Alloying Nickel with Molybdenum Significantly Accelerates Alkaline Hydrogen Electrocatalysis

Stacking Fault-Enriched MoNi4/MoO2 Enables High-Performance Hydrogen Evolution

Producing green hydrogen in a cost-competitive manner via water electrolysis will make the long-held dream of hydrogen economy a reality. Although platinum (Pt)-based catalysts show good performance toward hydrogen evolution reaction (HER), the high cost and scarce abundance challenge their economic viability and sustainability. Here, a non-Pt, high-performance electrocatalyst for HER achieved by engineering high fractions of stacking fault (SF) defects for MoNi4/MoO2 nanosheets (d-MoNi) through a combined chemical and thermal reduction strategy is shown. The d-MoNi catalyst offers ultralow overpotentials of 78 and 121 mV for HER at current densities of 500 and 1000 mA cm-2 in 1 M KOH, respectively. The defect-rich d-MoNi exhibits four times higher turnover frequency than the benchmark 20% Pt/C, together with its excellent durability (> 100 h), making it one of the best-performing non-Pt catalysts for HER. The experimental and theoretical results reveal that the abundant SFs in d-MoNi induce a compressive strain, decreasing the proton adsorption energy and promoting the associated combination of *H into hydrogen and molecular hydrogen desorption, enhancing the HER performance. This work provides a new synthetic route to engineer defective metal and metal alloy electrocatalysts for emerging electrochemical energy conversion and storage applications.

Ligand-Induced Electronic Structure Modulation of Self-Evolved Ni3S2 Nanosheets for the Electrocatalytic Oxygen Evolution Reaction

Modulating the electronic structure of the electrocatalyst plays a vital role in boosting the electrocatalytic performance of the oxygen evolution reaction (OER). In this work, we introduced a one-step solvothermal method to fabricate 1,1-ferrocene dicarboxylic acid (FcDA)-decorated self-evolved nickel sulfide (Ni3S2) nanosheet arrays on a nickel foam (NF) framework (denoted as FcDA-Ni3S2/NF). Benefiting from the interconnected ultrathin nanosheet architecture, ligand dopants induced and facilitated in situ structural reconstruction, and the FcDA-decorated Ni3S2 (FcDA-Ni3S2/NF) outperformed its singly doped and undoped counterparts in terms of OER activity. The optimized FcDA-Ni3S2/NF self-supported electrode presents a remarkably low overpotential of 268 mV to achieve a current density of 10 mA cm-2 for the OER and demonstrates robust electrochemical stability for 48 h in a 1.0 M KOH electrolyte. More importantly, in situ electrochemical Raman spectroscopy reveals the generation of catalytically active oxyhydroxide species (NiOOH) derived from the surface construction during the OER of pristine FcDA-Ni3S2/NF, contributing significantly to its superior electrocatalytic performance. This study concerns the modulation of electronic structure through ligand engineering and may provide profound insight into the design of cost-efficient OER electrocatalysts.

Phase-Stabilized Nickel-Molybdenum Electrocatalyst by Samarium Doping for Hydrogen Evolution in Alkaline Water Electrolysis

Although the nickel-molybdenum electrocatalyst exhibits excellent activity in the alkaline hydrogen evolution reaction (HER), its stability is poor mainly due to molybdenum leaching. This work reports that doping samarium into nickel-molybdenum electrocatalyst effectively suppresses molybdenum leaching by forming a stable phase consisting of Sm, Mo, and O elements. The resulting electrode displays no noticeable activity degradation during the long-term testing (> 850 h) under a current density of 500 mA cm-2 in 1 м KOH. This enhanced stability is ascribed to the formation of a robust phase within the HER potential windows in alkaline electrolytes, as evidenced by the Pourbaix diagram. Furthermore, the samarium-modified electrocatalyst exhibits increased activity, with the overpotential decreasing by ≈59 mV from 159 to 100 mV at 500 mA cm-2 compared to the unmodified counterpart. These remarkable properties stem from samarium doping, which not only facilitates the formation of a stable phase to inhibit molybdenum leaching but also adjusts the electronic properties of molybdenum to enhance water dissociation.

Enabling Internal Electric Field in Heterogeneous Nanosheets to Significantly Accelerate Alkaline Hydrogen Electrocatalysis

Efficient bifunctional hydrogen electrocatalysis, encompassing both hydrogen evolution reaction (HER) and hydrogen oxidation reaction (HOR), is of paramount significance in advancing hydrogen-based societies. While non-precious-metal-based catalysts, particularly those based on nickel (Ni), are essential for alkaline HER/HOR, their intrinsic catalytic activity often falls short of expectations. Herein, an internal electric field (IEF) strategy is introduced for the engineering of heterogeneous nickel-vanadium oxide nanosheet arrays grown on porous nickel foam (Ni-V2O3/PNF) as bifunctional electrocatalysts for hydrogen electrocatalysis. Strikingly, the Ni-V2O3/PNF delivers 10 mA cm-2 at an overpotential of 54 mV for HER and a mass-specific kinetic current of 19.3 A g-1 at an overpotential of 50 mV for HOR, placing it on par with the benchmark 20% Pt/C, while exhibiting enhanced stability in alkaline electrolytes. Density functional theory calculations, in conjunction with experimental characterizations, unveil that the interface IEF effect fosters asymmetrical charge distributions, which results in more thermoneutral hydrogen adsorption Gibbs free energy on the electron-deficient Ni side, thus elevating the overall efficiency of both HER and HOR. The discoveries reported herein guidance are provided for further understanding and designing efficient non-precious-metal-based electrocatalysts through the IEF strategy.

Revealing the role of a bridging oxygen in a carbon shell coated Ni interface for enhanced alkaline hydrogen oxidation reaction

Encapsulating metal nanoparticles inside carbon layers is a promising approach to simultaneously improving the activity and stability of electrocatalysts. The role of carbon layer shells, however, is not fully understood. Herein, we report a study of boron doped carbon layers coated on nickel nanoparticles (Ni@BC), which were used as a model catalyst to understand the role of a bridging oxygen in a carbon shell coated Ni interface for the improvement of the hydrogen oxidation reaction (HOR) activity using an alkaline electrolyte. Combining experimental results and density functional theory (DFT) calculations, we find that the electronic structure of Ni can be precisely tailored by Ni-O-C and Ni-O-B coordinated environments, leading to a volcano type correlation between the binding ability of the OH* adsorbate and HOR activity. The obtained Ni@BC with a optimized d-band center displays a remarkable HOR performance with a mass activity of 34.91 mA mgNi-1, as well as superior stability and CO tolerance. The findings reported in this work not only highlight the role of the OH* binding strength in alkaline HOR but also provide guidelines for the rational design of advanced carbon layers used to coat metal electrocatalysts.

Interfacial engineering of POM-stabilized Ni quantum dots on porous titanium mesh for high-rate and stable alkaline hydrogen production

The development of low-cost, high-efficiency, and stable electrocatalysts for the alkaline hydrogen evolution reaction (HER) is a key challenge because the alkaline HER kinetics is slowed by an additional water dissociation step. Herein, we report an interfacial engineering strategy for polyoxometalate (POM)-stabilized nickel (Ni) quantum dots decorated on the surface of porous titanium mesh (POMs-Ni@PTM) for high-rate and stable alkaline hydrogen production. Benefiting from the strong interfacial interactions among POMs, Ni atoms, and PTM substrates, as well as unique POM-Ni quantum dot structures, the optimized POMs-Ni@PTM electrocatalyst exhibits a remarkable alkaline HER performance with an overpotential (η10) of 30.1 mV to reach a current density of 10 mA cm-2, which is much better than those of bare Ni decorated porous titanium mesh (Ni@PTM) (η10 = 171.1 mV) and POM decorated porous titanium mesh (POMs@PTM) electrocatalysts (η10 = 493.6 mV), comparable to that of the commercial 20 wt% platinum/carbon (20% Pt/C) electrocatalyst (η10 = 20 mV). Moreover, the optimized POMs-Ni@PTM electrocatalyst demonstrates excellent stability under continuous alkaline water-splitting at a current density of ∼100 mA cm-2 for 100 h, demonstrating great potential for its practical application.

Non-Noble Metal High-Entropy Alloy-Based Catalytic Electrode for Long-Life Hydrogen Gas Batteries

The development of efficient, stable, and low-cost bifunctional catalysts for the hydrogen evolution/oxidation reaction (HER/HOR) is critical to promote the application of hydrogen gas batteries in large scale energy storage systems. Here we demonstrate a non-noble metal high-entropy alloy grown on Cu foam (NNM-HEA@CF) as a self-supported catalytic electrode for nickel-hydrogen gas (Ni-H2) batteries. Experimental and theoretical calculation results reveal that the NNM-HEA catalyst greatly facilitates the HER/HOR catalytic process through the optimized electronic structures of the active sites. The assembled Ni-H2 battery with NNM-HEA@CF as the anode shows excellent rate capability and exceptional cycling performance of over 1800 h without capacity decay at an areal capacity of 15 mAh cm-2. Furthermore, a scaled-up Ni-H2 battery fabricated with an extended capacity of 0.45 Ah exhibits a high cell-level energy density of ∼109.3 Wh kg-1. Moreover, its estimated cost reaches as low as ∼107.8 $ kWh-1 based on all key components of electrodes, separator and electrolyte, which is reduced by more than 6 times compared to that of the commercial Pt/C-based Ni-H2 battery. This work provides an approach to develop high-efficiency non-noble metal-based bifunctional catalysts for hydrogen batteries in large-scale energy storage applications.

A Highly-Efficient Boron Interstitially Inserted Ru Anode Catalyst for Anion Exchange Membrane Fuel Cells

Developing high-performance electrocatalysts for alkaline hydrogen oxidation reaction (HOR) is crucial for the commercialization of anion exchange membrane fuel cells (AEMFCs). Here, boron interstitially inserted ruthenium (B-Ru/C) is synthesized and used as an anode catalyst for AEMFC, achieving a peak power density of 1.37 W cm-2 , close to the state-of-the-art commercial PtRu catalyst. Unexpectedly, instead of the monotonous decline of HOR kinetics with pH as generally believed, an inflection point behavior in the pH-dependent HOR kinetics on B-Ru/C is observed, showing an anomalous behavior that the HOR activity under alkaline electrolyte surpasses acidic electrolyte. Experimental results and density functional theory calculations reveal that the upshifted d-band center of Ru after the intervention of interstitial boron can lead to enhanced adsorption ability of OH and H2 O, which together with the reduced energy barrier of water formation, contributes to the outstanding alkaline HOR performance with a mass activity of 1.716 mA µgPGM -1 , which is 13.4-fold and 5.2-fold higher than that of Ru/C and commercial Pt/C, respectively.

Single Atom Ru Doped Ni2 P/Fe3 P Heterostructure for Boosting Hydrogen Evolution for Water Splitting

Modulating the chemical composition and structure has been considered as one of the most promising strategies for developing high-efficient water splitting catalysts. Here, a single-atom Ru doped Ni2 P/Fe3 P catalyst is synthesized by introducing the dispersed Ru atoms to adjust Ni2 P/Fe3 P heterostructure. Single atom Ru provides effective hydrogen evolution reaction (HER) active sites for boosting catalytic activities. The catalyst with only 0.2 wt.% content of Ru exhibits an overpotential of 19.3 mV at 10 mA cm-2 , which is obviously lower than 146.1 mV of Ni2 P/Fe3 P. Notably, an alkaline overall water electrolyzer based on Ru-Ni2 P/Fe3 P catalysts achieves a cell voltage of 1.47 V and operates over 600 h at 10 mA cm-2 , which is superior to that of benchmark RuO2 //Pt/C (1.61 V). The theoretical calculations further confirm that Ru single atom doping can effectively optimize the hydrogen/water adsorption free energy of the active site and therefore improve the HER activity of heterostructure. This work provides a valuable reference to design high-activity and durability catalyst for water splitting through the double modulation of interface-effect and atomic doping.

Construction of Heterostructure between Ni17W3 and WO2 to Boost the Hydrogen Oxidation Reaction in Alkaline Medium

The inferior intrinsic performance of Ni-based catalysts for the hydrogen oxidation reaction (HOR) in an alkaline medium seriously restricts the utilization of emerging anion-exchange membrane fuel cells (AEMFCs). This is because the hydrogen and hydroxyl binding energies on Ni need to be optimized. Although electrocatalysts obtained by alloying Ni with Mo or W reportedly exhibit enhanced activity, they are still far from industrial requirements based on unbalanced HBE and OHBE. Herein, we report to further enhance alkaline HOR activity by constructing a heterostructure between NiW alloy and metal oxide (Ni17W3/WO2), which is synthesized through solvothermal treatment combined with annealing. The as-fabricated reduced graphene oxide (rGO)-supported Ni17W3/WO2 (Ni17W3/WO2/rGO) exhibits state-of-the-art catalytic activity (current density of 2.9 mA cm-2 at 0.1 V vs RHE), faster kinetics (geometric kinetics current density of 4.0 mA cm-2 that can be comparable to Pt/C), and high stability (maintaining the current density for more than 80 h) toward HOR in alkaline media. The detailed characterizations reveal that the charge transfer across the boundary arising from constructing the as-prepared heterostructure tunes the electronic structures, ultimately facilitating the HOR process.

Optimizing Hydrogen and Hydroxyl Adsorption over Ru/WO2.9 Metal/Metalloid Heterostructure Electrocatalysts for Highly Efficient and Stable Hydrogen Oxidation Reactions in Alkaline Media

The development of high-performance, stable and platinum-free electrocatalysts for the hydrogen oxidation reaction (HOR) in alkaline media is crucial for the commercial application of anion exchange membrane fuel cells (AEMFCs). Ruthenium, as an emerging HOR electrocatalyst with a price advantage over platinum, still needs to solve the problems of low intrinsic activity and easy oxidation. Herein, Ru nanoparticles are anchored on the oxygen-vacancy-rich metalloid WO2.9 by interfacial engineering to create abundant and efficient Ru and WO2.9 interfacial active sites for accelerated HOR in alkaline media. Ru/WO2.9 /C displays excellent catalytic activity with mass activity (8.29 A mgNM -1 ) and specific activity (1.32 mA cmNM -2 ), which are 2.5/3.3 and 21.8/8.3 times that of PtRu/C and Pt/C, respectively. Moreover, Ru/WO2.9 /C exhibits excellent CO tolerance and operational stability. Experimental and theoretical studies reveal that the improved charge transfer from Ru to WO2.9 in the metal/metalloid heterostructure significantly tune the electronic structure of Ru sites and optimize the hydrogen binding energy (HBE) of Ru. While, WO2.9 provides abundant hydroxyl adsorption sites. Therefore, the equilibrium adsorption of hydrogen and hydroxyl at the interface of Ru/WO2.9 will be realized, and the oxidation of metal Ru would be avoided, thereby achieving excellent HOR activity and durability.

Metal-support interaction boosts the stability of Ni-based electrocatalysts for alkaline hydrogen oxidation

Ni-based hydrogen oxidation reaction (HOR) electrocatalysts are promising anode materials for the anion exchange membrane fuel cells (AEMFCs), but their application is hindered by their inherent instability for practical operations. Here, we report a TiO2 supported Ni4Mo (Ni4Mo/TiO2) catalyst that can effectively catalyze HOR in alkaline electrolyte with a mass activity of 10.1 ± 0.9 A g-1Ni and remain active even up to 1.2 V. The Ni4Mo/TiO2 anode AEMFC delivers a peak power density of 520 mW cm-2 and durability at 400 mA cm-2 for nearly 100 h. The origin for the enhanced activity and stability is attributed to the down-shifted d band center, caused by the efficient charge transfer from TiO2 to Ni. The modulated electronic structure weakens the binding strength of oxygen species, rendering a high stability. The Ni4Mo/TiO2 has achieved greatly improved stability both in half cell and single AEMFC tests, and made a step forward for feasibility of efficient and durable AEMFCs.

Exploring the degradation mechanism of nickel-copper-molybdenum hydrogen evolution catalysts during intermittent operation

We investigate the dynamic degradation behaviors of a nickel-copper-molybdenum hydrogen evolution catalyst in a liquid and solid polymer electrolyte to figure out its endurance in a renewable energy-driven electrolyzer. A cathode current protection approach is proposed to achieve a durable electrolyzer during intermittent operation.

Modifying charge transfer between rhodium and ceria for boosted hydrogen oxidation reaction in alkaline electrolyte

Sluggish kinetics of hydrogen oxidation reaction (HOR) in alkaline solution has restricted the rapid development of hydrogen economy. Constructing catalyst with metal-oxide heterostructures can enhance HOR performance; however, little studies concentrate on charge transfer between them, and the corresponding effects on reactions remain unclear. Herein, we report charge-transfer-adjustable CeO2/Rh interfaces uniformly dispersed on multiwalled carbon nanotube (CNT), which exhibit excellent alkaline HOR performance. Results confirm that the charge transfer from Rh to CeO2 could be conveniently tuned via thermal treatment. Consequently, the adsorption free energies of H* in Rh sites and OH* adsorption strength in CeO2 could be adjusted, as corroborated by density functional theory study. The optimized CeO2/Rh interfaces exhibit an exchange current density and a mass-specific kinetic current of 0.53 mA cmPGM-2 and 830 A gPGM-1 at an overpotential of 50 mV, respectively, which surpasses most of the advanced noble-metal-based electrocatalysts. This work provides a new insight of harnessing charge transfer of heterostructure to enhance catalytic activities.

Ultrathin Rh Nanosheets with Rich Grain Boundaries for Efficient Hydrogen Oxidation Electrocatalysis

Two-dimensional (2D) Pt-group ultrathin nanosheets (NSs) are promising advanced electrocatalysts for energy-related catalytic reactions. However, improving the electrocatalytic activity of 2D Pt-group NSs through the addition of abundant grain boundaries (GBs) and understanding the underlying formation mechanism remain significant challenges. Herein, we report the controllable synthesis of a series of Rh-based nanocrystals (e.g., Rh nanoparticles, Rh NSs, and Rh NSs with GBs) through a CO-mediated kinetic control synthesis route. In light of the 2D NSs' structural advantages and GB modification, the Rh NSs with rich GBs exhibit an enhanced electrocatalytic activity compared to pure Rh NSs and commercial Pt/C toward the hydrogen oxidation reaction (HOR) in alkaline media. Both experimental results and theoretical computations corroborate that the GBs in the Rh NSs have the capacity to ameliorate the adsorption free energy of reaction intermediates during the HOR, thus resulting in outstanding HOR catalytic performance. Our work offers novel perspectives in the realm of developing sophisticated 2D Pt-group metal electrocatalysts with rich GBs for the energy conversion field.

Modulating the d-Band Center Enables Ultrafine Pt3 Fe Alloy Nanoparticles for pH-Universal Hydrogen Evolution Reaction

By providing dual active sites to synergistically accelerate H2 O dissociation and H+ reduction, ordered intermetallic alloys usually show extraordinary performance for pH-universal hydrogen evolution reaction (HER). Herein, activated N-doped mesoporous carbon spheres supported intermetallic Pt3 Fe alloys (Pt3 Fe/NMCS-A), as a highly-efficient electrocatalyst for pH-universal HER, are reported. The Pt3 Fe/NMCS-A exhibits low overpotentials (η10 ) of 13, 29, and 48 mV to deliver 10 mA cm-2 in 0.5 m H2 SO4 , 1.0 m KOH, and 1.0 m phosphate buffered solution (PBS), respectively, as well as robust stability to maintain the overall catalytic performances. Theoretical studies reveal that the strong Pt 5d-Fe 3d orbital electronic interactions negatively shift the d-band center (εd ) of Pt 5d orbital, resulting in reduced H* adsorption energy of Pt sites and enhanced acidic HER activity. With Pt and Fe acting as co-adsorption sites for H* and *OH intermediates, respectively, a low energy barrier is required for Pt3 Fe/NMCS-A to dissociate H2 O to afford H* intermediates, which greatly promotes the H* adsorption and H2 formation in alkaline and neutral conditions. The synthetic strategy is further extended to the synthesis of Pt3 Co and Pt3 Ni alloys with excellent HER activity in pH-universal electrolytes, demonstrating the great potential of these Pt-based alloys for practical applications.

Platinum Species on Oxygen Vacancy-Rich Titania for Efficient Basic Electrocatalytic Hydrogen Evolution

Oxygen vacancy-rich titania is a promising support for enhancing the hydrogen evolution reaction (HER). This work innovatively loaded Pt nanoparticles on oxygen vacancy-rich TiO2 (Pt/Vo-TiO2) in situ by using a photocatalytic device. The synthesis conditions are mild, do not require high temperatures and strong reducing agents, and can avoid the accumulation of platinum species. X-ray photoelectron spectroscopy (XPS) and X-ray absorption spectrometry (XAS) verified the synergistic effect of Pt species and oxygen vacancies on the progress of the reaction kinetics, where the Pt particles exposed by the in situ synthesis functioned as reaction sites in the electrocatalytic hydrogen evolution. Based on this, Pt/Vo-TiO2 exhibits excellent electrocatalytic performance with an overpotential of only 56 mV at a current density of 10 mA cm-2 and a Tafel slope of only 73.5 mV dec-1. This work provides a new strategy for designing highly efficient HER catalysts.

Carbon-Doped Nickle Via a Fast Decarbonization Route for Enhanced Hydrogen Oxidation Reaction in Alkaline Media

Nickel (Ni) based materials with non-metal heteroatom doping are competitive substitutes for platinum group catalyst toward alkaline hydrogen oxidation reaction (HOR). However, the incorporation of non-metal atom into the lattice of conventional fcc phase Ni can easily trigger a structural phase transformation, forming hcp phase nonmetallic intermetallic compounds. Such tangle phenomenon makes it difficult to uncover the relationship between HOR catalytic activity and doping effect on fcc phase Ni. Herein, taking trace carbon doped Ni (C-Ni) nanoparticles as an example, a new nonmetal doped Ni nanoparticles synthesized by a simple fast decarbonization route using Ni3 C as precursor is presented, which provides an ideal platform to study the structure-activity relationship between alkaline HOR performance and non-metal doping effect toward fcc phase Ni. The obtained C-Ni exhibits an enhanced alkaline HOR catalytic activity compared with pure Ni, approaching to commercial Pt/C. X-ray absorption spectroscopy confirms that the trace carbon doping can modulate the electronic structure of conventional fcc phase nickel. Besides, theoretical calculations suggest that the introducing of C atoms can effectively regulate the d-band center of Ni atoms, resulting in the optimized hydrogen absorption, thereby improving the HOR activity.

A Unique Etching-Doping Route to Fe/Mo Co-Doped Ni Oxyhydroxide Catalyst for Enhanced Oxygen Evolution Reaction

Fe-doped Ni (oxy)hydroxide shows intriguing activity toward oxygen evolution reaction (OER) in alkaline solution, yet it remains challenging to further boost its performance. In this work, a ferric/molybdate (Fe3+ /MoO4 2- ) co-doping strategy is reported to promote the OER activity of Ni oxyhydroxide. The reinforced Fe/Mo-doped Ni oxyhydroxide catalyst supported by nickel foam (p-NiFeMo/NF) is synthesized via a unique oxygen plasma etching-electrochemical doping route, in which precursor Ni(OH)2 nanosheets are first etched by oxygen plasma to form defect-rich amorphous nanosheets, followed by electrochemical cycling to trigger simultaneously Fe3+ /MoO4 2- co-doping and phase transition. This p-NiFeMo/NF catalyst requires an overpotential of only 274 mV to reach 100 mA cm-2 in alkaline media, exhibiting significantly enhanced OER activity compared to NiFe layered double hydroxide (LDH) catalyst and other analogs. Its activity does not fade even after 72 h uninterrupted operation. In situ Raman analysis reveals that the intercalation of MoO4 2- is able to prevent the over-oxidation of NiOOH matrix from β to γ phase, thus keeping the Fe-doped NiOOH at the most active state.

Scalable production of foam-like nickel-molybdenum coatings via plasma spraying as bifunctional electrocatalysts for water splitting

Foam-like NiMo coatings were produced from an inexpensive mixture of Ni, Al, and Mo powders via atmospheric plasma spraying. The coatings were deposited onto stainless-steel meshes forming a highly porous network mainly composed of nanostructured Ni and highly active Ni4Mo. High material loading (200 mg cm-2) with large surface area (1769 cm2 per cm2) was achieved without compromising the foam-like characteristics. The coatings exhibited excellent activity towards both hydrogen evolution (HER) and oxygen evolution (OER) reactions in alkaline media. The HER active coating required an overpotential of 42 mV to reach a current density of -50 mA cm-2 with minimum degradation after a 24 h chronoamperometry test at -10 mA cm-2. Theoretical simulations showed that several crystal surfaces of Ni4Mo exhibit near optimum hydrogen adsorption energies and improved water dissociation that benefit the HER activity. The OER active coating also consisting of nanostructured Ni and Ni4Mo required only 310 mV to achieve a current density of 50 mA cm-2. The OER activity was maintained even after 48 h of continuous operation. We envisage that the development of scalable production techniques for Ni4Mo alloys will greatly benefit its usage in commercial alkaline water electrolysers.

IrMo Nanocluster-Doped Porous Carbon Electrocatalysts Derived from Cucurbit[6]uril Boost Efficient Alkaline Hydrogen Evolution

Electrocatalysts based on noble metals have been proven efficient for high-purity hydrogen production. However, the sluggish kinetics of the hydrogen evolution reaction (HER) in alkaline media caused by high water dissociation energy largely hampers this electrochemical process. To improve the electrocatalytic activity, we fabricate an effective porous carbon matrix derived from cucurbit[6]uril using a template-free method to support iridium-molybdenum (IrMo) nanoclusters. As proof of concept, the resulting IrMo-doped carbon electrocatalyst (IrMo-CBC) was found to boost the alkaline HER significantly. Owing to the unique in-plane hole structure and the nitrogen-rich backbone of cucurbit[6]uril as well as the ultrafine IrMo nanoclusters, IrMo-CBC exhibits pronounced alkaline HER activity with an extremely low overpotential of 12 mV at 10 mA cm^-2, an ultrasmall Tafel slope (28.06 mV dec^-1), a superior faradic efficiency (98%), and a TOF of 11.6 H₂ s^-1 at an overpotential of 50 mV, outperforming most iridium-based electrocatalysts and commercial Pt/C.

Anchoring cobalt molybdenum nickel alloy nanoparticles on molybdenum dioxide nanosheets as efficient and stable self-supported catalyst for overall water splitting at high current density

Developing bifunctional electrocatalysts with efficient and stable catalytic performance at high current density to improve the productivity of water splitting is important for relieving the environmental pollution and energy crisis. Herein, the Ni₄Mo and Co₃Mo alloy nanoparticles were anchored on MoO₂ nanosheets (H-NMO/CMO/CF-450) by annealing the NiMoO₄/CoMoO₄/CF (CF: self-made cobalt foam) under Ar/H₂ atmosphere. Benefitting from the nanosheets structure, synergistic effect of the alloys, existence of oxygen vacancy and the cobalt foam with smaller pore sizes as conductive substrate, the self-supported H-NMO/CMO/CF-450 catalyst demonstrates outstanding electrocatalytic performance, which delivers small overpotential of 87 (270) mV at 100 (1000) mA·cm^-2 for HER and 281 (336) mV at 100 (500) mA·cm^-2 for OER in 1 M KOH. Meanwhile, the H-NMO/CMO/CF-450 catalyst is used as working electrodes for overall water splitting, which just require 1.46 V @ 10 mA·cm^-2 and 1.71 V @ 100 mA·cm^-2, respectively. More importantly, the H-NMO/CMO/CF-450 catalyst can stabilize for 300 h at 100 mA·cm^-2 in both HER and OER. This research provides an idea for the preparation of stable and efficient catalysts at high current density.

Synergistic Regulation of Pt Clusters on Porous Support by Mo and P for Robust Bifunctional Hydrogen Electrocatalysis

Developing efficient electrocatalysts toward hydrogen oxidation and evolution reactions (HER/HOR) in alkaline electrolytes is essential for realizing renewable hydrogen technologies. Herein, we demonstrate that the introduction of dual-active species such as Mo and P (Pt/Mo,P@NC) can effectively regulate the surface electronic structure of platinum (Pt) and significantly improve the HOR/HER performance. The optimized Pt/Mo,P@NC exhibits remarkable catalytic activity, achieving a normalized exchange current density of 2.89 mA cm^-2 and a mass activity of 2.3 mA μg_Pt^-1, which are approximately 2.2 and 13.5 times higher than those of the state-of-the-art Pt/C catalyst, respectively. Moreover, it performs an impressive HER performance with an overpotential of 23.4 mV at 10 mA cm^-2, which is lower than most documented alkaline electrocatalysts. Experimental results reveal that the modifying effect of Mo and P optimizes the adsorption of H and OH on Pt/Mo,P@NC, resulting in an outstanding catalytic performance. This work has significant theoretical and practical significance for developing a novel and highly efficient catalyst for bifunctional hydrogen electrocatalysis.

NiMo solid-solution alloy porous nanofiber as outstanding hydrogen evolution electrocatalyst

Developing a high-efficiency hydrogen evolution reaction (HER) electrocatalyst for the large-scale production of hydrogen is essential but challenging. In this study, we used NiMo solid-solution alloy porous nanofibers to develop a robust HER electrocatalyst through electrospinning, oxidization, and high-temperature reduction treatment. In 1 M KOH electrolyte, the fabricated NiMo solid-solution alloy porous nanofibers exhibited higher HER activity than Ni nanofibers, which required a low overpotential of 69, 208, and 300 mV at 100, 500, and 1000 mA cm^-2, respectively, and had outstanding durability at 100 mA cm^-2 over 60 h. We developed a promising candidate for a high-efficiency HER electrocatalyst, and our findings provided valuable information for fabricating highly robust alloy-based electrocatalysts.

Solid-Liquid-Gas Management for Low-Cost Hydrogen Gas Batteries

Aqueous nickel-hydrogen gas (Ni-H₂) batteries with excellent durability (>10,000 cycles) are important candidates for grid-scale energy storage but are hampered by the high-cost Pt electrode with limited performance. Herein, we report a low-cost nickel-molybdenum (NiMo) alloy as an efficient bifunctional hydrogen evolution and oxidation reaction (HER/HOR) catalyst for Ni-H₂ batteries in alkaline electrolytes. The NiMo alloy demonstrates a high HOR mass-specific kinetic current of 28.8 mA mg^-1 at 50 mV as well as a low HER overpotential of 45 mV at a current density of 10 mA cm^-2, which is better than most nonprecious metal catalysts. Furthermore, we apply a solid-liquid-gas management strategy to constitute a conductive, hydrophobic network of NiMo using multiwalled carbon nanotubes (NiMo-hydrophobic MWCNT) in the electrode to accelerate HER/HOR activities for much improved Ni-H₂ battery performance. As a result, Ni-H₂ cells based on the NiMo-hydrophobic MWCNT electrode show a high energy density of 118 Wh kg^-1 and a low cost of only 67.5 $ kWh^-1. With the low cost, high energy density, excellent durability, and improved energy efficiency, the Ni-H₂ cells show great potential for practical grid-scale energy storage.

Heterostructural Ni-Ni0.2 Mo0.8 N Interface Engineering Boosts Alkaline Hydrogen Electrocatalysis

Exploring efficient and low-cost bifunctional catalysts for hydrogen evolution reaction (HER) and hydrogen oxidation reaction (HOR) is highly desirable for the achievement of unitized regenerative fuel cells. Herein, a facile method to prepare hetero-interfacial Ni-Ni_0.2 Mo_0.8 N nanosheets with tailored d-band for efficient alkaline hydrogen electrocatalysis is presented. Mechanism studies indicate that interface engineering can downshift the d-band center of Ni-Ni_0.2 Mo_0.8 N nanosheets due to the electron transfer from Ni to Ni_0.2 Mo_0.8 N, which weakens the binding strength of reaction intermediates, thereby boosting the catalytic performance. Relative to pure Ni, Ni-Ni_0.2 Mo_0.8 N nanosheets show a lower overpotential of 83 mV at -10 mA cm^-2 and good stability during 2,000 cycles for HER. Meanwhile, Ni-Ni_0.2 Mo_0.8 N nanosheets exhibit an improved exchange current density for HOR with a 10.2-fold enhancement in comparison with that of pure Ni. This work provides valuable insight into the reasonable design of efficient energy-related electrocatalysts based on the tailoring of d-band center by interface engineering.

Combining Highly Dispersed Amorphous MoS3 with Pt Nanodendrites as Robust Electrocatalysts for Hydrogen Evolution Reaction

Surface modification of electrocatalysts to obtain new or improved electrocatalytic performance is currently the main strategy for designing advanced nanocatalysts. In this work, highly dispersed amorphous molybdenum trisulfide-anchored Platinum nanodendrites (denoted as Pt-a-MoS₃  NDs) are developed as efficient hydrogen evolution electrocatalysts. The formation mechanism of spontaneous in situ polymerization MoS₄ ^2- into a-MoS₃ on Pt surface is discussed in detail. It is verified that the highly dispersed a-MoS₃ enhances the electrocatalytic activity of Pt catalysts under both acidic and alkaline conditions. The potentials at the current density of 10 mA cm^-2 (η₁₀ ) in 0.5 m sulfuric acid (H₂ SO₄ ) and 1 m potassium hydroxide (KOH) electrolyte are -11.5 and -16.3 mV, respectively, which is significantly lower than that of commercial Pt/C (-20.2 mV and -30.7 mV). This study demonstrates that such high activity benefits from the interface between highly dispersed a-MoS₃ and Pt sites, which act as the preferred adsorption sites for the efficient conversion of hydrion (H⁺ ) to hydrogen (H₂ ). Additionally, the anchoring of highly dispersed clusters to Pt substrate greatly enhances the corresponding electrocatalytic stability.

Bio-Inspired FeMo2S4 Microspheres as Bifunctional Electrocatalysts for Boosting Hydrogen Oxidation/Evolution Reactions in Alkaline Solution

Developing robust and effectual nonprecious electrocatalysts for the bifunctional hydrogen oxidation and evolution reactions (HOR and HER) in alkaline electrolyte is of critical significance for the realization of future hydrogen economy but challenging. Herein, this work demonstrates a new routine for the preparation of bio-inspired FeMo₂S₄ microspheres via the one-step sulfuration of Keplerate-type polyoxometalate {Mo₇₂Fe₃₀}. The bio-inspired FeMo₂S₄ microspheres feature potential-abundant structural defects and atomically precise iron doping and act as an effective bifunctional electrocatalyst for hydrogen oxidation/reduction reactions. The FeMo₂S₄ catalyst presents an impressive alkaline HOR activity compared to FeS₂ and MoS₂ with the high mass activity of 1.85 mA·mg^-1 and high specific activity as well as excellent tolerance to carbon monoxide poisoning. Meanwhile, FeMo₂S₄ electrocatalyst also displayed prominent alkaline HER activity with a low overpotential of 78 mV at a current density of 10 mA·cm^-2 and robust long-term durableness. Density functional theory (DFT) calculations indicate that the bio-inspired FeMo₂S₄ with a unique electron structure possesses the optimal hydrogen adsorption energy and enhanced adsorption of hydroxyl intermediates, which accelerates the potential-determining Volmer step, thus promoting the HOR and HER performance. This work provides a new pathway for designing efficient noble-metal-free electrocatalysts for the hydrogen economy.

Hydroxyl-Binding Energy-Induced Kinetic Gap Narrowing between Acidic and Alkaline Hydrogen Oxidation Reaction on Intermetallic Ru3 Sn7 Catalyst

Developing highly efficient catalysts toward alkaline hydrogen oxidation reaction (HOR) and narrowing the kinetic gap between acidic and alkaline electrolytes are of great importance for the practical application of alkaline exchange membrane fuel cell . Herein, ordered Ru₃ Sn₇ /C intermetallic compound has been developed for the HOR under alkaline and acidic conditions. The authors demonstrate that the ordered intermetallic Ru₃ Sn₇ /C shows much enhanced HOR activity, stability, and CO-tolerance compared with its disordered RuSn solid solution alloy counterpart. More importantly, the authors find that the kinetic gap of HOR between acidic and alkaline media is significantly narrowed in the as-synthesized intermetallic Ru₃ Sn₇ /C catalysts. Combined experiment results and theoretical calculations, the authors understand that promoted hydroxyl-binding energy on Ru₃ Sn₇ /C derived from the intermetallic-induced strong electron interaction is responsible for the accelerated alkaline HOR performance and narrowed kinetic gap.

Interfacial Chemical Bond Modulation of Co3(PO4)2-MoO3-x Heterostructures for Alkaline Water/Seawater Splitting

The development of a high current density with high energy conversion efficiency electrocatalyst is vital for large-scale industrial application of alkaline water splitting, particularly seawater splitting. Herein, we design a self-supporting Co₃(PO₄)₂-MoO_3-x/CoMoO₄/NF superaerophobic electrode with a three-dimensional structure for high-performance hydrogen evolution reaction (HER) by a reasonable devise of possible "Co-O-Mo hybridization" on the interface. The "Co-O-Mo hybridization" interfaces induce charge transfer and generation of fresh oxygen vacancy active sites. Consequently, the unique heterostructures greatly facilitate the dissociation process of H₂O molecules and enable efficient hydrogen spillover, leading to excellent HER performance with ultralow overpotentials (76 and 130 mV at 100 and 500 mA cm^-2) and long-term durability of 100 h in an alkaline electrolyte. Theoretical calculations reveal that the Co₃(PO₄)₂-MoO_3-x/CoMoO₄/NF promotes the adsorption/dissociation process of H₂O molecules to play a crucial role in improving the stability and activity of HER. Our results exhibit that the HER activity of non-noble metal electrocatalysts can be greatly enhanced by rational interfacial chemical bonding to modulate the heterostructures.

Interface Metal Oxides Regulating Electronic State around Nickel Species for Efficient Alkaline Hydrogen Electrocatalysis

Heterogeneous electrocatalysis typically depends on the surface electronic states of active sites. Modulating the surface charge state of an electrocatalysts can be employed to improve performance. Among all the investigated materials, nickel (Ni)-based catalysts are the only non-noble-metal-based alternatives for both hydrogen oxidation and evolution reactions (HOR and HER) in alkaline electrolyte, while their activities should be further improved because of the unfavorable hydrogen adsorption behavior. Hereto, Ni with exceptional HOR electrocatalytic performance by changing the d-band center by metal oxides interface coupling formed in situ is endowed. The resultant MoO₂ coupled Ni heterostructures exhibit an apparent HOR activity, even approaching to that of commercial 20% Pt/C benchmark, but with better long-term stability in alkaline electrolyte. An exceptional HER performance is also achieved by the Ni-MoO₂ heterostructures. The experiment results are rationalized by the theoretical calculations, which indicate that coupling MoO₂ with Ni results in the downshift of d-band center of Ni, and thus weakens hydrogen adsorption and benefits for hydroxyl adsorption. This concept is further proved by other metal oxides (e.g., CeO₂ , V₂ O₃ , WO₃ , Cr₂ O₃ )-formed Ni-based heterostructures to engineer efficient hydrogen electrocatalysts.

The Role of Discrepant Reactive Intermediates on Ru-Ru2 P Heterostructure for pH-Universal Hydrogen Oxidation Reaction

Developing highly efficient electrocatalysts for hydrogen oxidation reaction (HOR) under alkaline media is essential for the commercialization of alkaline exchange membrane fuel cell (AEMFC). However, the kinetics of HOR in alkaline media is complicated, resulting in orders of magnitude slower than that in acid, even for the state-of-the-art Pt/C. Here, we find that Ru-Ru₂ P/C heterostructure shows HOR performance with a non-monotonous variation in a whole pH region. Unexpectedly, an inflection point located at pH≈7 is observed, showing an anomalous behavior that HOR activity under alkaline media surpasses acidic media. Combining experimental results and theoretical calculations, we propose the roles of discrepant reactive intermediates for pH-universal HOR, while H* and H₂ O* adsorption strengths are responsible for acidic HOR, and OH* adsorption strength is essential for alkaline HOR. This work not only sheds light on fundamentally understanding the mechanism of HOR but also provides new designing principles for pH-targeted electrocatalysts.

Pt Single Atoms on CrN Nanoparticles Deliver Outstanding Activity and CO Tolerance in the Hydrogen Oxidation Reaction

The large-scale application of proton exchange membrane fuel cells is currently hampered by high cost of commercial Pt catalysts and their susceptibility to poisoning by CO impurities in H₂ feed. In this context, the development of CO-tolerant electrocatalysts with high Pt atom utilization efficiency for hydrogen oxidation reaction (HOR) is of critical importance. Herein, Pt single atoms are successfully immobilized on chromium nitride nanoparticles by atomic layer deposition method, denoted as Pt SACs/CrN. Electrochemical tests establish Pt SACs/CrN to be a very efficient HOR catalyst, with a mass activity that is 5.7 times higher than commercial PtRu/C. Strikingly, the excellent performance of Pt SACs/CrN is maintained after introducing 1000 ppm of CO in H₂ feed. The excellent CO-tolerance of Pt SACs/CrN is related to weaker CO adsorption on Pt single atoms. This work provides guidelines for the design and construction of active and CO-tolerant catalysts for HOR.

Electroshock synthesis of a bifunctional nonprecious multi-element alloy for alkaline hydrogen oxidation and evolution

The design and production of active, durable, and nonprecious electrocatalysts toward alkaline hydrogen oxidation and evolution reactions (HOR/HER) are extremely appealing for the implementation of hydrogen economy, but remain challenging. Here, we report a facile electric shock synthesis of an efficient, stable, and inexpensive NiCoCuMoW multi-element alloy on Ni foam (NiCoCuMoW) as a bifunctional electrocatalyst for both HOR and HER. For the HOR, the current density of NiCoCuMoW could reach ∼11.2 mA cm^-2 when the overpotential is 100 mV, higher than that for commercial Pt/C (∼7.2 mA cm^-2) and control alloy samples with less elements, along with superior CO tolerance. Moreover, for the HER, the overpotential at 10 mA cm^-2 for NiCoCuMoW is only 21 mV, along with a Tafel slope of low to 63.7 mV dec^-1, rivaling the commercial Pt/C as well (35 mV and 109.7 mV dec^-1). Density functional theory calculations indicate that alloying Ni, Co, Cu, Mo, and W can tune the electronic structure of individual metals and provide multiple active sites to optimize the hydrogen and hydroxyl intermediates adsorption, collaboratively resulting in enhanced electrocatalytic activity.

Ultrathin Ru-Ni nanounits as hydrogen oxidation catalysts with an alkaline electrolyte

The development of hydrogen-oxygen fuel cells with an alkaline electrolyte was highly limited by the sluggish kinetics of the hydrogen oxidation reaction (HOR). Here, with a pyrolysis-reduction route, a new RuNi-based electrocatalyst was prepared, which presents an ultrathin nanowire-like structure. In alkaline media, this catalyst shows an excellent catalytic performance with an exchange current density of 1.10 mA cm^-2_disk for hydrogen oxidation. The exchange current density and mass activity of this catalyst are much higher than those of its single-metal counterparts and even the commercial Pt/C catalyst containing 20% Pt. Such a remarkable catalytic activity can be explained by the interaction between Ru and Ni; the incorporation of Ni may induce an electronic effect on the optimization of the Ru-H_ad strength and provide a functional surface that can absorb OH species, thus boosting the catalytic activity. These findings may cast a new light on the exploration of low-cost but high-efficiency catalysts for fuel cells.

N-Doped Carbon as a Promoted Substrate for Ir Nanoclusters toward Hydrogen Oxidation in Alkaline Electrolytes

Development of effective electrocatalysts toward hydrogen oxidation with a low content of noble metals has attracted the attention of the catalytic community. In this work, a novel catalyst composed of nitrogen-doped carbon acting as the substrate and Ir nanoclusters as active species was prepared, which was then employed as an effective catalyst for the hydrogen oxidation reaction (HOR) in an alkaline electrolyte. In 0.1 M KOH, the optimized catalyst provides an exchange current density of 0.144 mA cm_Ir^-2 for HOR that outperforms the catalytic activity of the commercial Pt/C catalyst with a Pt content of 20 wt %. The substrate induces highly active Ir sites that markedly boosted the electrocatalytic activity for HOR. The nitrogen-doped carbon substrate increases the stability of Ir nanoclusters and decreases the absorption energy of hydrogen on Ir sites; at the same time, the higher electrostatic potential around the adsorbed hydrogen on Ir/N-doped carbon also enables them to be easily attracted by OH^- species, both of which enhanced the catalytic activity. The excellent catalytic activity and the understanding shown here will give some hints for the development of HOR catalysts used in alkaline electrolytes.

Dual Self-Built Gating Boosts the Hydrogen Evolution Reaction

Optimizing the intrinsic activity of active sites is an appealing strategy for accelerating the kinetics of the catalytic process. Here, a design principle, namely "dual self-built gating", is proposed to tailor the electronic structures of catalysts. Catalytic improvement is confirmed in a model catalyst with a ReS₂ -WS₂ /WS₂ hybridized heterostructure. As demonstrated in experimental and theoretical results, the dual gating can bidirectionally guide electron transfer and redistribute at the interface, endowing the model catalyst with an electron-rich region. The tailored electronic structures balance the adsorption of intermediates and the desorption of hydrogen synergistically to enhance the reaction kinetics for the hydrogen evolution reaction. Interestingly, the effect of dual gating can be easily amplified by the electric field. The overpotential and Tafel slope (49 mV, 35 mV dec^-1 ) obtained under the electric field for ReS₂ -WS₂ /WS₂ catalyst with the dual self-built gating effect are far below than those (210 mV, 116 mV dec^-1 ) of the pure WS₂ catalyst, which exhibits nearly four times improvement. The concept of dual gating can be applied to more systems, offering a new guideline for designing advanced electrocatalysts.

Designing 3d metal oxides: selecting optimal density functionals for strongly correlated materials

Transition metal oxides (TMOs) have remarkable physicochemical properties, are non-toxic, and have low cost and high annual production, thus they are commonly studied for various technological applications. Density functional theory (DFT) can help to optimize TMO materials by providing insights into their electronic, optical and thermodynamic properties, and hence into their structure-performance relationships, over a wide range of solid-state structures and compositions. However, this is underpinned by the choice of the exchange-correlation (XC) functional, which is critical to accurately describe the highly localized and correlated 3d-electrons of the transition metals in TMOs. This tutorial review presents a benchmark study of density functionals (DFs), ranging from generalized gradient approximation (GGA) to range-separated hybrids (RSH), with the all-electron def2-TZVP basis set, comparing magneto-electro-optical properties of 3d TMOs against experimental observations. The performance of the DFs is assessed by analyzing the band structure, density of states, magnetic moment, structural static and dynamic parameters, optical properties, spin contamination and computational cost. The results disclose the strengths and weaknesses of the XC functionals, in terms of accuracy, and computational efficiency, suggesting the unprecedented PBE0-1/5 as the best candidate. The findings of this work contribute to necessary developments of XC functionals for periodic systems, and materials science modelling studies, particularly informing how to select the optimal XC functional to obtain the most trustworthy description of the ground-state electron structure of 3d TMOs.