Nanoporous membranes for medical and biological applications: Nanoporous membranes for medical and biological applications

Improved Protein Removal Performance of PES Hollow-Fiber Ultrafiltration Membrane with Sponge-like Structure

The research used polyethersulfone (PES) as a membrane material, polyvinylpyrrolidone (PVP) k30 and polyethylene glycol 400 (PEG 400) as water-soluble additives, and dimethylacetamide (DMAc) as a solvent to prepare hollow-fiber ultrafiltration membranes through a nonsolvent-induced phase separation (NIPS) process. The hydrophilic nature of PVP-k30 and PEG caused them to accumulate on the membrane surface during phase separation. The morphology, chemical composition, surface charge, and pore size of the PES membranes were evaluated by SEM, FTIR, zeta potential, and dextran filtration experiments. The paper also investigated how different spinning solution compositions affected membrane morphology and performance. The separation efficiency of membranes with four different morphologies was tested in single-protein and double-protein mixed solutions. The protein separation effectiveness of the membrane was studied through molecular weight cutoff, zeta potential, and static protein adsorption tests. In addition, the operating pressure and pH value were adjusted to improve ultrafiltration process conditions. The PES membrane with an intact sponge-like structure showed the highest separation factor of 11, making it a prime candidate membrane for the separation of bovine serum albumin (BSA) and lysozyme (LYS). The membrane had a minimal static protein adsorption capacity of 48 mg/cm2 and had excellent anti-fouling properties. When pH = 4, the BSA retention rate was 93% and the LYS retention rate was 23%. Furthermore, it exhibited excellent stability over a pH range of 1-13, confirming its suitability for protein separation applications.

Silicone cryogel skeletons enhance the survival and mechanical integrity of hydrogel-encapsulated cell therapies

The transplantation of engineered cells that secrete therapeutic proteins presents a promising method for addressing a range of chronic diseases. However, hydrogels used to encase and protect non-autologous cells from immune rejection often suffer from poor mechanical properties, insufficient oxygenation, and fibrotic encapsulation. Here, we introduce a composite encapsulation system comprising an oxygen-permeable silicone cryogel skeleton, a hydrogel matrix, and a fibrosis-resistant polymer coating. Cryogel skeletons enhance the fracture toughness of conventional alginate hydrogels by 23-fold and oxygen diffusion by 2.8-fold, effectively mitigating both implant fracture and hypoxia of encapsulated cells. Composite implants containing xenogeneic cells engineered to secrete erythropoietin significantly outperform unsupported alginate implants in therapeutic delivery over 8 weeks in immunocompetent mice. By improving mechanical resiliency and sustaining denser cell populations, silicone cryogel skeletons enable more durable and miniaturized therapeutic implants.

Photo-responsive nanoporous liquid crystal polymer films for selective dye adsorption

Photo-responsive nanoporous polymer films (AZOF-R(NC6)) have been developed by a template method based on a hydrogen-bonding supramolecular liquid crystal (LC) and a light-sensitive azobenzene LC crosslinker in this work. Anionic nanopores were obtained after the removal of template NC6 using KOH solution. The AZOF-R(NC6) demonstrates charge-selective dye adsorption and the maximum adsorption capacity for Rh6G is 504.6 mg g-1. The AZOF-R(NC6) film without UV light treatment shows a 32% higher adsorption capacity for Rh6G than the AZOF-R(NC6) film treated with UV light within the initial 10 min. In addition, UV light can trigger the release of the adsorbed dye from the polymer film due to the pore size change arising from the trans-cis isomerization. Besides, the used polymer film can be effectively regenerated using a HCl solution. Such functional polymer films with highly ordered nanopores and photo-responsive properties hold great promise in selective adsorption and mass separations.

Simulation and Analysis of Anodized Aluminum Oxide Membrane Degradation

Microelectromechanical systems (MEMS)-based filter with microchannels enables the removal of various microorganisms, including viruses and bacteria, from fluids. Membranes with porous channels can be used as filtration interfaces in MEMS hemofilters or mini-dialyzers. The main problems associated with the filtration process are optimization of membrane geometry and fouling. A nanoporous aluminum oxide membrane was fabricated using an optimized two-step anodization process. Computational strength modeling and analysis of the membrane with specified parameters were performed using the ANSYS structural module. A fuzzy simulation was performed for the numerical analysis of flux through the membrane. The membrane was then incorporated with the prototype for successive filtration. The fluid flux and permeation analysis of the filtration process have been studied. Scanning electron microscope (SEM) micrographs of membranes have been obtained before and after the filtration cycles. The SEM results indicate membrane fouling after multiple cycles, and thus the flux is affected. This type of fabricated membrane and setup are suitable for the separation and purification of various fluids. However, after several filtration cycles, the membrane was degraded. It requires a prolonged chemical cleaning. High-density water has been used for filtration purposes, so this MEMS-based filter can also be used as a mini-dialyzer and hemofilter in various applications for filtration. Such a demonstration also opens up a new strategy for maximizing filtration efficiency and reducing energy costs for the filtration process by using a layered membrane setup.

A Commercial Clay-Based Material as a Carrier for Targeted Lysozyme Delivery in Animal Feed

The controlled supply of bioactive molecules is a subject of debate in animal nutrition. The release of bioactive molecules in the target organ, in this case the intestine, results in improved feed, as well as having a lower environmental impact. However, the degradation of bioactive molecules' in transit in the gastrointestinal passage is still an unresolved issue. This paper discusses the feasibility of a simple and cost-effective procedure to bypass the degradation problem. A solid/liquid adsorption procedure was applied, and the operating parameters (pH, reaction time, and LY initial concentration) were studied. Lysozyme is used in this work as a representative bioactive molecule, while Adsorbo®, a commercial mixture of clay minerals and zeolites which meets current feed regulations, is used as the carrier. A maximum LY loading of 32 mgLY/gAD (LY(32)-AD) was obtained, with fixing pH in the range 7.5-8, initial LY content at 37.5 mgLY/gAD, and reaction time at 30 min. A full characterisation of the hybrid organoclay highlighted that LY molecules were homogeneously spread on the carrier's surface, where the LY-carrier interaction was mainly due to charge interaction. Preliminary release tests performed on the LY(32)-AD synthesised sample showed a higher releasing capacity, raising the pH from 3 to 7. In addition, a preliminary Trolox equivalent antioxidant capacity (TEAC) assay showed an antioxidant capacity for the LY of 1.47 ± 0.18 µmol TroloxEq/g with an inhibition percentage of 33.20 ± 3.94%.

pH-Responsive Membranes from Self-Assembly of Poly(2-(dimethylamino)ethyl methacrylate) Brush Silica Nanoparticles

We have prepared novel pH-responsive nanoporous membranes by the self-assembly of silica nanoparticles carrying poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) brushes with a degree of polymerization (DP) in the 100-450 range. The nanoparticles were prepared by surface-initiated ARGET-ATRP, and the membranes were assembled by pressure-driven deposition onto porous supports. The permeability and pore size of the resulting robust membranes were studied using water and hexane flux and filtration cutoff experiments. The pore size of the PDMAEMA "hairy" silica nanoparticle (HNP) membranes measured by water flux was ca. 22 nm and was mostly independent of the polymer brush length. We attributed this to a combination of the PDMAEMA brushes swelling and their permeability to water. In contrast, the pore size measured by hexane flux strongly depended on the DP. The flux and pore size of these membranes in water strongly depended on the pH. The pore size decreased by a factor of 1.6 when the pH was changed from neutral to acidic. pH-Responsive HNP membranes combine many attractive properties, including control over the filtration cutoff, responsive permeability, and high flux at low pressure. The reversible self-assembly of the PDMAEMA HNP membranes may help not only in their facile preparation but also in material recycling if biofouling occurs. The key features of the PDMAEMA HNP assemblies are attractive in membrane separations, molecular valves, and biosensors, where having precise control over the pore size and pore gating is highly desirable.

Temperature-Responsive Nanoporous Membranes from Self-Assembly of Poly(N-isopropylacrylamide) Hairy Nanoparticles

Nanoporous membranes play a critical role in numerous separations on laboratory and industrial scales, ranging from water treatment to biotechnology. However, few strategies exist that allow for the preparation of mechanically robust nanoporous membranes whose separation properties can be easily tuned. Here, we introduce a new family of tunable nanoporous membranes based on nanoparticles decorated with temperature-responsive polymer brushes. We prepared mechanically robust membranes from hairy nanoparticles (HNPs) carrying PNIPAM polymer brushes. We assembled the HNPs into thin films through pressure-driven deposition of nanoparticle suspensions and measured the permeability and filtration cutoff of these membranes at different temperatures. The membrane pore diameter at room temperature varied between 10 and 30 nm depending on the polymer length. The water permeability of these membranes could be controlled by temperature, with the effective pore diameter increasing by a factor of 3-6 (up to 100 nm) when the temperature was increased to 60 °C. The size selectivity of these membranes in the filtration of nanoparticles could also be attenuated by temperature. Molecular dynamics computer simulations of a coarse-grained HNP model show that temperature-sensitive pores sizes are consistent with our experimental results and reveal the polymer configurations responsible for the observed filtration membrane permeability. We expect that these membranes will be useful for separations and in the preparation of responsive microfluidic devices.

Electrostatic Repulsive Features of Free-Standing Titanium Dioxide Nanotube-Based Membranes in Biofiltration Applications

This study presents the electrostatic repulsive features of electrochemically fabricated titanium dioxide nanotube (NT)-based membranes with different surface nanomorphologies in cross-flow biofiltration applications while maintaining a creatinine clearance above 90%. Although membranes exhibit antifouling behavior, their blood protein rejection can still be improved. Due to the electrostatically negative charge of the hexafluorotitanate moiety, the fabricated biocompatible, superhydrophilic, free-standing, and amorphous ceramic nanomembranes showed that about 20% of negatively charged 66 kDa blood albumin was rejected by the membrane with ∼100 nm pores. As the nanomorphology of the membrane was shifted from NTs to nanowires by varying fabrication parameters, pure water flux and bovine serum albumin (BSA) rejection performance were reduced, and the membrane did not lose its antifouling behavior. Herein, nanomembranes with different surface nanomorphologies were fabricated by a multi-step anodic oxidation process and characterized by scanning electron microscopy, atomic force microscopy, water contact angle analysis, X-ray diffraction, and energy-dispersive X-ray spectroscopy. The membrane performance of samples was measured in 3D printed polyethylene terephthalate glycol flow cells replicating implantable artificial kidney models to determine their blood toxin removal and protein loss features. In collected urine mimicking samples, creatinine clearances and BSA rejections were measured by the spectrophotometric Jaffe method and high-performance liquid chromatography.

Modeling transport and filtration of nanoparticle suspensions in porous media

Recently membrane filters have gained in significance due to the need to provide protection against airborne pollution. A question of importance, and some controversy, is the efficiency of filters for small nanoparticles with diameters below 100 nm as these are considered particularly dangerous due to possible penetration into the lungs. The efficiency is measured by the number of particles blocked by the pore structure after passing though the filter. To study the penetration into pores by nanoparticles suspended in a fluid, a stochastic transport theory based on an atomistic model is used to calculate particle density and flow within the pores, resulting pressure gradient, and filter efficiency. The importance of pore size relative to particle diameter and of the parameters of the pore wall interactions are investigated. The theory is applied to aerosols in fibrous filters and found to reproduce common trends in measurements. As particles enter the initially empty pores on relaxation to the steady state the small penetration measured at the onset of filtration increases faster in time the smaller the nanoparticle diameter. Control of pollution by filtration is achieved by strong repulsion of pore walls for particle diameters greater than twice the effective pore width. For smaller nanoparticles the steady-state efficiency decreases as the pore wall interactions weaken. Effective efficiency is increased when the suspended nanoparticles inside the pores combine into clusters of sizes greater than the filter channel width.

Complying with the resource requirements of ISO/IEC 17025:2017 in Indonesian calibration and testing laboratories: current challenges and future directions

Compliance with all the requirements in the ISO/IEC 17025:2017 is crucial for testing and calibration laboratories in assuring the quality of measurement conducted in their laboratories. The latest version of the ISO/IEC 17025:2017 presents a different structure compared to the previous version, ISO/IEC 17025:2005. Therefore, amendments in the quality documents and the operational procedures in the laboratories are urgently required. However, not all laboratories' personnel understand this new standard and know how to implement or incorporate this new version standard with their old version documents and operational procedures. It causes a problem for the testing and calibration laboratories, especially in Indonesia. This study is expected to provide enlightenment and hints for the laboratories struggling to comply with the ISO/IEC 17025:2017.

New, Fully Implantable Device for Selective Clearance of CSF-Target Molecules: Proof of Concept in a Murine Model of Alzheimer’s Disease

We have previously proposed a radical change in the current strategy to clear pathogenic proteins from the central nervous system (CNS) based on the cerebrospinal fluid (CSF)-sink therapeutic strategy, whereby pathogenic proteins can be removed directly from the CNS via CSF. To this aim, we designed and manufactured an implantable device for selective and continuous apheresis of CSF enabling, in combination with anti-amyloid-beta (Aβ) monoclonal antibodies (mAb), the clearance of Aβ from the CSF. Here, we provide the first proof of concept in the APP/PS1 mouse model of Alzheimer’s disease (AD). Devices were implanted in twenty-four mice (seventeen APP/PS1 and seven Wt) with low rates of complications. We confirmed that the apheresis module is permeable to the Aβ peptide and impermeable to mAb. Moreover, our results showed that continuous clearance of soluble Aβ from the CSF for a few weeks decreases cortical Aβ plaques. Thus, we conclude that this intervention is feasible and may provide important advantages in terms of safety and efficacy.

Nanolattice-Forming Hybrid Collagens in Protective Shark Egg Cases

Nanoscopic structural control with long-range ordering remains a profound challenge in nanomaterial fabrication. The nanoarchitectured egg cases of elasmobranchs rely on a hierarchically ordered latticework for their protective function─serving as an exemplary system for nanoscale self-assembly. Although the proteinaceous precursors are known to undergo intermediate liquid crystalline phase transitions before being structurally arrested in the final nanolattice architecture, their sequences have so far remained unknown. By leveraging RNA-seq and proteomic techniques, we identified a cohort of nanolattice-forming proteins comprising a collagenous midblock flanked by domains typically associated with innate immunity and network-forming collagens. Structurally homologous proteins were found in the genomes of other egg-case-producing cartilaginous fishes, suggesting a conserved molecular self-assembly strategy. The identity and stabilizing role of cross-links were subsequently elucidated using mass spectrometry and in situ small-angle X-ray scattering. Our findings provide a new design approach for protein-based liquid crystalline elastomers and the self-assembly of nanolattices.

Freestanding non-covalent thin films of the propeller-shaped polycyclic aromatic hydrocarbon decacyclene

Molecularly thin, nanoporous thin films are of paramount importance in material sciences. Their use in a wide range of applications requires control over their chemical functionalities, which is difficult to achieve using current production methods. Here, the small polycyclic aromatic hydrocarbon decacyclene is used to form molecular thin films, without requiring covalent crosslinking of any kind. The 2.5 nm thin films are mechanically stable, able to be free-standing over micrometer distances, held together solely by supramolecular interactions. Using a combination of computational chemistry and microscopic imaging techniques, thin films are studied on both a molecular and microscopic scale. Their mechanical strength is quantified using AFM nanoindentation, showing their capability of withstanding a point load of 26 ± 9 nN, when freely spanning over a 1 μm aperture, with a corresponding Young’s modulus of 6 ± 4 GPa. Our thin films constitute free-standing, non-covalent thin films based on a small PAH.

Molecularly thin films are important in material sciences but their use in a wide range of applications requires control over their chemical functionalities, which is difficult to achieve. Here, the authors use decacyclene to form such freestanding and mechanically stable molecular films held together by supramolecular interactions without requiring covalent crosslinking of any kind

Block Copolymer Nanopatterning for Nonsemiconductor Device Applications

Block copolymer (BCP) nanopatterning has emerged as a versatile nanoscale fabrication tool for semiconductor devices and other applications, because of its ability to organize well-defined, periodic nanostructures with a critical dimension of 5-100 nm. While the most promising application field of BCP nanopatterning has been semiconductor devices, the versatility of BCPs has also led to enormous interest from a broad spectrum of other application areas. In particular, the intrinsically low cost and straightforward processing of BCP nanopatterning have been widely recognized for their large-area parallel formation of dense nanoscale features, which clearly contrasts that of sophisticated processing steps of the typical photolithographic process, including EUV lithography. In this Review, we highlight the recent progress in the field of BCP nanopatterning for various nonsemiconductor applications. Notable examples relying on BCP nanopatterning, including nanocatalysts, sensors, optics, energy devices, membranes, surface modifications and other emerging applications, are summarized. We further discuss the current limitations of BCP nanopatterning and suggest future research directions to open up new potential application fields.

Recent Advancements in the Fabrication of Functional Nanoporous Materials and Their Biomedical Applications

Functional nanoporous materials are categorized as an important class of nanostructured materials because of their tunable porosity and pore geometry (size, shape, and distribution) and their unique chemical and physical properties as compared with other nanostructures and bulk counterparts. Progress in developing a broad spectrum of nanoporous materials has accelerated their use for extensive applications in catalysis, sensing, separation, and environmental, energy, and biomedical areas. The purpose of this review is to provide recent advances in synthesis strategies for designing ordered or hierarchical nanoporous materials of tunable porosity and complex architectures. Furthermore, we briefly highlight working principles, potential pitfalls, experimental challenges, and limitations associated with nanoporous material fabrication strategies. Finally, we give a forward look at how digitally controlled additive manufacturing may overcome existing obstacles to guide the design and development of next-generation nanoporous materials with predefined properties for industrial manufacturing and applications.

Structural, biocompatibility, and antibacterial properties of Ge-DLC nanocomposite for biomedical applications

Integrative production of new nanocomposites has been used to enhance favorable features of biomaterials for unlocking ultimate potential of different molecules. In the present study, advantageous properties of diamond like carbons (DLC) and germanium (Ge) like greater biocompatibility and antibacterial attributes were aimed to combined into a thin film. For this purpose, 400 nm DLC-Ge nanocomposite was coated on the borosilicate glasses via the magnetron sputtering and surface characteristics was analyzed by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and The Raman spectrum. Biocompatibility analysis were performed by 3-(4,5-Dimethylthiazol-2-yl) (MTT) cell viability assay and Hoechst 33258 fluorescent staining genotoxicity assessments on the human fibroblast cell line (HDFa). Finally, antibacterial properties of DLC-Ge nanocomposite coatings were investigated by Pseudomonas aeruginosa (ATCC 27853) and Staphylococcus aureus (ATCC 25923) bacterial attachment analysis. As a result of magnetron sputtering coating, nearly 400 nm thick DLC-Ge nanocomposite film showed a smooth, a non-porous, and a dense characteristic. Cell viability analysis showed that Ge-DLC coatings permits %95 cell surface growth of fibroblast cells. Also, there were no significant difference in aspect of nuclear abnormalities compared to the (-) control which showed nonmutagenic features of the thin film. Finally, antibacterial attachment analysis put forth that Ge-DLC coatings inhibits bacterial adhesion as %40 and %25 rates for P. aeruginosa and S. aureus bacterial strains, respectively. From these results, DLC-Ge nanocomposites could be proposed as a potential new biomaterial for various biomedical applications.

Investigation of Duplex Brass Membranes with Metallography, Permeability and Treatments: Work-Hardening, Annealing and Quenching

This paper consists of the fabrication and investigation of metal membranes and the study of their behaviour and applications in gas separation processes. The scope is to produce and characterize the porous crystal structure of brass alloy (standardization: DIN 17660) membranes and measure their permeability with helium as a penetrant medium. Another part of this study is to alter the brass alloy’s structure throughout metallurgical treatments and investigate how the permeability is allied to the structure’s alteration. This work merges the knowledge and technology of inorganic porous materials science in metallurgy. The novelty of the current research resides in the process to alternate the brass alloy structure throughout metallurgical treatments and how it is allied to the permeability of the membrane, which is of interest to be investigated. The results of the research are analysed and compared conducting the final inferences. All metallurgical treatments resulted in low permeability values when compared to a non-treated specimen. Specifically, the drop in permeance ranged from 76 up to 99.56%. It is noted that consecutive treatments contributed to even further decreases.

Tuning SLOCK toward Chronic Disease Diagnostics and Management: Label-free Sweat Interleukin-31 Detection

SLOCK (sensor for circadian clock) is an electrochemical sweat-based biosensing platform designed for the diagnosis and management of circadian abnormalities. Previously, the SLOCK platform was designed to detect adrenal steroids, cortisol, and DHEA for tracking the circadian rhythm. This work aims at tuning this SLOCK platform toward the detection of the cytokine, interleukin-31, for building a noninvasive, chronic disease diagnostics and management platform. This research provides a detailed characterization of the sensing surface and immunochemistry. The results show that SLOCK has good sensitivity to IL-31 concentrations in synthetic and human sweat. The limit of detection is 50 and 100 pg/mL for synthetic and human sweat, respectively. The dynamic range of the system is 50-1000 pg/mL, which encompasses the physiological ranges of 150-620 pg/mL. This is the first demonstration of sweat-based, label-free, electrochemical detection of IL-31. In addition to this, the data show good correlation (R 2 > 0.95) for the signal sensitivity to biomarker concentration. Finally, cross-reactivity studies highlight the specificity of SLOCK even in the presence of highly cross-reactive species. Thus, this novel SLOCK biosensor can be successfully used to track IL-31 in a sensitive and noninvasive manner and could be used to identify chronic pathophysiologies present in the body.

Polymeric membranes for biomedical applications

The rapid development of nanotechnology paved the way for further expansion of polymer chemistry and the fabrication of advanced polymeric membranes. Such modifications allowed enhancing or adding some unique properties, including mechanical strength, excellent biocompatibility, easily controlled degradability, and biological activity. This chapter discusses various applications of polymeric membranes in three significant areas of biomedicine, including tissue engineering, drug delivery systems, and diagnostics. It is intended to highlight here possible ways of improvement the properties of polymeric membranes, by modifying with other polymers, functional groups, compounds, drugs, bioactive components, and nanomaterials.

Advances in Micro/Nanoporous Membranes for Biomedical Engineering

Porous membrane materials at the micro/nanoscale have exhibited practical and potential value for extensive biological and medical applications associated with filtration and isolation, cell separation and sorting, micro-arrangement, in-vitro tissue reconstruction, high-throughput manipulation and analysis, and real-time sensing. Herein, an overview of technological development of micro/nanoporous membranes (M/N-PMs) is provided. Various membrane types and the progress documented in membrane fabrication techniques, including the electrochemical-etching, laser-based technology, microcontact printing, electron beam lithography, imprinting, capillary force lithography, spin coating, and microfluidic molding are described. Their key features, achievements, and limitations associated with micro/nanoporous membrane (M/N-PM) preparation are discussed. The recently popularized applications of M/N-PMs in biomedical engineering involving the separation of cells and biomolecules, bioparticle operations, biomimicking, micropatterning, bioassay, and biosensing are explored too. Finally, the challenges that need to be overcome for M/N-PM fabrication and future applications are highlighted.

Short-Pulse Lasers: A Versatile Tool in Creating Novel Nano-/Micro-Structures and Compositional Analysis for Healthcare and Wellbeing Challenges

Driven by flexibility, precision, repeatability and eco-friendliness, laser-based technologies have attracted great interest to engineer or to analyze materials in various fields including energy, environment, biology and medicine. A major advantage of laser processing relies on the ability to directly structure matter at different scales and to prepare novel materials with unique physical and chemical properties. It is also a contact-free approach that makes it possible to work in inert or reactive liquid or gaseous environment. This leads today to a unique opportunity for designing, fabricating and even analyzing novel complex bio-systems. To illustrate this potential, in this paper, we gather our recent research on four types of laser-based methods relevant for nano-/micro-scale applications. First, we present and discuss pulsed laser ablation in liquid, exploited today for synthetizing ultraclean "bare" nanoparticles attractive for medicine and tissue engineering applications. Second, we discuss robust methods for rapid surface and bulk machining (subtractive manufacturing) at different scales by laser ablation. Among them, the microsphere-assisted laser surface engineering is detailed for its appropriateness to design structured substrates with hierarchically periodic patterns at nano-/micro-scale without chemical treatments. Third, we address the laser-induced forward transfer, a technology based on direct laser printing, to transfer and assemble a multitude of materials (additive structuring), including biological moiety without alteration of functionality. Finally, the fourth method is about chemical analysis: we present the potential of laser-induced breakdown spectroscopy, providing a unique tool for contact-free and space-resolved elemental analysis of organic materials. Overall, we present and discuss the prospect and complementarity of emerging reliable laser technologies, to address challenges in materials' preparation relevant for the development of innovative multi-scale and multi-material platforms for bio-applications.

Development of a Mechanically Strong Nondegradable Protein Hydrogel with a Sponge-Like Morphology

Protein-based hydrogels are important functional materials with many potential applications. However, the relatively small pore size and poor mechanical properties substantially limit their application. Here a superporous bovine serum albumin (BSA) hydrogel is prepared with high porosity and interconnectivity by using BSA and 1,2,7,8-diepoxyoctane (DEO). The equilibrium water contents of hydrogels can reach 76.5%. Moreover, the BSA hydrogels show excellent mechanical properties and excellent deformation recoverability, with a maximum compression modulus of 50 MPa at 75% strain and no residual strain generated after 500 cyclic compression tests. The resulting BSA hydrogel has excellent biocompatibility for cell adherence and is nonbiodegradable for 40 weeks. More importantly, the BSA hydrogel exhibits excellent hemostatic ability, with hemostatic times in a rabbit ear artery and rabbit liver of 33 and 28 s, respectively. Therefore, BSA hydrogels have potential applications as painless nonadherent wound dressings and implant materials for plastic surgery.

Chemically-Gated and Sustained Molecular Transport through Nanoporous Gold Thin Films in Biofouling Conditions

Sustained release and replenishment of the drug depot are essential for the long-term functionality of implantable drug-delivery devices. This study demonstrates the use nanoporous gold (np-Au) thin films for in-plane transport of fluorescein (a small-molecule drug surrogate) over large (mm-scale) distances from a distal reservoir to the site of delivery, thereby establishing a constant flux of molecular release. In the absence of halides, the fluorescein transport is negligible due to a strong non-specific interaction of fluorescein with the pore walls. However, in the presence of physiologically relevant concentration of ions, halides preferentially adsorb onto the gold surface, minimizing the fluorescein–gold interactions and thus enabling in-plane fluorescein transport. In addition, the nanoporous film serves as an intrinsic size-exclusion matrix and allows for sustained release in biofouling conditions (dilute serum). The molecular release is reproducibly controlled by gating it in response to the presence of halides at the reservoir (source) and the release site (sink) without external triggers (e.g., electrical and mechanical).

Power-law coarsening in network-forming phase separation governed by mechanical relaxation

A space-spanning network structure is a basic morphology in phase separation of soft and biomatter, alongside a droplet one. Despite its fundamental and industrial importance, the physical principle underlying such network-forming phase separation remains elusive. Here, we study the network coarsening during gas-liquid-type phase separation of colloidal suspensions and pure fluids, by hydrodynamic and molecular dynamics simulations, respectively. For both, the detailed analyses of the pore sizes and strain field reveal the self-similar network coarsening and the unconventional power-law growth more than a decade according to ℓ ∝ t1/2, where ℓ is the characteristic pore size and t is the elapsed time. We find that phase-separation dynamics is controlled by mechanical relaxation of the network-forming dense phase, whose limiting process is permeation flow of the solvent for colloidal suspensions and heat transport for pure fluids. This universal coarsening law would contribute to the fundamental physical understanding of network-forming phase separation.

Demonstration of sweat-based circadian diagnostic capability of SLOCK using electrochemical detection modalities

SLOCK is a sweat-based circadian diagnostic platform used for mapping the user's chronobiology via cortisol and DHEA. In this work, we have demonstrated the detection capabilities of this sweat-based sensing platform using two electrochemical sensing modalities: Electrochemical Impedance Spectroscopy (EIS) and chronoamperometry. Wicking simulations for vertical versus horizontal flow patterns under potential bias were evaluated using COMSOL Multiphysics®. This work also highlights the biorecognition element characterization using Surface Plasmon Resonance (SPR) and FTIR. Sensor platform was evaluated for biomarker concentrations using doses spanning physiological ranges of 8-141 ng ml-1 and 2-131 ng ml-1 for cortisol and DHEA, respectively. Detailed analysis of impedance data is supported with electrochemical fitting of circuit components related to the biosensing process. Finally, human subject-based studies have been performed to understand the effect of sweating rate with respect to gland density on biosensing. Also, on-body mechanical resiliency studies have been performed to highlight the flexibility of this serpentine electrode-based sensing platform. The platform responds sensitively to the amount of circadian relevant biomarkers in the system with a limit of detection of 0.1 ng ml-1 for both cortisol and DHEA. Thus, the SLOCK platform offers to be an attractive vessel for facilitating the electrochemical detection of circadian relevant biomarkers and for self-monitoring of user's chronobiology.

Nanoporous Films with Photoswitchable Absorption Kinetics Based on Polymerizable Columnar Discotic Liquid Crystals

A photoresponsive nanoporous polymer film has been produced from the templated self-assembly of a columnar liquid crystal containing azo units. A liquid crystalline complex of polymerizable azobenzoic acid and a tris-benzimidazolyl benzene template molecule was cross-linked via thiol-ene radical copolymerization with dodecanedithiol. Subsequent removal of the template yielded nanoporous polymer films with pores of approximately 1 nm in diameter. Both trans-cis and cis-trans photoisomerizations of azobenzoic acid took place in the porous films. At room temperature, the cis isomer was sufficiently long-lived to establish a difference in dye absorption kinetics of the two isomers. The cationic dye rhodamine 6G was bound to both isomers, but the rate of binding to films enriched in the cis isomer was 8 times faster.

Catalytic Activity of Ni, Co, Mo Supported Anodic Aluminum Oxide Nanocomposites

Nanostructured catalysts based on porous aluminum oxide (PAO) and some 3d metals, such as: nickel, cobalt, and molybdenum, have been obtained by anodic oxidation and impregnation. The synthesis of porous aluminum oxide with a highly ordered pore structure with pore sizes of 50 nm and a thickness of 50 µm is carried out by the method of two-stage anodic oxidation. The catalysts are obtained by impregnation of 3d metals into nanosized pores of aluminum oxide. The obtained catalysts based on nickel and porous Al2O3 are studied by scanning electron microscopy (SEM-EDX). The results of SEM-EDX analysis shows that a spongy structure with filament sizes of 100 nanometers containing particles of 3d metals formed on the surface of the aluminum oxide matrix. The results are presented on the activity of nickel and heterogenic cobalt and molybdenum nanoparticles in the reaction of hydrogenation of hexene to hexane. The results show that the yield temperature of the hexane is decreased and the yield of hexane is observed at 200 °C with Ni/Al2O3 catalysts, and a similar yield of hexane mass is achieved at temperatures higher than 250 °C with Co-Mo/Al2O3 and traditional nickel catalysts on kieselguhr. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Biocompatibility of α-Al2O3 Ceramic Substrates with Human Neural Precursor Cells

BACKGROUND

Biocompatible materials-topography could be used for the construction of scaffolds allowing the three-dimensional (3D) organization of human stem cells into functional tissue-like structures with a defined architecture.

METHODS

Structural characterization of an alumina-based substrate was performed through XRD, Brunauer-Emmett-Teller (BET) analysis, scanning electron microscopy (SEM), and wettability measurements. Biocompatibility of the substrate was assessed by measuring the proliferation and differentiation of human neural precursor stem cells (NPCs).

RESULTS

α-Al₂O₃ is a ceramic material with crystallite size of 40 nm; its surface consists of aggregates in the range of 8-22 μm which forms a rough surface in the microscale with 1-8 μm cavities. The non-calcined material has a surface area of 5.5 m²/gr and pore size distribution of 20 nm, which is eliminated in the calcined structure. Thus, the pore network on the surface and the body of the ceramic becomes more water proof, as indicated by wettability measurements. The alumina-based substrate supported the proliferation of human NPCs and their differentiation into functional neurons.

CONCLUSIONS

Our work indicates the potential use of alumina for the construction of 3D engineered biosystems utilizing human neurons. Such systems may be useful for diagnostic purposes, drug testing, or biotechnological applications.

Development of Nanoporous AAO Membrane for Nano Filtration Using the Acoustophoresis Method

A concept of a nanoporous anodic aluminum oxide (AAO) membrane as a vibro-active micro/nano-filter in a micro hydro mechanical system for the filtration, separation, and manipulation of bioparticles is reported in this paper. For the fabrication of a nanoporous AAO, a two-step mild anodization (MA) and hard anodization (HA) technique was used. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) were used to analyze the surface morphology of nanoporous AAO. A nanoporous structure with a pore diameter in the range of 50–90 nm, an interpore distance of 110 nm, and an oxide layer thickness of 0.12 mm with 60.72% porosity was obtained. Fourier-transform infrared spectroscopy (FTIR) and energy-dispersive X-ray spectroscopy (EDS) were employed to evaluate AAO chemical properties. The obtained results showed that the AAO structure is of hexagonal symmetry and showed where Al₂O₃ is dominant. The hydrophobic properties of the nanoporous surface were characterized by water contact angle measurement. It was observed that the surface of the nanoporous AAO membrane is hydrophilic. Furthermore, to determine whether a nanomembrane could function as a vibro-active nano filter, a numerical simulation was performed using COMSOL Multiphysics 5.4 (COMSOL Inc, Stockholm, Sweden). Here, a membrane was excited at a frequency range of 0–100 kHz for surface acoustics wave (SAW) distribution on the surface of the nanoporous AAO using a PZT 5H cylinder (Piezo Hannas, Wuhan, China). The SAW, standing acoustic waves, and travelling acoustic waves of different wavelengths were excited to the fabricated AAO membrane and the results were compared with experimental ones, obtained from non-destructive testing method 3D scanning vibrometer (PSV-500-3D-HV, Polytec GmbH, Waldbronn, Germany) and holographic interferometry system (PRISM, Hy-Tech Forming Systems (USA), Phoenix, AZ, USA). Finally, a simulation of a single nanotube was performed to analyze the acoustic pressure distribution and time, needed to center nanoparticles in the nanotube.

Hierarchically Structured Porous Piezoelectric Polymer Nanofibers for Energy Harvesting

Hierarchically porous piezoelectric polymer nanofibers are prepared through precise control over the thermodynamics and kinetics of liquid-liquid phase separation of nonsolvent (water) in poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)) solution. Hierarchy is achieved by fabricating fibers with pores only on the surface of the fiber, or pores only inside the fiber with a closed surface, or pores that are homogeneously distributed in both the volume and surface of the nanofiber. For the fabrication of hierarchically porous nanofibers, guidelines are formulated. A detailed experimental and simulation study of the influence of different porosities on the electrical output of piezoelectric nanogenerators is presented. It is shown that bulk porosity significantly increases the power output of the comprising nanogenerator, whereas surface porosity deteriorates electrical performance. Finite element method simulations attribute the better performance to increased volumetric strain in bulk porous nanofibers.

Engineering osteogenic microenvironments by combination of multilayers from collagen type I and chondroitin sulfate with novel cationic liposomes

Cationic liposomes composed of a novel lipid (N-{6-amino-1-[N-(9Z) -octadec9-enylamino] -1-oxohexan-(2S) -2-yl} -N'- {2- [N, N-bis(2-aminoethyl) amino] ethyl} -2-hexadecylpropandiamide) (OO4) and dioleoylphosphatidylethanolamine (DOPE) possess high amounts of amino groups and are promising systems for lipofection. Moreover, these cationic liposomes can also be used as a polycationic entity in multilayer formation using layer-by-layer technique (LbL), which is a method to fabricate surface coatings by alternating adsorption of polyanions and polycations. Since liposomes are suitable for endocytosis by or fusion with cells, controlled release of their cargo on site is possible. Here, a polyelectrolyte multilayer (PEM) system was designed of chondroitin sulfate (CS) and collagen type I (Col I) by LbL technique with OO4/DOPE liposomes embedded in the terminal layers to create an osteogenic microenvironment. Both, the composition of PEM and cargo of the liposomes were used to promote osteogenic differentiation of C2C12 myoblasts as in vitro model. The internalization of cargo-loaded liposomes from the PEM into C2C12 cells was studied using lipophilic (Rhodamine-DOPE conjugate) and hydrophilic (Texas Red-labeled dextran) model compounds. Besides, the use of Col I and CS should mimic the extracellular matrix of bone for future applications such as bone replacement therapies. Physicochemical studies of PEM were done to characterize the layer growth, thickness, and topography. The adhesion of myoblast cells was also evaluated whereby the benefit of a cover layer of CS and finally Col I above the liposome layer was demonstrated. As proof of concept, OO4/DOPE liposomes were loaded with dexamethasone, a compound that can induce osteogenic differentiation. A successful induction of osteogenic differentiation of C2C12 cells with the novel designed liposome-loaded PEM system was shown. These findings indicate that designed OH4/DOPE loaded PEMs have a high potential to be used as drug delivery or transfection system for implant coating in the field of bone regeneration and other applications.

Fabrication of Hybrid Membranes Containing Nylon-11 and Organic Semiconductor Particles with Potential Applications in Molecular Electronics

Chemical degradation is a major disadvantage in the development of organic semiconductors. This work proposes the manufacture and characterization of organic semiconductor membranes in order to prevent semiconductor properties decreasing. Semiconductor membranes consisting of Nylon-11 and particles of π-conjugated molecular semiconductors were manufactured by high-vacuum evaporation followed by thermal relaxation. Initially, and with the aim of obtaining semiconductor particles, bulk heterojunction (BHJ) was carried out using green chemistry techniques between the zinc phthalocyanine (ZnPc) and the zinc hexadecafluoro-phthalocyanine (F₁₆ZnPc) as n-type molecular semiconductors with the p-type molecular semiconductor dibenzotetrathiafulvalene (DBTTF). Consequently, the π-conjugated semiconductors particles were embedded in a Nylon-11 matrix and characterized, both structurally and considering their optical and electrical properties. Thin films of these materials were manufactured in order to comparatively study the membranes and precursor semiconductor particles. The membranes presented bandgap (E_g) values that were lower than those obtained in the films, which is an indicator of an improvement in their semiconductor capacity. Finally, the membranes were subjected to accelerated lighting conditions, to determine the stability of the polymer and the operating capacity of the membrane. After fatigue conditions, the electrical behavior of the proposed semiconductor membranes remained practically unaltered; therefore, they could have potential applications in molecular electronics. The chemical stability of membranes, which did not degrade in their polymer compound, nor in the semiconductor, was monitored by IR spectroscopy.

LabVIEW-Based Automated Setup for Interferometric Refractive Index Probing

In the paper, we explain an automated LabVIEW-controlled setup that enables interferometric measurement of refractive indices in crystalline materials using a laser light source. The setup combines a mechanical system, a microcomputer-controlled gearless drive, a Michelson interferometer, an optical detector, a data acquisition system, and a LabVIEW virtual instrument for an accurate nondestructive determination of the refractive index of given plane-parallel samples. We explain the concept, implementation, and hardware/software peculiarities of the developed system. Test experiments on different crystals yielded results that are in good agreement with available reference data. The range of potential applications of the proposed setup extends from fundamental optical research to biophotonics instrumentation, where efficient delivery of light is of crucial importance and reliable automated probing tools are needed for optical component characterization.

Two-dimensional Simulation of Motion of Red Blood Cells with Deterministic Lateral Displacement Devices

Deterministic lateral displacement (DLD) technology has great potential for the separation, enrichment, and sorting of red blood cells (RBCs). This paper presents a numerical simulation of the motion of RBCs using DLD devices with different pillar shapes and gap configurations. We studied the effect of the pillar shape, row shift, and pillar diameter on the performance of RBC separation. The numerical results show that the RBCs enter "displacement mode" under conditions of low row-shift (∆λ < 1.4 µm) and "zigzag mode" with large row shift (∆λ > 1.5 µm). RBCs can pass the pillar array when the size of the pillar (d > 6 µm) is larger than the cell size. We show that these conclusions can be helpful for the design of a reliable DLD microfluidic device for the separation of RBCs.

Preliminary Study of Ge-DLC Nanocomposite Biomaterials Prepared by Laser Codeposition

This paper deals with the synthesis and study of the properties of germanium-doped diamond-like carbon (DLC) films. For deposition of doped DLC films, hybrid laser technology was used. Using two deposition lasers, it was possible to arrange the dopant concentrations by varying the laser repetition rate. Doped films of Ge concentrations from 0 at.% to 12 at.% were prepared on Si (100) and fused silica (FS) substrates at room temperature. Film properties, such as growth rate, roughness, scanning electron microscopy (SEM) morphology, wavelength dependent X-ray spectroscopy (WDS) composition, VIS-near infrared (IR) transmittance, and biological properties (cytotoxicity, effects on cellular morphology, and ability to produce reactive oxygen species (ROS)) were studied in relation to codeposition conditions and dopant concentrations. The analysis showed that Ge-DLC films exhibit cytotoxicity for higher Ge doping.

Nanoenabled Bioseparations: Current Developments and Future Prospects

The use of nanomaterials in bioseparations has been recently introduced to overcome the drawbacks of the conventional methods. Different forms of nanomaterials, particularly magnetic nanoparticles (MNPs), carbon nanotubes (CNTs), casted nanoporous membranes, and electrospun nanofiber membranes were utilized in biological separation for the aim of production of different biomolecules such as proteins, amino acids, nucleic acids, and enzymes. This paper critically reviews the state-of-the-art efforts undertaken in this regard, with emphasis on the synthesis and performance evaluation of each nanoform. Challenges and future prospects in developing nanoenabled bioseparations are also discussed, for the purpose of highlighting potential advances in the synthesis and fabrication of novel nanomaterials as well as in the design of efficient nanoenabled processes for separating a wide spectrum of biomolecules.

Responsive Nanoporous Membranes with Size Selectivity and Charge Rejection from Self-Assembly of Polyelectrolyte "Hairy" Nanoparticles

We report the preparation and characterization of charged nanoporous membranes by self-assembly of "hairy" silica nanoparticles (HNPs) functionalized with polyelectrolyte copolymer brushes. We show that HNP membranes possess high water flux, have well-defined pore sizes, and rejection up to 80% of charged species in solution. The properties of these membranes can be tuned by controlling the length and composition of polymer brushes and the electrolyte concentration in solution. We demonstrate that membrane pore sizes undergo changes of up to 40% in response to changes in the ionic strength of the salt solution. Using MD computer simulations of a coarse-grained model, we link these tunable properties to the conformations of polymer chains in the spaces between randomly packed HNPs. As polymer length increases, the polymers fill the interparticle gaps, and the pore size decreases markedly. On the basis of their straightforward fabrication and tunable properties, HNP membranes may find applications in size- and charge-selective separations, water desalination, and responsive devices.

State-of-the-Art and Future Prospects for Atomically Thin Membranes from 2D Materials

Atomically thin 2D materials, such as graphene, hexagonal boron-nitride, and others, offer new possibilities for ultrathin barrier and membrane applications. While the impermeability of pristine 2D materials to gas molecules, such as He, allows the realization of the thinnest physical barrier, nanoscale vacancy defects in the 2D material lattice manifest as nanopores in an atomically thin membrane. Such nanoporous atomically thin membranes (NATMs) present potential for enabling ultrahigh permeance and selectivity in a wide range of novel separation processes. Herein, the transport properties observed in NATMs are described and recent experimental progress achieved in their fabrication is summarized. Some of the challenges in NATM scale-up for practical applications are highlighted and several opportunities are identified, including the possibility of blending traditional membrane-processing approaches. Finally, a technological roadmap is presented with a contextual discussion for NATMs to progress from research to applications.