Xylose metabolism in the fungus Rhizopus oryzae: effect of growth and respiration on L+-lactic acid production

Engineering of Saccharomyces cerevisiae for enhanced metabolic robustness and L-lactic acid production from lignocellulosic biomass

Metabolic engineering for high productivity and increased robustness is needed to enable sustainable biomanufacturing of lactic acid from lignocellulosic biomass. Lactic acid is an important commodity chemical used for instance as a monomer for production of polylactic acid, a biodegradable polymer. Here, rational and model-based optimization was used to engineer a diploid, xylose fermenting Saccharomyces cerevisiae strain to produce L-lactic acid. The metabolic flux was steered towards lactic acid through the introduction of multiple lactate dehydrogenase encoding genes while deleting ERF2, GPD1, and CYB2. A production of 93 g/L of lactic acid with a yield of 0.84 g/g was achieved using xylose as the carbon source. To increase xylose utilization and reduce acetic acid synthesis, PHO13 and ALD6 were also deleted from the strain. Finally, CDC19 encoding a pyruvate kinase was overexpressed, resulting in a yield of 0.75 g lactic acid/g sugars consumed, when the substrate used was a synthetic lignocellulosic hydrolysate medium, containing hexoses, pentoses and inhibitors such as acetate and furfural. Notably, modeling also provided leads for understanding the influence of oxygen in lactic acid production. High lactic acid production from xylose, at oxygen-limitation could be explained by a reduced flux through the oxidative phosphorylation pathway. On the contrast, higher oxygen levels were beneficial for lactic acid production with the synthetic hydrolysate medium, likely as higher ATP concentrations are needed for tolerating the inhibitors therein. The work highlights the potential of S. cerevisiae for industrial production of lactic acid from lignocellulosic biomass.

Development of a Strategy for L-Lactic Acid Production by Rhizopus oryzae Using Zizania latifolia Waste and Cane Molasses as Carbon Sources

As a biodegradable and renewable material, polylactic acid is considered a major environmentally friendly alternative to petrochemical plastics. Microbial fermentation is the traditional method for lactic acid production, but it is still too expensive to compete with the petrochemical industry. Agro-industrial wastes are generated from the food and agricultural industries and agricultural practices. The utilization of agro-industrial wastes is an important way to reduce costs, save energy and achieve sustainable development. The present study aimed to develop a method for the valorization of Zizania latifolia waste and cane molasses as carbon sources for L-lactic acid fermentation using Rhizopus oryzae LA-UN-1. The results showed that xylose derived from the acid hydrolysis of Z. latifolia waste was beneficial for cell growth, while glucose from the acid hydrolysis of Z. latifolia waste and mixed sugars (glucose and fructose) from the acid hydrolysis of cane molasses were suitable for the accumulation of lactic acid. Thus, a three-stage carbon source utilization strategy was developed, which markedly improved lactic acid production and productivity, respectively reaching 129.47 g/L and 1.51 g/L·h after 86 h of fermentation. This work demonstrates that inexpensive Z. latifolia waste and cane molasses can be suitable carbon sources for lactic acid production, offering an efficient utilization strategy for agro-industrial wastes.

Rhizopus oryzae for Fumaric Acid Production: Optimising the Use of a Synthetic Lignocellulosic Hydrolysate

The hydrolysis of lignocellulosic biomass opens an array of bioconversion possibilities for producing fuels and chemicals. Microbial fermentation is particularly suited to the conversion of sugar-rich hydrolysates into biochemicals. Rhizopus oryzae ATCC 20344 was employed to produce fumaric acid from glucose, xylose, and a synthetic lignocellulosic hydrolysate (glucose–xylose mixture) in batch and continuous fermentations. A novel immobilised biomass reactor was used to investigate the co-fermentation of xylose and glucose. Ideal medium conditions and a substrate feed strategy were then employed to optimise the production of fumaric acid. The batch fermentation of the synthetic hydrolysate at optimal conditions (urea feed rate 0.625mgL−1h−1 and pH 4) produced a fumaric acid yield of 0.439gg−1. A specific substrate feed rate (0.164gL−1h−1) that negated ethanol production and selected for fumaric acid was determined. Using this feed rate in a continuous fermentation, a fumaric acid yield of 0.735gg−1 was achieved; this was a 67.4% improvement. A metabolic analysis helped to determine a continuous synthetic lignocellulosic hydrolysate feed rate that selected for fumaric acid production while achieving the co-fermentation of glucose and xylose, thus avoiding the undesirable carbon catabolite repression. This work demonstrates the viability of fumaric acid production from lignocellulosic hydrolysate; the process developments discovered will pave the way for an industrially viable process.

Macroalgal Proteins: A Review

Population growth is the driving change in the search for new, alternative sources of protein. Macroalgae (otherwise known as seaweeds) do not compete with other food sources for space and resources as they can be sustainably cultivated without the need for arable land. Macroalgae are significantly rich in protein and amino acid content compared to other plant-derived proteins. Herein, physical and chemical protein extraction methods as well as novel techniques including enzyme hydrolysis, microwave-assisted extraction and ultrasound sonication are discussed as strategies for protein extraction with this resource. The generation of high-value, economically important ingredients such as bioactive peptides is explored as well as the application of macroalgal proteins in human foods and animal feed. These bioactive peptides that have been shown to inhibit enzymes such as renin, angiotensin-I-converting enzyme (ACE-1), cyclooxygenases (COX), α-amylase and α-glucosidase associated with hypertensive, diabetic, and inflammation-related activities are explored. This paper discusses the significant uses of seaweeds, which range from utilising their anthelmintic and anti-methane properties in feed additives, to food techno-functional ingredients in the formulation of human foods such as ice creams, to utilising their health beneficial ingredients to reduce high blood pressure and prevent inflammation. This information was collated following a review of 206 publications on the use of seaweeds as foods and feeds and processing methods to extract seaweed proteins.

Lactic acid production - producing microorganisms and substrates sources-state of art

Lactic acid is an organic compound produced via fermentation by different microorganisms that are able to use different carbohydrate sources. Lactic acid bacteria are the main bacteria used to produce lactic acid and among these, Lactobacillus spp. have been showing interesting fermentation capacities. The use of Bacillus spp. revealed good possibilities to reduce the fermentative costs. Interestingly, lactic acid high productivity was achieved by Corynebacterium glutamicum and E. coli, mainly after engineering genetic modification. Fungi, like Rhizopus spp. can metabolize different renewable carbon resources, with advantageously amylolytic properties to produce lactic acid. Additionally, yeasts can tolerate environmental restrictions (for example acidic conditions), being the wild-type low lactic acid producers that have been improved by genetic manipulation. Microalgae and cyanobacteria, as photosynthetic microorganisms can be an alternative lactic acid producer without carbohydrate feed costs. For lactic acid production, it is necessary to have substrates in the fermentation medium. Different carbohydrate sources can be used, from plant waste as molasses, starchy, lignocellulosic materials as agricultural and forestry residues. Dairy waste also can be used by the addition of supplementary components with a nitrogen source.

Lactic acid accumulation under heat stress related to accelerated glycolysis and mitochondrial dysfunction inhibits the mycelial growth of Pleurotus ostreatus

High temperature is a major threat to Pleurotus ostreatus cultivation. In this study, a potential mechanism by which P. ostreatus mycelia growth is inhibited under heat stress was explored. Lactate, as a microbial fermentation product, was found unexpectedly in the mycelia of P. ostreatus under heat stress, and the time-dependent accumulation and corresponding inhibitory effect of lactate on mycelial growth was further confirmed. The addition of a glycolysis inhibitor, 2-deoxy-D-glucose (2DG), reduced the lactate content in mycelia and slightly restored mycelial growth under high-temperature conditions, which indicated the accumulation of lactate can be inhibited by glycolysis inhibition. Further data revealed mitochondrial dysfunction under high-temperature conditions, with evidence of decreased oxygen consumption and adenosine triphosphate (ATP) synthesis and increased reactive oxygen species (ROS). The removal of ROS with ascorbic acid decreased the lactate content, and mycelial growth recovered to a certain extent, indicating lactate accumulation could be affected by the mitochondrial ROS. Moreover, metabolic data showed that glycolysis and the tricarboxylic acid cycle were enhanced. This study reported the accumulation of lactate in P. ostreatus mycelia under heat stress and the inhibitory effect of lactate on the growth of mycelia, which might provide further insights into the stress response mechanism of edible fungi. Key Points • Lactate can accumulate in Pleurotus ostreatus mycelia under heat stress and inhibit its growth. • The accumulation of lactate may be due to the acceleration of glycolysis and the dysfunction of mitochondria of P. ostreatus mycelia under high-temperature stress. • The glycolysis and tricarboxylic acid cycle of P. ostreatus mycelia were accelerated under high-temperature stress.

Production of Lactic Acid from Seaweed Hydrolysates via Lactic Acid Bacteria Fermentation

Biodegradable polylactic acid material is manufactured from lactic acid, mainly produced by microbial fermentation. The high production cost of lactic acid still remains the major limitation for its application, indicating that the cost of carbon sources for the production of lactic acid has to be minimized. In addition, a lack of source availability of food crop and lignocellulosic biomass has encouraged researchers and industries to explore new feedstocks for microbial lactic acid fermentation. Seaweeds have attracted considerable attention as a carbon source for microbial fermentation owing to their non-terrestrial origin, fast growth, and photoautotrophic nature. The proximate compositions study of red, brown, and green seaweeds indicated that Gracilaria sp. has the highest carbohydrate content. The conditions were optimized for the saccharification of the seaweeds, and the results indicated that Gracilaria sp. yielded the highest reducing sugar content. Optimal lactic acid fermentation parameters, such as cell inoculum, agitation, and temperature, were determined to be 6% (v/v), 0 rpm, and 30 °C, respectively. Gracilaria sp. hydrolysates fermented by lactic acid bacteria at optimal conditions yielded a final lactic acid concentration of 19.32 g/L.

Terrestrial Microorganisms: Cell Factories of Bioactive Molecules with Skin Protecting Applications

It is well known that terrestrial environments host an immense microbial biodiversity. Exposed to different types of stress, such as UV radiation, temperature fluctuations, water availability and the inter- / intra-specific competition for resources, terrestrial microorganisms have been evolved to produce a large spectrum of bioactive molecules. Bacteria, archaea, protists, fungi and algae have shown a high potential of producing biomolecules for pharmaceutical or other industrial purposes as they combine a sustainable, relatively low-cost and fast-production process. Herein, we provide an overview of the different bioactive molecules produced by terrestrial microorganisms with skin protecting applications. The high content in polyphenolic and carotenoid compounds produced by several strains, as well as the presence of exopolysaccharides, melanins, indole and pyrrole derivatives, mycosporines, carboxylic acids and other molecules, are discussed in the context of their antioxidant, photo-protective and skin-whitening activity. Relevant biotechnological tools developed for the enhanced production of high added value natural products, as well as the protecting effect of some antioxidant, hydrolytic and degrading enzymes are also discussed. Furthermore, we describe classes of microbial compounds that are used or have the potential to be used as antimicrobials, moisturizers, biosurfactants, pigments, flavorings and fragrances.

Rhizopus oryzae - Ancient microbial resource with importance in modern food industry

Filamentous fungi are microorganisms widely known for their diverse biochemical features. Fungi can efficiently invade a wide variety of substrates under operational conditions producing numerous bioproducts of interest, such as enzymes, organic acids, aromatic compounds and colorants. An additional interesting characteristic of some fungi is their safety classification for different uses, which guarantees that the bioproducts obtained from them do not contain any toxic component deleterious to humans. Rhizopus oryzae is among this group of fungi and is classified as a GRAS filamentous fungus, commonly used for production of some oriental traditional foods. It is mainly recognized as a good producer of lactic acid; however, its potential for other biotechnological processes is under study. This review analyzes and discusses the current scientific and technical contributions which may maximize the potential of R. oryzae as a producer of different compounds of industrial interest.

High-efficiency l-lactic acid production by Rhizopus oryzae using a novel modified one-step fermentation strategy

In this study, lactic acid fermentation by Rhizopus oryzae was investigated using the two different fermentation strategies of one-step fermentation (OSF) and conventional fermentation (CF). Compared to CF, OSF reduced the demurrage of the production process and increased the production of lactic acid. However, the qp was significantly lower than during CF. Based on analysis of μ, qs and qp, a novel modified OSF strategy was proposed. This strategy aimed to achieve a high final concentration of lactic acid, and a high qp by R. oryzae. In this strategy, the maximum lactic acid concentration and productivity of the lactic acid production stage reached 158g/l and 5.45g/(lh), which were 177% and 366% higher, respectively, than the best results from CF. Importantly, the qp and yield did not decrease. This strategy is a convenient and economical method for l-lactic acid fermentation by R. oryzae.

Using tobacco waste extract in pre-culture medium to improve xylose utilization for l-lactic acid production from cellulosic waste by Rhizopus oryzae

The aim of this work was to study the high-titer l-lactic acid production from cellulosic waste using Rhizopus oryzae. The tobacco waste water-extract (TWE) added with 5g/L glucose and 0.1g/L vitamin C was optimized as pre-culture medium for R. oryzae. Results found that compared to traditional pre-culture medium, it improved xylose consumption rate up to 2.12-fold and enhanced l-lactic acid yield up to 1.73-fold. The highest l-lactic acid concentration achieved was 173.5g/L, corresponding to volumetric productivity of 1.45g/Lh and yield of 0.860g/g total reducing sugar in fed-batch fermentation. This process achieves efficient production of polymer-grade l-lactic acid from cellulosic feedstocks, lowers the cost of fungal cell pre-culture and provides a novel way for re-utilization of tobacco waste.

New application of Bacillus strains for optically pure l-lactic acid production: general overview and future prospects

Members of the genus Bacillus are considered to be both, among the best studied and most commonly used bacteria as well as the most still unexplored and the most wide-applicable potent bacteria because novel Bacillus strains are continuously being isolated and used in various areas. Production of optically pure l-lactic acid (l-LA), a feedstock for bioplastic synthesis, from renewable resources has recently attracted attention as a valuable application of Bacillus strains. l-LA fermentation by other producers, including lactic acid bacteria and Rhizopus strains (fungi) has already been addressed in several reviews. However, despite the advantages of l-LA fermentation by Bacillus strains, including its high growth rate, utilization of various carbon sources, tolerance to high temperature, and growth in simple nutritional conditions, it has not been reviewed. This review article discusses new findings on LA-producing Bacillus strains and compares them to other producers. The future prospects for LA-producing Bacillus strains are also discussed.

Highly efficient rice straw utilization for poly-(γ-glutamic acid) production by Bacillus subtilis NX-2

Lignocellulosic biomass has been identified as an economic and environmental feedstock for future biotechnological production. Here, for the first time, poly-(γ-glutamic acid) (PGA) production by Bacillus subtilis NX-2 using rice straw is investigated. Based on two-stage hydrolysis and characteristic consumption of xylose and glucose by B. subtilis NX-2, a co-fermentation strategy was designed to better accumulate PGA in a 7.5L fermentor by two feeding methods. The maximum cumulative respective PGA production and PGA productivity were 73.0 ± 0.5 g L(-1) and 0.81 g L(-1) h(-1) by the continuous feeding method, with carbon source cost was saved by 84.2% and 42.5% compared with glucose and cane molasse, respectively. These results suggest that rice straw, a type of abundant, low-cost, non-food lignocellulosic feedstock, may be feasibly and efficiently utilized for industrial-scale production of PGA.

A metabolic-based approach to improve xylose utilization for fumaric acid production from acid pretreated wheat bran by Rhizopus oryzae

In this work, wheat bran (WB) was utilized as feedstock to synthesize fumaric acid by Rhizopus oryzae. Firstly, the pretreatment process of WB by dilute sulfuric acid hydrolysis undertaken at 100°C for 30min offered the best performance for fumaric acid production. Subsequently, through optimizing the seed culture medium, a suitable morphology (0.55mm pellets diameter) of R. oryzae was obtained. Furthermore, a metabolic-based approach was developed to profile the differences of intracellular metabolites concentration of R. oryzae between xylose (the abundant sugar in wheat bran hydrolysate (WBH)) and glucose metabolism. The xylitol, sedoheptulose 7-phosphate, ribulose 5-phosphate, glucose 6-phosphate, proline and serine were responsible for fumaric acid biosynthesis limitation in xylose fermentation. Consequently, regulation strategies were proposed, leading to a 149% increase in titer (up to 15.4g/L). Finally, by combinatorial regulation strategies the highest production was 20.2g/L from WBH, 477% higher than that of initial medium.

Microbial production of lactic acid

Lactic acid is an important commodity chemical having a wide range of applications. Microbial production effectively competes with chemical synthesis methods because biochemical synthesis permits the generation of either one of the two enantiomers with high optical purity at high yield and titer, a result which is particularly beneficial for the production of poly(lactic acid) polymers having specific properties. The commercial viability of microbial lactic acid production relies on utilization of inexpensive carbon substrates derived from agricultural or waste resources. Therefore, optimal lactic acid formation requires an understanding and engineering of both the competing pathways involved in carbohydrate metabolism, as well as pathways leading to potential by-products which both affect product yield. Recent research leverages those biochemical pathways, while researchers also continue to seek strains with improved tolerance and ability to perform under desirable industrial conditions, for example, of pH and temperature.

Overexpression of D-xylose reductase (xyl1) gene and antisense inhibition of D-xylulokinase (xyiH) gene increase xylitol production in Trichoderma reesei

T. reesei is an efficient cellulase producer and biomass degrader. To improve xylitol production in Trichoderma reesei strains by genetic engineering, two approaches were used in this study. First, the presumptive D-xylulokinase gene in T. reesei (xyiH), which has high homology to known fungi D-xylulokinase genes, was silenced by transformation of T. reesei QM9414 strain with an antisense construct to create strain S6-2-2. The expression of the xyiH gene in the transformed strain S6-2-2 decreased at the mRNA level, and D-xylulokinase activity decreased after 48 h of incubation. This led to an increase in xylitol production from undetectable levels in wild-type T. reesei QM9414 to 8.6 mM in S6-2-2. The T. reesei Δxdh is a xylose dehydrogenase knockout strain with increased xylitol production compared to the wild-type T. reesei QM9414 (22.8 mM versus undetectable). The copy number of the xylose reductase gene (xyl1) in T. reesei Δxdh strain was increased by genetic engineering to create a new strain Δ9-5-1. The Δ9-5-1 strain showed a higher xyl1 expression and a higher yield of xylose reductase, and xylitol production was increased from 22.8 mM to 24.8 mM. Two novel strains S6-2-2 and Δ9-5-1 are capable of producing higher yields of xylitol. T. reesei has great potential in the industrial production of xylitol.

Highly efficient production of L-lactic acid from xylose by newly isolated Bacillus coagulans C106

Cost-effective production of optically pure lactic acid from lignocellulose sugars is commercially attractive but challenging. Bacillus coagulans C106 was isolated from environment and used to produce l-lactic acid from xylose at 50°C and pH 6.0 in mineral salts medium containing 1-2% (w/v) of yeast extract without sterilizing the medium before fermentation. In batch fermentation with 85g/L of xylose, lactic acid titer and productivity reached 83.6g/L and 7.5g/Lh, respectively. When fed-batch (120+80+60g/L) fermentation was applied, they reached 215.7g/L and 4.0g/Lh, respectively. In both cases, the lactic acid yield and optical purity reached 95% and 99.6%, respectively. The lactic acid titer and productivity on xylose are the highest among those ever reported. Ca(OH)2 was found to be a better neutralizing agent than NaOH in terms of its giving higher lactic acid titer (1.2-fold) and productivity (1.8-fold) under the same conditions.

Jerusalem artichoke powder: a useful material in producing high-optical-purity l-lactate using an efficient sugar-utilizing thermophilic Bacillus coagulans strain

Jerusalem artichoke is a low-requirement crop, which does not interfere with food chain, and is a promising carbon source for industrial fermentation. Microbial conversion of such a renewable raw material to useful products, such as lactic acid, is an important objective in industrial biotechnology. In this study, high-optical-purity l-lactate was efficiently produced from the hydrolysates of Jerusalem artichoke powder by a thermophilic bacterium, Bacillus coagulans XZL4. High l-lactate production (134gl(-1)) was obtained using 267gl(-1) Jerusalem artichoke powder (total reducing sugars of 140gl(-1)) and 10gl(-1) of corn steep powder in fed-batch fermentation, with an average productivity of 2.5gl(-1)h(-1) and a yield of 0.96gg(-1) reducing sugars. The final product optical purity is 99%, which meets the requirement of lactic acid polymerization. Our study represents a cost-effective and promising method for polymer-grade l-lactate production using a cheap raw bio-resource.

Mutation-Screening in l-(+)-Lactic Acid Producing Strains by Ion Implantation

In this paper, in order to obtain some industrial strains with high yield of l-(+)-lactic acid, the wild type strain Lactobacillus casei CICC6028 was mutated by nitrogen ions implantation. By study, it was found that the high positive mutation rate was obtained when the output power was 10 keV and the dose of N(+) implantation was 50 × 2.6 × 10(13) ions/cm(2). In addition, the initial screening methods were also studied, and it was found that the transparent halos method was unavailable, for some high yield strains of l-(+)-lactic acid were missed. Then a mutant strain which was named as N-2 was isolated, its optimum fermentation temperature was 40°C and the l-(+)-lactic acid yield was 136 g/l compared to the original strain whose optimum fermentation temperature was 34°C and l-(+)-lactic acid production was 98 g/l. Finally, High Performance Liquid Chromatography method was used to analyze the purity of l-(+)-lactic acid that was produced by the mutant N-2, and the result showed the main production of N-2 was l-(+)-lactic acid.

Metabolic engineering of Rhizopus oryzae for the production of platform chemicals

Rhizopus oryzae is a filamentous fungus belonging to the Zygomycetes. It is among others known for its ability to produce the sustainable platform chemicals L: -(+)-lactic acid, fumaric acid, and ethanol. During glycolysis, all fermentable carbon sources are metabolized to pyruvate and subsequently distributed over the pathways leading to the formation of these products. These platform chemicals are produced in high yields on a wide range of carbon sources. The yields are in excess of 85 % of the theoretical yield for L: -(+)-lactic acid and ethanol and over 65 % for fumaric acid. The study and optimization of the metabolic pathways involved in the production of these compounds requires well-developed metabolic engineering tools and knowledge of the genetic makeup of this organism. This review focuses on the current metabolic engineering techniques available for R. oryzae and their application on the metabolic pathways of the main fermentation products.

Carbohydrate-active enzymes from the zygomycete fungus Rhizopus oryzae: a highly specialized approach to carbohydrate degradation depicted at genome level

BACKGROUND

Rhizopus oryzae is a zygomycete filamentous fungus, well-known as a saprobe ubiquitous in soil and as a pathogenic/spoilage fungus, causing Rhizopus rot and mucomycoses.

RESULTS

Carbohydrate Active enzyme (CAZy) annotation of the R. oryzae identified, in contrast to other filamentous fungi, a low number of glycoside hydrolases (GHs) and a high number of glycosyl transferases (GTs) and carbohydrate esterases (CEs). A detailed analysis of CAZy families, supported by growth data, demonstrates highly specialized plant and fungal cell wall degrading abilities distinct from ascomycetes and basidiomycetes. The specific genomic and growth features for degradation of easily digestible plant cell wall mono- and polysaccharides (starch, galactomannan, unbranched pectin, hexose sugars), chitin, chitosan, β-1,3-glucan and fungal cell wall fractions suggest specific adaptations of R. oryzae to its environment.

CONCLUSIONS

CAZy analyses of the genome of the zygomycete fungus R. oryzae and comparison to ascomycetes and basidiomycete species revealed how evolution has shaped its genetic content with respect to carbohydrate degradation, after divergence from the Ascomycota and Basidiomycota.

Two-stage utilization of corn straw by Rhizopus oryzae for fumaric acid production

Due to the abundant, low price characteristic, lots of efforts have been put into producing bulk chemical from lignocellulose biomass, but the low utility of xylose, which is the second main component in lignocellulose, becomes a bottleneck for efficient lignocellulose utilization. This study investigated a novel two-stage corn straw utilization strategy for fumaric acid production by Rhizopus oryzae. Fungal growth was approached in hydrolysates from acid hydrolysis of corn straw, contained 30 g/l xylose; and fumaric acid production was occurred in hydrolysates from enzymatic hydrolysis of the residue corn straw after acid hydrolysis, contained 80 g/l glucose. Under the optimal condition using this two-stage corn straw utilization strategy, the fumaric acid production, was up to 27.79 g/l, with the yield of 0.35 g/g, productivity of 0.33 g/l/h.

Chitosan production from hemicellulose hydrolysate of corn straw: impact of degradation products on Rhizopus oryzae growth and chitosan fermentation

AIMS

To examine the potential use of hemicellulose hydrolysate (HH) for the production of chitosan by Rhizopus oryzae and investigate the influence of contents in HH on mycelia growth and chitosan synthesis.

METHODS AND RESULTS

Compared to xylose medium, HH enhanced mycelia growth, chitosan content and production of R. oryzae by 10.2, 64.5 and 82.1%, respectively. During sulfuric acid hydrolysis of corn straw, sugars (glucose, galactose, etc) and inhibitors (formic acid, acetic acid and furfural) were generated. Acetic acid (2.14 g l(-1)) and formic acid (0.83 g l(-1)) were stimulative, while furfural (0.55 g l(-1)) was inhibitory. Inhibitors, at different concentrations, increased the mycelia growth and chitosan production by 24.5-37.8 and 60.1-207.1%.

CONCLUSIONS

HH of corn straw is a good source for chitosan production. Inhibitors in HH, at proper concentrations, can enhance chitosan production greatly.

SIGNIFICANCE AND IMPACT OF THE STUDY

This work for the first time reported chitosan production from HH. Chitosan production can be greatly enhanced by cheap chemicals such as inhibitors in HH.

Development and optimization of a culture medium for L-lactic acid production by Rhizopus oryzae using crude protein from dairy manure as a nitrogen source

Experiments were conducted using the crude protein in fresh dairy manure as the nitrogen source in the culture media for Rhizopus oryzae to produce L-lactic acid. Two uniform design experiments were carried out with one for optimizing seed culture while the other for best percent L-lactic acid production. Multiple linear regression and ANOVA analyses were employed to determine the most significant media components. Data from the first uniform design U6 (6(2)x 3), in which the experimental factors involved included nitrogen concentration (crude protein), spore concentration, and treatment duration, showed that the levels of these components in the optimal condition for the seed culture medium were 2.1 g/L nitrogen, 16 hour culture time, and 10(5) spore concentration. The biomass weight in the seed medium developed in this study reached 1.32 g/L, which was 48.3% higher than that of the control. The combination of culture time and nitrogen concentration was found to be most significant in influencing the biomass yield. In the second uniform design experiment, flask culture with five factors (glucose, nitrogen from dairy manure, ZnSO4, KH2PO4, and MgSO4) at eight levels was examined using the uniform design table U8 (8(5)) with the content of L-lactic acid as the evaluating response Y. The results showed that ZnSO4 had the most influence on L-lactic acid yield, followed by nitrogen and KH2PO4. The optimum culture medium in terms of lactic acid production consisted of 240 g/L glucose, 1.26 g/L crude protein, 1.05 g/L KH2PO4, and 0.25 g/L MnSO4, which could achieve a yield of 59.57% (7.1% higher than the control).