Halide Perovskite Solar Cells for Building Integrated Photovoltaics: Transforming Building Façades into Power Generators

Achievements, challenges, and future prospects for industrialization of perovskite solar cells

In just over a decade, certified single-junction perovskite solar cells (PSCs) boast an impressive power conversion efficiency (PCE) of 26.1%. Such outstanding performance makes it highly viable for further development. Here, we have meticulously outlined challenges that arose during the industrialization of PSCs and proposed their corresponding solutions based on extensive research. We discussed the main challenges in this field including technological limitations, multi-scenario applications, sustainable development, etc. Mature photovoltaic solutions provide the perovskite community with invaluable insights for overcoming the challenges of industrialization. In the upcoming stages of PSCs advancement, it has become evident that addressing the challenges concerning long-term stability and sustainability is paramount. In this manner, we can facilitate a more effective integration of PSCs into our daily lives.

2D Ruddlesden-Popper Perovskites with Polymer Additive as Stable and Transparent Optoelectronic Materials for Building-Integrated Applications

We report on the use of 2D Ruddlesden-Popper (RP) perovskites as optoelectronic materials in building-integrated applications, addressing the challenge of balancing transparency, photoluminescence, and stability. With the addition of polyvinylpyrrolidone (PVP), the 2D RP films exhibit superior transparency compared to their 3D counterparts with an average visible transmittance (AVT) greater than 50% and photoluminescence stability under continuous illumination and 85 °C heat for up to 100 h as bare, unencapsulated films. Structural investigations show a stress relaxation in the 3D perovskite films after degradation from thermal aging that is not observed in the 2D RP films, which retain their phase after thermal and light aging. We also demonstrate ultrasmooth, wide-bandgap 2D Dion-Jacobson (DJ) films with PVP incorporation up to 2.95 eV, an AVT above 70%, and roughnesses of ~2 nm. These findings contribute to the development of next-generation solar materials, paving the way for their integration into built structures.

Ecofriendly Solution Processing of Perovskite Solar Cells Using Water

Perovskite solar cells (PSCs) represent a promising avenue for producing cost-effective solar energy by harnessing sunlight, but challenges persist in their solution processing, which uses a large amount of organic solvent for existing PSC technology. The use of water as a solvent offers an environmentally friendly alternative to traditional solvents, aligning with the global drive for sustainable renewable energy technologies. This Perspective provides an overview of research in the area of PSC fabrication using water as a solvent, highlighting key advancements in the synthesis process. We delve into the kinetics of crystallization and the physical-chemical transformations of perovskite materials in water-based solution processing. Key challenges of the scalability of water-based solution processing for PSC fabrication are discussed. The Perspective sheds light on the broader potential for enhancing the ecofriendliness of perovskite solar cell technologies.

Preventing lead leakage in perovskite solar cells and modules with a low-cost and stable chemisorption coating

Despite the promising commercial prospects of perovskite solar cells, the issue of lead toxicity continues to hinder their future industrial applications. Here, we report a low-cost and rapidly degraded sulfosuccinic acid-modified polyvinyl alcohol (SMP) coating that prevents lead leakage and enhances device stability without compromising device performance. Even under different strict conditions (simulated heavy rain, acid rain, high temperatures, and competing ions), the coatings effectively prevent lead leakage by over 99%. After 75 days of outdoor exposure, the coating still demonstrates similar lead sequestration efficiency (SQE). In addition, it can be applied to different device structures (n-i-p and p-i-n) and modules, with over 99% SQE, making it a general method for preventing lead leakage.

Doping with KBr to Achieve High-Performance CsPbBr3 Semitransparent Perovskite Solar Cells

Wide-bandgap semitransparent perovskite photovoltaics are emerging as one of the ideal candidates for building-integrated photovoltaics (BIPV). However, surface defects in inorganic CsPbBr3 perovskite prepared by vapor deposition severely limit the optoelectronic performance of perovskite solar cells. To address this issue, a strategy of doping a trace amount of KBr into perovskite by vapor deposition is adopted, effectively improving the quality of the film, reducing surface defect concentration, and enhancing the transportation and extraction of charge carriers. Simultaneously, fully physical vapor deposition technology is employed to fabricate perovskite solar cells with an average visible light transmittance of 44%. These devices exhibited an ultrahigh open-circuit voltage of 1.55 V and a superior power conversion efficiency (PCE) of 7.28%, demonstrating excellent moisture and heat resistance. Moreover, the corresponding 5 cm × 5 cm modules achieve a PCE of 5.35% with great thermal insulation capability. This work provides an approach for fabricating highly efficient all-inorganic perovskite solar cells with high average visible light transmittance, demonstrating new insights into their application in building-integrated photovoltaics.

Perovskite Smart Windows: The Light Manipulator in Energy-Efficient Buildings

Uncontrolled sunlight entering through windows contributes to substantial heating and cooling demands in buildings, which leads to high energy consumption from the buildings. Recently, perovskite smart windows have emerged as innovative energy-saving technologies, offering the potential to adaptively control indoor solar heat gain through their impressive sunlight modulation capabilities. Moreover, harnessing the high-efficiency photovoltaic properties of perovskite materials, these windows have the potential to generate power, thereby realizing more advanced windows with combined light modulation and energy harvesting capabilities. This review summarizes the recent advancements in various chromic perovskite materials for achieving light modulation, focusing on both perovskite structures and underlying switching mechanisms. The discussion also encompasses device engineering strategies for smart windows, including the improvement of their optical and transition performance, durability, combination with electricity generation, and the evaluation of their energy-saving performance in building applications. Furthermore, the challenges and opportunities associated with perovskite smart windows are explicated, aimed at stimulating more academic research and advancing their pragmatic implementation for building energy efficiency and sustainability.

Structurally colored semitransparent perovskite solar cells using one-step deposition of self-ordering microgel particles

Semitransparent perovskite solar cells (STPSCs) have excellent potential for widespread application as building integrated photovoltaics. Widespread application of STPSCs could result in decreased CO2 footprints for buildings. Unfortunately, STPSCs tend to have poor aesthetic qualities (being usually red-brown in color) and low stability. Building on our previous work, here we use new poly(N-isopropylacrylamide) microgels (PNP MGs) to provide highly ordered non-close packed arrays within perovskite films that reflect some of the incident light to provide structural color to STPSCs. (MGs are swellable crosslinked polymer colloid particles.) We introduce PNP MGs into two different perovskites and achieve a wide gamut of reflected color and iridescence from the perovskite films. Devices containing the MGs have average visible transparency (AVT) values of greater than 25%. The best PCE for a MG-containing STPSC is 10.60% compared to 9.14% for the MG-free control. The MGs not only introduce structural color to the STPSCs but increase the PCE and stability. Equations are provided that enable the reflected color to be predicted from the formulation used to deposit the films. Our work shows that the self-ordering tendency of PNP MGs gives a viable new method for introducing structural color into STPSCs. Because our one-step method for introducing structural color into STPSCs is general, does not introduce any additional processing steps and is scalable whilst also improving device stability, this study may bring deployment of STPSCs closer.

Highly-efficient heterojunction solar cells based on 2D Janus transition-metal nitride halide (TNH) monolayers with ultrahigh carrier mobility

Symmetry breaking has a crucial effect on electronic band structure and subsequently affects the light-absorption coefficient of monolayers. We systematically report a family of two-dimensional (2D) Janus transition-metal nitride halides (TNHs, T = Ti, Zr, Hf, Fe, Pd, Pt, Os, and Re; H = Cl and F) with breaking of both in-plane and out-of-plane structural symmetry. The dynamical, thermal and mechanical stabilities are calculated to check the stability of the Janus TNHs. The electric properties of ten TNHs are studied via the HSE06+SOC method and the band gaps range from 0.93 eV (PdNCl) to 4.74 eV (HfNCl). Desirable light adsorption coefficients of up to 105 cm-1 are obtained for the Janus TNHs with no central symmetry. The Janus OsNCl monolayer shows excellent electrical transport properties and ultrahigh carrier mobility (104 cm2 V-1 s-1). Heterojunctions formed by stacking two Janus TNH monolayers are further investigated for solar cell applications. Eight of the heterojunctions have type-II band alignments. Surprisingly, the OsNCl/FeNCl heterojunction has a power conversion efficiency (PCE) of 23.45%, which is a larger value compared to the PCE of GeSe/SnSe heterostructures (21.47%). The optical properties and the built-in electric field of the OsNCl/FeNCl heterojunction are investigated. These results indicate that the stable Janus TNH monolayers have potential applications in photoelectric devices, and the vertical heterojunctions can be used in solar cells.

Printable High-Efficiency and Stable FAPbBr3 Perovskite Solar Cells for Multifunctional Building-Integrated Photovoltaics

Perovskite solar cells (PSCs) show great promise for next-generation building-integrated photovoltaic (BIPV) applications because of their abundance of raw materials, adjustable transparency, and cost-effective printable processing. Owing to the complex perovskite nucleation and growth control, the fabrication of large-area perovskite films for high-performance printed PSCs is still under active investigation. Herein, the study proposes an intermediate-phase-transition-assisted one-step blade coating for an intrinsic transparent formamidinium lead bromide (FAPbBr3 ) perovskite film. The intermediate complex optimizes the crystal growth path of FAPbBr3 , resulting in a large-area, homogeneous, and dense absorber film. A champion efficiency of 10.86% with high open-circuit voltage up to 1.57 V is obtained with a simplified device architecture of glass/FTO/SnO2 /FAPbBr3 /carbon. Moreover, the unencapsulated devices maintain 90% of their initial power conversion efficiency after aging at 75 °C for 1000 h in ambient air, and 96% after maximum power point tracking for 500 h. The printed semitransparent PSCs, with average visible light transmittance over 45%, demonstrate high efficiencies for both small devices (8.6%) and 10 × 10 cm2 modules (5.55%). Finally, the ability to customize the color, transparency, and thermal insulation properties of FAPbBr3 PSCs makes them high prospects as multifunctional BIPVs.

Progress and Challenges Toward Effective Flexible Perovskite Solar Cells

The demand for building-integrated photovoltaics and portable energy systems based on flexible photovoltaic technology such as perovskite embedded with exceptional flexibility and a superior power-to-mass ratio is enormous. The photoactive layer, i.e., the perovskite thin film, as a critical component of flexible perovskite solar cells (F-PSCs), still faces long-term stability issues when deformation occurs due to encountering temperature changes that also affect intrinsic rigidity. This literature investigation summarizes the main factors responsible for the rapid destruction of F-PSCs. We focus on long-term mechanical stability of F-PSCs together with the recent research protocols for improving this performance. Furthermore, we specify the progress in F-PSCs concerning precise design strategies of the functional layer to enhance the flexural endurance of perovskite films, such as internal stress engineering, grain boundary modification, self-healing strategy, and crystallization regulation. The existing challenges of oxygen-moisture stability and advanced encapsulation technologies of F-PSCs are also discussed. As concluding remarks, we propose our viewpoints on the large-scale commercial application of F-PSCs.

Innovative Approaches to Semi-Transparent Perovskite Solar Cells

Perovskite solar cells (PSCs) are advancing rapidly and have reached a performance comparable to that of silicon solar cells. Recently, they have been expanding into a variety of applications based on the excellent photoelectric properties of perovskite. Semi-transparent PSCs (ST-PSCs) are one promising application that utilizes the tunable transmittance of perovskite photoactive layers, which can be used in tandem solar cells (TSC) and building-integrated photovoltaics (BIPV). However, the inverse relationship between light transmittance and efficiency is a challenge in the development of ST-PSCs. To overcome these challenges, numerous studies are underway, including those on band-gap tuning, high-performance charge transport layers and electrodes, and creating island-shaped microstructures. This review provides a general and concise summary of the innovative approaches in ST-PSCs, including advances in the perovskite photoactive layer, transparent electrodes, device structures and their applications in TSC and BIPV. Furthermore, the essential requirements and challenges to be addressed to realize ST-PSCs are discussed, and the prospects of ST-PSCs are presented.

Biomimetic Approaches to "Transparent" Photovoltaics: Current and Future Applications

There has been a surge in the interest for (semi)transparent photovoltaics (sTPVs) in recent years, since the more traditional, opaque, devices are not ideally suited for a variety of innovative applications spanning from smart and self-powered windows for buildings to those for vehicle integration. Additional requirements for these photovoltaic applications are a high conversion efficiency (despite the necessary compromise to achieve a degree of transparency) and an aesthetically pleasing design. One potential realm to explore in the attempt to meet such challenges is the biological world, where evolution has led to highly efficient and fascinating light-management structures. In this mini-review, we explore some of the biomimetic approaches that can be used to improve both transparent and semi-transparent photovoltaic cells, such as moth-eye inspired structures for improved performance and stability or tunable, coloured, and semi-transparent devices inspired by beetles' cuticles. Lastly, we briefly discuss possible future developments for bio-inspired and potentially bio-compatible sTPVs.

Textured Stainless Steel as a Platform for Black Mg2Si/Si Heterojunction Solar Cells with Advanced Photovoltaic Performance

This paper reports on a facile bottom-up method for the direct integration of a silicon (Si)-magnesium silicide (Mg₂Si) heterojunction solar cell (HSC) with a textured rear reflector made of stainless steel (SS). Modified wet chemical etching and post processing of SS substrates resulted in the formation of both a rough surface texture and diffusion barrier layer, consisting of magnetite (Fe₃O₄) with reduced optical reflection. Then, Si, Mg₂Si and CaSi₂ layers were stepwise thermally evaporated onto the textured SS surface. No traces of Fe and Cr silicide phases were detected by Raman spectroscopy, confirming effective suppression of impurity diffusion from the SS to the upper layers at least at temperatures required for Si deposition, as well as Mg₂Si and CaSi₂ formation. The obtained black-SS/Fe₃O₄/Si/Mg₂Si/CaSi₂ sample preserved, to some extent, its underlying textured morphology and demonstrated an averaged reflection of 15% over the spectral range of 200-1800 nm, while its prototype HSC possessed a wideband photoresponse with a photoelectric conversion efficiency of 7.5% under AM1.5 illumination. Moreover, Si layers deposited alone onto a black-SS substrate demonstrated competitive antireflection properties compared with black Si (b-Si) obtained by traditional top-down etching approaches, and hybrid b-Si/textured-SS structures with a glue-bonded interlayer.

Two-dimensional IV-VA3 monolayers with enhanced charge mobility for high-performance solar cells

High-performance photovoltaics (PVs) constitute a subject of extensive research efforts, in which silicon (Si)-based solar cells (SCs) have been widely commercialized. However, the low carrier mobility of Si-based SCs can limit the effective charge separation, thereby negatively impacting the device performance. Here, via calculating the physicochemical and PV performance based on density functional theory, we demonstrate SCs based on two-dimensional (2D) group IV and V compounds with an AX₃ configuration. Firstly, the cleavage energies of AX₃ (A = Si, Ge; X = P, As, and Sb) are calculated to be less than 1 J m^-2, providing an experimental feasibility to be exfoliated from the corresponding bulk. Secondly, electronic and optical properties have been systematically investigated. To be specific, the band gap of monolayer AX₃ falls in the range of 1.11-1.27 eV, which is comparable with that of Si. Significantly, the electron mobility of monolayer AX₃ can reach as high as ∼30 000 cm² V^-1 s^-1, which is one order of magnitude higher than that of Si. Furthermore, the optical absorbance of monolayer SiAs₃, SiP₃ and GeAs₃ exhibits high coefficients in visible light. Therefore, we believe that our designed AX₃-based PV systems with power conversion efficiency of 20% can offer great potential in the application of high-performance two-dimension-based PVs.