Monolithic and Flexible ZnS/SnO2 Ultraviolet Photodetectors with Lateral Graphene Electrodes

Upgrading Polyolefin Plastic Waste into Multifunctional Porous Graphene using Silicone-Assisted Direct Laser Writing

The widespread use of plastics, especially polyolefin including polyethylene and polypropylene, has led to severe environmental crises. Chemical recycling, a promising solution for extracting value from plastic waste, however, is underutilized due to its complexity. Here, a simple approach, silicone-assisted direct laser writing (SA-DLW) is developed, to upgrade polyolefin plastic waste into multifunctional porous graphene, called laser-induced graphene (LIG). This method involves infiltrating polyolefins with silicone, which retards ablation during the DLW process and supplies additional carbon atoms, as confirmed by experimental and molecular dynamic results. A remarkable conversion yield of 38.3% is achieved. The upgraded LIG exhibited a porous structure and high conductivity, which is utilized for the fabrication of diverse energy and electronic devices with commendable performance. Furthermore, the SA-DLW technique is versatile for upgrading plastic waste in various types and forms. Upgrading plastic waste in the form of fabric has significantly simplified pre-treatment. Finally, a wearable flex sensor is fabricated on the non-woven fabric of a discarded medical mask, which is applied for gesture monitoring. This work offers a simple but effective solution to upgrade plastic waste into valuable products, contributing to the mitigation of environmental challenges posed by plastic pollution.

Programmed multimaterial assembly by synergized 3D printing and freeform laser induction

In nature, structural and functional materials often form programmed three-dimensional (3D) assembly to perform daily functions, inspiring researchers to engineer multifunctional 3D structures. Despite much progress, a general method to fabricate and assemble a broad range of materials into functional 3D objects remains limited. Herein, to bridge the gap, we demonstrate a freeform multimaterial assembly process (FMAP) by integrating 3D printing (fused filament fabrication (FFF), direct ink writing (DIW)) with freeform laser induction (FLI). 3D printing performs the 3D structural material assembly, while FLI fabricates the functional materials in predesigned 3D space by synergistic, programmed control. This paper showcases the versatility of FMAP in spatially fabricating various types of functional materials (metals, semiconductors) within 3D structures for applications in crossbar circuits for LED display, a strain sensor for multifunctional springs and haptic manipulators, a UV sensor, a 3D electromagnet as a magnetic encoder, capacitive sensors for human machine interface, and an integrated microfluidic reactor with a built-in Joule heater for nanomaterial synthesis. This success underscores the potential of FMAP to redefine 3D printing and FLI for programmed multimaterial assembly.

Ten years of laser-induced graphene: impact and future prospect on biomedical, healthcare, and wearable technology

Since its introduction in 2014, laser-induced graphene (LIG) from commercial polymers has been gaining interests in both academic and industrial sectors. This can be clearly seen from its mass adoption in various fields ranging from energy storage and sensing platforms to biomedical applications. LIG is a 3-dimensional, nanoporous graphene structure with highly tuneable electrical, physical, and chemical properties. LIG can be easily produced by single-step laser scribing at normal room temperature and pressure using easily accessible commercial level laser machines and materials. With the increasing demand for novel wearable devices for biomedical applications, LIG on flexible substrates can readily serve as a technological platform to be further developed for biomedical applications such as point-of-care (POC) testing and wearable devices for healthcare monitoring system. This review will provide a comprehensive grounding on LIG from its inception and fabrication mechanism to the characterization of its key functional properties. The exploration of biomedicals applications in the form of wearable and point-of-care devices will then be presented. Issue of health risk from accidental exposure to LIG will be covered. Then LIG-based wearable devices will be compared to devices of different materials. Finally, we discuss the implementation of Internet of Medical Things (IoMT) to wearable devices and explore and speculate on its potentials and challenges.

Laser-Induced Graphene Formation on Polyimide Using UV to Mid-Infrared Laser Radiation

Our study presents laser-assisted methods to produce conductive graphene layers on the polymer surface. Specimens were treated using two different lasers at ambient and nitrogen atmospheres. A solid-state picosecond laser generating 355 nm, 532 nm, or 1064 nm wavelengths and a CO2 laser generating mid-infrared 10.6 µm wavelength radiation operating in a pulsed regime were used in experiments. Sheet resistance measurements and microscopic analysis of treated sample surfaces were made. The chemical structure of laser-treated surfaces was investigated using Raman spectroscopy, and it showed the formation of high-quality few-layer graphene structures on the PI surface. The intensity ratios I(2D)/I(G) and I(D)/I(G) of samples treated with 1064 nm wavelength in nitrogen atmosphere were 0.81 and 0.46, respectively. After laser treatment, a conductive laser-induced graphene layer with a sheet resistance as low as 5 Ω was formed. Further, copper layers with a thickness of 3-10 µm were deposited on laser-formed graphene using a galvanic plating. The techniques of forming a conductive graphene layer on a polymer surface have a great perspective in many fields, especially in advanced electronic applications to fabricate copper tracks on 3D materials.

Interface characteristics of graphene/ZnS hybrid-dimensional heterostructures

Graphene/ZnS hybrid-dimensional heterostructure is an excellent combination to regulate and improve the conductivity and sensitivity of components, in which the interface effects have crucial impacts on the performance of devices. In this work, we investigate the interface characteristics of Graphene/ZnS 2D/3D heterostructures. X-ray photoelectron spectra show that the ZnS binding energy shifts to lower energy by 0.3 eV after forming heterojunction with graphene. The fluorescence and absorption spectra confirm the luminescence enhancement and blue-shift of the absorbance edge of ZnS caused by graphene. The composition of Graphene/ZnS heterostructure facilitates separation and transfer of spatial charges, resulting in rapid electron transport.

Research Progress on the Preparation and Applications of Laser-Induced Graphene Technology

Graphene has been regarded as a potential application material in the field of new energy conversion and storage because of its unique two-dimensional structure and excellent physical and chemical properties. However, traditional graphene preparation methods are complicated in-process and difficult to form patterned structures. In recent years, laser-induced graphene (LIG) technology has received a large amount of attention from scholars and has a wide range of applications in supercapacitors, batteries, sensors, air filters, water treatment, etc. In this paper, we summarized a variety of preparation methods for graphene. The effects of laser processing parameters, laser type, precursor materials, and process atmosphere on the properties of the prepared LIG were reviewed. Then, two strategies for large-scale production of LIG were briefly described. We also discussed the wide applications of LIG in the fields of signal sensing, environmental protection, and energy storage. Finally, we briefly outlined the future trends of this research direction.

Review on Microscale Sensors with 3D Engineered Structures: Fabrication and Applications

The intelligence of modern technologies relies on perceptual systems based on microscale sensors. However, because of the traditional top-down fabrication approaches performed on planar silicon wafers, a large proportion of existing microscale sensors have 2D structures, which severely restricts their sensing capabilities. To overcome these restrictions, over the past few decades, increasing efforts have been devoted to developing new fabrication methods for microscale sensors with 3D engineered structures, from bulk chemical etching and 3D printing to molding and stress-induced assembly. Herein, the authors systematically review these fabrication methods based on the applications of the resulting 3D sensors and discuss their advantages compared to their 2D counterparts. This is followed by a perspective on the remaining challenges and possible opportunities.

Multi-Bandgap Monolithic Metal Nanowire Percolation Network Sensor Integration by Reversible Selective Laser-Induced Redox

Active electronics are usually composed of semiconductor and metal electrodes which are connected by multiple vacuum deposition steps and photolithography patterning. However, the presence of interface of dissimilar material between semiconductor and metal electrode makes various problems in electrical contacts and mechanical failure. The ideal electronics should not have defective interfaces of dissimilar materials. In this study, we developed a novel method to fabricate active electronic components in a monolithic seamless fashion where both metal and semiconductor can be prepared from the same monolith material without creating a semiconductor-metal interface by reversible selective laser-induced redox (rSLIR) method. Furthermore, rSLIR can control the oxidation state of transition metal (Cu) to yield semiconductors with two different bandgap states (Cu₂O and CuO with bandgaps of 2.1 and 1.2 eV, respectively), which may allow multifunctional sensors with multiple bandgaps from the same materials. This novel method enables the seamless integration of single-phase Cu, Cu₂O, and CuO, simultaneously while allowing reversible, selective conversion between oxidation states by simply shining laser light. Moreover, we fabricated a flexible monolithic metal-semiconductor-metal multispectral photodetector that can detect multiple wavelengths. The unique monolithic characteristics of rSLIR process can provide next-generation electronics fabrication method overcoming the limitation of conventional photolithography methods.

Physical and Chemical Sensors on the Basis of Laser-Induced Graphene: Mechanisms, Applications, and Perspectives

Laser-induced graphene (LIG) is produced rapidly by directly irradiating carbonaceous precursors, and it naturally exhibits as a three-dimensional porous structure. Due to advantages such as simple preparation, time-saving, environmental friendliness, low cost, and expanding categories of raw materials, LIG and its derivatives have achieved broad applications in sensors. This has been witnessed in various fields such as wearable devices, disease diagnosis, intelligent robots, and pollution detection. However, despite LIG sensors having demonstrated an excellent capability to monitor physical and chemical parameters, the systematic review of synthesis, sensing mechanisms, and applications of them combined with comparison against other preparation approaches of graphene is still lacking. Here, graphene-based sensors for physical, biological, and chemical detection are reviewed first, followed by the introduction of general preparation methods for the laser-induced method to yield graphene. The preparation and advantages of LIG, sensing mechanisms, and the properties of different types of emerging LIG-based sensors are comprehensively reviewed. Finally, possible solutions to the problems and challenges of preparing LIG and LIG-based sensors are proposed. This review may serve as a detailed reference to guide the development of LIG-based sensors that possess properties for future smart sensors in health care, environmental protection, and industrial production.

Practical Demonstration of Deep-Ultraviolet Detection with Wearable and Self-Powered Halide Perovskite-Based Photodetector

Flexible and self-powered photodetectors (PDs) have become one of the most popular topics, attracting researchers in the field of optoelectronic applications. In this study, for the first time, we demonstrate partial discharge detection in a practical environment with a prepared flexible device. Poly(vinylidene fluoride) (PVDF) is utilized as a highly transparent material in the UVC region, to create a flexible substrate with the antihumidity property. A detector that uses a mixed-halide perovskite (FAPbI₃)_1-x(MAPbBr₃)_x as the photoactive material is constructed in a vertical structure on the as-prepared hydrophobic PVDF substrate. The fabricated device exhibits good performance with a fast response speed (t_rise = 82 ms, t_fall = 64 ms) and a high detectivity of 7.21 × 10¹⁰ Jones at zero bias under 254 nm UV illumination, along with superior mechanical flexibility at various bending angles. Additionally, the air-exposure stability and reproducibility of the as-prepared device exhibit almost the original performance after 6 weeks of storage. For practical applications, we demonstrate a facile and sensitive detection for UVC leakage from a germicidal lamp and simulated a partial discharge system using our PD without energy consumption. These results indicate that this new approach may be useful and convenient for the detection of the partial discharge as well as for several practical applications.

Laser-induced graphene for bioelectronics and soft actuators

Laser-assisted process can enable facile, mask-free, large-area, inexpensive, customizable, and miniaturized patterning of laser-induced porous graphene (LIG) on versatile carbonaceous substrates (e.g., polymers, wood, food, textiles) in a programmed manner at ambient conditions. Together with high tailorability of its porosity, morphology, composition, and electrical conductivity, LIG can find wide applications in emerging bioelectronics (e.g., biophysical and biochemical sensing) and soft robots (e.g., soft actuators). In this review paper, we first introduce the methods to make LIG on various carbonaceous substrates and then discuss its electrical, mechanical, and antibacterial properties and biocompatibility that are critical for applications in bioelectronics and soft robots. Next, we overview the recent studies of LIG-based biophysical (e.g., strain, pressure, temperature, hydration, humidity, electrophysiological) sensors and biochemical (e.g., gases, electrolytes, metabolites, pathogens, nucleic acids, immunology) sensors. The applications of LIG in flexible energy generators and photodetectors are also introduced. In addition, LIG-enabled soft actuators that can respond to chemicals, electricity, and light stimulus are overviewed. Finally, we briefly discuss the future challenges and opportunities of LIG fabrications and applications.

Laser-Induced Graphene Electrochemical Immunosensors for Rapid and Label-Free Monitoring of Salmonella enterica in Chicken Broth

Food-borne illnesses are a growing concern for the food industry and consumers, with millions of cases reported every year. Consequently, there is a critical need to develop rapid, sensitive, and inexpensive techniques for pathogen detection in order to mitigate this problem. However, current pathogen detection strategies mainly include time-consuming laboratory methods and highly trained personnel. Electrochemical in-field biosensors offer a rapid, low-cost alternative to laboratory techniques, but the electrodes used in these biosensors require expensive nanomaterials to increase their sensitivity, such as noble metals (e.g., platinum, gold) or carbon nanomaterials (e.g., carbon nanotubes, or graphene). Herein, we report the fabrication of a highly sensitive and label-free laser-induced graphene (LIG) electrode that is subsequently functionalized with antibodies to electrochemically quantify the food-borne pathogen Salmonella enterica serovar Typhimurium. The LIG electrodes were produced by laser induction on the polyimide film in ambient conditions and, hence, circumvent the need for high-temperature, vacuum environment, and metal seed catalysts commonly associated with graphene-based electrodes fabricated via chemical vapor deposition processes. After functionalization with Salmonella antibodies, the LIG biosensors were able to detect live Salmonella in chicken broth across a wide linear range (25 to 10⁵ CFU mL^-1) and with a low detection limit (13 ± 7 CFU mL^-1; n = 3, mean ± standard deviation). These results were acquired with an average response time of 22 min without the need for sample preconcentration or redox labeling techniques. Moreover, these LIG immunosensors displayed high selectivity as demonstrated by nonsignificant response to other bacteria strains. These results demonstrate how LIG-based electrodes can be used for electrochemical immunosensing in general and, more specifically, could be used as a viable option for rapid and low-cost pathogen detection in food processing facilities before contaminated foods reach the consumer.

Stimulus Responsive 3D Assembly for Spatially Resolved Bifunctional Sensors

3D electronic/optoelectronic devices have shown great potentials for various applications due to their unique properties inherited not only from functional materials, but also from 3D architectures. Although a variety of fabrication methods including mechanically guided assembly have been reported, the resulting 3D devices show no stimuli-responsive functions or are not free standing, thereby limiting their applications. Herein, the stimulus responsive assembly of complex 3D structures driven by temperature-responsive hydrogels is demonstrated for applications in 3D multifunctional sensors. The assembly driving force, compressive buckling, arises from the volume shrinkage of the responsive hydrogel substrates when they are heated above the lower critical solution temperature. Driven by the compressive buckling force, the 2D-formed membrane materials, which are pre-defined and selectively bonded to the substrates, are then assembled to 3D structures. They include "tent," "tower," "two-floor pavilion," "dome," "basket," and "nested-cages" with delicate geometries. Moreover, the demonstrated 3D bifunctional sensors based on laser induced graphene show capability of spatially resolved tactile sensing and temperature sensing. These multifunctional 3D sensors would open new applications in soft robotics, bioelectronics, micro-electromechanical systems, and others.

Toward Imperfection-Insensitive Soft Network Materials for Applications in Stretchable Electronics

Development of stretchable devices with mechanical responses that mimic those of biological tissues/organs is of particular importance for the long-term biointegration, as the discomfort induced by the mechanical mismatch can be minimized. Recent works have established the bioinspired designs of soft network materials that can precisely reproduce the unconventional J-shaped stress-strain curves of human skin at different regions. Existing studies mostly focused on the design, fabrication, and modeling of perfect soft network materials. When utilized as the substrates of biointegrated electronics, the soft network designs, however, often need to incorporate deterministic holes, a type of imperfection, to accommodate hard, inorganic electronic components. Understanding of the effect of hole imperfections on the mechanical properties of soft network materials is thereby essential in practical applications. This paper presents a combined experimental and computational study of the stretchability and elastic modulus of imperfect soft network materials consisting of circular holes with a variety of diameters. Both the size and location of the circular-hole imperfections are shown to have profound influences on the stretchability. Based on these results, design guidelines of imperfection-insensitive network materials are introduced. For the imperfections that result in an evident reduction of stretchability, an effective reinforcement approach is presented by enlarging the width of horseshoe microstructures at strategic locations, which can enhance the stretchability considerably. A stretchable and imperfection-insensitive integrated device with a light-emitting diode embedded in the network material serves a demonstrative application.

Laser-Induced Graphene Triboelectric Nanogenerators

Triboelectric nanogenerators (TENGs) show exceptional promise for converting wasted mechanical energy into electrical energy. This study investigates the use of laser-induced graphene (LIG) composites as an exciting class of triboelectric materials in TENGs. Infrared laser irradiation is used to convert the surfaces of the two carbon sources, polyimide (PI) and cork, into LIG. This gives the bilayer composite films the high conductivity associated with LIG and the triboelectric properties of the carbon source. A LIG/PI composite is used to fabricate TENGs based on conductor-to-dielectric and metal-free dielectric-to-dielectric device geometries with open-circuit voltages >3.5 kV and peak power >8 mW. Additionally, a single sheet of PI is converted to a metal-free foldable TENG. The LIG is also embedded within a PDMS matrix to form a single-electrode LIG/PDMS composite TENG. This single-electrode TENG is highly flexible and stretchable and was used to generate power from mechanical contact with skin. The LIG composites present a class of triboelectric materials that can be made from naturally occurring and synthetic carbon sources.

Zinc oxide ultraviolet photodetectors: rapid progress from conventional to self-powered photodetectors

Currently, the development of ultraviolet (UV) photodetectors (PDs) has attracted the attention of the research community because of the vast range of applications of photodetectors in modern society. A variety of wide-band gap nanomaterials have been utilized for UV detection to achieve higher photosensitivity. Specifically, zinc oxide (ZnO) nanomaterials have attracted significant attention primarily due to their additional properties such as piezo-phototronic and pyro-phototronic effects, which allow the fabrication of high-performance and low power consumption-based UV PDs. This article primarily focuses on the recent development of ZnO nanostructure-based UV PDs ranging from nanomaterials to architectural device design. A brief overview of the photoresponse characteristics of UV PDs and potential ZnO nanostructures is presented. Moreover, the recent development in self-powered PDs and implementation of the piezo-phototronic effect, plasmonic effect and pyro-phototronic effect for performance enhancement is highlighted. Finally, the research perspectives and future research direction related to ZnO nanostructures for next-generation UV PDs are summarized.

Laser-Induced Graphene Composites as Multifunctional Surfaces

Laser-induced graphene (LIG) is a platform material for numerous applications. Despite its ease in synthesis, LIG's potential for use in some applications is limited by its robustness on substrates. Here, using a simple infiltration method, we develop LIG composites (LIGCs) with physical properties that are engineered on various substrate materials. The physical properties include surface properties such as superhydrophobicity and antibiofouling; the LIGCs are useful in antibacterial applications and Joule-heating applications and as resistive memory device substrates.

Rapid Synthesis of Zeolitic Imidazole Frameworks in Laser-Induced Graphene Microreactors

Various approaches to synthesize zeolitic imidazole frameworks (ZIFs) have been developed, such as solvothermal, sonochemical, microfluidic, and mechanochemical reactions. However, most of them are time consuming and involve complex processing steps, thus they cannot rapidly screen potential candidates to obtain ZIFs on demand. Such a challenge calls for efficient synthetic approaches. Herein, this challenge is overcome by employing two nonconventional heating strategies, that is, microwave and Joule heating, which are induced by laser-induced graphene (LIG) microreactors, to rapidly synthesize ZIFs. In the first reaction, the LIG acts as a susceptor that absorbs electromagnetic energy, which is converted into heat. In the latter one, LIG acts an electrical conductor that converts electrical energy to heat. Both of them can rapidly heat up the reactor, accelerating the crystal growth for synthesizing ZIFs with well-controlled morphology and crystallinity. To demonstrate a conceptual application, a ZIF-67/LIG composite was converted into Co/CoNC/LIG by a CO₂ laser-induced process. It showed excellent performance in the oxygen reduction reaction with a half-wave potential (E_1/2 ) of 0.798 V, and superior methanol tolerance and long-term stability. These rapid and facile synthesis methodologies will enable quick optimization of reaction conditions and fast screening of compound libraries for searching new materials, paving the way to high-throughput and autonomous nanomanufacturing.

High responsivity ultraviolet detector based on novel SnO2 nanoarrays

In this work, tin oxide (SnO₂) nanoarrays (NAs) with a novel morphology were fabricated by a hydrothermal method.

Physico-chemical investigation of ZnS thin-film deposited from ligand-free nanocrystals synthesized by non-hydrolytic thio-sol-gel

Ultra-small and monodispersed zinc sulfide nanocrystals (NCs) (d ≤ 3 nm) have been prepared without the use of any surfactants by a synthetic route using benzyl mercaptan as a source of sulfur. The prepared NCs are dispersible in highly polar solvents and display the capability to closely pack-up in a bulky film. The NCs were characterized by TEM, XRD and UV-vis optical absorption as well as by steady-state and time-resolved photoluminescence (PL) spectroscopies. Uniform films of ZnS were spin-coated on glass and ITO-glass substrates using a NCs dispersion in N,N-dimethylformamide. The NCs and the resulting films were characterized by morphological and optoelectronic probing techniques such as AFM, SEM, diffuse reflectance, PL and photoelectron spectroscopy in air. These physical investigations confirmed that the chalcogenide NCs grown by this method have the potential to be utilized directly as photocatalysts and are potentially useful building-blocks/starting materials for the fabrication of semiconductor thin films for optoelectronic applications such as LED, luminescent screens, field effect transistor and solar cells. Insights on the chemistry involved in the NCs growth have been provided revealing that their formation proceeds through a mechanism involving a thioether elimination reaction.

Laser-Induced Graphene

Research on graphene abounds, from fundamental science to device applications. In pursuit of complementary morphologies, formation of graphene foams is often preferred over the native two-dimensional (2D) forms due to the higher available area. Graphene foams have been successfully prepared by several routes including chemical vapor deposition (CVD) methods and by wet-chemical approaches. For these methods, one often needs either high temperature furnaces and highly pure gases or large amounts of strong acids and oxidants. In 2014, using a commercial laser scribing system as found in most machine shops, a direct lasing of polyimide (PI) plastic films in the air converted the PI into 3D porous graphene, a material termed laser-induced graphene (LIG). This is a one-step method without the need for high-temperature reaction conditions, solvent, or subsequent treatments, and it affords graphene with many five-and seven-membered rings. With such an atomic arrangement, one might call LIG "kinetic graphene" since there is no annealing in the process that causes the rearrangement to the preferred all-six-membered-ring form. In this Account, we will first introduce the approaches that have been developed for making LIG and to control the morphology as either porous sheets or fibrils, and to control porosity, composition, and surface properties. The surfaces can be varied from being either superhydrophilic with a 0° contact angle with water to being superhydrophobic having >150° contact angle with water. While it was initially thought that the LIG process could only be performed on PI, it was later shown that a host of other polymeric substrates, nonpolymers, metal/plastic composites, and biodegradable and naturally occurring materials and foods could be used as platforms for generating LIG. Methods of preparation include roll-to-roll production for fabrication of in-plane electronics and two different 3D printing (additive manufacturing) routes to specific shapes of LIG monoliths using both laminated object manufacturing and powder bed fabrication methods. Use of the LIG in devices is performed very simply. This is showcased with high performance supercapacitors, fuel cell materials for oxygen reduction reactions, water splitting for both hydrogen and oxygen evolution reactions coming from the same plastic sheet, sensor devices, oil/water purification platforms, and finally applications in both passive and active biofilm inhibitors. So the ease of formation of LIG, its simple scale-up, and its utility for a range of applications highlights the easy transition of this substrate-bound graphene foam into commercial device platforms.

Utilizing Interlayer Excitons in Bilayer WS2 for Increased Photovoltaic Response in Ultrathin Graphene Vertical Cross-Bar Photodetecting Tunneling Transistors

Here we study the layer-dependent photoconductivity in Gr/WS₂/Gr vertical stacked tunneling (VST) cross-bar devices made using two-dimensional (2D) materials all grown by chemical vapor deposition. The larger number of devices (>100) enables a statistically robust analysis on the comparative differences in the photovoltaic response of monolayer and bilayer WS₂, which cannot be achieved in small batch devices made using mechanically exfoliated materials. We show a dramatic increase in photovoltaic response for Gr/WS₂(2L)/Gr compared to monolayers because of the long inter- and intralayer exciton lifetimes and the small exciton binding energy (both interlayer and intralayer excitons) of bilayer WS₂ compared with that of monolayer WS₂. Different doping levels and dielectric environments of top and bottom graphene electrodes result in a potential difference across a ∼1 nm vertical device, which gives rise to large electric fields perpendicular to the WS₂ layers that cause band structure modification. Our results show how precise control over layer number in all 2D VST devices dictates the photophysics and performance for photosensing applications.

Laser-Induced Graphene by Multiple Lasing: Toward Electronics on Cloth, Paper, and Food

A simple and facile method for obtaining patterned graphene under ambient conditions on the surface of diverse materials ranging from renewable precursors such as food, cloth, paper, and cardboard to high-performance polymers like Kevlar or even on natural coal would be highly desirable. Here, we report a method of using multiple pulsed-laser scribing to convert a wide range of substrates into laser-induced graphene (LIG). With the increased versatility of the multiple lase process, highly conductive patterns can be achieved on the surface of a diverse number of substrates in ambient atmosphere. The use of a defocus method results in multiple lases in a single pass of the laser, further simplifying the procedure. This method can be implemented without increasing processing times when compared with laser induction of graphene on polyimide (Kapton) substrates as previously reported. In fact, any carbon precursor that can be converted into amorphous carbon can be converted into graphene using this multiple lase method. This may be a generally applicable technique for forming graphene on diverse substrates in applications such as flexible or even biodegradable and edible electronics.

Bioinspired multi-responsive soft actuators controlled by laser tailored graphene structures

Aligned laser induced graphene (LIG) functions as a stiff constraining element for multi-responsive soft actuators with programmable shape transformation.

Reversible Self-Assembly of 3D Architectures Actuated by Responsive Polymers

An assembly of three-dimensional (3D) architectures with defined configurations has important applications in broad areas. Among various approaches of constructing 3D structures, a stress-driven assembly provides the capabilities of creating 3D architectures in a broad range of functional materials with unique merits. However, 3D architectures built via previous methods are simple, irreversible, or not free-standing. Furthermore, the substrates employed for the assembly remain flat, thus not involved as parts of the final 3D architectures. Herein, we report a reversible self-assembly of various free-standing 3D architectures actuated by the self-folding of smart polymer substrates with programmed geometries. The strategically designed polymer substrates can respond to external stimuli, such as organic solvents, to initiate the 3D assembly process and subsequently become the parts of the final 3D architectures. The self-assembly process is highly controllable via origami and kirigami designs patterned by direct laser writing. Self-assembled geometries include 3D architectures such as "flower", "rainbow", "sunglasses", "box", "pyramid", "grating", and "armchair". The reported self-assembly also shows wide applicability to various materials including epoxy, polyimide, laser-induced graphene, and metal films. The device examples include 3D architectures integrated with a micro light-emitting diode and a flex sensor, indicting the potential applications in soft robotics, bioelectronics, microelectromechanical systems, and others.

Flexible Photodetectors Based on Novel Functional Materials

Flexible photodetectors have attracted a great deal of research interest in recent years due to their great possibilities for application in a variety of emerging areas such as flexible, stretchable, implantable, portable, wearable and printed electronics and optoelectronics. Novel functional materials, including materials with zero-dimensional (0D) and one-dimensional (1D) inorganic nanostructures, two-dimensional (2D) layered materials, organic semiconductors and perovskite materials, exhibit appealing electrical and optoelectrical properties, as well as outstanding mechanical flexibility, and have been widely studied as building blocks in cost-effective flexible photodetection. Here, we comprehensively review the outstanding performance of flexible photodetectors made from these novel functional materials reported in recent years. The photoresponse characteristics and flexibility of the devices will be discussed systematically. Summaries and challenges are provided to guide future directions of this vital research field.

Heterostructured ZnS/InP nanowires for rigid/flexible ultraviolet photodetectors with enhanced performance

Heterostructured ZnS/InP nanowires, composed of single-crystalline ZnS nanowires coated with a layer of InP shell, were synthesized via a one-step chemical vapor deposition process. As-grown heterostructured ZnS/InP nanowires exhibited an ultrahigh I_on/I_off ratio of 4.91 × 10³, a high photoconductive gain of 1.10 × 10³, a high detectivity of 1.65 × 10¹³ Jones and high response speed even in the case of very weak ultraviolet light illumination (1.87 μW cm^-2). The values are much higher than those of previously reported bare ZnS nanowires owing to the formation of core/shell heterostructures. Flexible ultraviolet photodetectors were also fabricated with the heterostructured ZnS/InP nanowires, which showed excellent mechanical flexibility, electrical stability and folding endurance besides excellent photoresponse properties. The results elucidated that the heterostructured ZnS/InP nanowires could find good applications in next generation flexible optoelectronic devices.

Bioinspired Programmable Polymer Gel Controlled by Swellable Guest Medium

Responsive materials with functions of forming three-dimensional (3D) origami and/or kirigami structures have a broad range of applications in bioelectronics, metamaterials, microrobotics, and microelectromechanical (MEMS) systems. To realize such functions, building blocks of actuating components usually possess localized inhomogeneity so that they respond differently to external stimuli. Previous fabrication strategies lie in localizing nonswellable or less-swellable guest components in their swellable host polymers to reduce swelling ability. Herein, inspired by ice plant seed capsules, we report an opposite strategy of implanting swellable guest medium inside nonswellable host polymers to locally enhance the swelling inhomogeneity. Specifically, we adopted a skinning effect induced surface polymerization combined with direct laser writing to control gradient of swellable cyclopentanone (CP) in both vertical and lateral directions of the nonswellable SU-8. For the first time, the laser direct writing was used as a novel strategy for patterning programmable polymer gel films. Upon stimulation of organic solvents, the dual-gradient gel films designed by origami or kirigami principles exhibit reversible 3D shape transformation. Molecular dynamics (MD) simulation illustrates that CP greatly enhances diffusion rates of stimulus solvent molecules in the SU-8 matrix, which offers the driving force for the programmable response. Furthermore, this bioinspired strategy offers unique capabilities in fabricating responsive devices such as a soft gripper and a locomotive robot, paving new routes to many other responsive polymers.