Phasor-FLIM analysis of cellulose paper ageing mechanism with carbotrace 680 dye

Ageing of paper is a complex process of great relevance for application purposes because of its widespread use as support for information storage in books and documents, and as common low-cost and green packaging material, to name a few. A key factor in paper ageing is the oxidation of cellulose, a macromolecule of natural origin that constitutes the main chemical component of paper. Such a complex process results in changes in the cellulose polymeric chains in chemical and structural properties. The scope of this work is to explore the effects of oxidation of cellulose as one of the principal mechanisms of ageing of paper using a fluorescence-based approach. To this aim, fluorescence-lifetime imaging microscopy (FLIM) measurements on pure cellulose samples stained using Carbotrace 680 dye were performed, and data were analyzed by phasor approach. The comparison with results from conventional techniques allowed to map paper microstructure as a function of the sample oxidation degree correlating the fluorescence-lifetime changes to cellulose oxidation. A two-step oxidation kinetics that produced specific modification in paper organization was highlighted indicating that FLIM measurements using Carbotrace 680 dye may provide a simple tool to obtain information on the oxidation process also adding spatial information at sub-micrometric scale.

Development of a colorimetric sensor based on nanofiber cellulose film modified with ninhydrin to measure the formalin index of fruit juice

In this research, a color sensor based on nanofiber cellulose film modified with ninhydrin was designed to measure amino acids and formalin index in fruit juice. For this purpose, three types of cellulose films with porosity of 5, 30 and 125 μm were used. These films were treated with standard solution of ninhydrin. The characteristics of modified films were investigated using Fourier transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM) and X-ray Diffraction (XRD) tests. The color factors of the sensors (a and b) changed in the presence of amino acids and juice with different levels of formalin index. Therefore, the modified films with ninhydrin as a colorimetric sensor were calibrated using 7 types of amino acids and based on the formalin index of 4 types of juice. Then the sensors were used to measure the formalin index in 4 types of juice. The results showed that the sensors have relative selectivity towards methionine amino acid. The formalin index values calculated in the juices by the sensor were compared with the titration method as a reference method. All three types of sensors were able to detect formalin index. The results of the sensor performance verification showed that the sensors can measure formalin index in different juices with 95-98 % accuracy. These sensors showed fast sensitivity and selectivity to the amino acids in juice, also these sensors are safe and the measurement method is fast and simple.

Value addition of rice straw cellulose fibers as a reinforcer in packaging applications

The potential use of agro-waste in food packaging applications is receiving remarkable attention due to its sustainable approach and biodegradable properties. As typical lignocellulosic biomass, rice straw (RS) is widely produced but is usually abandoned and burned, causing tremendous environmental concerns. The exploration of using RS as the source of biodegradable packaging materials is promising for economically converting this agricultural waste into packaging material, thereby providing a considerable solution for RS disposal and an alternative solution to synthetic plastic waste. Polymers have been infused with nanoparticles, fibers, and whiskers, along with plasticizers and cross-linkers, and fillers like nanoparticles and fibers. They have also been blended with natural extracts, essential oils, and other synthetic and natural polymers to improve RS properties. There is still much research to be done before this biopolymer can be applied at an industrial level in food packaging. In this respect, RS can be valued for packaging to add value to these underutilized residues. This review article focuses on the extraction methods and functionality of cellulose fibers and their nanostructured forms from RS and their utilization in packaging applications.

Effect of Microwave Plasma Pre-Treatment on Cotton Cellulose Dissolution

The utilization of cellulose to its full potential is constrained by its recalcitrance to dissolution resulting from the rigidity of polymeric chains, high crystallinity, high molecular weight, and extensive intra- and intermolecular hydrogen bonding network. Therefore, pretreatment of cellulose is usually considered as a step that can help facilitate its dissolution. We investigated the use of microwave oxygen plasma as a pre-treatment strategy to enhance the dissolution of cotton fibers in aqueous NaOH/Urea solution, which is considered to be a greener solvent system compared to others. Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy, Scanning Electron Microscopy, and Powder X-ray Diffraction analyses revealed that plasma pretreatment of cotton cellulose leads to physicochemical changes of cotton fibers. Pretreatment of cotton cellulose with oxygen plasma for 20 and 40 min resulted in the reduction of the molecular weight of cellulose by 36% and 60% and crystallinity by 16% and 25%, respectively. This reduction in molecular weight and crystallinity led to a 34% and 68% increase in the dissolution of 1% (w/v) cotton cellulose in NaOH/Urea solvent system. Thus, treating cotton cellulose with microwave oxygen plasma alters its physicochemical properties and enhanced its dissolution.

Utilization of Cellulose to Its Full Potential: A Review on Cellulose Dissolution, Regeneration, and Applications

As the most abundant natural polymer, cellulose is a prime candidate for the preparation of both sustainable and economically viable polymeric products hitherto predominantly produced from oil-based synthetic polymers. However, the utilization of cellulose to its full potential is constrained by its recalcitrance to chemical processing. Both fundamental and applied aspects of cellulose dissolution remain active areas of research and include mechanistic studies on solvent-cellulose interactions, the development of novel solvents and/or solvent systems, the optimization of dissolution conditions, and the preparation of various cellulose-based materials. In this review, we build on existing knowledge on cellulose dissolution, including the structural characteristics of the polymer that are important for dissolution (molecular weight, crystallinity, and effect of hydrophobic interactions), and evaluate widely used non-derivatizing solvents (sodium hydroxide (NaOH)-based systems, N,N-dimethylacetamide (DMAc)/lithium chloride (LiCl), N-methylmorpholine-N-oxide (NMMO), and ionic liquids). We also cover the subsequent regeneration of cellulose solutions from these solvents into various architectures (fibers, films, membranes, beads, aerogels, and hydrogels) and review uses of these materials in specific applications, such as biomedical, sorption, and energy uses.

Production and Surface Modification of Cellulose Bioproducts

Petroleum-based synthetic plastics play an important role in our life. As the detrimental health and environmental effects of synthetic plastics continue to increase, the renewable, degradable and recyclable properties of cellulose make subsequent products the "preferred environmentally friendly" alternatives, with a small carbon footprint. Despite the fact that the bioplastic industry is growing rapidly with many innovative discoveries, cellulose-based bioproducts in their natural state face challenges in replacing synthetic plastics. These challenges include scalability issues, high cost of production, and most importantly, limited functionality of cellulosic materials. However, in order for cellulosic materials to be able to compete with synthetic plastics, they must possess properties adequate for the end use and meet performance expectations. In this regard, surface modification of pre-made cellulosic materials preserves the chemical profile of cellulose, its mechanical properties, and biodegradability, while diversifying its possible applications. The review covers numerous techniques for surface functionalization of materials prepared from cellulose such as plasma treatment, surface grafting (including RDRP methods), and chemical vapor and atomic layer deposition techniques. The review also highlights purposeful development of new cellulosic architectures and their utilization, with a specific focus on cellulosic hydrogels, aerogels, beads, membranes, and nanomaterials. The judicious choice of material architecture combined with a specific surface functionalization method will allow us to take full advantage of the polymer's biocompatibility and biodegradability and improve existing and target novel applications of cellulose, such as proteins and antibodies immobilization, enantiomers separation, and composites preparation.

Advanced Characterization of Organic Matter Decaying during Composting of Industrial Waste Using Spectral Methods

To date, compost maturation monitoring is carried out by physical-chemical and microbiological analysis, which could be considered an overweening consumption of time and products. Nowadays, spectroscopy is chosen as a simple tool for monitoring compost maturity. In the present investigation, spectroscopy analysis was performed in the interest of corroborating the compost maturity. This goal was achieved by using the X-ray diffraction, infrared spectroscopy, and scanning electron microscopy. X-ray diffraction analysis showed the presence of the cellulose fraction in compost samples. At the same time, the intensity of pics decreased depending on composting time, thus proving that there was organic matter degradation. Infrared and scanning electron microscopy analysis allow for confirming these results. The correlation between spectroscopies analysis and physical-chemical properties was employed by partial least squares-regression (PLS-R) model. PLS-R model was applied to build a model to predict the compost quality depending on the composting time, the results obtained show that all the parameters analysis are well predicted. The current study proposed that final compost was more stabilized compared with the initial feedstock mixture. Ultimately, spectroscopy techniques used allowed us to confirm the physical-chemical results obtained, and both of them depict maturity and stability of the final compost, thus proving that spectral techniques are more reliable, fast, and promising than physical-chemical analyses.

Green Synthesis of Copper Nanoparticles Using Cotton

Copper nanoparticles (CuNP) were obtained by a green synthesis method using cotton textile fibers and water as solvent, avoiding the use of toxic reducing agents. The new synthesis method is environmentally friendly, inexpensive, and can be implemented on a larger scale. This method showed the cellulose capacity as a reducing and stabilizing agent for synthetizing Cellulose–Copper nanoparticles (CCuNP). Nanocomposites based on CCuNP were characterized by XRD, TGA, FTIR and DSC. Functional groups present in the CCuNP were identified by FTIR analysis, and XRD patterns disclosed that nanoparticles correspond to pure metallic Cu°, and their sizes are at a range of 13–35 nm. Results demonstrated that CuNPs produced by the new method were homogeneously distributed on the entire surface of the textile fiber, obtaining CCuNP nanocomposites with different copper wt%. Thus, CuNPs obtained by this method are very stable to oxidation and can be stored for months. Characterization studies disclose that the cellulose crystallinity index (CI) is modified in relation to the reaction conditions, and its chemical structure is destroyed when nanocomposites with high copper contents are synthesized. The formation of CuO nanoparticles was confirmed as a by-product, through UV spectroscopy, in the absorbance range of 300–350 nm.

Bio-Based Plasticized PVA Based Polymer Blend Electrolytes for Energy Storage EDLC Devices: Ion Transport Parameters and Electrochemical Properties

This report shows a simple solution cast methodology to prepare plasticized polyvinyl alcohol (PVA)/methylcellulose (MC)-ammonium iodide (NH₄I) electrolyte at room temperature. The maximum conducting membrane has a conductivity of 3.21 × 10^-3 S/cm. It is shown that the number density, mobility and diffusion coefficient of ions are enhanced by increasing the glycerol. A number of electric and electrochemical properties of the electrolyte-impedance, dielectric properties, transference numbers, potential window, energy density, specific capacitance (C_s) and power density-were determined. From the determined electric and electrochemical properties, it is shown that PVA: MC-NH₄I proton conducting polymer electrolyte (PE) is adequate for utilization in energy storage device (ESD). The decrease of charge transfer resistance with increasing plasticizer was observed from Bode plot. The analysis of dielectric properties has indicated that the plasticizer is a novel approach to increase the number of charge carriers. The electron and ion transference numbers were found. From the linear sweep voltammetry (LSV) response, the breakdown voltage of the electrolyte is determined. From Galvanostatic charge-discharge (GCD) measurement, the calculated C_s values are found to drop with increasing the number of cycles. The increment of internal resistance is shown by equivalent series resistance (ESR) plot. The energy and power density were studied over 250 cycles that results to the value of 5.38-3.59 Wh/kg and 757.58-347.22 W/kg, respectively.

Cellulose Dissolution in Ionic Liquid under Mild Conditions: Effect of Hydrolysis and Temperature

This study investigated the effect of acid hydrolysis of cellulose on its dissolution under mild conditions in ionic liquid, 1-butyl-3-methylimidazolium acetate/N,N-dimethylacetamide (BMIMAc/DMAc). Acid hydrolysis of high molecular weight (MW) cotton cellulose (DP > 4000) was carried out to produce hydrolyzed cotton (HC) samples for dissolution. The HC samples were characterized using gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA), and the dissolution process was monitored using polarized light microscopy (PLM). It was found that the drastic decrease of the MW of cellulose did not result in improvement of its dissolution at room temperature. As compared to original cotton cellulose, the high amount of undissolved fibers in HC solutions led to unstable rheological behavior of HC solutions. Agglomeration and inhomogeneous dispersion of HC, and increased crystallinity, in this case, likely made the diffusion of BMIMAc/DMAc more difficult to the inside of the polymeric network of cellulose at ambient temperature, thereby hindering the dissolution. However, increasing the temperature from room temperature to 35 °C and 55 °C, led to a significant improvement in cellulose dissolution. This phenomenon implies that reducing the MW of cellulose might not be able to improve its dissolution under certain conditions. During the dissolution process, the physical properties of cellulose including fiber aggregation status, solvent diffusivity, and cellulose crystallinity may play a critical role compared to the MW, while the MW may not be an important factor. This finding may help further understand the mechanism of cellulose dissolution and seek better strategies to dissolve cellulose under mild conditions for industrial applications.

Isolation and characterization of micro and nanocrystalline cellulose fibers from the walnut shell, corncob and sugarcane bagasse

The present study aims to extract and characterize the microcrystalline cellulose (MCC) present in different agro-industrial wastes such as walnut shells, corncob, and sugarcane bagasse. Moreover, it is also the aim of this study to convert MCCs to nanocrystalline cellulose fiber (NCCF), to demonstrate the difference in morphological, structural, thermal, and chemical natures. Corncob cellulose was observed to possess a loosely bounded linear bundle structure. Nanocrystalline cellulose fiber yield from walnut shell and sugarcane bagasse cellulose were higher than corncob cellulose. The thermal stability of cellulose was noted to be high for walnut shell NCCF. Nanocrystalline cellulose fiber of corncob and sugarcane bagasse was estimated to have a low thermal degradation temperature. All the MCCs and NCCFs produced from investigated cellulose sources were found to have type I cellulose. Functional group compositions of cellulose were observed to be intact for converted agro-based NCCF's.

Evolution of Microbial Composition and Enzymatic Activities during the Composting of Textile Waste

The production of stable and mature compost often depends on the performance of microbes and their enzymatic activity. Environmental and nutritional conditions influence the characteristics of microbial communities and, therefore, the dynamics of major metabolic activities. Using three waste mixtures (textile waste mixed with either green, paper, or cardboard waste), the maturity of the compost produced was assessed by following the physico-chemical parameters and enzymatic activities provided by the microorganisms that were identified using next-generation sequencing (NGS). Among the three mixtures used, it was found that the two best mixtures showed C/N ratios of 16.30 and 16.96, total nitrogen of 1.37 and 1.39%, cellulase activities of 50.62 and 52.67 Ug−1, acid phosphatase activities of 38.81 and 68.77 Ug−1, and alkaline phosphatase activities of 51.12 and 56.86 Ug−1. In addition, several lignocellulosic species, together with those that are able to solubilize phosphate, were identified. Among those known for cellulase and acid/alkaline phosphatase activities, bacteria belonging to the Proteobacteria, Bacteroidetes, Actinobacteria, and Firmicutes phyla were shown. The presence of species belonging to the Ascomycota and Basidiomycota phyla of Fungi, which are known for their ability to produce cellulase and acid/alkaline phosphatases, was demonstrated. These findings provide a basis for the production of stable and mature compost based on textile waste.

Structural characterization of Argania spinosa Moroccan wooden artifacts during natural degradation progress using infrared spectroscopy (ATR-FTIR) and X-Ray diffraction (XRD)

The present work is focused on spectroscopic study of four samples of Argan wooden artifact pertaining to the 17^th, 18^th, 20^th and 21^st centuries. The objective is to characterize their unknown structures by the study of their non degraded parts and to investigate changes occurred in their degraded parts due to the natural degradation process. Attenuated total reflectance Fourier transform infrared spectroscopy gauges the presence of many functional groups related to cellulose I and/or II (OH, C–O–C and –CH₂), hemicelluloses (particularly C=O acetoxy ester band at 1732 cm⁻¹), and lignin (OH phenolic, C_ar-O and C=C_ar) and provides qualitative information on the state of wood alteration by informing on the evolution of new former C=O bands. The degree of conversion to carbonyl group, especially quinone or p-quinone at 1650 cm⁻¹, is correlated to lignin degradation, while the absence of the C=O acetoxy absorption is ascribable to occurred deterioration in hemicelluloses, and partial degradation of cellulose with enhancement of the C=O region between 1730-1630 cm⁻¹. X-ray diffraction determines the presence of two forms of cellulose; amorphous cellulose at 18.5° 2θ and predominant crystalline cellulose I_β at 2θ = 22.6° which characterized by an intense peak. The decrease of crystallinity index values confirms the deterioration level and obvious changes in crystallinity level. However, the microcrystalline structure appears unaltered because no significant changes were observed for calculated cristallite seize. The obtained results depend on the prolonged time of ageing, natural deterioration phenomena, and wood part (internal or external) that is exposed to degradation. The combination of these two methods is useful for an accurate estimation of the degradation level of argan wood.

Composite Films with UV-Barrier Properties of Bacterial Cellulose with Glycerol and Poly(vinyl alcohol): Puncture Properties, Solubility, and Swelling Degree

The aim of this study was to develop composite films based on bacterial cellulose, glycerol, and poly(vinyl alcohol) with improved optical and mechanical properties and good UV-barrier property. The interaction among the compounds was analyzed using Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetry, and differential scanning calorimetry. The mechanical properties (toughness, burst strength, and distance to burst), solubility, water adsorption, and light barrier properties of the composite films were evaluated. Polynomial models obtained allowed us to predict the behavior of these properties. Poly(vinyl alcohol) showed a reinforcing effect on the bacterial cellulose matrix, while glycerol showed a noticeable plasticizing behavior. The bacterial cellulose-based composites showed toughness values ranging from 0.22 to 2.60 MJ/m³. The burst strength values obtained ranged between 43.74 and 2105.52 g. The distance to burst ranged from 0.39 to 4.94 mm. The film solubility on water ranged from 9.37 to 31.65%, and the water retention ranged from 78.26 to 364.78%. Glycerol decreased the transmittance in the UV region, improving the UV-barrier properties of the films, while poly(vinyl alcohol) improved the transparency and opacity values of the samples. The transmittance in the UV regions (A, B, and C) ranged from 1 to 48.51%, increasing with the poly(vinyl alcohol) concentration.

Surface engineering of spongy bacterial cellulose via constructing crossed groove/column micropattern by low-energy CO2 laser photolithography toward scar-free wound healing

Bacterial cellulose (BC) is a bio-derived polymer, and it has been considered as an excellent candidate material for tissue engineering. In this study, a crossed groove/column micropattern was constructed on spongy, porous BC using low-energy CO₂ laser photolithography. Applying the targeted immobilization of a tetrapeptide consisting of Arginine-Glycine-Aspartic acid-Serine (H-Arg-Gly-Asp-Ser-OH, RGDS) as a fibronectin onto the column platform surface, the resulting micropatterned BC (RGDS-MPBC) exhibited dual affinities to fibroblasts and collagen. Material characterization of RGDS-MPBC revealed that the micropattern was built by the column part with size of ~100 × 100 μm wide and ~100 μm deep, and the groove part with size of ~150 μm wide. Hydrating the MPBC did not result in the collapse of the integrity of the micropattern, suggesting its potential application in a highly hydrated wound environment. Cell culture assays revealed that the RGDS-MPBC exhibited an improved cytotoxicity to mouse fibroblasts L929, as compared to the pristine BC. Meanwhile, it was observed that the RGDS-MPBC was able to guide the ordered aggregation of human skin fibroblast (HSF) cells on the column platform surface, and no HSF cells were found in the groove channels. Over time, it was found that a dense network of collagen was gradually established across the groove channels. Furthermore, the in-vivo animal study preliminarily demonstrated the scar-free healing potential of the micropatterned BC materials. Therefore, this RGDS-MPBC material exhibited its advantages in guiding cell migration and collagen distribution, which could present a prospect in the establishment of "basket-woven" organization of collagen in normal skin tissue against the formation of dense, parallel aggregation of collagen fibers in scar tissue toward scar-free wound healing outcome.

Cellulose transparent conductive film and its feasible use in perovskite solar cells

A transparent conductive Ag nanowire (AgNW)-regenerated cellulose film (RCF) was prepared and has been proposed to be used as an anode for perovskite solar cells.