From the Synthesis of Biobased Cyclic Carbonate to Polyhydroxyurethanes: A Promising Route towards Renewable Non-Isocyanate Polyurethanes

Controlling Hybrid Polyhydroxyurethane Adhesive and Rheological Properties by Partial Carbonation of Biobased Epoxy Monomer

Controlling hybrid material properties by simple monomer design offers an elegant pathway to prepare thermoset adhesives with tunable properties. Herein, biobased hybrid polyhydroxyurethane/polyepoxy is prepared starting from partially carbonated cashew nut shell epoxy derivatives (NC514) and m-xylene diamine (MXDA). The curing reactions, that is, epoxy-amine and cyclic carbonate aminolysis, monitored by ATR-IR spectroscopy at 50 °C are found to be concomitant yielding highly homogeneous materials. Hybrid networks are extensively characterized by swelling tests, TGA, DMA, DSC, tensile tests, rheology, and lap-shear-test on aluminum substrates. The introduction of hydroxyurethane moieties within the epoxy-amine networks enhanced the adhesion properties (up to 20% compare to neat epoxy resins) by combining hydrogen bonding capability and vitrimeric properties (thermoset able to flow). Rheological characterizations and reprocessing tests demonstrated that hybrid adhesives with up to 47 mol% of cyclic carbonate groups are capable of covalent exchange (internally catalyzed by tertiary amine) while keeping similar thermomechanical properties and enhanced adhesion strength compare to the permanent epoxy network.

Harnessing Enhanced Flame Retardancy in Rigid Polyurethane Composite Foams through Hemp Seed Oil-Derived Natural Fillers

Over the past few decades, polymer composites have received significant interest and become protagonists due to their enhanced properties and wide range of applications. Herein, we examined the impact of filler and flame retardants in hemp seed oil-based rigid polyurethane foam (RPUF) composites' performance. Firstly, the hemp seed oil (HSO) was converted to a corresponding epoxy analog, followed by a ring-opening reaction to synthesize hemp bio-polyols. The hemp polyol was then reacted with diisocyanate in the presence of commercial polyols and other foaming components to produce RPUF in a single step. In addition, different fillers like microcrystalline cellulose, alkaline lignin, titanium dioxide, and melamine (as a flame retardant) were used in different wt.% ratios to fabricate composite foam. The mechanical characteristics, thermal degradation behavior, cellular morphology, apparent density, flammability, and closed-cell contents of the generated composite foams were examined. An initial screening of different fillers revealed that microcrystalline cellulose significantly improves the mechanical strength up to 318 kPa. The effect of melamine as a flame retardant in composite foam was also examined, which shows the highest compression strength of 447 kPa. Significantly better anti-flaming qualities than those of neat foam based on HSO have been reflected using 22.15 wt.% of melamine, with the lowest burning time of 4.1 s and weight loss of 1.88 wt.%. All the composite foams showed about 90% closed-cell content. The present work illustrates the assembly of a filler-based polyurethane foam composite with anti-flaming properties from bio-based feedstocks with high-performance applications.

Physicochemical and Mechanical Properties of Non-Isocyanate Polyhydroxyurethanes (NIPHUs) from Epoxidized Soybean Oil: Candidates for Wound Dressing Applications

Only 0.1% of polyurethanes available on the market are from renewable sources. With increasing concern about climate change, the substitution of monomers derived from petrochemical sources and the application of eco-friendly synthesis processes is crucial for the development of biomaterials. Therefore, polyhydroxyurethanes have been utilized, as their synthesis route allows for the carbonation of vegetable oils with carbon dioxide and the substitution of isocyanates known for their high toxicity, carcinogenicity, and petrochemical origin. In this study, polyhydroxyurethanes were obtained from carbonated soybean oil in combination with two diamines, one that is aliphatic (1,4-butadiamine (putrescine)) and another that is cycloaliphatic (1,3-cyclohexanobis(methylamine)). Four polyhydroxyurethanes were obtained, showing stability in hydrolytic and oxidative media, thermal stability above 200 °C, tensile strength between 0.9 and 1.1 MPa, an elongation at break between 81 and 222%, a water absorption rate up 102%, and contact angles between 63.70 and 101.39. New formulations of bio-based NIPHUs can be developed with the inclusion of a cycloaliphatic diamine (CHM) for the improvement of mechanical properties, which represents a more sustainable process for obtaining NIPHUs with the physicochemical, mechanical, and thermal properties required for the preparation of wound dressings.

Cholinium Pyridinolate Ionic Pair-Catalyzed Fixation of CO2 into Cyclic Carbonates

A halide-free ionic pair organocatalyst was proposed for the cycloaddition of CO2 into epoxide reactions. Cholinium pyridinolate ionic pairs with three different substitution positions were designed. Under conditions of temperature of 120 °C, pressure of 1 MPa CO2, and catalyst loading of 5 mol %, the optimal catalyst cholinium 4-pyridinolate ([Ch]+[4-OP]-) was employed. After a reaction time of 12 h, styrene oxide was successfully converted into the corresponding cyclic carbonate, and its selectivity was improved to 90%. A series of terminal epoxides were converted into cyclic carbonates within 12 h, with yields ranging from 80 to 99%. The proposed mechanism was verified by 1H NMR and 13C NMR titrations. Cholinium cations act as a hydrogen bond donor to activate epoxides, and pyridinolate anions combine with carbon dioxide to form intermediate carbonate anions that attack epoxides as nucleophiles and lead to ring opening. In summary, a halide-free ionic pair organocatalyst was designed and the catalytic mechanism in the cycloaddition of CO2 into epoxides reactions was proposed.

Catalytic Strategies for the Cycloaddition of CO2 to Epoxides in Aqueous Media to Enhance the Activity and Recyclability of Molecular Organocatalysts

The cycloaddition of CO2 to epoxides to afford versatile and useful cyclic carbonate compounds is a highly investigated method for the nonreductive upcycling of CO2. One of the main focuses of the current research in this area is the discovery of readily available, sustainable, and inexpensive catalysts, and of catalytic methodologies that allow their seamless solvent-free recycling. Water, often regarded as an undesirable pollutant in the cycloaddition process, is progressively emerging as a helpful reaction component. On the one hand, it serves as an inexpensive hydrogen bond donor (HBD) to enhance the performance of ionic compounds; on the other hand, aqueous media allow the development of diverse catalytic protocols that can boost catalytic performance or ease the recycling of molecular catalysts. An overview of the advances in the use of aqueous and biphasic aqueous systems for the cycloaddition of CO2 to epoxides is provided in this work along with recommendations for possible future developments.

Preparation of Non-Isocyanate Polyurethanes from Mixed Cyclic-Carbonated Compounds: Soybean Oil and CO2-Based Poly(ether carbonate)

This study presents the synthesis and characterization of non-isocyanate polyurethanes (NIPU) derived from the copolymerization of cyclic-carbonated soybean oil (CSBO) and cyclic carbonate (CC)-terminated poly(ether carbonate) (RCC). Using a double-metal cyanide catalyst, poly(ether carbonate) polyol was first synthesized through the copolymerization of carbon dioxide and propylene oxide. The terminal hydroxyl group was then subjected to a substitution reaction with a five-membered CC group using glycerol-1,2-carbonate and oxalyl chloride, yielding RCC. Attempts to prepare NIPU solely using RCC and diamine were unsuccessful, possibly due to the low CC functionality and the aminolysis of RCC's linear carbonate repeating units. However, when combined with CSBO, solid NIPUs were successfully obtained, exhibiting good thermal stability along with enhanced mechanical properties compared to conventional CSBO-based NIPU formulations. Overall, this study underscores the potential of leveraging renewable resources and carbon capture technologies to develop sustainable NIPUs with tailored properties, thereby expanding their range of applications.

CO2 Valorization in Deep Eutectic Solvents

The deep eutectic solvent (DES) has emerged in recent years as a valuable medium for converting CO2 into valuable chemicals because of its easy availability, stability, and safety, and its capability to dissolve carbon dioxide. CO2 valorization in DES has evolved rapidly over the past 20 years. As well as being used as solvents for acid/base-promoted CO2 conversion for the production of cyclic carbonates and carbamates, DESs can be used as reaction media for electrochemical CO2 reduction for formic acid and CO. Among these products, cyclic carbonates can be used as solvents and electrolytes, carbamate derivatives include the core structure of many herbicides and pesticides, and formic acid and carbon monoxide, the C1 electrochemical products, are essential raw materials in the chemical industries. An overview of the application of DESs for CO2 valorization in recent years is presented in this review, followed by a compilation and comparison of product types and reaction mechanisms within the different types of DESs, and an outlook on how CO2 valorization will be developed in the future.

A review on vegetable oil-based non isocyanate polyurethane: towards a greener and sustainable production route

The transition from conventional polyurethane (PU) to non isocyanate polyurethane (NIPU) is driven mainly by safety concerns, environmental considerations, and sustainability issues associated with the current PU technology. NIPU has emerged as a promising alternative, addressing limitations related to traditional PU production. There has been increasing interest in bio-based NIPU aligning with the aspiration for green materials and processes. One important biomass resource for the development of bio-based NIPU is vegetable oil, an abundant, renewable, and relatively low cost feedstock. As such, this review aims to provide insight into the progression of NIPU derived from vegetable oils. This article highlights the synthetic and green approach to NIPU production, emphasizing the method involving the polyaddition reaction of cyclic carbonates and amines. The review includes case studies on vegetable oil-based NIPU and perspectives on their properties. Further, discussions on the potential applications and commercial importance of PU and NIPU are included. Finally, we offer perspectives on possible research directions and the future prospects of NIPU, contributing to the ongoing evolution of PU technology.

Unique Method for Facile Postsynthetic Modification of Nonisocyanate Polyurethanes

Nonisocyanate polyurethanes (NIPUs) are broadly investigated as a potential replacement for conventional polyurethanes (PUs) to eliminate the use of toxic isocyanates and reduce occupational hazards. One of the most popular approaches to NIPU synthesis is the polyaddition of cyclic bis(carbonate)s and diamines to form poly(hydroxyurethane)s (PHUs). However, such PHUs are highly hydrophilic due to the presence of two hydroxyl groups per repeat unit, and the resulting moisture absorption significantly degrades their thermomechanical performance and physical stability upon exposure to humidity, thus limiting their utility. Here, we introduce a simple and scalable approach for the modification of PHUs to increase hydrophobicity and adjust their properties. The proposed reaction between aldehydes and appropriately spaced hydroxyl groups in the polymer backbone resulted in high degrees of modification (up to 84%) and up to 3-fold reductions in water uptake at 85% RH. Furthermore, the use of aromatic aldehydes in particular enabled the retention of mechanical properties over a wide range of humidity levels, resulting in performance comparable to conventional PUs. Finally, we note that this approach is not limited to reducing moisture sensitivity alone and provides ample opportunities for imparting a broad range of novel properties to PHUs through an appropriate selection of functional aldehydes.

Intensified Continuous Flow Process for the Scalable Production of Bio-Based Glycerol Carbonate

A subtle combination of fundamental and applied organic chemistry toward process intensification is demonstrated for the large-scale production of bio-based glycerol carbonate under flow conditions. The direct carbonation of bio-based glycidol with CO2 is successfully carried out under intensified flow conditions, with Barton's base as a potent homogeneous organocatalyst. Process metrics for the CO2 coupling step (for the upstream production, output: 3.6 kg day-1 , Space Time Yield (STY): 2.7 kg h-1  L-1 , Environmental factor (E-factor): 4.7) outclass previous reports. High conversion and selectivity are achieved in less than 30 s of residence time at pilot scale with a stoichiometric amount of CO2 . Supporting DFT computations reveal the unique features of the mechanism in presence of Brønsted bases.

Polyhydroxyurethane and Poly(ethylene oxide) Multiblock Copolymer Networks: Crosslinking with Polysilsesquioxane, Reprocessing and Solid Polyelectrolyte Properties

This contribution reports the synthesis of polyhydroxyurethane (PHU)-poly(ethylene oxide) (PEO) multiblock copolymer networks crosslinked with polysilsesquioxane (PSSQ). First, the linear PHU-PEO multiblock copolymers were synthesized via the step-growth polymerization of bis(6-membered cyclic carbonate) (B6CC) with α,ω-diamino-terminated PEOs with variable molecular weights. Thereafter, the PHU-PEO copolymers were allowed to react with 3-isocyanatopropyltriethoxysilane (IPTS) to afford the derivatives bearing triethoxysilane moieties, the hydrolysis and condensation of which afforded the PHU-PEO networks crosslinked with PSSQ. It was found that the PHU-PEO networks displayed excellent reprocessing properties in the presence of trifluoromethanesulfonate [Zn(OTf)2]. Compared to the PHU networks crosslinked via the reaction of difunctional cyclic carbonate with multifunctional amines, the organic-inorganic PHU networks displayed the decreased reprocessing temperature. The metathesis of silyl ether bonds is responsible for the improved reprocessing behavior. By adding lithium trifluoromethanesulfonate (LiOTf), the PHU-PEO networks were further transformed into the solid polymer electrolytes. It was found that the crystallization of PEO chains in the crosslinked networks was significantly suppressed. The solid polymer electrolytes had the ionic conductivity as high as 7.64 × 10-5 S × cm-1 at 300 K. More importantly, the solid polymer electrolytes were recyclable; the reprocessing did not affect the ionic conductivity.

Innovations in applications and prospects of non-isocyanate polyurethane bioplastics

Currently, conventional plastics are necessary for a variety of aspects of modern daily life, including applications in the fields of healthcare, technology, and construction. However, they could also contain potentially hazardous compounds like isocyanates, whose degradation has a negative impact on both the environment and human health. Therefore, researchers are exploring alternatives to plastic which is sustainable and environmentally friendly without compromising its mechanical and physical features. This review study highlights the production of highly eco-friendly bioplastic as an efficient alternative to non-biodegradable conventional plastic. Bioplastics are produced from various renewable biomass sources such as plant debris, fatty acids, and oils. Poly-addition of di-isocyanates and polyols is a technique employed over decades to produce polyurethanes (PUs) bioplastics from renewable biomass feedstock. The toxicity of isocyanates is a major concern with the above-mentioned approach. Novel green synthetic approaches for polyurethanes without using isocyanates have been attracting greater interest in recent years to overcome the toxicity of isocyanate-containing raw materials. The polyaddition of cyclic carbonates (CCs) and polyfunctional amines appears to be the most promising method to obtain non-isocyanate polyurethanes (NIPUs). This method results in the creation of polymeric materials with distinctive and adaptable features with the elimination of harmful compounds. Consequently, non-isocyanate polyurethanes represent a new class of green polymeric materials. In this review study, we have discussed the possibility of creating novel NIPUs from renewable feedstocks in the context of the growing demand for efficient and ecologically friendly plastic products.

Facile and Efficient Production of Biomass-Derived Isosorbide Dioxides via Epoxidation Using In situ-generated DMDO under Ultrasonication

Herein, we present a facile synthetic process for producing biomass-derived isosorbide (ISB) dioxides using dimethyl dioxirane (DMDO) as an efficient oxidizing agent, which was generated in situ from acetone and KHSO5 . To achieve high conversion and product yield, the KHSO5 concentration, KHSO5 flow rate, and reaction temperature were optimized. Under the optimal conditions, rapid and efficient epoxidation using the in situ-generated DMDO was observed under ultrasonication, yielding the desired product within 35 min at 0 °C. This study offers a convenient and efficient method for generating biomass-derived ISB building blocks, which have significant potential for the fabrication of bioplastics.

An Advanced Review: Polyurethane-Related Dressings for Skin Wound Repair

The inability of wounds to heal effectively through normal repair has become a burden that seriously affects socio-economic development and human health. The therapy of acute and chronic skin wounds still poses great clinical difficulty due to the lack of suitable functional wound dressings. It has been found that dressings made of polyurethane exhibit excellent and diverse biological properties, but lack the functionality of clinical needs, and most dressings are unable to dynamically adapt to microenvironmental changes during the healing process at different stages of chronic wounds. Therefore, the development of multifunctional polyurethane composite materials has become a hot topic of research. This review describes the changes in physicochemical and biological properties caused by the incorporation of different polymers and fillers into polyurethane dressings and describes their applications in wound repair and regeneration. We listed several polymers, mainly including natural-based polymers (e.g., collagen, chitosan, and hyaluronic acid), synthetic-based polymers (e.g., polyethylene glycol, polyvinyl alcohol, and polyacrylamide), and some other active ingredients (e.g., LL37 peptide, platelet lysate, and exosomes). In addition to an introduction to the design and application of polyurethane-related dressings, we discuss the conversion and use of advanced functional dressings for applications, as well as future directions for development, providing reference for the development and new applications of novel polyurethane dressings.

Latest Advancements in the Development of High-Performance Lignin- and Tannin-Based Non-Isocyanate Polyurethane Adhesive for Wood Composites

The depletion of natural resources and increasing environmental apprehension regarding the reduction of harmful isocyanates employed in manufacturing polyurethanes (PUs) have generated significant attention from both industrial and academic sectors. This attention is focused on advancing bio-based non-isocyanate polyurethane (NIPU) resins as viable and sustainable substitutes, possessing satisfactory properties. This review presents a comprehensive analysis of the progress made in developing bio-based NIPU polymers for wood adhesive applications. The main aim of this paper is to conduct a comprehensive analysis of the latest advancements in the production of high-performance bio-based NIPU resins derived from lignin and tannin for wood composites. A comprehensive evaluation was conducted on scholarly publications retrieved from the Scopus database, encompassing the period from January 2010 to April 2023. In NIPU adhesive manufacturing, the exploration of substitute materials for isocyanates is imperative, due to their inherent toxicity, high cost, and limited availability. The process of demethylation and carbonation of lignin and tannin has the potential to produce polyphenolic compounds that possess hydroxyl and carbonyl functional groups. Bio-based NIPUs can be synthesized through the reaction involving diamine molecules. Previous studies have provided evidence indicating that NIPUs derived from lignin and tannin exhibit enhanced mechanical properties, decreased curing temperatures and shortened pressing durations, and are devoid of isocyanates. The characterization of NIPU adhesives based on lignin and tannin was conducted using various analytical techniques, including Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), matrix-assisted laser desorption/ionization with time-of-flight (MALDI-TOF) mass spectrometry, and gel permeation chromatography (GPC). The adhesive performance of tannin-based NIPU resins was shown to be superior to that of lignin-based NIPUs. This paper elucidates the potential of lignin and tannin as alternate sources for polyols in the manufacturing of NIPUs, specifically for their application as wood adhesives.

Dynamic PEG-PLA/Hydroxyurethane Networks Based on Imine Bonds as Reprocessable Elastomeric Biomaterials

The development of dynamic covalent chemistry opens the way to the design of materials able to be reprocessed by an internal exchange reaction under thermal stimulus. Imine exchange differs from other exchange reactions by its relatively low temperature of activation. In this study, amine-functionalized star-shaped PEG-PLA and an aldehyde-functionalized hydroxyurethane modifier were combined to produce PEG-PLA/hydroxyurethane networks incorporating imine bonds. The thermal and mechanical properties of these new materials were evaluated as a function of the initial ratio of amine/aldehyde used during synthesis. Rheological analyses highlighted the dynamic behavior of these vitrimers at moderate temperature (60-85 °C) and provided the flow activation energies. Additionally, the reprocessability of these PEG-PLA/hydroxyurethane vitrimers was assessed by comparing the material properties before reshaping and after three reprocessing cycles (1 ton, 1 h, 70 °C). Hence, these materials can easily be designed to satisfy a specific medical application without properties loss. This work opens the way to the development of a new generation of dynamic materials combining degradable PEG-PLA copolymers and hydroxyurethane modifiers, which could find applications in the shape of medical devices on-demand under mild conditions.

Approach to Circular Chemistry Preparing New Polyesters from Olive Oil

The transformation of cooking oils and their waste into polyesters is a challenge for circular chemistry. Herein, we have used epoxidized olive oil (EOO), obtained from cooking olive oil (COO), and various cyclic anhydrides (such as phthalic anhydride PA, maleic anhydride MA, and succinic anhydride SA) as raw materials for the preparation of new bio-based polyesters. For the synthesis of these materials, we have used the bis(guanidine) organocatalyst 1 and tetrabutylammonium iodide (Bu₄NI) as cocatalyst. The optimal reaction conditions for the preparation of poly(EOO-co-PA) and poly(EOO-co-MA) were 80 °C for 5 h using toluene as solvent; however, the synthesis of poly(EOO-co-SA) required more extreme reaction conditions. Furthermore, we have exclusively succeeded in obtaining the trans isomer for MA-polyester. The obtained biopolyesters were characterized by NMR, Fourier transform infrared, thermogravimetric analysis, and scanning electron microscopy analyses. Since there are few examples of functionalized and defined compounds based on olive oil, it is innovative and challenging to transform these natural-based compounds into products with high added value.

Evaluation of Lactobacillus plantarum and PRGF as a new bioactive multi-layered scaffold PU/PRGF/gelatin/PU for wound healing

The effect of tissue engineering strategies in combination with Lactobacillus plantarum and platelet-rich growth factor (PRGF) with the aim of creating an appropriate wound dressing can be useful in wound healing and infection prevention in patients suffering from acute and chronic skin damages. Therefore, in this study, a new approach was employed to create a bioactive multilayer electrospun scaffold composed of polyurethane (PU), PRGF, and gelatin fibers, then human adipose-derived mesenchymal stem cells (hAMSCs), fibroblast cells (HU-02) and L. plantarum were cultured on the scaffold. The physicochemical properties, biocompatibility, and antibacterial activity of the scaffold were evaluated. In addition, the expression of the migration and proliferation genes of fibroblast cells were investigated by real-time PCR (polymerase chain reaction). Mitochondrial activity assays revealed that PRFG and L. plantarum had a significant positive effect on the viability of target co-cultured cells.Fluorescent and SEM (scanning electron microscopy) images presented the cells and bacterial proliferation and adhesion in hydrophilic scaffolds within 21 days. The sustained release of PRGF from scaffolds with a zero-order pattern was confirmed. RT-PCR analysis revealed that PRGF elevated the expression of VEGF genes up to fourfold, but L. plantarum had a better effect on DDR2 gene expression compared to the TCPS group. Antibacterial tests showed that L. plantarum has a bacterial load reduction of more than 70% in CFU/mL. The present scaffold is an appropriate model for cell attachment, migration, proliferation, and infection prevention.

Tailor-Made Bio-Based Non-Isocyanate Polyurethanes (NIPUs)

Non-isocyanate polyurethanes (NIPUs) based on biobased polyamines and polycarbonates are a sustainable alternative to conventional polyurethanes (PU). This article discloses a novel method to control the crosslinking density of fully biobased isocyanate-free polyurethanes, synthesized from triglycerides carbonated previously in scCO₂ and different diamines, such as ethylenediamine (EDA), hexamethylenediamine (HMDA) and Priamine^TM-1075 (derived from a dimerized fatty acid). As capping substances, water or bioalcohols are used in such a way that the crosslinking density can be adjusted to suit the requirements of the intended application. An optimization of the NIPU synthesis procedure is firstly carried out, establishing the polymerization kinetics and proposing optimal conditions set for the synthesis of the NIPUs. Then, the influence of the partial blocking of the active polymerization sites of the carbonated soybean oil (CSBO), using monofunctional amines, on the physical properties of the NIPUS is explored. Finally, the synthesis of fully biobased NIPUs with a targeted crosslinking density is achieved using hybrid NIPUs, employing partially carbonated oil and H₂O or ethanol as blockers to achieve the desired physical properties in a very precise manner.

End-of-life upcycling of polyurethanes using a room temperature, mechanism-based degradation

A major challenge in developing recyclable polymeric materials is the inherent conflict between the properties required during and after their life span. In particular, materials must be strong and durable when in use, but undergo complete and rapid degradation, ideally under mild conditions, as they approach the end of their life span. We report a mechanism for degrading polymers called cyclization-triggered chain cleavage (CATCH cleavage) that achieves this duality. CATCH cleavage features a simple glycerol-based acyclic acetal unit as a kinetic and thermodynamic trap for gated chain shattering. Thus, an organic acid induces transient chain breaks with oxocarbenium ion formation and subsequent intramolecular cyclization to fully depolymerize the polymer backbone at room temperature. With minimal chemical modification, the resulting degradation products from a polyurethane elastomer can be repurposed into strong adhesives and photochromic coatings, demonstrating the potential for upcycling. The CATCH cleavage strategy for low-energy input breakdown and subsequent upcycling may be generalizable to a broader range of synthetic polymers and their end-of-life waste streams.

Recent Advancements in Polyurethane-based Tissue Engineering

In tissue engineering, polyurethane-based implants have gained significant traction because of their high compatibility and inertness. The implants therefore show fewer side effects and lasts longer. Also, the mechanical properties can be tuned and morphed into a particular shape, owing to which polyurethanes show immense versatility. In the last 3 years, scientists have devised methods to enhance the strength of and induce dynamic properties in polyurethanes, and these developments offer an immense opportunity to use them in tissue engineering. The focus of this review is on applications of polyurethane implants for biomedical application with detailed analysis of hard tissue implants like bone tissues and soft tissues like cartilage, muscles, skeletal tissues, and blood vessels. The synthetic routes for the preparation of scaffolds have been discussed to gain a better understanding of the issues that arise regarding toxicity. The focus here is also on concerns regarding the biocompatibility of the implants, given that the precursors and byproducts are poisonous.

Original Fluorinated Non-Isocyanate Polyhydroxyurethanes

New fluorinated polyhydroxyurethanes (FPHUs) with various molar weights were synthesized via the polyaddition reaction of a fluorinated telechelic bis(cyclocarbonate) (bis-CC) with a diamine. The fluorinated bis-CC was initially synthesized by carbonylation of a fluorinated diepoxide, 1,4-bis(2',3'-epoxypropyl)perfluorobutane, in the presence of LiBr catalyst, in high yield. Then, several reaction conditions were optimized through the model reactions of the fluorinated bis-CC with hexylamine. Subsequently, fluorinated polymers bearing hydroxyurethane moieties (FPHUs) were prepared by reacting the bis-CC with different hexamethylenediamine amounts in bulk at 80 °C and the presence of a catalyst. The chemoselective polymerization reaction yielded three isomers bearing primary and secondary hydroxyl groups in 61-82% yield. The synthesized fluorinated CCs and the corresponding FPHUs were characterized by ¹H, ¹⁹F, and ¹³C NMR spectroscopy. They were compared to their hydrogenated homologues synthesized in similar conditions. The gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) data of the FPHUs revealed a higher molar mass and a slight increase in glass transition and decomposition temperatures compared to those of the PHUs.

Influence of Phosphorus Structures and Their Oxidation States on Flame-Retardant Properties of Polyhydroxyurethanes

This article focuses on the synthesis of polyhydroxyurethane (PHU) materials containing novel phosphorus flame retardants (FR). Four different phosphorus compounds were grafted onto cyclic carbonate: 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO), diethyl phosphite (DEP), diphenyl phosphite (DPP) and dibenzo[d,f][1,3,2]dioxaphosphepine 6-oxide (BPPO). Thus, three novel phosphorus reactive cyclic carbonates which have never been reported so far were synthetized. Phosphorus FR containing PHU materials were characterized by FTIR to evidence the total conversion of the cyclic carbonate. Moreover, the gel contents up to 80% confirmed the formation of the polymer network. Then, the thermal stability and the flame-retardant properties were investigated by thermogravimetric analyses, cone calorimeter and pyrolysis combustion flow calorimeter. The mode of action of phosphorus compounds, depending on the oxidation state, was especially highlighted. Phosphonate (+III) provided better action in a condensed phase than phosphinate thanks to a more efficient char formation. Among phosphonates, differences were observed in terms of char-formation rate and expansion. DEP provided the best flame-retardant properties, with a reduction of 76% of pHRR with 2 wt% of phosphorus in cone calorimeter analysis. Therefore, this article highlighted the different modes of action of phosphorus flame retardants, depending on the oxidation state of phosphorus, in PHU materials.

Sustainable cycloaliphatic polyurethanes: from synthesis to applications

Polyurethanes (PUs) are a versatile and major polymer family, mainly produced via polyaddition between polyols and polyisocyanates. A large variety of fossil-based building blocks is commonly used to develop a wide range of macromolecular architectures with specific properties. Due to environmental concerns, legislation, rarefaction of some petrol fractions and price fluctuation, sustainable feedstocks are attracting significant attention, e.g., plastic waste and biobased resources from biomass. Consequently, various sustainable building blocks are available to develop new renewable macromolecular architectures such as aromatics, linear aliphatics and cycloaliphatics. Meanwhile, the relationship between the chemical structures of these building blocks and properties of the final PUs can be determined. For instance, aromatic building blocks are remarkable to endow materials with rigidity, hydrophobicity, fire resistance, chemical and thermal stability, whereas acyclic aliphatics endow them with oxidation and UV light resistance, flexibility and transparency. Cycloaliphatics are very interesting as they combine most of the advantages of linear aliphatic and aromatic compounds. This original and unique review presents a comprehensive overview of the synthesis of sustainable cycloaliphatic PUs using various renewable products such as biobased terpenes, carbohydrates, fatty acids and cholesterol and/or plastic waste. Herein, we summarize the chemical modification of the main sustainable cycloaliphatic feedstocks, synthesis of PUs using these building blocks and their corresponding properties and subsequently present their major applications in hot-topic fields, including building, transportation, packaging and biomedicine.

Functionalized β-Cyclodextrins Catalyzed Environment-Friendly Cycloaddition of Carbon Dioxide and Epoxides

Ammonium, imidazole, or pyridinium functionalized β-cyclodextrins (β-CDs) were used as efficient one-component bifunctional catalysts for the coupling reaction of carbon dioxide (CO₂) and epoxide without the addition of solvent and metal. The influence of different catalysts and reaction parameters on the catalytic performance were examined in detail. Under optimal conditions, Im-CD1-I catalysts functionalized with imidazole groups were able to convert various epoxides into target products with high selectivity and good conversion rates. The one-component bifunctional catalysts can also be recovered easily by filtration and reused at least for five times with only slight decrease in catalytic performance. Finally, a possible process for hydroxyl group-assisted ring-opening of epoxide and functionalized group- induced activation of CO₂ was presented.

Water-Induced Self-Blown Non-Isocyanate Polyurethane Foams

For 80 years, polyisocyanates and polyols were central building blocks for the industrial fabrication of polyurethane (PU) foams. By their partial hydrolysis, isocyanates release CO₂ that expands the PU network. Substituting this toxic isocyanate-based chemistry by a more sustainable variant-that in situ forms CO₂ by hydrolysis of a comonomer-is urgently needed for producing greener cellular materials. Herein, we report a facile, up-scalable process, potentially compatible to existing infrastructures, to rapidly prepare water-induced self-blown non-isocyanate polyurethane (NIPU) foams. We show that formulations composed of poly(cyclic carbonate)s and polyamines furnish rigid or flexible NIPU foams by partial hydrolysis of cyclic carbonates in the presence of a catalyst. By utilizing readily available low cost starting materials, this simple but robust process gives access to greener PU foams, expectedly responding to the sustainability demands of many sectors.

Biodegradable isocyanate-free polyurethane films via a noncatalytic route: facile modified polycaprolactone triol and biobased diamine as precursors

A facile synthesis of isocyanate free polyurethanes (PU) was executed by the reaction of biodegradable cyclic carbonate and sustainable diamines generated via chemical modification. The biodegradable polyol polycaprolactone triol (PCL) was transformed into a new glycerol carbonate derivative, PCL-(COOGC)₃, and subjected to polyaddition with the diamines linalool diamine (LLDA), isosorbide diamine (ISODA) and hexamethylene diamine (HDA). Polyaddition of PCL-(COOGC)₃ with the above diamine precursors was conducted via a one-pot reaction under catalyst-free reaction conditions prior to film casting. The above precursors were characterized by Fourier-transform infrared (FTIR) and ¹H and ¹³C nuclear magnetic resonance spectroscopies, high-resolution mass spectrometry and electrospray ionization matrix-assisted laser desorption/ionization time-of-flight mass spectrometry, whereas the PU films were studied by attenuated total reflectance-FTIR spectroscopy, solid state ¹³C NMR, scanning electron microscopy, energy-dispersive X-ray spectroscopy, Raman spectroscopy, X-ray diffractometry, differential scanning calorimetry and thermogravimetric analysis. High onset degradation temperature (T _d) values were observed for the PU films PU-1 (345.8 °C), PU-2 (309.6 °C) and PU-3 (344.6 °C), and further studies, including cross-link density, water contact angle, swelling behaviour and biodegradation (phosphate-buffered saline medium, pH = 7.2 at 45 °C) measurements, were conducted.

Preparation of Biobased Nonisocyanate Polyurethane/Epoxy Thermoset Materials Using Depolymerized Native Lignin

Polyurethane polymers are found in a wide range of material applications. However, the toxic nature of isocyanates used in their formulation is a major concern; hence, more environmentally friendly alternatives are of high interest in the search for new sustainable polymer materials. In this work, we present the preparation of isocyanate-free polyurethane/epoxy hybrid thermosets with a high biobased content (85-90 wt %). The isocyanate-free polyurethanes were based on polyhydroxyurethanes (PHUs) prepared from depolymerized native lignin, which we refer to as lignin hydrogenolysis oil (LHO). The LHO was functionalized with epichlorohydrin to yield the epoxidized structure (LHO-GE), which was in turn reacted with CO₂ to form the cyclocarbonated species (LHO-CC). Blends of the LHO-CC and glycerol diglycidyl ether (GDGE) were cured to produce hybrid PHU/epoxy (LHO-CC/GDGE) thermosets. Thermosetting materials with flexural moduli of 4.5 GPa and flexural strengths of 160 MPa were produced by optimizing the mass ratio of the two main components and the triamine hardener. These novel biobased hybrid materials outperformed the corresponding epoxy-only thermosets and comparable hybrid PHU/epoxy materials produced from petrochemicals.

Bio-Based Solid Electrolytes Bearing Cyclic Carbonates for Solid-State Lithium Metal Batteries

Green resources for lithium-based batteries excite many researchers due to their eco-friendly nature. In this work, a sustainable bio-based solid-state electrolyte was developed based on carbonated soybean oil (CSBO), obtained by organocatalyzed coupling of CO₂ to epoxidized soybean oil. CSBO coupled with lithium bis(trifluoromethanesulfonyl)imide salt on a bio-based cellulose separator resulted in free-standing membranes. Those membranes on electrochemical measurements exhibited ionic conductivity of around 10^-3  S cm^-1 at 100 °C and around 10^-6  S cm^-1 at room temperature with wide electrochemical stability window (up to 4.6 V vs. Li/Li⁺ ) and transference number up to 0.39 at RT. Further investigations on the galvanostatic charge-discharge of LiFePO₄ cathodes with CSBO-based electrolyte membranes and lithium metal anodes delivered the gravimetric capacity of 112 and 157 mAh g^-1 at RT and 60 °C, respectively, providing a promising direction to further develop bio-based solid electrolytes for sustainable solid-state lithium batteries.

Renewable Beta-Elemene Based Cyclic Carbonates for the Preparation of Oligo(hydroxyurethane)s

Conversion of β-elemene into new β-elemene dicarbonates through epoxidation and halide salt-catalyzed CO₂ cycloaddition reactions is reported. Step-growth polyaddition of this dicarbonate to five different, commercial diamines was investigated under neat conditions at 150 °C yielding non-isocyanate-based low molecular weight oligo(hydroxyurethane)s with 1.3≤M_n ≤6.3 kDa and 1.3≤Ð≤2.1, and with glass transition temperatures ranging from -59 to 84 °C. The preparation of one selected polyhydroxyurethane material, obtained in the presence of Jeffamine® D-2010 was scaled-up to 43 g. The latter, when combined in a formulation using Irgacure® 2100 and Laromer® LR 9000 allowed the preparation of coatings that were analyzed with several techniques showing the potential of these biobased oligourethanes towards the preparation of commercially relevant materials.

Lignin as a Renewable Building Block for Sustainable Polyurethanes

Currently, the pulp and paper industry generates around 50-70 million tons of lignin annually, which is mainly burned for energy recovery. Lignin, being a natural aromatic polymer rich in functional hydroxyl groups, has been drawing the interest of academia and industry for its valorization, especially for the development of polymeric materials. Among the different types of polymers that can be derived from lignin, polyurethanes (PUs) are amid the most important ones, especially due to their wide range of applications. This review encompasses available technologies to isolate lignin from pulping processes, the main approaches to convert solid lignin into a liquid polyol to produce bio-based polyurethanes, the challenges involving its characterization, and the current technology assessment. Despite the fact that PUs derived from bio-based polyols, such as lignin, are important in contributing to the circular economy, the use of isocyanate is a major environmental hot spot. Therefore, the main strategies that have been used to replace isocyanates to produce non-isocyanate polyurethanes (NIPUs) derived from lignin are also discussed.

Insights into the Design of Polyurethane Dressings Suitable for the Stages of Skin Wound-Healing: A Systematic Review

Dressings made with polyurethanes have been found to exhibit good and varied biological properties that make them good candidates for this application. However, as has been seen, the wound-healing process is complex, which includes four different stages. So far, the design and evaluation of polyurethane for wound dressing has focused on achieving good properties (mechanical, physicochemical, and biological), but each of them separates from the others or even directed at only one of the stages of skin wound-healing. Therefore, the aim of this systematic review is to explore the applications of polyurethanes in wound dressings and to determine whether could be designed to cover more than one stage of skin wound-healing. The PRISMA guidelines were followed. The current research in this field does not consider each stage separately, and the design of polyurethane dressings is focused on covering all the stages of wound healing with a single material but is necessary to replace polyurethanes in short periods of time. Additionally, little emphasis is placed on the hemostasis stage and further characterization of polyurethanes is still needed to correlate mechanical and physicochemical properties with biological properties at each stage of the wound-healing. Current research demonstrates an effort to characterize the materials physiochemically and mechanically, but in terms of their biological properties, most of the literature is based on the performance of histological tests of explants morphologically probing the compromised tissues, which give an indication of the potential use of polyurethanes in the generation of wound-healing dressings.

Choline Chloride/Urea Deep Eutectic Solvents: A Promising Reaction Medium for the Synthesis of Bio-Based Poly(hydroxyurethane)s

The development of more sustainable and eco-friendly polymers has attracted much attention from researchers over the past decades. Among the different strategies that can be implemented towards this goal, the substitution of the toxic reagents/monomers often used in polyurethane chemistry has stimulated much innovation leading to the development of the hydroxylated version of PURs, namely, the poly(hydroxyurethane)s (PHURs). However, some PHURs remain far from being sustainable as their synthesis may involve monomers and/or solvents displaying poor environmental impacts. Herein, we report on the use of more sustainable conditions to synthesize the biobased polycarbonates involved in the aminolysis reaction. In addition, we demonstrate that the use of renewable deep eutectic solvents (DESs) can act both as excellent solvents and organocatalysts to promote the aminolysis reaction.

Perspectives for the Upgrading of Bio-Based Vicinal Diols within the Developing European Bioeconomy

The previous decade has witnessed a drastic increase of European incentives aimed at pushing forward the transition from an exclusively petro-based economy toward a strong and homogeneous bio-based economy. Since 2012, numerous programs have been developed to stimulate and promote research and innovation relying on sustainable and renewable resources. Terrestrial biomass is a virtually infinite reservoir of biomacromolecules, the biorefining of which provides platform molecules of low complexity yet with tremendous industrial potential. Among such bio-based platform molecules, polyols and, more specifically, molecules featuring vicinal diols have gained tremendous interest and have stimulated an increasing research effort from the chemistry and chemical engineering communities. This Review revolves around the most promising process conditions and technologies reported since 2012 that specifically target bio-based vicinal diols and promote their transformation into value-added molecules of wide industrial interest, such as olefins, epoxides, cyclic carbonates, and ketals.

Cascade (Dithio)Carbonate Ring Opening Reactions for Self-Blowing Polyhydroxythiourethane Foams

Polyurethane (PU) foams are very common materials that have found many applications over the years. Their use is constantly improving due to their unique physical properties and easy blowing which does not require the addition of a blowing agent. Greener routes have been explored in the recent years to replace isocyanates. One of the most promising routes is leading to Polyhydroxyurethanes (PHU). However, with PHUs, external blowing agent are usually required to obtain a foam. Thus, our work focuses on PHU foam synthesis using in situ reaction to produce NIPU foam. Hence, the aminolysis of thiocyclic carbonate triggers Pearson reaction between released thiols and cyclic carbonates which serves as a chemical blowing agent. This article is protected by copyright. All rights reserved.

Enhanced and Reusable Poly(hydroxy urethane)-Based Low Temperature Hot-Melt Adhesives

Poly(hydroxy urethane)s (PHUs) based on 5-membered cyclic carbonates have emerged as sustainable alternatives to conventional isocyanate-based polyurethanes. However, while from the point of view of sustainability they represent an improvement, their properties are still not competitive with conventional polyurethanes. In this work, the potential of PHUs as reversible hot-melt adhesives is discussed. We found that with a judicious choice of reagents (i.e., the dicyclic carbonate and diamine), the detrimental hydrogen bonding between the soft segment of the chains and the pendant hydroxyl groups was partially avoided, thus imparting PHUs with hot-melt adhesion properties (i.e., adhesion at elevated temperatures and cohesiveness at a temperature lower than T_g/T_m). The importance of a balanced hard to soft segment ratio, along with the relevance of the chain extender in the final properties, is highlighted. Addition of aliphatic diamines (HMDA, 1,12-DAD) resulted in rubbery materials, while the employment of cycloaliphatic (CBMA) or aromatic ones (MXDA, PXDA) led to materials with hot-melt adhesive properties. The thermoreversibility of all compositions was assessed by rebonding specimens after lap-shear tests. Lap-shear strength values that were comparable to the virgin adhesives were observed. The breaking and reformation of hydrogen bonding interactions was demonstrated by FTIR measurements at different temperatures, as well as by rheological frequency sweep experiments. In order to mitigate the negative impact of the low molar mass PHUs and to enhance the service temperature of the adhesives, a hybrid PHU was prepared by adding a small amount of an epoxy resin, which acts as a cross-linker. These hybrid PHUs maintain the thermoreversibility displayed by thermoplastic PHUs while providing better adhesion at elevated temperatures. We believe that this work provides some important insights into the design of PHU-based hot-melt adhesives.

One-Pot Tandem Catalytic Epoxidation—CO2 Insertion of Monounsaturated Methyl Oleate to the Corresponding Cyclic Organic Carbonate

Conversion of unsaturated fatty acids, FAMEs or triglycerides into the corresponding cyclic organic carbonates involves two reaction steps—double-bond epoxidation and CO2 insertion into the epoxide—that are generally conducted separately. We describe an assisted-tandem catalytic protocol able to carry out carbonation of unsaturated methyl oleate in one-pot without isolating the epoxide intermediate. Methyl oleate carbonate was obtained in 99% yield and high retention of cis-configuration starting from methyl oleate using hydrogen peroxide and CO2 as green reagents, in a biphasic system and in the presence of an ammonium tungstate ionic liquid catalyst with KBr as co-catalyst.

Trends in non-isocyanate polyurethane (NIPU) development

The transition towards safer and more sustainable production of polymers has led to a growing body of academic research into non-isocyanate polyurethanes (NIPUs) as potential replacements for conventional, isocyanate-based polyurethane materials. This perspective article focuses on the opportunities and current limitations of NIPUs produced by the reaction between biobased cyclic carbonates with amines, which offers an interesting pathway to renewable NIPUs. While it was initially thought that due to the similarities in the chemical structure, NIPUs could be used to directly replace conventional polyurethanes (PU), this has proven to be more challenging to achieve in practice. As a result, and in spite of the vast amount of academic research into this topic, the market size of NIPUs remains negligible. In this perspective, we will emphasize the main limitations of NIPUs in comparison to conventional PUs and the most significant advances made by others and us to overcome these limitations. Finally, we provide our personal view of where research should be directed to promote the transition from the academic to the industrial sector.