Photopolymer Electrolytes for Sustainable, Upscalable, Safe, and Ambient-Temperature Sodium-Ion Secondary Batteries

Insight into ion dynamics in a NaClO4-doped polycaprolactone solid polymer electrolyte for solid state batteries

Employing low Tg polymers has fundamental limitations in providing the desirable ionic conductivity at ambient temperature due to the freezing of chain dynamics. The stiffening of polymer chains and the formation of highly ordered systems due to the crosslinks have influenced the ionic conductivity. Ionic conductivity of 1.02 × 10-5 S cm-1 was attained for the system that presented a quantum mechanical tunnelling mode of ion transport. A Na-ion transference number of 0.31 was achieved for 30 wt% of NaClO4 salt in a polycaprolactone (PCL) matrix with an electrochemical stability window of 3.6 V at 25 °C. High crystallinity and limited availability of free Na+ ions in the electrolyte have resulted in lower ionic conductivity. PCL-NaClO4 exhibited brilliant thermal stability and mechanical properties. The influence of cathode materials MnO2, V2O5 and I2 on the discharge characteristics of an electrochemical cell in the configuration cathode |(70 wt%)PCL-NaClO4(30 wt%)|Na has been studied.

Dual-Modified Electrospun Fiber Membrane as Separator with Excellent Safety Performance and High Operating Temperature for Lithium-Ion Batteries

Polyacrylonitrile/Boric acid/Melamine/the delaminated BN nanosheets electrospun fiber membrane (PB3N1BN) with excellent mechanical property, high thermal stability, superior flame-retardant performance, and good wettability are fabricated by electrospinning PAN/DMF/H3BO3/C3H6N6/ the delaminated BN nanosheets (BNNSs) homogeneous viscous suspension and followed by a heating treatment. BNNSs are obtained by delaminating the bulk h-BN in isopropyl alcohol (IPA) with an assistance of Polyvinylpyrrolidone (PVP). Benefiting from the cross-linked pore structure and high-temperature stability of BNNSs, PB3N1BN electrospun fiber membrane delivers high thermal dimensional stability (almost no size contraction at 200 °C), excellent mechanical property (19.1 MPa), good electrolyte wettability (contact angle about 0°), and excellent flame retardancy (minimum total heat release of 3.2 MJ m-2). Moreover, the assembled LiFePO4/PB3N1BN/Li asymmetrical battery using LiFePO4 as the cathode and Li as the anode has a high capacity (169 mAh g-1 at 0.5 C), exceptional rate capability (129 mAh g-1 at 5 C), the prominent cycling stability without obvious decay after 400 cycles, and a good discharge capacity of 152 mAh g-1 at a high temperature of 80 °C. This work offers a new structural design strategy toward separators with excellent mechanical performance, good wettability, and high thermal stability for lithium-ion batteries.

Revolutionizing Solid-State NASICON Sodium Batteries: Enhanced Ionic Conductivity Estimation through Multivariate Experimental Parameters Leveraging Machine Learning

Na superionic conductor (NASICON) materials hold promise as solid-state electrolytes due to their wide electrochemical stability and chemical durability. However, their limited ionic conductivity hinders their integration into sodium-ion batteries. The conventional approach to electrolyte design struggles with comprehending the intricate interactions of factors impacting conductivity, encompassing synthesis parameters, structural characteristics, and electronic descriptors. Herein, we explored the potential of machine learning in predicting ionic conductivity in NASICON. We compile a database of 211 datasets, covering 160 NASICON materials, and employ facile descriptors, including synthesis parameters, test conditions, molecular and structural attributes, and electronic properties. Random forest (RF) and neural network (NN) models were developed and optimized, with NN performing notably better, particularly with limited data (R2=0.820). Our analysis spotlighted the pivotal role of Na stoichiometric count in ionic conductivity. Furthermore, the NN algorithm highlighted the comparable significance of synthesis parameters to structural factors in determining conductivity. In contrast, the impact of electronegativity on doped elements appears less significant, underscoring the importance of dopant size and quantity. This work underscores the potential of machine learning in advancing NASICON electrolyte design for sodium-ion batteries, offering insights into conductivity drivers and a more efficient path to optimizing materials.

Ionic Conductivity and Structure of Glasses Synthesized by Mechanical-Milling Methods in the x[Na2S]-(100 - x) [0.5GeS2-0.5Ga2S3] System

Chalcogenide glasses in the Na2S-GeS2-Ga2S3 pseudoternary system were synthesized using a combination route of melt-quenching and mechanical-milling methods. First, a glass rich in germanium (90GeS2-10Ga2S3) is synthesized by melt-quenching synthesis in a silica tube sealed under vacuum. This glass is used as a precursor for the second step of mechanochemistry to explore the Na2S-GeS2-Ga2S3 pseudoternary system. By using this synthesis route, the glass-forming ability is improved as the vitreous domain is enlarged, especially for Na- and Ga-rich compositions. The as-obtained amorphous powders are characterized by Raman spectroscopy, differential scanning calorimetry, X-ray total scattering, and pair distribution function (PDF) analysis. The evolution of the Raman features observed is reproduced using density functional theory calculations. Impedance spectroscopy was performed to determine the conductivity of the new glasses. The addition of germanium sulfide to the Na2S-Ga2S3 pseudobinary system enables one to increase the conductivity by 1 order of magnitude. The highest room-temperature ionic conductivity, as measured by impedance spectroscopy, is 1.8 × 10-5 S·cm-1.

Gel Polymer Electrolytes with Talc as a Natural Mineral Filler and a Biodegradable Polymer Matrix in Sodium-Ion Batteries

A gel polymer electrolyte based on poly(vinyl alcohol) (PVA) is used in sodium-ion batteries (SIBs). The use of biodegradable and water-soluble polymer potentially reduces the negative environmental impact. The other components include sodium salt (NaPF6 ), sulfolane (TMS) as a plasticizer and talc. For the first time, natural and abundant talc has been used as an inert filler in a gel polymer electrolyte. The best results were obtained for moderate amounts of filler (1 and 3 wt%). Then, an increase in the conductivity, transference numbers, and thermal stability of the membranes was observed. Moreover, the presence of talc had a positive effect on the cyclability of the hard carbon electrode. The discharge capacity after 50 cycles of HC|1 % T_TMS|Na and HC|3 % T_TMS|Na was 243 and 225 mAh g-1 , respectively. The use of talc in gel polymer electrolytes containing sodium ions improves the safety and efficiency of SIBs.

Gel Polymer Electrolytes Design for Na-Ion Batteries

Na-ion battery has the potential to be one of the best types of next-generation energy storage devices by virtue of their cost and sustainability advantages. With the demand for high safety, the replacement of traditional organic electrolytes with polymer electrolytes can avoid electrolyte leakage and thermal instability. Polymer electrolytes, however, suffer from low ionic conductivity and large interfacial impedance. Gel polymer electrolytes (GPEs) represent an excellent balance that combines the advantages of high ionic conductivity, low interfacial impedance, high thermal stability, and flexibility. This short review summarizes the recent progress on gel polymer Na-ion batteries, focusing on different preparation approaches and the resultant physical and electrochemical properties. Reasons for the differences in ionic conductivity, mechanical properties, interfacial properties, and thermal stability are discussed at the molecular level. This Review may offer a deep understanding of sodium-ion GPEs and may guide the design of intermolecular interactions for high-performance gel polymer Na-ion batteries.

Na ion batteries: An India centric review

Developing low-cost and safe energy storage devices is the primary goal of every country to make a carbon-neutral atmosphere by ∼2050. Batteries and supercapacitors are the backbones of future sustainable energy sources for electrical vehicles (EVs), smart electronic devices, electricity supply to off-grid regions, etc. Hence, these battery-dependent devices are substantially gaining the market. Although lithium-ion batteries account for powering most of these devices, lithium availability and price pose a severe problem since lithium resources are not abundant in nature. Thus, alternative research on sodium-ion or other multi-charged cations (Al3+/Mg2+/Ca2+/K+) based energy storage devices is needed to substitute lithium-ion batteries. India and many other countries have sodium in abundance. Sodium also has potential in designing and developing efficient charge storage devices. This review article discusses the status of sodium-ion battery research activities, cost, market analysis, and future strategies of the Indian government or private bodies, industries, and research institutes of India.

Process-Structure-Formulation Interactions for Enhanced Sodium Ion Battery Development: A Review

Before the viability of a cell formulation can be assessed for implementation in commercial sodium ion batteries, processes applied in cell production should be validated and optimized. This review summarizes the steps performed in constructing sodium ion (Na-ion) cells at research scale, highlighting parameters and techniques that are likely to impact measured cycling performance. Consistent process-structure-performance links have been established for typical lithium-ion (Li-ion) cells, which can guide hypotheses to test in Na-ion cells. Liquid electrolyte viscosity, sequence of mixing electrode slurries, rate of drying electrodes and cycling characteristics of formation were found critical to the reported capacity of laboratory cells. Based on the observed importance of processing to battery performance outcomes, the current focus on novel materials in Na-ion research should be balanced with deeper investigation into mechanistic changes of cell components during and after production, to better inform future designs of these promising batteries.

A Quasi-Solid-State Tristate Reversible Electrochemical Mirror Device with Enhanced Stability

Reversible electrochemical mirror (REM) electrochromic devices with electrochemical tunability in multiple optical states are exciting alternatives to conventional electrochromic smart windows. Electrochromic devices are studied extensively, yet widespread adoptions have not been achieved due to problems associated with durability, switching speed, limited options on optical states, and cost. In this study, a REM electrochromic device based on CuSn alloy is developed, which offers highly reversible switching between transparent, greyish-blue, and mirror states via reversible electrodeposition and dissolution. The alloying element, Sn acts as an electrochemical mediator, which facilitates the electrodeposition and dissolution of Cu. The CuSn-based REM device shows superior cycling stability for 2400 cycles (transmittance mode) and 1000 cycles (reflectance mode). The electrodeposited CuSn alloy film is resistant to surface oxidation in ambient air, with a 2.9% difference in reflectance at 2000 nm after 3 days. In addition, the alloy film exhibits excellent NIR reflectance property with thermal modulation of 18.5 °C at a high temperature of 180 °C. The REM device with zero power consumption maintains its mirror state for at least 100 min, making it a promising candidate for energy-efficient applications.

Building Better Batteries in the Solid State: A Review

Most of the current commercialized lithium batteries employ liquid electrolytes, despite their vulnerability to battery fire hazards, because they avoid the formation of dendrites on the anode side, which is commonly encountered in solid-state batteries. In a review two years ago, we focused on the challenges and issues facing lithium metal for solid-state rechargeable batteries, pointed to the progress made in addressing this drawback, and concluded that a situation could be envisioned where solid-state batteries would again win over liquid batteries for different applications in the near future. However, an additional drawback of solid-state batteries is the lower ionic conductivity of the electrolyte. Therefore, extensive research efforts have been invested in the last few years to overcome this problem, the reward of which has been significant progress. It is the purpose of this review to report these recent works and the state of the art on solid electrolytes. In addition to solid electrolytes stricto sensu, there are other electrolytes that are mainly solids, but with some added liquid. In some cases, the amount of liquid added is only on the microliter scale; the addition of liquid is aimed at only improving the contact between a solid-state electrolyte and an electrode, for instance. In some other cases, the amount of liquid is larger, as in the case of gel polymers. It is also an acceptable solution if the amount of liquid is small enough to maintain the safety of the cell; such cases are also considered in this review. Different chemistries are examined, including not only Li-air, Li-O2, and Li-S, but also sodium-ion batteries, which are also subject to intensive research. The challenges toward commercialization are also considered.

Thermoplastic Polyurethane Elastomer-Based Gel Polymer Electrolytes for Sodium-Metal Cells with Enhanced Cycling Performance

Sodium batteries have been recognized as a promising alternative to lithium-ion batteries. However, the liquid electrolyte used in these batteries has inherent safety problems. Polymer electrolytes have been considered as safer and more reliable electrolyte systems for rechargeable batteries. Herein, a thermoplastic polyurethane elastomer-based gel polymer electrolyte with high ionic conductivity and high elasticity was reported. It had an ambient-temperature ionic conductivity of 1.5 mS cm^-1 and high stretchability, capable of withstanding 610 % strain. Coordination between Na⁺ ions and polymer chains increased the degree of salt dissociation in the gel polymer electrolyte compared with the liquid electrolyte. An Na/Na₃ V₂ (PO₄ )₃ cell assembled with gel polymer electrolyte exhibited good cycling performance in terms of discharge capacity, cycling stability, and rate capability, which was owing to the effective trapping ability of organic solvents in the polymer matrix and uniform flux of sodium ions through the gel polymer electrolyte.

Electrolytes and Electrolyte/Electrode Interfaces in Sodium-Ion Batteries: From Scientific Research to Practical Application

Sodium-ion batteries (SIBs) have drawn considerable interest as power-storage devices owing to the wide abundance of their constituents and low cost. To realize a high performance-price ratio, the cathode and anode materials must be optimized. As essential components of SIBs, electrolytes should have wide electrochemical windows, high thermal stability, and exceptional ionic conductivity. Therefore, improved electrolytes, based on various materials and compositions, are developed to meet the practical demands of SIBs, including organic electrolytes, ionic liquids, aqueous, solid electrolytes, and hybrid electrolytes. Although mature organic electrolytes are currently used in production, aqueous and solid electrolytes show advantages for future applications, as discussed here in detail. Current efforts in modifying electrolytes to optimize their interfacial compatibility with electrodes, leading to longer battery lifetimes and greater safety, are described. The advanced characterization techniques used to investigate the properties of electrolytes and interfaces are introduced, and the reaction processes and degradation mechanisms of SIBs are revealed. Furthermore, the practical prospects of SIBs promoted by high-quality electrolytes appropriately matched with electrodes are predicted and directions for developing next-generation SIBs are suggested.

A Bifunctional Fluorophosphate Electrolyte for Safer Sodium-Ion Batteries

Most of the currently developed sodium-ion batteries (SIBs) have potential safety hazards due to the use of highly volatile and flammable alkyl carbonate electrolytes. To overcome this challenge, we report an electrochemically compatible and nonflammable electrolyte, tris(2,2,2-trifluoroethyl) phosphate (TFEP) with low-concentration sodium bis(fluorosulfonyl)imide (0.9 M), which is designed not only to match perfectly with the hard carbon (HC) anode but also to enhance the thermal stability of SIBs. Experimental results and theoretical calculations reveal that TFEP molecules have a significantly low barrier to decompose before Na+ inserts into HC, forming a stable inorganic solid-electrolyte interface layer, thus improving the electrochemical and structural stabilities of HC anodes. An HC/Na3V2(PO4)3 full cell using TFEP electrolyte shows a high capacity retention of 89.2% after 300 cycles and a dramatically reduced exothermic heat at elevated temperature, implying its potential application for safe and low-cost larger-scale energy storage.

Synthesis and physicochemical characterization of room temperature ionic liquids and their application in sodium ion batteries

Sodium ion batteries (SIBs) based on IL electrolytes have attracted great attention, particularly in large-scale energy storage systems for renewable energy due to the abundance of sodium and the excellent safety resulting from the use of non-flammable ionic liquid (IL) electrolytes. In this article, a series of 15 functionalized room temperature ionic liquids (RTILs) suitable as electrolytes is presented. Special emphasis was laid on the purity of the synthesized RTILs and a consistent and uniform characterization of their physicochemical properties. Evaluation of the viscosity, conductivity, and thermal and electrochemical stabilities resulted in clear structure-property relationships, rendering the ether functionalized RTILs most promising for application in SIBs. Electrochemical investigations of the ether functionalized IL electrolytes in SIB half cells (Na0.6Mn0.9Co0.1O2 as cathode material) proved their compatibility with a SIB system. Stable cycling performance was achieved with the piperidinium based RTIL IL 6 outperforming the organic electrolyte by far with a retention of 81% after 350 cycles. These results show the suitability of RTILs to enhance the performance of SIB systems and serve as a basis for the design of high performance IL electrolytes.

Thermal Mapping of a Lithium Polymer Batteries Pack with FBGs Network

In this paper, a network of 37 fiber Bragg grating (FBG) sensors is proposed for real-time, in situ, and operando multipoint monitoring of the surface temperature distribution on a pack of three prismatic lithium polymer batteries (LiPBs). Using the network, a spatial and temporal thermal mapping of all pack interfaces was performed. In each interface, nine strategic locations were monitored by considering a three-by-three matrix, corresponding to the LiPBs top, middle and bottom zones. The batteries were subjected to charge and discharge cycles, where the charge was carried out at 1.0 C, whereas the discharge rates were 0.7 C and 1.4 C. The results show that in general, a thermal gradient is recognized from the top to the bottom, but is less prominent in the end-of-charge steps. The results also indicate the presence of hot spots between two of the three batteries, which were located near the positive tab collector. This occurs due to the higher current density of the lithium ions in this area. The presented FBG sensing network can be used to improve the thermal management of batteries by performing a spatiotemporal thermal mapping, as well as by identifying the zones which are more conducive to the possibility of the existence of hot spots, thereby preventing severe consequences such as thermal runaway and promoting their safety. To our knowledge, this is the first time that a spatial and temporal thermal mapping is reported for this specific application using a network of FBG sensors.

Fabrication of PEO-PMMA-LiClO4-Based Solid Polymer Electrolytes Containing Silica Aerogel Particles for All-Solid-State Lithium Batteries

To improve the ionic conductivity and thermal stability of a polyethylene oxide (PEO)-ethylene carbonate (EC)-LiClO4-based solid polymer electrolyte for lithium-ion batteries, polymethyl methacrylate (PMMA) and silica aerogel were incorporated into the PEO matrix. The effects of the PEO:PMMA molar ratio and the amount of silica aerogel on the structure of the PEO-PMMA-LiClO4 solid polymer electrolyte were studied by X-ray diffraction, Fourier-transform infrared spectroscopy and alternating current (AC) impedance measurements. The solid polymer electrolyte with PEO:PMMA = 8:1 and 8 wt% silica aerogel exhibited the highest lithium-ion conductivity (1.35 × 10−4 S∙cm−1 at 30 °C) and good mechanical stability. The enhanced amorphous character and high degree of dissociation of the LiClO4 salt were responsible for the high lithium-ion conductivity observed. Silica aerogels with a high specific surface area and mesoporosity could thus play an important role in the development of solid polymer electrolytes with improved structure and stability.

Pairing of Luminescent Switch with Electrochromism for Quasi-Solid-State Dual-Function Smart Windows

Smart window is a promising green technology with feature of tunable transparency under external stimuli to manage light transmission and solar energy. However, more functions based on the intelligent management of the solar spectrum need to be integrated into present smart windows. In this work, a dual-function smart window is fabricated by pairing the luminescent switch with the electrochromic window. The dual function is based on a single fluorine doped tin oxide coated glass functionalized with tungsten oxide and copper nanocluster, among which tungsten oxide serves as an electrochromic material and copper nanocluster provides photoinduced luminescence. Along with the regulation of the visible light based on the electrochromism of the window, the luminescence can be finely switched on and off, which establishes a pair of reversible states ("on" and "off") for the dual-function smart window. The contrast between two states reaches 88%. Furthermore, the manipulation of dual-function smart window is highly reversible with a short response time of 12.6 s. This prototype of dual-function smart window paves the way for developing multifunctional smart windows by integrating different functional materials into one smart window based on the rational management of the solar spectrum.

Combined Structural, Chemometric, and Electrochemical Investigation of Vertically Aligned TiO2 Nanotubes for Na-ion Batteries

In the challenging scenario of anode materials for sodium-ion batteries, TiO2 nanotubes could represent a winning choice in terms of cost, scalability of the preparation procedure, and long-term stability upon reversible operation in electrochemical cells. In this work, a detailed physicochemical, computational, and electrochemical characterization is carried out on TiO2 nanotubes synthesized by varying growth time and heat treatment, viz. the two most significant experimental parameters during preparation. A chemometric approach is proposed to obtain a concrete and solid multivariate analysis of sodium battery electrode materials. Such a statistical approach, combined with prolonged galvanostatic cycling and density functional theory analysis, allows identifying anatase at high growth time as the TiO2 polymorph of choice as an anode material, thus creating a benchmark for sodium-ion batteries, which currently took the center stage of the research in the field of energy storage systems from renewables.

In Situ Formation of Polysulfonamide Supported Poly(ethylene glycol) Divinyl Ether Based Polymer Electrolyte toward Monolithic Sodium Ion Batteries

Sodium ion battery is one of the promising rechargeable batteries due to the low-cost and abundant sodium sources. In this work, a monolithic sodium ion battery based on a Na₃ V₂ (PO₄ )₃ cathode, MoS₂ layered anode, and polyether-based polymer electrolyte is reported. In addition, a new kind of polysulfonamide-supported poly(ethylene glycol) divinyl ether based polymer electrolyte is also demonstrated for monolithic sodium ion battery via in situ preparation. The resultant polymer electrolyte exhibits relatively high ionic conductivity (1.2 mS cm^-1 ) at ambient temperature, wide electrochemical window (4.7 V), and favorable mechanical strength (25 MPa). Moreover, such a monolithic Na₃ V₂ (PO₄ )₃ /MoS₂ sodium ion battery using this polymer electrolyte delivers outstanding rate capability (up to 10 C) and superior cyclic stability (84%) after 1000 cycles at 0.5 C. What is more essential, such a polymer electrolyte based soft-package monolithic sodium ion cell can still power a red light emitting diode lamp and run finite times without suffering from any internal short-circuit failures, even in the case of a bended and wrinkled state. Considering these aspects, this work no doubt provides a new approach for the design of a high-performance polymer electrolyte toward monolithic sodium ion battery with exceptional rate capability and high safety.