Identification and monitoring of thiabendazole transformation products in water during Fenton degradation by LC-QTOF-MS

Magnetic Fe-doped silicon carbide induced microwave activated persulfate for decabromodiphenyl ether removal: Mechanism and unique degradation pathway

In this work, the magnetic nanocomposite Fe@SiC was prepared by a hydrothermal method and determined by SEM, XRD, XPS, FTIR and VNA. Fe3O4 particles were loaded onto SiC with great success, and the synthesized composites had favorable microwave absorption properties. Fe@SiC was used to activate persulfate in a microwave field for the degradation of BDE209 in soil. Specifically, the synergistic interaction between microwaves and Fe@SiC showed excellent catalytic performance in activating PS to degrade BDE209 (90.1% BDE209 degradation in 15 min). The presence of •OH, O2•- and 1O2 was demonstrated based on quench trapping and EPR experiments. LC‒MS was applied to determine the intermediates and propose the possible degradation pathway for BDE209 in the MW/Fe@SiC/PS system, and it was found that BDE209 produced almost no lower brominated diphenyl ethers. Therefore, the toxicity of BDE209 was found to be reduced using toxicity assessment software. Overall, this work provides an effective approach for the degradation of BDE209 in environmental remediation.

Combining LAESI Imaging and Tissue Spray Ionization Mass Spectrometry To Unveil Pesticides Contaminants in Fruits

There is an increasing need for developing a strategy to analyze the penetration of pesticides in cultures during postharvest control with minimal or no sample preparation. This study explores the combined use of laser ablation electrospray ionization mass spectrometry imaging (LAESI imaging) and tissue spray ionization mass spectrometry (TSI-MS) to investigate the penetration of thiabendazole (TBZ) in fruits, simulating a postharvest procedure. Slices of guava and apple were prepared, and an infrared laser beam was used, resulting in the ablation of TBZ directly ionized by electrospray and analyzed by mass spectrometry. The experiments were conducted for 5 days of fruit storage after TBZ administration to simulate a postharvest treatment. During postharvest treatment, TBZ is applied directly to the fruit peel after harvesting. Consequently, TBZ residues may remain on the peel if the consumer does not wash the fruit properly before its consumption. To evaluate the effectiveness of household washing procedures, TSI-MS was employed as a rapid and straightforward technique to monitor the remaining amount of TBZ in guava and apple peels following fruit washing. This study highlights the advantages of LAESI imaging for evaluating TBZ penetration in fruits. Moreover, the powerful capabilities of TSI-MS are demonstrated in monitoring and estimating TBZ residues after pesticide application, enabling the comprehensive unveiling of pesticide contaminants in fruits.

Thiabendazole degradation by photo-NaOCl/Fe and photo-Fenton like processes, using copper slag as an iron catalyst, in spiked synthetic and real secondary wastewater treatment plant effluents

Thiabendazole degradation (TBZ_D) in diferent types of water matrices was assessed by applying two Advanced Oxidation Processes, both using simulated solar light (SSL), copper slag (CS) as an iron based catalyst, and separately H₂O₂ or NaOCl as oxidants. First, optimum conditions for TBZ_D were evaluated in distilled water, TBZ_D = 90% at 60 min for CS-H₂O₂-SSL, and 92% of TBZ_D in a twelfth of the time by the system CS-NaOCl-SSL; minimum TBZ depletion variations were observed between the first and the fifth reuse test: 88 ± 2% for CS-H₂O₂-SSL (60 min) and 90 ± 1% for CS-NaOCl-SSL (5 min). Those conditions were tested using a synthetic (SE) and a real secondary effluent (RE) from a wastewater treatment plant. The CS-H₂O₂-SSL system achieved TBZ_D of 88 and 77% after 90 min for SE and RE, with kinetic constants of 0.024 and 0.016 min^-1, respectively, whereas photo-NaOCl/Fe showed values of 0.365 and 0.385 min^-1 for SE and RE, achieving a 94% TBZ_D removal in both types of water at 10 min. That might be related to the formation of Cl^· and HO^• during the photo-NaOCl/Fe process, highlighting that the CS-NaOCl-SSL is an attractive option that has great possibilities for scaling up by a better knowledge in real aqueous matrices.

Removal of Pharmaceuticals and Personal Care Products (PPCPs) by Free Radicals in Advanced Oxidation Processes

As emerging pollutants, pharmaceutical and personal care products (PPCPs) have received extensive attention due to their high detection frequency (with concentrations ranging from ng/L to μg/L) and potential risk to aqueous environments and human health. Advanced oxidation processes (AOPs) are effective techniques for the removal of PPCPs from water environments. In AOPs, different types of free radicals (HO·, SO₄·^-, O₂·^-, etc.) are generated to decompose PPCPs into non-toxic and small-molecule compounds, finally leading to the decomposition of PPCPs. This review systematically summarizes the features of various AOPs and the removal of PPCPs by different free radicals. The operation conditions and comprehensive performance of different types of free radicals are summarized, and the reaction mechanisms are further revealed. This review will provide a quick understanding of AOPs for later researchers.

Nutritional inter-dependencies and a carbazole-dioxygenase are key elements of a bacterial consortium relying on a Sphingomonas for the degradation of the fungicide thiabendazole

Thiabendazole (TBZ), is a persistent fungicide/anthelminthic and a serious environmental threat. We previously enriched a TBZ-degrading bacterial consortium and provided first evidence for a Sphingomonas involvement in TBZ transformation. Here, using a multi-omic approach combined with DNA-stable isotope probing (SIP) we verified the key degrading role of Sphingomonas and identify potential microbial interactions governing consortium functioning. SIP and amplicon sequencing analysis of the heavy and light DNA fraction of cultures grown on ¹³ C-labelled versus ¹² C-TBZ showed that 66% of the ¹³ C-labelled TBZ was assimilated by Sphingomonas. Metagenomic analysis retrieved 18 metagenome-assembled genomes with the dominant belonging to Sphingomonas, Sinobacteriaceae, Bradyrhizobium, Filimonas and Hydrogenophaga. Meta-transcriptomics/-proteomics and non-target mass spectrometry suggested TBZ transformation by Sphingomonas via initial cleavage by a carbazole dioxygenase (car) to thiazole-4-carboxamidine (terminal compound) and catechol or a cleaved benzyl ring derivative, further transformed through an ortho-cleavage (cat) pathway. Microbial co-occurrence and gene expression networks suggested strong interactions between Sphingomonas and a Hydrogenophaga. The latter activated its cobalamin biosynthetic pathway and Sphingomonas its cobalamin salvage pathway to satisfy its B12 auxotrophy. Our findings indicate microbial interactions aligning with the 'black queen hypothesis' where Sphingomonas (detoxifier, B12 recipient) and Hydrogenophaga (B12 producer, enjoying detoxification) act as both helpers and beneficiaries.

A Systematic Review of Photolysis and Hydrolysis Degradation Modes, Degradation Mechanisms, and Identification Methods of Pesticides

The degradation modes and characteristics of different pesticides were introduced. In addition, this paper also describes the degradation mechanism of different pesticides, classifies, and summarizes the methods of degradation products identification. For the sake of human life health and better biological environment, we should have a familiar knowledge of the natural degradation of pesticides and understand the photo-hydrolysis and its influencing factors (temperature, pH, light, etc.). Through the degradation mechanism and influencing factors, the degradation time could be accelerated and it also provides a theoretical basis and basic support for the treatment of pesticide residues in the future.

Biotreatment and bacterial succession in an upflow immobilized cell bioreactor fed with fludioxonil wastewater

The large quantities and the persistent nature of fungicide wastewaters have increased the efforts towards a sustainable technological solution. In this context, fludioxonil-contaminated wastewater was treated in an upflow immobilized cell bioreactor, resulting in chemical oxygen demand (COD) removal efficiency even higher than 80%, whereas the electrical conductivity (EC) of the effluent was gradually increased. Organic-F was mineralized by 94.0 ± 5.2%, which was in accordance with the high fludioxonil removal efficiency (95.4 ± 4.0%). In addition, effluent total Kjeldahl nitrogen (TKN) concentration reduced significantly during bioprocessing. A strong relationship among COD removal, TKN/total nitrogen removal, and effluent EC increase (p < 0.01) was identified. Despite the adequate aeration provided, effluent nitrite and nitrate concentrations were negligible. Illumina sequencing revealed a reduction in the relative abundances of Betaproteobacteria, Chloroflexi, Planctomycetes, and Firmicutes and an increase in the proportion of Alphaproteobacteria and Actinobacteria. A shift in bacterial communities occurred during fludioxonil treatment, resulting in the significant increase of the relative abundances of Empedobacter, Sphingopyxis, and Rhodopseudomonas (from 0.67 ± 0.13% at the start-up to 34.34 ± 1.60% at the end of biotreatment). In conclusion, the immobilized cell bioreactor permitted the proliferation of specialized activated sludge microbiota with an active role in the depuration of postharvest fungicides.

Degradation of a Novel Pesticide Antiviral Agent Vanisulfane in Aqueous Solution: Kinetics, Identification of Photolysis Products, and Pathway

Hydrolysis degradation kinetics of vanisulfane in water was investigated in detail under exogenous substances conditions. The experimental results indicated that the degradation rate of vanisulfane in aqueous solution increases with the increase of concentration of Cu²⁺. The degradation of vanisulfane did not change significantly in Ni²⁺, Zn²⁺, Pb²⁺, and Fe³⁺ aqueous solutions. Surfactants have no significant effect on the degradation of vanisulfane, and the degradation rate of vanisulfane increases with increasing concentration of fulvic acid. In addition, the photolysis products were identified by ultra-high-performance liquid chromatography coupled with Orbitrap high-resolution mass spectrometry. Five photolysis products were identified, and the degradation reaction pathway and the mechanism of vanisulfane were proposed, which mainly involved cleavage of thioether, back into aldehyde, cleavage of ether bond, demethylation, and intramolecular dehydration processes. This research on vanisulfane can be helpful for its security evaluation and increased understanding of vanisulfane in water environments.

Total dissolved iron and hydrogen peroxide determination using the PhotoMetrixPRO application: A portable colorimetric analysis tool for controlling important conditions in the solar photo-Fenton process

The use of the solar photo-Fenton process for water treatment requires monitoring of the main conditions, especially the total dissolved iron concentration and the consumption of hydrogen peroxide. In this study, a new methodology using the PhotoMetrixPRO application was validated for rapid monitoring of total dissolved iron and hydrogen peroxide concentrations, and was tested in the solar photo-Fenton process. A comparison was made between the results obtained using a reference spectrophotometric method and the PhotoMetrixPRO application employing a portable device. Both methods were validated in terms of linearity, sensitivity, precision, robustness, and matrix effects. The degree of dispersion between the series of measurements obtained using UV-vis and portable device tool was low and was in compliance with the established Brazilian and ICH validation criteria. Additionally, PhotoMetrixPRO enabled the use of a smaller sample volume. The total volume generated of each sample is 1 mL, reducing 6 and 10 times the wastes produced in different validated methods. These results evidencing that the miniaturization can provide positive advantages in terms of simplicity, cost effectiveness, and less environmental impact. PhotoMetrixPRO offers significant advantages including rapid analysis, smaller sample volumes, and greater portability and accessibility.

Expanding the use of biobeds: Degradation and adsorption of pesticides contained in effluents from seed-coating, bulb disinfestation and fruit-packaging activities

Agro-food industries that use pesticides constitute significant point sources for the contamination of natural water resources. Despite that, little is known about the treatment of their pesticide-contaminated effluents. Biobeds could be a possible solution for the depuration of these effluents. In this context, we explored the degradation and adsorption of pesticides used in seed-coating (carboxin (CBX), metalaxyl-M (MET-M), fluxapyroxad (FLX), fludioxonil (FLD)), bulb-dipping (chlorothalonil (CHT), thiabendazole (TBZ), FLD) and fruit-packaging activities (FLD) in a biomixture, used as biobed packing material, and in soil. The degradation of pesticides was tested individually and in mixtures relevant to their industrial use, while FLD was also tested at different concentrations (10, 20, and 150 mg kg^-1) representing its use in the different industries. CBX, FLD, and CHT, when applied individually, and all other pesticides when applied in mixtures, degraded more rapidly in biomixture than in soil. In most cases pesticides application in mixtures retarded their degradation. This was more pronounced in soil than in biomixture, especially for MET-M and FLD. CHT had the most prominent inhibitory effect on the degradation of TBZ and FLD. FLD degradation showed a dose-dependent pattern (DT₅₀ 42.4 days at 10 mg kg^-1 and 107.6 days at 150 mg kg^-1). All pesticides showed higher adsorption affinity in the biomixture (K_f = 3.23-123.3 g mL^-1) compared to soil (K_f = 1.15-31.2 g mL^-1). We provide initial evidence for the potential of the tested biomixture to remove pesticides contained in effluents produced by different agro-industrial activities. Tests in full-scale biobeds packed with this biomixture will unravel their full depuration potential for the treatment of these agro-industrial effluents.

Determination of pesticide levels in wastewater from an agro-food industry: Target, suspect and transformation product analysis

Agriculture is considered as the main source of water contamination by pesticides. However, food packaging or processing industries are also recognised as relevant point sources of contamination by these compounds, not yet investigated in depth. The objective of this work has been to improve current knowledge about the presence and concentration of pesticides in the effluent of a food processing industry, as well as to investigate their main transformation products (TPs). An analytical strategy combining target and suspect analysis has been applied to provide an evaluation of the effluents. The methodology involves solid-phase extraction (SPE) of wastewater samples followed by (i) liquid chromatography quadrupole-linear ion trap tandem mass spectrometry (LC-QqLIT-MS/MS) for quantitative target analysis and (ii) liquid chromatography coupled to quadrupole-time-of-flight high resolution mass spectrometry (LC-QTOF-HRMS) to identify non-target pesticides and possible TPs. The results revealed the presence of 17 of the target pesticides analysed and 3 additional ones as a result of the suspect screening performed by HRMS. The TPs were investigated for the pesticides found at the highest concentrations: imazalil (7038-19802 ng/L), pyrimethanil (744-9591 ng/L) and thiabendazole (341-926 ng/L). Up to 14 TPs could be tentatively identified, demonstrating the relevance of this type of studies. These data provide a better understanding of the occurrence of pesticides and their TPs in agro-food industrial effluents.

SERS monitoring of the Fenton degradation reaction based on microfluidic droplets and alginate microparticles

Surface-enhanced Raman scattering (SERS) spectroscopy as a powerful tool has been used to explore different catalysis degradation reactions, whereas some drawbacks caused by ferric ions still exist in the current SERS monitoring of the Fenton reaction process. In this work, microfluidic droplet- and alginate microparticle-based methods were, respectively, applied to realize SERS monitoring of the Fenton degradation process in a relatively stable environment, which benefited from reduction of the loss of ferrous ions and the aggregation of the SERS substrate. As expected, the spectroscopic evidence at the molecular level directly revealed the degradation mechanism of rhodamine dyes, showing that the chemical bonds between xanthene and carboxybenzene broke continuously during the reaction. Afterward, the degradation mechanism determined by SERS was verified via mass spectrometry detection, which confirmed the validity of the SERS-based method. More broadly, the microfluidic droplet- and microparticle-based methods are potentially applicable for SERS monitoring of more Fenton degradation reactions.

Process design of high-concentration benzimidazole wastewater treatment based on the molecular structure of contaminants

Benzimidazole is an important intermediate in industry and it is usually difficult to be degraded by many treatment technologies. Looking for a highly effective, environment-friendly degradation process for benzimidazole wastewater is of great significance to reduce pollution. Based on the structure of contaminants, the micro-electrolysis (ME) coupled with the Fenton technique was chosen to degrade the industrial benzimidazole wastewater. Special feeding was applied to maintain the suitable hydrogen peroxide (H₂O₂) concentration to produce the hydroxyl radicals (•OH) as much as possible and protect •OH from being quenched by excess H₂O₂ according to the reaction mechanism. The results showed that this combined technique was highly efficient to decompose benzimidazole compounds. More chemical oxygen demand (COD) could be reduced when flow control was used, compared to the flow not being controlled. The COD removal rate could reach 85.2% at optimal parameters. Then the effluent of this process was combined with the existing biochemical system for further degradation. The studies of Ultraviolet Spectrophotometry, Fourier Transform Infrared Spectroscopy and Liquid Chromatography Mass Spectrometry showed that both 2-(a-Hydroxyethyl) benzimidazole and 2-Acetylbenzimidazole were decomposed to the isopropanolamine and aniline after the ME treatment; then the intermediates were oxidized into oxalic acid after the Fenton reaction.

Transformation products elucidation of forchlorfenuron in postharvest kiwifruit by time-of-flight mass spectrometry

Forchlorfenuron (1-(2-chloro-4-pyridyl)-3-phenylurea, FCF) is a plant growth regulator, being extensively used for increasing kiwifruit size. The toxicological properties of its may persist in their transformation products (TPs) or even higher toxicity than FCF. TPs elucidation of FCF in postharvest kiwifruit (Actinidia chinensis, Chinese gooseberry) by the liquid chromatography ionization hybrid ion trap and time-of-flight mass spectrometry (LC-ESI-IT-TOF/MS) in positive mode was the objective of the present study. Fifteen days after full bloom, kiwifruits were dipped for 5s with high dosage FCF solution (60 mg/L), so that sufficient peaks could be detected. The chemical structure of unknown TPs was analyzed in combination of functions of LCMS-IT-TOF, such as high-accurate MSⁿ, formula predictor, metabolite structural analysis software MetID Solution, profiling solution metabolomics software, and neutral loss, characteristic isotopic patterns of chlorine, the fragmentation pattern and retention time of standard substances, nitrogen rule, chemical components of kiwifruit. Total 17 TPs were detected via comparisons of their accurate MSⁿ data of commercial analytical standards and synthesized standards with high purity, such as 4-amino-2-chloropyridine, phenylurea, 2-hydroxy-FCF, 1-(2-chloro-6-((3, 4, 5-trihydroxy-6-(hydroxymethyl) tetrahydro-2H-pyran-2-yl) oxy) pyridin-4-yl)-3-phenylurea, 1, 3-bis (2-chloropyridin-4-yl) urea, 1,3-diphenylurea, 1-(2-chloropyridin-4-yl)urea, FCF-2-O-β-D-glucoside, and so on. The major transformation pathways of FCF in kiwifruit were biochemical and photochemical cleavage pathway. The experimental results indicate that LCMS-IT-TOF is powerful and effective tool for identification of FCF TPs.

Comparative study on sulfamethoxazole degradation by Fenton and Fe(ii)-activated persulfate process

Sulfamethoxazole can be effectively degraded by Fenton and Fe(ii)-activated persulfate. The concentration of oxidant has important effect on the degradation of sulfamethoxazole.

Integrated biodepuration of pesticide-contaminated wastewaters from the fruit-packaging industry using biobeds: Bioaugmentation, risk assessment and optimized management

Wastewaters from fruit-packaging plants contain high loads of toxic and persistent pesticides and should be treated on site. We evaluated the depuration performance of five pilot biobeds against those effluents. In addition we tested bioaugmentation with bacterial inocula as a strategy for optimization of their depuration capacity. Finally we determined the composition and functional dynamics of the microbial community via q-PCR. Practical issues were also addressed including the risk associated with the direct environmental disposal of biobed-treated effluents and decontamination methods for the spent packing material. Biobeds showed high depuration capacity (>99.5%) against all pesticides with bioaugmentation maximizing their depuration performance against the persistent fungicide thiabendazole (TBZ). This was followed by a significant increase in the abundance of bacteria, fungi and of catabolic genes of aromatic compounds catA and pcaH. Bioaugmentation was the most potent decontamination method for spent packing material with composting being an effective alternative. Risk assessment based on practical scenarios (pome and citrus fruit-packaging plants) and the depuration performance of the pilot biobeds showed that discharge of the treated effluents into an 0.1-ha disposal site did not entail an environmental risk, except for TBZ-containing effluents where a larger disposal area (0.2ha) or bioaugmentation alleviated the risk.

Cell-based assays in combination with ultra-high performance liquid chromatography-quadrupole time of flight tandem mass spectrometry for screening bioactive capilliposide C metabolites generated by rat intestinal microflora

Many plant-derived glycosides are used as medications. It is common that these glycosides show poor intestinal absorption but their metabolites generated by intestinal microflora demonstrate strong bioactivity. Hence, it is crucial to develop a method for the identification and characterization of the metabolites, and consequently reveal the pathway in which the glycosides are processed in gut. In this study, cell-based assays in combination with ultra-high performance liquid chromatography-quadrupole time of flight tandem mass spectrometry (UHPLC-QTOF-MS/MS) were developed for rapid discovery and evaluation of the metabolites of a glycoside compound, capilliposide C (LC-C). 92.7% of LC-C was biotransformed by rat intestinal microflora after 36-h incubation at 37°C. Human cancer cell lines HepG2, PC-3 and A549 was treated with metabolites pool, respectively, which was followed by cell viability assays and characterization of metabolites using UHPLC-QTOF-MS/MS. As a result, significant cytotoxicity was observed for the metabolites pool, from which six metabolites were identified. Based on the metabolites identified, deglycosylation and esterolysis were proposed as the major metabolic pathways of LC-C in rat intestinal microflora. In addition, M4, an esterolysis product of LC-C, was obtained and evaluated for its bioactivity in vitro. As a result, M4 exhibited a reduction in cell viability in HepG2 with an IC50 value of 17.46±1.55μg/mL.

Dissipation, metabolism and sorption of pesticides used in fruit-packaging plants: Towards an optimized depuration of their pesticide-contaminated agro-industrial effluents

Wastewaters from the fruit-packaging industry constitute a serious point source contamination with pesticides. In the absence of effective depuration methods, they are discharged in municipal wastewater treatment plants or spread to land. Modified biobeds could be an applicable solution for their treatment. We studied the dissipation of thiabendazole (TBZ), imazalil (IMZ), ortho-phenylphenol (OPP), diphenylamine (DPA) and ethoxyquin (EQ), used by the fruit-packaging industry, in anaerobically digested sewage sludge, liquid aerobic sewage sludge and in various organic substrates (biobeds packing materials) composed of soil, straw and spend mushroom substrate (SMS) in various volumetric ratios. Pesticide sorption was also determined. TBZ and IMZ showed higher persistence especially in the anaerobically digested sewage sludge (DT50=32.3-257.6d), in contrast to OPP and DPA which were rapidly dissipated especially in liquid aerobic sewage sludge (DT50=1.3-9.3d). EQ was rapidly oxidized mainly to quinone imine (QI) which did not persist and dimethyl ethoxyquinoline (EQNL, minor metabolite) which persisted for longer. Sterilization of liquid aerobic sewage sludge inhibited pesticide decay verifying the microbial nature of pesticide dissipation. Organic substrates rich in SMS showed the highest dissipation capacity with TBZ and IMZ DT50s of ca. 28 d compared to DT50s of >50 d in the other substrates. TBZ and IMZ showed the highest sorption affinity, whereas OPP and DPA were weakly sorbed. Our findings suggest that current disposal practices could not guarantee an efficient depuration of effluents from the fruit-packaging industry, whereas SMS-rich biobed organic substrates show efficient depuration of effluents from the fruit-packaging industry via accelerated dissipation even of recalcitrant fungicides.

Rapid Screening of Multiclass Syrup Adulterants in Honey by Ultrahigh-Performance Liquid Chromatography/Quadrupole Time of Flight Mass Spectrometry

Honey adulteration with sugar syrups is a widespread problem. Several types of syrups have been used in honey adulteration, and there is no available method that can simultaneously detect all of these adulterants. In this study, we generated a small-scale database containing the specific chromatographic and mass spectrometry information on sugar syrup markers and developed a simple, rapid, and effective ultrahigh-performance liquid chromatography/quadrupole time-of-flight mass spectrometry (UHPLC/Q-TOF-MS) method for the detection of adulterated honey. Corn syrup, high-fructose corn syrup, inverted syrup, and rice syrup were used as honey adulterants; polysaccharides, difructose anhydrides, and 2-acetylfuran-3-glucopyranoside were used as detection markers. The presence of 10% sugar syrup in honey could be easily detected in <30 min using the developed method. The results revealed that UHPLC/Q-TOF-MS was simple and rapid.

Degradation and monitoring of acetamiprid, thiabendazole and their transformation products in an agro-food industry effluent during solar photo-Fenton treatment in a raceway pond reactor

In this study, pesticides acetamiprid and thiabendazole and their transformation products (TPs), seven from each pesticide, were successfully monitored during solar photo-Fenton treatment in a real secondary effluent from an agro-food industry spiked with 100μgL(-1) of each pesticide. To this end, a highly sensitive procedure was developed, based on liquid chromatography (LC) coupled to hybrid quadrupole-linear ion trap mass spectrometry (QqLIT-MS). In addition, finding low-cost and operational technology for the application of AOPs would then facilitate their use on a commercial level. Simple and extensive photoreactors such as raceway pond reactors (RPRs) are therefore proposed as an alternative for the application of solar photo-Fenton. Results showed that high degradation could be achieved in a complex water matrix (>99% TBZ and 91% ACTM in 240min) using a 120-L RPR pilot plant as novel technology. The analyses indicated that after the treatment only three TPs from ACTM were still present in the effluent, while the others had been removed. The study showed that the goal of either just removing the parent compounds, or going one step further and removing all the TPs, can significantly change the treatment time, which would affect process costs.