In Operando GISAXS and GIWAXS Stability Study of Organic Solar Cells Based on PffBT4T-2OD:PC71BM with and without Solvent Additive

Suppressed Degradation Process of PBDB-TF-T1:BTP-4F-12-Based Organic Solar Cells with Solid Additive Atums Green

Solid additives have garnered significant attention due to their numerous advantages over liquid additives. This study explores the potential of the green-fluorescent conjugated polymer denoted Atums Green as a solid additive in green-solvent-based PBDB-TF-T1:BTP-4F-12 solar cells. Even tiny amounts of Atums Green doping significantly improve the device performance. For the reference solar cell without any additive, we find that device degradation is not caused by chemical redox reactions but by changes in crystallinity and microstructure evolution during aging in air under illumination. Operando GIWAXS and GISAXS are used to investigate the structure evolution. We discover a four-stage degradation process for the reference cell. In general, the lattice spacing and crystallite coherence length decrease, while the domain sizes increase, which causes the loss of shirt-circuit current JSC and fill factor FF. Furthermore, a decomposition component is detected in GIWAXS and GISAXS, corresponding to the loss of the open-circuit voltage VOC. Atums Green doping effectively suppresses the evolution of crystallinity and domain sizes as well as the continuous decomposition, thereby enhancing the device stability under illumination in air. This finding reveals the kinetic degradation process of organic solar cells, establishes a correlation between the morphological properties and device performance, and further demonstrates the promising potential of Atums Green doping in organic solar cells.

Dual Additive Strategy with Quasi-Planar Heterojunction Architecture Assisted in Morphology Optimization for High-Efficiency Organic Solar Cells

Achieving high-performance and stable organic solar cells (OSCs) remains a critical challenge, primarily due to the precise optimization required for active layer morphology. Herein, this work reports a dual additive strategy using 3,5-dichlorobromobenzene (DCBB) and 1,8-diiodooctane (DIO) to optimize the morphology of both bulk-heterojunction (BHJ) and quasi-planar heterojunction (Q-PHJ) based on donor D18 and acceptor BTP-eC9. The systematic results reveal that the dual additive strategy significantly promotes phase separation while inhibiting excessive aggregation, which, in turn, improves molecular order and crystallization. As a result, BHJ and Q-PHJ OSCs processed with dual additive DIO + DCBB achieve impressive power conversion efficiencies of 17.77% and 18.60%, respectively, the highest reported values for dual additive-processed OSCs. The superior performance is attributed to improved charge transport and reduced recombination losses, as evidenced by higher short-circuit current densities (JSC) and fill factors (FF). Importantly, Q-PHJ OSCs processed with either DCBB or DIO + DCBB, in comparison to BHJ OSCs, exhibit exceptional shelf-stability, maintaining 80% of their initial power conversion efficiency after 2660 and 2193 h, respectively. These findings underscore the potential of dual additive strategies to advance the development of stable, high-efficiency OSCs suitable for large-area fabrication, marking a significant step forward in renewable energy technology.

An Indacenodithienothiophene-Based Wide Bandgap Small Molecule Guest for Efficient and Stable Ternary Organic Solar Cells

The strategic and logical development of the third component (guest materials) plays a pivotal and intricate role in improving the efficiency and stability of ternary organic solar cells (OSCs). In this study, a novel guest material with a wide bandgap, named IDTR, is designed, synthesized, and incorporated as the third component. IDTR exhibits complementary absorption characteristics and cascade band alignment with the PM6:Y6 binary system. Morphological analysis reveals that the introduction of IDTR results in strong crystallinity, good miscibility, and proper vertical phase distribution, thereby realizing heightened and balanced charge transport behavior. Remarkably, the novel ternary OSCs have exhibited a significant enhancement in photovoltaic performance. Consequently, open-circuit voltage (VOC), short-circuit current (JSC), and fill factor (FF) have all witnessed substantial improvements with a remarkable power conversion efficiency (PCE) of 18.94% when L8-BO replaced Y6. Beyond the pronounced improvement in photovoltaic performance, superior device stability with a T80 approaching 400 h is successfully achieved. This achievement is attributed to the synergistic interplay of IDTR, providing robust support for the overall enhancement of performance. These findings offer crucial guidance and reference for the design and development of efficient and stable OSCs.

High-Performance PM6:Y6-Based Ternary Solar Cells with Enhanced Open Circuit Voltage and Balanced Mobilities via Doping a Wide-Band-Gap Amorphous Acceptor

Great progress has been made in organic solar cells (OSCs) in recent years, especially after the report of the highly efficient small-molecule electron acceptor Y6. However, the relatively low open circuit voltage (VOC) and unbalanced charge mobilities remain two issues that need to be resolved for further improvement in the performance of OSCs. Herein, a wide-band-gap amorphous acceptor IO-4Cl, which possessed a shallower lowest unoccupied molecular orbital (LUMO) energy level than Y6, was introduced into the PM6:Y6 binary system to construct a ternary device. The mechanism study revealed that the introduced IO-4Cl was alloyed with Y6 to prevent the overaggregation of Y6 and offer dual channels for effective hole transportation, resulting in balanced hole and electron mobilities. Taking these advantages, an enhanced VOC of 0.894 V and an improved fill factor of 75.58% were achieved in the optimized PM6:Y6:IO-4Cl-based ternary device, yielding a promising power conversion efficiency (PCE) of 17.49%, which surpassed the 16.72% efficiency of the PM6:Y6 binary device. This work provides an alternative solution to balance the charge mobilities of PM6:Y6-based devices by incorporating an amorphous high-performance LUMO A-D-A small molecule as the third compound.

Control of Multi-Fluorination Number and Position in D-π-A Type Polymers and Their Impact on High-Voltage Organic Photovoltaics

Exploring the structure-performance relationship of high-voltage organic solar cells (OSCs) is significant for pushing material design and promoting photovoltaic performance. Herein, we chose a D-π-A type polymer composed of 4,8-bis(thiophene-2-yl)-benzo[1,2-b:4,5-b']dithiophene (BDT-T) and benzotriazole (BTA) units as the benchmark to investigate the effect of the fluorination number and position of the polymers on the device performance of the high-voltage OSCs, with a benzotriazole-based small molecule (BTA3) as the acceptor. F00, F20, and F40 are the polymers with progressively increasing F atoms on the D units, while F02, F22, and F42 are the polymers with further attachment of F atoms to the BTA units based on the above three polymers. Fluorination positively affects the molecular planarity, dipole moment, and molecular aggregations. Our results show that VOC increases with the number of fluorine atoms, and fluorination on the D units has a greater effect on VOC than on the A unit. F42 with six fluorine atom substitutions achieves the highest VOC (1.23 V). When four F atoms are located on the D units, the short-circuit current (JSC) and fill factor (FF) plummet, and before that, they remain almost constant. The drop in JSC and FF in F40- and F42-based devices may be attributed to inefficient charge transfer and severe charge recombination. The F22:BTA3 system achieves the highest power conversion efficiency of 9.5% with a VOC of 1.20 V due to the excellent balance between the photovoltaic parameters. Our study provides insights for the future application of fluorination strategies in molecular design for high-voltage organic photovoltaics.

Chalcogen Atoms Regulate the Organic Solar Cell Performance of B-N-Based Polymer Donors

Donor polymers play a key role in the development of organic solar cells (OSCs). B-N-based polymer donors, as new types of materials, have attracted a lot of attention due to their special characteristics, such as high E(T1), small ΔEST, and easy synthesis, and they can be processed with real green solvents. However, the relationship between the chemical structure and device performance has not been systematically studied. Herein, chalcogen atoms that regulate the OSCs performance of B-N-based polymer donors were systematically studied. Fortunately, the substitution of a halogen atom did not affect the high E(T1) and small ΔEST character of the B-N-based polymer. The absorption and energy levels of the polymer were systematically regulated by O, S, and Se atom substitution. The PBNT-TAZ:Y6-BO-based OSCs device demonstrated a high power conversion efficiency of 15.36%. Moreover, the layer-by-layer method was applied to further optimize the device performance, and the PBNT-TAZ/Y6-BO-based OSCs device yielded a PCE of 16.34%. Consequently, we have systematically demonstrated how chalcogen atoms modulated the electronic properties of B-N-based polymers. Detailed and systematic structure-performance relationships are important for the development of next-generation B-N-based materials.

Strategy to simulate and fit 2D grazing-incidence small-angle X-ray scattering patterns of nanostructured thin films

Grazing-incidence small-angle X-ray scattering (GISAXS) is a widely used method for the characterization of the nanostructure of supported thin films and enables time-resolved in situ measurements. The 2D scattering patterns contain detailed information about the nanostructures within the film and at its surface. However, this information is distorted not only by the reflection of the X-ray beam at the substrate-film interface and its refraction at the film surface but also by scattering of the substrate, the sample holder and other types of parasitic background scattering. In this work, a new, efficient strategy to simulate and fit 2D GISAXS patterns that explicitly includes these effects is introduced and demonstrated for (i) a model case nanostructured thin film on a substrate and (ii) experimental data from a microphase-separated block copolymer thin film. To make the protocol efficient, characteristic linecuts through the 2D GISAXS patterns, where the different contributions dominate, are analysed. The contributions of the substrate and the parasitic background scattering - which ideally are measured separately - are determined first and are used in the analysis of the 2D GISAXS patterns of the nanostructured, supported film. The nanostructures at the film surface and within the film are added step by step to the real-space model of the simulation, and their structural parameters are determined by minimizing the difference between simulated and experimental scattering patterns in the selected linecuts. Although in the present work the strategy is adapted for and tested with BornAgain, it can be easily used with other types of simulation software. The strategy is also applicable to grazing-incidence small-angle neutron scattering.

Reexamining the Role of Solution-Cast Ferroelectric Polymer Interlayer toward Enhanced Efficiency and Stability in Conventional Organic Solar Cells

Interfacial modification is crucial for achieving efficient and stable organic solar cells (OSCs). Herein, an N,N-dimethylformamide (DMF) solution-cast poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE)) interlayer was applied to enhance the efficiency and stability of a range of OSCs, and the underlying mechanism was revealed via morphological and device physics studies. DMF rinse during the P(VDF-TrFE) interlayer casting process strengthens π-π stacking of the active layer with fibril aggregation, optimized phase separation, and vertical component distribution, while the P(VDF-TrFE) interlayer with rich diploes contributes to increased surface potential and internal electric field. The synergistic effect of the P(VDF-TrFE) interlayer and DMF rinse increases the PCEs of PM6:IT-4F, PM6:C5-16, and PM6:L8-BO OSCs from 12.7, 17.9, and 18.2% to 13.1, 18.7, and 18.8%, respectively. Additionally, OSCs containing the P(VDF-TrFE) interlayer also showed improved storage stability.

Prospects of glove-box versus air-processed organic solar cells

In the search for alternate green energy sources to offset dependence on fossil fuels, solar energy can certainly meet two needs with one deed: fulfil growing global energy demands due to its non-depletable nature and lower greenhouse gas emissions. As such, third generation thin film photovoltaic technology based organic solar cells (OSCs) can certainly play their role in providing electricity at a competing or lower cost than 1st and 2nd generation solar technologies. As OSCs are still at an early stage of research and development, much focus has been placed on improving power conversion efficiencies (PCEs) inside a controlled environment i.e. a glove-box (GB) filled with an inert gas such as N₂. This was necessary until now, to control and study the local nanomorphology of the spin-coated blend films. For OSCs to compete with other solar energy technologies, OSCs should produce similar or even better morphologies in an open environment i.e. air, such that air-processed OSCs can result in similar PCEs in comparison to their GB-processed counterparts. In this review, we have compared GB- vs. air-processed OSCs from morphological and device physics aspects and underline the key features of efficient OSCs, processed in either GB or air.

Morphological Insights into the Degradation of Perovskite Solar Cells under Light and Humidity

Perovskite solar cells (PSCs) have achieved competitive power conversion efficiencies compared with established solar cell technologies. However, their operational stability under different external stimuli is limited, and the underlying mechanisms are not fully understood. In particular, an understanding of degradation mechanisms from a morphology perspective during device operation is missing. Herein, we investigate the operational stability of PSCs with CsI bulk modification and a CsI-modified buried interface under AM 1.5G illumination and 75 ± 5% relative humidity, respectively, and concomitantly probe the morphology evolution with grazing-incidence small-angle X-ray scattering. We find that volume expansion within perovskite grains, induced by water incorporation, initiates the degradation of PSCs under light and humidity and leads to the degradation of device performance, in particular, the fill factor and short-circuit current. However, PSCs with modified buried interface degrade faster, which is ascribed to grain fragmentation and increased grain boundaries. In addition, we reveal a slight lattice expansion and PL redshifts in both PSCs after exposure to light and humidity. Our detailed insights from a buried microstructure perspective on the degradation mechanisms under light and humidity are essential for extending the operational stability of PSCs.

Asymmetric Polymer Additive for Morphological Regulation and Thermally Stable Organic Solar Cells

High thermal stability is crucial for the commercialization of organic solar cells (OSCs). The thermal stability of OSCs has been improved using the tailoring blend morphology of bulk heterojunctions (BHJs). Herein, we demonstrated thermally stable OSCs in a ternary blended system containing low-crystalline semiconducting polymers (asy-PNDI1FTVT and PTB7-Th) and a non-fullerene acceptor (Y6). The asymmetric n-type semiconducting polymer (asy-PNDI1FTVT) differed from general symmetric semiconducting polymers as it randomly substituted fluorine atoms at the donor moiety (TVT), resulting in significantly lower crystallinity. asy-PNDI1FTVT in PTB7-Th:Y6 exhibited a well-mixed morphology at the BHJ and efficiently facilitated the charge dissociation process with an enhanced fill factor and power conversion efficiency. Furthermore, the ternary system of PTB7-Th:Y6:asy-PNDI1FTVT suppressed phase separation with negligible burn-in loss and performance degradation under thermal stress. The experiments showed that our devices without encapsulation retained over 90% of their initial efficiencies after 100 h at 65 °C. These results show significant potential for the development of thermally stable OSCs with reasonable efficiency.

Noncovalent wedging effect catalyzed the cis to syn transformation of a surface-adsorbed polymer backbone toward an unusual thermodynamically stable supramolecular product

The significant influence of noncovalent interactions on catalytic processes has been recently appreciated but is still in its infancy. In this report, it is found that wedging Me-PTCDI (small-molecule) between the alkyl chains of PffBT4T-2OD (polymer) and a graphite substrate can reduce the energy barrier of flipping over the surface-adsorbed alkylthiophene group from the cis to syn conformation, revealing the catalytic role of Me-PTCDI via a noncovalent wedging effect. The wedging of Me-PTCDI brings the interactions between the alkyl chains and substrate to a very weak level by lifting up the alkyl chains, which eliminates the major hindrance of the flipping process to one main factor: the torsion of the dihedral angles of the thiophene group. The Me-PTCDI/syn PffBT4T-2OD arrangement shows unusual stability compared to the cis one because the syn conformation allows the alkyl chains to construct dense lamella and facilitates interactions between Me-PTCDI and the syn PffBT4T-2OD backbones. The results are helpful for boosting the development of noncovalent catalysis and bottom-up fabrications toward devices functionalized at a molecular level.

Non-Halogenated Solvents and Layer-by-Layer Blade-Coated Ternary Organic Solar Cells via Cascade Acceptor Adjusting Morphology and Crystallization to Reduce Energy Loss

The power conversion efficiency (PCE) of halogenated solvent spin-coated organic solar cells (OSCs) has been boosted to a high level (>18%) by developing efficient photovoltaic materials and precise morphological control. However, the PCE of OSCs prepared from non-halogenated solvents and with a scalable printing process is far behind, limited by tough morphology manipulation. Herein, we have fabricated ternary OSCs by using layer-by-layer (LBL) blade-coating and a non-halogenated solvent. The ternary OSCs based on the PM6:IT-M(1:0.2)/BTP-eC9 active layer are processed with the hydrocarbon solvent 1,2,4-trimethylbenzene with no need of any additives and post-treatment. The vertical donor/acceptor distribution is optimized by LBL blade-coating within the PM6:IT-M(1:0.2)/BTP-eC9 active layer. The cascade acceptor IT-M blended in PM6 not only attenuates the damage of BTP-eC9 to the PM6 crystallization, leading to a dense nanofiber-like morphology, but also prefers to reside between PM6 and BTP-eC9 to form a cascade energy level alignment for a fast charge-transfer process. Finally, the improved morphology and crystallization lead to a reduced molecular recombination, low energy loss, and high open-circuit voltage. The prepared non-halogenated solvent and LBL blade-coated OSCs achieve a PCE of 17.16%. The work provides an approach to fabricate hydrocarbon solvent-processed high-performance OSCs by employing LBL blade-coating and a ternary strategy.

Tailoring the Morphology's Microevolution for Binary All-Polymer Solar Cells Processed by Aromatic Hydrocarbon Solvent with 16.22% Efficiency

Herein, we report a systematic solvent selection for eco-friendly processed binary all-polymer solar cells (APSCs) with decent power conversion efficiencies (PCEs). Three typical solvents, toluene, o-xylene, and 1,2,4-trimethylbezene, are chosen and compared. The device enabled by o-xylene exhibits the most outstanding PCE of 16.22%, thanks to its favorable morphology, which is to say a well-formed face-on orientation packing motif and a suitable crystallinity and size of phase segregation. Consequently, the solar cell affords sufficient charge generation, as well as efficient and balanced charge transport, which are all positive to pursuing high efficiency. This work offers an understanding of using complete solvent selection as the strategy to realize high-performance devices by sophisticatedly controlling the morphology.

Gold(III) Porphyrin Was Used as an Electron Acceptor for Efficient Organic Solar Cells

The widespread use of nonfullerene-based electron-accepting materials has triggered a rapid increase in the performance of organic photovoltaic devices. However, the number of efficient acceptor compounds available is rather limited, which hinders the discovery of new, high-performing donor:acceptor combinations. Here, we present a new, efficient electron-accepting compound based on a hitherto unexplored family of well-known molecules: gold porphyrins. The electronic properties of our electron-accepting gold porphyrin, named VC10, were studied by UV-Vis spectroscopy and by cyclic voltammetry (CV) , revealing two intense optical absorption bands at 500-600 and 700-920 nm and an optical bandgap of 1.39 eV. Blending VC10 with PTB7-Th, a donor polymer, which gives rise to an absorption band at 550-780 nm complementary to that of VC10, enables the fabrication of organic solar cells (OSCs) featuring a power conversion efficiency of 9.24% and an energy loss of 0.52 eV. Hence, this work establishes a new approach in the search for efficient acceptor molecules for solar cells and new guidelines for future photovoltaic material design.

How to Choose an Interfacial Modifier for Organic Photovoltaics Using Simple Surface Energy Considerations

Organic photovoltaics are typically composed of at least four different materials, including the donor and acceptor components of the bulk heterojunction, the interfacial layers at each electrode, the electrodes themselves, and solution additives that may persist in the final sandwich structure. The interplay of surface energies between these different layers is profoundly complex, as the deposition and annealing of one layer on top of another may be influenced by the surface energy of these interfaces. While the energy levels of one layer with respect to adjacent layers are important to facilitate charge separation and collection at the electrodes, the relative surface energies of the interfaces in contact with the multicomponent bulk heterojunction can be beneficial or disadvantageous, or be neutral, with respect to the performance of the OPV device. Because the bulk heterojunction is a mixture of donor and acceptor polymers and/or small molecules, the accumulation of one of the components on the underlying electrode interface can be driven by surface energy considerations. A donor- or acceptor-rich interface may affect charge carrier flow to the electrode, thus affecting the overall efficiency. Here, ITO/PEDOT:PSS electrodes in forward organic photovoltaic devices are treated with five different thin interfacial layers to change the relative surface energy of this electrode with respect to the adjacent bulk heterojunction. Contact angle measurements with four probe liquids enable calculation of the surface energies, and the results are compared with the performance of forward-biased organic photovoltaic devices. Time-of-flight secondary ion mass spectrometry results substantiate the predictions of gradients in the bulk heterojunction layers, and grazing-incidence wide-angle X-ray scattering measurements show the impact on the polymer crystallites. Thus, a simple algorithm based on surface energy considerations may inform which interfacial layer for a given bulk heterojunction in an organic photovoltaic device can be the most appropriate.

State of the Art and Prospects for Halide Perovskite Nanocrystals

Metal-halide perovskites have rapidly emerged as one of the most promising materials of the 21st century, with many exciting properties and great potential for a broad range of applications, from photovoltaics to optoelectronics and photocatalysis. The ease with which metal-halide perovskites can be synthesized in the form of brightly luminescent colloidal nanocrystals, as well as their tunable and intriguing optical and electronic properties, has attracted researchers from different disciplines of science and technology. In the last few years, there has been a significant progress in the shape-controlled synthesis of perovskite nanocrystals and understanding of their properties and applications. In this comprehensive review, researchers having expertise in different fields (chemistry, physics, and device engineering) of metal-halide perovskite nanocrystals have joined together to provide a state of the art overview and future prospects of metal-halide perovskite nanocrystal research.

Tricyclic or Pentacyclic D Units: Design of D-π-A-Type Copolymers for High VOC Organic Photovoltaic Cells

Although there are several electron-donating (D) units, only the classic benzo[1,2-b:4,5-b']dithiophenes (BDT) unit was utilized to develop D-π-A-type copolymers for high-voltage organic photovoltaic (OPV) cells. Hence, in this work, we chose two tricyclic D units, BDT and benzo[1,2-b:4,5-b']difurans (BDF), together with one pentacyclic ring, dithieno[2,3-d;2',3'-d']benzo[1,2-b;4,5-b']dithiophenes (DTBDT), to comprehensively study the effect of different D units on the optoelectronic properties and photovoltaic performance. By copolymerized with the benzo[1,2,3]triazole (BTA) electron-accepting unit, the final copolymers J52-Cl, F11, and PE52 were combined with a nonfullerene acceptor (NFA) F-BTA3 according to the "Same-A-Strategy." As we preconceived, all the three single-junction OPV cells can obtain high open-circuit voltage (V_OC) over 1.10 V. Although the tricyclic D unit of BDF exhibits a slightly lower V_OC of 1.12 V because of its mildly larger energy loss of 0.698 eV, its higher carrier mobilities and exciton dissociation efficiency strikingly boost the short-circuit current (J_SC) and fill factor, which contribute to a comparable PCE of 10.04% with J52-Cl (10.10%). However, the DTBDT-based polymer PE52 shows the worst performance with a PCE of 6.78% and a V_OC of 1.14 V, owing to the higher bimolecular recombination and disordered molecular stacking. Our results indicate that tricyclic D units should be a better choice for constructing D-π-A-type polymers for high-voltage photovoltaic materials than the pentacyclic analogues.

All-Polymer Solar Cells Approaching 12% Efficiency with a New π-Conjugated Polymer Donor Enabled by a Nonhalogenated Solvent Process

High efficiency and nonhalogenated solvent processing are important issues for commercial application of all-polymer solar cells (all-PSCs). In this regard, we increased the photovoltaic performance of all-PSCs to a benchmark power conversion efficiency (PCE) of 11.66% by manipulating the pre-aggregation of a new π-conjugated polymer donor (Nap-SiBTz) using toluene as a solvent. This use of Nap-SiBTz enhanced the absorption coefficient (λ_max = 9.30 × 10⁴ cm^-1), increased charge carrier mobility, suppressed trap-assisted recombination, improved bulk heterojunction morphology, and resulted in high PCEs of all-PSCs with an active layer thickness of 200 nm. To overcome severe charge recombination and energy losses, a 1-phenylnapthalene additive was used to achieve a well-ordered microstructure and molecular packing that inherently improved the device performances. The resulting encapsulation-free devices exhibited good ambient and thermal stabilities. The results of this study augur well for the future of the roll-to-roll production of all-PSCs.

Electronic effects of nano-confinement in functional organic and inorganic materials for optoelectronics

This review provides a comprehensive overview of the electronic effects of nano-confinement (from 1D to 3D geometries) on optoelectronic materials and their applications.

Effects on Photovoltaic Characteristics by Organic Bilayer- and Bulk-Heterojunctions: Energy Losses, Carrier Recombination and Generation

We investigate the photovoltaic characteristics of organic solar cells (OSCs) for two distinctly different nanostructures, by comparing the charge carrier dynamics for bilayer- and bulk-heterojunction OSCs. Most interestingly, both architectures exhibit fairly similar power conversion efficiencies (PCEs), reflecting a comparable critical domain size for charge generation and charge recombination. Although this is, at first hand, surprising, a detailed analysis points out the similarity between these two concepts. A bulk-heterojunction architecture arranges the charge generating domains in a 3D ensemble across the whole bulk, while bilayer architectures arrange the specific domains on top of each other, rather than sharp bilayers. Specifically, for the polymer PBDB-T-2F, we find that the enhanced charge generation in a bulk composite is partially compensated by reduced recombination in the bilayer architecture, when nonfullerene acceptors (NFAs) are used instead of a fullerene acceptor. Overall, we demonstrate that bilayer-heterojunction OSCs with NFAs can reach competitive PCEs compared to the corresponding bulk-heterojunction OSCs because of reduced nonradiative open-circuit voltage losses, and suppressed trap-assisted recombination, as a result of a vertically separated donor-to-acceptor nanostructure. In contrast, the bilayer-heterojunction OSCs with the fullerene acceptor exhibited poor photovoltaic characteristics compared to the corresponding bulk devices because of highly aggregated acceptor molecules on top of the polymer donor. Although free carrier generation is reduced in a in a bilayer-heterojunction, because of reduced donor/acceptor interfaces and a limited exciton diffusion length, more favorable transport pathways for unipolar charge collection can partially compensate the aforementioned disadvantages. We propose that the unique properties of NFAs may open a technical venue for the bilayer-heterojunction as a great and easy alternative to the bulk heterojunction.