Current trends in supercritical fluid chromatography

Fundamental investigation of impact of water and TFA additions in peptide sub/supercritical fluid separations

The retention of three peptides was studied under analytical and overloaded conditions at different concentrations of trifluoroacetic acid (TFA) and water added to the co-solvent methanol (MeOH). Four columns with different stationary phase properties, i.e., silica, diol, 2-ethylpyridine and cyanopropyl (CN) columns, were evaluated in this investigation. The overall aim was to get a deeper understanding on how column chemistry as well as water and TFA in the co-solvent affect the analytical and overloaded elution profiles using multivariate design of experiments and adsorption measurements of co-solvent components. Multivariate experimental design modeling indicated that water had on average around five times higher effect on the retention than the addition of TFA. The results also showed that the retention increases with the addition of TFA and water to the co-solvent on all columns except the CN column, on which the retention decreased. When examining the effect of adding water to the co-solvent, evidence of a hydrophilic interaction liquid chromatography (HILIC)-like retention mechanism was found on the three other columns with more polar stationary phases. However, on the CN column water acted as an additive, decreasing the retention due to competition with the peptide for available adsorption surface. Adsorption isotherm measurements of the polar solvent MeOH showed that MeOH adsorbs much weaker on the CN column than on the other columns. Addition of TFA and water to the co-solvent substantially sharpened the elution profiles under both overloaded and analytical conditions. Adding a small amount of TFA (from 0 % to 0.05 %) to the co-solvent substantially improved the peak shape of the elution profiles, while further addition (from 0.05 % to 0.15 %) had only a minor effect on the elution profile shape. The reduced retention on the CN column could not be explained by TFA adsorption, which was very weak on all studied columns (retention factor, 0.05-0.15). One could therefore speculate that the ion-pairing complex formed between the peptide and TFA in the mobile phase, reduce the retention due to its reduced polarity. On the other columns displaying HILIC-like properties, the TFA probably just decreased the pH of the mobile phase, thereby promoting the partitioning of the peptide into the water-rich layer. Finally, peak deformation due to diluent-eluent mismatch was observed under overloaded conditions. This was most severe in the cases where MeOH adsorption to the stationary phase was strong and the peptides were only mildly retained. Adding 1,4-dioxan to the diluent resolved this issue.

Economical and rapid enantioselective, diastereoselective and achiral separation of palonosetron hydrochloride and its impurities using supercritical fluid chromatography

Simultaneous separation of compounds with multiple chiral centers and highly similar structures presents significant challenges. This study developed a novel supercritical fluid chromatography (SFC) method with reduced organic solvent consumption and robust separation capabilities to address these challenges. The method was applied to simultaneously achieve enantioselective, diastereoselective, and achiral separation of palonosetron hydrochloride and its six impurities. The effects of the polysaccharide-based chiral stationary phase (CSP), modifier, additive, and column temperature on retention and separation were comprehensively evaluated. It was found that a combination of a polysaccharide-based CSP and a single modifier or a mixture of protonic modifiers could not achieve complete separation due to high structural similarity. However, an ADH column and a ternary solvent mixture containing acetonitrile (methanol: acetonitrile: diethylamine, 60:40:0.2, v/v/v) provided satisfying separation, particularly for the enantiomer and diastereomers of palonosetron. Using the optimized method, the enantioselective, diastereoselective, and achiral separation of palonosetron hydrochloride and its six impurities can be accomplished in 18 min under gradient elution. Thermodynamic results indicated that the separation process was entropy driven. A molecular docking study revealed that the separation was mainly achieved through the differences in hydrogen bond and π - π interactions between the analytes and CSP. This study lays the foundation for SFC analysis of palonosetron hydrochloride and provides a reference for the simultaneous SFC separation of the enantiomers, diastereoisomers and structurally similar compounds.

Modular Chip-Based nanoSFC-MS for Ultrafast Separations

This study presents the development of a miniaturized device for supercritical fluid chromatography coupled with mass spectrometry. The chip-based, modular nanoSFC approach utilizes a particle-packed nanobore column embedded between two monolithically structured glass chips. A microtee in the pre-column section ensures picoliter sample loads onto the column, while a microcross chip structure fluidically controls the column backpressure. The restrictive emitter and the minimal post-column volume of 16 nL prevent mobile phase decompression and analyte dilution, maintaining chromatographic integrity during transfer to the atmospheric pressure MS interface. This facilitates high-speed chiral separations in less than 80 s with high reproducibility.

An improved subtraction model applied in supercritical fluid chromatography to characterise polar stationary phases

Herein, an improved subtraction model was proposed to characterise the polar stationary phases in supercritical fluid chromatography (SFC). Fifteen stationary phases were selected, including two types of aromatic columns, Waters Torus and Viridis series columns, as well as silica and amino columns. Ethylbenzene and Torus 1-AA were defined as the reference solute and column, respectively. Identifying the interaction with the maximum contribution to retention in SFC separation and using it as the initial term is a key step in modelling. The dipole, or induced dipole interaction (θ'P), replaced the hydrophobic interaction (η'H) as the starting term. The improved model was expressed as logα=η'H+β'A+α'B+κ'C+θ'P+ε'E+σ'S, where the term ε'E indicated that anion exchange interaction was intentionally supplemented. A 7-step modelling process, including bidirectional fitting and residual analysis, was proposed. The obtained column parameters had reasonable physical significance, with the adjusted determination coefficient (R2adj) greater than 0.999 and the standard error (SE) less than 0.029. Methodological validation was further performed using the other four columns and 12 solutes that were not involved in the modelling. The result revealed good predictions of solutes' retention, as demonstrated by R2adj from 0.9923 to 0.9979 and SE from 0.0636 to 0.1088. This study indicated the feasibility of using the improved subtraction model to characterise polar stationary phases in SFC, with the most crucial being the determination of an initial term, followed by the addition of a new descriptor and the selection of an appropriate reference column. The study expanded the application scope of the subtraction model in SFC, which will help gain an in-depth understanding of the SFC separation mechanism.

Large-scale purification of a deprotected macrocyclic peptide by supercritical fluid chromatography (SFC) integrated with liquid chromatography in discovery chemistry

A macrocyclic peptide A was successfully purified in large quantities (∼30 g) in >95 % purity by an integrated two-step orthogonal purification process combining supercritical fluid chromatography (SFC) with medium-pressure reverse-phase liquid chromatography (MP-RPLC). MP-RPLC was used to fractionate the crude peptide A, remove unwanted trifluoroacetic acid (TFA) originating from the peptide A cleavage off the resin, and convert the peptide A into ammonium acetate salt form, prior to the final purification by SFC. A co-solvent of methanol/acetonitrile containing ammonium acetate and water in CO2 was developed on a Waters BEH 2-Ethylpyridine column. The developed SFC method was readily scaled up onto a 5 cm diameter column to process multi-gram quantities of the MP-RPLC fraction to reach > 95 % purity with a throughput/productivity of 0.96 g/h. The incorporation of SFC with MP-RPLC has been demonstrated to have a broader application in other large-scale polypeptide purifications.

Hyphenation of supercritical fluid chromatography and trapped ion mobility-mass spectrometry for quantitative lipidomics

BACKGROUND

Lipidomics studies require rapid separations with accurate and reliable quantification results to further elucidate the role of lipids in biological processes and their biological functions. Supercritical fluid chromatography (SFC), in particular, can provide this rapid and high-resolution separation. The combination with trapped ion mobility spectrometry (TIMS) has not yet been applied, although the post-ionization separation method in combination with liquid chromatography or imaging techniques has already proven itself in resolving isomeric and isobaric lipids and preventing false identifications. However, a multidimensional separation method should not only allow confident identification but also provide quantitative results to substantiate studies with absolute concentrations.

RESULTS

A SFC method was developed and the hyphenation of SFC and TIMS was further explored towards the separation of different isobaric overlaps. Furthermore, lipid identification was performed using mass spectrometry (MS) and parallel accumulation serial fragmentation (PASEF) MS/MS experiments in addition to retention time and collision cross section (CCS). Quantification was further investigated with short TIMS ramps and performed based on the ion mobility signal of lipids, since TIMS increases the sensitivity by noise filtering. The final method was, as an exemplary study, applied to investigate the function of different ceramide synthases (CerS) in the nematode and model organism Caenorhabditis elegans (C. elegans). Loss of three known CerS hyl-1, hyl-2 and lagr-1 demonstrated different influences on and alterations in the sphingolipidome.

SIGNIFICANCE

This method describes for the first time the combination of SFC and TIMS-MS/MS, which enables a fast and sensitive quantification of lipids. The results of the application to C. elegans samples prove the functionality of the method and support research on the metabolism of sphingolipids in nematodes.

Nitrophenols in the environment: An update on pretreatment and analysis techniques since 2017

Nitrophenols, a versatile intermediate, have been widely used in leather, medicine, chemical synthesis, and other fields. Because these components are widely applied, they can enter the environment through various routes, leading to many hazards and toxicities. There has been a recent surge in the development of simple, rapid, environmentally friendly, and effective techniques for determining these environmental pollutants. This review provides a comprehensive overview of the latest research progress on the pretreatment and analysis methods of nitrophenols since 2017, with a focus on environmental samples. Pretreatment methods include liquid-liquid extraction, solid-phase extraction, dispersive extraction, and microextraction methods. Analysis methods mainly include liquid chromatography-based methods, gas chromatography-based methods, supercritical fluid chromatography. In addition, this review also discusses and compares the advantages/disadvantages and development prospects of different pretreatment and analysis methods to provide a reference for further research.

Insights on the Extraction and Analysis of Phenolic Compounds from Citrus Fruits: Green Perspectives and Current Status

Citrus fruits (CF) are highly consumed worldwide, fresh, processed, or prepared as juices and pies. To illustrate the high economic importance of CF, the global production of these commodities in 2021 was around 98 million tons. CF's composition is considered an excellent source of phenolic compounds (PC) as they have a large amount and variety. Since ancient times, PC has been highlighted to promote several benefits related to oxidative stress disorders, such as chronic diseases and cancer. Recent studies suggest that consuming citrus fruits can prevent some of these diseases. However, due to the complexity of citrus matrices, extracting compounds of interest from these types of samples, and identifying and quantifying them effectively, is not a simple task. In this context, several extractive and analytical proposals have been used. This review discusses current research involving CF, focusing mainly on PC extraction and analysis methods, regarding advantages and disadvantages from the perspective of Green Chemistry.

New Levan-Based Chiral Stationary Phases: Synthesis and Comparative HPLC Enantioseparation of (±)-trans-β-Lactam Ureas in the Polar Organic Mode

In this paper, the preparation of three new polysaccharide-type chiral stationary phases (CSPs) based on levan carbamates (3,5-dimethylphenyl, 4-methylphenyl, and 1-naphthyl) is described. The enantioseparation of (±)-trans-β-lactam ureas 1a-h was investigated by high-performance liquid chromatography (HPLC) on six different chiral columns (Chiralpak AD-3, Chiralcel OD-3, Chirallica PST-7, Chirallica PST-8, Chirallica PST-9, and Chirallica PST-10) in the polar organic mode, using pure methanol (MeOH), ethanol (EtOH), and acetonitrile (ACN). Apart from the Chirallica PST-9 column (based on levan tris(1-naphthylcarbamate), the columns exhibited a satisfactory chiral recognition ability for the tested trans-β-lactam ureas 1a-h.

Discrimination of plastic waste pyrolysis oil feedstocks using supercritical fluid chromatography

Advanced chemical recycling techniques provide new avenues for handling and recycling mixed plastic waste; pyrolysis is a prominent approach involving heating plastic waste in an oxygen-free environment to create pyrolysis oils. Pyrolysis oils must be thoroughly characterized before being refined into fuels and chemical feedstocks. Here, a method based on supercritical fluid chromatography with ultraviolet detection was developed to analyze plastic waste pyrolysis oils. Multiple stationary phases were examined, and 2-ethyl pyridine was chosen as the best stationary phase for resolving pyrolysis oil components. Different standards and different plastic waste pyrolysis oils were compared across the different stationary phases. Up to three columns were serially coupled to increase efficiency and column capacity. It was found that a general method using ethanol as a modifier and two 2-ethyl pyridine columns could effectively resolve plastic waste pyrolysis oils. The potential for differentiating polyethylene and polypropylene feedstocks was demonstrated using principal component analysis.

Matrix effect in bioanalytical assay development using supercritical fluid chromatography-mass spectrometry

Matrix effect (ME) is commonly caused by coelution of compounds with target analytes, resulting in either suppression or enhancement of analyte ionization. Thus, to achieve the desired accuracy, precision, and sensitivity, ME needs to be evaluated and controlled during bioanalytical method development. As the application of supercritical fluid chromatography-mass spectrometry (SFC-MS) for analysis of biological samples has increased, ME using SFC-MS has also been investigated with a focus on the difference in ME in SFC-MS compared to other chromatographic techniques used for achiral separation in biological samples. Here, we provide a summary of the status of ME evaluation and mitigation in SFC-MS methods. This review presents an overview of the phenomenon of ME and methods for evaluating ME in bioanalysis. Next, the factors that can impact ME in SFC-MS-based bioanalytical methods are discussed in detail with an emphasis on SFC. A literature review of the evaluation of ME in targeted bioanalytical methods using SFC-MS is included at the end. Robust instrumentation, effective sample preparation, and superb separation selectivity are the foundations of reliable analytical methods as well as the ability to mitigate detrimental ME in SFC-MS methods.

Synthesis and evaluation of aromatic stationary phases based on linear solvation energy relationship model for expanded application in supercritical fluid chromatography

In the last decade, the separation application based on aromatic stationary phases has been demonstrated in supercritical fluid chromatography (SFC). In this paper, four aromatic stationary phases involving aniline (S-aniline), 1-aminonaphthalene (S-1-ami-naph), 1-aminoanthracene (S-1-ami-anth) and 1-aminopyrene (S-1-ami-py) were synthesized based on full porous particles (FPP) silica, which were not end-capped for providing extra electrostatic interaction. Retention mechanism of these phases in SFC was investigated using a linear solvation energy relationship (LSER) model. The aromatic stationary phases with five positive parameters (a, b, s, e and d+) can provide hydrogen bonding, π-π, dipole-dipole and cation exchange interactions, which belong to the moderate polar phases. The LSER results obtained using routine test solutes demonstrated that the aforementioned interactions of four aromatic stationary phases were influenced by the type and bonding density of the ligand, but to a certain extent. Furthermore, the LSER data verified that the S-1-ami-anth column based on full porous particles silica had higher cation exchange capacity (d+ value), compared to the commercialized 1-AA column (based on the ethylene-bridged hybrid particles). The relationship between the d+ value and SFC additive was quantitatively proved so as to regulate electrostatic interaction reasonably. This value was greatly increased by phosphoric acid, slightly increased by trifluoroacetic acid and formic acid, but significantly reduced by ammonium formate and diethylamine. Taking the S-1-ami-naph column as an example, better peek shape of the flavonoids was obtained after the addition of 0.1 % phosphoric acid in MeOH while isoquinoline alkaloids were eluted successfully within 11 min after adding 0.1 % diethylamine in MeOH. Combined with the unique π-π interaction and controllable electrostatic interaction, the aromatic stationary phases in this study have been proven to have expandable application potential in SFC separation.

Supercritical fluid chromatography is not (only) normal-phase chromatography

Supercritical fluid chromatography (SFC), now using carbon dioxide as a major component of the mobile phase, has been known for over 60 years but still some misunderstandings remain about its capabilities. Amongst them, SFC is often described as a normal-phase chromatographic technique, based on different considerations: polarity of the stationary phase, elution order of the analytes, relative non-polarity of the mobile phase, non-linear retention behaviour, or adsorption retention mechanisms. All of these assumptions are true to a certain extent, and in certain circumstances. But also, all of these assumptions are wrong in different circumstances. In this paper, the criteria to categorize SFC as a normal-phase chromatographic method will be examined individually, considering all knowledge acquired from the early years of its development. Finally, it will appear that the "normal-phase" glass lens is greatly reducing the true extent of SFC's possibilities.

Ultra-Fast Ion Mobility Spectrometer for High-Throughput Chromatography

Fast chromatography systems especially developed for high sample throughput applications require sensitive detectors with a high repetition rate. These high throughput techniques, including various chip-based microfluidic designs, often benefit from detectors providing subsequent separation in another dimension, such as mass spectrometry or ion mobility spectrometry (IMS), giving additional information about the analytes or monitoring reaction kinetics. However, subsequent separation is required at a high repetition rate. Here, we therefore present an ultra-fast drift tube IMS operating at ambient pressure. Short drift times while maintaining high resolving power are reached by several key instrumental design features: short length of the drift tube, resistor network of the drift tube, tristate ion shutter, and improved data acquisition electronics. With these design improvements, even slow ions with a reduced mobility of just 0.94 cm2/(V s) have a drift time below 1.6 ms. Such short drift times allow for a significantly increased repetition rate of 600 Hz compared with previously reported values. To further reduce drift times and thus increase the repetition rate, helium can be used as the drift gas, which allows repetition rates of up to 2 kHz. Finally, these significant improvements enable IMS to be used as a detector following ultra-fast separation including chip-based chromatographic systems or droplet microfluidic applications requiring high repetition rates.

Unified chromatography in drug development: Exploiting chaotropic/kosmotropic salts for an accelerated method development

Recent trends in supercritical fluid chromatography (SFC) introduced an innovative gradient profile called Unified Chromatography (UC), which pushes the amount of liquid modifier up to 80-100 % of the total mobile phase composition. These new conditions allow the full transition from a supercritical to a liquid state, unifying the benefits of both SFC and liquid chromatography. However, to facilitate the use of UC for industrial drug development, a stronger effort is needed to streamline and simplify its method development and optimization. In this work, a quick and novel method development procedure for UC is introduced, enabled by the first-time use of novel additives in SFC/UC that exploit chaotropic/kosmotropic properties. A comprehensive view on some fundamental properties, such as the amount of liquid modifier blended with supercritical CO2 (scCO2) and the percentage of water added in the mobile phase is given, to clarify the benefits of using either a chaotropic salt (NaClO4), kosmotropic (HCOONa) or salt with mixed properties (NaOMs - sodium methanesulfonate). With this expanded knowledge, challenging separations of nucleosides, nucleotide, indoles, triazoles and related derivates have been accomplished with UC. Finally, we provide an example of UC delivering a faster and better method for an AbbVie pipeline compound under accelerated stability study. The combined use of scCO2-based chromatography and the novel additive NaClO4 ensures the retention and elution of all degradation species generated at different conditions, where RP-HPLC failed to provide satisfactory performance.

Applicability of supercritical fluid chromatography for oligonucleotide analysis: A proof-of-concept study

We evaluated the suitability of supercritical fluid chromatography (SFC) for oligonucleotide analysis using 4-mer oligonucleotides with various phosphorothioate (PS) contents as model compounds. Column screening showed that the diol-modified column was able to separate sequences with different PS contents. Optimization of the column body and additives allowed us to analyze polar oligonucleotides using SFC. Various sequences were also analyzed using the optimized method. A good peak shape was obtained when the guanine plus cytosine content of the analyte was two or less in the 4-mer oligonucleotides. Furthermore, we found that the retention times of the selected sequences were positively correlated with polar surface areas, indicating that oligonucleotides interact with polar stationary phases. In contrast, more hydrophobic full PS sequences were retained more strongly in the diol column than the full phosphodiester (PO) sequences. This suggests that the diol column has unique selectivity for PO and PS linkages. These results indicate that SFC is potentially applicable to oligonucleotide analysis with a separation mechanism that is different from that of ion-pair reversed-phase liquid chromatography.

Facilitated on-line supercritical fluid extraction - supercritical fluid chromatography for nonpolar and polar compounds from milk thistle seeds

Plant seeds, as those from milk thistle (Silybum marianum), are a valuable source of nonpolar and polar compounds with potentially interesting biological activity. The main nonpolar compounds are triglycerides, which are also the main components of all vegetable oils. In addition, specific polar compounds - flavonolignans, called silymarin, have been found in large amounts in milk thistle seeds extract. These flavonoids derivatives have different biological activity, for instance hepatoprotective effects. In order to extract and analyze both nonpolar (triglycerides) and polar compounds (flavonolignans) from milk thistle seeds through a sequential methodology, an on-line supercritical fluid extraction - supercritical fluid chromatography (SFE-SFC) method was developed. Different ways of transferring the extracts from SFE to SFC (i.e. direct on-column transfer and loop transfer) were compared, and particularly for their effect on chromatographic quality. In this respect, nonpolar and polar compounds caused different issues, especially as polar compounds required a significant portion of co-solvent in the extraction step, favoring early elution in the chromatographic column. First, on-line SFE-SFC was used for triglycerides analysis and allowed the comparison of transfer modes. Then, on-line kinetics were performed to measure defatting time before polar molecules extraction. Finally, the eventual benefit of loop transfer was also investigated for the analysis of flavonolignans, polar molecules whose analysis can be difficult by on-line SFE-SFC. The aim of this paper is to discuss the versatility of on-line SFE-SFC and how challenging the coupling can be, especially when both non-polar and polar molecules must be analyzed independently in a single sample.

Synthesis, identification, chiral separation and crystal structure of (3R,4R,7S,8S)-3,4,7,8-tetrachlorodecane and its stereoisomers

Chlorinated paraffins (CPs) are a notoriously known class of compounds that stand amongst the most wide-spread persistent organic pollutants. Therefore, their reliable, repeatable, and reproducible quantitative analysis using well-defined reference standards is of utmost importance. In view of the increasing demand for constitutionally and stereochemically defined CP standards, we have synthesized a stereoisomeric mixture of 3,4,7,8-tetrachlorodecane. One stereoisomer - (3R,4R,7S,8S)-3,4,7,8-tetrachlorodecane was separated from the mixture, and enriched fractions of residual stereoisomers were achieved through crystallisation of the residual mother liquors. The molecular structure of the single isolated stereoisomer was confirmed through single-crystal X-ray crystallographic data. One fraction of 3,4,7,8-tetrachlorodecane stereoisomers was successfully separated on a chiral stationary phase using supercritical fluid chromatography hyphenated to mass spectrometry (column: Chiral ART Amylose-C; mobile phase: CO₂/MeOH (96/4 v/v) with 0.1% diethylamine). The reported separation of stereoisomers is unprecedented in CP analysis so far.

An attempt to apply a subtraction model for characterization of non-polar stationary phase in supercritical fluid chromatography

This study verified the feasibility of using a subtraction model to characterize the non-polar stationary phases (including C4, C8, and phenyl-type) in supercritical fluid chromatography (SFC). The model with 6 terms was expressed as log α = η'H + θ'P + β'A + α'B + κ'C + σ'S, where a term θ'P indicating dipole or induced dipole interaction was intentionally supplemented. Ethylbenzene and SunFire C8 were respectively defined as the reference solute and column. A 7-step modeling procedure was proposed: in the first 6 steps, except σ'S, by the use of a bidirectional fitting method, other parameters were calculated based on the equation: log α = log (k_i/k_ref) ≈ η'H + θ'P + β'A + α'B + κ'C; and in the 7th step, residual analysis was employed to describe the σ'S term according to the equation: σ'S = log α_exp. - log α_pre. Furthermore, six columns that were not involved in modeling process and 12 compounds with unknown retention were used for methodology validation. It showed good predictions of log k, as demonstrated by adjusted determination coefficient (R²_adj) from 0.9927 to 0.9998 (column) and from 0.9940 to 0.9999 (compound), respectively. The subtraction model emphasized the contribution of dipole or induced dipole interaction to the retention in SFC, and it obtained the σ'S term through residual analysis. Moreover, it made reasonable physical-chemical sense as the linear solvation energy relationship (LSER) model did, with the distinct advantages of better fitting and more accurate prediction. This study provided some new insights into the characterization of non-polar stationary phases in SFC.

A fast ultra performance supercritical fluid chromatography-tandem mass spectrometric method for profiling of targeted phytosterols

Phytosterols are essential structural components of plant cell membranes and possess health-related benefits, including lowering blood cholesterol levels in humans. Numerous analytical methods are being used to profile plant and animal sterols. Chromatography hyphenated to tandem mass spectrometry, is a better option due to its specificity, selectivity, and sensitivity. An ultra-performance supercritical fluid chromatography hyphenated with atmospheric pressure chemical ionization (APCI) tandem mass spectrometric method was developed and evaluated for fingerprint analysis of seven phytosterols. Mass spectrometry fragmentation behavior was used for phytosterol identification, and multiple reaction monitoring scanning was utilized for phytosterol confirmation, where APCI outperformed superiority in terms of ion intensity, particularly in the production of [M + H-H₂O]⁺ ions rather than [M + H]⁺ ions. The chromatographic conditions were thoroughly evaluated, and the ionization parameters were optimized as well. In a 3 min. run, the seven phytosterols were separated concurrently. The calibration and repeatability tests were conducted to check the instrument's performance, and the results indicated that all of the phytosterols tested had correlation coefficients (r²) greater than 0.9911 over the concentration range of 5-5000 ng/mL. The limit of quantification was below 20 ng/mL for all the tested analytes except for stigmasterol and campesterol. The partially validated method was applied for the evaluation of phytosterols in pure coconut oil and palm oil in order to demonstrate its applicability. Total sterols in coconut and palm oils were 126.77 ng/mL and 101.73 ng/mL, respectively. In comparison to earlier methods of phytosterol analysis, the novel method offers a far faster, more sensitive, and more selective analytical process.

Revisiting Disinfection Byproducts with Supercritical Fluid Chromatography-High Resolution-Mass Spectrometry: Identification of Novel Halogenated Sulfonic Acids in Disinfected Drinking Water

High resolution mass spectrometry (HRMS) coupled to either gas chromatography or reversed-phase liquid chromatography is the generic method to identify unknown disinfection byproducts (DBPs) but can easily overlook their highly polar fractions. In this study, we applied an alternative chromatographic separation method, supercritical fluid chromatography-HRMS, to characterize DBPs in disinfected water. In total, 15 DBPs were tentatively identified for the first time as haloacetonitrilesulfonic acids, haloacetamidesulfonic acids, and haloacetaldehydesulfonic acids. Cysteine, glutathione, and p-phenolsulfonic acid were found as precursors during lab-scale chlorination, with cysteine providing the highest yield. A mixture of the labeled analogues of these DBPs was prepared by chlorination of ¹³C₃-¹⁵N-cysteine and analyzed using nuclear magnetic resonance spectroscopy for structural confirmation and quantification. A total of 6 drinking water treatment plants utilizing various source waters and treatment trains produced sulfonated DBPs upon disinfection. Those were widespread in the tap water of 8 cities across Europe, with estimated concentrations up to 50 and 800 ng/L for total haloacetonitrilesulfonic acids and haloacetaldehydesulfonic acids, respectively. Up to 850 ng/L haloacetonitrilesulfonic acids were found in 3 public swimming pools. Considering the stronger toxicity of haloacetonitriles, haloacetamides, and haloacetaldehydes than the regulated DBPs, these newly found sulfonic acid derivatives may also pose a health risk.

An in-depth investigation of supercritical fluid chromatography retention mechanisms by evaluation of a series of specially designed alkylsiloxane-bonded stationary phases based on linear solvation energy relationship

Fundamental research on supercritical fluid chromatography (SFC) has gained considerable interest, with many studies focusing on its retention mechanism based on the linear solvation energy relationship (LSER) model. In this paper, a series of alkylsiloxane-bonded stationary phases were specifically designed and synthesized, then evaluated using the mobile phase composed of CO₂ with 10% (v/v) methanol. The study demonstrated the close relationship between the interactions (manner and magnitude) of stationary phases and the C-chain length, bonding density and the endcapping treatment. All C8 phases provide positive e, v and negative s, whose magnitude was regularly affected by bonding density. It was worth mentioning the non-endcapped C8 phases could provide H-bonding (positive a and b) by reducing the bonding density of the alkyl chain. Once it was endcapped, the interaction manner did not vary with bonding density adjustment. The non-endcapped C4 phases with higher bonding density could establish additional dispersion interaction (positive v). It can be seen that two synthesis strategies, 1) non-endcapped, long C-chain (C8) combined with low bonding density, and 2) non-endcapped, short C-chain (C4) combined with high bonding density, can obtain the alkylsiloxane-bonded stationary phases (C8-1 and C4-3) to provide both polar and dispersion interactions, showing different separation selectivity. Furthermore, the LSER model with ionic terms was applied to evaluate partial C8 columns, and its rationality was verified. The non-endcapped C8 showed great d⁺ values, which originated from the silanol groups. C8SCX also possessed a great d⁺ value due to the benzenesulfonic acid groups. A remarkable result showed that C8SAX exhibited prominent d^- and d⁺ values simultaneously due to the combined effect of silanol and quaternary ammonium groups, which indicates the unique selectivity when separating ionic compounds. This study provides in-depth insights into the retention mechanism of alkylsiloxane-bonded stationary phases in SFC, as well as a reference for the design of SFC stationary phases.

Online SFE-SFC-MS/MS colony screening: A high-throughput approach for optimizing (-)-limonene production

Conventional analysis of microbial bioproducers requires the extraction of metabolites from liquid cultures, where the culturing steps are time consuming and greatly limit throughput. To break through this barrier, the current study aims to directly evaluate microbial bioproduction colonies by way of supercritical fluid extraction-supercritical fluid chromatography-triple quadrupole mass spectrometry (SFE-SFC-MS/MS). The online SFE-SFC-MS/MS system offers great potential for high-throughput analysis due to automated metabolite extraction without any need for pretreatment. This is the first report of SFE-SFC-MS/MS as a method for direct colony screening, as demonstrated in the high-throughput screening of (-)-limonene bioproducers. Compared with conventional analysis, the SFE-SFC-MS/MS system enables faster and more convenient screening of highly productive strains.

Defining a generic column set for achiral supercritical fluid chromatography applied to pharmaceuticals or natural products

When starting a method development in supercritical fluid chromatography (SFC), the first step is usually to screen several stationary phases based on previous experience or simply based on what is available in the laboratory. However, as there are now a large number of stationary phases available for SFC, the choice of an adequate set of columns to rapidly achieve a satisfying result can be difficult. In this project, 16 columns comprising a wide diversity of stationary phases and polarities ranging from the most polar (like bare silica gel) to the least polar (like octadecylbonded-silica) were compared, based on the gradient analysis of 129 probe compounds. The set mostly comprised active pharmaceutical ingredients, natural products and a few metabolites. The columns were ranked with the help of Derringer desirability functions taking account of (i) the number of compounds eluted from the column, (ii) the elution time in a suitable time frame, (iii) the average peak width, (iv) the average peak symmetry and (v) the spreading of retention along the gradient time. The five criteria selected showed no correlation. Overall, it appeared that those columns that had a high overall score were good for several reasons, like bare silica gel, propanediol-bonded silica or pentabromobenzyloxy-bonded silica. Initially, the columns had been screened with a gradient elution starting from 5% co-solvent and ending with 50% co-solvent in CO₂. However, for some most retentive columns like amide-bonded silica, too many compounds remained non-eluted from the column. To examine this column more fairly, a second elution gradient was applied that ended with 100% co-solvent. This proved effective in restoring good overall performance through the elution of the most polar compounds.

Ultra-high-performance supercritical fluid chromatography-mass spectrometry for the analysis of organic contaminants in sediments

A nontarget screening method was developed based on D-optimal designs for ultra-high performance supercritical fluid chromatography with positive and negative electrospray ionization mode mass spectrometry. A mixture of organic contaminants such as pesticides, steroids, surfactants, phenolic and fatty acids, and polycyclic aromatic hydrocarbon derivatives, was used for the optimization. An aprotic mixture of dichloromethane and acetone [3:1] performed overall best as the injection solvent. The highest peak capacities (n) were accomplished at the shallowest gradient (1%B/min), ammonium formate (n = 378 in negative ionization mode), or ammonium acetate (n = 327 in positive ionization mode) in methanol as the modifier. Capillary voltage, make-up solvent flow rate, water, and additive concentration were the most significant factors for improving peak intensity: higher peak intensities were obtained at lower additive concentrations (5mM ammonium formate), and with 5% water in positive ionization mode. Conversely, water had detrimental effects in negative ionization mode. The optimized method was used to quantify organic contaminants in 17 freshwater sediment samples from Copenhagen, Denmark. Out of 50 monitored contaminants, 35 were detected in at least one sample. Further, the method has a potential for target and nontarget screening analysis of organic contaminants in solid matrices.

Gradient elution of hydroxyacetophenones by supercritical fluid chromatography with electrochemical detection

Linear gradient elution supercritical fluid chromatography with electrochemical detection was developed using hydroxyacetophenones as analytes. Separation was carried out with a diol column (4.6 mm id × 250 mm length, 5 μm) as a stationary phase and a mixture of supercritical carbon dioxide and methanol as a mobile phase, where the ratio of carbon dioxide and methanol was changed from 99:1 (v/v) to 60:40 (v/v). For the electrochemical detection, methanol containing 1.0 mol L^-1 ammonium acetate was used as a supporting electrolyte solution and + 1.2 V was applied to the electrochemical cell. We compared the performance of the present method to isocratic elution supercritical fluid chromatography, and the repeatability, linearity, and detection capability all showed better analytical parameters in the gradient elution. As such, we found that gradient elution supercritical fluid chromatography can achieve the faster separation and save resources compared to isocratic elution. Thus, the present method may contribute to the development of green analytical methods.

Supercritical Fluid Nanospray Mass Spectrometry

Supercritical fluids are typically electrosprayed using an organic solvent makeup flow to facilitate continuous electrical connection and enhancement of electrospray stability. This results in sample dilution, loss in sensitivity, and potential phase separation. Premixing the supercritical fluid with organic solvent has shown substantial benefits to electrospray efficiency and increased analyte charge state. Presented here is a nanospray mass spectrometry system for supercritical fluids (nSF-MS). This split flow system used small i.d. capillaries, heated interface, inline frit, and submicron emitter tips to electrospray quaternary alkyl amines solvated in supercritical CO₂ with a 10% methanol modifier. Analyte signal response was evaluated as a function of total system flow rate (0.5-1.5 mL/min) that is split to nanospray a supercritical fluid with linear flow rates between 0.07 and 0.42 cm/sec and pressure ranges (15-25 MPa). The nSF system showed mass-sensitive detection based on increased signal intensity for increasing capillary i.d. and analyte injection volume. These effects indicate efficient solvent evaporation for the analysis of quaternary amines. Carrier additives generally decreased signal intensity. Comparison of the nSF-MS system to the conventional SF makeup flow ESI showed 10-fold signal intensity enhancement across all the capillary i.d.s. The nSF-MS system likely achieves rapid solvent evaporation of the SF at the emitter point. The developed system combined the benefits of the nanoemitters, sCO₂, and the low modifier percentage which gave rise to enhancement in MS detection sensitivity.

Quality evaluation of Panax notoginseng (Burk.) F.H. Chen using supercritical fluid chromatography-mass spectrometry and chemical pattern recognition

An efficient supercritical fluid chromatography-mass spectrometry (SFC-MS) method was developed for the quality evaluation of Panax Notoginseng (Burk) F.H. Chen (P. notoginseng) by combination with chemical pattern recognition (CPR). Design of experiments (DoE) was applied to obtain optimal SFC-MS conditions. Several CPR methods including hierarchical cluster analysis (HCA), principal component analysis (PCA) and partial least squares discriminant analysis (PLS-DA) were employed to establish a classification model based on the peak areas and contents of 12 components in P. notoginseng in order to evaluate the quality difference according to the collecting time (Chunqi and Dongqi) and medicinal parts (fibrous root, rhizome, branch root, and main root). PLS-DA has proved to be a satisfactory method with accurate discrimination of the selected samples. The characteristic variables based on the variable importance in projection (VIP) values were selected using PLS-DA. Three characteristic components (ginsenoside Rg₂, ginsenoside Rg₁, ginsenoside Rb₁) with higher VIP values (>1) were chosen to further build the CPR model. Subsequently, the model was verified by testing another set of samples and the results indicated that the established model was satisfactory. PLS-DA models based on the peak areas of the 12 selected analytes in 30 batches of P. notoginseng could give accurate classification. The obtained results demonstrate that the developed method using SFC-MS and PLS-DA has a great potential for the quality assessment of P. notoginseng.

Measurement of the molecular diffusion coefficient and the effective longitudinal diffusion under supercritical fluid chromatography conditions in packed bed columns

The improvement of supercritical fluid chromatography (SFC) instrumentation enhanced its reliability and utility over the past decade. The further development of high speed and high resolution separations is however obstructed by the lack of accurate models for axial dispersion in SFC. This work is a first step to tackle this by developing more reliable methods to measure molecular (D_mol) and longitudinal diffusion (D_eff) in SFC, as these affect all aspects of separation efficiency. In the present contribution, we report on an improved method, to enable more flexible, reliable and accurate measurements of D_mol in SFC using commercial instrumentation. A two-column variant of the stopped-flow experiment is proposed as an adapted set-up for measuring the effective longitudinal diffusion coefficient D_eff in SFC-conditions. Using the set-ups for a number of test-compounds, it has been found that D_eff, and the coefficients describing its constituent sub-processes (cf. particle diffusion D_part and surface diffusion γ_sD_s), all vary in a linearly proportional way with the bulk diffusion coefficient D_mol within a high degree of accuracy. It has also been found that D_eff decreases much more sharply with increasing retention factor compared to LC. By applying the effective medium theory, it was found that the relative surface diffusion coefficient γ_sD_s/D_mol decreases strongly with retention factor for the investigated solutes and column, in contrary to what is typically observed in reversed phase liquid chromatography. Results indicate that this might be related to a change in retention behavior of the analytes. Obviously, more analytes and conditions need to be explored to complete this picture and the extend range of applicability of these observations.

Retention mechanisms of imidazoline and piperazine-related compounds in non-aqueous hydrophilic interaction and supercritical fluid chromatography based on chemometric design and analysis

The experimental design methodology based on central composite design of experiments was applied to compare the retention mechanisms in supercritical fluid chromatography (SFC) and non-aqueous hydrophilic interaction liquid chromatography (NA-HILIC). The selected set consists of 26 compounds that belong to imidazoline and serotonin receptor ligands. The different chemometric tools (multiple linear regression, principal component analysis, parallel factor analysis) were used to examine the retention, as well as to identify the most significant retention mechanisms. The retention mechanism was investigated on two different stationary phases (diol, and mixed-mode diol). In NA-HILIC, the mobile phase contains acetonitrile as a main component, and methanolic solution of ammonium formate (+ 0.1% of formic acid) as a modifier. The same mobile phase modifier was used in SFC, with a difference in the main component of the mobile phase which was CO₂. The retention behaviour differs significantly between HILIC and SFC conditions. The retention pattern in HILIC mode was more partition-like, while in SFC the solute-sorbent interactions allowed retention. The retention mechanism between mixed-mode diol and the diol phases varies depending on the applied chromatographic mode, e.g., in HILIC the type of stationary phase significantly affects the elution order, while in SFC this was not the case. The HILIC retention behaviour was influenced by the number of tertiary amines-aliphatic, and N atom-centred fragments in tested compounds. On the other hand, the number of pyrrole and pyridine rings in the structure of the compound showed correlation with their SFC retention, simultaneously increasing the molecular weight and rapid elution of larger compounds. It was found that temperature surprisingly plays a major role in SFC mode. The increase in temperature reduces the relative contribution of enthalpy factors to total retention, so the separation in SFC was more entropy-controlled. For further pharmaceutical research and optimization, the SFC would be considered more beneficial compared to HILIC since it gives good selectivity in separation of chosen impurities.

Simultaneous Quantitative Analysis of the Major Bioactive Compounds in Gentianae Radix and its Beverages by UHPSFC-DAD

This study presents the first ultra-high performance supercritical fluid chromatography-diode array detector (UHPSFC-DAD) assay for simultaneous quantitation of secoiridoids, iridoids, xanthones, and xanthone glycosides in Gentiana lutea L. Separation was reached within 12 min on an Acquity UPC2 BEH 2-EP column using CO2 and methanol with 5.5% water as mobile phases. Method validation for nine selected marker compounds (gentisin, isogentisin, swertiamarin, sweroside, gentiopicroside, loganic acid, amarogentin, gentioside, and its isomer) confirmed the assay's sensitivity, linearity, precision, and accuracy. The practical applicability was proven by the analysis of 13 root specimens and 10 commercial liquid preparations (seven liqueurs and three clear spirits). In all root batches, the secoiridoid gentiopicroside dominated (2.1-5.6%) clearly over all other metabolites. In the liqueurs, the metabolite content and distribution were extremely variable: while gentiopicroside was the main compound in four liqueurs, sweroside dominated in one preparation and loganic acid in two others. In contrast, measurable amounts of the metabolites were not detected in any of the examined clear spirits.

Ultrahigh-Performance Supercritical Fluid Chromatography and Detection of Multiple Biogenic Amines in Gentamicin Sulfate: Method Development Using Computer-Assisted Modeling

In order to solve the problem of difficult separation of various biogenic amines (BAs), which have similar structures or very different polarities, in gentamicin, by conventional liquid chromatography, a new ultrahigh-performance supercritical fluid chromatography (UHPSFC) method was developed. In this method, 10 BAs were derivatized precolumn using dansyl chloride and separated using a UHPSFC system. By computational simulation, complete separation of 10 BAs was successfully achieved. Detection was performed using a photodiode array (PDA) and single-quadrupole mass spectrometry (MS) together with electrospray ionization (ESI). A wide linear range (10-2500 ng/mL) was achieved, with the limits of detection (LODs) between 1.2 and 10.0 ng/mL and the limits of quantification (LOQs) between 5.0 and 25.0 ng/mL. Apart from high sensitivity, this UHPSFC-PDA/ESI-MS detection method also displayed high accuracy, the matrix effect was reduced by an appreciable extent, and the recovery rates of the 10 BAs were between 84.1 and 117.1%. For comparison, high-performance liquid chromatography-tandem mass spectrometry (MS/MS) was also used for the detection of underivatized BAs in gentamicin, showing good linearity and high sensitivity (LODs from 0.05 to 1.00 ng/mL and LOQs from 1.00 to 12.50 ng/mL) for all BAs except for spermine and spermidine. Although single-quadrupole MS is inferior to MS/MS in terms of sensitivity, the UHPSFC method could detect more BAs. It also achieved the quantification limits required for impurity determination, demonstrating a potential strategy to offer a map overview of possible BA presence in fermentation antibiotics.

Comprehensive profiling of Sanguisorba officinalis using off-line two-dimensional mixed-mode liquid chromatography × reversed-phase liquid chromatography, tandem high-resolution mass spectrometry, and molecular network

The profiling of natural products is important in modern biological sciences and new drug development. However, the separation and characterization of complex herbal extracts are significantly challenging for researchers in the biochemical field. Herein, an off-line two-dimensional mixed-mode LC × reversed-phase LC system is developed. Our system exhibits high orthogonality and is composed of a newly prepared stationary phase in the first dimension and a traditional C₁₈ phase in the second dimension, and is operated in combination with high-resolution MS and molecular network. Sanguisorba officinalis L. is studied using the proposed method owing to its bioactivity. With the aid of orthogonal separation, the ionization of the individual components is improved. The number of detected compounds and separated peaks are significantly increased when one-dimensional-LC is upgraded to two-dimensional-LC. In addition, 270 compounds (127 of which are tentatively characterized as new compounds, and further confirmation is needed) are successfully characterized based on their fragmentation patterns under the guidance of molecular network, while only 95 compounds are characterized using one-dimensional-LC and high-resolution MS. The results indicate that the developed off-line two-dimensional mixed-mode LC × reversed-phase LC, tandem high-resolution MS, and molecular network method is effective for profiling complex samples. This article is protected by copyright. All rights reserved.

An overview of poly (amide-amine) dendrimers functionalized chromatographic separation materials

Chromatography is one of the most important separation techniques in analytical chemistry. In which, the separation materials are the core for good separation results. Poly (amide-amine) dendrimers with regular three-dimensional structure, abundant terminal groups, controllable molecule chains, and unique cavities appear to have a positive impact on chromatographic separation materials. In the past decades, poly (amide-amine) grafted adsorbents and stationary phases have presented high grafting efficiency, controllable surface structure, good dispersion, and wide practical applications. In this review, the prepared poly (amide-amine) functionalized separation materials and their applications are systematically summarized. Functions, significance, structure-actvity relationships and benefits of poly (amide-amine) dendrimers in the proposed separation materials are discussed in detail. And we hope to provide a useful reference for the future development of chromatographic separation materials and inspire new discoveries in the study of poly (amide-amine) functionalized materials.