorporating wide bandgap CsPbI2 Br is demonstrated as front cell absorber and organic PM6:Y6 blend as rear cell absorber, to extend the absorption of OSCs into high-energy photon region. The perovskite sub-cell, featuring a sol-gel prepared ZnO/SnO2 bilayer electron transporting layer, renders a high open-circuit voltage (VOC ). The VOC is further enhanced by employing thermal annealing (TA)-free process in the fabrication of rear sub-cell, demonstrating a record high VOC of 2.116 V. The TA-free Ag/PFN-Br interface in organic sub-cell facilitates charge transport and restrains nonradiative recombination. Consequently, a remarkable PCE of 20.6% is achieved in monolithic 2T-TSCs configuration, which is higher than that of both reported single junction and tandem OSCs, demonstrating that tandem with wide bandgap all-inorganic perovskite is a promising strategy to improve the efficiency of OSCs.

Photoinduced Polaron Formation in a Polymerized Electron-Acceptor Semiconductor

Polymerized small molecular acceptor (PSMA) based all-polymer solar cells (all-PSC) have achieved power conversion efficiencies (PCE) over 16%, and the PSMA is considered to hold great promise for further improving the performance of all-PSC. Yet, in comparison with that of the polymer donor, the photophysics of a polymerized acceptor remains poorly understood. Herein, the excited state dynamics in a polymerized acceptor PZT810 was comprehensively investigated under various pump intensities and photon energies. The excess excitation energy was found to play a key role in excitons dissociation into free polarons for neat PSMA films, while free polarons cannot be generated from the polaron pairs in neat acceptor films. This work reveals an in-depth understanding of relaxation dynamics for PSMAs and that the underlying photophysical origin of PSMA can be mediated by excitation energies and intensities. These results would benefit the realization of the working mechanism for all-PSC and the designing of new PSMAs.

Photophysical Properties of BODIPY Derivatives for the Implementation of Organic Solar Cells: A Computational Approach

Solar cells based on organic compounds are a proven emergent alternative to conventional electrical energy generation. Here, we provide a computational study of power conversion efficiency optimization of boron dipyrromethene (BODIPY) derivatives by means of their associated open-circuit voltage, short-circuit density, and fill factor. In doing so, we compute for the derivatives' geometrical structures, energy levels of frontier molecular orbitals, absorption spectra, light collection efficiencies, and exciton binding energies via density functional theory (DFT) and time-dependent (TD)-DFT calculations. We fully characterize four D-π-A (BODIPY) molecular systems of high efficiency and improved J _sc that are well suited for integration into bulk heterojunction (BHJ) organic solar cells as electron-donor materials in the active layer. Our results are twofold: we found that molecular complexes with a structural isoxazoline ring exhibit a higher power conversion efficiency (PCE), a useful result for improving the BHJ current, and, on the other hand, by considering the molecular systems as electron-acceptor materials, with P3HT as the electron donor in the active layer, we found a high PCE compound favorability with a pyrrolidine ring in its structure, in contrast to the molecular systems built with an isoxazoline ring. The theoretical characterization of the electronic properties of the BODIPY derivatives provided here, computed with a combination of ab initio methods and quantum models, can be readily applied to other sets of molecular complexes to hierarchize optimal power conversion efficiency.

An electro-spun tri-component polymer biomaterial with optoelectronic properties for neuronal differentiation

Optoelectronic biomaterials have recently emerged as a potential treatment option for neurodegenerative diseases, such as optic macular degeneration. Though initial works in the field have involved bulk heterojunctions mimicking solar panels with photovoltaics (PVs) and conductive polymers (CPs), recent developments have considered abandoning CPs in such systems. Here, we developed a simple antioxidant, biocompatible, and fibrous membrane heterojunction composed of photoactive polymer poly(3-hexylthiophene) (P3HT), polycaprolactone (PCL) and polypyrrole (PPY), to facilitate neurogenesis of PC-12 cells when photo-stimulated in vitro. The photoactive prototype, referred to as PCL-P3HT/PPY, was fabricated via polymerization of pyrrole on electro-spun PCL-P3HT nanofibers to form a membrane. Four experimental groups, namely PCL alone, PCL/PPY, PCL-P3HT and PCL-P3HT/PPY, were tested. In the absence of the CP, PCL-P3HT demonstrated lower cell survival due to increased intracellular reactive oxygen/nitrogen species production. PCL-P3HT/PPY rescued these cells by virtue of scavenging radicals, where the CP, PPY, acted as an antioxidant. Apart from having lower impedance, the material also enhanced neurogenesis of PC-12 cells when photo-stimulated, compared to the traditional PCL-P3HT. Lastly, the in vitro system with PC-12 was used to demonstrate the practicality of the material for potential use as a cellular patch in optic and nerve regeneration. This work demonstrated the importance of maintaining PV-CP heterojunctions while simultaneously providing an optoelectrical platform for neural and optical tissue engineering. STATEMENT OF SIGNIFICANCE: Regeneration and repair of injured nervous systems have always been a major clinical challenge. Stem cell therapy is a promising approach for nerve regeneration, and opto-electrical stimulation, which converts light into an electrical signal, has been shown to efficiently regulate stem cell behaviors with enhanced neurogenesis. We developed a micro-fibrous membrane, composed of photoactive polymer, P3HT, scaffold material PCL and conductive polymer PPY. Our heterojunction system improved cell survival via PPY quenching PCL-P3HT-generated cell-damaging reactive oxygen species. PPY also conducted electrons produced from light-stimulated P3HT to promote neurogenesis. This photoactive microfiber biomaterial has great potential as a highly biocompatible and efficient platform to wirelessly promote neurogenesis and survival. Our approach thus showed possibilities with respect to optical tissue engineering.

Synthesis of Conjugated Donor-Acceptor Antiaromatic Porphyrins and Their Application to Perovskite Solar Cells

A conjugated donor-acceptor antiaromatic porphyrin, composed of an antiaromatic thieno-fused porphyrin structure and a diketopyrrolopyrrole mioety, was synthesized and applied in a perovskite solar cell for the first time. Enhanced light absorption in the device by the antiaromatic porphyrin resulted in a significantly increased power conversion efficiency of 19.3%.

Revealing the Side-Chain-Dependent Ordering Transition of Highly Crystalline Double-Cable Conjugated Polymers

We developed a series of highly crystalline double-cable conjugated polymers for application in single-component organic solar cells (SCOSCs). These polymers contain conjugated backbones as electron donor and pendant perylene bisimide units (PBIs) as electron acceptor. PBIs are connected to the backbone via alkyl units varying from hexyl (C₆ H₁₂ ) to eicosyl (C₂₀ H₄₀ ) as flexible linkers. For double-cable polymers with short linkers, the PBIs tend to stack in a head-to-head fashion, resulting in large d-spacings (e.g. 64 Å for the polymer P12 with C₁₂ H₂₄ linker) along the lamellar stacking direction. When the length of the linker groups is longer than a certain length, the PBIs instead adopt a more ordered packing likely via H-aggregation, resulting in short d-spacings (e.g. 50 Å for the polymer P16 with C₁₆ H₃₂ linker). This work highlights the importance of linker length on the molecular packing of the acceptor units and the influences on the photovoltaic performance of SCOSCs.

Binary and Ternary Polymer Solar Cells Based on a Wide Bandgap D-A Copolymer Donor and Two Nonfullerene Acceptors with Complementary Absorption Spectral

A new wide-bandgap conjugated D-A polymer denoted as P106 with a medium acceptor dithieno [2,3-e;3'2'-g]isoindole-7,9 (8H) (DTID) unit and strong 2-dodecylbenzo[1,2-b:3,4-b':6,5-b"]trithiophene (3TB) donor units shows an optical bandgap of 2.04 and highest occupied molecular orbital energy level of -5.56 eV. P106 is used as the donor and two nonfullerene acceptors-medium bandgap DBTBT-IC and narrow band Y18-DMO-are used as acceptors for the construction of binary and ternary bulk heterojunction polymer solar cells. The optimized polymer solar cells based on P106 : DBTBT-IC and P106 : Y18-DMO exhibit power conversion efficiencies of 11.76 % and 14.07 %, respectively. The short-circuit current density (22.78 mA cm^-2 ) for the P106 : Y18-DMO device is higher than that for P106 : DBTBT-IC (18.56 mA cm^-2 ) one, which could be attributed to the more photon harvesting efficiency of the P106 : Y18-DMO active layer. In light of the high short-circuit current densities and fill factors for the Y18-DMO based device and the high value of open circuit voltage of the DBTBT-IC based device, ternary polymer solar cells are fabricated by using ternary active layer (P106 : DBTBT-IC : Y18-DMO) and achieve a power conversion efficiency of 16.49 % with low energy loss of 0.47 eV.

Simultaneous Improvement of Efficiency and Stability of Organic Photovoltaic Cells by using a Cross-Linkable Fullerene Derivative

Improving power conversion efficiencies (PCEs) and stability are two main tasks for organic photovoltaic (OPV) cells. In the past few years, although the PCE of the OPV cells has been considerably improved, the research on device stability is limited. Herein, a cross-linkable material, cross-linked [6,6]-phenyl-C61-butyric styryl dendron ester (c-PCBSD), is applied as an interfacial modification layer on the surface of zinc oxide and as the third component into the PBDB-TF:Y6-based OPV cells to enhance photovoltaic performance and long-term stability. The PCE of the OPV cells that underwent the two-step modification increased from 15.1 to 16.1%. In particular, such OPV cells exhibited much better stability under both thermal and air conditions because of the decreased number of interfacial defects and stable interfacial and active layer morphologies. The results demonstrated that the introduction of a cross-linkable fullerene derivative into the interfacial and active layers is a feasible method to improve the PCE and stability of OPV cells.

Efficient Fused-Ring Extension of A-D-A-Type Non-Fullerene Acceptors by a Symmetric Replicating Core Unit Strategy

The extension of fused aromatic ring core structures is beneficial for enhancing intramolecular charge transfer and effective π conjugation in A-D-A-type (A=acceptor; D=donor) non-fullerene acceptors (NFAs). In this work, a novel strategy involving the extension of a fused-ring core by symmetrically replicating the core unit has been developed, and a novel symmetric fused-12-ring NFA, LC81, has been synthesized. When paired with the wide-bandgap polymer donor PBT1-C, the corresponding organic solar cells (OSCs) showed a high power conversion efficiency of 12.71 %, much higher than that of the device based on the reference NFA, TPTT-4F. Moreover, the LC81-based OSC displayed a lower energy loss and a better ambient stability than the TPTT-4F-based device. Our results indicate that the extension of the fused-ring core by the symmetric replicating core unit strategy is an effective approach to promoting the photovoltaic characteristics of A-D-A-type NFAs.

Miscibility-Controlled Phase Separation in Double-Cable Conjugated Polymers for Single-Component Organic Solar Cells with Efficiencies over 8

A record power conversion efficiency of 8.40 % was obtained in single-component organic solar cells (SCOSCs) based on double-cable conjugated polymers. This is realized based on exciton separation playing the same role as charge transport in SCOSCs. Two double-cable conjugated polymers were designed with almost identical conjugated backbones and electron-withdrawing side units, but extra Cl atoms had different positions on the conjugated backbones. When Cl atoms were positioned at the main chains, the polymer formed the twist backbones, enabling better miscibility with the naphthalene diimide side units. This improves the interface contact between conjugated backbones and side units, resulting in efficient conversion of excitons into free charges. These findings reveal the importance of charge generation process in SCOSCs and suggest a strategy to improve this process: controlling miscibility between conjugated backbones and aromatic side units in double-cable conjugated polymers.

Random terpolymer based on thiophene-thiazolothiazole unit enabling efficient non-fullerene organic solar cells

Developing a high-performance donor polymer is critical for achieving efficient non-fullerene organic solar cells (OSCs). Currently, most high-efficiency OSCs are based on a donor polymer named PM6, unfortunately, whose performance is highly sensitive to its molecular weight and thus has significant batch-to-batch variations. Here we report a donor polymer (named PM1) based on a random ternary polymerization strategy that enables highly efficient non-fullerene OSCs with efficiencies reaching 17.6%. Importantly, the PM1 polymer exhibits excellent batch-to-batch reproducibility. By including 20% of a weak electron-withdrawing thiophene-thiazolothiazole (TTz) into the PM6 polymer backbone, the resulting polymer (PM1) can maintain the positive effects (such as downshifted energy level and reduced miscibility) while minimize the negative ones (including reduced temperature-dependent aggregation property). With higher performance and greater synthesis reproducibility, the PM1 polymer has the promise to become the work-horse material for the non-fullerene OSC community.

Developing Wide Bandgap Polymers Based on Sole Benzodithiophene Units for Efficient Polymer Solar Cells

In this work, a series of sole benzodithiophene-based wide band gap polymer donors, namely PBDTT, PBDTS, PBDTF and PBDTCl, were developed for efficient polymer solar cells (PSCs) by varying the heteroatoms into the conjugated side chains. The effects of sulfuration, fluorination and chlorination were also investigated systematically on the overall properties of these BDT-based polymers. The HOMO levels could be lowered gradually by introducing sulfur, fluorine and chlorine atoms into the side chains, which contributed to the stepwise increased V_oc (from 0.78 V to 0.84 V) in the related PSCs using Y6 as the electron acceptor. This side-chain engineering strategy could promote the polymer chain interactions and fine-tune the phase separation of active blends, leading to enhanced absorption, ordered molecular packing and crystallinity. Among them, the chlorinated PBDTCl exhibited not only high level absorption and crystallinity, but also the most balanced hole/electron charge transport and the most optimized morphology, giving rise to the best PCE of 13.46 % with a V_oc of 0.84 V, a J_sc of 23.16 mA cm^-2 and an FF of 69.2 %. The chlorination strategy afforded PBDTCl synthetic simplicity but high efficiency, showing its promising photovoltaic applications for realizing low-cost practical PSCs in near future.

Fine regulation of crystallisation tendency to optimize the BHJ nanostructure and performance of polymer solar cells

Optimizing the nanostructure of the active layer of polymer solar cells (PSCs) is one of the main challenges to achieve high device performances. The phase separation of the donor polymer and molecular acceptor within the bulk heterojunction (BHJ) layer is often driven by the crystallisation of the acceptor molecules. Hence, a suitable crystallisation tendency of the chosen acceptor is ultimately important. In this work, we identified melting temperature as an indicator for the crystallisation tendency and introduced extended fused-aromatic rings to the end groups of the nonfullerene acceptor molecule to enhance the intermolecular binding energy as well as its crystallisation tendency. The crystallinity, crystal regularity and average crystal size were significantly increased for those molecules with larger fused end groups. The devices containing molecule IDTTC with two fused thiophene rings, which displayed intermediate crystallisation tendency, were found to possess an optimized phase separation scale, balanced hole/electron mobility and highest device performances with the fill factor as high as 73.2% and a power conversion efficiency of 13.49%. With the above observations, we established a new route and paradigm to adjust the crystallisation tendency and BHJ nanostructure of nonfullerene acceptor molecules, thus enhancing the device performances through molecular engineering.

Optimized active layer morphology toward efficient and polymer batch insensitive organic solar cells

Morphology control in laboratory and industry setting remains as a major challenge for organic solar cells (OSCs) due to the difference in film-drying kinetics between spin coating and the printing process. A two-step sequential deposition method is developed to control the active layer morphology. A conjugated polymer that self-assembles into a well-defined fibril structure is used as the first layer, and then a non-fullerene acceptor is introduced into the fibril mesh as the second layer to form an optimal morphology. A benefit of the combined fibril network morphology and non-fullerene acceptor properties was that a high efficiency of 16.5% (certified as 16.1%) was achieved. The preformed fibril network layer and the sequentially deposited non-fullerene acceptor form a robust morphology that is insensitive to the polymer batches, solving a notorious issue in OSCs. Such progress demonstrates that the utilization of polymer fibril networks in a sequential deposition process is a promising approach towards the fabrication of high-efficiency OSCs.

Reliably controlling the morphology in organic solar cells is desired for up-scaling. Here Weng et al. combine the advantages of the fibril network donor and the state of the art Y6 acceptor in a two-step approach to deliver a high efficiency of 16% without batch-to-batch variation.

Carbazole-based green and blue-BODIPY dyads and triads as donors for bulk heterojunction organic solar cells

Two BODIPY derivatives with one (B2) and two (B3) carbazole moieties were synthesized and applied as electron-donor materials in organic photovoltaic cells (OPV). Their optical and electrochemical properties were systematically investigated. These BODIPY dyes exhibit excellent solubility in organic solvents and present high molar extinction coefficients (1.37-1.48 × 10⁵ M^-1 cm^-1) in solutions with absorption maxima at 586 nm for mono-styryl groups and at 672 nm for di-styryl groups. The introduction of the styryl moieties results in a large bathochromic shift and a significant decrease in the HOMO-LUMO energy-gaps. The BODIPY dyes show relatively low HOMO energies ranging from -4.99 to -5.16 eV as determined from cyclic voltammetry measurements. Cyclic voltammetry measurements and theoretical calculations demonstrate that the frontier molecular orbital levels of these compounds match with those of PC₇₁BM as the acceptor, supporting their application as donor materials in solution-processed small molecule bulk heterojunction (BHJ) organic solar cells. After the optimization of the active layer, B2:PC₇₁BM and B3:PC₇₁BM based organic solar cells showed an overall power conversion efficiency of 6.41% and 7.47%, respectively. The higher PCE of the B3-based OSC is ascribed to the more balanced charge transport and exciton dissociation, better crystallinity and molecular packing.

End Group Engineering on the Side Chains of Conjugated Polymers toward Efficient Non-Fullerene Organic Solar Cells

Side chains properties of conjugated polymers, such as the length, branching point, and heteroatom, have been widely studied for application in organic solar cells (OSCs), but the end groups of side chains have been rarely reported. In this work, we systematically explored a series of new conjugated polymers with distinct side-chain end groups for high performance non-fullerene OSCs. The key components for the polymers contained functionalized units as the end groups of side chains, such as Br, alkyloxy (OMe), and alkylthienyl (T) groups. We found that the new conjugated polymers have similar absorption spectra and crystallinity with the polymer without substitution, but they showed distinct photovoltaic performance in solar cells. When the polymer without functionalized units had a power conversion efficiency (PCE) of 9.94%, the modified conjugated polymers provided high PCEs of over 13% with significantly enhanced photocurrent and fill factors. In addition, they also show additive-free and highly stable characteristics. These results demonstrate that end group engineering on side chains is a promising strategy to design new conjugated polymers toward efficient OSCs.

Recent progress in wide bandgap conjugated polymer donors for high-performance nonfullerene organic photovoltaics

This feature article summarizes our recent achievements in the development of wide bandgap polymer donors as high-performance organic photovoltaics.

End-group functionalization of a conjugated azomethine with ureas for property tailoring

A conjugated azomethine end-capped with phenyl-ureas was prepared by a convergent approach. Hydrogen bonding with the ureas was confirmed and the spectroscopic properties could be enhanced with the supramolecular bonds.

Unraveling Correlations between Molecular Properties and Device Parameters of Organic Solar Cells Using Machine Learning

Understanding the relationships between molecular properties and device parameters is highly desired not only to improve the overall performance of an organic solar cell but also to fulfill the requirements of a device for a particular application such as solar-to-fuel energy conversion (high open-circuit voltage (V_OC)) or solar window applications (high short circuit current (J_SC)). In this work, a series of machine learning models are built for three important device characteristics (V_OC, J_SC, and fill factor) using 13 crucial molecular properties as descriptors, resulting in an impressive predictive performance (r = 0.7). These models may play a vital role in designing promising organic materials for a specific photovoltaic application with high V_OC/J_SC. The importance of descriptors for each device parameter is unraveled, which may assist in tuning them and improve understanding of the energy conversion process.

A New Wide Bandgap Donor Polymer for Efficient Nonfullerene Organic Solar Cells with a Large Open-Circuit Voltage

Significant progress has been made in nonfullerene small molecule acceptors (NF-SMAs) that leads to a consistent increase of power conversion efficiency (PCE) of nonfullerene organic solar cells (NF-OSCs). To achieve better compatibility with high-performance NF-SMAs, the direction of molecular design for donor polymers is toward wide bandgap (WBG), tailored properties, and preferentially ecofriendly processability for device fabrication. Here, a weak acceptor unit, methyl 2,5-dibromo-4-fluorothiophene-3-carboxylate (FE-T), is synthesized and copolymerized with benzo[1,2-b:4,5-b']dithiophene (BDT) to afford a series of nonhalogenated solvent processable WBG polymers P1-P3 with a distinct side chain on FE-T. The incorporation of FE-T leads to polymers with a deep highest occupied molecular orbital (HOMO) level of -5.60-5.70 eV, a complementary absorption to NF-SMAs, and a planar molecular conformation. When combined with the narrow bandgap acceptor ITIC-Th, the solar cell based on P1 with the shortest methyl chain on FE-T achieves a PCE of 11.39% with a large V oc of 1.01 V and a J sc of 17.89 mA cm-2. Moreover, a PCE of 12.11% is attained for ternary cells based on WBG P1, narrow bandgap PTB7-Th, and acceptor IEICO-4F. These results demonstrate that the new FE-T is a highly promising acceptor unit to construct WBG polymers for efficient NF-OSCs.

Random Polymer Donor for High-Performance Polymer Solar Cells with Efficiency over 14

Constructing random copolymers has been regarded as an easy and effective approach to design polymer donors for state-of-the-art polymer solar cells (PSCs). In this work, we develop a naphtho[2,3-c]thiophene-4,9-dione-based copolymer PBN-Cl as a donor material for PSCs, and a moderate power conversion efficiency (PCE) of 11.21% is achieved with a relatively low fill factor (FF) of 0.615. We then incorporate a similar acceptor unit benzo[1,2-c:4,5-c']dithiophene-4,8-dione (BDD) into the polymeric backbone of PBN-Cl to tune its photovoltaic performance, and a significantly higher PCE of 14.05% is achieved from the random polymer PBN-Cl-B80 containing 80% BDD unit. The enhanced PCE of the PBN-Cl-B80-based device mainly relies on the higher FF value, resulting from the improved charge mobility properties, reduced bimolecular and trap-assisted recombination, and more appropriate phase separation. The results demonstrate a feasible strategy to tune the photovoltaic performance of polymer donors by constructing a random polymer with a compatible component.