Oxidizing Electrode Potentials Decrease Current Production and Coulombic Efficiency through Cytochrome cInactivation inShewanella oneidensisMR-1

Periodic step polarization accelerates electron recovery by electroactive biofilms (EABs)

Relatively low rate of electron recovery is one of the factors that limit the advancement of bioelectrochemical systems. Here, new periodic polarizations were investigated with electroactive biofilms (EABs) enriched from activated sludge and Geobacter sulfurreducens biofilms. When representative anode potentials (E_a ) were applied, redox centers with midpoint potentials (E_mid ) higher than E_a were identified by localized cyclic voltammetry. The electrons held by these redox centers were accessible when E_a was raised to 0.4 V (vs. Ag/AgCl). New periodic polarizations that discharge at 0.4 V recovered electrons faster than normal periodic and fixed-potential polarizations. The best-performing periodic step polarization accelerated electron recovery by 23%-24% and 12%-76% with EABs and G. sulfurreducens biofilms, respectively, compared to the fixed-potential polarization. Quantitative reverse transcription polymerase chain reaction showed an increased abundance of omcZ mRNA transcripts from G. sulfurreducens after periodic step polarization. Therefore, both the rate of energy recovery by EABs and the performance of bioelectrochemical systems can be enhanced by improving the polarization schemes.

A high-efficiency mixotrophic photoelectroactive biofilm reactor (MPBR) for enhanced simultaneous removal of nutrients and antibiotics by integrating light intensity regulation and microbial extracellular electron extraction

The performance of a mixotrophic photoelectroactive biofilm reactor (MPBR) was improved in order to achieve enhanced simultaneous removal of multiple aqueous pollutants and the production of valuable biomass. The MPBR was optimized by integrating the regulation of light intensity (3000, 8000 and 23000 lux) and microbial extracellular electron extraction (using an electrode at -0.3, 0 and 0.3 V). Results showed that the MPBR operated at a high light intensity (23000 lux) with a potential of -0.3 V (Coulomb efficiency (CE) of 9.65%) achieved maximum pollutant removal efficiencies, effectively removing 65% NH₄⁺-N, 95% PO₄^3--P and 52% sulfadiazine (SDZ) within 72 h, exhibiting an increase by 30%, 56% and 26% compared to an MPBR operated at the same light intensity but without an externally applied potential. The use of an electrode with an applied potential of -0.3V was most suitable for the extraction of photosynthetic electrons from the photoelectroactive biofilm, in which Rhodocyclaceae was highly enriched, effectively alleviating photoinhibition and thereby enhancing N, P assimilation and SDZ degradation under high light conditions. A maximum lipid content of 409.28 mg/g was obtained under low light intensity (3000 lux) conditions with an applied potential of 0.3 V (CE 9.08%), while a maximum protein content of 362.29 mg/g was obtained at a low light intensity (3000 lux) and 0 V (CE 10.71%). The selective enrichment of Chlorobium and the subsequent enhanced conversion of excess available carbon under low light and positive potential stimulation conditions, were responsible for the enhanced accumulation of proteins and lipids in biomass.

Electrochemical Characteristics of Shewanella loihica PV-4 on Reticulated Vitreous Carbon (RVC) with Different Potentials Applied

The current output of an anodic bioelectrochemical system (BES) depends upon the extracellular electron transfer (EET) rate from electricigens to the electrodes. Thus, investigation of EET mechanisms between electricigens and solid electrodes is essential. Here, reticulated vitreous carbon (RVC) electrodes are used to increase the surface available for biofilm formation of the known electricigen Shewanella loihica PV-4, which is limited in conventional flat electrodes. S. loihica PV-4 utilizes flavin-mediated EET at potential lower than the outer membrane cytochromes (OMC), while at higher potential, both direct electron transfer (DET) and mediated electron transfer (MET) contribute to the current output. Results show that high electrode potential favors cell attachment on RVC, which enhances the current output. DET is the prevailing mechanism in early biofilm, while the contribution of MET to current output increased as the biofilm matured. Electrochemical analysis under starvation shows that the mediators could be confined in the biofilm. The morphology of biofilm shows bacteria distributed on the top layer of honeycomb structures, preferentially on the flat areas. This study provides insights into the EET pathways of S. loihica PV-4 on porous RVC electrodes at different biofilm ages and different set potential, which is important for the design of real-world BES.

Enhanced production of microalgae-originated photosensitizer by integrating photosynthetic electrons extraction and antibiotic induction towards photocatalytic degradation of antibiotic: A novel complementary treatment process for antibiotic removal from effluent of conventional biological wastewater treatment

Antibiotic residues in effluents from bio-treated wastewaters are mainly responsible for the spread of antibiotic resistance genes in the environment. Conventional physicochemical treatments are thought to be unsustainable due to high energy consumption, large consumption of chemicals and environmental unfriendly processing step. In this study, a novel approach by integrating photosynthetic electrons extraction from microalgae with antibiotic induction was used to enhance the production of microalgae-originated photosensitizer for photolytic removal of antibiotic residues in effluents from conventional bio-treated wastewaters. Results showed that the accumulation of photoactive substances in extracellular polymeric substance (EPS) of chlorella vulgaris was positively related to the amounts of photosynthetic electrons extracted by the electrode which is a potential-dependent process and can be further enhanced by tetracycline (TC) induction. The protein and humic acid which are considered two main photoactive substances in EPS produced at 0.6 V accumulated to a high level of 320 and 24 μg/cm³ and were further increased to 380 and 48 μg/cm³ when TC was added which were 4.7 and 6.4-folds higher than that produced at potential free in the absence of TC. The EPS produced at 0.6 and 0.8 V led to 1.34 and 1.53-fold acceleration in photosensitized degradation of TC compared to that of EPS free in secondary effluent of municipal wastewater treatment plant. The complex heterocyclic ring structure of TC was broken down into simple monocyclic aromatic compounds, indicating a marked reduction in biotoxicity and recalcitrance. The hydroxyl radical played a main role for the photolysis of TC followed by singlet oxygen. This technology provides a new alternative to conventional physicochemical treatment as complementary treatment processes for biological wastewater treatment in terms of antibiotics removal.

Conjugated Polyelectrolyte/Bacteria Living Composites in Carbon Paper for Biocurrent Generation

Successful practical implementation of bioelectrochemical systems requires developing affordable electrode structures that promote efficient electrical communication with microbes. Recent efforts have centered on immobilizing bacteria with organic semiconducting polymers on electrodes via electrochemical methods. This approach creates a fixed biocomposite that takes advantage of the increased electrode's electroactive surface area (EASA). Here, we demonstrate that a biocomposite comprising the water-soluble conjugated polyelectrolyte CPE-K and electrogenic Shewanella oneidensis MR-1 can self-assemble with carbon paper electrodes, thereby increasing its biocurrent extraction by ∼ 6-fold over control biofilms. A ∼ 1.5-fold increment in biocurrent extraction was obtained for the biocomposite on carbon paper relative to the biocurrent extracted from gold-coated counterparts. Electrochemical characterization revealed that the biocomposite stabilized with the carbon paper more quickly than atop flat gold electrodes. Cross-sectional images show that the biocomposite infiltrates inhomogeneously into the porous carbon structure. Despite an incomplete penetration, the biocomposite can take advantage of the large EASA of the electrode via long-range electron transport. These results show that previous success on gold electrode platforms can be improved when using more commercially viable and easily manipulated electrode materials. This article is protected by copyright. All rights reserved.

Enhanced removal of veterinary antibiotic from wastewater by photoelectroactive biofilm of purple anoxygenic phototroph through photosynthetic electron uptake

Purple anoxygenic phototrophs have been recently attracted substantial attention for their growing potential in wastewater treatment and their diverse metabolic patterns can be regulated for process control and optimization. In this study, the photoheterotrophic metabolism of Rhodopseudomonas palustris (R. palustris) was modified by photosynthetic electron uptake using a poised electrode which was explored to enhance removal of veterinary antibiotic from aqueous medium. The results showed that R. palustris grown as biofilm on electrode surface had excellent photoelectroactive activity and the photosynthetic electron uptake from the photoelectroactive biofilm significantly enhanced antibiotic florfenicol (FLO) degradation. The specific degradation rate of FLO at the set electrode potential of 0 V was 2.59-fold higher than that without applied potential. Enhanced co-metabolic reductive dehalogenation by use of the photosynthetic electrons extracted from co-substrate was mainly responsible for FLO degradation which eliminated the antibacterial activity of FLO. The electrode potential controlled the processes of photosynthetic electron uptake and its resultant FLO degradation. The fastest degradation of FLO was achieved at 0 V because the electrode poised at this potential stroke a proper balance between the enhancing photosynthetic electron uptake by serving as electron acceptor and minimizing competition with FLO for the photosynthetic electron from co-substrate. The activity of photoelectroactive biofilm was not negatively affected by FLO at environmental relevant concentration, suggesting its great potential for removal of antibiotic contaminants in wastewater. R. palustris could serve as a reservoir for floR resistance gene but its abundance can be diminished by choosing appropriate electrode potential.

Understanding the interdependence of strain of electrotroph, cathode potential and initial Cu(II) concentration for simultaneous Cu(II) removal and acetate production in microbial electrosynthesis systems

Metallurgical microbial electrosynthesis systems (MES) are holding great promise for simultaneous heavy metal removal and acetate production from heavy metal-contaminated and organics-barren waters. How critical parameters of strain of electrotroph, cathode potential and initial heavy metal concentration affect MES performance, however, is not yet fully understood. Heavy metal of Cu(II) and four Cu(II)-tolerant electrotrophs (Stenotrophomonas maltophilia JY1, Citrobacter sp. JY3, Pseudomonas aeruginosa JY5 and Stenotrophomonas sp. JY6) were employed to evaluate MES performance at various cathode potentials (-900 or -600 mV vs. standard hydrogen electrode) and initial Cu(II) concentrations (60-120 mg L^-1). Each electrotrophs exhibited incremental Cu(II) removals with increased Cu(II) at -900 mV, higher than at -600 mV or in the abiotic controls. Acetate production by JY1 and JY6 decreased with the increase in initial Cu(II), compared to an initial increase and a decrease thereafter for JY3 and JY5. For each electrotrophs, the biofilms than the planktonic cells released more amounts of extracellular polymeric substances (EPS) with a compositional diversity and stronger Cu(II) complexation at -900 mV. These were higher than at -600 mV, or in the controls either under open circuit conditions or in the absence of Cu(II). This work demonstrates the interdependence of strain of electrotroph, cathode potential and initial Cu(II) on simultaneous Cu(II) removal and acetate production through the release of different amounts of EPS with diverse composites, contributing to enhancing the controlled MES for efficient recovery of value-added products from Cu(II)-contaminated and organics-barren waters.

Enhanced extracellular electron transfer between Shewanella putrefaciens and carbon felt electrode modified by bio-reduced graphene oxide

Extracellular electron transfer (EET) is a governing factor for the electrochemical performance of a bioelectrochemical system (BES) such as the microbial fuel cell (MFC). Herein, an in situ method to fabricate a bio-reduced graphene oxide (GO) (br-GO) modified carbon felt electrode to increase EET was developed. GO (0.5mgmL^-1) was spiked into the anode chamber in a three-electrode BES and was transformed to br-GO with a self-assembled three-dimensional (3D) structure. The response of the br-GO modified electrode potential to the attached population of Shewanella putrefaciens increased from 0.071V to 0.517V (vs Ag/AgCl). Meanwhile, br-GO modification resulted a significant enhancement in the total amount of extracellular electrons transferred between the modified electrode and microbe. The process of br-GO modification lowered the charge transfer resistance of the electrode and enhanced the EET. The modified electrode was further employed as an anode in the MFC, and consequently, the power density of the MFC was significantly enhanced. The current study not only gives a simple and effective way for improving the EET with br-GO fabrication, but also provides a strategy to enhance the power density of the MFC.

Oxygen-containing functional groups on bioelectrode surface enhance expression of c-type cytochromes in biofilm and boost extracellular electron transfer

Introducing oxygen-containing functional groups is a common and convenient method to increase the hydrophilicity of bioelectrodes. In this study, the effect of oxygen-containing functional groups on biofilm was systematically studied to understand how the electron transfer between electrochemically active bacteria (EAB) and bioelectrode was boosted. After electrolysis pretreatment in sulfuric and nitric acid mixture, the oxygen content of the carbon fiber brushes increased from 4.6% to 30.9%. Comparing with the control, the maximum power density increased by 27.7%, while the anode resistance decreased by 21.8%, because charge transfer resistance significantly reduced. The analysis results showed that the content of c-type cytochromes (c-Cyts) in the EAB biofilm was four times higher than that in the control, while the biomass just slightly increased and the bacteria community was similar with that of the control. These findings suggested that the fundamental reason for the enhanced extracellular electron transfer between EAB and electrode was the increased c-Cyts.

Combination of bioelectrochemical systems and electrochemical capacitors: Principles, analysis and opportunities

Bioelectrochemical systems combine electrodes and reactions driven by microorganisms for many different applications. The conversion of organic material in wastewater into electricity occurs in microbial fuel cells (MFCs). The power densities produced by MFCs are still too low for application. One way of increasing their performance is to combine them with electrochemical capacitors, widely used for charge storage purposes. Capacitive MFCs, i.e. the combination of capacitors and MFCs, allow for energy harvesting and storage and have shown to result in improved power densities, which facilitates the up scaling and application of the technology. This manuscript summarizes the state-of-the-art of combining capacitors with MFCs, starting with the theory and working principle of electrochemical capacitors. We address how different electrochemical measurements can be used to determine (bio)electrochemical capacitance and show how the measurement data can be interpreted. In addition, we present examples of the combination of electrochemical capacitors, both internal and external, that have been used to enhance MFC performance. Finally, we discuss the most promising applications and the main existing challenges for capacitive MFCs.

Shewanella oneidensis NADH dehydrogenase mutants exhibit an amino acid synthesis defect

Shewanella oneidensis MR-1 is a dissimilatory metal reducing bacterium with a highly branched respiratory electron transport chain. The S. oneidensis MR-1 genome encodes four NADH dehydrogenases, any of which may be used during respiration. We previously determined that a double-knockout of two NADH dehydrogenases, Nuo and Nqr1, eliminated aerobic growth in minimal medium. However, the double-knockout strain was able to grow aerobically in rich medium. Here, we determined that amino acid supplementation rescued growth of the mutant strain in oxic minimal medium. To determine the mechanism of the growth defect, we monitored growth, metabolism, and total NAD(H) pools in S. oneidensis MR-1 and the NADH dehydrogenase knockout strain. We also used a genetically encoded redox sensing system and determined that NADH/NAD⁺ was higher in the mutant strain than in the wild-type. We observed that the double-knockout strain was able to metabolize d,l-lactate and N-acetylglucosamine when supplemented with tryptone, but excreted high concentrations of pyruvate and acetate. The requirement for amino acid supplementation, combined with an apparent inability of the mutant strain to oxidize pyruvate or acetate suggests that TCA cycle activity was inhibited in the mutant strain by a high NADH/NAD⁺.

Reduction of Cu(II) and simultaneous production of acetate from inorganic carbon by Serratia Marcescens biofilms and plankton cells in microbial electrosynthesis systems

Simultaneous Cu(II) reduction (6.42 ± 0.02 mg/L/h), acetate production (1.13 ± 0.02 mg/L/h) from inorganic carbon (i.e., CO₂ sequestration), and hydrogen evolution (0.0315 ± 0.0005 m³/m³/d) were achieved in a Serratia marcescens Q1 catalyzed microbial electrosynthesis system (MES). The biofilms released increasing amounts of extracellular polymeric substances (EPS) with a higher compositional diversity and stronger Cu(II) complexation, compared to the plankton cells, at higher Cu(II) concentrations (up to 80 mg/L) and circuital currents (cathodic potential of -900 mV vs. standard hydrogen electrode (SHE)). Moreover, the biofilms reduced Cu(II) to Cu(0) more effectively than the plankton cells. At Cu(II) concentrations below 80 mg/L, the dehydrogenase activity in the biofilms was higher than in the plankton cells, and increased with circuital current, which was converse to the lower activities of catalase (CAT), superoxide dismutase (SOD) and antioxidative glutathione (GSH) in the biofilms than the plankton cells, although all these physiological activities were positively correlated with the concentration of Cu(II). This is the first study that evaluates the EPS constituents and the physiological activities of the biofilms and the plankton cells in the MESs, that favors the production of acetate from CO₂ sequestration and the simultaneous reduction of Cu(II) from organics-barren waters contaminated with heavy metals.

Long-Term Behavior of Defined Mixed Cultures of Geobacter sulfurreducens and Shewanella oneidensis in Bioelectrochemical Systems

This work aims to investigate the long-term behavior of interactions of electrochemically active bacteria in bioelectrochemical systems. The electrochemical performance and biofilm characteristics of pure cultures of Geobacter sulfurreducens and Shewanella oneidensis are being compared to a defined mixed culture of both organisms. While S. oneidensis pure cultures did not form cohesive and stable biofilms on graphite anodes and only yielded 0.034 ± 0.011 mA/cm² as maximum current density by feeding of each 5 mM lactate and acetate, G. sulfurreducens pure cultures formed 69 μm thick, area-wide biofilms with 10 mM acetate as initial substrate concentration and yielded a current of 0.39 ± 0.09 mA/cm². Compared to the latter, a defined mixed culture of both species was able to yield 38% higher maximum current densities of 0.54 ± 0.07 mA/cm² with each 5 mM lactate and acetate. This increase in current density was associated with a likewise increased thickness of the anodic biofilm to approximately 93 μm. It was further investigated whether a sessile incorporation of S. oneidensis into the mixed culture biofilm, which has been reported previously for short-term experiments, is long-term stable. The results demonstrate that S. oneidensis was not stably incorporated into the biofilm; rather, the planktonic presence of S. oneidensis has a positive effect on the biofilm growth of G. sulfurreducens and thus on current production.

Biodegradation of polycyclic aromatic hydrocarbons: Using microbial bioelectrochemical systems to overcome an impasse

Polycyclic aromatic hydrocarbons (PAHs) are hardly biodegradable carcinogenic organic compounds. Bioremediation is a commonly used method for treating PAH contaminated environments such as soils, sediment, water bodies and wastewater. However, bioremediation has various drawbacks including the low abundance, diversity and activity of indigenous hydrocarbon degrading bacteria, their slow growth rates and especially a limited bioavailability of PAHs in the aqueous phase. Addition of nutrients, electron acceptors or co-substrates to enhance indigenous microbial activity is costly and added chemicals often diffuse away from the target compound, thus pointing out an impasse for the bioremediation of PAHs. A promising solution is the adoption of bioelectrochemical systems. They guarantee a permanent electron supply and withdrawal for microorganisms, thereby circumventing the traditional shortcomings of bioremediation. These systems combine biological treatment with electrochemical oxidation/reduction by supplying an anode and a cathode that serve as an electron exchange facility for the biocatalyst. Here, recent achievements in polycyclic aromatic hydrocarbon removal using bioelectrochemical systems have been reviewed. This also concerns PAH precursors: total petroleum hydrocarbons and diesel. Removal performances of PAH biodegradation in bioelectrochemical systems are discussed, focussing on configurational parameters such as anode and cathode designs as well as environmental parameters like porosity, salinity, adsorption and conductivity of soil and sediment that affect PAH biodegradation in BESs. The still scarcely available information on microbiological aspects of bioelectrochemical PAH removal is summarised here. This comprehensive review offers a better understanding of the parameters that affect the removal of PAHs within bioelectrochemical systems. In addition, future experimental setups are proposed in order to study syntrophic relationships between PAH degraders and exoelectrogens. This synopsis can help as guide for researchers in their choices for future experimental designs aiming at increasing the power densities and PAH biodegradation rates using microbial bioelectrochemistry.

Electrobioremediation of oil spills

Annually, thousands of oil spills occur across the globe. As a result, petroleum substances and petrochemical compounds are widespread contaminants causing concern due to their toxicity and recalcitrance. Many remediation strategies have been developed using both physicochemical and biological approaches. Biological strategies are most benign, aiming to enhance microbial metabolic activities by supplying limiting inorganic nutrients, electron acceptors or donors, thus stimulating oxidation or reduction of contaminants. A key issue is controlling the supply of electron donors/acceptors. Bioelectrochemical systems (BES) have emerged, in which an electrical current serves as either electron donor or acceptor for oil spill bioremediation. BES are highly controllable and can possibly also serve as biosensors for real time monitoring of the degradation process. Despite being promising, multiple aspects need to be considered to make BES suitable for field applications including system design, electrode materials, operational parameters, mode of action and radius of influence. The microbiological processes, involved in bioelectrochemical contaminant degradation, are currently not fully understood, particularly in relation to electron transfer mechanisms. Especially in sulfate rich environments, the sulfur cycle appears pivotal during hydrocarbon oxidation. This review provides a comprehensive analysis of the research on bioelectrochemical remediation of oil spills and of the key parameters involved in the process.

Anode potential influences the structure and function of anodic electrode and electrolyte-associated microbiomes

Three bioelectrochemical systems were operated with set anode potentials of +300 mV, +550 mV and +800 mV vs. Standard Hydrogen Electrode (SHE) to test the hypothesis that anode potential influences microbial diversity and is positively associated with microbial biomass and activity. Bacterial and archaeal diversity was characterized using 16 S rRNA gene amplicon sequencing, and biofilm thickness was measured as a proxy for biomass. Current production and substrate utilization patterns were used as measures of microbial activity and the mid-point potentials of putative terminal oxidases were assessed using cyclic voltammetry. All measurements were performed after 4, 16, 23, 30 and 38 days. Microbial biomass and activity differed significantly between anode potentials and were lower at the highest potential. Anodic electrode and electrolyte associated community composition was also significantly influenced by anode potential. While biofilms at +800 mV were thinner, transferred less charge and oxidized less substrate than those at lower potentials, they were also associated with putative terminal oxidases with higher mid-point potentials and generated more biomass per unit charge. This indicates that microbes at +800 mV were unable to capitalize on the potential for additional energy gain due to a lack of adaptive traits to high potential solid electron acceptors and/or sensitivity to oxidative stress.

Anodic biofilms as the interphase for electroactive bacterial growth on carbon veil

The structure and activity of electrochemically active biofilms (EABs) are usually investigated on flat electrodes. However, real world applications such as wastewater treatment and bioelectrosynthesis require tridimensional electrodes to increase surface area and facilitate EAB attachment. The structure and activity of thick EABs grown on high surface area electrodes are difficult to characterize with electrochemical and microscopy methods. Here, the authors adopt a stacked electrode configuration to simulate the high surface and the tridimensional structure of an electrode for large-scale EAB applications. Each layer of the stacked electrode is independently characterized using confocal laser scanning microscopy (CLSM) and digital image processing. Shewanella oneidensis MR-1 biofilm on stacked carbon veil electrodes is grown under constant oxidative potentials (0, +200, and +400 mV versus Ag/AgCl) until a stable current output is obtained. The textural, aerial, and volumetric parameters extracted from CLSM images allow tracking of the evolution of morphological properties within the stacked electrodes. The electrode layers facing the bulk liquid show higher biovolumes compared with the inner layer of the stack. The electrochemical performance of S. oneidensis MR-1 is directly linked to the overall biofilm volume as well as connectivity between cell clusters.

Facultative nitrate reduction by electrode-respiring Geobacter metallireducens biofilms as a competitive reaction to electrode reduction in a bioelectrochemical system

Alternative metabolic options of exoelectrogenic biofilms in bioelectrochemical systems (BESs) are important not only to explain the fundamental ecology and performance of these systems but also to develop reliable integrated nutrient removal strategies in BESs, which potentially involve substrates or intermediates that support/induce those alternative metabolisms. This research focused on dissimilatory nitrate reduction as an alternative metabolism to dissimilatory anode reduction. Using the exoelectrogenic nitrate reducer Geobacter metallireducens, the critical conditions controlling those alternative metabolisms were investigated in two-chamber, potentiostatically controlled BESs at various anode potentials and biofilm thicknesses and challenged over a range of nitrate concentrations. Results showed that anode-reducing biofilms facultatively reduced nitrate at all tested anode potentials (-150 to +900 mV vs Standard Hydrogen Electrode) with a rapid metabolic shift. The critical nitrate concentration that triggered a significant decrease in BES performance was a function of anode biofilm thickness but not anode potential. This indicates that these alternative metabolisms were controlled by the availability of nitrate, which is a function of nitrate concentration in bulk solution and its diffusion into an anode-reducing biofilm. Coulombic recovery decreased as a function of nitrate dose due to electron-acceptor substrate competition, and nitrate-induced suspended biomass growth decreased the effluent quality.