Trapping of proteins under physiological conditions in a nanopipette

Operando Scanning Electrochemical Probe Microscopy during Electrocatalysis

Scanning electrochemical probe microscopy (SEPM) techniques can disclose the local electrochemical reactivity of interfaces in single-entity and sub-entity studies. Operando SEPM measurements consist of using a SEPM tip to investigate the performance of electrocatalysts, while the reactivity of the interface is simultaneously modulated. This powerful combination can correlate electrochemical activity with changes in surface properties, e.g., topography and structure, as well as provide insight into reaction mechanisms. The focus of this review is to reveal the recent progress in local SEPM measurements of the catalytic activity of a surface toward the reduction and evolution of O₂ and H₂ and electrochemical conversion of CO₂. The capabilities of SEPMs are showcased, and the possibility of coupling other techniques to SEPMs is presented. Emphasis is given to scanning electrochemical microscopy (SECM), scanning ion conductance microscopy (SICM), electrochemical scanning tunneling microscopy (EC-STM), and scanning electrochemical cell microscopy (SECCM).

Protein Dielectrophoresis: A Tale of Two Clausius–Mossottis or Something Else?

Standard DEP theory, based on the Clausius–Mossotti (CM) factor derived from solving the boundary-value problem of macroscopic electrostatics, fails to describe the dielectrophoresis (DEP) data obtained for 22 different globular proteins over the past three decades. The calculated DEP force appears far too small to overcome the dispersive forces associated with Brownian motion. An empirical theory, employing the equivalent of a molecular version of the macroscopic CM-factor, predicts a protein’s DEP response from the magnitude of the dielectric β-dispersion produced by its relaxing permanent dipole moment. A new theory, supported by molecular dynamics simulations, replaces the macroscopic boundary-value problem with calculation of the cross-correlation between the protein and water dipoles of its hydration shell. The empirical and formal theory predicts a positive DEP response for protein molecules up to MHz frequencies, a result consistently reported by electrode-based (eDEP) experiments. However, insulator-based (iDEP) experiments have reported negative DEP responses. This could result from crystallization or aggregation of the proteins (for which standard DEP theory predicts negative DEP) or the dominating influences of electrothermal and other electrokinetic (some non-linear) forces now being considered in iDEP theory.

Visualization of Ion Fluxes in Nanopipettes: Detection and Analysis of Electro-osmosis of the Second Kind

Nanopipettes are finding increasing use as nano "test tubes", with reactions triggered through application of an electrochemical potential between electrodes in the nanopipette and a bathing solution (bath). Key to this application is an understanding of how the applied potential induces mixing of the reagents from the nanopipette and the bath. Here, we demonstrate a laser scanning confocal microscope (LSCM) approach to tracking the ingress of dye into a nanopipette (20-50 nm diameter end opening). We examine the case of dianionic fluorescein under alkaline conditions (pH 11) and large applied tip potentials (±10 V), with respect to the bath, and surprisingly find that dye ingress from the bath into the nanopipette is not observed under either sign of potential. Finite element method (FEM) simulations indicate this is due to the dominance of electro-osmosis in mass transport, with electro-osmotic flow in the conventional direction at +10 V and electro-osmosis of the second kind acting in the same direction at -10 V, caused by the formation of significant space charge in the center of the orifice. The results highlight the significant deviation in mass transport behavior that emerges at the nanoscale and the utility of the combined LSCM and FEM approach in deepening understanding, which in turn should promote new applications of nanopipettes.

The latest advances on nonlinear insulator-based electrokinetic microsystems under direct current and low-frequency alternating current fields: a review

This review article presents an overview of the evolution of the field of insulator-based dielectrophoresis (iDEP); in particular, it focuses on insulator-based electrokinetic (iEK) systems stimulated with direct current and low-frequency(< 1 kHz) AC electric fields. The article covers the surge of iDEP as a research field where many different device designs were developed, from microchannels with arrays of insulating posts to devices with curved walls and nano- and micropipettes. All of these systems allowed for the manipulation and separation of a wide array of particles, ranging from macromolecules to microorganisms, including clinical and biomedical applications. Recent experimental reports, supported by important theoretical studies in the field of physics and colloids, brought attention to the effects of electrophoresis of the second kind in these systems. These recent findings suggest that DEP is not the main force behind particle trapping, as it was believed for the last two decades. This new research suggests that particle trapping, under DC and low-frequency AC potentials, mainly results from a balance between electroosmotic and electrophoretic effects (linear and nonlinear); although DEP is present in these systems, it is not a dominant force. Considering these recent studies, it is proposed to rename this field from DC-iDEP to DC-iEK (and low-frequency AC-iDEP to low-frequency AC-iEK). Whereas much research is still needed, this is an exciting time in the field of microscale EK systems, as these new findings seem to explain the challenges with modeling particle migration and trapping in iEK devices, and provide perhaps a better understanding of the mechanisms behind particle trapping.

Solvent-mediated forces in protein dielectrophoresis

DEP is an established method to manipulate micrometer-sized particles, but standard continuum theories predict only negligible effects for nanometer-sized proteins despite contrary experimental evidence. A theoretical description of protein DEP needs to consider details on the molecular scale. Previous work toward this goal addressed the role of orientational polarization of static protein dipole moments for dielectrophoretic effects, which successfully predicts the general magnitude of dielectrophoretic forces on proteins but does not readily explain negative DEP forces observed for proteins in some experiments. However, contributions to the protein chemical potential due to protein-water interactions have not yet been considered in this context. Here, we utilize atomistic molecular dynamics simulations to evaluate polarization-induced changes in the protein solvation free energy, which result in a solvent-mediated contribution to dielectrophoretic forces. We quantify solvent-mediated dielectrophoretic forces for two proteins and a small peptide in water, which follow expectations for protein-water dipole-dipole interactions. The magnitude of solvent-mediated dielectrophoretic forces exceeds predictions of nonmolecular continuum theories, but plays a minor role for the total dielectrophoretic force for the simulated proteins due to dominant contributions from the orientational polarization of their static protein dipoles. However, we extrapolate that solvent-mediated contributions to negative protein DEP forces will become increasingly relevant for multidomain proteins, complexes and aggregates with large protein-water interfaces, as well as for high electric field frequencies, which provides a potential mechanism for corresponding experimental observations of negative protein DEP.

One-dimensional assembly of β-form anhydrous guanine microrods

Biogenic guanine crystals exhibit excellent optical properties owing to their extremely high refractive index. However, there is no report related to the highly-ordered guanine assemblies in the synthetic systems. Herein, β-phase anhydrous guanine (β-AG) microrods were formed in mixed solvents of formamide and water in the presence of small organic molecules such as uric acid, pyrrole (Py), N-methyl-2-pyrrolidone (NMP), N-vinyl-2-pyrrolidone (NVP). The one-dimensional (1D) assembly of β-AG microrods form spontaneously in water, which is the first reported highly ordered 1D assembly of organic micro- or nanocrystals in the solution. The obtained β-AG microrods obtained in Py system can form reversible 1D assembly in water after being treated in organic solvents such as ethanol, acetone and isopropanol, which have high solubility in water. However, no reversible 1D assembly but only dispersed or aggregated guanine microrods formed in water after similar treatment in the other three organic solvents such as n-hexane, dichloroethane and petroleum ether with low solubility in water. Similar reversible assembly features can also be observed in other three systems, standard system, and NVP and NMP systems. The reversible 1D assemblies of guanine microrods in water and organic solvents with high solubility in water indicate that there is a strong interaction between the (100) planes of β-AG microrods in water. The oriented 1D assembly of guanine microrods with long axes perpendicular to the horizontal magnetic field can form in water under magnetic field.

Insulator Based Dielectrophoresis: Micro, Nano, and Molecular Scale Biological Applications

Insulator based dielectrophoresis (iDEP) is becoming increasingly important in emerging biomolecular applications, including particle purification, fractionation, and separation. Compared to conventional electrode-based dielectrophoresis (eDEP) techniques, iDEP has been demonstrated to have a higher degree of selectivity of biological samples while also being less biologically intrusive. Over the past two decades, substantial technological advances have been made, enabling iDEP to be applied from micro, to nano and molecular scales. Soft particles, including cell organelles, viruses, proteins, and nucleic acids, have been manipulated using iDEP, enabling the exploration of subnanometer biological interactions. Recent investigations using this technique have demonstrated a wide range of applications, including biomarker screening, protein folding analysis, and molecular sensing. Here, we review current state-of-art research on iDEP systems and highlight potential future work.

Sensing with Nanopores and Aptamers: A Way Forward

In the 90s, the development of a novel single molecule technique based on nanopore sensing emerged. Preliminary improvements were based on the molecular or biological engineering of protein nanopores along with the use of nanotechnologies developed in the context of microelectronics. Since the last decade, the convergence between those two worlds has allowed for biomimetic approaches. In this respect, the combination of nanopores with aptamers, single-stranded oligonucleotides specifically selected towards molecular or cellular targets from an in vitro method, gained a lot of interest with potential applications for the single molecule detection and recognition in various domains like health, environment or security. The recent developments performed by combining nanopores and aptamers are highlighted in this review and some perspectives are drawn.

Dielectrophoresis of proteins: experimental data and evolving theory

The ability to selectively move and trap proteins is core to their effective use as building blocks and for their characterization. Analytical and preparative strategies for proteins have been pursued and modeled for nearly a hundred years, with great advances and success. Core to all of these studies is the separation, isolation, purification, and concentration of pure homogeneous fractions of a specific protein in solution. Processes to accomplish this useful solution include biphasic equilibrium (chromatographies, extractions), mechanical, bulk property, chemical equilibria, and molecular recognition. Ultimately, the goal of all of these is to physically remove all non-like protein molecules-to the finest detail: all atoms in the full three-dimensional structure being identical down the chemical bond and bulk structure chirality. One strategy which has not been effectively pursued is exploiting the higher order subtle electrical properties of the protein-solvent system. The advent of microfluidic systems has enabled the use of very high electric fields and well-defined gradients such that extremely high resolution separations of protein mixtures are possible. These advances and recognition of these capabilities have caused a re-evaluation of the underlying theoretical models and they were found to be inadequate. New theoretical descriptions are being considered which align more closely to the total forces present and the subtlety of differences between similar proteins. These are focused on the interfacial area between the protein and hydrating solvent molecules, as opposed to the macroscale assumptions of homogeneous solutions and particles. This critical review examines all data which has been published that place proteins in electric field gradients which induce collection of those proteins, demonstrating a force greater than dispersive effects or countering forces. Evolving theoretical constructs are presented and discussed, and a general estimate of future capabilities using the higher order effects and the high fields and precise gradients of microfluidic systems is discussed. Graphical abstract.

Protein Dielectrophoresis: I. Status of Experiments and an Empirical Theory

The dielectrophoresis (DEP) data reported in the literature since 1994 for 22 different globular proteins is examined in detail. Apart from three cases, all of the reported protein DEP experiments employed a gradient field factor ∇Em2 that is much smaller (in some instances by many orders of magnitude) than the ~4 1021 V2/m3 required, according to current DEP theory, to overcome the dispersive forces associated with Brownian motion. This failing results from the macroscopic Clausius-Mossotti (CM) factor being restricted to the range 1.0 > CM > -0.5. Current DEP theory precludes the protein's permanent dipole moment (rather than the induced moment) from contributing to the DEP force. Based on the magnitude of the β-dispersion exhibited by globular proteins in the frequency range 1 kHz-50 MHz, an empirically derived molecular version of CM is obtained. This factor varies greatly in magnitude from protein to protein (e.g., ~37,000 for carboxypeptidase; ~190 for phospholipase) and when incorporated into the basic expression for the DEP force brings most of the reported protein DEP above the minimum required to overcome dispersive Brownian thermal effects. We believe this empirically-derived finding validates the theories currently being advanced by Matyushov and co-workers.

Selective Manipulation of Biomolecules with Insulator-Based Dielectrophoretic Tweezers

Insulator-based dielectrophoretic (iDEP) trapping, separating, and concentrating nanoscale objects is carried out using a non-metal, unbiased, mobile tip acing as a tweezers. The spatial control and manipulation of fluorescently-labeled polystyrene particles and DNA were performed to demonstrate the feasibility of the iDEP tweezers. Frequency-dependent iDEP tweezers' strength and polarity were quantitatively determined using two theoretical approaches to DNA, which resulted in a factor of 2 ~ 40 differences between them. In either approach, the strength of iDEP was at least 4-order of magnitude stronger than the thermal force, indicating iDEP was a dominant force for trapping, holding, and separating DNA. The trapping strength and volume of the iDEP tweezers were also determined, which further supports direct capture and manipulation of DNA at the tip end.

On the recent developments of insulator-based dielectrophoresis: A review

Insulator-based dielectrophoresis (iDEP), also known as electrodeless DEP, has become a well-known dielectrophoretic technique, no longer viewed as a new methodology. Significant advances on iDEP have been reported during the last 15 years. This review article aims to summarize some of the most important findings on iDEP organized by the type of dielectrophoretic mode: streaming and trapping iDEP. The former is primarily used for particle sorting, while the latter has great capability for particle enrichment. The characteristics of a wide array of devices are discussed for each type of dielectrophoretic mode in order to present an overview of the distinct designs and applications developed with iDEP. A short section on Joule heating effects and electrothermal flow is also included to highlight some of the challenges in the utilization of iDEP systems. The significant progress on iDEP illustrates its potential for a large number of applications, ranging from bioanalysis to clinical and biomedical assessments. The present article discusses the work on iDEP by numerous research groups around the world, with the aim of proving the reader with an overview of the state-of-the-art in iDEP microfluidic systems.

Fabrication and Use of Nanopipettes in Chemical Analysis

This review summarizes progress in the fabrication, modification, characterization, and applications of nanopipettes since 2010. A brief history of nanopipettes is introduced, and the details of fabrication, modification, and characterization of nanopipettes are provided. Applications of nanopipettes in chemical analysis are the focus in several cases, including recent progress in imaging; in the study of single molecules, single nanoparticles, and single cells; in fundamental investigations of charge transfer (ion and electron) reactions at liquid/liquid interfaces; and as hyphenated techniques combined with other methods to study the mechanisms of complicated electrochemical reactions and to conduct bioanalysis.

Nanopipettes as Monitoring Probes for the Single Living Cell: State of the Art and Future Directions in Molecular Biology

Examining the behavior of a single cell within its natural environment is valuable for understanding both the biological processes that control the function of cells and how injury or disease lead to pathological change of their function. Single-cell analysis can reveal information regarding the causes of genetic changes, and it can contribute to studies on the molecular basis of cell transformation and proliferation. By contrast, whole tissue biopsies can only yield information on a statistical average of several processes occurring in a population of different cells. Electrowetting within a nanopipette provides a nanobiopsy platform for the extraction of cellular material from single living cells. Additionally, functionalized nanopipette sensing probes can differentiate analytes based on their size, shape or charge density, making the technology uniquely suited to sensing changes in single-cell dynamics. In this review, we highlight the potential of nanopipette technology as a non-destructive analytical tool to monitor single living cells, with particular attention to integration into applications in molecular biology.

A low voltage nanopipette dielectrophoretic device for rapid entrapment of nanoparticles and exosomes extracted from plasma of healthy donors

An insulator-based dielectrophoresis (iDEP) is a label-free method that has been extensively utilized for manipulation of nanoparticles, cells, and biomolecules. Here, we present a new iDEP approach that can rapidly trap nanoparticles at the close proximity of a glass nanopipette’s tip by applying 10 V/cm direct current (DC) across the pipette’s length. The trapping mechanism was systemically studied using both numerical modeling and experimental observations. The results showed that the particle trapping was determined to be controlled by three dominant electrokinetic forces including dielectrophoretic, electrophoretic and electroosmotic force. Furthermore, the effect of the ionic strength, the pipette’s geometry, and the applied electric field on the entrapment efficiency was investigated. To show the application of our device in biomedical sciences, we demonstrated the successful entrapment of fluorescently tagged liposomes and unlabeled plasma-driven exosomes from the PBS solution. Also, to illustrate the selective entrapment capability of our device, 100 nm liposomes were extracted from the PBS solution containing 500 nm polystyrene particles at the tip of the pipette as the voltage polarity was reversed.

Dielectrophoresis-Based Protein Enrichment for a Highly Sensitive Immunoassay Using Ag/SiO2 Nanorod Arrays

A nanoscale insulator-based dielectrophoresis (iDEP) technique is developed for rapid enrichment of proteins and highly sensitive immunoassays. Dense arrays of nanorods (NDs) by oblique angle deposition create a super high electric field gradient of 2.6 × 10²⁴ V² m^-3 and the concomitant strong dielectrophoresis force successfully traps small proteins at a bias as low as 5 V. 1800-fold enrichment of bovine serum albumin protein at a remarkable rate of up to 180-fold s^-1 is achieved using oxide coated Ag nanorod arrays with pre-patterned sawtooth electrodes. Based on this system, an ultrasensitive immunoassay of mouse immunoglobulin G is demonstrated with a reduction in the limit of detection from 5.8 ng mL^-1 (37.6 pM) down to 275.3 fg mL^-1 (1.8 f M), compared with identical assays performed on glass plates. This methodology is also applied to detect a cancer biomarker prostate-specific antigen spiked in human serum with a detection limit of 2.6 ng mL^-1 . This high sensitivity results from rapid biomarker enrichment and metal enhanced fluorescence through the integration of nanostructures. The concentrated proteins also accelerate binding kinetics and enable signal saturation within 1 min. Given the easy fabrication process, this nanoscale iDEP system provides a highly sensitive detection platform for point-of-care diagnostics.

Integrated dielectrophoretic and surface plasmonic platform for million-fold improvement in the detection of fluorescent events

We present an integrated dielectrophoretic (DEP) and surface plasmonic technique to quantify ∼1 pM of fluorescent molecules in low conductivity buffers. We have established a DEP force on target molecules to bring those molecules and place them on the nanometallic structures (hotspots) for quantification through surface plasmonic effects. Our results show that the DEP is capable of placing the fluorescent molecules on the hotspots, which are depicted as a significant reduction in the fluorescence lifetime of those molecules. To efficiently integrate the DEP and plasmonic effects, we have designed and utilized pearl-shaped interdigitated electrodes (PIDEs) in experiments. These electrodes generate 2-3 times higher DEP force than traditional interdigitated electrodes. Therefore, high-throughput assays can be developed. The nanometallic structures were strategically fabricated in the periphery of PIDEs for smooth integration of DEP and plasmonic detection. With the introduction of DEP, about 10⁶-fold improvement was achieved over existing plasmonic-based detection. Therefore, this simple addition to the existing surface plasmonic-based detection will enable the disease related protein detection.

Multifunctional scanning ion conductance microscopy

Scanning ion conductance microscopy (SICM) is a nanopipette-based technique that has traditionally been used to image topography or to deliver species to an interface, particularly in a biological setting. This article highlights the recent blossoming of SICM into a technique with a much greater diversity of applications and capability that can be used either standalone, with advanced control (potential-time) functions, or in tandem with other methods. SICM can be used to elucidate functional information about interfaces, such as surface charge density or electrochemical activity (ion fluxes). Using a multi-barrel probe format, SICM-related techniques can be employed to deposit nanoscale three-dimensional structures and further functionality is realized when SICM is combined with scanning electrochemical microscopy (SECM), with simultaneous measurements from a single probe opening up considerable prospects for multifunctional imaging. SICM studies are greatly enhanced by finite-element method modelling for quantitative treatment of issues such as resolution, surface charge and (tip) geometry effects. SICM is particularly applicable to the study of living systems, notably single cells, although applications extend to materials characterization and to new methods of printing and nanofabrication. A more thorough understanding of the electrochemical principles and properties of SICM provides a foundation for significant applications of SICM in electrochemistry and interfacial science.

Interference-Free Detection of Genetic Biomarkers Using Synthetic Dipole-Facilitated Nanopore Dielectrophoresis

The motion of polarizable particles in a nonuniform electric field (i.e., dielectrophoresis) has been extensively used for concentration, separation, sorting, and transport of biological particles from cancer cells and viruses to biomolecules such as DNAs and proteins. However, current approaches to dielectrophoretic manipulation are not sensitive enough to selectively target individual molecular species. Here, we describe the application of the dielectrophoretic principle for selective detection of DNA and RNA molecules using an engineered biological nanopore. The key element of our approach is a synthetic polycationic nanocarrier that selectively binds to the target biomolecules, dramatically increasing their dielectrophoretic response to the electric field gradient generated by the nanopore. The dielectrophoretic capture of the nanocarrier-target complexes is detected as a transient blockade of the nanopore ionic current, while any nontarget nucleic acids are repelled from the nanopore by electrophoresis and thus do not interfere with the signal produced by the target's capture. Strikingly, we show that even modestly charged nanocarriers can be used to capture DNA or RNA molecules of any length or secondary structure and simultaneously detect several molecular targets. Such selective, multiplex molecular detection technology would be highly desirable for real-time analysis of complex clinical samples.

Dielectrophoretic applications for disease diagnostics using lab-on-a-chip platforms

Dielectrophoresis is a powerful technique used to distinguish distinct cellular identities in heterogeneous cell populations and to monitor changes in the cell state without the need for biochemical tags, including live and dead cells. Recent studies in the past decade have indicated that dielectrophoresis can be used to discriminate the disease state of cells by exploring the differences in the dielectric polarizabilities of the cells. Factors controlling the dielectric polarizability are dependent on the conductivity and permittivity of the cell and the suspending medium, the cell morphology, the internal structure, and the electric double layer effects associated with the charges on the cell surface. Diseased cells, such as those associated with malaria, cancer, dengue, anthrax and human African trypanosomiasis, could be spatially trapped by positive dielectrophoresis or spatially separated from other healthy cells by negative dielectrophoretic forces. The aim of this review was to provide a better and deeper understanding on how dielectrophoresis can be utilized to manipulate diseased cells. This review compiles and compares the significant findings obtained by researchers in manipulating abnormal or unhealthy cells.

Protein dielectrophoresis and the link to dielectric properties

There is a growing interest in protein dielectrophoresis (DEP) for biotechnological and pharmaceutical applications. However, the DEP behavior of proteins is still not well understood which is important for successful protein manipulation. In this paper, we elucidate the information gained in dielectric spectroscopy (DS) and electrochemical impedance spectroscopy (EIS) and how these techniques may be of importance for future protein DEP manipulation. EIS and DS can be used to determine the dielectric properties of proteins predicting their DEP behavior. Basic principles of EIS and DS are discussed and related to protein DEP through examples from previous studies. Challenges of performing DS measurements as well as potential designs to incorporate EIS and DS measurements in DEP experiments are also discussed.

Temporal and spatial temperature measurement in insulator-based dielectrophoretic devices

Insulator-based dielectrophoresis is a relatively new analytical technique with a large potential for a number of applications, such as sorting, separation, purification, fractionation, and preconcentration. The application of insulator-based dielectrophoresis (iDEP) for biological samples, however, requires the precise control of the microenvironment with temporal and spatial resolution. Temperature variations during an iDEP experiment are a critical aspect in iDEP since Joule heating could lead to various detrimental effects hampering reproducibility. Additionally, Joule heating can potentially induce thermal flow and more importantly can degrade biomolecules and other biological species. Here, we investigate temperature variations in iDEP devices experimentally employing the thermosensitive dye Rhodamin B (RhB) and compare the measured results with numerical simulations. We performed the temperature measurement experiments at a relevant buffer conductivity range commonly used for iDEP applications under applied electric potentials. To this aim, we employed an in-channel measurement method and an alternative method employing a thin film located slightly below the iDEP channel. We found that the temperature does not deviate significantly from room temperature at 100 μS/cm up to 3000 V applied such as in protein iDEP experiments. At a conductivity of 300 μS/cm, such as previously used for mitochondria iDEP experiments at 3000 V, the temperature never exceeds 34 °C. This observation suggests that temperature effects for iDEP of proteins and mitochondria under these conditions are marginal. However, at larger conductivities (1 mS/cm) and only at 3000 V applied, temperature increases were significant, reaching a regime in which degradation is likely to occur. Moreover, the thin layer method resulted in lower temperature enhancement which was also confirmed with numerical simulations. We thus conclude that the thin film method is preferable providing closer agreement with numerical simulations and further since it does not depend on the iDEP channel material. Overall, our study provides a thorough comparison of two experimental techniques for direct temperature measurement, which can be adapted to a variety of iDEP applications in the future. The good agreement between simulation and experiment will also allow one to assess temperature variations for iDEP devices prior to experiments.

Integrated sorting, concentration and real time PCR based detection system for sensitive detection of microorganisms

The extremely low limit of detection (LOD) posed by global food and water safety standards necessitates the need to perform a rapid process of integrated detection with high specificity, sensitivity and repeatability. The work reported in this article shows a microchip platform which carries out an ensemble of protocols which are otherwise carried in a molecular biology laboratory to achieve the global safety standards. The various steps in the microchip include pre-concentration of specific microorganisms from samples and a highly specific real time molecular identification utilizing a q-PCR process. The microchip process utilizes a high sensitivity antibody based recognition and an electric field mediated capture enabling an overall low LOD. The whole process of counting, sorting and molecular identification is performed in less than 4 hours for highly dilute samples.

Microarray dot electrodes utilizing dielectrophoresis for cell characterization

During the last three decades; dielectrophoresis (DEP) has become a vital tool for cell manipulation and characterization due to its non-invasiveness. It is very useful in the trend towards point-of-care systems. Currently, most efforts are focused on using DEP in biomedical applications, such as the spatial manipulation of cells, the selective separation or enrichment of target cells, high-throughput molecular screening, biosensors and immunoassays. A significant amount of research on DEP has produced a wide range of microelectrode configurations. In this paper; we describe the microarray dot electrode, a promising electrode geometry to characterize and manipulate cells via DEP. The advantages offered by this type of microelectrode are also reviewed. The protocol for fabricating planar microelectrodes using photolithography is documented to demonstrate the fast and cost-effective fabrication process. Additionally; different state-of-the-art Lab-on-a-Chip (LOC) devices that have been proposed for DEP applications in the literature are reviewed. We also present our recently designed LOC device, which uses an improved microarray dot electrode configuration to address the challenges facing other devices. This type of LOC system has the capability to boost the implementation of DEP technology in practical settings such as clinical cell sorting, infection diagnosis, and enrichment of particle populations for drug development.

Direct current dielectrophoretic simulation of proteins using an array of circular insulating posts

This paper presents a mathematical model for the manipulation of proteins using insulator-based dielectrophoresis (iDEP) and direct current (DC) electric fields. Simulations via COMSOL v4.1 Multiphysics software are implemented to study the response of moderately sized proteins on a lab-on-a-chip platform. The geometry of the device is incorporated in a model that solves current and mass conservation equations within an array of circular insulating silicon posts embedded in a channel. Both micro- and nano-scale geometries are utilized to investigate the protein concentration distributions in the iDEP device. Our results indicate that the trapping of proteins is independent of the scale with respect to the geometry of a device as long as the applied electric field remains constant. DC voltage dependency on concentration distributions has also been explored in both micro- and nano-scale device geometries. To achieve DEP trapping of the proteins, nano-scale geometry is a better selection, as the voltage necessary to generate the required electric field (2.5 MV/cm) is 10(5) × lower compared with the voltage required to generate the same field in the micro-scale device.

Nanomechanics of molecules and living cells with scanning ion conductance microscopy

Hydrodynamic flow through a nanopipet in a scanning ion conductance microscope (SICM) can exert localized forces on a sample surface. These forces can be used for trapping of molecules in lipid bilayers and for mapping the mechanical properties of living cells.

Nano-electromanipulation of spin crossover nanorods: towards switchable nanoelectronic devices

The nanoscale manipulation and charge transport properties of the [Fe(Htrz)2(trz)](BF4) spin-crossover compound is demonstrated. Such 1D spin-crossover nanostructures are attractive building blocks for nanoelectronic switching and memory devices.

Characterization of microparticle separation utilizing electrokinesis within an electrodeless dielectrophoresis chip

This study demonstrated the feasibility of utilizing electrokinesis in an electrodeless dielectrophoresis chip to separate and concentrate microparticles such as biosamples. Numerical simulations and experimental observations were facilitated to investigate the phenomena of electrokinetics, i.e., electroosmosis, dielectrophoresis, and electrothermosis. Moreover, the proposed operating mode can be used to simultaneously convey microparticles through a microfluidic device by using electroosmotic flow, eliminating the need for an additional micropump. These results not only revealed that the directions of fluids could be controlled with a forward/backward electroosmotic flow but also categorized the optimum separating parameters for various microparticle sizes (0.5, 1.0 and 2.0 μm). Separation of microparticles can be achieved by tuning driving frequencies at a specific electric potential (90 Vpp·cm⁻¹). Certainly, the device can be designed as a single automated device that carries out multiple functions such as transportation, separation, and detection for the realization of the envisioned Lab-on-a-Chip idea.

Dielectrophoresis force spectroscopy for colloidal clusters

Optical trapping-based force spectroscopy was used to measure the frequency-dependent DEP forces and DEP crossover frequencies of colloidal polymethyl methacrylate spheres and clusters. A single sphere or cluster, held by an optical tweezer, was positioned near the center of a pair of gold-film electrodes where alternating current elecroosmosis flow was negligible. Use of amplitude modulation and phase-sensitive lock-in detection for accurate measurement of the DEP force yielded new insight into dielectric relaxation mechanisms near the crossover frequencies. On one hand, the size dependence of the DEP force near the crossover frequencies indicates that the dominant polarization mechanism is a volume effect. On the other hand, the power-law dependence of the crossover frequency on the particle radius with an exponent of -2 indicates the dielectric relaxation is more likely because of ionic diffusion across the particle surface, suggesting the dominant polarization mechanism may be a surface polarization effect. Better theories are needed to explain the experiment. Nevertheless, the strong size dependence of the crossover frequencies suggests the use of DEP for size sorting of micron-sized particles.

Scanning ion conductance microscopy for studying biological samples

Scanning ion conductance microscopy (SICM) is a scanning probe technique that utilizes the increase in access resistance that occurs if an electrolyte filled glass micro-pipette is approached towards a poorly conducting surface. Since an increase in resistance can be monitored before the physical contact between scanning probe tip and sample, this technique is particularly useful to investigate the topography of delicate samples such as living cells. SICM has shown its potential in various applications such as high resolution and long-time imaging of living cells or the determination of local changes in cellular volume. Furthermore, SICM has been combined with various techniques such as fluorescence microscopy or patch clamping to reveal localized information about proteins or protein functions. This review details the various advantages and pitfalls of SICM and provides an overview of the recent developments and applications of SICM in biological imaging. Furthermore, we show that in principle, a combination of SICM and ion selective micro-electrodes enables one to monitor the local ion activity surrounding a living cell.

Transitioning Streaming to Trapping in DC Insulator-based Dielectrophoresis for Biomolecules

Exploiting dielectrophoresis (DEP) to concentrate and separate biomolecules has recently shown large potential as a microscale bioanalytical tool. Such efforts however require tailored devices and knowledge of all interplaying transport mechanisms competing with dielectrophoresis (DEP). Specifically, a strong DEP contribution to the overall transport mechanism is necessary to exploit DEP of biomolecules for analytical applications such as separation and fractionation. Here, we present improved microfluidic devices combining optical lithography and focused ion beam milling (FIBM) for the manipulation of DNA and proteins using insulator-based dielectrophoresis (iDEP) and direct current (DC) electric fields. Experiments were performed on an elastomer platform forming the iDEP microfluidic device with integrated nanoposts and nanopost arrays. Microscale and nanoscale iDEP was studied for λ-DNA (48.5 kbp) and the protein bovine serum albumin (BSA). Numerical simulations were adapted to the various tested geometries revealing excellent qualitative agreement with experimental observations for streaming and trapping DEP. Both the experimental and simulation results indicate that DC iDEP trapping for λ-DNA occurs with tailored nanoposts fabricated via FIBM. Moreover, streaming iDEP concentration of BSA is improved with integrated nanopost arrays by a factor of 45 compared to microfabricated arrays.

Hydrodynamic trapping of molecules in lipid bilayers

In this work we show how hydrodynamic forces can be used to locally trap molecules in a supported lipid bilayer (SLB). The method uses the hydrodynamic drag forces arising from a flow through a conical pipette with a tip radius of 1-1.5 μm, placed approximately 1 μm above the investigated SLB. This results in a localized forcefield that acts on molecules protruding from the SLB, yielding a hydrodynamic trap with a size approximately given by the size of the pipette tip. We demonstrate this concept by trapping the protein streptavidin, bound to biotin receptors in the SLB. It is also shown how static and kinetic information about the intermolecular interactions in the lipid bilayer can be obtained by relating how the magnitude of the hydrodynamic forces affects the accumulation of protein molecules in the trap.

Detection of Cryptosporidium in miniaturised fluidic devices

Contamination of drinking water with the protozoan pathogen, Cryptosporidium, represents a serious risk to human health due to the low infectious dose and the resistance of this parasite to chlorine disinfection. Therefore, several countries have legislated for the frequent monitoring of drinking water for Cryptosporidium presence. Existing approved monitoring protocols are however time-consuming and do not provide essential information on the species, virulence or viability of detected oocysts. Rapid, more information-rich and automatable systems for Cryptosporidium detection are highly sought-after, and numerous miniaturised devices have been developed to address this need. This review article aims to summarise the state-of-the-art and compare the performance of these systems in terms of detection limit, ability to determine species, viability and performance in the presence of interferents. Finally, conclusions are drawn with regard to the most promising methods and directions of future research.

Scanning ion conductance microscopy

Scanning ion conductance microscopy (SICM) is a versatile type of scanning probe microscopy for studies in molecular biology and materials science. Recent advances in feedback and probe fabrication have greatly increased the resolution, stability, and speed of imaging. Noncontact imaging and the ability to deliver materials to localized areas have made SICM especially fruitful for studies of molecular biology, and many examples of such use have been reported. In this review, we highlight new developments in the operation of SICM and describe some of the most exciting recent studies from this growing field.