Biotreatment of high-salinity wastewater: current methods and future directions

A positive contribution to nitrogen removal by a novel NOB in a full-scale duck wastewater treatment system

Nitrite-oxidizing bacteria (NOB) are undesirable in the anaerobic ammonium oxidation (anammox)-driven nitrogen removal technologies in the modern wastewater treatment plants (WWTPs). Diverse strategies have been developed to suppress NOB based on their physiological properties that we have understood. But our knowledge of the diversity and mechanisms employed by NOB for survival in the modern WWTPs remains limited. Here, Three NOB species (NOB01-03) were recovered from the metagenomic datasets of a full-scale WWTP treating duck breeding wastewater. Among them, NOB01 and NOB02 were classified as newly identified lineage VII, tentatively named Candidatus (Ca.) Nitrospira NOB01 and Ca. Nitrospira NOB02. Analyses of genomes and in situ transcriptomes revealed that these two novel NOB were active and showed a high metabolic versatility. The transcriptional activity of Ca. Nitrospira could be detected in all tanks with quite different dissolved oxygen (DO) (0.01-5.01 mg/L), illustrating Ca. Nitrospira can survive in fluctuating DO conditions. The much lower Ca. Nitrospira abundance on the anammox bacteria-enriched sponge carrier likely originated from the intensification substrate (NO2 -) competition from anammox and denitrifying bacteria. In particular, a highlight is that Ca. Nitrospira encoded and treanscribed cyanate hydratase (CynS), amine oxidase, urease (UreC), and copper-containing nitrite reductase (NirK) related to ammonium and NO production, driving NOB to interact with the co-existed AOB and anammox bacteria. Ca. Nitrospira strains NOB01 and NOB02 showed quite different niche preference in the same aerobic tank, which dominanted the NOB communities in activated sludge and biofilm, respectively. In addition to the common rTCA cycle for CO2 fixation, a reductive glycine pathway (RGP) was encoded and transcribed by NOB02 likely for CO2 fixation purpose. Additionally, a 3b group hydrogenase and respiratory nitrate reductase were uniquely encoded and transcribed by NOB02, which likely confer a survival advantage to this strain in the fluctuant activated sludge niche. The discovery of this new genus significantly broadens our understanding of the ecophysiology of NOB. Furthermore, the impressive metabolic versatility of the novel NOB revealed in this study advances our understanding of the survival strategy of NOB and provides valuable insight for suppressing NOB in the anammox-based WWTP.

Study on the effect of volatile organic compounds on the treatment of high-salt wastewater by low-temperature evaporation

High-salinity wastewater, owing to its intricate composition and challenging treatment requirements, poses a significant hurdle in water environmental governance. In this study, low-temperature evaporation technology is used to tackle wastewater containing the volatile organic compound such as N,N-dimethylacetamide (DMAC). Utilisation of comprehensive approaches involving experimental testing, mathematical modelling, and Aspen Plus software simulations, The influence of DMAC on evaporation efficiency is researched through the following factors which encompassing its effects on boiling point elevation, partial molar activation energy, and the formation of by-products. Additionally, the comparation of the impact of temperature, ionic strength, intermolecular interactions on the evaporation rate and the concentration of the volatile component DMAC in the condensate is also conducted in this study. After conducting a multiple linear regression analysis of evaporation efficiency using the Statistical Product and Service Solutions (SPSS) tool, it was discovered that temperature serves as the primary determinant influencing the evaporation rate. Additionally, ionic strength impacts solution viscosity, intermolecular interactions, and saturated vapour pressure by altering the intermolecular forces, thereby indirectly influencing both the evaporation rate and the quality of condensate water. The comparative analysis of single-effect and double-effect evaporation indicates that the optimal operating condition for double-effect evaporation yields an evaporation rate of 70%, with a remarkable 88% reduction in steam consumption compared to single one. Based on heat and mass balance principles, the mathematical model for double-effect evaporation is established to offer crucial data support for practical industrial applications.

Degradation of organic mercury in high salt environments by a marine aerobic bacterium Alteromonas macleodii KD01

Mercury (Hg), particularly organic mercury, poses a global concern due to its pronounced toxicity and bioaccumulation. Bioremediation of organic mercury in high-salt wastewater faces challenges due to the growth limitations imposed by elevated Cl- and Na+ concentrations on microorganisms. In this study, an isolated marine bacterium Alteromonas macleodii KD01 was demonstrated to degrade methylmercury (MeHg) efficiently in seawater and then was applied to degrade organic mercury (MeHg, ethylmercury, and thimerosal) in simulated high-salt wastewater. Results showed that A. macleodii KD01 can rapidly degrade organic mercury (within 20 min) even at high concentrations (>10 ng/mL), volatilizing a portion of Hg from the wastewater. Further analysis revealed an increased transcription of organomercury lyase (merB) with rising organic mercury concentrations during the exposure process, suggesting the involvement of mer operon (merA and merB). These findings highlight A. macleodii KD01 as a promising candidate for addressing organic mercury pollution in high-salt wastewater.

Improvement in Salt Tolerance Ability of Pseudomonas putida KT2440

Pseudomonas putida KT2440 is a popular platform for bioremediation due to its robust tolerance to environmental stress and strong biodegradation capacity. Limited research on the salt tolerance of P. putida KT2440 has hindered its application. In this study, the strain KT2440 was tested to tolerate a maximum of 4% w/v NaCl cultured with minimal salts medium. Transcriptomic data in a high-salinity environment showed significant expression changes in genes in membrane components, redox processes, chemotaxis, and cellular catabolic processes. betB-encoding betaine-aldehyde dehydrogenase was identified from the transcriptome data to overexpress and enhance growth profile of the strain KT2440 in minimal salts medium containing 4% w/v NaCl. Meanwhile, screening for exogenous salt-tolerant genes revealed that the Na+/H+ antiporter EcnhaA from Escherichia coli significantly increased the growth of the strain KT2440 in 4% w/v NaCl. Then, co-expression of EcnhaA and betB (KT2440-EcnhaA-betB) increased the maximum salt tolerance of strain KT2440 to 5% w/v NaCl. Further addition of betaine and proline improved the salt tolerance of the engineered strain to 6% w/v NaCl. Finally, the engineered strain KT2440-EcnhaA-betB was able to degrade 56.70% of benzoic acid and 95.64% of protocatechuic acid in minimal salt medium containing 4% w/v NaCl in 48 h, while no biodegradation was observed in the normal strain KT2440 in the same conditions. However, the strain KT2440-EcnhaA-betB failed to degrade catechol in minimal salt medium containing 3% w/v NaCl. This study illustrated the improvement in the salt tolerance performance of Pseudomonas putida KT2440 and the feasibility of engineered strain KT2440 as a potential salt-tolerant bioremediation platform.

Bioplastic Production from Agri-Food Waste through the Use of Haloferax mediterranei: A Comprehensive Initial Overview

The research on bioplastics (both biobased and biodegradable) is steadily growing and discovering environmentally friendly substitutes for conventional plastic. This review highlights the significance of bioplastics, analyzing, for the first time, the state of the art concerning the use of agri-food waste as an alternative substrate for biopolymer generation using Haloferax mediterranei. H. mediterranei is a highly researched strain able to produce polyhydroxybutyrate (PHB) since it can grow and produce bioplastic in high-salinity environments without requiring sterilization. Extensive research has been conducted on the genes and pathways responsible for PHB production using H. mediterranei to find out how fermentation parameters can be regulated to enhance cell growth and increase PHB accumulation. This review focuses on the current advancements in utilizing food waste as a substitute for costly substrates to reduce feedstock expenses. Specifically, it examines the production of biomass and the recovery of PHB from agri-food waste. Furthermore, it emphasizes the characterization of PHB and the significance of hydroxyvalerate (HV) abundance in the formation of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) copolymer. The downstream processing options are described, and the crucial factors associated with industrial scale-up are assessed, including substrates, bioreactors, process parameters, and bioplastic extraction and purification. Additionally, the economic implications of various options are discussed.

Coupling dairy wastewaters for nutritional balancing and water recycling: sustainable heterologous 2-phenylethanol production by engineered cyanobacteria

Microalgae biotechnology is hampered by the high production costs and the massive usage of water during large-volume cultivations. These drawbacks can be softened by the production of high-value compounds and by adopting metabolic engineering strategies to improve their performances and productivity. Today, the most sustainable approach is the exploitation of industrial wastewaters for microalgae cultivation, which couples valuable biomass production with water resource recovery. Among the food processing sectors, the dairy industry generates the largest volume of wastewaters through the manufacturing process. These effluents are typically rich in dissolved organic matter and nutrients, which make it a challenging and expensive waste stream for companies to manage. Nevertheless, these rich wastewaters represent an appealing resource for microalgal biotechnology. In this study, we propose a sustainable approach for high-value compound production from dairy wastewaters through cyanobacteria. This strategy is based on a metabolically engineered strain of the model cyanobacterium Synechococcus elongatus PCC 7942 (already published elsewhere) for 2-phenylethanol (2-PE). 2-PE is a high-value aromatic compound that is widely employed as a fragrance in the food and cosmetics industry thanks to its pleasant floral scent. First, we qualitatively assessed the impact of four dairy effluents on cyanobacterial growth to identify the most promising substrates. Both tank-washing water and the liquid effluent of exhausted sludge resulted as suitable nutrient sources. Thus, we created an ideal buffer system by combining the two wastewaters while simultaneously providing balanced nutrition and completely avoiding the need for fresh water. The combination of 75% liquid effluent of exhausted sludge and 25% tank-washing water with a fine-tuning ammonium supplementation yielded 180 mg L-1 of 2-PE and a biomass concentration of 0.6 gDW L-1 within 10 days. The mixture of 90% exhausted sludge and 10% washing water produced the highest yield of 2-PE (205 mg L-1) and biomass accumulation (0.7 gDW L-1), although in 16 days. Through these treatments, the phosphates were completely consumed, and nitrogen was removed in a range of 74%-77%. Overall, our approach significantly valorized water recycling and the exploitation of valuable wastewaters to circularly produce marketable compounds via microalgae biotechnology, laying a promising groundwork for subsequent implementation and scale-up.

Mutualistic symbiosis of fungi and nitrogen-fixing bacteria in halophilic aerobic granular sludge treating nitrogen-deficient hypersaline organic wastewater

Hypersaline organic wastewater is characterized as being nitrogen-deficient, and is easily prone to sludge bulking. In this study, the stability of halophilic aerobic granular sludge (HAGS) for the treatment of hypersaline organic wastewater is explored. Along with the decrease of influent ammonium, the bacterial population substantially reduced, whereas the fungal population continuously increased in HAGS. Saccharomycetales in fungi become the dominant sequence (99.78%) in HAGS bulking. Additionally, Halanaerobium (77.47%) remained prevalent in HAGS despite bacterial washout. Halanaerobium, a nitrogen-fixing genus of bacteria, provided nitrogen for ammonium-assimilating fungi. Saccharomycetales encapsulating HAGS reduced the transfer efficiency of dissolved oxygen, thereby creating favorable growth conditions for Halanaerobium. This paper for the first time highlights the mutualistic symbiosis of fungi and bacteria in HAGS treating the hypersaline organic wastewater. The study lays the foundation for the control and recovery of HAGS bulking.

Biofilm reactors filled with Stick-bed Biofix and Swim-bed Biofringe biomass carriers in treating chitin production wastewater containing high salinity

The production of chitin generates wastewater containing high content of organic compounds, nutrients, and salinity, thus a biofilm system including anaerobic-anoxic-aerobic bioreactors was employed. This study aims to evaluate the performance of Stick-bed Biofix and Swim-bed Biofringe added to bioreactors as a biomass carrier in order to enhance biomass concentration. The results indicated that the organic removal has been insignificantly affected by high salinity, the removal efficiency was obtained at 95 ± 2% corresponding to a rate of 5.78 ± 1.10 kg COD/m3/d. Otherwise, the nitrogen removal rate was achieved at around 0.45 ± 0.17 kg N/m3/d and strongly decreased to 0.24 ± 0.10 kg N/m3/d under high salinity of 18,000 mg/L and a high loading rate of 1.03 ± 0.10 kg N/m3/d. Phosphorus removal was obtained at 0.032-0.057 kg P/m3/d and decreased by 1.5 times when the salinity is over 10,000 mg/L although the influent load was strongly reduced by pre-treatment. Besides, the biofilm system can also remove around 50% of calcium ions which causes high salinity in chitin production wastewater.

Salinity effect on an anaerobic methane- and ammonium-oxidising consortium: Shifts in activity, morphology, osmoregulation and syntrophic relationship

Nitrate-dependent anaerobic methane oxidation (AOM) is a microbial process of both ecological significance for global methane mitigation and application potential for wastewater treatment. It is mediated by organisms belonging to the archaeal family 'Candidatus Methanoperedenaceae', which have so far mainly been found in freshwater environments. Their potential distribution in saline environments and their physiological responses to salinity variation were still poorly understood. In this study, the responses of the freshwater 'Candidatus Methanoperedens nitroreducens'-dominated consortium to different salinities were investigated using short- and long-term setups. Short-term exposure to salt stress significantly affected nitrate reduction and methane oxidation activities over the tested concentration range of 15-200‰ NaCl, and 'Ca. M. nitroreducens' showed the higher tolerance to high salinity stress than its partner of anammox bacteria. At high salinity concentration, near marine conditions of 37‰, the target organism 'Ca. M. nitroreducens' showed stabilized nitrate reduction activity of 208.5 µmol day-1 gCDW-1 in long-term bioreactors over 300 days, in comparison to 362.9 and 334.3 µmol day-1 gCDW-1 under low-salinity conditions (1.7‰ NaCl) and control conditions (∼15‰ NaCl). Different partners of 'Ca.  M. nitroreducens' evolved in the consortia with three different salinity conditions, suggesting the different syntrophic mechanisms shaped by changes in salinity. A new syntrophic relationship between 'Ca. M. nitroreducens' and Fimicutes and/or Chloroflexi denitrifying populations was identified under the marine salinity condition. Metaproteomic analysis shows that the salinity changes lead to higher expression of response regulators and selective ion (Na+/H+) channeling proteins that can regulate the osmotic pressure between the cell and its environment. The reverse methanogenesis pathway was, however, not impacted. The finding of this study has important implications for the ecological distribution of the nitrate-dependent AOM process in marine environments and the potential of this biotechnological process for the treatment of high-salinity industrial wastewater.

Influence of Solid Retention Time on Membrane Fouling and Biogas Recovery in Anerobic Membrane Bioreactor Treating Sugarcane Industry Wastewater in Sahelian Climate

Sugarcane industries produce wastewater loaded with various pollutants. For reuse of treated wastewater and valorization of biogas in a Sahelian climatic context, the performance of an anaerobic membrane bioreactor was studied for two solid retention times (40 days and infinity). The pilot was fed with real wastewater from a sugarcane operation with an organic load ranging from 15 to 22 gCOD/L/d for 353 days. The temperature in the reactor was maintained at 35 °C. Acclimatization was the first stage during which suspended solids (SS) and volatile suspended solids (VSS) evolved from 9 to 13 g/L and from 5 to 10 g/L respectively, with a VSS/SS ratio of about 80%. While operating the pilot at a solid retention time (SRT) of 40 days, the chemical oxygen demand (COD) removal efficiency reached 85%, and the (VSS)/(TSS) ratio was 94% in the reactor. At infinity solid retention time, these values were 96% and 80%, respectively. The 40-day solid retention time resulted in a change in transmembrane pressure (TMP) from 0.0812 to 2.18 bar, with a maximum methane production of 0.21 L/gCOD removed. These values are lower than those observed at an infinite solid retention time, at which the maximum methane production of 0.29 L/gCOD was achieved, with a corresponding transmembrane pressure variation of up to 3.1 bar. At a shorter solid retention time, the fouling seemed to decrease with biogas production. However, we note interesting retention rates of over 95% for turbidity.

Improved simultaneous nitrification-denitrification in fixed-bed baffled bioreactors treating mariculture wastewater: Performance and microbial community behaviors

As mariculture develops, wastewater treatment becomes crucial. In this study, fixed-bed baffled reactors (FBRs) packed with carbon fiber (CFBR) or polyurethane (PFBR) as biofilm carriers were used for mariculture wastewater treatment. Under salinity shocks between 0.10 and 30.00 g/L, the reactors showed efficient and stable nitrogen removal capacities, and the maximum NH₄⁺-N removal rates were 107.31 and 105.42 mg/(L·d) for CFBR and PFBR, respectively, with an initial NH₄⁺-N concentration of 120.00 mg/L. Further, in the independent aerobic chambers of the FBRs for nitrogen removal, taxa enrichment varied depending on the biofilm carrier, and the assembly process was more deterministic in CFBR than in PFBR. Two distinct clusters representing the spatial distribution of the adhering and deposited sludge in CFBR and the front and rear compartments in PFBR were noted. Furthermore, microbial interactions were more numerous and stable in CFBR. These findings improve the application prospects of FBRs in mariculture wastewater treatment.

Mn(VII) enhanced by CaSO3 to remove trace organic pollutants in high salt organic wastewater: Further enhancement of salinity

The high concentration of salt in organic wastewater has a strong inhibitory effect on the removal of pollutants. A method for the efficient removal of trace pollutants in high-salinity organic wastewater was developed. This study investigated the effect of the combination of permanganate [Mn(VII)] and calcium sulfite [S(IV)] on pollutant removal in hypersaline wastewater. The Mn(VII)-CaSO₃ system removed more pollutants from high-salinity organic wastewater than from normal-salinity wastewater. Chloride (increasing from 1 M to 5 M) and low concentration of sulfate (increasing from 0.05 M to 0.5 M) significantly enhanced the system's resistance to pollutants under neutral conditions. Despite the fact that Cl^- can combine with the free radicals in the system and reduce their efficiency in removing pollutants, the presence of chloride ions greatly enhances the electron transfer rate in the system, promoting the conversion of Mn(VII) to Mn(III) and significantly increasing the reaction rate of Mn(III) as the primary active species. Therefore, chloride salts can greatly enhance the removal of organic pollutants by Mn(VII)-CaSO₃. Although sulfate does not react with free radicals, a high concentration of sulfate (1 M) will affect the formation of Mn(III), which greatly weakens the removal effect of the entire system on pollutants. The system can still have a good pollutant removal effect with mixed salt. Altogether, this study demonstrates that the Mn(VII)-CaSO₃ system offers new possibilities for the treatment of organic pollutants in hypersaline wastewater.

Purification and biochemical characterization of SM14est, a PET-hydrolyzing enzyme from the marine sponge-derived Streptomyces sp. SM14

The successful enzymatic degradation of polyester substrates has fueled worldwide investigation into the treatment of plastic waste using bio-based processes. Within this realm, marine-associated microorganisms have emerged as a promising source of polyester-degrading enzymes. In this work, we describe the hydrolysis of the synthetic polymer PET by SM14est, a polyesterase which was previously identified from Streptomyces sp. SM14, an isolate of the marine sponge Haliclona simulans. The PET hydrolase activity of purified SM14est was assessed using a suspension-based assay and subsequent analysis of reaction products by UV-spectrophotometry and RP-HPLC. SM14est displayed a preference for high salt conditions, with activity significantly increasing at sodium chloride concentrations from 100 mM up to 1,000 mM. The initial rate of PET hydrolysis by SM14est was determined to be 0.004 s^-1 at 45°C, which was increased by 5-fold to 0.02 s^-1 upon addition of 500 mM sodium chloride. Sequence alignment and structural comparison with known PET hydrolases, including the marine halophile PET6, and the highly efficient, thermophilic PHL7, revealed conserved features of interest. Based on this work, SM14est emerges as a useful enzyme that is more similar to key players in the area of PET hydrolysis, like PHL7 and IsPETase, than it is to its marine counterparts. Salt-tolerant polyesterases such as SM14est are potentially valuable in the biological degradation of plastic particles that readily contaminate marine ecosystems and industrial wastewaters.

Recent advances in the biological treatment of wastewater rich in emerging pollutants produced by pharmaceutical industrial discharges

Pharmaceuticals and personal care products present potential risks to human health and the environment. In particular, wastewater treatment plants often detect emerging pollutants that disrupt biological treatment. The activated sludge process is a traditional biological method with a lower capital cost and limited operating requirements than more advanced treatment methods. In addition, the membrane bioreactor combines a membrane module and a bioreactor, widely used as an advanced method for treating pharmaceutical wastewater with good pollution performance. Indeed, the fouling of the membrane remains a major problem in this process. In addition, anaerobic membrane bioreactors can treat complex pharmaceutical waste while recovering energy and producing nutrient-rich wastewater for irrigation. Wastewater characterizations have shown that wastewater's high organic matter content facilitates the selection of low-cost, low-nutrient, low-surface-area, and effective anaerobic methods for drug degradation and reduces pollution. However, to improve the biological treatment, researchers have turned to hybrid processes in which all physical, chemical, and biological treatment methods are integrated to remove various emerging contaminants effectively. Hybrid systems can generate bioenergy, which helps reduce the operating costs of the pharmaceutical waste treatment system. To find the most effective treatment technique for our research, this work lists the different biological treatment techniques cited in the literature, such as activated sludge, membrane bioreactor, anaerobic treatment, and hybrid treatment, combining physicochemical and biological techniques.

Growth performance of different forestry species irrigated with moderately saline wastewater

A seven month, pot study was conducted to evaluate the impact of moderately saline wastewater on the growth potential of six forestry plant species viz., Eucalyptus calmaldulensis, Dendrocalamus strictus, Casurina equisetfolia, Cassia fistula, Melia dubia, and Bambusa arundinacea under different drainage conditions namely, well-drained saline (WDS) condition and poor-drained saline condition (PDS) and the control with well-drained non-saline condition. WDS treatment resulted in no mortality whereas PDS treatment resulted in mortality in the range of 33-66%. The plant height and root dry biomass increased in the range of 145% to 221.6% and 4.3-37.1 g respectively in WDS treatment, however, 23.60% to 173.4% and 4.1-10.1 g in PDS treatment. Among all, Eucalyptus camaldulensis and Dendrocalamus strictus showed high Na+ accumulation in roots (2.16 ± 0.02% and 1.13 ± 0.01%), shoots (1.98 ± 0.01% and 0.74 ± 0.01%) and leaves (1.27 ± 0.02% and 0.86 ± 0.01%) in WDS treatment and in case of PDS treatment root (1.01 ± 0.01% and 0.23 ± 0.01%), shoot (1.12 ± 0.02% and 0.11 ± 0.01%), and leaf (0.07 ± 0.01% and 0.1 ± 0.02). The overall performance of both Eucalyptus camaldulensis and Dendrocalamus strictus was highest in WDS treatment. Therefore, it was concluded, that both plants had better performance than other plant species, a proper drainage system defines the overall productivity and treatment efficiency.

Lrp as a potential transcriptional regulator involved in stress response in Haloferax mediterranei

The Archaea domain consists of a heterogeneous group of microorganisms with unique physiological properties that occupy a wide variety of niches in nature. Haloferax mediterranei is an extremely halophilic archaeon classified in the Phylum Euryarchaeota, which requires a high concentration of inorganic salts for optimal growth. In haloarchaea, transcription factors play a fundamental role in an adequate adaptation to environmental and nutritional changes, preserving the survival and integrity of the organism. To deepen knowledge of the Lrp/AsnC transcriptional regulator family, a lrp gene (HFX_RS01210) from this family has been studied. Site-directed mutagenesis has allowed us to identify the TATA-box and two potential sites of the transcriptional factor (TF) to its own promoter and autoregulate itself. Several approaches were carried out to elucidate whether this transcriptional regulator is involved in stresses due to heavy metals and limited nitrogen conditions. Characterization of the lrp deletion mutant and the Lrp overexpressed strain, suggests that the level of lrp expression depends on the nitrogen source and the presence of cobalt. The most striking results were obtained in the presence of nitrate as a nitrogen source due to the inability of the deletion mutant to grow. All these results confirm that Lrp is a powerful candidate for a regulatory role in the stress response, particularly under N-limiting conditions and the presence of cobalt.

Spontaneous granulation of moderately halophilic sludge inoculated with saltern sediments from single granule into multi-granule aggregation

There is very limited research on the application of moderate halophiles for biotreatment of hypersaline wastewater widely generated from some industries. This study demonstrated the development of moderate halophiles inoculated from saltern sediments into aerobic granule sludge (AGS) to treat hypersaline wastewater with a salinity of 100 g/L. The granulation of moderate halophiles can occur without applying the settling velocity selective pressure. The saltern sediment initially aggregated into single small granules and finally developed into 1200 ± 50 μm multiparticle granules. The halophiles affiliated in Halomonas was dominant in the granular bacterial community, with a relative abundance of 94.52%. Halomonas ventosae secreted sulfated polysaccharides. The sulfated polysaccharides content accounted for 63.95 ± 2.10% in the polysaccharides (PS), having an adhesive role in connecting single granules. Multiparticle granules showed the clear stratified structure, with α-D-glucopyranose polysaccharides in the inner bounders and β-D-glucopyranose polysaccharides in the outer. The moderately granular sludge showed the stable chemical oxygen demand (COD) removal efficiency of >90% and the aerobic total inorganic nitrogen (TIN) removal efficiency (equal to ammonia removal) of 70 ± 5.00%. This paper contributes new insight into the formation of moderately halophilic granular sludge and accelerates the application of moderately halophilic granular sludge to treat hypersaline wastewater.

Response of denitrifying anaerobic methane oxidation enrichment to salinity stress: Process and microbiology

Denitrifying anaerobic methane oxidation (DAMO) is a novel biological process which could decrease nitrogen pollution and methane emission simultaneously in wastewater treatment. Salinity as a key environmental factor has important effects on microbial community and activity, however, it remains unclear for DAMO microorganisms. In this study, response of the enrichment of DAMO archaea and bacteria to different salinity was investigated from the aspect of process and microbiology. The results showed that the increasing salinity from 0.14% to 25% evidently deteriorated DAMO process, with the average removal rate of nitrate and methane decreased from 1.91 mg N/(L·d) to 0.07 mg N/(L·d) and 3.22 μmol/d to 0.59 μmol/d, respectively. The observed IC₅₀ value of salinity on the DAMO culture was 1.73%. Further microbial analyses at the gene level suggested that the relative abundance of DAMO archaea in the enrichment decreased to 46%, 39%, 38% and 33% of the initial value. However, DAMO bacteria suffered less impact with the relative abundance maintaining over 75% of the initial value (except 1% salinity). In functional genes of DAMO bacteria, pmoA, decreased gradually from 100% to 86%, 43%, 15% and 2%, while mcrA (DAMO archaea) maintained at 67%-97%. This difference probably indicated DAMO bacteria appeared functional inhibition prior to community inhibition, which was opposite for the DAMO archaea. Results above-mentioned concluded that, though the process of nitrate-dependent anaerobic methane oxidation was driven by the couple of DAMO archaea and bacteria, they individually featured different response to high salinity stress. These findings could be helpful for the application of DAMO-based process in high salinity wastewater treatment, and also the understanding to DAMO microorganisms.

Response of simultaneous sulfide and nitrate removal process on acute toxicity of substrate concentration and salinity: Single toxicity and combined toxicity

Simultaneous sulfide and nitrate removal process has performed excellent to treat nitrogen and sulfur pollutants in wastewater treatment. A high salinity stress poses a great challenge to the treatment of highly saline wastewater containing nitrate and sulfide. In addition, sulfide and nitrates are also toxic for the process, and their high concentration would inhibit the process. Therefore, the current work explores the single acute toxic effect and combined toxic effect of salinity and substrate concentration on the performance of the process from the perspective of toxicology. Considering sulfide and nitrate removal performance as an indicator, the IC₅₀ values of sulfide were 293.20 mg S/L and 572.30 mg S/L, respectively; while those of salinity were 6.14% wt (91.78 mS/cm) and 6.63% wt (98.73 mS/cm), respectively. High substrate concentration or salinity resulted in elemental sulfur generation. The molar ratio of generated elemental sulfur to consumed sulfide(R-Sulfate) was close to 1. The response of nitrate reduction product to the elevating substrate concentration was not obvious, while its response to increasing salinity was on the contrary. With the increasing salinity (1.2% wt to 9.6% wt), molar ratio of generated nitrogen gas to consumed nitrate (R-Nitrogen gas) increased from 0.58 to 1, while molar ratio of generated nitrite to consumed nitrate (R-Nitrite) decreased from 0.43 to 0. Factorial analysis test revealed that the combined acute toxicity of substrate and salinity on sulfide oxidization and nitrate reduction were both antagonistic effects.

Multi-Agent Evolutionary Game in the Recycling Utilization of Sulfate-Rich Wastewater

Current industrial development has led to an increase in sulfate-rich industrial sewage, threatening industrial ecology and the environment. Incorrectly treating high-concentration sulfate wastewater can cause serious environmental problems and even harm human health. Water with high sulfate levels can be treated as a resource and treated harmlessly to meet the needs of the circular economy. Today, governments worldwide are working hard to encourage the safe disposal and reuse of industrial salt-rich wastewater by recycling sulfate-rich wastewater (SRW) resources. However, the conflict of interests between the SRW production department, the SRW recycling department, and the governments often make it challenging to effectively manage sulfate-rich wastewater resources. This study aims to use the mechanism of evolutionary game theory (EGT) to conduct theoretical modelling and simulation analysis on the interaction of the behaviour of the above three participants. This paper focuses on the impact of government intervention and the ecological behaviour of wastewater producers on the behavioural decisions of recyclers. The results suggest that the government should play a leading role in developing the SRW resource recovery industry. SRW producers protect the environment in the mature stage, and recyclers actively collect and recover compliant sulfate wastewater resources. Governments should gradually deregulate and eventually withdraw from the market. Qualified recyclers and environmentally friendly wastewater producers can benefit from a mature SRW resources recovery industry.

Can anammox process be adopted for treating wastewater with high salinity exposure risk?

Anammox was a promising technology for nitrogen removal, and has been applied for treating many kinds of nitrogenous wastewaters. Considering the risk in high salinity of the municipal sewage in coastal city, the feasibility of Anammox process for treating low ammonia wastewater (around 50 mg L^-1) with increasing salinity was investigated in this study. The results showed that the salinity in low concentrations (1-5 g L^-1) had slight impact on the nitrogen removal and activity of Anammox bacteria but significantly improved its growth. The moderate salinity (10-40 g L^-1) decreased the specific Anammox activity (SAA) to 8.11 from the initial 13.15 mg N g^-1 SS h^-1, but increased the abundance to 52.3% from 30.1% (Candidatus Kuenenia). High salinity (50-60 g L^-1) performed severe inhibition on activity and abundance both, with the SAA decreased to 0 and abundance to 11.9%. The self-recovery performance was unsatisfactory when salinity was unavailable. A quadratic curve between the SAA and salinity concentration was fitted, and the IC₅₀ was calculated as 42.1 g L^-1 (NaCl). Anammox process could be directly adopted for treating low ammonia sewage with low salinity, whereas activity enhancement or adaption improvement should be pre-presented for treating sewage with moderate or high salinity.

Effect of low salinity on nitrogen removal from municipal wastewater via a double-anammox process coupled with nitritation and denitratation: Performance and microbial structure

Saline wastewater present in municipal pipe networks poses challenges to biological nitrogen removal due to its inhibition on microorganisms. This study focuses on the effects of low salinity (0.0%, 0.4%, 0.7% and 1.0%) on a system featuring a combination of nitritation/anammox in oxic stage and denitratation/anammox in anoxic stage (double-anammox) in a step-feed SBR for municipal wastewater over a period of 130 days. The results showed that a maximum nitrogen removal efficiency of 81.2% was achieved at a salinity of 1.0% with anammox contribution of 76.5%. Analysis of anammox contribution and sludge activities discovered that low salinity promoted both nitritation and denitratation, further enhancing the coupling with anammox. Further, microbial analysis confirmed that Ca. Brocadia was enriched on biofilms from 0.21% to 0.51% and Nitrosomonas was enriched in flocs from 0.50% to 1.04%. Overall, the double-anammox process appears to be a promising method for the treatment of saline wastewater.

An ultrasound/O3 and UV/O3 process for atrazine manufacturing wastewater treatment: a multiple scale experimental study

An ultraviolet (UV) and ultrasound (US) enhanced ozonation method were developed to investigate their efficiency on the removal of atrazine and chemical oxygen demand (COD) in authentic atrazine manufacturing wastewater. The bench-scale tests suggested a positive effect of UV and US on the degradation of atrazine within a limited energy range. The pilot-scale flow-through system was further tested by using response surface methodology. The results showed that O₃ and its interaction with UV promoted the degradation of both COD and atrazine while its interaction with US inhibited the removal of COD but promoted the removal of atrazine. The optimal removal rate of atrazine (96.9%) was achieved in the condition of 6.86 W/L UV, 1.96 g/L·h O₃ and 294 W/L US. Chloride ions hindered the atrazine degradation, but the generated free chlorine radicals were still able to react with atrazine. In terms of energy-effectiveness, the configuration of 14.7 W/L UV and 1.96 g/L·h O₃ is the best option, which have the electrical energy per order of 181.6 kWh/m³ for atrazine and 0.13 kWh/g COD. These method and findings could be helpful in the development of energy-efficient advanced oxidation processes in treating wastewater with high salinity and COD loadings.

Techno-Economic Analysis on an Industrial-Scale Production System of Polyhydroxyalkanoates (PHA) from Cheese By-Products by Halophiles

Polyhydroxyalkanoates (PHA) are a family of biodegradable plastics used as an ecofriendly alternative for conventional plastics in various applications. In this study, an industrial-scale PHA production system was designed and analyzed for the material flows and economics with the use of SuperPro Designer. Haloferax mediterranei was utilized to produce poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV). Byproduct streams from a local cheese plant, with an input of 168.7 metric ton/day (MT/day) lactose, were used as the feedstock. Three scenarios with different processes for the treatments of used enzyme and spent medium were investigated and the major factors that influence the overall economics were identified. The simulated system produces 9700 MT/year PHBV with a yield of 0.2 g PHBV/g lactose and an overall process efficiency of 87%. The breakeven price was found to be more sensitive to the lactose price than enzyme price. The scenario with enzyme reuse and spent medium recycling achieved the lowest breakeven price among others, which can be less than 4 $/kg PHA based on the delactosed permeate (DLP) unit price. The study suggests utilizing dairy derived feedstocks has the potential to make PHA competitive in the bioplastic market, which could be beneficial to both dairy and bioplastic industries.

Differences in the Effects of Calcium and Magnesium Ions on the Anammox Granular Properties to Alleviate Salinity Stress

Divalent cations were known to alleviate salinity stress on anammox bacteria. Understanding the mechanism of reducing the salinity stress on anammox granules is essential for the application of the anammox process for saline wastewater treatment. In this study, the effect of Ca2+ and Mg2+ augmentation on the recovery of the activity of freshwater anammox granules affected by salinity stress was evaluated. At the condition of a salinity stress of 5 g NaCl/L, the specific anammox activity (SAA) of the granule decreased to 50% of that of the SAA without NaCl treatment. Augmentation of Ca2+ at the optimum concentration of 200 mg/L increased the SAA up to 78% of the original activity, while the augmentation of Mg2+ at the optimum concentration of 70 mg/L increased the SAA up to 71%. EPS production in the granules was increased by the augmentation of divalent cations compared with the granules affected by salinity stress. In the soluble EPS, the ratio of protein to polysaccharides was higher in the granules augmented by Ca2+ than with Mg2+, and the functional groups of the EPS differed from each other. The amount of Na+ sequestered in the soluble EPS was increased by the augmentation of divalent cations, which seems to contribute to the alleviation of salinity stress. Ca. Kuenenia-like anammox bacteria, which were known to be salinity stress-tolerant, were predominant in the granules and there was no significant difference in the microbial community of the granules by the salinity stress treatment. Our results suggest that the alleviation effect of the divalent cations on the salinity stress on the anammox granules might be associated with the increased production of different EPS rather than in changes to the anammox bacteria.

Valorization of high-salinity effluents for CO2 fixation and hypochlorite generation

In this work, it is evaluated the fixation of carbon dioxide using the alkali generated in the chloralkaline process, as a new way to face the treatment of highly saline wastewater, in which it is aimed not to separate the wastewater into concentrated and diluted streams but to recover value-added products (VAPs) while contributing to minimize the carbon fingerprint of other processes. The electrolytic process is combined with a reactive absorption and with a crystallization, demonstrating the formation of pure nahcolite, hypochlorite (or chlorine) and hydrogen from the waste. Carbon dioxide is captured with a current efficiency over 90% and the energy required is around 0.65 kWh kg^-1, which is very promising from the view point of sustainability, considering that the system can be easily powered with green energies.

Current available treatment technologies for saline wastewater and land-based treatment as an emerging environment-friendly technology: A review

Different industrial activities such as agro-food processing and manufacturing, leather manufacturing, and paper and pulp production generate highly saline wastewater. Direct discharge of saline wastewater has resulted in pollution of waterbodies by very high magnitudes. Consequently, an enormous number of pollutants such as heavy metals, salts, and organic matter are also released into the environment threatening the survival of human and biota. Saline wastewater also has significant effects on survival of plants, agricultural activities, and groundwater systems. Several treatments and disposal technologies are available for saline wastewater, but the selection of the most appropriate treatment and disposal technology still remains a major challenge with respect to the economic or technical constraints. Considering the sustainable management of saline wastewater, the present review is an attempt to compile the existing and emerging technologies for the treatment of saline wastewater. Among all the individual and hybrid technologies, land-based treatment systems are proven to be the most efficient technologies considering the energy demands, economic, and treatment efficiencies. Likewise, new and sustainable technologies are the need of hour integrating both the treatment and management and the resource recovery factors along with the ultimate goal of the protection in terms of human health and environmental aspect. PRACTITIONER POINTS: Physico-chemical treatment technologies for saline wastewater. Combined/Hybrid technologies for the treatment of saline wastewater. Land-based treatments as the environment friendly and sustainable method for saline wastewater treatment and disposal. Role of phytoremediation in land-based treatment.

Investigation of organic impurity and its occurrence in industrial waste salt produced by physicochemical process

Industrial waste salt is classified as hazardous waste to the environment. The organic impurity and its occurrence in industrial waste salt affect the salt resource utilization. In this paper, composition quantitative analysis, XRD, TG-DSC, SEM/FIB-SEM coupled with EDS, FTIR, XPS and GC-Ms were chosen to investigate the organic impurity and its occurrence in industrial waste salt. The organic impurities owe small proportion (1.77%) in the specimen and exhibit weak thermal stability within the temperature of 600°C. A clear definition of organic impurity, including 11 kinds of organic compounds, including aldehyde, benzene and its derivatives etc., were detected in the industrial waste salt. These organic impurities, owing (C-O/C-O-C, C-OH/C = O, C–C/CH_x/C = C etc.)-containing function group substance, are mainly distributed both on the surface and inside of the salt particles. Meanwhile, the organic substance may combine with metal cations (Ni²⁺, Mg²⁺, Cu²⁺ etc.) through functional groups, such as hydroxide, carbonyl etc., which increases its stability in the industrial waste salt. These findings provide comprehensive information for the resource utilization of industrial waste salt from chemical industry etc.

Extremophilic Exopolysaccharides: Biotechnologies and Wastewater Remediation

Various microorganisms thrive under extreme environments, like hot springs, hydrothermal vents, deep marine ecosystems, hyperacid lakes, acid mine drainage, high UV exposure, and more. To survive against the deleterious effect of these extreme circumstances, they form a network of biofilm where exopolysaccharides (EPSs) comprise a substantial part. The EPSs are often polyanionic due to different functional groups in their structural backbone, including uronic acids, sulfated units, and phosphate groups. Altogether, these chemical groups provide EPSs with a negative charge allowing them to (a) act as ligands toward dissolved cations as well as trace, and toxic metals; (b) be tolerant to the presence of salts, surfactants, and alpha-hydroxyl acids; and (c) interface the solubilization of hydrocarbons. Owing to their unique structural and functional characteristics, EPSs are anticipated to be utilized industrially to remediation of metals, crude oil, and hydrocarbons from contaminated wastewaters, mines, and oil spills. The biotechnological advantages of extremophilic EPSs are more diverse than traditional biopolymers. The present review aims at discussing the mechanisms and strategies for using EPSs from extremophiles in industries and environment bioremediation. Additionally, the potential of EPSs as fascinating biomaterials to mediate biogenic nanoparticles synthesis and treat multicomponent water contaminants is discussed.

Biotechnological Aspects of Salt-Tolerant Xylanases: A Review

β-1,4-Xylan is the main component of hemicelluloses in land plant cell walls, whereas β-1,3-xylan is widely found in seaweed cell walls. Complete hydrolysis of xylan requires a series of synergistically acting xylanases. High-saline environments, such as saline-alkali lands and oceans, frequently occur in nature and are also involved in a broad range of various industrial processes. Thus, salt-tolerant xylanases may contribute to high-salt and marine food processing, aquatic feed production, industrial wastewater treatment, saline-alkali soil improvement, and global carbon cycle, with great commercial and environmental benefits. This review mainly introduces the definition, sources, classification, biochemical and molecular characteristics, adaptation mechanisms, and biotechnological applications of salt-tolerant xylanases. The scope of development for salt-tolerant xylanases is also discussed. It is anticipated that this review would serve as a reference for further development and utilization of salt-tolerant xylanases and other salt-tolerant enzymes.

The application of UV/O3 process on ciprofloxacin wastewater containing high salinity: Performance and its degradation mechanism

The increasing discharge of high-salinity organic wastewater has drawn much concern. This work investigated the degradation and mineralization of ciprofloxacin (CIP) in high-salinity wastewater by ozonation coupled with ultraviolet irradiation (UV). After coupling with UV, the removal efficiency of CIP was increased insignificantly (maximum 5.0%), while the dissolved organic carbon (DOC) removal in CIP wastewater (CW) was enhanced dramatically to 91.4% as compared with independent O₃ (37.5%). The reactive oxygen species (ROS) were identified as singlet oxygen (¹O₂) and superoxide anion radical (O₂^-•)·through electron paramagnetic resonance (EPR) and quenching experiments, among which ¹O₂ predominated in the UV/O₃ process. The existence of salt (Na₂SO₄ or NaCl) accelerated the mass transfer of O₃ at the gas-liquid interface, thus CIP removal was promoted in UV/O₃/SO₄^2- system. However, excessive Cl^- inhibited the removal efficiency of DOC in CW owing to its consumption of O₃. CIP degradation decreased as pH increased in non-salinity and UV/O₃/SO₄^2- system, which proved the direct reaction occurred between CIP and O₃. On the contrary, the O₃ mass transfer increased with increasing pH, hence the elimination of DOC in CW was promoted in UV/O₃/Cl^- system. Volatile organic compounds (VOCs) were detected from tail gas, but the toxicity estimation indicated the toxicity of products was similar or less than that of CIP. Overall, this work is meaningful for the practical application of UV/O₃ process in the high-salinity industry.

Sodium Reduction in Traditional Fermented Foods: Challenges, Strategies, and Perspectives

Sodium salt is a pivotal ingredient in traditional fermented foods, but its excessive consumption adversely affects human health, product quality, and production efficiency. Therefore, reducing sodium salt content in traditional fermented foods and developing low-sodium fermented foods have attracted increasing attention. Given the essential role of sodium salt in the safety and quality of fermented foods, appropriate approaches should be applied in the production of low-sodium fermented foods. In this review, the challenges of sodium reduction in traditional fermented foods are presented, including the possible growth of pathogenic bacteria, the formation of hazardous chemicals, flavor deficiency, and texture deterioration. Physical, chemical, and biological strategies are also discussed. This review provides references for improving the quality and safety of low-sodium fermented foods.

Salinity is the major driver of the global eukaryotic community structure in fish-canning wastewater treatment plants

Fish-canning wastewater is characterized frequently by a high content of salt (NaCl), making its treatment particularly difficult; however, the knowledge of the effect of NaCl on eukaryotic communities is very limited. In the present study, the global diversity of eukaryotes in activated sludges (AS) from 4 different wastewater treatment plants (WWTPs) treating fish-canning effluents varying in salinity (0.47, 1.36, 1.72 and 12.76 g NaCl/L) was determined by sequencing partial 18S rRNA genes using Illumina MiSeq. A greater diversity than previously reported was observed in the AS community, which comprised 37 and 330 phylum-like and genera-like groups, respectively. In this sense, the more abundant genus-like groups (average relative abundance (RA) > 5%) were Adineta (6.80%), Lecane (16.80%), Dictyostelium (7.36%), Unclassified_Fungi7 (6.94%), Procryptobia (5.13) and Oocystis (5.07%). The eukaryotic communities shared a common core of 25 phylum-like clades (95% of total sequences); therefore, a narrow selection of the eukaryotic populations was found, despite the differences in the abiotic characteristics of fish-canning effluents and reactor operational conditions inflicted. The differences in NaCl concentration were the main factor that influenced the structure of the eukaryotic community, modulating the RAs of the different phylum-like clades of the common core. Higher levels of salt increased the RAs of Ascomycota, Chlorophyta, Choanoflagellata, Cryptophyta, Mollusca, Nematoda, Other Protists and Unclassified Fungi. Among the different eukaryotic genera here found, the RA of Oocystis (Chlorophyta) was intimately correlated to increasing NaCl concentrations and it is proposed as a bioindicator of the global eukaryotic community of fish-canning WWTPs.

The Survival of Haloferax mediterranei under Stressful Conditions

Haloarchaea can survive and thrive under exposure to a wide range of extreme environmental factors, which represents a potential interest to biotechnology. Growth responses to different stressful conditions were examined in the haloarchaeon Haloferax mediterranei R4. It has been demonstrated that this halophilic archaeon is able to grow between 10 and 32.5% (w/v) of sea water, at 32–52 °C, although it is expected to grow in temperatures lower than 32 °C, and between 5.75 and 8.75 of pH. Moreover, it can also grow under high metal concentrations (nickel, lithium, cobalt, arsenic), which are toxic to most living beings, making it a promising candidate for future biotechnological purposes and industrial applications. Inductively Coupled Plasma Mass Spectrometry (ICP-MS) analysis quantified the intracellular ion concentrations of these four metals in Hfx. mediterranei, concluding that this haloarchaeon can accumulate Li⁺, Co²⁺, As⁵⁺, and Ni²⁺ within the cell. This paper is the first report on Hfx. mediterranei in which multiple stress conditions have been studied to explore the mechanism of stress resistance. It constitutes the most detailed study in Haloarchaea, and, as a consequence, new biotechnological and industrial applications have emerged.

Study on the osmoregulation of "Halomonas socia" NY-011 and the degradation of organic pollutants in the saline environment

"Halomonas socia" NY-011, a new species of moderately halophilic bacteria isolated and identified in our laboratory, can grow in high concentrations of salt ranging from 0.5 to 25%. In this study, the whole genome of NY-011 was sequenced and a detailed analysis of the genomic features was provided. Especially, a series of genes related to salt tolerance and involved in xenobiotics biodegradation were annotated by COG, GO and KEGG analyses. Subsequently, RNA-Seq-based transcriptome analysis was applied to explore the osmotic regulation of NY-011 subjected to high salt stress for different times (0 h, 1 h, 3 h, 6 h, 11 h, 15 h). And we found that the genes related to osmoregulation including excluding Na⁺ and accumulating K⁺ as well as the synthesis of compatible solutes (alanine, glutamate, ectoine, hydroxyectoine and glycine betaine) were up-regulated, while the genes involved in the degradation of organic compounds were basically down-regulated during the whole process. Specifically, the expression trend of genes related to osmoregulation increased firstly then dropped, which was almost opposite to that of degrading organic pollutants genes. With the prolongation of osmotic up-shock, NY-011 survived and gradually adapted to osmotic stress, the above-mentioned two classes of genes slowly returned to normal expression level. Then, the scanning electron microscope (SEM) and transmission electron microscope (TEM) were also utilized to observe morphological properties of NY-011 under hypersaline stress, and our findings showed that the cell length of NY-011 became longer under osmotic stress, at the same time, polyhydroxyalkanoates (PHAs) were synthesized in the cells. Besides, physiological experiments confirmed that NY-011 could degrade organic compounds in a high salt environment. These data not only provide valuable insights into the mechanism of osmotic regulation of NY-011; but also make it possible for NY-011 to be exploited for biotechnological applications such as degrading organic pollutants in a hypersaline environment.

In-Situ Combination of Bipolar Membrane Electrodialysis with Monovalent Selective Anion-Exchange Membrane for the Valorization of Mixed Salts into Relatively High-Purity Monoprotic and Diprotic Acids

The crystalized mixed salts from the zero liquid discharge process are a hazardous threat to the environment. In this study, we developed a novel electrodialysis (SBMED) method by assembling the monovalent selective anion-exchange membrane (MSAEM) into the bipolar membrane electrodialysis (BMED) stack. By taking the advantages of water splitting in the bipolar membrane and high perm-selectivity of MSAEM for the Cl- ions against the SO42- ions, this combination allows the concurrent separation of Cl-/SO42- and conversion of mixed salts into relatively high-purity monoprotic and diprotic acids. The current density has a significant impact on the acid purity. Both the monoprotic and diprotic acid purities were higher than 80% at a low current density of 10 mA/cm2. The purities of the monoprotic acids decreased with an increase in the current density, indicating that the perm-selectivity of MSAEM decreases with increasing current density. An increase in the ratio of monovalent to divalent anions in the feed was beneficial to increase the purity of monoprotic acids. High-purity monoprotic acids in the range of 93.9-96.1% were obtained using this novel SBMED stack for treating simulated seawater. Therefore, it is feasible for SBMED to valorize the mixed salts into relatively high-purity monoprotic and diprotic acids in one step.

High-strength wastewater treatment using microbial biofilm reactor: a critical review

Biofilm reactors retain microbial cells in the form of biofilm which is attached to free moving or fixed carrying materials, thus providing a high active biomass concentration and automatic liquid and solid separation. Nowadays, microbial biofilm reactors have been widely used in high-strength wastewater treatment where very high pollutant removal efficiency is required, which usually requires excessive space and aeration energy for conventional activated sludge-based treatment. This paper provides an overview of microbial biofilm reactors developed over the last half-century, including moving bed biofilm reactor (MBBR), trickling filter (TF) reactor, rotating biological contactor (RBC), membrane biofilm reactor (MBfR), passive aeration simultaneous nitrification and denitrification (PASND) biofilm reactor, for their applications in high-strength wastewater treatment of not only removing carbon, nitrogen, sulphur but also a variety of oxidized contaminants including perchlorate and bromate. Despite the advance of biofilm reactor that exhibits high resistance to excessive pollutants loading, its drawbacks both from engineering and microbiological point of view are reviewed. The future prospects of biofilm reactor are also discussed in this review paper.