Learning from nature: binary cooperative complementary nanomaterials

Application of 3D printing for fabrication of superhydrophobic surfaces with reversible wettability

Control of surface wettability is needed in many applications. The potential use of 3D printing technology to gain control over wettability remains largely unexplored. In this paper, Fused Deposition Molding (FDM) 3D printing technology was utilized to print polylactic acid (PLA) microplate array structures to generate superhydrophobic surfaces with reversable wetting properties. This was achieved by spraying polydimethylsiloxane (PDMS) and silica (SiO2) solutions, over microplate surfaces. Anisotropic wetting properties were also achieved based on the surface structure design. Due to the shape memory properties of PLA, the morphology of the microplate arrays could be switched between the original upright shape and deformed shape. Through alternating pressing and heating treatments, the microplate arrays showed anisotropic wettability switching. The difference between the contact angle (CA) and sliding angle (SA) of water droplets on the original surface parallel to and perpendicular to the microplate array direction were ΔCA = 7° and ΔSA = 3° respectively, and those on the surface of the deformed microplate array were ΔCA = 7° and ΔSA = 21°, respectively. This process enabled reversible alteration in the wetting behavior of water droplets on the original and deformed surfaces between sliding and sticking states. PLA-based shape memory anisotropic superhydrophobic surfaces with tunable adhesion were successfully applied to rewritable platforms, micro droplet reaction platforms, and gas sensing.

Antibacterial Hydrophilic ZnO Microstructure Film with Underwater Oleophobic and Self-Cleaning Antifouling Properties

Super-hydrophilic and oleophobic functional materials can prevent pollution or adsorption by repelling oil, and have good circulation. However, traditional strategies for preparing these functional materials either use expensive fabrication machines or contain possibly toxic organic polymers, which may prohibit the practical application. The research of multifunctional ZnO microstructures or nanoarrays thin films with super-hydrophilic, antifouling, and antibacterial properties has not been reported yet. Moreover, the exploration of underwater oleophobic and self-cleaning antifouling properties in ZnO micro/nanostructures is still in its infancy. Here, we prepared ZnO microstructured films on fluorine-doped tin oxide substrates (F-ZMF) for the development of advanced self-cleaning type super-hydrophilic and oleophobic materials. With the increase of the accelerators, the average size of the F-ZMF microstructures decreased. The F-ZMF shows excellent self-cleaning performance and hydrophilic (water contact angle ≤ 10°) and oleophobic characteristics in the underwater antifouling experiment. Under a dark condition, F-ZMF-4 showed good antibacterial effects against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) with inhibition rates of 99.1% and 99.9%, respectively. This study broadens the application scope of ZnO-based material and provides a novel prospect for the development of self-cleaning super-hydrophilic and oleophobic materials.

Silk Fibroin-Based Shape-Memory Organohydrogels with Semicrystalline Microinclusions

Inspired by nature, we designed organohydrogels (OHGs) consisting of a silk fibroin (SF) hydrogel as the continuous phase and the hydrophobic microinclusions based on semicrystalline poly(n-octadecyl acrylate) (PC18A) as the dispersed phase. SF acts as a self-emulsifier to obtain oil-in-water emulsions, and hence, it is a versatile and green alternative to chemical emulsifiers. We first prepared a stable oil-in-water emulsion without an external emulsifier by dispersing the n-octadecyl acrylate (C18A) monomer in an aqueous SF solution. To stabilize the emulsions for longer times, gelation in the continuous SF phase was induced by the addition of ethanol, which is known to trigger the conformational transition in SF from random coil to β-sheet structures. In the second step, in situ polymerization of C18A droplets in the emulsion system was conducted under UV light in the presence of a photoinitiator to obtain high-strength OHGs with shape-memory function, and good cytocompatibility. The incorporation of hydrophilic N,N-dimethylacrylamide and noncrystallizable hydrophobic lauryl methacrylate units in the hydrogel and organogel phases of OHGs, respectively, further improved their mechanical and shape-memory properties. The shape-memory OHGs presented here exhibit switchable viscoelasticity and mechanics, a high Young's modulus (up to 4.3 ± 0.1 MPa), compressive strength (up to 2.5 ± 0.1 MPa), and toughness (up to 0.68 MPa).

Bioinspired Under-Liquid Dual Superlyophobic Surface for On-Demand Oil/Water Separation

Porous membranes with under-liquid dual superlyophobic properties, which are difficult to achieve because of a thermodynamic contradiction, have attracted considerable interest in the field of switchable oil/water separation. Herein, a bioinspired mesh membrane with alternating hydrophilic and hydrophobic chemical patterns on its surface that endows it with superamphiphilic and under-liquid dual superlyophobic properties is fabricated by a simple liquidus modification process. The as-prepared membrane possesses a combination of under-oil superhydrophobic and under-water superoleophobic characteristics in the absence of external stimuli. Moreover, it can effectively perform the on-demand separation of various oil/water systems, including immiscible oil/water mixtures and oil/water emulsions owing to its under-liquid dual superlyophobic properties.

Flexible Superhydrophobic Microlens Arrays for Humid Outdoor Environment Applications

A microlens array (MLA) is an essential optical imaging device in the applications of augmented and virtual realities. The imaging of MLA would become blurry in a humid outdoor atmosphere. While the incorporation of superhydrophobicity to MLA would prevent the adhesion of droplets, the complex structure and the multiple fabrication process reduce the capability of optical imaging of MLA. Herein, a flexible superhydrophobic MLA with good optical imaging capability is successfully fabricated by the combination of 3D direct laser writing (DLW) and soft lithography. 3D DLW allows the fabrication of MLA with a hierarchical pillar array (h-MLA) in one step, which ensures good optical properties of the resulting polydimethylsiloxane (PDMS) h-MLA. The resulting h-MLAs with pitches ranging between 50 and 100 μm are superhydrophobic from which water droplets slide away at a sliding angle smaller than 15.6° and bounce off from the surface. Meanwhile, the hierarchical pillar array has a limited impact on the imaging capability and the field of view of h-MLA. With an optimized pitch of 60 μm, h-MLA has a transparency as good as MLA. Moreover, PDMS h-MLA retains excellent optical and superhydrophobic properties when bent and in an extremely humid environment. We believe that the proposed h-MLA could find applications in outdoor environments.

Controllable Fabrication of Durable, Underliquid Superlyophobic Surfaces Based on the Lyophilic-Lyophobic Balance

Surfaces possessing desirable underliquid special wettability, particularly underliquid dual superlyophobicity, have a high potential for extensive applications. However, there is still a lack of controllable preparation strategies to regulate the underliquid wettability via balancing the underliquid lyophilicity-lyophobicity. Herein, we develop a nanocomposite coating system comprising silica nanoparticles (NPs), glycerol propoxylate triglycidyl ether (GPTE), and fluorinated alkyl silane (FAS) to obtain controllable underliquid special wettability surfaces. FAS is the vital factor in guiding the preparation of the surface coating with expected underliquid superwettability. Increasing the FAS content results in a tendency toward underwater superoleophobicity/underoil hydrophilicity to underwater oleophilicity/underoil superhydrophobicity. Significantly, the underliquid dual superlyophobic surface can be achieved when an appropriate FAS content is located. After the coating treatment, the fabric exhibits superamphiphilicity in air and superlyophobicity in liquid (i.e., exhibiting both underwater superoleophobicity and underoil superhydrophobicity). The coating also exhibits an adaptable antioil fouling ability and high durability against harsh environments. Furthermore, oil/water separation based on the underliquid dual superlyophobicity of coated fabrics is successfully demonstrated. Our work proposes a new fabrication principle for the design of underliquid special wettability surfaces and offers broad applications, such as switchable oil/water separation, antibiofouling, liquid manipulation, and smart textiles.

Laser Fabrication of Titanium Alloy-Based Photothermal Responsive Slippery Surface

In recent years, biomimetic materials inspired from natural organisms have attracted great attention due to their promising functionalities and cutting-edge applications, emerging as an important research topic. For example, how to reduce the reflectivity of the solid surface and increase the absorption of the substrate surface is essential for developing light response smart surface. Suitable solutions to this issue can be found in natural creatures; however, it is technologically challenging. In this work, inspired from butterfly wings, we proposed a laser processing technology to prepare micro nanostructured titanium alloy surfaces with anti-reflection properties. The reflectivity is significantly suppressed, and thus, the light absorption is improved. Consequently, the anti-reflection titanium alloy surface can be further employed as a photothermal substrate for developing light-responsive slippery surface. The sliding behavior of liquid droplets on the smart slippery surface can be well controlled via light irradiation. This method facilitates the preparation of low-reflection and high-absorption metallic surfaces towards bionic applications.

Smart Bionic Surfaces with Switchable Wettability and Applications

In order to satisfy the needs of different applications and more complex intelligent devices, smart control of surface wettability will be necessary and desirable, which gradually become a hot spot and focus in the field of interface wetting. Herein, we review interfacial wetting states related to switchable wettability on superwettable materials, including several classical wetting models and liquid adhesive behaviors based on the surface of natural creatures with special wettability. This review mainly focuses on the recent developments of the smart surfaces with switchable wettability and the corresponding regulatory mechanisms under external stimuli, which is mainly governed by the transformation of surface chemical composition and geometrical structures. Among that, various external stimuli such as physical stimulation (temperature, light, electric, magnetic, mechanical stress), chemical stimulation (pH, ion, solvent) and dual or multi-triggered stimulation have been sought out to realize the regulation of surface wettability. Moreover, we also summarize the applications of smart surfaces in different fields, such as oil/water separation, programmable transportation, anti-biofouling, detection and delivery, smart soft robotic etc. Furthermore, current limitations and future perspective in the development of smart wetting surfaces are also given. This review aims to offer deep insights into the recent developments and responsive mechanisms in smart biomimetic surfaces with switchable wettability under external various stimuli, so as to provide a guidance for the design of smart surfaces and expand the scope of both fundamental research and practical applications.

Bioinspired organohydrogels with heterostructures: Fabrications, performances, and applications

Since emerging in 1960, the artificial hydrogels have garnered enormous attentions in scientific community due to their high level of similarities to biological soft tissues in both structures and properties. With the proceeding of research, the concern of hydrogels is gradually shifted from fundamental investigation to abundant functionalization. In contrast to the natural soft tissues, the current artificial hydrogels still possess relatively simple structures and unsatisfactory environmental adaptability, extremely limiting their practical applications in complex environments. Enlightened by the prominent adaptability of biological organisms, the binary cooperative complementary principle is utilized to develop bioinspired organohydrogels by combining two components with opposite but cooperative physiochemical features. The present review provides the advanced progresses of bioinspired organohydrogels with sophisticated heterogeneous networks and desirably environmental adaptabilities. We clearly summarize the synthesizing strategies in regard to both corresponding mechanisms and typical examples, including macroscopic organohydrogels, organohydrogels with binary solvent, organohydrogels with heteronetworks, and emulsion-based organohydrogels. Meanwhile, the intriguing features of the reported organohydrogels, such as temperature resistance, switchable mechanics, adaptive wettability, and opposite components compatibility, are also clearly highlighted with a short overview of their promising applications. Ultimately, the current challenges and perspectives on the future development of bioinspired organohydrogels are also discussed.

Interfacial Polymerization: From Chemistry to Functional Materials

Interfacial polymerization, where a chemical reaction is confined at the liquid-liquid or liquid-air interface, exhibits a strong advantage for the controllable fabrication of films, capsules, and fibers for use as separation membranes and electrode materials. Recent developments in technology and polymer chemistry have brought new vigor to interfacial polymerization. Here, we consider the history of interfacial polymerization in terms of the polymerization types: interfacial polycondensation, interfacial polyaddition, interfacial oxidative polymerization, interfacial polycoordination, interfacial supramolecular polymerization, and some others. The accordingly emerging functional materials are highlighted, as well as the challenges and opportunities brought by new technologies for interfacial polymerization. Interfacial polymerization will no doubt keep on developing and producing a series of fascinating functional materials.

Heteronetwork organohydrogels with exceptional swelling-resistance and adaptive antifouling performance

Multi-network organohydrogels with optional dispersion media and adaptive wettability have been developed, revealing adaptive antifouling properties and oil swelling-resistant elastomers.

High thermoelectric performance of Ag doped SnTe polycrystalline bulks via the synergistic manipulation of electrical and thermal transport

Ag substitution could effectively modify the electronic structures and thermoelectric performance for SnTe compounds especially at high temperatures.

Dual Superlyophobic Aliphatic Polyketone Membranes for Highly Efficient Emulsified Oil-Water Separation: Performance and Mechanism

Efficient treatment of difficult emulsified oil-water wastes is a global challenge. Membranes exhibiting unusual dual superlyophobicity (combined underwater superoleophobicity and underoil superhydrophobicity) are intriguing to realize high-efficiency separation of both oil-in-water and water-in-oil emulsions. For the first time, a robust polymeric membrane demonstrating dual superlyophobicity to common apolar oils was facilely fabricated via a simple one-step phase separation process using an aliphatic polyketone (PK) polymer, thanks to a conjunction of intermediate hydrophilicity and re-entrant fibril-like texture upon the prepared PK membrane. Further chemical modification to improve surface hydrophilicity slightly can enable dual superlyophobicity to both apolar and polar oils. It is found that a nonwetting composite state of oil against water or water against oil was obtainable on the membrane surfaces only when the probe liquids possess an equilibrium contact angle (θ_ow or θ_wo) larger than the critical re-entrant angle of the textured surfaces (73°), which can explain the existences of dual superlyophobicity and also the nonwetting to fully wetting transitions. A simple design chart was developed to map out the operational windows of material hydrophilicity and re-entrant geometry, that is, a possible zone, to help in the rational design of similar interfacial systems from various materials. Switchable filtrations of oil-in-water and water-in-oil nanoemulsions were achieved readily with both high flux and high rejection. The simplicity and scalability of the membrane preparation process and the well-elucidated underlying mechanisms illuminate the great application potential of the PK-based superwetting membranes.

Spatially Confined Assembly of Monodisperse Ruthenium Nanoclusters in a Hierarchically Ordered Carbon Electrode for Efficient Hydrogen Evolution

The redox units of polyaniline (PAni) are used cooperatively, and in situ, to assemble ruthenium (Ru) nanoclusters in a hierarchically ordered carbon electrode. The oxidized quinonoid imine (QI) units in PAni bond Ru complex ions selectively, whereas reduced benzenoid amine (BA) units cannot. By electrochemically tuning the ratio of QI to BA, Ru complexes are spatially confined in the outer layer of hierarchical PAni frameworks. Carbonization of Ru-PAni hybrids induces nucleation on the outer surface of the carbon support, generating nearly monodisperse Ru nanoclusters. The optimized catalyst has a low loading of approximately 2 wt % Ru, but exhibits a mass activity for the hydrogen evolution reaction that is about 6.8 times better than commercial 20 wt % Pt/C catalyst.

Controlled Attachment of Pseudomonas aeruginosa with Binary Colloidal Crystal-Based Topographies

Micro- and nanotopographies can interfere with bacteria attachment, however, the interplay existing between surface chemistry and topography remains unclear. Here, self-assembled spherical micrometer- silica and nanometer poly(methyl methacrylate) (PMMA)-sized particles are used to make binary colloidal crystal (BCC) topographical patterns to study bacterial attachment. A uniform surface chemistry of allylamine plasma polymer (AAMpp) is coated on the top of the BCCs to study only the topography effects. The uncoated and coated BCCs are exposed to Pseudomonas aeruginosa, and the surfaces and bacteria are characterized using scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and fluorescence microscopy. It is found that bacteria attachment to the uncoated BCCs is delayed and individual cells are attracted to the small particle regions of the patterns. Surprisingly, this phenomenon is also observed for the AAMpp-coated BCCs, with bacteria attaching to the small particle regions of the pattern, in stark contrast to uniform flat films of AAMpp that are highly adhesive toward P. aeruginosa. Also, the overall levels of bacterial attachment are significantly reduced by the BCC patterns compared to controls. Thus, there is a trade-off that exists between chemistry and topography that can be exploited to delay the onset of P. aeruginosa biofilm formation on surfaces.

A new view for nanoparticle assemblies: from crystalline to binary cooperative complementarity

Studies on nanoparticle assemblies and their applications have been research frontiers in nanoscience in the past few decades and remarkable progress has been made in the synthetic strategies and techniques. Recently, the design and fabrication of the nanoparticle-based nanomaterials or nanodevices with integrated and enhanced properties compared to those of the individual components have gradually become the mainstream. However, a systematic solution to provide a big picture for future development and guide the investigation of different aspects of the study of nanoparticle assemblies remains a challenge. The binary cooperative complementary principle could be an answer. The binary cooperative complementary principle is a universal discipline and can describe the fundamental properties of matter from the subatomic particles to the universe. According to its definition, a variety of nanoparticle assemblies, which represent the cutting-edge work in the nanoparticle studies, are naturally binary cooperative complementary materials. Therefore, the introduction of the binary cooperative complementary principle in the studies of nanoparticle assemblies could provide a unique perspective for reviewing this field and help in the design and fabrication of novel functional nanoparticle assemblies.

Underwater Mechanically Robust Oil-Repellent Materials: Combining Conflicting Properties Using a Heterostructure

The development of underwater mechanically robust oil-repellent materials is important due to the high demand for these materials with the increase in underwater activities. Based on the previous study, a new strategy is demonstrated to prepare underwater mechanically robust oil-repellent materials by combining conflicting properties using a heterostructure, which has a layered hydrophobic interior structure with a columnar hierarchical micro/nanostructure on the surface and a hydrophilic outer structure. The surface hydrophilic layer imparts underwater superoleophobicity and low oil adhesion to the material, which has oil contact angle of larger than 150° and adhesion of lower than 2.8 µN. The stability of the mechanical properties stemming from the interior hydrophobic-layered structure enables the material to withstand high weight loads underwater. The tensile stress and the hardness of such a heterostructure film after 1 month immersion in seawater and pH solution are in the range from 83.92 ± 8.22 to 86.73 ± 7.8 MPa and from 83.88 ± 6.8 to 86.82 ± 5.64 MPa, respectively, which are superior to any underwater oil-repellent material currently reported.

A "cation-anion regulation" synergistic anode host for dendrite-free lithium metal batteries

Dendritic Li deposition has been "a Gordian knot" for almost half a century, which significantly hinders the practical use of high-energy lithium metal batteries (LMBs). The underlying mechanisms of this dendrite formation are related to the preferential lithium deposition on the tips of the protuberances of the anode surface and also associated with the concentration gradient or even depletion of anions during cycling. Therefore, a synergistic regulation of cations and anions at the interface is vital to promoting dendrite-free Li anodes. An ingenious molecular structure is designed to realize the "cation-anion regulation" with strong interactions between adsorption sites and ions at the molecular level. A quaternized polyethylene terephthalate interlayer with a "lithiophilic" ester building block and an "anionphilic" quaternary ammonium functional block can guide ions to form dendrite-free Li metal deposits at an ultrahigh current density of 10 mA cm^-2, enabling stable LMBs.

SMART Design of a Bulk-Capped Supramolecular Segment for the Assembly into Organic Interdigital Lipid Bilayer-Like (ILB) Nanosheets

Rational molecular design for the organic nanocrystal morphology still remains a challenge due to the structural diversity and complicated weak intermolecular interactions. In this work, a typical attractor-repulsor molecule N,N-diphenyl-4-(9-phenyl-fluoren-9-yl) phenylamine (TPA-PF) is designed to explore a general assembly strategy for 2D nanocrystals. Via an interdigital lipid bilayer-like (ILB) molecular packing mode, large-sized lamellar 2D nanosheets are obtained with a length:width:thickness ratio as ≈2500:1000:1. The d-spacing of the largest (001) plane is 1.32 nm, which equals to the thickness of a single interdigital stacking layer. The synergetic effect of the attractive supramolecular segment (TPA) and the repulsive bulky group (PF) is supposed to be the critical factor for the ILB packing that leads to the 2D structures. The attractor-repulsor molecule design is expected to be an effective strategy for the growth of 2D nanocrystals based on small organic molecules.

Poly(methyl vinyl ether-alt-maleic acid) and ethyl monoester as building polymers for drug-loadable electrospun nanofibers

New biomaterials are sought for the development of bioengineered nanostructures. In the present study, electrospun nanofibers have been synthesized by using poly(methyl vinyl ether-alt-maleic acid) and poly(methyl vinyl ether-alt-maleic ethyl monoester) (PMVEMA-Ac and PMVEMA-ES, respectively) as building polymers for the first time. To further functionalize these materials, nanofibers of PMVEMA-Ac and PMVEMA-ES containing a conjugated polyelectrolyte (HTMA-PFP, blue emitter, and HTMA-PFNT, red emitter) were achieved with both forms maintaining a high solid state fluorescence yield without altered morphology. Also, 5-aminolevulinic acid (5-ALA) was incorporated within these nanofibers, where it remained chemically stable. In all cases, nanofiber diameters were less than 150 nm as determined by scanning and transmission electron microscopy, and encapsulation efficiency of 5-ALA was 97 ± 1% as measured by high-performance liquid chromatography. Both polymeric matrices showed rapid release kinetics in vertical cells (Franz cells) and followed Higuchi kinetics. In addition, no toxicity of nanofibers, in the absence of light, was found in HaCaT and SW480 cell lines. Finally, it was shown that loaded 5-ALA was functional, as it was internalized by cells in nanofiber-treated cultures and served as a substrate for the generation of protoporphyrin IX, suggesting these pharmaceutical vehicles are suitable for photodynamic therapy applications.

Large-Scale, Long-Range-Ordered Patterning of Nanocrystals via Capillary-Bridge Manipulation

Deterministic assembly of nanoparticles with programmable patterns is a core opportunity for property-by-design fabrication and large-scale integration of functional materials and devices. The wet-chemical-synthesized colloidal nanocrystals are compatible with solution assembly techniques, thus possessing advantages of high efficiency, low cost, and large scale. However, conventional solution process suffers from tradeoffs between spatial precision and long-range order of nanocrystal assembly arising from the uncontrollable dewetting dynamics and fluid flow. Here, a capillary-bridge manipulation method is demonstrated for directing the dewetting of nanocrystal inks and deterministically patterning long-range-ordered superlattice structures. This is achieved by employing micropillars with programmable size, arrangement, and shape, which permits deterministic manipulation of geometry, position, and dewetting dynamics of capillary bridges. Various superlattice structures, including one-dimensional (1D), circle, square, pentagon, hexagon, pentagram, cross arrays, are fabricated. Compared to the glassy thin films, long-range-ordered superlattice arrays exhibit improved ferroelectric polarization. Coassembly of nanocrystal superlattice and organic functional molecule is further demonstrated. Through introducing azobenzene into superlattice arrays, a switchable ferroelectric polarization is realized, which is triggered by order-disorder transition of nanocrystal stacking in reversible isomerization process of azobenzene. This method offers a platform for patterning nanocrystal superlattices and fabricating microdevices with functionalities for multiferroics, electronics, and photonics.

Superlyophilic Interfaces and Their Applications

Superlyophilic interfaces denote interfaces displaying strong affinity to diverse liquids, including superhydrophilic, superoleophilic, and superamphiphilic interfaces. When coming in contact with these interfaces, water or oil droplets tend to spread completely with contact angles close to 0°, presenting versatile applications including self-cleaning, antifogging, controllable liquid transport, liquid separation, and so forth. Inspired by nature, scientists have developed various kinds of artificial superlyophilic (SLPL) interfaces in the past decades. In terms of dimensional characteristics, the artificial SLPL interfaces can be divided into four categories: i) 0D particles, whose dispersibility or catalytic performance can be notably enhanced by superlyophilicity; ii) 1D micro-/nanofibers or nanotubes/channels, which can efficiently transfer liquids with SLPL interfaces; iii) 2D flat SLPL interfaces, on which different functional molecules can be deposited uniformly, forming ultrathin and smooth films; and iv) 3D structures, which can be obtained by either constructing 0D, 1D, or 2D SLPL materials separately or directly fabricating random SLPL frameworks, and can always be used as functional coatings or bulk materials. Here, natural and artificial SLPL interfaces are briefly introduced, followed by a short discussion of the limit between lyophilicity and lyophobicity, and then a snapshot of methods to generate SLPL interfaces is given. Specific focus is placed on recent achievements of constructing SLPL interfaces from zero to three dimensions. Following that, broad applications of SLPL interfaces in commercial areas will be introduced. Finally, a short summary and outlook for future challenges in this field is presented.

Nature-Inspired Na2Ti3O7 Nanosheets-Formed Three-Dimensional Microflowers Architecture as a High-Performance Anode Material for Rechargeable Sodium-Ion Batteries

Low cycling stability and poor rate performance are two of the distinctive drawbacks of most electrode materials for sodium-ion batteries (SIBs). Here, inspired by natural flower structures, we take advantage of the three-dimensional (3D) hierarchical flower-like stable microstructures formed by two-dimensional (2D) nanosheets to solve these problems. By precise control of the hydrothermal synthesis conditions, a novel three-dimensional (3D) flower-like architecture consisting of 2D Na₂Ti₃O₇ nanosheets (Na-TNSs) has been successfully synthesized. The arbitrarily arranged but closely interlinked thin nanosheets in carnation-shaped 3D Na₂Ti₃O₇ microflowers (Na-TMFs) originate a good network of electrically conductive paths in an electrode. Thus, Na-TMFs can get electrons from all directions and be fully utilized for sodium-ion insertion and extraction reactions, which can improve sodium storage properties with enhanced rate capability and super cycling performance. Furthermore, the large specific surface area provides a high capacity, which can be ascribed to the pseudo-capacitance effect. The wettability of the electrolyte was also improved by the porous and crumpled structure. The remarkably improved cycling performance and rate capability of Na-TMFs make a captivating case for its development as an advanced anode material for SIBs.

Nanoparticle-Programmed Surface for Drug Release and Cell Regulation via Reversible Hybridization Reaction

A surface directly connects the bulk of a material to its surroundings. The ability to dynamically regulate the surface without affecting the bulk of a material holds great potential for new applications. The purpose of this work was to demonstrate that the surface can be dynamically changed using nanoparticles and oligonucleotides (ODNs) in a reversible and reiterative manner. A dual-functional nanogel was synthesized as the model of nanoparticles using miniemulsion polymerization and click chemistry. The nanogel can not only adsorb drugs for sustained drug release but also bind a surface functionalized with complementary ODNs. Importantly, hybridization reaction and ODN degradation can drive reversible and reiterative nanogel binding to the surface for dynamic change, which in principle is unlimited. Moreover, nanogel-mediated dynamic change offers the surface with the drug-releasing function for inhibiting the growth of surrounding cells. Because nanogels can be replaced by any functional nanoparticles with a diverse array of properties, nanoparticle-programmed surface change constitutes a promising platform for various applications such as drug delivery and stent implantation.

Nanofluidics in two-dimensional layered materials: inspirations from nature

This review highlights the recent progress, current challenges, and future perspectives in the design and application of 2D layered materials for nanofluidic research, with emphasis on the thought of bio-inspiration.

Ordered Micro/Nanostructures with Geometric Gradient: From Integrated Wettability "Library" to Anisotropic Wetting Surface

Geometric gradients within ordered micro/nanostructures exhibit unique wetting properties. Well-defined and ordered microsphere arrays with geometric gradient (OMAGG) are successfully fabricated through combining colloidal lithography and inclined reactive ion etching (RIE). During the inclined RIE, the graded etching rates in vertical direction of etcher chamber are the key to generating a geometric gradient. The OMAGG can be used as an effective mask for the preparation of micro/nanostructure arrays with geometric gradient by selective RIE. Through this strategy, a well-defined wettability "library" with graded silicon cone arrays is fabricated, and the possibility of screening one desired "book" from the designated wettability "library" is demonstrated. Meanwhile, the silicon cone arrays with geometric gradient (SCAGG) can be applied to control the wetting behavior of water after being modified by hydrophilic or hydrophobic chemical groups. Based on this result, a temperature-responsive wetting substrate is fabricated by modifying poly n-isopropyl acrylamide (PNIPAM) on the SCAGG. These wettability gradients have great potential in tissue engineering, microfluidic devices, and integrated sensors.

Hierarchical Self-Assembly of Cu7Te5 Nanorods into Superstructures with Enhanced SERS Performance

This paper reports a strategy to get self-assembly of Cu₇Te₅ nanorods into hierarchical superstructures: the side-by-side self-assembly of nanorods into microscale one-dimensional (1D) nanowires (primary structure), the side-by-side alignments of the 1D nanowires into two-dimensional (2D) nanowire bundles (secondary structure), and the further rolling up of the 2D bundles into three-dimensional (3D) microtubes (tertiary structure). It was found that the oleylamine (OLA)/n-dodecanethiol (DDT) mixture as a binary capping agent was key to produce Cu₇Te₅ nanorods in the quantum size regime with high monodispersity, and this was a prerequisite for their hierarchical self-assembly based on elaborate control of the solvent evaporation process. The obtained Cu₇Te₅ microtube superstructures were used as SERS substrate and showed much stronger SERS enhancement than the as-prepared Cu₇Te₅ nanorods before assembly. This was probably ascribed to the remarkably enhanced local electromagnetic field arising from the plasmon coupling of Cu₇Te₅ nanorods in the well-assembled superstructures.

A Cooperative Interface for Highly Efficient Lithium-Sulfur Batteries

A cooperative interface constructed by "lithiophilic" nitrogen-doped graphene frameworks and "sulfiphilic" nickel-iron layered double hydroxides (LDH@NG) is proposed to synergistically afford bifunctional Li and S binding to polysulfides, suppression of polysulfide shuttles, and electrocatalytic activity toward formation of lithium sulfides for high-performance lithium-sulfur batteries. LDH@NG enables high rate capability, long lifespan, and efficient stabilization of both sulfur and lithium electrodes.

Amino-Fe3O4 Microspheres Directed Synthesis of a Series of Polyaniline Hierarchical Nanostructures with Different Wettability

We demonstrated polyaniline (PANI) dimensional transformation by adding trace amino-Fe3O4 microspheres to aniline polymerization. Different PANI nanostructures (i.e., flowers, tentacles, and nanofibers) could be produced by controlling the nucleation position and number on the surface of Fe3O4 microspheres, where hydrogen bonding were spontaneously formed between amino groups of Fe3O4 microspheres and aniline molecules. By additionally introducing an external magnetic field, PANI towers were obtained. These PANI nanostructures displayed distinctly different surface wettability in the range from hydrophobicity to hydrophilicity, which was ascribed to the synergistic effect of their dimension, hierarchy, and size. Therefore, the dimension and property of PANI nanostructures can be largely rationalized and predicted by adjusting the PANI nucleation and growth. Using PANI as a model system, the strategies presented here provide insight into the general scheme of dimension and structure control for other conducting polymers.

Controlling mesenchymal stem cells differentiate into contractile smooth muscle cells on a TiO2 micro/nano interface: Towards benign pericytes environment for endothelialization

Building healthy and oriented smooth muscle cells (SMCs) environment is an effective method for improving the surface endothelialization of the cardiovascular implants. However, a long-term and stable source of SMCs for implantation without immune rejection and inflammation has not been solved, and mesenchymal stem cells (MSCs) differentiation may be a good choice. In this work, two types of TiO2 micro/nano interfaces were fabricated on titanium surface by photolithography and anodic oxidation. These TiO2 micro/nano interfaces were used to regulate the differentiation of the MSCs. The X-ray diffraction (XRD) detection showed that the TiO2 micro/nano interfaces possessed the anatase crystal structure, suggesting good cytocompatibility. The CCK-8 results indicated the TiO2 micro/nano interfaces improved MSC proliferation, further immunofluorescence staining and calculation of the cell morphology index proved the micro/nano surfaces also elongated MSCs and regulated MSCs oriented growth. The specific staining of α-SMA, CNN-1, vWF, CD44 and CD133 markers revealed that the micro/nano surfaces induced MSCs differentiation to contractile SMCs, and the endothelial cells (ECs) culture experiment indicated that the MSCs induced by micro/nano interfaces contributed to the ECs attachment and proliferation. This method will be further studied and applied for the surface modification of the cardiovascular implants.

Facile Fabrication of Binary Nanoscale Interface for No-Loss Microdroplet Transportation

Binary nanoscale interfacial materials are fundamental issues in many applications for smart surfaces. A binary nanoscale interface with binary surface morphology and binary wetting behaviors has been prepared by a facile wet-chemical method. The prepared surface presents superhydrophobicity and high adhesion with the droplet at the same time. The composition, surface morphology, and wetting behaviors of the prepared surface have been systematic studied. The special wetting behaviors can be contributed to the binary nanoscale effect. The stability of the prepared surface was also investigated. As a primary application, a facile device based on the prepared binary nanoscale interface with superhydrophobicity and high adhesion was constructed for microdroplet transportation.

Nanoarchitectonics for Dynamic Functional Materials from Atomic-/Molecular-Level Manipulation to Macroscopic Action

Objects in all dimensions are subject to translational dynamism and dynamic mutual interactions, and the ability to exert control over these events is one of the keys to the synthesis of functional materials. For the development of materials with truly dynamic functionalities, a paradigm shift from "nanotechnology" to "nanoarchitectonics" is proposed, with the aim of design and preparation of functional materials through dynamic harmonization of atomic-/molecular-level manipulation and control, chemical nanofabrication, self-organization, and field-controlled organization. Here, various examples of dynamic functional materials are presented from the atom/molecular-level to macroscopic dimensions. These systems, including atomic switches, molecular machines, molecular shuttles, motional crystals, metal-organic frameworks, layered assemblies, gels, supramolecular assemblies of biomaterials, DNA origami, hollow silica capsules, and mesoporous materials, are described according to their various dynamic functions, which include short-term plasticity, long-term potentiation, molecular manipulation, switchable catalysis, self-healing properties, supramolecular chirality, morphological control, drug storage and release, light-harvesting, mechanochemical transduction, molecular tuning molecular recognition, hand-operated nanotechnology.

Ternary cooperative Au–CdS–rGO hetero-nanostructures: synthesis with multi-interface control and their photoelectrochemical sensor applications

This paper demonstrates the synthesis of ternary cooperative semiconductor–metal–graphene (Au–CdS–rGO) hetero-nanostructures. The obtained Au–CdS–rGO photoanode showed a greatly enhanced photoelectrochemical photocurrent.

Rational design of nanomaterials for water treatment

The ever-increasing human demand for safe and clean water is gradually pushing conventional water treatment technologies to their limits. It is now a popular perception that the solutions to the existing and future water challenges will hinge upon further developments in nanomaterial sciences. The concept of rational design emphasizes on 'design-for-purpose' and it necessitates a scientifically clear problem definition to initiate the nanomaterial design. The field of rational design of nanomaterials for water treatment has experienced a significant growth in the past decade and is poised to make its contribution in creating advanced next-generation water treatment technologies in the years to come. Within the water treatment context, this review offers a comprehensive and in-depth overview of the latest progress in rational design, synthesis and applications of nanomaterials in adsorption, chemical oxidation and reduction reactions, membrane-based separation, oil-water separation, and synergistic multifunctional all-in-one nanomaterials/nanodevices. Special attention is paid to the chemical concepts related to nanomaterial design throughout the review.

Hydrophobic/Hydrophilic Cooperative Janus System for Enhancement of Fog Collection

Harvesting micro-droplets from fog is a promising method for solving global freshwater crisis. Different types of fog collectors have been extensively reported during the last decade. The improvement of fog collection can be attributed to the immediate transportation of harvested water, the effective regeneration of the fog gathering surface, etc. Through learning from the nature's strategy for water preservation, the hydrophobic/hydrophilic cooperative Janus system that achieved reinforced fog collection ability is reported here. Directional delivery of the surface water, decreased re-evaporation rate of the harvested water, and thinner boundary layer of the collecting surface contribute to the enhancement of collection efficiency. Further designed cylinder Janus collector can facilely achieve a continuous process of efficient collection, directional transportation, and spontaneous preservation of fog water. This Janus fog harvesting system should improve the understanding of micro-droplet collection system and offer ideas to solve water resource crisis.