Activated carbon adsorptive removal of azo dye and peroxydisulfate regeneration: from a batch study to continuous column operation

Preparation of graphene oxide-doped silica aerogel using supercritical method for efficient removal of emerging pollutants from wastewater

Emerging pollutants and a large volume of unused dyes from the textile industry have been contaminating water bodies. This work introduces a scalable approach to purifying water by the adsorption of Acid green 25 (AG), Crystal Violet (CV), and Sulfamethoxazole (SMA) from an aqueous solution by graphene oxide (GO) doped modified silica aerogel (GO-SA) with supercritical fluid deposition (SFD) method. Characterization of GO-SA using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), high-resolution scanning electron microscopy (HR-SEM), thermogravimetric analysis (TGA), and Brunauer-Emmett-Teller (BET) adsorption isotherms revealed the improvement in the adsorbent surface area, and its textural properties. The high removal percentages observed in most of the experimental runs provide evidence of the excellent performance of the adsorbent towards the anionic and cationic dyes along with the antibiotic. The adsorption isotherm and kinetics showed that the Langmuir isotherm and pseudo-second-order kinetic models could explain adsorption. The adsorbent holds a higher adsorption capacity for SMA (67.07 mg g-1) than for CV (41.46 mg g-1) and AG (20.56 mg g-1) due to the higher hydrophobicity that interacts with the hydrophobic adsorbent. The GO-SA successfully removed AG, CV, and SMA with removal percentages of 98.23%, 98.71%, and 94.46%, respectively. The parameters were optimized using Central Composite Design (RSM-CCD). The prepared aerogel showed excellent reusability with a removal efficiency of > 85% even after 5 cycles. This study shows the potential of GO-SA adsorbent in textile and other wastewater purification.

Microporous Activated Carbon from Pisum sativum Pods Using Various Activation Methods and Tested for Adsorption of Acid Orange 7 Dye from Water

This work demonstrates the preparation of high-surface-area activated carbon (AC) from Pisum sativum pods using ZnCl2 and KOH as activating agents. The influence of CO2 and N2 gases during the carbonization process on the porosity of AC were studied. The highest specific surface area of AC was estimated at 1300 to 1500 m2/g, which presented characteristics of microporous materials. SEM micrographs revealed that chemical activation using an impregnation reagent ZnCl2 increases the porosity of the AC, which in turn leads to an increase in the surface area, and the SEM image showed that particle size diameter ranged between 48.88 and 69.95 nm. The performance of prepared AC for adsorption of Acid Orange 7 (AO7) dye was tested. The results showed that the adsorption percentage by AC (2.5 g/L) was equal to 94.76% after just 15 min, and the percentage of removal increased to be ~100% after 60 min. The maximum adsorption capacity was 473.93 mg g-1. A Langmuir model (LM) shows the best-fitted equilibrium isotherm, and the kinetic data fitted better to the pseudo-second-order and Film diffusion models. The removal of AO7 dye using AC from Pisum sativum pods was optimized using a response factor model (RSM), and the results were reported.

Systematic evaluation of activated carbon-Fe3O4 composites for removing and degrading emerging organic pollutants

In this study, a comparative activity assessment of several activated carbon (AC) and AC-Fe₃O₄ composites was performed to evaluate their efficiency and versatility as Fenton-like catalysts. Although many studies have demonstrated the advantages of AC-based materials as Fenton-like catalysts, most have been developed using only one oxidant and/or one pollutant. Here, untreated (AC₀) and acid-treated AC (AC_A) iron-oxide composites were synthesized, characterized, and compared in terms of activity to bare AC using several oxidants and pollutants, the activation efficiency of hydrogen peroxide (H₂O₂) and ammonium persulfate ((NH₄)₂S₂O₈), and the subsequent oxidation extent and kinetics of bisphenol-A, atrazine, and carbamazepine by the AC-based materials were studied in depth. The persulfate-based systems showed considerably higher pollutant removal in the presence of the catalysts, despite lower persulfate decomposition rates: atrazine and carbamazepine were partially degraded, mainly through a radical-dependent pathway; the highest removal of atrazine was achieved with the AC_A-iron composite, whereas carbamazepine was best removed by the AC₀-iron composite. In contrast, bisphenol A was completely mineralized, probably via a non-radical pathway, in the presence of all AC-based composites, even at very low persulfate concentrations. Furthermore, bisphenol A removal remained high for several consecutive cycles, with the most efficient removal and stability observed in the presence of AC_A. These findings reveal the high complexity of AC-based systems, with multiple binding sites and degradation pathways unique to each combination of pollutants, catalysts, and oxidants. In general, the composition of the waste stream governs the applicability of these materials. Thus, the structure-function correlations and degradation mechanisms revealed here are crucial for improving sorbent-catalyst design and accelerating the implementation of low-cost remediation and in situ regeneration technologies.

Synthesis and characterization of magnetic biochar adsorbents for the removal of Cr(VI) and Acid orange 7 dye from aqueous solution

In this study, different types of magnetic biochar nanocomposites were synthesized using the co-precipitation method. Two biochar materials, namely, sewage sludge biochar and woodchips biochar, were prepared at two different temperatures, viz., 450 and 700 °C. These biochars were further modified with magnetic nanoparticles (Fe₃O₄). The modified biochar nanocomposites were characterized using field emission-scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), SQUID analysis, X-ray photoelectron spectroscopy (XPS), and Fourier-transform infrared spectroscopy (FTIR). The potential of prepared adsorbents was examined for the removal of hexavalent chromium (Cr(VI)) and Acid orange 7 (AO7) dye from water as a function of various parameters, namely, contact time, pH of solution, amount of adsorbents, and initial concentrations of adsorbates. Various kinetic and isotherm models were tested to discuss and interpret the adsorption mechanisms. The maximum adsorption capacities of modified biochars were found as 80.96 and 110.27 mg g^-1 for Cr(VI) and AO7, respectively. Magnetic biochars showed high pollutant removal efficiency after 5 cycles of adsorption/desorption. The results of this study revealed that the prepared adsorbents can be successfully used for multiple cycles to remove Cr(VI) and AO7 from water. Graphical Abstract.

Surface Modification of Bentonite with Polymer Brushes and Its Application as an Efficient Adsorbent for the Removal of Hazardous Dye Orange I

Poly(2-(dimethylamino)ethyl methacrylate)-grafted bentonite, marked as Bent-PDMAEMA, was designed and prepared by a surface-initiated atom transfer radical polymerization method for the first time in this study. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and thermal gravimetric analysis (TGA) were applied to characterize the structure of Bent-PDMAEMA, which resulted in the successful synthesis of Bent-PDMAEMA. As a cationic adsorbent, the designed Bent-PDMAEMA was used to remove dye Orange I from wastewater. The adsorption property of Bent-PDMAEMA for Orange I dye was investigated under different experimental conditions, such as solution pH, initial dye concentration, contact time and temperature. Under the optimum conditions, the adsorption amount of Bent-PDMAEMA for Orange I dye could reach 700 mg·g-1, indicating the potential application of Bent-PDMAEMA for anionic dyes in the treatment of wastewater. Moreover, the experimental data fitted well with the Langmuir model. The adsorption process obeyed pseudo-second-order kinetic process mechanism.

Application of immobilized ZnO nanoparticles for the photocatalytic regeneration of ultrasound pretreated-granular activated carbon

In this study, the photocatalytic regeneration by ZnO was employed for the regeneration of the granular activated carbon (GAC) which was saturated with the reactive red 43. The ultrasound was applied as a pretreatment step due to the cleanup of the adsorbent surface and providing a higher surface area and adsorption capacity. According to the nitrogen gas adsorption-desorption results, the ultrasound pretreated-GAC had the highest surface area and the total pore volume. The SEM and XRD analyses confirmed the immobilization of ZnO nanoparticles on the GAC. Response surface methodology (RSM) was used to model and optimize the preparation of the granular activated carbon/ZnO nanocomposite. The sonication time, pH, GAC/ZnO ratio, and calcination temperature were used as four effective parameters on nanocomposite preparation. Optimum amounts of pH, GAC/ZnO ratio, calcination temperature, and sonication time were found to be equal to 4, 5, 300 °C, 210 min, respectively; in these conditions, 83.98% of the capacity of the exhausted granular activated carbon was regenerated. ANOVA results, high R², R²-adj values, and also normal and random distribution of residuals showed that application of RSM for the modeling and optimizing the preparation step of GAC/ZnO nanocomposite was successful.

Simultaneous removal of As(V)/Cr(VI) and acid orange 7 (AO7) by nanosized ordered magnetic mesoporous Fe-Ce bimetal oxides: Behavior and mechanism

In this study, nanosized ordered magnetic mesoporous Fe-Ce bimetal oxides (Nanosized-MMIC) with highly well-ordered inner-connected mesostructure were successfully synthesized through the KIT-6 template method. This Nanosized-MMIC displayed excellent adsorption capacities for As(V), Cr(VI) and AO7, and the corresponding calculated maximum adsorption capacities of material were 111.17, 125.28 and 156.52 mg/g, respectively. As(V) and Cr(VI) removal by Nanosized-MMIC were slightly dependent on the ionic strength but highly solution pH-dependent, the coexistent silicate and phosphate ions competed remarkably with both As(V) and Cr(VI) for the adsorption active site. Mechanisms indicated As(V) and Cr(VI) formed inner-sphere complexes on Nanosized-MMIC interface via the electrostatic interaction and surface complexation, while the total organic carbon (TOC) change demonstrated that AO7 could be removed completely and no organic intermediates formed through the adsorption process. In addition, Nanosized-MMIC also possessed superior adsorption performance in As(V)/Cr(VI)-AO7 binary systems, and the reusable and regeneration properties indicated that the obtained nanomaterials could maintain at a comparatively high level after several recycling. Finally, fixed-bed experiments suggested the Nanosized-MMIC was expected to have a promising excellent nano-adsorbent with high application potential for co-existed toxic heavy metals and organic dyes removal in practical wastewater treatment.

Selective adsorption of phenanthrene dissolved in Tween 80 solution using activated carbon derived from walnut shells

In order to remove phenanthrene (PHE) from surfactant solution, activated carbon (AC) was prepared from waste walnut shells and characterized by Brunauer-Emmett-Teller (BET), field-emission scanning electron microscopy (FESEM), Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). For solutions containing PHE and Tween 80, the former was effectively removed and the latter could be economically recovered after adsorption by the prepared AC. The π-π interactions and oxygen containing functional groups of AC play important roles in the PHE adsorption process. The adsorption kinetics process could best be described using the pseudo-second-order model and adsorption isotherm results indicated that the Langmuir model best fitted the data. Adsorption thermodynamic parameters, including enthalpy change, Gibbs free energy change and entropy change were calculated. Under optimal conditions, PHE removal and Tween 80 recovery reached 95% and 90%, respectively. The results suggest that AC provided an efficient alternative for selective adsorption of PHE and recovery of Tween 80 after the soil washing processes. After adsorption AC could be regenerated with ethanol and even if AC were regenerated twice PHE removal reached 80%.

Catalytic degradation of Orange II in aqueous solution using diatomite-supported bimetallic Fe/Ni nanoparticles

A functional diatomite-supported Fe/Ni nanocomposite successfully remediated Orange II contaminant in aqueous solution. The hypothesis was that diatomite-supported Fe/Ni would not only be more effective than Fe/Ni but also require less metallic loading to effect the catalytic reaction. Batch experiments indicate that 99.00% of Orange II was removed using diatomite-supported Fe/Ni, while only 86.64 and 3.59% of Orange II were removed using bimetallic Fe/Ni nanoparticles and diatomite, after 6 h of reaction, respectively. Characterisation by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and scanning electron microscopy (SEM) indicates that the use of diatomite as a support material reduced the aggregation of bimetallic Fe/Ni nanoparticles, thereby resulting in an enhancement in the reactivity. A synergistic mechanism for the removal of Orange II by diatomite-supported Fe/Ni was proposed which involves adsorption, followed by catalytic reduction. This study has demonstrated that diatomite may be a suitable support material for stabilizing and dispersing bimetallic Fe/Ni nanoparticles and the resulting diatomite-supported Fe/Ni composite could be a promising catalyst for the remediation of dye-contaminated wastewater.

A functional diatomite-supported Fe/Ni nanocomposite successfully remediated Orange II contaminant in aqueous solution.

Degradation of Acid Orange 7 using peroxymonosulfate catalyzed by granulated activated carbon and enhanced by electrolysis

Electrochemistry coupled with granulated activated carbon catalysis of peroxymonosulfate (electro/GAC/PMS) as a novel wastewater treatment process was performed for the degradation of Acid Orange 7 (AO7) in aqueous solution. The decolorization of AO7 was compared under different permutations and combinations of electro-oxidation, GAC and PMS. It showed that the electro/GAC/PMS process was the most effective and the decolorization of AO7 followed pseudo-first order kinetics. The surface chemistry of GAC samples was analyzed by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Compared with the fresh samples, π-electron density and hydroxyl group content decreased under the GAC/PMS system, but kept the similar values under the electro/GAC/PMS system. Electron paramagnetic resonance and radical scavenger studies were used to verify the formation of sulfate radicals (SO₄^-) and hydroxyl radicals (OH). The optimized conditions were found to be: current density 8 mA cm^-2; PMS concentration 5 mM; GAC dosage 0.5 g L^-1; and initial pH value 5.0. GAC recycling experiments over 4 runs showed some decrease in reactivity. Overall, the results indicate that 100% color removal was readily achieved and 50.4% of TOC was removed which shows high efficiency of the electro/GAC/PMS process.

Decolorization of Color Index Acid Orange 20 buffer solution using horseradish peroxidase immobilized on modified PAN-beads

In the present work, horseradish peroxidase (HRP) is utilized to be immobilized onto polyacrylonitrile based beads (PAN-beads) for decolorization of Color Index (C. I.) Acid Orange 20 (AO20) in aqueous solution.