A screen-printed carbon electrode modified with a bismuth film and gold nanoparticles for simultaneous stripping voltammetric determination of Zn(II), Pb(II) and Cu(II)

In situ deposition of bismuth on pre-anodized screen-printed electrode for sensitive determination of Cd2+ in water and rice with a portable device

Electrochemical detection is favorable for the rapid and sensitive determination of heavy metal cadmium. However, the detection sensitivity needs to be further improved, and a portable, low-cost device is needed for on-site detection. Herein, an in-situ bismuth modified pre-anodized screen-printed carbon electrode (SPCE) was developed for Cd2+ determination by square wave anodic stripping voltammetry (SWASV). The in-situ bismuth modification enhances the enrichment of Cd2+, and together with pre-anodization improve the electron transfer rate of electrode, thus enhancing the detection sensitivity. The electrode modification method combines pre-anodization and in-situ bismuth deposition, which is very easy and effective. Furthermore, a self-made PSoC Stat potentiostat coupled with a stirring device was fabricated for portable and low-cost electrochemical detection. After comprehensive optimization, the developed method can reach a testing time of 3 min, a detection limit of 3.55 μg/L, a linear range of 5-100 μg/L, and a recovery rate of 91.7-107.1% in water and rice samples for Cd2+ determination. Therefore, our method holds great promise for the rapid, sensitive and on-site determination of Cd2+ in food samples.

Voltammetric sensor for an anti-cancer drug cisplatin based on bismuth nanoparticles/graphene modified glassy carbon electrode

A selective and sensitive voltammetric sensor for the measurement of the chemotherapy drug cisplatin was based on bismuth nanoparticles decorated on a graphene-modified glassy carbon electrode (BiNPs/Gr/GCE). The surface morphologies of electrode modifications were characterized using scanning electron microscopy (SEM). Electrochemical characteristics were evaluated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Differential pulse voltammetry (DPV) was employed to detect cisplatin oxidation. Under the optimal conditions, oxidation peak currents increased linearly with cisplatin concentration from 6.0 to 180 μM. The detection limit was calculated to be 4.4 μM and the limit of quantification was 14.7 μM. Analytical performance studies demonstrated the good electrode reproducibility and the selectivity of the BiNPs/Gr/GCE towards cisplatin detection. The developed cisplatin sensor was successfully utilized to measure cisplatin in samples of human serum. Recoveries ranged from 89 to 102% and the results from the developed sensor were concordant (P > 0.05) with the results of analysis by high-performance liquid chromatography coupled with ultraviolet detection.

Modification of electrodes with polymer nanocomposites: Application to the simultaneous determination of Zn(II), Cd(II), and Cu(II) in water samples

Currently, there is a need for fast and sensitive analytical methods for monitoring metals in water due to the progressive increase in the presence of metal ions in the environment. These metals reach the environment mainly from industrial activity and heavy metals are non-biodegradable. The present work evaluates different polymeric nanocomposites to carry out the simultaneous electrochemical determination of Cu, Cd, and Zn in water samples. Screen-printed carbon electrodes (SPCE) were modified with the nanocomposites, which were obtained by a mixture of graphene, graphite oxide, and polymers, such as polyethyleneimide, gelatin, and chitosan. These polymers have amino groups in their matrix, giving the nanocomposite the ability to retain divalent cations. However, the availability of these groups plays a fundamental role in the retention of these metals. The modified SPCEs were characterized by scanning electron microscopy, Fourier-transform infrared spectroscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. The electrode that presented the best performance was selected to determine the concentration of metal ions in water samples by square-wave anodic stripping voltammetry. The obtained detection limits were 0.23 μg L^-1, 0.53 μg L^-1, and 1.52 μg L^-1 for Zn(II), Cd(II), and Cu(II), respectively, with a lineal range of 0.1-50 μg L^-1. The obtained results made it possible to conclude that the method developed using the SPCE modified with the polymeric nanocomposite presented adequate LODs, reasonable sensitivity, selectivity, and reproducibility. Besides, this platform is an excellent tool for developing devices to simultaneously determine heavy metals in environmental samples.

Development of electrochemical Zn2+ sensors for rapid voltammetric detection of glucose-stimulated insulin release from pancreatic β-cells

Diabetes is a chronic disease characterized by elevated blood glucose levels resulting from absent or ineffective insulin release from pancreatic β-cells. β-cell function is routinely assessed in vitro using static or dynamic glucose-stimulated insulin secretion (GSIS) assays followed by insulin quantification via time-consuming, costly enzyme-linked immunosorbent assays (ELISA). In this study, we developed a highly sensitive electrochemical sensor for zinc (Zn2+), an ion co-released with insulin, as a rapid and low-cost method for measuring dynamic insulin release. Different modifications to glassy carbon electrodes (GCE) were evaluated to develop a sensor that detects physiological Zn2+ concentrations while operating within a biological Krebs Ringer Buffer (KRB) medium (pH 7.2). Electrodeposition of bismuth and indium improved Zn2+ sensitivity and limit of detection (LOD), and a Nafion coating improved selectivity. Using anodic stripping voltammetry (ASV) with a pre-concentration time of 6 min, we achieved a LOD of 2.3 μg/L over the wide linear range of 2.5-500 μg/L Zn2+. Sensor performance improved with 10-min pre-concentration, resulting in increased sensitivity, lower LOD (0.18 μg/L), and a bilinear response over the range of 0.25-10 μg/L Zn2+. We further characterized the physicochemical properties of the Zn2+ sensor using scanning electron microscopy (SEM), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). Finally, we demonstrated the sensor's capability to measure Zn2+ release from glucose-stimulated INS-1 β-cells and primary mouse islets. Our results exhibited a high correlation with secreted insulin and validated the sensor's potential as a rapid alternative to conventional two-step GSIS plus ELISA methods.

New Prospects in the Electroanalysis of Heavy Metal Ions (Cd, Pb, Zn, Cu): Development and Application of Novel Electrode Surfaces

The detection of toxic heavy metal ions, especially cadmium (Cd), lead (Pb), zinc (Zn), and copper (Cu), is a global problem due to ongoing pollution incidents and continuous anthropogenic and industrial activities. Therefore, it is important to develop effective detection techniques to determine the levels of pollution from heavy metal ions in various media. Electrochemical techniques, more specifically voltammetry, due to its properties, is a promising method for the simultaneous detection of heavy metal ions. This review examines the current trends related to electrode formation and analysis techniques used. In addition, there is a reference to advanced detection methods based on the nanoparticles that have been developed so far, as well as formation with bismuth and the emerging technique of screen-printed electrodes. Finally, the advantages of using these methods are highlighted, while a discussion is presented on the benefits arising from nanotechnology, as it gives researchers new ideas for integrating these technologies into devices that can be used anywhere at any time. Reference is also made to the speciation of metals and how it affects their toxicity, as it is an important subject of research.

Copper nanoparticle-decorated nitrogen-doped carbon nanosheets for electrochemical determination of paraquat

A new strategy to prepare copper (Cu) nanoparticles anchored in nitrogen-doped carbon nanosheets (Cu@CN) has been designed and the nanomaterial applied to the determination of paraquat (PQ). The nanocomposite materials were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and several other techniques. We found that the Cu nanoparticles are uniformly distributed on the carbon materials, providing abundant active sites for electrochemical detection. The electrochemical behavior of the Cu@CN-based PQ sensor was investigated by square-wave voltammetry (SWV). Cu@CN exhibited excellent electrochemical activity and PQ detection performance. The Cu@CN-modified glassy carbon electrode (Cu@CN/GCE) exhibited excellent stability, favorable sensitivity, and high selectivity under optimized conditions (enrichment voltage -0.1 V and enrichment time 400 s) of the SWV test. The detection range reached 0.50 nM to 12.00 μM, and the limit of detection was 0.43 nM with high sensitivity of 18 μA·μM^-1·cm^-2. The detection limit is 9 times better than that of the high-performance liquid chromatography method. The Cu@CN electrochemical sensor demonstrated excellent sensitivity and selectivity also in environmental water and fruit samples enabling its use in practical, rapid trace-level detection of PQ in environmental samples.

Simultaneous Sensing of Cd(II), Pb(II), and Cu(II) Using Gold Nanoparticle-Modified APTES-Functionalized Indium Tin Oxide Electrode: Effect of APTES Concentration

In this work, indium tin oxide (ITO) electrodes were functionalized with varying 3-aminopropyltriethoxysilane (APTES) concentration percentages (0.5, 0.75, 1.0, and 2.0 wt %) to obtain the optimum conditions for the assembly of the as-synthesized gold nanoparticles (AuNPs). The AuNP coverage, wettability, and electrochemical performance of the modified electrodes were evaluated. The AuNP/0.75% APTES-ITO-modified electrode exhibited uniform coverage of AuNPs and high electrochemical performance for the simultaneous detection of Cd(II), Pb(II), and Cu(II) ions. Under the optimum conditions, the AuNP/0.75% APTES-ITO-modified electrode showed a linear detection range of 5-120 ppb and limit of detection of 0.73, 0.90, and 0.49 ppb for the simultaneous detection of Cd(II), Pb(II), and Cu(II) ions, respectively, via square wave anodic stripping voltammetry. The modified electrode demonstrated good anti-interference toward other heavy metal ions, good reproducibility, and suitability for application in environmental sample analysis.

Functionalization of Screen-Printed Electrodes with Grape Stalk Waste Extract-Assisted Synthesized Silver and Gold Nanoparticles: Perspectives of Electrocatalytically Enhanced Determination of Uranyl Ion and Other Heavy Metals Ions

Recently, nanotechnology and nanoparticles (NPs) such as AgNPs and AuNPs have become important in analytical chemistry due to their great potential to improve the performance of electrochemical sensors. In this work, Ag and Au nanoparticles have been synthesized using a green route in which a grape stalk waste extract is used as a reducing agent to obtain metallic nanoparticles. These NPs were used to customize the surface of commercial screen-printed electrodes (SPCNFEs). The spin-coating method was used to modify commercial SPCNFEs under a nitrogen atmosphere. The resulting electrodes were used in a determination study of Cd(II), Pb(II), and U(VI) with differential pulse anodic stripping voltammetry (DPASV). The customized green AgNPs and AuNPs electrodes presented higher sensitivity and electroanalytical performance than the non-modified SPCNFE. The results showed that the best analytical parameters were obtained with the green, silver nanoparticle SPCNFEs, with a LOD of 0.12 μg L^-1 for Pb(II), which is a lower value compared to the most restrictive regulation guidelines. Additionally, the U(VI) ion was successfully determined using the developed G-AgNPs-SPCNFE in spiked tap water, showing comparable results with the ICP-MS technique.

Nanofibrillar biochar from industrial waste as hosting network for transition metal dichalcogenides. Novel sustainable 1D/2D nanocomposites for electrochemical sensing

Industrial wastes have become elective sustainable sources to obtain materials for electronic/electroanalytical purposes; on the other hand, easy and green strategies to include semiconductor 2D graphene-like materials in conductive networks are highly required. In this work, 1D/2D nanocomposites (NCs) based on nanofibrillar biochar (BH) from paper industry waste and transition metal dichalcogenides (TMDs: MoS₂, WS₂, MoSe₂, and WSe₂), were prepared in water via liquid phase exfoliation (LPE) using sodium cholate as bioderived surfactant. The TMD amount in the NCs has been carefully optimized, searching for the best compromise between electron transfer ability and electroanalytical performances. Four different water-dispersed BH-TMD NCs have been selected and comprehensively studied from the electrochemical point of view and morphologically characterized. The BH-TMDs potentiality have been demonstrated in model solutions and real samples towards different analytes of biological and agri-food interest. The most performing NCs have been selected and used for the simultaneous determination of the neurotransmitters dopamine (DP) and serotonin (SR), and the flavonoids quercetin (QR) and rutin (RT), obtaining good linearity (R² ≥ 0.9956) with limits of detection ranging from 10 to 200 nM. Reproducible quantitative recovery values (90-112%, RSD ≤6%, n = 3) were obtained analyzing simultaneously DP and SR in synthetic biological fluid and drugs, and QR and RT in food supplements, proving the usability of the proposed materials for real analyses. This work proves that BH-nanofibers act as a sustainable conductive hosting network for 2D-TMDs, allowing full exploit their electroanalytical potential. The proposed BH-TMD NCs represent a sustainable, affordable, and captivating opportunity for the electrochemical and (bio)sensoristic field.

An antifouling gel-protected iridium needle sensor: Long-term, on-site monitoring of copper in seawater

Copper (Cu), a natural micronutrient with ecotoxicological significance, is involved in the carbon and nitrogen cycles occurring in marine ecosystems. Here, we developed a novel, antifouling gel-protected iridium (Ir) needle electrode modified with gold nanoparticles (G-IrNS) for long-term continuous and steady Cu monitoring. The gel formed an efficient membrane that effectively prevented the fouling of the sensing surface and displayed anti-convective properties, ensuring that mass transport toward the sensor surface was wholly controlled via diffusion. The repeatability, reproducibility, and stability of G-IrNS showed that it was suitable for long-term and on-site monitoring of Cu in seawater. Cu concentrations were successfully measured via fixed-point continuous monitoring for >2 weeks and onboard continuous monitoring in Bohai Sea using one sensor. Moreover, the relationship between Cu concentrations measured on-site via G-IrNS and its dissolved concentration in Bohai Sea was evaluated. G-IrNS can be applied to other metal ions as well, especially for long-term automatic on-site monitoring, thereby providing a basis for further research.

Smartphone-based electrochemical analysis integrated with NFC system for the voltammetric detection of heavy metals using a screen-printed graphene electrode

The electrochemical determination of five heavy metals is demonstrated using a wireless and card-sized potentiostat coupled with a smartphone through near-field communication (NFC) technology. A smartphone application was customized to command the NFC potentiostat, collect real-time signals, process the data, and ultimately display the quantities of the selected elements. The screen-printed graphene electrode (SPGE) was simply fabricated and modified using different nanomaterials for each heavy metal. Using differential pulse voltammetry (DPV) mode on the smartphone, the signal peaks were presented at + 10 mV for As(III), + 350 mV for Cr(VI), 0 mV for Hg(II), - 900 mV for Cd(II), and - 680 mV vs. Ag/AgCl for Pb(II). The linear ranges were 25-500, 250-25,000, 100-1,500, 25-750, 25-750 ng mL^-1 with detection limits of 3.0, 40, 16, 2.0, and 0.95 ng mL^-1 for As(III), Cr(VI), Hg(II), Cd(II), and Pb(II), respectively. The reproducibility in terms of relative standard deviation was less than 8.8% (n = 5 devices) of the developed SPGE coupled with the NFC potentiostat. Various samples for different applications (e.g., food safety and environmental monitoring) were analyzed and quantified using the proposed sensors. The results from this sensor indicate that there is no significant difference (95% confidence level) compared with those obtained from the traditional ICP-OES method, while the recoveries were found in the acceptable range of 80-111%. Hence, it can be deduced that this recent advanced technology of the NFC potentiostat developed for heavy metal analysis offers a highly sensitive and selective detection, yet the sensor remains compact, low-cost, and readily accessible to end-users.

Self-Assembled Iron Oxide Nanoparticle-Modified APTES-ITO Electrode for Simultaneous Stripping Analysis of Cd(II) and Pb(II) Ions

Carboxyl (−COOH)-stabilized iron oxide nanoparticles (IONPs) synthesized through co-precipitation were used to modify an indium tin oxide (ITO) electrode, which was chemically functionalized with 3-aminopropyltriethoxysilane (APTES) for heavy metal detection. The effect of soaking time (30, 60, 90, and 120 min) of IONP-COOH self-assembled on an APTES-ITO electrode was studied. Cyclic voltammetry and scanning electron microscopy were applied to analyze the electrochemical properties and morphologies of IONP-COOH/APTES-ITO modified electrode. The modified electrodes were then employed for the simultaneous detection of Cd(II) and Pb(II) by using square wave anodic stripping voltammetry. At 90 min of soaking time, excellent electrochemical performance and larger effective surface area (A_e) were obtained. The linear range for the simultaneous detection of Cd(II) and Pb(II) ions using the modified electrode was 10–100 ppb with limits of detection of 0.90 and 0.60 ppb, respectively. The interference study revealed a low interference effect from Cr(III), Hg(II), Zn(II), Cu(II), Mg(II), Na(I), and K(I) toward the simultaneous detection of Cd(II) and Pb(II). Finally, the IONP-COOH/APTES-ITO-modified electrode was applied to analyze seawater samples and was able to simultaneously detect Cd(II) and Pb(II) ions.

A novel approach to design electrochemical aptamer-based biosensor for ultrasensitive detecting of zearalenone as a prevalent estrogenic mycotoxin

BACKGROUND

Zearalenone is a well-known estrogenic mycotoxin produced by Fusarium species, a serious threat to the agricultural and food industries worldwide. Zearalenone, with its known metabolites, are biomarkers of exposure to certain fungi, primarily through food. It has considerable toxic effects on biological systems due to its carcinogenicity, mutagenicity, renal toxicity, teratogenicity, and immunotoxicity.

INTRODUCTION

This study aims to design a simple, quick, precise, and cost-effective method on a biosensor platform to evaluate the low levels of this toxin in foodstuffs and agricultural products.

METHODS

An aptamer-based electrochemical biosensor was introduced that utilizes screen-printed gold electrodes instead of conventional electrodes. The electrode position process was employed to develop a gold nanoparticle-modified surface to enhance the electroactive surface area. Thiolated aptamers were immobilized on the surface of gold nanoparticles, and subsequently, the blocker and analyte were added to the modified surface. In the presence of a redox probe, electrochemical characterization of differential pulse voltammetry, cyclic voltammetry, and electrochemical impedance spectroscopy were used to investigate the various stages of aptasensor fabrication.

RESULTS

The proposed aptasensor for zearalenone concentration had a wide linear dynamic range covering the 0.5 pg/mL to 100 ng/mL with a 0.14 pg/mL detection limit. Moreover, this aptasensor had high specificity so that a non-specific analyte cannot negatively affect the selectivity of the aptasensor.

CONCLUSION

Overall, due to its simple design, high sensitivity, and fast performance, this aptasensor showed a high potential for assessing zearalenone in real samples, providing a clear perspective for designing a portable and cost-effective device.

A Perspective of the Comprehensive and Objective Assessment of Analytical Methods Including the Greenness and Functionality Criteria: Application to the Determination of Zinc in Aqueous Samples

The recently proposed concept of White Analytical Chemistry (WAC), referring to the Red-Green-Blue color model, combines ecological aspects (green) with functionality (red and blue criteria), presenting the complete method as “white”. However, it is not easy to carry out an overall quantitative evaluation of the analytical method in line with the WAC idea in an objective manner. This paper outlines the perspective of the future development of such a possibility by attempting to answer selected questions about the evaluation process. Based on the study consisting in the evaluation of selected model methods by a group of 12 independent analysts, it was shown how well individual criteria are assessed, whether the variability of assessments by different people is comparable for each criterion, how large it is, and whether averaging the scores from different researchers can help to choose the best method more objectively.

Fabrication strategies and surface tuning of hierarchical gold nanostructures for electrochemical detection and removal of toxic pollutants

The intensive research on the synthesis and characterization of gold (Au) nanostructures has been extensively documented over the last decades. These investigations allow the researchers to understand the relationships between the intrinsic properties of Au nanostructures such as particle size, shape, morphology, and composition to synthesize the Au nano/hybrid nanostructures with novel physicochemical properties. By tuning the properties above, these nanostructures are extensively employed to detect and remove trace amounts of toxic pollutants from the environment. This review attempts to document the achievements and current progress in Au-based nanostructures, general synthetic and fabrication strategies and their utilization in electrochemical sensing and environmental remediation applications. Additionally, the applications of Au nanostructures (e.g., as adsorbents, sensing platforms, catalysts, and electrodes) and advancements in the field of electrochemical sensing of different target analytes (e.g., proteins, nucleic acids, heavy metals, small molecules, and antigens) are summarized. The literature survey concludes the existing methods for the detection of toxic contaminants at various concentration levels. Finally, the existing challenges and future research directions on electrochemical sensing and degradation of toxic contaminants using Au nanostructures are defined.

Recent Advancement in Disposable Electrode Modified with Nanomaterials for Electrochemical Heavy Metal Sensors

Heavy metal pollution has gained global attention due to its high toxicity and non-biodegradability, even at a low level of exposure. Therefore, the development of a disposable electrode that is sensitive, simple, portable, rapid, and cost-effective as the sensor platform in electrochemical heavy metal detection is vital. Disposable electrodes have been modified with nanomaterials so that excellent electrochemical properties can be obtained. This review highlights the recent progress in the development of numerous types of disposable electrodes modified with nanomaterials for electrochemical heavy metal detection. The disposable electrodes made from carbon-based, glass-based, and paper-based electrodes are reviewed. In particular, the analytical performance, fabrication technique, and integration design of disposable electrodes modified with metal (such as gold, tin and bismuth), carbon (such as carbon nanotube and graphene), and metal oxide (such as iron oxide and zinc oxide) nanomaterials are summarized. In addition, the role of the nanomaterials in improving the electrochemical performance of the modified disposable electrodes is discussed. Finally, the current challenges and future prospect of the disposable electrode modified with nanomaterials are summarized.

A simple electrochemical sensor based on rGO/MoS2/CS modified GCE for highly sensitive detection of Pb(ii) in tobacco leaves

High-performance electrode modification materials play a crucial role in improving the sensitivity of sensor detection in electrochemical determination of heavy metals. In this study, a rGO/MoS₂/CS nanocomposite modified glassy carbon electrode (GCE) was used to construct a sensitive sensor for detecting lead ions in tobacco leaves. The reduced graphene oxide (rGO) was used to increase the conductivity of the sensor, and the nano-flowered MoS₂ could provide a large reaction specific surface area and a certain active site for heavy metal reaction. Chitosan (CS) was used to improve the enrichment ability of heavy metals and increase the electrocatalytic activity of electrode. Thus, an electrochemical sensor with excellent performance in reproducibility, stability and anti-interference ability was established. The stripping behavior of Pb(ii) and the application conditions of the sensor were studied by square wave anodic stripping voltammetry (SWASV). The investigation indicated that the sensor exhibited high detection sensitivity in the range of 0.005-0.05-2.0 μM, and the limit of detection (LOD) was 0.0016 μM. This work can provide a fast and effective method for determination of Pb(ii) in samples with low content, such as tobacco leaves.

Polymethylolacrylamide/AuNPs Nanocomposites: Electrochemical Synthesis and Functional Characteristics

In this study the advantages of the electrochemical approach to the formation of polymer/metal nanoparticle composites are demonstrated. The method enables one to simplify the multistage processes of traditional technologies for the production of such materials through combining all intermediate processes in one stage and reducing the total formation time to 3–10 min. The possibility of a single-stage formation of a polymethylolacrylamide/AuNPs composite through including AuNPs into an electrically non-conducting polymethylolacrylamide film (carrier) formed by electropolymerization through potentiostatic electrolysis is also demonstrated for the first time. It is established that the addition of tetrachloroauric acid (HAuCl₄·4H₂O) into a monomeric composition containing acrylamide, formaldehyde, N,N′-methylene-bis-acrylamide, zinc chloride, and H₂O results in simultaneous electrochemical initiation of polymerization with the formation of a polymer film on the cathode, electrolytic reduction of gold ions to Au⁰, and immobilization of AuNPs particles into the growing polymer matrix. It was found that the formation of the PMAA / AuNPs composite is energetically more favorable than the synthesis of the main PMAA film, since it proceeds at a lower cathodic potential. The inclusion of AuNPs into the polymethylolacrylamide film was confirmed visually, as well as by X-ray phase analysis, small-angle X-ray scattering, microscopy, and element analysis. The gold content in the composite increases along with the increase of the concentration of HAuCl₄ in the electrolyte. The radius of the AuNPs particles was found to range between 3 and 7 nm. The AuNPs particles are spherical in shape and can combine into larger clusters containing up to 10 or more particles. The dynamics of formation, structure, and morphology of the polymethylolacrylamide/AuNPs composite were investigated. It was revealed that gold nanoparticles are mainly concentrated in the near-electrode and near-solution layers of the composite. We found that the composite has electrocatalytic activity. The possibility of its use as a sensor for hydrogen peroxide is demonstrated.

Comprehensive Assessment of Flow and Other Analytical Methods Dedicated to the Determination of Zinc in Water

An original strategy to evaluate analytical procedures is proposed and applied to verify if the flow-based methods, generally favorable in terms of green chemistry, are competitive when their evaluation also relies on other criteria. To this end, eight methods for the determination of zinc in waters, including four flow-based ones, were compared and the Red–Green–Blue (RGB) model was exploited. This model takes into account several features related to the general quality of an analytical method, namely, its analytical efficiency, compliance with the green analytical chemistry, as well as practical and economic usefulness. Amongst the investigated methods, the best was the flow-based spectrofluorimetric one, and a negative example was that one involving a flow module, ICP ionization and MS detection, which was very good in analytical terms, but worse in relation to other aspects, which significantly limits its overall potential. Good assessments were also noted for non-flow electrochemical methods, which attract attention with a high degree of balance of features and, therefore, high versatility. The original attempt to confront several worldwide accepted analytical strategies, although to some extent subjective and with limitations, provides interesting information and indications, establishing a novel direction towards the development and evaluation of analytical methods.

Electrochemical Determination of Lead & Copper Ions Using Thiolated Calix[4]arene-Modified Screen-Printed Carbon Electrode

This study used a thiolated calix[4]arene derivative modified on gold nanoparticles and a screen-printed carbon electrode (TC4/AuNPs/SPCE) for Pb2+ and Cu2+ determination. The surface of the modified electrode was characterised via Fourier-transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). Differential pulse voltammetry (DPV) was used for the detection of Pb2+ and Cu2+ under optimum conditions. The limit of detection (LOD) for detecting Pb2+ and Cu2+ was 0.7982 × 10−2 ppm and 1.3358 × 10−2 ppm, respectively. Except for Zn2+ and Hg2+, the presence of competitive ions caused little effect on the current response when detecting Pb2+. However, all competitive ions caused a significant drop in the current response when detecting Cu2+, except Ca2+ and Mg2+, suggesting the sensing platform is more selective toward Pb2+ ions rather than copper (Cu2+) ions. The electrochemical sensor demonstrated good reproducibility and excellent stability with a low relative standard deviation (RSD) value in detecting lead and copper ions. Most importantly, the result obtained in the analysis of Pb2+ and Cu2+ had good recovery in river water, demonstrating the applicability of the developed sensor for real samples.

Fluorescent sensor based on triphenylamine for Zn2+ with high selectivity and imaging in living cells

It is of great importance to design a fluorescent sensor with high selectivity, sensitivity and large Stokes shift to zinc detection for environmental water sample and in vivo. Herein, A novel Zn²⁺ fluorescent sensor with larger Stokes shift (110 nm) 1-((5-(4-(diphenylamino)phenyl)pyridine-2-imino)methyl)naphthalene-2-ol (abbr. TPA-PN) was designed and synthesized. In DMF-H₂O (V: V = 1: 1, pH = 7.0) solution, it could achieve high selectivity and sensitivity to Zn²⁺, there was a linear responsive range of 0-20 μM of concentration of Zn²⁺ ions for the sensor, the detection limit was as low as 19.134 nM and the binding constant was calculated to be 3.24 × 10⁴ M^-1. The species of TPA-PN and zinc were clarified at different pH. Besides, the interaction properties and fluorescence mechanism were demonstrated by the species theory, density functional theory (DFT) calculation, ¹H NMR titration, FT-IR and MS. Most importantly, it provided a new real-time, on-site method and showed excellent potential in-vivo imaging ability.

Bismuth Film-Coated Gold Ultramicroelectrode Array for Simultaneous Quantification of Pb(II) and Cd(II) by Square Wave Anodic Stripping Voltammetry

The widespread presence of heavy metals in drinking water sources arises as a major health concern, particularly in developing countries. The development of low-cost and reliable detection techniques is identified as a societal need to provide affordable water quality control. Herein, a bismuth film-coated gold ultramicroelectrode array (BF-UMEA) was used for the detection of Pb(II) and Cd(II) in water samples via square wave anodic stripping voltammetry (SWASV). Experimental parameters such as deposition time, Bi(III) concentration, acetate buffer concentration, pH, square wave frequency, amplitude, and step potential were all varied to determine their effects on the current peak intensities of the target metal ions. Ten-fold excess in the concentration of interferences was found to cause a decrease in the stripping peak areas of Cd(II) and Pb(II) in the following order of magnitude: benzene < NaCl < Ni(II) < Cu(II). Using Box-Behnken design, the optimum SWASV parameters that provided maximum current peak areas were 14.76 Hz (frequency), 50.10 mV (amplitude), and 8.76 mV (step potential). The limits of detection of the as-prepared BF-UMEA were 5 and 7 µg L^-1 for Pb(II) and Cd(II), respectively. These results demonstrate the potential use of a BF-UMEA in SWASV for the trace quantification of Pb(II) and Cd(II) in water samples.

Novel flexible bifunctional amperometric biosensor based on laser engraved porous graphene array electrodes: Highly sensitive electrochemical determination of hydrogen peroxide and glucose

Polyimide-laser-engraved porous graphene (LEPG) are hopeful electrode modification materials for flexible electrochemical sensing based on its high-efficiency preparation and low cost. Herein, a flexible, multi-patterned, and miniaturized electrode was fabricated via a simple and novel direct laser engraving. 3D LEPG with porous network structure can selective decorated with Pt nanoparticles (Pt NPs) by in situ electrochemical depositions (Pt-LEPG) as sensitively H₂O₂ sensors with a wide range of linear (0.01-29 nM) and high sensitivity (575.75 μA mM^-1 cm^-2). Subsequently, a glucose biosensor was successfully constructed through immobilized glucose oxidases (GOD) onto Pt-LEPG electrode. New-designed GOD/Pt-LEPG glucose sensor exhibited a noteworthy lower limit of detection (0.3 μM, S/N = 3) and high sensitivity (241.82 μA mM^-1 cm^-2), as much a wide-range of linear (0.01-31.5 mM) at near-neutral pH conditions, enabling detect glucose in real human serum specimens with satisfactory results. Predictably, these outstanding performance sensors have great potential in terms of flexible and wearable electronics.

Nanocomposites for Electrochemical Sensors and Their Applications on the Detection of Trace Metals in Environmental Water Samples

The elevated concentrations of various trace metals beyond existing guideline recommendations in water bodies have promoted research on the development of various electrochemical nanosensors for the trace metals' early detection. Inspired by the exciting physical and chemical properties of nanomaterials, advanced functional nanocomposites with improved sensitivity, sensitivity and stability, amongst other performance parameters, have been synthesized, characterized, and applied on the detection of various trace metals in water matrices. Nanocomposites have been perceived as a solution to address a critical challenge of distinct nanomaterials that are limited by agglomerations, structure stacking leading to aggregations, low conductivity, and limited porous structure for electrolyte access, amongst others. In the past few years, much effort has been dedicated to the development of various nanocomposites such as; electrochemical nanosensors for the detection of trace metals in water matrices. Herein, the recent progress on the development of nanocomposites classified according to their structure as carbon nanocomposites, metallic nanocomposites, and metal oxide/hydroxide nanocomposites is summarized, alongside their application as electrochemical nanosensors for trace metals detection in water matrices. Some perspectives on the development of smart electrochemical nanosensors are also introduced.

An impedimetric immunosensor for determination of porcine epidemic diarrhea virus based on the nanocomposite consisting of molybdenum disulfide/reduced graphene oxide decorated with gold nanoparticles

An electrochemical immunosensor for the determination of porcine epidemic diarrhea virus (PEDV) is described. It was manufactured by using gold nanoparticles/molybdenum disulfide/reduced graphene oxide nanocomposites modified on the surface of a glassy carbon electrode (GCE). The independently developed monoclonal antibody of PEDV-2C11 was immobilized on the modified electrode at site of gold nanoparticles provided in the nanocomposites. The concentration of PEDV was quantified by measuring the changes in the charge transfer resistance of the electrode before and after the immunoreaction between antigen-antibody by using hexacyanoferrate(II)/(III) as the redox probe. The frequency range was 10^-1 to 10⁵ Hz at the amplitude of 10 mV and an applied potential of + 0.180 V. Based on the immunoreaction between PEDV antigen and PEDV-2C11 antibody in 0.1 M phosphate buffer containing 0.1 M KCl at 37.5 °C for 140 min, the relative change in impedance was proportional to the logarithmic value of PEDV concentrations in the range of 82.5 to 1.65 × 10⁴ TCID₅₀ mL^-1. Good reproducibility, stability, and specificity of the proposed immunosensor were obtained. It was successfully applied to the determination of PEDV in the spiked sample. Graphical abstractSchematic representation. a The preparation of AuNP/MoS₂/rGO composites. b Representation of modification and functioning of the label-free electrochemical immunosensor and the electrochemical impedimetric response obtained before (a) and after (b) incubation of PEDV.

Sensors Applied for the Detection of Pesticides and Heavy Metals in Freshwaters

Water is essential for every life living on the planet. However, we are facing a more serious situation such as water pollution since the industrial revolution. Fortunately, many efforts have been done to alleviate/restore water quality in freshwaters. Numerous sensors have been developed to monitor the dynamic change of water quality for ecological, early warning, and protection reasons. In the present review, we briefly introduced the pollution status of two major pollutants, i.e., pesticides and heavy metals, in freshwaters worldwide. Then, we collected data on the sensors applied to detect the two categories of pollutants in freshwaters. Special focuses were given on the sensitivity of sensors indicated by the limit of detection (LOD), sensor types, and applied waterbodies. Our results showed that most of the sensors can be applied for stream and river water. The average LOD was72.53±12.69 ng/ml (n=180) for all pesticides, which is significantly higher than that for heavy metals (65.36±47.51 ng/ml,n=117). However, the LODs of a considerable part of pesticides and heavy metal sensors were higher than the criterion maximum concentration for aquatic life or the maximum contaminant limit concentration for drinking water. For pesticide sensors, the average LODs did not differ among insecticides (63.83±17.42 ng/ml,n=87), herbicides (98.06±23.39 ng/ml,n=71), and fungicides (24.60±14.41 ng/ml,n=22). The LODs that differed among sensor types with biosensors had the highest sensitivity, while electrochemical optical and biooptical sensors showed the lowest sensitivity. The sensitivity of heavy metal sensors varied among heavy metals and sensor types. Most of the sensors were targeted on lead, cadmium, mercury, and copper using electrochemical methods. These results imply that future development of pesticides and heavy metal sensors should (1) enhance the sensitivity to meet the requirements for the protection of aquatic ecosystems and human health and (2) cover more diverse pesticides and heavy metals especially those toxic pollutants that are widely used and frequently been detected in freshwaters (e.g., glyphosate, fungicides, zinc, chromium, and arsenic).

Nitrogen-doped carbon frameworks decorated with palladium nanoparticles for simultaneous electrochemical voltammetric determination of uric acid and dopamine in the presence of ascorbic acid

A glassy carbon electrode (GCE) was modified with nitrogen-enriched carbon frameworks decorated with palladium nanoparticles (Pd@NCF/GCEs). The modified GCE is shown to be a viable tool for determination of uric acid (UA) and dopamine (DA) in the presence of ascorbic acid (AA). The Pd@NCF was fabricated though one-step pyrolysis and characterized by X-ray photoelectron spectroscopy, X-ray diffraction, scanning electron microscopy and nitrogen-adsorption/desorption analysis. The Pd@NCF/GCE was characterized by differential pulse voltammetry (DPV). Both UA and DA have pronounced oxidation peaks (at 360 mV for UA and 180 mV for DA, all vs. Ag/AgCl) in the presence of AA. Response is linear in the 0.5-100 μM UA concentration range and in the 0.5-230 μM DA concentration range. The detection limits are 76 and 107 nM, respectively (at S/N = 3). This electrode is stable, reproducible and highly selective. It was used for UA and DA determination in spiked serum samples. Graphical abstractSchematic representation of nitrogen-enriched carbon frameworks decorated with palladium nanoparticles co-modified glassy carbon electrode for simultaneous determination of dopamine and uric acid in the presence of ascorbic acid.

Bifunctional and highly sensitive electrochemical non-enzymatic glucose and hydrogen peroxide biosensor based on NiCo2O4 nanoflowers decorated 3D nitrogen doped holey graphene hydrogel

In this work, a simple strategy for fabricating a 3D nitrogen doped holey graphene hydrogel decorated with NiCo₂O₄ nanoflowers (NHGH/NiCo₂O₄) via a one-pot hydrothermal method with subsequent calcination is reported for the first time. The novel NHGH/NiCo₂O₄ nanocomposites featured high electrical conductivity, large and accessible surface areas, abundant active sites, and excellent electrocatalytic performance. Considering the excellent catalytic activity of NiCo₂O₄, a sensitive and bifunctional electrochemical non-enzymatic biosensor was established for the determination of glucose and hydrogen peroxide (H₂O₂). The obtained biosensor exhibited wide linear ranges (glucose: 0.005-10.95 mM; H₂O₂: 1-510 μM) and a low detection limits (glucose: 0.39 μM; H₂O₂: 0.136 μM) in alkaline solution (S/N = 3). Excellent electrocatalytic activity of this sensor was ascribed to the synergistic effects of the hybrid structure between the NiCo₂O₄ nanoflowers and NHGH. Furthermore, the sensitive biosensor also exhibited high selectivity and could be applied to determine glucose in real blood samples. Taken together, the results reveal that the proposed hybrid nanocomposite could be a promising electrochemical biosensor.

One pot synthesis of dandelion-like polyaniline coated gold nanoparticles composites for electrochemical sensing applications

In this work, we report a facile and green strategy for one pot and in-situ synthesis of a dandelion-like conductive polyaniline coated gold nanoparticle nanocomposites (Au@PANI). The Au@PANI was characterized by SEM, TEM, XRD, TGA, FTIR, UV-vis and conductivity measurement, respectively. Newly-designed Au@PANI materials possessed a significantly high conductivity and strong adsorption capability. Thus, the Au@PANI modified glassy carbon electrode (GCE) was utilized for construct a novel electrochemical sensor for the simultaneous assay of Pb²⁺ and Cu²⁺ using square wave anodic stripping voltammetry (SWASV). Under the optimized conditions, an excellent electrochemical response in the simultaneous of Pb²⁺ and Cu²⁺ with detection limit of 0.003 and 0.008 μM (S/N = 3), respectively. Moreover, the prepared sensors realized an excellent reproducibility, repeatability and long term stability, as well as reliable practical assays in real water samples. Besides, the possible formation mechanism and sensing mechanism of Au@PANI nanocomposites have been discussed in detail. We believe this study provides a novel method of fabrication of noble metal nanoparticles decorated conducting polymer materials for the electrochemical sensing applications.