Amphiphilic Graphene Composites

Assembling phenyl-modified colloidal silica on graphene oxide towards ethanol redispersible graphene oxide powder

Recently, ethanol has shown promising potential in the large-scale reduction of graphene oxide (GO) into graphene. However, dispersion of GO powder in ethanol is a challenge due to its poor affinity, which hinders permeation and intercalation of ethanol between GO molecule layers. In this paper, phenyl-modified colloidal silica nanospheres (PSNS) were synthesized by phenyl-tri-ethoxy-silane (PTES) and tetra-ethyl ortho-silicate (TEOS) using a sol-gel method. PSNS was then assembled onto a GO surface to form a PSNS@GO structure by possible non-covalent π-π stacking interactions between the phenyl groups and GO molecules. The surface morphology, chemical composition, and dispersion stability were analyzed by scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetry, Raman spectroscopy, X-ray diffractometry, nuclear magnetic resonance, and particle sedimentation test. The results showed that the as-assembled PSNS@GO suspension had excellent dispersion stability with an optimal PSNS concentration of 5 vol% PTES. With the optimized PSNS@GO, ethanol can permeate between the GO layers and intercalate along with PSNS particles via formation of hydrogen bonds between assembled PSNS on GO and ethanol, achieving a stable dispersion of GO in ethanol. The optimized PSNS@GO powder remained redispersible after drying and milling according to this interaction mechanism which is favorable for large scale reduction processes. Higher PTES concentration may result in agglomeration of PSNS and formation of wrapping structures of PSNS@GO after drying and worsen its dispersion capability.

A Malleable Composite Dough with Well-Dispersed and High-Content Boron Nitride Nanosheets

Aggregation of two-dimensional (2D) nanosheet fillers in a polymer matrix is a prevalent problem when the filler loading is high, leading to degradation of physical and mechanical properties of the composite. To avoid aggregation, a low-weight fraction of the 2D material (<5 wt %) is usually used to fabricate the composite, limiting performance improvement. Here, we develop a mechanical interlocking strategy where well-dispersed high filling content (up to 20 wt %) of boron nitride nanosheets (BNNSs) can be incorporated into a polytetrafluoroethylene (PTFE) matrix, resulting in a malleable, easy-to-process and reusable BNNS/PTFE composite dough. Importantly, the well-dispersed BNNS fillers can be rearranged into a highly oriented direction due to the malleable nature of the dough. The resultant composite film has a high thermal conductivity (4408% increase), low dielectric constant/loss, and excellent mechanical properties (334%, 69%, 266%, and 302% increases for tensile modulus, strength, toughness, and elongation, respectively), making it suitable for thermal management applications in the high-frequency areas. The technique is useful for the large-scale production of other 2D material/polymer composites with a high filler content for different applications.

BODIPY-GO nanocomposites decorated with a biocompatible branched ethylene glycol moiety for targeted PDT

The properties of graphene oxide (GO) have received much attention and been applied to the exploration of potential applications in disease-related diagnostics and non-invasive therapy. One application, photodynamic therapy (PDT), involves the killing of cancer cells where singlet oxygen is generated with light irradiation of the appropriate wavelength. In this work, three new BODIPY derivatives (13-15), decorated with carbohydrate moieties for active targeting and branched ethylene glycol for biocompatibility, and their GO based nanocarriers were designed to study the singlet oxygen production and PDT efficiency. First, BODIPYs were prepared, followed by the fabrication of GO layers with BODIPY dyes via a non-covalent method. Detailed characterizations of the materials were carried out with mass spectrometry, FT-IR spectroscopy, ¹H NMR, ¹³C NMR, elemental analysis, Raman spectroscopies, EDX analysis and TEM and AFM microscopies. The efficiency of singlet oxygen generation in organic and water-based solutions was determined by photobleaching with 1,3-diphenylisobenzofuran (DPBF) and 9,10-anthracenediyl-bis(methylene)dimalonic acid (ABDA), respectively. The results in in vitro PDT analysis against K562 human cancer cells indicate the prepared materials are highly promising in PDT anticancer therapy and the IC₅₀ values of GO loaded BODIPY derivatives bearing heavy atoms, GO-14 and GO-15, were calculated as 40.59 nM and 39.21 nM, respectively.

Facile preparation of covalently functionalized graphene with 2,4-dinitrophenylhydrazine and investigation of its characteristics

This article reports a fast and easy method for simultaneously in situ reducing and functionalizing graphene oxide. 2,4-Dinitrophenylhydrazine hydrate salt molecules are reduced by graphene oxide by reacting with oxide groups on the surface and removing these groups, and 2,4-dinitrophenylhydrazone groups are replaced with oxide groups. The synthesized materials have been investigated using Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), and UV absorption. Also, the morphology has been examined with a scanning electron microscope (SEM) and Brunauer-Emmett-Teller (BET) analysis. The result of the photocurrent response and electrochemical behavior of the samples through cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy (EIS) have been analyzed to investigate the effect of physical and chemical changes compared to graphene.

Evolution of graphene oxide (GO)-based nanohybrid materials with diverse compositions: an overview

The discovery of the 2D nanostructure of graphene was in fact the beginning of a new generation of materials. Graphene itself, its oxidized form graphene oxide (GO), the reduced form of GO (RGO) and their numerous composites are associates of this generation. Out of this spectrum of materials, the development of GO and related hybrid materials has been reviewed in the present article. GO can be functionalized with metals (Ag and Mg) and metal oxides (CuO, MgO, Fe₂O₃, Ag₂O, etc.) nanoparticles (NPs), organic ligands (chitosan and EDTA) and can also be dispersed in different polymeric matrices (PVA, PMMA, PPy, and PAn). All these combinations give rise to nanohybrid materials with improved functionality. An updated report on the chronological development of such nanohybrid materials of diverse nature has been delivered in the present context. Modifications in synthesis methodologies as well as performances and applications of individual materials are addressed accordingly. The functional properties of GO were synergistically modified by photoactive semiconductor NPs; as a result, the GO–MO hybrids acquired excellent photocatalytic ability and were able to degrade a large variety of organic dyes (MB, RhB, MO, MR, etc.) and pathogens. The large surface area of GO was successfully complemented by the NPs so that high and selective adsorption capacity towards metal ions and organic molecules as well as improved charge separation properties could be achieved. As a result, GO–MO hybrids have been considered effective materials in water purification, energy storage and antibacterial applications. GO–MO hybrids with magnetic particles have exhibited selective destruction of cancerous cells and controlled drug release properties, extremely important in the pharmaceutical field. Chitosan and EDTA-modified GO could form 3D network-like structures with strong efficiency in removing heavy metal ions and organic pollutants. GO as a filler enhanced the strength, flexibility and functional properties of common polymers, such as PVA and PVC, to a large extent while, GO–CP composites with polyaniline and polypyrrole are considered suitable for the fabrication of biosensors, supercapacitors, and MEMS as well as efficient photothermal therapy agents. In summary, GO-based hybrids with inorganic and organic counterparts have been designed, the unique properties of which are exploited in versatile fields of applications.

GO undergoes synergistic interaction with MO nanoparticles and the hybrid can be used as a heterogeneous catalyst for the photocatalytic degradation of dyes.

Interfacial Modulation of Graphene by Polythiophene with Controlled Molecular Weight to Enhance Thermal Conductivity

With a trend of continuing improvement in the development of electronic devices, a problem of serious heat accumulation has emerged which has created the need for more efficient thermal management. Graphene sheets (GNS) have drawn much attention with regard to heat transfer because of their excellent in-plane thermal conductivity; however, the ultrahigh interfacial thermal resistance between graphene lamellae has seriously restricted its practical applications. Herein, we describe heat transfer membranes composed of graphene which have been modified by intrinsic thermally conductive polymers with different molecular weights. The presence of macromolecular surface modifiers not only constructed the graphene heat transfer interface by π-π interactions, but also significantly enhanced the membranes' in-plane thermal conductivity by utilizing their intrinsic heat transfer properties. Such results indicated that the in-plane thermal conductivity of the fabricated membrane exhibits a high in-plane thermal conductivity of 4.17 W m-1 K-1, which, containing the GNS modified with 6000 g/mol (Mn) of poly(3-hexylthiophene) (P3HT), was 26 times higher that of poly (vinylidene fluoride) (PVDF). The P3HT molecular chain with specific molecular weight can form more matching structure π-π interactions, which promotes thermal conductivity. The investigation of different molecular weights has provided a new pathway for designing effective interfacial structures to relieve interface thermal resistance in thermally conductive membranes.

Graphene oxide-controlled neutral versus cationic form of a red emitting dye: enhancement of fluorescence by graphene oxide

Fluorescence enhancement of fluorophores in neat solvent media in the presence of graphene oxide (GO) is less known. It is necessary to re-examine the role of GO from the fundamental scientific viewpoint. Herein, we have reported GO controlled conversion from the neutral to cationic form of a red emitting molecule. Besides this, the switching of the role of GO as an enhancer to a quencher of fluorescence depending on the concentration of GO in the presence of proton accepting solvent media was established. Intermolecular proton transfer from the GO surface to fluorophores is responsible for this phenomenon.

Atomically Thin Materials for Next-Generation Rechargeable Batteries

Atomically thin materials (ATMs) with thicknesses in the atomic scale (typically <5 nm) offer inherent advantages of large specific surface areas, proper crystal lattice distortion, abundant surface dangling bonds, and strong in-plane chemical bonds, making them ideal 2D platforms to construct high-performance electrode materials for rechargeable metal-ion batteries, metal-sulfur batteries, and metal-air batteries. This work reviews the synthesis and electronic property tuning of state-of-the-art ATMs, including graphene and graphene derivatives (GE/GO/rGO), graphitic carbon nitride (g-C₃N₄), phosphorene, covalent organic frameworks (COFs), layered transition metal dichalcogenides (TMDs), transition metal carbides, carbonitrides, and nitrides (MXenes), transition metal oxides (TMOs), and metal-organic frameworks (MOFs) for constructing next-generation high-energy-density and high-power-density rechargeable batteries to meet the needs of the rapid developments in portable electronics, electric vehicles, and smart electricity grids. We also present our viewpoints on future challenges and opportunities of constructing efficient ATMs for next-generation rechargeable batteries.

Ultrathin Surface Coating of Nitrogen-Doped Graphene Enables Stable Zinc Anodes for Aqueous Zinc-Ion Batteries

Owing to the high volumetric capacity and low redox potential, zinc (Zn) metal is considered to be a remarkably prospective anode for aqueous Zn-ion batteries (AZIBs). However, dendrite growth severely destabilizes the electrode/electrolyte interface, and accelerates the generation of side reactions, which eventually degrade the electrochemical performance. Here, an artificial interface film of nitrogen (N)-doped graphene oxide (NGO) is one-step synthesized by a Langmuir-Blodgett method to achieve a parallel and ultrathin interface modification layer (≈120 nm) on Zn foil. The directional deposition of Zn crystal in the (002) planes is revealed because of the parallel graphene layer and beneficial zincophilic-traits of the N-doped groups. Meanwhile, through the in situ differential electrochemical mass spectrometry and in situ Raman tests, the directional plating morphology of metallic Zn at the interface effectively suppresses the hydrogen evolution reactions and passivation. Consequently, the pouch cells pairing this new anode with LiMn₂ O₄ cathode maintain exceptional energy density (164 Wh kg^-1 after 178 cycles) at a reasonable depth of discharge, 36%. This work provides an accessible synthesis method and in-depth mechanistic analysis to accelerate the application of high-specific-energy AZIBs.

Polymer-dispersed reduced graphene oxide nanosheets and Prussian blue modified biosensor for amperometric detection of sarcosine

A new disposable amperometric biosensor for sarcosine (Sar, a biomarker for prostate cancer) was designed based on screen-printed carbon electrodes, Prussian blue, polymer dispersed reduced graphene oxide (P-rGO) nanosheets, and sarcosine oxidase (SOx). Poly(sodium 4-styrenesulfonate-r-LAHEMA) denoted as PSSL was newly synthesized as dispersant for rGO. The P-rGO was utilized for SOx immobilization, the sulfonate and disulfide functionalities in PSSL enable physical adsorption of SOx and its bioactivity and stability properties were improved. The biosensor was optimized by various enzyme concentration, applied potential, and operating pH. Under the optimized conditions, the biosensor exhibited maximum current responses within 5 s at an applied potential of -0.1 V vs. integrated Ag/AgCl reference electrode. The biosensor had a dynamic linear range of 10-400 μM, with a sensitivity of 9.04 μA mM^-1 cm^-2 and a low detection limit of 0.66 μM (S/N = 3). Additionally, the biosensor possesses strong anti-interference capability, high reproducibility, and storage stability over 3 weeks. Furthermore, its clinical applicability was tested in urine samples from both prostate cancer patients and healthy control, and the analytical recoveries were satisfactory. Therefore, this biosensor has significant potential in the rapid and non-invasive point-of-care testing for prostate cancer diagnosis.

Highly enhanced nonlinear optical absorption with ultrafast charge transfer of reduced graphene oxide hybridized by an azobenzene derivative

Graphene-based materials have been attracted many attentions due to their excellent properties and potential applications in many fields. Graphene also provides a flexible substrate to develop novel functional materials by hybridizing with other organic or inorganic components. Herein, we report the functionalization of reduced graphene oxide (RGO) with an azobenzene derivative (BNB-t8) containing the π-conjugated moiety and hydrogen bonding groups, to improve the optical and nonlinear optical properties of RGO. With the introducing of BNB-t8, a new absorption band is formed and dominates the absorption spectrum, clearly demonstrates that the BNB-t8 has been hybridized with RGO, by combining the analysis of Raman and XRD data. Femtosecond Z-scan results present a highly enhanced saturable optical absorption of BNB-t8/RGO hybrid compared with that of RGO. By optimizing the hybridization ratio of BNB-t8 to RGO, the saturable absorption coefficient of BNB-t8/RGO hybrid reaches to -237 m/W, 38 times larger than that of RGO (-6.2 m/W). In the meantime, the third-order susceptibility χ⁽³⁾ of BNB-t8/RGO hybrid is aslo enhanced by 8 times to be 5.18×10^-13 esu. These enhancements of nonlinear optical properties of BNB-t8/RGO hybrid mainly arise from the charge transfer from RGO to BNB-t8. Femtosecond transient absorption measurements reveal that the charge separation takes place in 0.28 ps and the charge recombination in 2.0 ps, indicating a strong electron coupling and thus an enhanced electron delocalization in BNB-t8/RGO hybrid compared with those in RGO. We suggest that the noncovalent π-π interaction plays the dominant role for enhancing the electron delocalization of RGO after hybridizing with BNB-t8, while the hydrogen bonding interaction reinforce the coupling interaction between BNB-t8 and RGO moieties in the hybrid. The as-prepared BNB-t8/RGO hybrid with high saturable absorption coefficient with an ultrafast response presents a potential candidate as saturable absorber of mode-locked laser.

Ballistic Performance of Ramie Fabric Reinforcing Graphene Oxide-Incorporated Epoxy Matrix Composite

Graphene oxide (GO) incorporation in natural fiber composites has recently defined a novel class of materials with enhanced properties for applications, including ballistic armors. In the present work, the performance of a 0.5 vol % GO-incorporated epoxy matrix composite reinforced with 30 vol % fabric made of ramie fibers was investigated by stand-alone ballistic tests against the threat of a 0.22 lead projectile. Composite characterization was also performed by Fourier-transform infrared spectroscopy, thermal analysis and X-ray diffraction. Ballistic tests disclosed an absorbed energy of 130 J, which is higher than those reported for other natural fabrics epoxy composite, 74–97 J, as well as plain Kevlar (synthetic aramid fabric), 100 J, with the same thickness. This is attributed to the improved adhesion between the ramie fabric and the composite matrix due to the GO—incorporated epoxy. The onset of thermal degradation above 300 °C indicates a relatively higher working temperature as compared to common natural fiber polymer composites. DSC peaks show a low amount of heat absorbed or release due to glass transition endothermic (113–121 °C) and volatile release exothermic (~132 °C) events. The 1030 cm⁻¹ prominent FTIR band, associated with GO bands between epoxy chains and graphene oxide groups, suggested an effective distribution of GO throughout the composite matrix. As expected, XRD of the 30 vol % ramie fabric-reinforced GO-incorporated epoxy matrix composite confirmed the displacement of the (0 0 1) peak of GO by 8° due to intercalation of epoxy chains into the spacing between GO layers. By improving the adhesion to the ramie fabric and enhancing the thermal stability of the epoxy matrix, as well as by superior absorption energy from projectile penetration, the GO may contribute to the composite effective ballistic performance.

Hetero-structured MnO-Mn3O4@rGO composites: Synthesis and nonenzymatic detection of H2O2

The construction of metal-oxide heterojunction architecture has greatly widened applications in the fields of optoelectronics, energy conversions and electrochemical sensors. In this study, olive-like hetero-structured MnO-Mn₃O₄ microparticles wrapped by reduced graphene oxide (MnO-Mn₃O₄@rGO) were synthesized through a facile solvothermal-calcination treatment. The morphology and structure of MnO-Mn₃O₄@rGO were characterized by scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, and X-ray diffraction. The as-synthesized MnO-Mn₃O₄@rGO exhibited prominent catalyzing effect on the electroreduction of H₂O₂, due to the combination of good electrical conductivity of rGO and the synergistic effect of MnO and Mn₃O₄. The MnO-Mn₃O₄@rGO modified glassy carbon electrode provided a wide linear response from 0.004 to 17 mM, a low detection limit of 0.1 μM, and high sensitivity of 274.15 μA mM^-1 cm^-2. The proposed sensor displayed noticeable selectivity and long-term stability. In addition, the biosensor has been successfully applied for detecting H₂O₂ in tomato sauce with good recovery, revealing its promising potential applications for practical electrochemical sensors.

Toxicity Studies on Graphene-Based Nanomaterials in Aquatic Organisms: Current Understanding

Graphene and its oxide are nanomaterials considered currently to be very promising because of their great potential applications in various industries. The exceptional physiochemical properties of graphene, particularly thermal conductivity, electron mobility, high surface area, and mechanical strength, promise development of novel or enhanced technologies in industries. The diverse applications of graphene and graphene oxide (GO) include energy storage, sensors, generators, light processing, electronics, and targeted drug delivery. However, the extensive use and exposure to graphene and GO might pose a great threat to living organisms and ultimately to human health. The toxicity data of graphene and GO is still insufficient to point out its side effects to different living organisms. Their accumulation in the aquatic environment might create complex problems in aquatic food chains and aquatic habitats leading to debilitating health effects in humans. The potential toxic effects of graphene and GO are not fully understood. However, they have been reported to cause agglomeration, long-term persistence, and toxic effects penetrating cell membrane and interacting with cellular components. In this review paper, we have primarily focused on the toxic effects of graphene and GO caused on aquatic invertebrates and fish (cell line and organisms). Here, we aim to point out the current understanding and knowledge gaps of graphene and GO toxicity.

Direct Ink Writing Technology (3D Printing) of Graphene-Based Ceramic Nanocomposites: A Review

In the present work, the state of the art of the most common additive manufacturing (AM) technologies used for the manufacturing of complex shape structures of graphene-based ceramic nanocomposites, ceramic and graphene-based parts is explained. A brief overview of the AM processes for ceramic, which are grouped by the type of feedstock used in each technology, is presented. The main technical factors that affect the quality of the final product were reviewed. The AM processes used for 3D printing of graphene-based materials are described in more detail; moreover, some studies in a wide range of applications related to these AM techniques are cited. Furthermore, different feedstock formulations and their corresponding rheological behavior were explained. Additionally, the most important works about the fabrication of composites using graphene-based ceramic pastes by Direct Ink Writing (DIW) are disclosed in detail and illustrated with representative examples. Various examples of the most relevant approaches for the manufacturing of graphene-based ceramic nanocomposites by DIW are provided.

The effects of hydroxide and epoxide functional groups on the mechanical properties of graphene oxide and its failure mechanism by molecular dynamics simulations

Graphene oxide (GO) could be assembled via amphiphilic interface adhesion into nano-composites.

Graphene Modified Multifunctional Personal Protective Clothing

Personal protective clothing is intended to protect the wearer from various hazards (mechanical, biological, chemical, thermal, radiological, etc.) and inhospitable environmental conditions that may cause harm or even death. There are various types of personal protective clothing, manufactured with different materials based on hazards and end user requirements. Conventional protective clothing has impediments such as high weight, bulky nature, lack of mobility, heat stress, low heat dissipation, high physical stress, diminishing dexterity, diminishing scope of vision, lack of breathability, and reduced protection against pathogens and hazards. By virtue of the superlative properties of graphene, fabrics modified with this material can be an effective means to overcome these limitations and to improve properties such as mechanical strength, antibacterial activity, flame resistance, conductivity, and UV resistance. The limitations of conventional personal protective equipment are discussed, followed by necessary measures which might be taken to improve personal protective equipment (PPE), the unique properties of graphene, methods of graphene incorporation in fabrics, and the current research status and potential of graphene-modified performance textiles relevant to PPE.

Effect of Graphene Oxide Coating on Natural Fiber Composite for Multilayered Ballistic Armor

Composites with sustainable natural fibers are currently experiencing remarkably diversified applications, including in engineering industries, owing to their lower cost and density as well as ease in processing. Among the natural fibers, the fiber extracted from the leaves of the Amazonian curaua plant (Ananas erectifolius) is a promising strong candidate to replace synthetic fibers, such as aramid (Kevlar™), in multilayered armor system (MAS) intended for ballistic protection against level III high velocity ammunition. Another remarkable material, the graphene oxide is attracting considerable attention for its properties, especially as coating to improve the interfacial adhesion in polymer composites. Thus, the present work investigates the performance of graphene oxide coated curaua fiber (GOCF) reinforced epoxy composite, as a front ceramic MAS second layer in ballistic test against level III 7.62 mm ammunition. Not only GOCF composite with 30 vol% fibers attended the standard ballistic requirement with 27.4 ± 0.3 mm of indentation comparable performance to Kevlar™ 24 ± 7 mm with same thickness, but also remained intact, which was not the case of non-coated curaua fiber similar composite. Mechanisms of ceramic fragments capture, curaua fibrils separation, curaua fiber pullout, composite delamination, curaua fiber braking, and epoxy matrix rupture were for the first time discussed as a favorable combination in a MAS second layer to effectively dissipate the projectile impact energy.

Graphene based adsorbents for remediation of noxious pollutants from wastewater

The contamination of water resources with noxious pollutants is a serious issue. Many aquatic systems are contaminated with different toxic inorganic and organic species; coming to wastewater from various anthropogenic sources such as industries, agriculture, mining, and domestic households. Keeping in view of this, wastewater treatment appears to the main environmental challenge. Adsorption is one of the most efficient techniques for removing all most all types of pollutants i.e. inorganics and organics. Nowadays, graphene and its composite materials are gaining importance as nano adsorbents. Graphene; a two-dimensional nanomaterial having single-atom graphite layer; has attracted a great interest in many application areas (including wastewater treatment) due to its unique physico-chemical properties. The present paper is focused on the remediation of noxious wastes from wastewater using graphene based materials as adsorbents, and it contains all the details on materials - i.e., from their synthesis to application in the field of wastewater treatment (removal of hazardous contaminants of different chemical nature - heavy and rare-earth metal ions, and organic compounds - from wastewater effluents. The efficiency of the adsorption and desorption of these substances is considered. Certainly, this article will be useful for nano environmentalist to design future experiments for water treatment.

Cu(0) nanoparticle-decorated functionalized reduced graphene oxide sheets as artificial peroxidase enzymes: application for colorimetric detection of Cr(vi) ions

Graphene oxide sheets were functionalized by a “click” chemistry approach which was utilized for the decoration of Cu(0) nanoparticles for sensitive colorimetric detection of Cr(vi) ions.

Graphene oxide/nanometal composite membranes for nanofiltration: synthesis, mass transport mechanism, and applications

We reviewed the recent developments in graphene-based composite membranes and discussed their challenges in this paper.

Nano-graphene oxide-UCNP-Ce6 covalently constructed nanocomposites for NIR-mediated bioimaging and PTT/PDT combinatorial therapy

NIR light-induced imaging-guided cancer therapy is an encouraging route in the cancer theranostic field. Herein, we describe a novel nanoscale proposal, which is established by covalently implanting core-shell structured upconversion nanoparticles (UCNPs) with nanographene oxide (NGO) by a process utilizing polyethylene glycol (PEG), and consequently loading Chlorin e6 (Ce6) onto the surface of NGO. The acquired NGO-UCNP-Ce6 (NUC) nanocomposites can not only be employed as upconversion luminescence (UCL) imaging probes of cells and whole-body animals with high contrast for diagnosis, but also can generate reactive oxygen species (ROS) under 808 nm light excitation for photodynamic therapy (PDT); over and above, they can swiftly and proficiently translate the 808 nm photon into thermal energy for photothermal therapy (PTT). An extraordinarily enhanced and synchronized therapeutic effect paralleled to the individual PTT or PDT is achieved, rendering extraordinary therapeutic effectiveness for cancer treatment. Consequently, profiting from this inimitable multifunctional nanohybrid, the NUCs synthesized here are encouraging as a cohesive theranostic probe for impending UCL imaging-guided combinatorial PDT/PTT.

PAMAM Dendrimer Modified Reduced Graphene Oxide Postfunctionalized by Horseradish Peroxidase for Biosensing H2O2

In this chapter, we describe the tethering of horseradish peroxidase (HRP) to reduced graphene oxide (RGO) for sensing H₂O₂ in serum. To accomplish this, RGO was synthesized through a green route by reducing graphene oxide (GO) prepared by Hummers method with carrot extract. The RGO was then covalently functionalized by electrochemical amination using fourth generation, amine-terminated PAMAM dendrimers. Subsequently, HRP was postfunctionalized through glutaraldehyde linkage. The synthesized RGO and the functionalization steps were well characterized by spectroscopic, microscopic, and electrochemical techniques. The application of HRP tethered RGO was demonstrated for H₂O₂ sensing in blood serum. This work provides scope for extending this functionalization strategy for other carbonaceous materials as well.

Synthesis of amphiphilic graphitic silver nanoparticles with inherent internal standards: an efficient strategy for reliable quantitative SERS analysis in common fluids

An efficient strategy for reliable quantitative SERS analysis in fluids by amphiphilic functionalization of graphitic silver nanoparticles with internal standards.

Scrolling up graphene oxide nanosheets assisted by self-assembled monolayers of alkanethiols

We report a simple and novel method for the fabrication of high-quality nanoscrolls of graphene oxide (GO) and graphene oxide decorated with silver nanoparticles (GO-Ag) on a gold substrate through a scrolling process assisted by the self-assembly of alkanethiol monolayers. The yield and rate of the scrolling process were highly dependent on the lengths of the alkanethiol molecules, and could be well described by power law functions. Importantly, compared to nanosheets, nanoscrolls of GO and GO-Ag showed superior performance in humidity sensing due to their unique scrolled structures.

Fabricating fast triggered electro-active shape memory graphite/silver nanowires/epoxy resin composite from polymer template

In recent years shape-memory polymers have been under intense investigation due to their unique mechanical, thermal, and electrical properties that could potentially make them extremely valuable in numerous engineering applications. In this manuscript, we report a polymer-template-assisted assembly manufacturing strategy used to fabricate graphite/silver nanowires/epoxy resin (PGSE) composite. In the proposed method, the porous polymer foams work as the skeleton by forming three-dimensional graphite structure, whereas the silver nanowires act as the continuous conductive network. Preliminary testing on hybrid foams after vacuum infusion showed high electrical conductivity and excellent thermal stability. Furthermore, the composites were found to recover their original shape within 60 seconds from the application of a 0.8 V mm⁻¹ electric field. Notably, the reported shape-memory polymer composites are manufactured with readily-available raw materials, they are fast to manufacture, and are shape-controlled.

Exfoliation of Reduced Graphene Oxide with Self-Assembled π-Gelators for Improved Electrochemical Performance

Among several methodologies to improve the solution processing of graphene-based materials, noncovalent functionalization has been considered as the simplest and nondestructive method. Herein, we show that molecular self-assembly process can be used as a useful tool to exfoliate reduced graphene oxide (RGO), resulting in hybrid materials with improved physical properties. Upon interacting with a π-gelator, the dispersing ability of the RGO increased significantly in most of nonpolar and polar aprotic solvents when compared to the bare one. The amount of RGO dispersed was 1.7-1.8 mg mL^-1 in solvents such as toluene, o-dichlorobenzene (ODCB) and tetrahydrofuran (THF). Morphological studies revealed that aggregation of π-gelator over RGO helps to exfoliate graphene layers to remain as individual sheets with higher surface area. Experimental studies revealed enhanced surface area (250 m² g^-1) and better conductivity (3.7 S m^-1) of the hybrid materials with 30% of RGO content resulting in excellent electrochemical performance (specific capacitance of 181 F g^-1) as electrodes for supercapacitors.

Oligo(p-phenylene ethynylene) with Cyanoacrylate Terminal Groups and Graphene Composite as Fluorescent Chemical Sensor for Cysteine

A chemical sensor for cysteine (Cys) was fabricated based on a fluorescent oligo(p-phenylene ethynylene)s (OPEs) and OPE-graphene oxide (GO) composite. OPE with cyanoacrylate terminal groups were synthesized by a Pd-catalyzed Sonogashira coupling reaction and Knoevenagel condensation for use as a chemical sensor for Cys. The optical properties and Cys sensing capability of the cyanoacrylate modified OPE and OPE-GO composite were investigated. In addition of Cys, the fluorescence of OPE was blue-shifted and decreased (fluorescence turn-off), while the fluorescence of the OPE-GO composite was enhanced (fluorescence turn-on). Thus, OPE with cyanoacrylate terminal groups and OPE-GO composite acts a highly sensitive fluorescent chemical sensor for Cys.

Recent Advances in Ultrathin Two-Dimensional Nanomaterials

Since the discovery of mechanically exfoliated graphene in 2004, research on ultrathin two-dimensional (2D) nanomaterials has grown exponentially in the fields of condensed matter physics, material science, chemistry, and nanotechnology. Highlighting their compelling physical, chemical, electronic, and optical properties, as well as their various potential applications, in this Review, we summarize the state-of-art progress on the ultrathin 2D nanomaterials with a particular emphasis on their recent advances. First, we introduce the unique advances on ultrathin 2D nanomaterials, followed by the description of their composition and crystal structures. The assortments of their synthetic methods are then summarized, including insights on their advantages and limitations, alongside some recommendations on suitable characterization techniques. We also discuss in detail the utilization of these ultrathin 2D nanomaterials for wide ranges of potential applications among the electronics/optoelectronics, electrocatalysis, batteries, supercapacitors, solar cells, photocatalysis, and sensing platforms. Finally, the challenges and outlooks in this promising field are featured on the basis of its current development.

Chitosan-Functionalized Graphene Oxide as a Potential Immunoadjuvant

The application of graphene oxide (GO) as a potential vaccine adjuvant has recently attracted considerable attention. However, appropriate surface functionalization of GO is crucial to improve its biocompatibility and enhance its adjuvant activity. In this study, we developed a simple method to prepare chitosan (CS)-functionalized GO (GO-CS) and further investigated its potential as a nanoadjuvant. Compared with GO, GO-CS possessed considerably smaller size, positive surface charge, and better thermal stability. The functionalization of GO with CS was effective in decreasing the non-specific protein adsorption and improving its biocompatibility. Furthermore, GO-CS significantly activated RAW264.7 cells and stimulated more cytokines for mediating cellular immune response, which was mainly due to the synergistic immunostimulatory effect of both GO and CS. GO-CS exhibits strong potential as a safe nanoadjuvant for vaccines and immunotherapy.

MEMS-based column coated with reduced graphene oxide as stationary phase for gas chromatography

Schematic diagram of single-layer stationary phase film (a) and two-step stationary phase film (b).

Graphene oxide-chitosan nanocomposites for intracellular delivery of immunostimulatory CpG oligodeoxynucleotides

CpG oligodeoxynucleotides (ODNs) activate innate and adaptive immune responses, and show strong potential as immunotherapeutic agents against various diseases. Benefiting from their unique physicochemical properties, graphene oxide (GO) has recently attracted great attention in nanomedicine. In this study, we developed a novel CpG ODNs delivery system based on GO-chitosan (GO-CS) nanocomposites. GO-CS nanocomposites were prepared by self-assembly of both components via electrostatic interactions. Compared with GO, GO-CS nanocomposites possessed smaller size, positive surface charge and lower cytotoxicity. CpG ODNs were loaded onto GO-CS nanocomposites via electrostatic interactions. GO-CS nanocomposites greatly improved the loading capacity and cellular uptake of CpG ODNs. GO-CS/CpG ODNs complexes further resulted in an enhanced interleukin-6 (IL-6) and tumor necrosis factor-α (TNF-α) production compared with that of free CpG ODNs and GO/CpG ODNs complexes. Therefore, GO-CS nanocomposites can serve as efficient nanocarriers for enhancing the delivery efficiency of CpG ODNs.

Challenges in Liquid-Phase Exfoliation, Processing, and Assembly of Pristine Graphene

Recent developments in the exfoliation, dispersion, and processing of pristine graphene (i.e., non-oxidized graphene) are described. General metrics are outlined that can be used to assess the quality and processability of various "graphene" products, as well as metrics that determine the potential for industrial scale-up. The pristine graphene production process is categorized from a chemical engineering point of view with three key steps: i) pretreatment, ii) exfoliation, and iii) separation. How pristine graphene colloidal stability is distinct from the exfoliation step and is dependent upon graphene interactions with solvents and dispersants are extensively reviewed. Finally, the challenges and opportunities of using pristine graphene as nanofillers in polymer composites, as well as as building blocks for macrostructure assemblies are summarized in the context of large-scale production.

Insight into In Situ Amphiphilic Functionalization of Few-Layered Transition Metal Dichalcogenide Nanosheets

A facile route toward functionalized amphiphilic layered transition-metal dichalcogenide nanosheets through in situ polymerization of polystyrene-polyacrylamide copolymers is established. The attachment of copolymers greatly affects their dispersibility in different kinds of solvents. Surface-tension components, polarity, and coordination effects of the copolymer are found to be the main factors affecting the dispersibility.