Pull-off Force Measurements between Rough Surfaces by Atomic Force Microscopy

How Much Data Are Enough? Toward Statistically Robust Adhesion Experiments by Atomic Force Microscopy

Direct force measurements by atomic force microscopy (AFM) have become an indispensable analytical tool in the last decades. Force measurements have been widely used for adhesion measurements, often in combination with the colloidal probe technique. For the latter technique, a colloidal particle is attached to the end of an AFM cantilever, proving great flexibility in terms of colloid/surface interaction to be studied. Interestingly, the question of how much data is necessary to obtain statistically reliable results has been addressed in this context only sparsely. By contrast, the value and necessity of determining and reporting distributions of adhesion forces has been widely accepted. Here, simple statistical methods of the experimental design have been applied to address this question. It has been demonstrated that it is possible to determine an optimal number of force curves even during data acquisition. This approach would be essential to prevent oversampling of data. Moreover, it allows to address questions like heterogeneity of the sample in a more reliable or less time-consuming way. In AFM measurements with colloidal probes, most statistical variation results from the surface roughness of the probe particle. In this case, the use of different colloidal particles is important, which can be achieved by techniques such as fluidic force microscopy (FluidFM). The latter enables to combine a real-time determination of the required data size and high-throughput techniques of unattended measurements, which will open new fields of analysis.

Enhanced Electrostatic Dust Removal from Solar Panels Using Transparent Conductive Nano-Textured Surfaces

Dust accumulation on solar panels is a mjor operational challenge faced by the photovoltaic industry. Removing dust using water-based cleaning is expensive and unsustainable. Dust repulsion via charge induction is an efficient way to clean solar panels and recover power output without consuming any water. However, it is still challenging to remove particles of ≈30 µm and smaller because Van der Waals force of adhesion dominates electrostatic force of repulsion. Here, the study proposes nano-textured, transparent, electrically conductive glass surfaces to significantly enhance electrostatic dust removal for particles smaller than ≈30 µm. We perform atomic force microscopy pull-off force experiments and demonstrates that nano-textured surfaces reduce the force of adhesion of silica micro-particles by up to 2 orders of magnitude compared to un-textured surfaces from 460 to 8.6 nN. We show that reduced adhesion on nano-textured surfaces results in significantly better dust removal of small particles compared to non-textured or micro-textured surfaces, reducing the surface coverage from 35% to 10%. We fabricate transparent, electrically conductive, nano-textured glass that can be retrofitted on solar panel surfaces using copper nano-mask based scalable nano-fabrication technique and shows that 90% of lost power output for particles smaller than ≈10 µm can be recovered.

The Effects of Short-Range Intermolecular Repulsive Forces on Hamaker Constant Estimation Using Atomic Force Microscopy

The atomic force microscope (AFM), as it is able to characterize surface topography as well determine the AFM cantilever tip-surface force, proves effective at estimating the value of the Hamaker constant, A, for a given solid material. Two main AFM-based methods have been proposed for estimating values of A. In the approach-to-contact (AtC) method, Hamaker constants are inferred from the deflections at which the AFM tip first jumps into contact with the substrate. In the pull-off (PO) method, the deflections that arise when the AFM tip is finally pulled away from the substrate are used to estimate values of A. In prior applications of these two methods, the short-range intermolecular repulsive forces that are known to arise between the AFM tip and the substrate were, however, ignored. Upon invoking a physically relevant description of these short-range and steeply repulsive forces, we investigate the effects of repulsive interactions on the values of A estimated from the existing AtC and PO methods when applied to neutrally charged systems under low humidity or vacuum conditions. For experimentally relevant surfaces, we find that repulsive forces have a modest effect on the AtC method, although they still need to be accounted for in order to generate improved estimates of the Hamaker constant. On the other hand, repulsive forces have a significant effect on the Hamaker constants inferred from the PO method, and must be properly accounted for when using this approach. Our analysis also includes an explicit incorporation of surface roughness into the PO method, which is not typically done in most prior applications of the PO method.

A Novel Nano-Spherical Tip for Improving Precision in Elastic Modulus Measurements of Polymer Materials via Atomic Force Microscopy

Micro-nano-scale mechanical properties are vital for engineering and biological materials. The elastic modulus is generally measured by processing the force-indentation curves obtained by atomic force microscopy (AFM). However, the measurement precision is largely affected by tip shape, tip wear, sample morphology, and the contact model. In such research, it has been found that the radius of the sharp tip increases due to wear during contact scanning, affecting elastic modulus calculations. For flat-ended tips, it is difficult to identify the contact condition, leading to inaccurate results. Our research team has invented a nano-spherical tip, obtained by implanting focused helium ions into a silicon microcantilever, causing it to expand into a silicon nanosphere. This nano-spherical tip has the advantages of sub-micro size and a smooth spherical surface. Comparative tests of the elastic modulus measurement were conducted on polytetrafluoroethylene (PTFE) and polypropylene (PP) using these three tips. Overall, the experimental results show that our nano-spherical tip with a consistent tip radius, symmetrical geometric shape, and resistance to wear and contamination can improve precision in elastic modulus measurements of polymer materials.

Nanoscale-roughness influence on pull-off adhesion force in liquid and air

The pull-off adhesion force was measured by atomic force microscopy in sphere-plate geometry in water where a capillarylike behavior develops due to nanobubbles and was compared to the corresponding capillary adhesion in air. The sphere and the plate were coated with gold, and the pull-off adhesion force was measured as a function of the evolving surface roughness of the plate, and the retraction velocity of the interacting surfaces. In absolute magnitude, the pull-off force in air is larger than that in liquid by an order of magnitude or more, but in both cases, the pull-off force follows a monotonic decrease with increasing roughness. However, the relative decrement of the adhesion force in water was approximately 300%, and significantly higher than that in air for the same change of the rms roughness in the range ∼7-14 nm. Finally, the adhesion force in water shows a relatively complex dependence on the retraction velocity of the interacting surfaces as the roughness increases due to possible deformation of the nanobubbles and the bridges they form between the surfaces.

Understanding the role of magnesium stearate in lowering punch sticking propensity of drugs during compression

The sticking of active pharmaceutical ingredient (API) to the surfaces of compaction tooling, frequently referred to as punch sticking, causes costly downtime or product failures in commercial tablet manufacturing. Magnesium stearate (MgSt) is a common tablet lubricant known to ameliorate the sticking problem, even though there exist exceptions. The mechanism by which MgSt lowers punch sticking propensity (PSP) by covering API surface is sensible but not yet experimentally proven. This work was aimed at elucidating the link between PSP and surface area coverage (SAC) of tablets by MgSt, in relation to some key formulation properties and process parameters, namely MgSt concentration, API loading, API particle size, and mixing conditions. The study was conducted using two model APIs with known high PSPs, tafamidis (TAF) and ertugliflozin-pyroglutamic acid (ERT). Results showed that PSP decreases exponentially with increasing SAC by MgSt. The composition of material stuck to punch face was also explored to better understand the onset of punch sticking and the impact of possible MgSt-effected punch conditioning event.

Experimental investigation on the change of pull-off force between bulk particulate material and an elastic polymeric filter fiber

HYPOTHESIS

Adhesion between particles and a filter fiber is an important process of the filtration as it dictates the process of separation and in the following the detachment process of particles during filter regeneration. In addition to the shear stress that a new polymeric stretchable filter fiber implements into the particulate structure, the elongation of the substrate (fiber) is also expected to cause a structural change in the surface of the polymer. Thus, the changed contact area and surface energy could affect the adhesion force between particles and fibers.

EXPERIMENTS

Systematic measurements of adhesion forces between a single particle and the stretchable substrate were performed using Atomic Force Microscope (AFM). The substrate surface characteristics (roughness) was changed directly beneath the modified measurement head using piezo-motors to achieve stepless elongation state. Polystyrene particles and particles made of Spheriglass were applied.

FINDINGS

In the experiments, a reduced adhesion force between the particles and the filter fiber was found for a new high range of substrate roughness and peak-to-peak distance, in which the Rabinovich model has not been used before [1]. Further, the influence of high and low energy surface particulate material was evaluated to understand the detachment process in the new real adaptive filter and in DEM-simulation.

Efficacy of Nanosilica Coatings in Calcium Looping Reactors

Nanosilica coatings are considered a simple physical treatment to alleviate the effect of cohesion on powder flowability. In limestone powders, these coatings buffer the rise in cohesion at high temperatures. Here, we investigate the role of particle size in the efficiency (and resilience) of these layers. To this end, this work examines a series of four limestone powders with very sharp particle size distributions: average particle size ranged from 15 to 60 μm. All the samples were treated with nanosilica at different concentrations from 0 to 0.82 wt %. Powders were subjected to short- and long-term storage conditions in calcium looping based systems: temperatures that vary from 25 to 500 °C and moderate consolidations (up to 2 kPa). Experiments monitored powder cohesion and its ability to flow by tracking the tensile strength of different samples while fluidized freely. Fluidization profiles were also used to infer variation in packings and the internal friction of the powder bed. Interestingly, for particle sizes below 50 μm, the nanosilica treatment mitigated cohesion significantly-the more nanosilica content, the better the flowability performance. However, at high temperatures, the efficiency of nanosilica coatings declined in 60 μm samples. Scanning electron microscopy images confirmed that only 60 μm samples presented surfaces barely coated after the experiments. In conclusion, nanosilica coatings on limestone are not stable beyond the 50 μm threshold. This is a critical finding for thermochemical systems based on the calcium looping process, since larger particles can still exhibit a significant degree of cohesion at high temperatures.

Particle Agglomeration and Properties of Pregelatinized Potato Starch Powder

Pregelatinized starches are used as thickeners in many instant food products. The unique properties of pregelatinized starches, such as their dispersibility in water and high viscosity, are generally desirable for instant food products. However, powdered starches cannot be easily dispersed in cold water due to clumping. The most reliable method to solve this problem is particle size enlargement by an agglomeration technique that causes a structural change in the starch. In this study, pregelatinized potato starch powder (PPSP) was agglomerated in a fluidized bed agglomerator, after which the physical, structural, and rheological properties of the PPSP agglomerated with different maltodextrin (MD) binder concentrations were investigated. The powder solubility and flowability (CI and HR) of all the agglomerated PPSPs were improved, and the particle size (D₅₀) tended to increase as the MD concentration increased, except for the control (0% MD) and the 40% MD. The changes in the particle size of the agglomerated PPSPs were consistent with the SEM image analysis. The magnitudes of the gel strength and viscoelastic moduli (G' and G″) of the agglomerated PPSPs with 10% MD were higher than those of the control due to the more stable structure formed by better intermolecular interaction in the starch and MD during the agglomeration process. Therefore, our results indicated that the fluidized bed agglomeration process and the MD addition as a binder solution greatly influence the physical, structural, and rheological properties of PPSP.

Recent developments in the computational simulation of dry powder inhalers

This article reviews recent developments in computational modeling of dry powder inhalers (DPIs). DPIs deliver drug formulations (sometimes blended with larger carrier particles) to a patient's lungs via inhalation. Inhaler design is complicated by the need for maximum aerosolization efficiency, which is favored by high levels of turbulence near the mouthpiece, with low extrathoracic depositional loss, which requires low turbulence levels near the mouth-throat region. In this article, we review the physical processes contributing to aerosolization and subsequent dispersion and deposition. We assess the performance characteristics of DPIs using existing simulation techniques and offer a perspective on how such simulations can be improved to capture the physical processes occurring over a wide range of length- and timescales more efficiently.

Electrostatic dust removal using adsorbed moisture-assisted charge induction for sustainable operation of solar panels

Dust accumulation on solar panels is a major challenge, as it blocks a large portion of sunlight. Solar panels are therefore cleaned regularly using large quantities of pure water. Consumption of water for cleaning, especially in deserts, poses a substantial sustainability challenge. Here, we present a waterless approach for dust removal from solar panels using electrostatic induction. We find that dust particles, despite primarily consisting of insulating silica, can be electrostatically repelled from electrodes due to charge induction assisted by adsorbed moisture. We experimentally determine dust particle charge by conducting Stokes experiments under an electrostatic field. By considering electrostatic, van der Waals, and gravitational forces, we define the threshold electric potential for particle removal. We also demonstrate dust removal over a broad range of relative humidity, making our approach widely applicable. Last, we develop a lab-scale prototype and demonstrate up to 95% recovery of lost power output using our approach.

Theoretical and Experimental Analysis of Surface Roughness and Adhesion Forces of MEMS Surfaces Using a Novel Method for Making a Compound Sputtering Target

Achieving a compound thin film with uniform thickness and high purity has always been a challenge in the applications concerning micro electro mechanical systems (MEMS). Controlling the adhesion force in micro/nanoscale is also critical. In the present study, a novel method for making a sputtering compound target is proposed for coating Ag–Au thin films with thicknesses of 120 and 500 nm on silicon substrates. The surface topography and adhesion forces of the samples were obtained using atomic force microscope (AFM). Rabinovich and Rumpf models were utilized to measure the adhesion force and compare the results with the obtained experimental values. It was found that the layer with a thickness of 500 nm has a lower adhesion force than the one with 120 nm thickness. The results further indicated that due to surface asperity radius, the adhesion achieved from the Rabinovich model was closer to the experimental values. This novel method for making a compound sputtering target has led to a lower adhesion force which can be useful for coating microgripper surfaces.

DLVO Interactions between Particles and Rough Surfaces: An Extended Surface Element Integration Method

The surface element integration (SEI) method is a computationally facile technique for calculating DLVO interactions between particles and surfaces. This method yields the exact total DLVO interaction between a particle and a flat surface; however, all surfaces have some degree roughness that profoundly affects the interaction. Previously, an ad hoc approximate method has been used to extend the SEI method to interactions between particles and surfaces with arbitrary morphology. Here we derive a more rigorous approximate method based on the fundamental scaling of DLVO interactions, which approaches the exact solution as the separation distance decreases regardless of the particle or surface morphology. We verify this method by comparison to the exact van der Waals energy when roughness is present on the particle and surface. The accuracy of this method at small separations makes it well-suited for the contexts of particle adhesion and deposition in which the length scale of interaction is on the order of angstroms and nanometers, respectively.

Relative importance of electrostatic and van der Waals forces in particle adhesion to rough conducting surfaces

It is commonly assumed that van der Waals forces dominate adhesion in dry systems and electrostatic forces are of second order importance and can be safely neglected. This is unambiguously the case for particles interacting with flat surfaces. However, all surfaces have some degree of roughness. Here we calculate the electrostatic and van der Waals contributions to adhesion for a polarizable particle contacting a rough conducting surface. For van der Waals forces, surface roughness can diminish the force by several orders of magnitude. In contrast, for electrostatic forces, surface roughness affects the force only slightly, and in some regimes it actually increases the force. Since van der Waals forces decrease far more strongly with surface roughness than electrostatic forces, surface roughness acts to increase the relative importance of electrostatic forces to adhesion. We find that for a particle contacting a rough conducting surface, electrostatic forces can be dominant for particle sizes as small as ∼1-10 μm.

Particle adhesion to rough surfaces

While particle adhesion to smooth surfaces is well understood, real surfaces are not perfectly smooth, and the effects of surface roughness on adhesion are not easily characterized. We develop a theory for the effects of surface roughness on the strength of particle adhesion due to van der Waals forces, in the Derjaguin-Muller-Toporov (DMT)-type adhesion regime. We first address a well-defined rough surface created by embedding spheres in a smooth substrate, which had been previously examined experimentally. We derive an analytic expression for the adhesive force of particles to this well-defined surface, with the key distinction from the previous work being the inclusion of interactions from surface asperities not in direct contact with the particle. We show that our theory is in good agreement with experimental results in the DMT regime. Within appropriate limits, we extend our theory to general rough surfaces and verify the theory by comparing to the exact numerical results. We show that the interactions from surface asperities not in direct contact with the particle are the dominant contribution to the adhesive force under some conditions, and our theory predicts the experimental and numerical adhesion forces very accurately.

Two-dimensional finite element analysis of elastic adhesive contact of a rough surface

Adhesive contact of a rigid flat surface with an elastic substrate having Weierstrass surface profile is numerically analyzed using the finite element method. In this work, we investigate the relationship between load and contact area spanning the limits of non-adhesive normal contact to adhesive contact for various substrate material properties, surface energy and roughness parameters. In the limit of non-adhesive normal contact, our results are consistent with published work. For the adhesive contact problem, we employ Lennard-Jones type local contact interaction model with numerical regularization to study the transition from partial to full contact including jump-to-contact instabilities as well as load-depth hysteresis. We have investigated evolution of bonded contact area and pull-off force for various surface roughness parameters, substrate material properties and surface energy. We have identified two non-dimensional parameters to adequately explain experimentally observed adhesion weakening and strengthening phenomena. A design chart of the relative pull-off force as function of non-dimensional parameters is also presented.

Depth-Sensing Indentation as a Micro- and Nanomechanical Approach to Characterisation of Mechanical Properties of Soft, Biological, and Biomimetic Materials

Classical methods of material testing become extremely complicated or impossible at micro-/nanoscale. At the same time, depth-sensing indentation (DSI) can be applied without much change at various length scales. However, interpretation of the DSI data needs to be done carefully, as length-scale dependent effects, such as adhesion, should be taken into account. This review paper is focused on different DSI approaches and factors that can lead to erroneous results, if conventional DSI methods are used for micro-/nanomechanical testing, or testing soft materials. We also review our recent advances in the development of a method that intrinsically takes adhesion effects in DSI into account: the Borodich-Galanov (BG) method, and its extended variant (eBG). The BG/eBG methods can be considered a framework made of the experimental part (DSI by means of spherical indenters), and the data processing part (data fitting based on the mathematical model of the experiment), with such distinctive features as intrinsic model-based account of adhesion, the ability to simultaneously estimate elastic and adhesive properties of materials, and non-destructive nature.

The Next Generation of Colloidal Probes: A Universal Approach for Soft and Ultra-Small Particles

The colloidal probe technique, which is based on the atomic force microscope, revolutionizes direct force measurements in many fields, such as interface science or biomechanics. It allows for the first time to determine interaction forces on the single particle or cell level. However, for many applications, important "blind spots" remain, namely, the possibility to probe interaction potentials for nanoparticles or complex colloids with a soft outer shell. Definitely, these are colloidal systems that are currently of major industrial importance and interest from theory. The here-presented novel approach allows for overcome the aforementioned limitations. Its applicability has been demonstrated for 300 nm sized carboxylate-modified latex particles as well as sub-micron core-shell particles with a soft poly-N-isopropylacrylamide hydrogel shell and a rigid silica core. For the latter, which until now cannot be studied by the colloidal probe technique, determined is the temperature dependency of electrosteric and adhesion forces has been determined on the single particle level.

Enhanced Aerosolization of High Potency Nanoaggregates of Voriconazole by Dry Powder Inhalation

Invasive pulmonary aspergillosis is a deadly fungal infection with a high mortality rate, particularly in patients having undergone transplant surgery. Voriconazole, a triazole antifungal pharmaceutical product, is considered as a first-line therapy for invasive pulmonary aspergillosis, and exhibits efficacy even for patients who have failed other antifungal drug therapies. The objective of this study is to develop high potency nanoaggregates of crystalline voriconazole composition for dry powder inhalation using the particle engineering process, thin film freezing. In this study, mannitol at low concentrations acted as a surface texture-modifying agent, and we evaluated the physicochemical and aerodynamic properties of the voriconazole formulations containing different amounts of mannitol. In vitro aerosol performance data demonstrated that powder formulations consisting of 90 to 97% (w/w) voriconazole were the optimum for inhalation with a fine particle fraction (% of delivered dose) as high as 73.6 ± 3.2% and mass median aerodynamic diameter of 3.03 ± 0.17 μm when delivered by a commercially available device. The thin film freezing process enabled phase-separated submicron crystalline mannitol to be oriented such as to modify the surface texture of the crystalline voriconazole nanoaggregates, thus enhancing their aerosolization. Addition of as low as 3% (w/w) mannitol significantly increased the fine particle fraction (% of metered dose) of voriconazole nanoaggregates when compared to compositions without mannitol (40.8% vs 24.6%, respectively). The aerosol performance of the voriconazole nanoaggregates with 5% (w/w) mannitol was maintained for 13 months at 25 °C/60% RH. Therefore, voriconazole nanoaggregates having low amounts of surface texture-modifying mannitol made by thin film freezing are a feasible local treatment option for invasive pulmonary aspergillosis with high aerosolization efficiency and drug loading for dry powder inhalation.

Simulation of 3D nanomanipulation for rough spherical elastic and viscoelastic particles in a liquid medium; experimentally determination of cell's roughness parameters and Hamaker constant's correction

Due to the softness and vulnerability of biological cells, in manipulation operations, it is not possible to insert excessive force to move these cells. Also, cells in their living environment face with many dynamic factors; therefore, in order to prevent their destruction and death, consideration the environmental conditions, the theoretical studies that underlie the laboratory research should be closer to the actual results. So, in this article by simultaneous consideration of cell's viscoelasticity and asperities on its surface, as well as the correction of the viscoelastic constant in the liquid medium, the effects of the number of asperities on the contact area between cell and substrate on the manipulation process are investigated and by considering different mediums effects, cell's roughness and developed Hamaker for viscoelastic state, more accurate results of simulations are obtained. On the other hand, atomic force microscopy is also a powerful and multifunctional imaging device that provides observation and manipulation of biological samples, including single-cells, in a liquid medium. Consequently, in this study, using this device, the topography of the benign breast cancer cell is carried out in a liquid medium in contact mode. To correct the viscoelastic Hamaker constant, results are obtained using the Gwyddion software for extracting the roughness radius and the particle's height distribution function. In addition, simulation of the 3D manipulation for elastic and viscoelastic spherical bioactive particles in both air and liquid mediums is done applying particle's roughness with elastic and viscoelastic Hamaker constants. Results indicate that in the liquid medium due to changes in the adhesion force as well as the presence of drag force and surface tension, the critical force is reduced compared to air medium, and the effect of particle's roughness on the critical force and time is related to the number of asperities on the contact surface. Also, results are in good agreement with results of applying the particle's folding coefficient in the manipulation. In the second phase of the manipulation, the change trend in the manipulation force varies in different operating conditions.

Surface Forces Apparatus Measurements of Interactions between Rough and Reactive Calcite Surfaces

nm-Range forces acting between calcite surfaces in water affect macroscopic properties of carbonate rocks and calcite-based granular materials and are significantly influenced by calcite surface recrystallization. We suggest that the repulsive mechanical effects related to nm-scale surface recrystallization of calcite in water could be partially responsible for the observed decrease of cohesion in calcitic rocks saturated with water. Using the surface forces apparatus, we simultaneously followed the calcite reactivity and measured the forces in water in two surface configurations: between two rough calcite surfaces (CC) and between rough calcite and a smooth mica surface (CM). We used nm-scale rough, polycrystalline calcite films prepared by atomic layer deposition. We measured only repulsive forces in CC in CaCO₃-saturated water, which was related to roughness and possibly to repulsive hydration effects. Adhesive or repulsive forces were measured in CM in CaCO₃-saturated water depending on calcite roughness, and the adhesion was likely enhanced by electrostatic effects. The pull-off adhesive force in CM became stronger with time, and this increase was correlated with a decrease of roughness at contacts, the parameter which could be estimated from the measured force-distance curves. That suggested a progressive increase of real contact areas between the surfaces, caused by gradual pressure-driven deformation of calcite surface asperities during repeated loading-unloading cycles. Reactivity of calcite was affected by mass transport across nm- to μm-thick gaps between the surfaces. Major roughening was observed only for the smoothest calcite films, where gaps between two opposing surfaces were nm-thick over μm-sized areas and led to force of crystallization that could overcome confining pressures of the order of MPa. Any substantial roughening of calcite caused a significant increase of the repulsive mechanical force contribution.

Non-contact AFM measurement of the Hamaker constants of solids: Calibrating cantilever geometries

HYPOTHESIS

Surface effects arising from roughness and deformation can negatively affect the results of AFM contact experiments. Using the non-contact portion of an AFM deflection curve is therefore desirable for estimating the Hamaker constant, A, of a solid material. A previously validated non-contact quasi-dynamic method for estimating A is revisited, in which the cantilever tip is now always represented by an "effective sphere". In addition to simplifying this previous method, accurate estimates of A can still be obtained even though precise knowledge of the nanoscale geometric features of the cantilever tip are no longer required.

EXPERIMENTS

The tip's "effective" radius of curvature, R_eff, is determined from a "calibration" step, in which the tip's deflection at first contact with the surface is measured for a substrate with a known Hamaker constant. After R_eff is known for a given tip, estimates of A for other surfaces of interest are then determined.

FINDINGS

An experimental study was conducted to validate the new method and the obtained results are in good agreement with predictions from the Lifshitz approximation, when available. Since R_eff accounts for all geometric uncertainties of the tip through a single fitted parameter, no visual fitting of the tip shape was required.

Links between nanoscale and macroscale surface properties of natural root mucilage studied by atomic force microscopy and contact angle

Soil water repellency originating from organic coatings plays a crucial role for soil hydraulics and plant water uptake. Focussing on hydrophobicity in the rhizosphere induced by root-mucilage, this study aims to explore the link between macroscopic wettability and nano-microscopic surface properties. The existing knowledge of the nanostructures of organic soil compounds and its effect on wettability is limited by the lack of a method capable to assess the natural spatial heterogeneity of physical and chemical properties. In this contribution, this task is tackled by a geostatistical approach via variogram analysis of topography and adhesion force data acquired by atomic force microscopy and macroscopic sessile drop measurements on dried films of mucilage. The results are discussed following the wetting models given by Wenzel and Cassie-Baxter. Undiluted mucilage formed homogeneous films on the substrate with contact angles >90°. For diluted samples contact angles were smaller and incomplete mucilage surface coverage with hole-like structures frequently exhibited increased adhesion forces. Break-free distances of force curves indicated enhanced capillary forces due to adsorbed water films at atmospheric RH (35 ± 2%) that promote wettability. Variogram analysis enabled a description of complex surface structures exceeding the capability of comparative visual inspection.

Polymer-Lipid Microparticles for Pulmonary Delivery

Toward engineering approaches that are designed to optimize the particle size, morphology, and mucoadhesion behavior of the particulate component of inhaler formulations, this paper presents the preparation, physicochemical characterization, and preliminary in vitro evaluation of multicomponent polymer-lipid systems that are based on "spray-drying engineered" α-lactose monohydrate microparticles. The formulations combine an active (budesonide) with a lung surfactant (dipalmitoylphosphatidylcholine) and with materials that are known for their desirable effects on morphology (polyvinyl alcohol), aerosolization (l-leucine), and mucoadhesion (chitosan). The effect of the composition of formulations on the morphology, distribution, and in vitro mucoadhesion profiles is presented along with "Calu-3 cell monolayers" data that indicate good cytocompatibility and also with simulated-lung-fluid data that are consistent with the therapeutically useful release of budesonide.

Understanding the compaction behaviour of low-substituted HPC: macro, micro, and nano-metric evaluations

The fast development in materials science has resulted in the emergence of new pharmaceutical materials with superior physical and mechanical properties. Low-substituted hydroxypropyl cellulose is an ether derivative of cellulose and is praised for its multi-functionality as a binder, disintegrant, film coating agent and as a suitable material for medical dressings. Nevertheless, very little is known about the compaction behaviour of this polymer. The aim of the current study was to evaluate the compaction and disintegration behaviour of four grades of L-HPC namely; LH32, LH21, LH11, and LHB1. The macrometric properties of the four powders were studied and the compaction behaviour was evaluated using the out-of-die method. LH11 and LH22 showed poor flow properties as the powders were dominated by fibrous particles with high aspect ratios, which reduced the powder flow. LH32 showed a weak compressibility profile and demonstrated a large elastic region, making it harder for this polymer to deform plastically. These findings are supported by AFM which revealed the high roughness of LH32 powder (100.09 ± 18.84 nm), resulting in small area of contact, but promoting mechanical interlocking. On the contrary, LH21 and LH11 powders had smooth surfaces which enabled larger contact area and higher adhesion forces of 21.01 ± 11.35 nN and 9.50 ± 5.78 nN, respectively. This promoted bond formation during compression as LH21 and LH11 powders had low strength yield.

Bomb swab: Can trace explosive particle sampling and detection be improved?

The marked increase in international terror in recent years requires the development of highly efficient methods to detect trace amounts of explosives at airports, border crossings and check points. The preferred analytical method worldwide is the ion mobility spectrometry (IMS) that is capable of detecting most explosives at the nano-gram level. Sample collection for the IMS analysis is based on swabbing of a passenger's belongings to collect possible explosive residues. The present study examines a wide range of issues related to swab-based particle collection and analysis, in the hope of gaining deeper understanding into this technique that will serve to improve the detection process. The adhesion of explosive particles to three typical materials, plastic, metal and glass, were measured using atomic force microscopy (AFM). We found that a strong contribution of capillary forces to adhesion on glass and metal surfaces renders these substrates more promising materials upon which to find and collect explosive residues. The adhesion of explosives to different swipe materials was also examined. Here we found that Muslin, Nomex^® and polyamide membrane surfaces are the most promising materials for use as swipes. Subsequently, the efficiency of multiple swipe use - for collecting explosive residues from a glass surface using Muslin, Nomex^® and Teflon™ swipes - was examined. The study suggests that swipes used in about 5-10 "sampling and analysis cycles" have higher efficiency as compared to new unused swipes. The reason for this behavior was found to be related to the increased roughness of the swipe surface following a few swab measurements. Lastly, GC-MS analysis was employed to examine the nature of contaminants collected by the three types of swipe. The relative amounts of different contaminants are reported. The existence and interference of these contaminants have to be considered in relation to the detection efficiency of the various explosives by the IMS.

Vitamin B12 Grafted Layer-by-Layer Liposomes Bearing HBsAg Facilitate Oral Immunization: Effect of Modulated Biomechanical Properties

Adhesion forces of nanoparticulate materials toward biological membrane are crucial for designing a delivery system for therapeutic molecules and vaccines. The present study aims to investigate the impact of surface roughness of the nanoparticulate system in oral delivery of antigen and its targeting to toward intestinal antigen presenting cells. To evaluate this hypothesis, layer-by-layer coated liposomes (LBL-Lipo) were fabricated using sodium alginate and Vitamin B12 conjugated Chitosan (VitB12-Chi) as anionic and cationic polyelectrolyte, respectively. Change in surface roughness was observed on changes in pH from gastric to intestinal conditions attributed to increase and decrease in charge density on VitB12-Chi. Surface roughness was measured in terms of root-mean-square measured by topographical analysis using atomic force microscopy. LBL-Lipo were further characterized for their size, zeta potential, and release behavior to evaluate the potential for oral vaccine delivery. In vitro cell uptake in macrophage cells (J-744) shows about 2- and 3.1-fold increased uptake of rough LBL-Lipo over smooth LBL-Lipo at 37 °C (endocytosis) and 4 °C (endocytosis inhibition) indicating improved biological interaction. Further in vivo immunization study revealed that prototype formulations were able to produce 4.8- and 3.3-fold higher IgG and IgA levels in serum and feces, respectively, in comparison to smooth LBL-Lipo.

Influence of Nanoscale Surface Roughness on Colloidal Force Measurements

Forces between colloidal particles determine the performances of many industrial processes and products. Colloidal force measurements conducted between a colloidal particle AFM probe and particles immobilized on a flat substrate are valuable in selecting appropriate surfactants for colloidal stabilization. One of the features of inorganic fillers and extenders is the prevalence of rough surfaces-even the polymer latex particles, often used as model colloidal systems including the current study, have rough surfaces albeit at a much smaller scale. Surface roughness is frequently cited as the reason for disparity between experimental observations and theoretical treatment but seldom verified by direct evidence. This work reports the effect of nanoscale surface roughness on colloidal force measurements carried out in the presence of surfactants. We applied a heating method to reduce the mean surface roughness of commercial latex particles from 30 to 1 nm. We conducted force measurements using the two types of particles at various salt and surfactant concentrations. The surfactants used were pentaethylene glycol monododecyl ether, Pluronic F108, and a styrene/acrylic copolymer, Joncryl 60. In the absence of the surfactant, nanometer surface roughness affects colloidal forces only in high salt conditions when the Debye length becomes smaller than the surface roughness. The adhesion is stronger between colloids with higher surface roughness and requires a higher surfactant concentration to be eliminated. The effect of surface roughness on colloidal forces was also investigated as a function of the adsorbed surfactant layer structure characterized by AFM indentation and dynamic light scattering. We found that when the layer thickness exceeds the surface roughness, the colloidal adhesion is less influenced by surfactant concentration variation. This study demonstrates that surface roughness at the nanoscale can influence colloidal forces significantly and should be taken into account in colloidal dispersion formulations.

Multiscaling Approach for Non-Destructive Adhesion Studies of Metal/Polymer Composites

The adhesion of polyamide 6 (PA6) and polyethylene (PE) toward an aluminum alloy (Al-A) and a dual phase steel (DPS) is studied by contact angle (CA) measurements and atomic force microscopy (AFM). With the combination of the two methods the adhesion properties on a macro- and (sub)microscopic scale can be determined in a nondestructive way. The work of adhesion per area (Wad) of the studied metal/polymer hybrids qualitatively scales the same on both length scales, that is, Al-A/PA6 > DPS/PA6 > Al-A/PE, DPS/PE. The polymer dominates the adhesion. The lower adhesion for PE toward the metal surfaces is explained by dominating van der Waals attraction forces, whereas adhesion for PA6 can also be attributed to attractive polar forces such as hydrogen bonding. For metal/PA6, Wad on a macro- and microscopic length scale is similar. For metal/PE, a discrepancy is measured with lower adhesion values on the microscopic scale than on the macroscopic scale.

Dynamic modeling and simulation of rough cylindrical micro/nanoparticle manipulation with atomic force microscopy

In this paper, the process of pushing rough cylindrical micro/nanoparticles on a surface with an atomic force microscope (AFM) probe is investigated. For this purpose, the mechanics of contact involving adhesion are studied first. Then, a method is presented for estimating the real area of contact between a rough cylindrical particle (whose surface roughness is described by the Rumpf and Rabinovich models) and a smooth surface. A dynamic model is then obtained for the pushing of rough cylindrical particles on a surface with an AFM probe. Afterwards, the process is simulated for different particle sizes and various roughness dimensions. Finally, by reducing the length of the cylindrical particle, the simulation condition is brought closer to the manipulation condition of a smooth spherical particle on a rough substrate, and the simulation results of the two cases are compared. Based on the simulation results, the critical force and time of manipulation diminish for rough particles relative to smooth ones. Reduction in the aspect ratio at a constant cross-section radius and the radius of asperities (height of asperities based on the Rabinovich model) results in an increase in critical force and time of manipulation.