Removal of Pb(II) from aqueous solutions by adsorption on magnetic bentonite

Removal of Pb(II) ions from aqueous solutions using natural and HDTMA-modified bentonite and kaolin clays

This work focused on the removal of Pb(II) from aqueous solution using kaolin and bentonite clays modified with hexadecyl trimethyl ammonium bromide (HDTMA). The clays were characterized using a zetasizer, scanning electron microscopy (SEM), powder X-ray diffraction (PXRD), Brunauer-Emmet-Teller (BET), Fourier-transform infrared (FTIR) spectroscopy and thermal gravimetric analysis (TGA). Factors that influence the adsorption of Pb(II) from aqueous solution, namely pH, contact time, adsorbent mass, ionic strength, temperature and initial Pb(II) concentration were investigated. The results show that HDTMA was successfully incorporated into the kaolin and bentonite clay structures. The most favorable parameters for the adsorption of Pb(II) ions onto all adsorbents was pH of 6.0, temperature of 25 °C and adsorbent mass of 200 mg. Adsorption isotherms and kinetic studies showed that the adsorption of Pb(II) onto kaolin, bentonite and organobentonite clays followed the Langmuir isotherm and pseudo-first order kinetic model, while the adsorption onto organobentonite was better explained by the Freundlich isotherm and pseudo-second order kinetic model. Maximum monolayer adsorption capacity of organobentonite, calculated from the Langmuir model was 18.75 mg/g, which is higher than that obtained for the unmodified bentonite (14.71 mg/g); while for organokaolin it was 2.26 mg/g, which is less than that of the unmodified kaolin (4.19 mg/g). Thermodynamic studies showed that the reactions were exothermic and unfavoured at high temperatures. The adsorbents also showed good removal efficiency for up to four regeneration cycles.

Synthesis of ZIF-8/chitosan composites for Cu2+ removal from water

In this work, a kind of novel Chitosan (Cs)-doped zeolite imidazole framework (ZIF-8@Cs) with a larger surface area and a smaller pore size was synthesised via a facial solvothermal approach and applied to remove Cu2+ from mine wastewater. Compared to nondoped ZIF-8, ZIF-8@Cs exhibited a stronger adsorption performance and removal efficiency. The reason was that ZIF-8@Cs doped by the Cs could suppress the aggregation and increase the monodispersity of ZIF-8. Using the high-performance ZIF-8@Cs, as a novel adsorbent, was successfully developed for the efficient removal of Cu2+ from mine wastewater. Various parameters, such as contact time, initial Cu2+ concentration, adsorbent dosage, and pH, were investigated. The results showed that a removal efficiency of 85% was obtained at 4 h contact time for a Cu2+ concentration of 30 mg/L at the optimum pH of 6.0. Equilibrium data were analysed using different isothermal models and kinetic models, analytic results indicated that the capture of Cu2+ by ZIF-8@Cs could favourably comply with the pseudo-first-order kinetic model and Langmuir isotherm model. The single-layer adsorption of Cu2+ on ZIF-8@Cs was dominated by diffusional mass transfer. Additionally, the results of the thermodynamic analysis indicated that the adsorption of Cu2+ by ZIF-8/Cs was a spontaneous, exothermic, and ordered process. Overall, the results reported herein indicated that ZIF-8/Cs with high adsorption efficiency are very attractive and imply a potential practical application for the removal of potentially toxic elements in wastewater.

Recent advances of application of bentonite-based composites in the environmental remediation

Bentonite-based composites have been widely utilized in the removal of various pollutants due to low cost, environmentally friendly, ease-to-operate, whereas the recent advances concerning the application of bentonite-based composites in environmental remediation were not available. Herein, the modification (i.e., acid/alkaline washing, thermal treatment and hybrids) of bentonite was firstly reviewed; Then the recent advances of adsorption of environmental concomitants (e.g., organic (dyes, microplastics, phenolic and other organics) and inorganic pollutants (heavy metals, radionuclides and other inorganic pollutants)) on various bentonite-based composites were summarized in details. Meanwhile, the effect of environmental factors and interaction mechanism between bentonite-based composites and contaminants were also investigated. Finally, the conclusions and prospective of bentonite-based composites in the environmental remediation were proposed. It is demonstrated that various bentonite-based composites exhibited the high adsorption/degradation capacity towards environmental pollutants under the specific conditions. The interaction mechanism involved the mineralization, physical/chemical adsorption, co-precipitation and complexation. This review highlights the effect of different functionalization of bentonite-based composites on their adsorption capacity and interaction mechanism, which is expected to be helpful to environmental scientists for applying bentonite-based composites into practical environmental remediation.

Polypyrrole-decorated bentonite magnetic nanocomposite: A green approach for adsorption of anionic methyl orange and cationic crystal violet dyes from contaminated water

In the presented study, a novel polypyrrole-decorated bentonite magnetic nanocomposite (MBnPPy) was synthesized for efficient removal of both anionic methyl orange (MO) and cationic crystal violet (CV) dyes from contaminated water. The synthesis of this novel adsorbent involved a two-step process: the magnetization of bentonite followed by its modification through in-situ chemical polymerization. The adsorbent was characterized by SEM/EDX, TEM/SAED, BET, TGA/DTA-DTG, FTIR, VSM, and XRD studies. The investigation of the adsorption properties of MBnPPy was focused on optimizing various parameters, such as dye concentration, medium pH, dosage, contact time, and temperature. The optimal conditions were established as follows: dye concentration of Co (CV/MO) at 100 mg/L, MBnPPy dosage at 2.0 g/L, equilibrium time set at 105 min for MO and 120 min for CV, medium pH adjusted to 5.0 for MO dye and 8.0 for CV dye, and a constant temperature of 303.15 K. The different kinetic and isotherm models were applied to fit the experimental results, and it was observed that the Pseudo-2nd-order kinetics and Langmuir adsorption isotherm were the best-fitted models. The maximal monolayer adsorption capacities of the adsorbent were found to be 78.74 mg/g and 98.04 mg/g (at 303.15 K) for CV and MO, respectively. The adsorption process for both dyes was exothermic and spontaneous. Furthermore, a reasonably good regeneration ability of MBnPPy (>83.45%/82.65% for CV/MO) was noted for up to 5 adsorption-desorption cycles with little degradation. The advantages of facile synthesis, cost-effectiveness, non-toxicity, strong adsorption capabilities for both anionic and cationic dyes, and easy separability with an external magnetic field make MBnPPy novel.

Cellulose nanocrystals intercalated clay biocomposite for rapid Cr(VI) removal

The application of bentonite (Bt) as an adsorbent for heavy metals has been limited due to its hydrophobicity and insufficient surface area. Herein, we present cellulose nanocrystal (CNC) modified Bt composite (CNC@Bt) with enhanced efficiency for Cr(VI) removal. CNC@Bt exhibited an increased specific surface area and a porous structure, while maintaining the original crystal structure of Bt. This was achieved through a synergistic function of ion exchange, hydrogen bonding, electrostatic interactions, and steric hindrance. The adsorption of Cr(VI) by CNC@Bt followed the pseudo-second-order kinetic and Langmuir isotherm adsorption model. Moreover, the process was endothermic and spontaneous. At an initial Cr(VI) concentration of 20 mg/L and pH = 4.0, 10 g/L CNC@Bt achieved a removal rate of 92.7%, and the adsorption capacity was 1.85 mg/g, significantly higher than bare Bt (37.9% and 0.76 mg/g). The removal efficiency remained consistently above 80% over a wide pH range, indicating the potential practical applicability of CNC@Bt. With its fast adsorption rate, pH adaptability, and stable performance, CNC@Bt presents promising prospects for the rapid treatment of Cr-contaminated wastewater.

Ball milling synthesis of Fe3O4 nanoparticles-functionalized porous boron nitride with enhanced cationic dye removal performance

Enhancement of the adsorption performance and recyclability of adsorbents is a crucial aspect of water treatment. Herein, we used one-dimensional porous boron nitride (PBN) as a carrier to load Fe3O4 nanoparticles for the preparation of Fe3O4 nanoparticles-functionalized porous boron nitride (Fe3O4/PBN) via a ball milling method. The high-energy ball milling promoted the creation of a negatively charged PBN surface and facilitated the uniform distribution of Fe3O4 nanoparticles on the surface of PBN. The adsorption performance of Fe3O4/PBN toward cationic dyes could be significantly improved while no enhancement was observed for anionic dyes. The great adsorption performance of Fe3O4/PBN is due to its surface functional groups and surface defects formed in the ball milling process. Moreover, the strong interaction force between Fe3O4/PBN and cationic dyes promotes rapid initial adsorption due to their negatively charged surface. Magnetic measurements demonstrated that Fe3O4/PBN is superparamagnetic. The composites with low loadings of Fe3O4 nanoparticles could be quickly separated from the aqueous solution under a low applied magnetic field, improving their recyclability. This work highlights the role of ball milling in improving the adsorption performance of Fe3O4/PBN and greatly promotes the practical application of Fe3O4/PBN in the field of environmental purification.

Investigation on Applying Biodegradable Material for Removal of Various Substances (Fluorides, Nitrates and Lead) from Water

Sapropel was used as a biodegradable material for water treatment. Sapropel is a sedimentary layer of a mix of organic and inorganic substances accumulated in the bottoms of lakes for thousands of years. It is a jelly-like homogeneous mass and has properties of sorption. Sapropel is used as a biosorbent and an environment-friendly fertiliser, and it is used in building materials and in the beauty industry as well. In water, there are abundant various solutes that may cause a risk to human health. Such substances include fluorides, nitrates and lead in different sources of water. The goal of this investigation is to explore and compare the efficiencies of removal of different pollutants (fluorides, nitrates and lead) from aqueous solutions upon using sapropel as a sorbent. In this research, various doses of sapropel (0.1, 0.5, 1, 5, 10, 20, 50, 100 and 200 g/L) and various mixing times (15, 30, 60, 90 and 120 min) were used for removal of fluorides, nitrates and lead from aqueous solutions. It was found that the maximum efficiency (up to 98.57%) of lead removal from aqueous solutions by sapropel was achieved when the minimum doses of it (0.1 and 0.5 g/L) were used. The most efficient removal of fluorides (64.67%) was achieved by using 200 g/L of sapropel and mixing for 120 min. However, sapropel does not adsorb nitrates from aqueous solutions.

Modeling, optimization and efficient use of MMT K10 nanoclay for Pb (II) removal using RSM, ANN and GA

Regarding the long-term toxic effects of Pb (II) ions on human health and its bioaccumulation property, taking measures for its reduction in the environment is necessary. The MMT-K₁₀ (montmorillonite-k₁₀) nanoclay was characterized by XRD, XRF, BET, FESEM, and FTIR. The effects of pH, initial concentrations, reaction time, and adsorbent dosage were studied. The experimental design study was carried out with RSM-BBD method. Results prediction and optimization were investigated with RSM and artificial neural network (ANN)-genetic algorithm (GA) respectively. The RSM results showed that the experimental data followed the quadratic model with the highest regression coefficient value (R² = 0.9903) and insignificant lack of fit (0.2426) showing the validity of the Quadratic model. The optimal adsorption conditions were obtained at pH 5.44, adsorbent = 0.98 g/l, concentration of Pb (II) ions = 25 mg/L, and reaction time = 68 min. Similar optimization results were observed by RSM and artificial neural network-genetic algorithm methods. The experimental data revealed that the process followed the Langmuir isotherm and the maximum adsorption capacity was 40.86 mg/g. Besides, the kinetic data indicated that the results fitted with the pseudo-second-order model. Hence, the MMT-K₁₀ nanoclay can be a suitable adsorbent due to having a natural source, simple and inexpensive preparation, and high adsorption capacity.

Synthesis of Electrospun Polyvinyl Butyral/Bentonite Nanofiber Film for Cationic Dye Removal

The textile industry is a common and relevant sector worldwide that generates significant environmental pollution via the discharge of dye-containing wastewater. In this direction, the electrospinning technology can be used to produce adsorbing nanofibers for the treatment of wastewater polluted by dyes and other toxic compounds. The nanofibers obtained by this technology are light and thin, thus providing several advantages (e.g., high surface area) to improve the efficacy of adsorption processes. In this direction, this study reports the preparation of nanofibers from polyvinyl butyral (PVB) and bentonite via electrospinning. This study also reports PVB/bentonite nanofiber mat and its application in adsorbing the cationic dye (methylene blue) from an aqueous solution. The morphology and water contact angles of these nanofibers were analyzed. Results showed that the maximum dye adsorption of these nanofibers was 66.63 mg/g along with 32% removal at pH 9 and 27 ± 2°C. The dye adsorption on these nanofibers was exothermic and pH-dependent, with the best adsorption capacities obtained under alkaline conditions. The adsorption mechanism of this dye molecule on these PVB/bentonite nanofiber mats was associated with van der Waals forces, hydrogen bonding, and electrostatic interactions. This novel composite is an interesting material with improved properties that can be applied to the removal of cationic dyes from wastewater.

Novel GO/Fe-Mn hybrid for the adsorptive removal of Pb(II) ions from aqueous solution and the spent adsorbent disposability in cement mix: compressive properties and leachability study for circular economy benefits

GO/Fe-Mn hybrids were prepared by a single-pot chemical precipitation method and were characterized using FTIR, XRD, Raman, zeta potential, and FESEM, which confirmed the impregnation of Fe/Mn onto GO sheets. The synthesized hybrids were successively applied in removing the Pb(II) ions from aqueous solution and later utilizing the spent adsorbent to increase the properties of cement. The adsorption capability of the synthesized hybrid was seen in a set of batch studies to find out that about 15 min of contact time was required to remove 99% of the contaminant at a pH of 5 ± 0.2 and a dose of 0.83 g/L. The mechanism of the adsorption process for the synthesized hybrid was well described by Elovich kinetic model with an R² of 0.99 and Langmuir isotherm model, also with an R² of 0.99. The desorption studies conducted using 0.1 M HCl solution showed significant stability of the hybrid with a drop of 12% in the removal efficiency of Pb after up to five adsorption-desorption cycles. This points to an efficient adsorbent having potential for economical use. Later, the spent adsorbent was mixed with cement at ratios of 0.05%, 0.1%, and 0.5%, and compressive strength tests were performed, which showed an increase in the strength by 7.62%, 16.11%, and 26.82% at 28 days of curing time. The TCLP and SPLP tests performed on the hybrid and cement-spent adsorbent mix showed all the leaching parameters were well within the permissible limits. This development shows the potential for the use of spent adsorbent in a circular economy model.

Synthesis and Micromechanistic Studies of Sensitized Bentonite for Methyl Orange and Rhodamine-B Adsorption from Wastewater: Experimental and DFT-Based Analysis

This work reports the formation of a novel adsorbent, prepared by activating bentonite with cinnamic acid, which is highly efficient to remove dyes from wastewater. The adsorption efficiency of the cinnamic acid activated bentonite was compared with unmodified bentonite by removing methyl orange and rhodamine-B from polluted water. The characterization was performed through X-ray diffraction (XRD) Fourier transform infrared (FTIR) and scanning electron microscopy (SEM). The results indicated that acidic pH and low temperature were more suitable for the selected dyes adsorption. The analysis of the data was done by the Langmuir and Freundlich isotherms; the Freundlich isotherm showed more suitability for the equilibrium data. The data were further analyzed by pseudo-first and pseudo-second-order models to study adsorption kinetics. The results showed that methyl orange and rhodamine-B adsorption obeyed pseudo-order kinetics. The results obtained from this research suggested that acid activation of bentonite with cinnamic acid increased the surface area of the clay and hence enhanced its adsorption efficiency. The maximum adsorption efficiency for the removal of methyl orange and rhodamine-B was up to 99.3 mg g⁻¹ and 44.7 mg g⁻¹, respectively, at 25 °C. This research provides an economical modification technique of bentonite, which makes it cost-effective and a good adsorbent for wastewater treatment.

Magnesium ferrite-nitrogen-doped graphene oxide nanocomposite: effective adsorptive removal of lead(II) and arsenic(III)

Magnetic nanocomposites have received immense interest as adsorbents for water decontamination. This paper presents adsorptive properties of nitrogen-doped graphene oxide (N-GO) with magnesium ferrite (MgFe₂O₄) magnetic nanocomposite for removing lead(II) (Pb(II)and arsenite As(III) ions. Transmission electron microscope (TEM) image of synthesized nanocomposite revealed the wrinkled sheets of N-GO containing MgFe₂O₄ nanoparticles (NPs) with particle size of 5-15 nm distributed over its surface. This nanocomposite displayed higher BET surface area (72.2 m²g^-1) than that of pristine MgFe₂O₄ NPs (38.4 m²g^-1). Adsorption on the nanocomposite could be described by the Langmuir isotherm with the maximum adsorption capacities were 930 mg/g, and 64.1 mg/g for Pb(II) and As(III), respectively. Whereas, maximum removal efficiencies were observed to be 99.7 [Formula: see text] 0.2% and 93.5 [Formula: see text] 0.1% for Pb(II) and As(III), respectively. The study on the effect of coexisting anions on the adsorption of metal ions showed that the phosphate ions were potential competitors of Pb(II) and As(III) ions to adsorb on the nanocomposite. Significantly, the investigation on adsorption of metal ion in the presence of coexisting heavy metal ions indicated the preferential adsorption of Pb(II) ions as compared to Cd(II), Zn(II) and Ni(II) ions. The effectiveness of the nanocomposite to remove the metal ions in electroplating wastewater was demonstrated.

Rationally designed carboxymethylcellulose-based sorbents crosslinked by targeted ions for static and dynamic capture of heavy metals: Easy recovery and affinity mechanism

A separable spherical bio-adsorbent (CMC-Cr) was prepared for capturing heavy metal ions by simple coordination and cross-linking between targeted ions of Cr³⁺ and carboxymethyl cellulose (CMC). A simple alternation of the CMC incorporation allowed the interconnected networks within the microspheres of preformed solid CMC to be adjusted. The excellent network structure could achieve the maximum collision between the adsorbent and the heavy metal cations in the wastewater. Through investigations, CMC-Cr-2 beads were determined as the optimal adsorbent. The adsorption performance of novel materials was evaluated by examining their adsorption behavior on Pb(II) and Co(II) under both static and dynamic conditions. The results showed that the adsorption behavior of CMC-Cr-2 beads on both two heavy metal cations could be fully reflected by the Freundlich model. Under the theoretical conditions, the maximum adsorption capacities were 97.26 and 144.74 mg/g. The kinetic results for the adsorption of two heavy metal cations on CMC-Cr-2 beads were consistent with the Pseudo-second-order kinetic model. Moreover, the correlation coefficient of the Thomas model was significant in the dynamic adsorption performance tests. Five regeneration cycle studies were successfully carried out on CMC-Cr-2 beads to evaluate reusability and stability. The applicability of CMC-Cr-2 beads in authentic aqueous solutions (both the single and binary pollutant systems) was also studied, and the results indicated that CMC-Cr-2 beads had a high potential for practical implementation. Furthermore, by analyzing the surface interactions of two heavy metal cations with the CMC-Cr-2 beads based on FTIR and XPS characterization, a basic understanding of the interaction between bio-sorbents and pollutants in wastewater can be obtained.

A post-functional Ti-based MOFs composite for selective removal of Pb (II) from water

Lead ions in water have notorious effects on humans and environment. It is important to design an adsorbent with high adsorption capacity and reproducibility for efficiently removing Pb (II)ions from polluted water. Here, a novel Ti-based MOFs material (BDB-MIL-125(Ti)@Fe₃O₄) was prepared by modifying NH₂-MIL-125(Ti) with sulfhydryl and amino groups. Due to the large number of active sites, the maximum Pb (II) adsorption capacity of BDB-MIL-125(Ti)@Fe₃O₄ was 710.79 mg/g at 25 °C and pH = 6 within 120 min corresponding to a maximum removal rate of 95.68%. The adsorbent also has extremely high selectivity and good cycling adsorption performance. The adsorption isotherms and kinetics agree with the Langmuir and the pseudo-second-order models, indicating that the process was chemisorption. Thermodynamic studies prove that spontaneous processes enhance Pb (II) adsorption at higher temperatures. DFT and FMOs calculations were used to discuss the adsorption mechanism. The sulfhydryl groups on the surface of organic ligands have a stronger affinity for Pb (II).

Adsorption performance and its mechanism of aqueous As(III) on polyporous calcined oyster shell-supported Fe-Mn binary oxide

Fe-Mn binary oxide (FMBO) is a promising adsorbent for As(III) removal through combined adsorption and oxidation. The calcined oyster shell-supported Fe-Mn binary oxide (FMBO/OS) adsorbent was synthesized by the co-precipitation method. Results indicated that the calcined oyster shell, as a carrier, improved the stability of FMBO and its adsorption capacity for As(III). The maximum adsorption capacity of FMBO/OS on As(III) reached 140.5 mg·g^-1 . Under pH 5.0 and 25°C, the removal efficiency of FMBO/OS to As(III) solution (C₀  = 10 mg·L^-1 ) reached 87% within 12 h. Moreover, based on the characterization analyses, the removal mechanisms of As(III) were deduced to include the combined adsorption and oxidation process of FMBO and the synergistic effect of oyster shells. This work provides new insights into synthesizing efficient and green adsorbents to remove aqueous As(III). Meanwhile, it provides technical support for reusing waste biomass materials such as the oyster shell. PRACTITIONER POINTS: FMBO/OS was prepared by a simple hydrothermal co-precipitation method. The carrier alleviates the agglomeration of Fe-Mn oxides. The adsorbent shows a strong adsorption capacity of As(III) and good selectivity. The good results benefit from the synergistic effect of calcium arsenate generation. The prepared adsorbent can adsorb arsenic in real samples.

Performance of novel GO-Gly/HNTs and GO-GG/HNTs nanocomposites for removal of Pb(II) from water: optimization based on the RSM-CCD model

For the first time, in this study, two novel glycogen-graphene oxide/halloysite nanotubes (GO-Gly/HNTs) and guar gum-graphene oxide/halloysite nanotubes (GO-GG/HNTs) nanocomposites were synthesized as the adsorbents for removal of Pb(II) from water, and the ionic liquid was used in the synthesis as a green solvent. According to the SEM, TEM, EDS, BET, zeta potential, FTIR, and XRD results, GO-Gly/HNTs and GO-GG/HNTs were synthesized successfully. Response surface methodology (RSM) was applied to optimize the experimental conditions. Nanocomposites followed the Langmuir equilibrium model and were best fitted to the pseudo-second-order model. According to the thermodynamic model, the adsorption process was endothermic. Due to several features, these two novel nanocomposites can be considered the proper candidate for Pb(II) removal from water and wastewater. First, these nanocomposites have good adsorption capacity for Pb(II) removal, which is 219 mg/g for GO-Gly/HNTs and 315 mg/g for GO-GG/HNTs. Moreover, nanocomposites can be recycled with proper adsorption capacity after four repeated cycles. These materials can be used to remove Pb(II) from water in the presence of other contaminants because nanocomposites have selective tendency toward Pb(II) in the presence of other pollutants such as Cd²⁺, Cu²⁺, Cr²⁺, and Co²⁺. In addition, the presence of Ca²⁺, Mg²⁺, Na⁺, and K⁺ improve Pb(II) removal. Finally, possible mechanisms for each nanocomposite were represented.

HTDMA-modified bentonite clay for effective removal of Pb(II) from aqueous solution

This work studies the Pb(II) removal onto bentonite clay modified by hexadecyl trimethyl ammonium bromide (HDTMA). Characterizations of the unmodified and modified materials were performed by using XRD, SEM, TG-DSC, FT-IR, and BET surface area analyses. Factors influencing the uptake of Pb(II) from aqueous solution, such as pH_solution, ion strength, uptake time, adsorbent dosage, and initial Pb(II) concentration, were examined. The obtained results showed that bentonite clay was successfully modified by HDTMA, resulting in an increase in its surface area by about 70 %. The Pb(II) adsorption onto modified bentonite clay reached equilibrium at pH = 5.0 after 120 min. Studies within the isotherm and kinetic models demonstrated that the adsorption followed the Sips isotherm and pseudo-second-order kinetic models. The maximum monolayer adsorption capacity calculated from the Langmuir model at 30 °C was 25.8 mg/g, which is much higher than that obtained for the unmodified sample (18.9 mg/g). The FT-IR and TG-DSC analyses indicated that the formation of inner-sphere complexes plays a fundamental role in the mechanism of Pb(II) uptake onto HDTMA-bentonite clay. This mechanism of Pb(II) adsorption was further investigated, for the first time, by using the positron annihilation lifetime (PAL) and electron momentum (EMD) measurements. The PAL and EMD analyses indicated that the existence of Al and Si mono-vacancies in the HDTMA-bentonite should have essential contributions to the adsorption mechanism. In particular, we found a very interesting mechanism that the Pb(II) adsorption should occur inside the interlayer spaces of the HDTMA-bentonite.

Removal of Lead by Merlinoite Prepared from Sugarcane Bagasse Ash and Kaolin: Synthesis, Isotherm, Kinetic, and Thermodynamic Studies

This study introduces a merlinoite synthesized from sugarcane bagasse ash (SBA) and kaolin and evaluates its application as an adsorbent to remove lead from wastewater. The synthesis was performed via the hydrothermal method, and optimal conditions were determined. The adsorption of Pb by merlinoite was also optimized. Determination of the Pb2+ remaining in the aqueous solution was determined by atomic absorption spectroscopy (AAS). Adsorption isotherms were mainly studied using the Langmuir and Freundlich models. The Langmuir model showed the highest consistency for Pb adsorption on merlinoite, yielding a high correlation coefficient (R2) of 0.9997 and a maximum adsorption capacity (qmax) of 322.58 mg/g. The kinetics of the adsorption process were best described by a pseudo-second-order model. Thermodynamic studies carried out at different temperatures established that the adsorption reaction was spontaneous and endothermic. The results of this study show that merlinoite synthesized from kaolinite and SBA is an excellent candidate for utilization as a high-performance adsorbent for lead removal from wastewater.

Efficient Removal of Pb(II) from Aqueous Medium Using Chemically Modified Silica Monolith

The adsorptive removal of lead (II) from aqueous medium was carried out by chemically modified silica monolith particles. Porous silica monolith particles were prepared by the sol-gel method and their surface modification was carried out using trimethoxy silyl propyl urea (TSPU) to prepare inorganic–organic hybrid adsorbent. The resultant adsorbent was evaluated for the removal of lead (Pb) from aqueous medium. The effect of pH, adsorbent dose, metal ion concentration and adsorption time was determined. It was found that the optimum conditions for adsorption of lead (Pb) were pH 5, adsorbent dose of 0.4 g/L, Pb(II) ions concentration of 500 mg/L and adsorption time of 1 h. The adsorbent chemically modified SM was characterized by scanning electron microscopy (SEM), BET/BJH and thermo gravimetric analysis (TGA). The percent adsorption of Pb(II) onto chemically modified silica monolith particles was 98%. An isotherm study showed that the adsorption data of Pb(II) onto chemically modified SM was fully fitted with the Freundlich and Langmuir isotherm models. It was found from kinetic study that the adsorption of Pb(II) followed a pseudo second-order model. Moreover, thermodynamic study suggests that the adsorption of Pb(II) is spontaneous and exothermic. The adsorption capacity of chemically modified SM for Pb(II) ions was 792 mg/g which is quite high as compared to the traditional adsorbents. The adsorbent chemically modified SM was regenerated, used again three times for the adsorption of Pb(II) ions and it was found that the adsorption capacity of the regenerated adsorbent was only dropped by 7%. Due to high adsorption capacity chemically modified silica monolith particles could be used as an effective adsorbent for the removal of heavy metals from wastewater.

Preparation and Characterization of Phosphoric Acid-Modified Biochar Nanomaterials with Highly Efficient Adsorption and Photodegradation Ability

Phosphoric acid-modified biochar (PMBC) was prepared using biochar (BC) as the carbon source and phosphoric acid as the activating agent. The PMBC exhibited an ordered vessel structure after deashing treatment, but the sidewalls became much rougher, the polarity (O/C atomic ratio of BC = 0.2320 and O/C atomic ratio of PMBC = 0.1604) decreased, and the isoelectric points (PI of BC = 5.22 and PI of PMBC = 5.51) and specific surface area (SSA of BC = 55.322 m²/g and SSA of PMBC = 62.285 m²/g) increased. The adsorption characterization of the removal of sulfadiazine (SDZ) from PMBC was studied. The adsorption of SDZ by PMBC was in accordance with the Langmuir isotherm model and the pseudo-second-order kinetics model, and the adsorption thermodynamics were shown as Gibbs free energy < 0, an enthalpy change of 19.157 kJ/mol, and an entropy change of 0.0718 kJ/(K·mol). The adsorption of SDZ by PMBC was a complicated monolayer adsorption that was spontaneous, irreversible, and endothermic, and physical adsorption and chemical adsorption occurred simultaneously. The adsorption process was controlled by microporous capture, electrostatic interactions, hydrogen-bond interactions, and π-π interactions. PMBC@TiO₂ photocatalysts with different mass ratios between TiO₂ and PMBC were prepared via the in situ sol-gel method. PMBC@TiO₂ exhibited both an ordered vessel structure (PMBC) and irregular particles (TiO₂), and it was linked via Ti-O-C bonds. The optimal mass ratio between TiO₂ and PMBC was 3:1. The removal of SDZ via PMBC@TiO₂ was dependent on the coupling of adsorption and photocatalysis. The PMBC-enhanced photocatalytic performance of PMBC@TiO₂ resulted in a higher absorption of UV and visible light, greater generation of reactive oxygen species, high levels of adsorption of SDZ on PMBC, and the conjugated structure and oxygen-containing functional groups that promoted the separation efficiency of the hole-electron pairs.

Surfactant-assisted adsorption of uranyl ions in aqueous solution on TiO2/polythiophene nanocomposite

In this work, hexadecyltrimethylammonium-bromide (HTAB)-modified polythiophene (PTh)/TiO₂ nanocomposite (HTAB/PTh/TiO₂) was applied to remove uranyl ions (UO₂²⁺). FT-IR, XRD, ζ potential, TGA, SEM, and XPS were utilized to obtain the chemical and physical properties of HTAB/PTh/TiO₂. The effects of HTAB content, preparation temperature, and adsorption conditions on UO₂²⁺ removal were investigated comprehensively. And the UO₂²⁺ adsorption process on HTAB/PTh/TiO₂ was fitted to the Sips model with a saturated adsorption capacity of 234.74 mg/g, which was 6 times over TiO₂. The results suggested that the surfactant of HTAB can significantly improve the adsorption ability of TiO₂ for UO₂²⁺ ions. This work provides a strategy of surfactant modification for enhancing the separation and recovery ability of adsorbent toward UO₂²⁺ in the radioactive wastewater.

Carboxymethylcellulose-chitosan film modified magnetic alkaline Ca-bentonite for the efficient removal of Pb(II) and Cd(II) from aqueous solution

In order to endow alkaline Ca-bentonite (ACB) with magnetic separation ability, simultaneously obtain better magnetic stability and stronger removal capacity of heavy metal cations; magnetic alkaline Ca-bentonite/carboxymethylcellulose-chitosan film (MACB/C-C) was prepared by organic modification of magnetic alkaline Ca-bentonite (MACB) using non-toxic carboxymethylcellulose and chitosan. Textural characterization results revealed that magnetic Fe3O4 nanoparticles were successfully immobilized on ACB and modified with C-C. The functionalized layer of C-C concurrently enhanced the stability of Fe3O4 and removal performances of heavy metal cations. Adsorption results indicated that MACB/C-C exhibited thorough separation from aqueous solution and greater uptake ability for Pb(II) and Cd(II) (483 mg·g-1 and 123 mg·g-1) than the nascent MACB (335 mg·g-1 and 76 mg·g-1), respectively, at pH 5 and 25 °C temperature. The adsorption of Pb(II) and Cd(II) on MACB/C-C mainly occurred via surface precipitation and complexation when pH > 2. MACB/C-C could be efficiently recycled with marginal decrease in adsorption capacity. The current approach credited to the convenient operation, simplified synthesis, and high efficiency of MACB/C-C could be deemed as a promising alternative for the removal of heavy metal cations from wastewater.

Synthesis of wheat bran sawdust/Fe3O4 composite for the removal of methylene blue and methyl violet

Magnetically modified nanomaterials have recently gained a great attention in wastewater treatment. In this study, the uptake process of methylene blue (MB) and methyl violet (MV) from aqueous media using wheat bran sawdust/Fe₃O₄ composite was studied. To specify the surface and structural properties of the wheat bran sawdust/Fe₃O₄ composite, various analyses such as FTIR, XRD, EDX, Map, TGA/DTG, SEM, VSM, and BET were performed. The results of BET analysis indicated that the specific surface area of the aforementioned composite was 74.25 m²/g, and the average pore size was 65.7A, which indicates that the composite has a mesoporous structure. Also, VSM analysis indicated that the composite has a paramagnetic property with a magnetic saturation of 28.29 emu/g and can be easily eliminated from the aqueous solution by a magnet. Moreover, the highest removal efficiency of MB and MV dyes using the wheat bran/Fe₃O₄ composite was obtained as 97.46 and 98.75%, respectively, which were significant values. These removal efficiencies were obtained at contact time of 50 min and pH values of 9 and 8 for MB and MV, respectively. Furthermore, the outcomes of equilibrium study showed that the Langmuir model with a correlation coefficient greater than 0.98 describes the equilibrium behavior of the uptake process better than the Freundlich and Dubinin-Radushkevich models. Besides, the maximum sorption capacity of MV and MB dyes using the Langmuir model was obtained as 46.08 and 51.28 mg/g, respectively. Also, the uptake process followed the pseudo-second-order kinetic model, and the thermodynamic study indicated that the uptake process is exothermic and spontaneous.

Cellulose-Based Hydrogels for Wastewater Treatment: A Concise Review

Finding affordable and environment-friendly options to decontaminate wastewater generated with heavy metals and dyes to prevent the depletion of accessible freshwater resources is one of the indispensable challenges of the 21st century. Adsorption is yet to be the most effective and low-cost wastewater treatment method used for the removal of pollutants from wastewater, while naturally derived adsorbent materials have garnered tremendous attention. One promising example of such adsorbents is hydrogels (HGs), which constitute a three-dimensional polymeric network of hydrophilic groups that is highly capable of adsorbing a large quantity of metal ions and dyes from wastewater. Although HGs can also be prepared from synthetic polymers, natural polymers have improved environmental benignity. Recently, cellulose-based hydrogels (CBHs) have been extensively studied owing to their high abundance, biodegradability, non-toxicity, and excellent adsorption capacity. This review emphasizes different CBH adsorbents in the context of dyes and heavy metals removal from wastewater following diverse synthesis techniques and adsorption mechanisms. This study also summarizes various process parameters necessary to optimize adsorption capacity followed by future research directions.

The biosorption of reactive red dye onto orange peel waste: a study on the isotherm and kinetic processes and sensitivity analysis using the artificial neural network approach

The agricultural waste of orange peels (OPs) was utilized as a cheap biosorbent and then tested for its ability to treat the reactive red (RR) dye wastewater. Several experiments were done to get the equilibrium isotherm and kinetic-relevant data. In addition, several experimental factors such as solution pH, temperature, contact time, and initial RR dye concentration were studied, in light of their impact on the biosorption process. The utilized isotherm and kinetic models were evaluated by using the chi-square test and coefficient of determination parameters for their representation of real data. In addition, the obtained data of their biosorption capacities, at different conditions, were modeled by the artificial neural network (ANN) approach. The results of the isotherm study revealed that the experimental data can be best accounted by both the Langmuir and Temkin models, demonstrating that the RR molecules were sorbed to two or more different types of biosorption sites of OP. The kinetic study for determining the characteristics of the rate of diffusion demonstrated that the intraparticle diffusion process was not the sole rate-limiting step in the biosorption of the RR dye-OP couple. Furthermore, the biosorption process was chemisorption in nature, as the pseudo-second-order reaction proved to be the best representative model for the kinetic data. The outcome of modeling also assumed that using the ANN tool was useful to reproduce the data again and foretell the manner in which biosorption behaved. According to the results of the Langmuir model, it was found that the maximum OP uptake for the biosorption of the RR dye was up to 82 mg/g, observed at optimized values of the experimental parameters. Such prior results highlight that OP is an effective agent of biosorption in the elimination of RR dyes from polluted solutions, moreover, in a cost-effective manner.

Clay-activated carbon adsorbent obtained by activation of spent bleaching earth and its application for removing Pb(II) ion

BE/C-A750-1/1 is prepared by carbonizing SBE and then activating with KOH. BE/C-A750-1/1 has good adsorption capacity for Pb(II), and the adsorption capacity for Pb(II) is 206.65 mg/g. The harmful effects of coexisting cations are listed in ascending order: K⁺ < Na⁺ < Mg²⁺. Adsorption and desorption studies show that the adsorption capacity of BE/C-A750-1/1 for Pb(II) after adsorption and desorption 3 times is 183.62 mg/g. The adsorption mechanism mainly includes electrostatic attraction, ion exchange, physical adsorption, and chemical complexation. This suggests that activated BE/C may be a promising candidate for removing Pb(II) from industrial wastewater. Clay/carbon nanocomposites were prepared by carbonizing and activating the spent bleaching earth served as adsorbents for the efficient removal of Pb(II) from wastewater.

The advantages of clay mineral modification methods for enhancing adsorption efficiency in wastewater treatment: a review

This review discusses the recent trends in the research over the last 30 years to use clay minerals in natural and modified forms for removing different toxic organic/inorganic pollutants. The natural and modified forms of clay minerals have an exceptional ability to remove different contaminants. However, the modification methods can improve the clay mineral adsorption properties that consequently increase more adsorption sites and functional groups to adsorb different environmental pollutants. This review shows the importance of modification methods and more extension of novel clay preparation based on nanotechnology which could raise the control of pollution. The syntheses of functionalized clays such as pillared clays and porous clay heterostructures introduce the new class of heterostructure materials with high adsorption capacity, capability, and selectivity. Due to the acceptable properties of heterostructure materials including high specific surface area, thermal and mechanical stability, and the existence of multifunctional groups to selective adsorption, this review collects more literature of research related to environmental protection issues. However, it is expected much attention to get a better understanding of the adsorption mechanism, regeneration, and recovery process of these materials.

Lead adsorption on loess under high ammonium environment

Lead (Pb) is one of the most toxic, hazardous pollutants available in landfill leachate. Loess-amended soil buffers are found suitable and effective in attenuating migration of Pb and the other trace metals. High concentration of ammonium (NH₄⁺ > 1000 mg/l) is also reported in landfill leachate, and therefore, it is essential to investigate the transport of lead under such condition. In this study, the mechanisms and the capacity of loess to adsorb Pb under high NH₄⁺ concentration were investigated. Adsorption isotherm test data were obtained for 25 °C, 35 °C and 45 °C. The maximum adsorption capacity is estimated to be 2101.97 mg/g at 25 °C and 4292.8 mg/g at 45 °C under 1000 mg/l NH₄⁺. The binding sites of Pb on loess are positively related to each other at low temperatures (25-35 °C). The thermodynamic analysis indicates that adsorption process is endothermic and non-spontaneous and the system randomness increases with reaction time. The kinetic test data, fitted with a pseudo-second-order kinetic model and an intraparticle diffusion model, suggests that removal of Pb is driven by both membrane and intraparticle diffusions. The SEM, XRD and FTIR analyses indicate flocculation, precipitations as well as some ion exchange processes, which perhaps combinedly increases adsorption of both NH₄⁺ and Pb in loess. The two kinds of precipitations are involved for the removal of Pb. The precipitations of PbCO₃, Pb(OH)₂ and PbCO₃·2H₂O are formed by the reactions between calcite and lead. The other precipitation of white basic salt (Pb₂O(NO₃)₂) is formed by the reactions among Pb²⁺, NO₃^- and aqueous ammonia under alkaline environment of loess slurry.

Exploring of toxic Pb(II) removal by low-cost bio-adsorbent of camphor leaf forestry waste after camphor oil extraction

Camphor leaf (CL) was widely used to extract camphor oil and thus led to abundant forestry waste. In order to reduce pollution, the waste CL was used to prepare bio-adsorbent for Pb(II) removal after alkali treatment and functional modification. The effects of solution pH, initial Pb(II) concentration, contact time and solution temperature were investigated on adsorption process to evaluate the potential application in heavy metal ions' removal. It was found that the massive hydroxyl groups released and plenty of micro-pores formed after the alkali treatment of CL bio-adsorbent, which obviously increased the Pb(II) adsorption. And the adsorption performance promoted continually after further functional modification by ionized 1,2,3,4-butanetetracarboxylic acid (BTCA). The increase of pH was favourable for the adsorption even though the precipitation effect was deducted. Linear fitting method was more suitable to describe the adsorption process than nonlinear fitting method, including adsorption isotherms and adsorption kinetics research. The adsorption thermodynamics was better to be described by nonlinear fitting method due to its lower root mean square error (RMSE) value and higher R² value. Among which, the adsorption isotherm and adsorption kinetics were fitted well to Langmuir model and pseudo-second-order model, respectively. The adsorption thermodynamics was exothermic in nature and the process was spontaneous at low solution temperature. The adsorption mechanism was revealed as the combination of dominant chemical adsorption and assistant physical adsorption.

Physico-chemical processes

By summarizing 187 relevant research articles published in 2019, the review is focused on the research progress of physicochemical processes for wastewater treatment. This review divides into two sections, physical processes and chemical processes. The physical processes section includes three sub-sections, that is, adsorption, granular filtration, and dissolved air flotation, whereas the chemical processes section has five sub-sections, that is, coagulation/flocculation, advanced oxidation processes, electrochemical, capacitive deionization, and ion exchange. PRACTITIONER POINTS: Totally 187 research articles on wastewater treatment have been reviewed and discussed. The review has two major sections with eight sub-topics.

Ultrasonic-assisted synthesis of natural clay/Fe3O4/graphene oxide for enhance removal of Cr (VI) from aqueous media

In this study, Fe3O4/graphene oxide (GO)/clay composite was used to remove chromium (VI) ion from aqueous media. The structure and characteristics of the Fe3O4/GO/clay composite were investigated using FT-IR, SEM, EDX/Map, VSM, BET, and XRD analyses. The BET analysis indicated that the specific surface area and mean pore size of the Fe3O4/GO/clay composite were calculated as 61.64 m2/g and 16.2 nm respectively, which indicate that the composite has a mesoporous structure. Also, the VSM analysis showed that the Fe3O4/GO/clay composite has a superparamagnetic property. Moreover, the highest removal efficiency of Cr (VI) from aqueous media was obtained to be 98.84%, which achieved at pH 3, Cr (VI) ion concentration of 10 mg/L, the composite dosage of 1 g/L, contact time of 60 min, and temperature of 25 °C. Furthermore, the kinetic and equilibrium studies showed that the quasi second-order kinetic model and the Langmuir model could better describe the sorption behavior of the clay and the Fe3O4/clay composite, while the behavior of the Fe3O4/GO/clay composite can be better explained by the Freundlich model. Besides, the maximum sorption capacities of the clay, Fe3O4/clay, and Fe3O4/GO/clay composite were obtained to be 49.61, 62.26, and 71.47 mg/g, respectively, which shows that the maximum sorption capacity of the clay increases with improving the surface properties of the clay. Also, the thermodynamic study indicated that the Cr (VI) sorption process was exothermic and spontaneous in nature. In general, the results indicated that the Fe3O4/GO/clay composite was more effective than the clay and the Fe3O4/clay in Cr (VI) ion removal.

Conversion synthesis of manganese sulfate residue into iron hydroxide adsorbent for Cu(II) removal from aqueous solution

Manganese sulfate residue (MSR) is a by-product derived from the manganese sulfate production process. In this study, an iron hydroxide adsorbent was prepared from MSR using the hydrothermal conversion method. The adsorbent was characterized and used to remove copper(II) ions from aqueous solution. Batch experiments were performed to investigate the adsorption efficiency of copper ions at different contact times, initial concentrations, solution pH levels, and reaction temperatures. Adsorption equilibrium was observed in 3 h, and the best pH was under natural conditions (pH ∼ 5.5). Increasing the initial Cu²⁺ concentration and reaction temperature can increase the adsorption quantity. The adsorption capacity of iron hydroxide at an initial concentration of 50 mg L^-1 was 14.515 mg g^-1 Cu(II) under the conditions of a nature pH and room temperature. According to the adsorption data, the pseudo-second-order model can describe the adsorption kinetics of copper ions well, and the Freundlich model provides an excellent fit to the adsorption isotherm. XRD and FTIR were applied to characterize the raw materials and adsorbents to reveal the adsorption mechanism. The results suggest that the adsorbent converted from MSR is a promising material for the removal of Cu(II) in aqueous solutions.

Enhanced Pb(II) adsorption onto functionalized ordered mesoporous carbon (OMC) from aqueous solutions: the important role of surface property and adsorption mechanism

Functionalized ordered mesoporous carbon (MOMC-NP) was synthesized by chemical modification using HNO₃ and H₃PO₄ to enhance Pb(II) adsorption. The phosphate functional group represented by P-O-C bonding onto the surface of OMC was verified by FT-IR and XPS. Batch adsorption experiments revealed the improvement of adsorption capacity by 39 times over the virgin OMC. Moreover, the Pb(II) adsorption results provided excellent fits to Langmuir model and pseudo-second-order kinetic model. The adsorption mechanism of Pb(II) onto MOMC-NP revealed the formation of metal complexes with carboxyl, hydroxyl, and phosphate groups through ion exchange reactions and hydrogen bondings. The calculated activation energy was 22.09 kJ/mol, suggesting that Pb(II) adsorption was a chemisorption. At pH>pH_pzc, the main Pb(II) existing species of Pb(II) and Pb(OH)⁺ combine with the carboxyl, hydroxyl, and phosphate functional groups via electrostatic interactions and hydrogen bonding. All these findings demonstrated that MOMC-NP could be a useful and potential adsorbent for adsorptive removal of Pb(II). Graphical abstract.

Evaluation of groundwater hardness removal using activated clinoptilolite

Current study aimed to investigate modified natural clinoptilolite for removal of calcium and magnesium from the groundwater. Feasibility of clinoptilolite for groundwater hardness removal in production and operation was verified by static adsorption experiment and the experiment of fixed bed and degasification column. Subsequently, the main parameters for groundwater treatment using clinoptilolite were also explored. Results show that in the process of clinoptilolite in adsorption is dominant reaction process. The adsorption equilibrium time was unchanged when the hardness of raw water changes from 450 to 550 mg/L. With respect to comparative analysis of price and performance, NaCl found to be the most suitable clinoptilolite regenerated agent. The adsorption efficiency was high when the residence time was 20-25 min in the pilot experiments. The reaction mechanism was mainly substitution reaction according to ion equilibrium, and the treatment capacity of the degasifier combined with the fixed bed was 20% higher than that of with only fixed bed.

Elaboration of novel polyaniline@Almond shell biocomposite for effective removal of hexavalent chromium ions and Orange G dye from aqueous solutions

A novel polyaniline@Almond shell (PANI@AS) biocomposite was synthesized via facile in situ chemical polymerization method. The as-synthesized adsorbent was characterized using various analytical techniques such as Fourier transform infrared spectroscopy (FTIR), X-ray energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM), and potentiometric titration. A batch adsorption system was applied with the aim of investigating as-synthesized adsorbent ability to remove Cr(VI) ions and Orange G (OG) textile dye from aqueous solutions. Obtained results revealed that adsorption process was strongly depended upon the physicochemical parameters. The adsorption of Cr(VI) and OG dye onto PANI@AS was better described by the pseudo second-order-kinetic model and followed the Freundlich isotherm model. The maximum uptakes were 335.25 for Cr(VI) and 190.98 mg g^-1 for OG dye. We further evaluated that PANI@AS biocomposite could be regenerated easily with NaOH solution and efficiently reused for Cr(VI) and OG dye removal from aqueous media. Thus, these results indicated the potential practical application of PANI@AS biocomposite for wastewater treatment.

Removal of Hg2+ by carboxyl-terminated hyperbranched poly(amidoamine) dendrimers grafted superparamagnetic nanoparticles as an efficient adsorbent

In this research, carboxyl-terminated hyperbranched poly(amidoamine) dendrimers grafted superparamagnetic nanoparticles (CT-HPMNPs) with core-shell structure were synthesized by the chemical co-precipitation method, the core of superparamagnetic iron oxide nanoparticles and a shell of polyamidoamines (PAMAM) and carboxyl groups, as a novel adsorbent for removing Hg²⁺ from aqueous systems. The surface of the particles was modified by 3-(aminopropyl) triethoxysilane, and finally, PAMAM and carboxyl dendrimers were grown on the surface up to 5.5 generation. The synthesized polymer was characterized physically and morphologically using different techniques. Also, they were evaluated in terms of adsorption capacity to remove inorganic pollutants of Hg²⁺, selectivity, and reusability. The adsorption mechanism Hg²⁺ onto CT-HPMNPs was investigated by single-step and two-step isotherms that the adsorption capacity of Hg²⁺ obtained 72.3 and 32.88 mg g^-1 respectively at pH 5, adsorbent dosage 2 g L^-1, Hg²⁺ initial concentrations 20 mg L^-1, contact time 60 min, and temperature of 298 K by CT-HPMNPs. Also, the kinetics of Hg²⁺ followed the pseudo-second-order model and adsorption isotherms of Hg²⁺ onto CT-HPMNPs were fitted well by Freundlich (as a single-step) and two-step adsorption models with a correlation coefficient of 0.9997 and 0.9999 respectively. The results showed a significant potential of Hg²⁺ ions removing from industrial wastewater and spiked water by CT-HPMNPs.

Pb2+ biosorption from aqueous solutions by live and dead biosorbents of the hydrocarbon-degrading strain Rhodococcus sp. HX-2

In this study, the Pb²⁺ biosorption potential of live and dead biosorbents of the hydrocarbon-degrading strain Rhodococcus sp. HX-2 was analyzed. Optimal biosorption conditions were determined via single factor optimization, which were as follows: temperature, 25°C; pH, 5.0, and biosorbent dose, 0.75 g L⁻¹. A response surface software (Design Expert 10.0) was used to analyze optimal biosorption conditions. The biosorption data for live and dead biosorbents were suitable for the Freundlich model at a Pb²⁺ concentration of 200 mg L⁻¹. At this same concentration, the maximum biosorption capacity was 88.74 mg g⁻¹ (0.428 mmol g⁻¹) for live biosorbents and 125.5 mg g⁻¹ (0.606 mmol g⁻¹) for dead biosorbents. Moreover, in comparison with the pseudo-first-order model, the pseudo-second-order model seemed better to depict the biosorption process. Dead biosorbents seemed to have lower binding strength than live biosorbents, showing a higher desorption capacity at pH 1.0. The order of influence of competitive metal ions on Pb²⁺ adsorption was Cu²⁺ > Cd²⁺ > Ni⁺. Fourier-transform infrared spectroscopy analyses revealed that several functional groups were involved in the biosorption process of dead biosorbents. Scanning electron microscopy showed that Pb²⁺ attached to the surface of dead biosorbents more readily than on the surface of live biosorbents, whereas transmission electron microscopy confirmed the transfer of biosorbed Pb²⁺ into the cells in the case of both live and dead biosorbents. It can thus be concluded that dead biosorbents are better than live biosorbents for Pb²⁺ biosorption, and they can accordingly be used for wastewater treatment.

Uptake of Pb(II) Ions from Simulated Aqueous Solution via Nanochitosan

In this work, nanochitosan (NC) was prepared through ionic gelation using low molecular weight chitosan and maleic acid (MA). The synthesized NC was characterized by atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). During preparation, the particle size of the material depended on parameters such as concentration of chitosan and pH of the aqueous solution. After controlling the mentioned parameters, NC smaller than 100 nm was prepared. The chitosan and prepared NC were employed for the adsorption of Pb(II) from an aqueous solution in the form of a batch system. Among the sorption parameters, pH showed the strongest effect on the sorption process and removal of the maximum number of Pb(II) ions was obtained at pH value of 6. Pseudo-first-order and pseudo-second-order models were used to track the kinetics of the adsorption process. Langmuir and Freundlich’s isotherms were subjected to the absorption data to evaluate absorption capacity. NC proved to be an excellent adsorbent with a remarkable capacity to eliminate Pb(II) ions from aqueous solutions at multiple concentrations. The NC also showed better performance with a comparatively easier preparation process than in other reported work.