Smart Polymer Surfaces: Concepts and Applications in Biosciences

Temperature-Responsive Polymer Brush Coatings for Advanced Biomedical Applications

Modern biomedical technologies predict the application of materials and devices that not only can comply effectively with specific requirements, but also enable remote control of their functions. One of the most prospective materials for these advanced biomedical applications are materials based on temperature-responsive polymer brush coatings (TRPBCs). In this review, methods for the fabrication and characterization of TRPBCs are summarized, and possibilities for their application, as well as the advantages and disadvantages of the TRPBCs, are presented in detail. Special attention is paid to the mechanisms of thermo-responsibility of the TRPBCs. Applications of TRPBCs for temperature-switchable bacteria killing, temperature-controlled protein adsorption, cell culture, and temperature-controlled adhesion/detachment of cells and tissues are considered. The specific criteria required for the desired biomedical applications of TRPBCs are presented and discussed.

Stimulus-Responsive Polyelectrolyte Surfaces: Switching Surface Properties from Polycationic/Antimicrobial to Polyzwitterionic/Protein-Repellent

Surfaces coated with polyzwitterions are most well-known for their ability to resist protein adsorption. In this article, a surface-attached hydrophobically modified poly(carboxybetaine) is presented. When protonated by changes of the pH of the surrounding medium, this protein-repellent polyzwitterion switches to a polycationic state in which it is antimicrobially active and protein-adhesive. The pH range in which these two states exist are recorded by zeta potential measurements. Adsorption studies at different pH values (monitored by surface plasmon resonance spectroscopy) confirm that the adhesion of protein is pH dependent and reversible, that is, protein can be released upon a pH change from pH 3 to pH 7.4. At physiological pH, the poly(carboxyzwitterion) is antimicrobially active, presumably because it becomes protonated by bacterial metabolites during the antimicrobial activity assay. Stability studies confirm that the here presented material is storage-stable, yet hydrolyses after longer incubation in aqueous media.

Molecular Design of Zwitterionic Polymer Interfaces: Searching for the Difference

The widespread occurrence of zwitterionic compounds in nature has incited their frequent use in designing biomimetic materials. Therefore, zwitterionic polymers are a thriving field. A particular interest for this particular polymer class has currently focused on their use in establishing neutral, low-fouling surfaces. After highlighting strategies to prepare model zwitterionic surfaces as well as those that are more suitable for practical purposes relying strongly on radical polymerization methods, we present recent efforts to diversify the structure of the hitherto quite limited variety of zwitterionic monomers and of the derived polymers. We identify key structural variables, consider their influence on essential properties such as overall hydrophilicity and long-term stability, and discuss promising targets for the synthesis of new variants.

One-step surface grafting of organic nanoparticles: in situ deposition of antimicrobial agents vanillin and chitosan on polyethylene packaging films

Natural organic molecules, volatile vanillin and non-volatile chitosan, were deposited from solution onto a polyethylene surface by the ultrasonic method and demonstrate specific antimicrobial activity.

Responsive inverse opal hydrogels for the sensing of macromolecules

Dual responsive inverse opal hydrogels were designed as autonomous sensor systems for (bio)macromolecules, exploiting the analyte-induced modulation of the opal's structural color. The systems that are based on oligo(ethylene glycol) macromonomers additionally incorporate comonomers with various recognition units. They combine a coil-to-globule collapse transition of the LCST type with sensitivity of the transition temperature toward molecular recognition processes. This enables the specific detection of macromolecular analytes, such as glycopolymers and proteins, by simple optical methods. While the inverse opal structure assists the effective diffusion even of large analytes into the photonic crystal, the stimulus responsiveness gives rise to strong shifts of the optical Bragg peak of more than 100 nm upon analyte binding at a given temperature. The systems' design provides a versatile platform for the development of easy-to-use, fast, and low-cost sensors for pathogens.

Preparation and characterization of light-switchable polymer networks attached to solid substrates

Surface-attached polymer networks that carry light-responsive nitrospiropyran groups in a hydrophilic PDMAA matrix were prepared on planar silicon and glass surfaces and were characterized with respect to their switching behavior under the influence of an external light trigger. Functional polymers bearing light-responsive units as well as photo-cross-linkable benzophenone groups were first synthesized using free radical copolymerization. The number of spiropyran groups in the copolymer was controlled by adjusting the concentration of the respective monomer in the copolymerization feed. The polymer films were prepared by spin-coating the functional polymers from solution and by ultraviolet light (UV)-induced cross-linking utilizing benzophenone photochemistry. On substrates with immobilized benzophenone groups, the complete polymer network is linked to the surface. The dry thickness of the films can be controlled over a wide range from a few nanometers up to more than 1 μm. The integration of such light-switchable organic moieties into a surface-attached polymer network allows one to increase the overall number of light-responsive groups per surface area by adjusting the amount of surface-attached polymer networks. The spiropyran's function in dry (solvent-free) and swollen polymer films can be reversibly switched by UV and visible irradiation. In addition, the switching in water is faster than in the dry state. Therefore, implementing light-responsive spiropyran functions in polymer films linked to solid surfaces could allow for switching of the chemical and optical surface properties in a fast and spatially controlled fashion.

Poly[tri(ethylene glycol) ethyl ether methacrylate]-coated surfaces for controlled fibroblasts culturing

Well-defined thermosensitive poly[tri(ethylene glycol) monoethyl ether methacrylate] (P(TEGMA-EE)) brushes were synthesized on a solid substrate by the surface-initiated atom transfer radical polymerization of TEGMA-EE. The polymerization reaction was initiated by 2-bromo-2-methylpropionate groups immobilized on the surface of the wafers. The changes in the surface composition, morphology, philicity, and thickness that occurred at each step of wafer functionalization confirmed that all surface modification procedures were successful. Both the successful modification of the surface and bonding of the P(TEGMA-EE) layer were confirmed by X-ray photoelectron spectroscopy (XPS) measurements. The thickness of the obtained P(TEGMA-EE) layers increased with increasing polymerization time. The increase of environmental temperature above the cloud point temperature of P(TEGMA-EE) caused the changes of surface philicity. A simultaneous decrease in the polymer layer thickness confirmed the thermosensitive properties of these P(TEGMA-EE) layers. The thermosensitive polymer surfaces obtained were evaluated for the growth and harvesting of human fibroblasts (basic skin cells). At 37 °C, seeded cells adhered to and spread well onto the P(TEGMA-EE)-coated surfaces. A confluent cell sheet was formed within 24 h of cell culture. Lowering the temperature to an optimal value of 17.5 °C (below the cloud point temperature of the polymer, TCP, in cell culture medium) led to the separation of the fibroblast sheet from the polymer layer. These promising results indicate that the surfaces produced may successfully be used as substrate for engineering of skin tissue, especially for delivering cell sheets in the treatment of burns and slow-healing wounds.

Precise control of cell adhesion by combination of surface chemistry and soft lithography

The adhesion of cells on an extracellular matrix (ECM) (in vivo) or the surfaces of materials (in vitro) is a prerequisite for most cells to survive. The rapid growth of nano/microfabrication and biomaterial technologies has provided new materials with excellent surfaces with specific, desirable biological interactions with their surroundings. On one hand, the chemical and physical properties of material surfaces exert an extensive influence on cell adhesion, proliferation, migration, and differentiation. On the other hand, material surfaces are useful for fundamental cell biology research and tissue engineering. In this Review, an overview will be given of the chemical and physical properties of newly developed material surfaces and their biological effects, as well as soft lithographic techniques and their applications in cell biology research. Recent advances in the manipulation of cell adhesion by the combination of surface chemistry and soft lithography will also be highlighted.

Aqueous-based initiator attachment and ATRP grafting of polymer brushes from poly(methyl methacrylate) substrates

Many polymers, such as PMMA, are very susceptible to swelling or dissolution by organic solvents. Growing covalently attached polymer brushes from these surfaces by atom-transfer radical polymerization (ATRP) is challenging because of the typical requirement of organic solvent for initiator immobilization. We report an unprecedented, aqueous-based route to graft poly(N-isopropylacrylamide), PNIPAAm, from poly(methyl methacrylate), PMMA, surfaces by ATRP, wherein the underlying PMMA is unaffected. Successful attachment of the ATRP initiator, N-hydroxysuccinimidyl-2-bromo-2-methylpropionate, on amine-bearing PMMA surfaces was confirmed by XPS. From this surface-immobilized initiator, thermoresponsive PNIPAAm brushes were grown by aqueous ATRP to yield optically transparent PNIPAAm-grafted PMMA surfaces. This procedure is valuable, as it can be applied for the aqueous-based covalent attachment of ATRP initiator on any amine-functionalized surface, with subsequent polymerization of a variety of monomers.