The effects of seawater on the hydration, microstructure and strength development of Portland cement pastes incorporating colloidal silica

Mitigation of Corrosion Initiated by Cl- and SO42--ions in Blast Furnace Cement Concrete Mixed with Sea Water

The use of blast furnace cement is an effective way to meet the requirements of sustainable development. However, CEM III/C is characterized by slow strength gain. The problem can be worse for plasticized reinforced blast furnace cement concretes mixed with sea water in view of shorter durability. The mitigation of corrosion in plasticized blast furnace cement concretes mixed with sea water can be provided through a composition of minor additional constituents, with percentage by mass of the main constituents: alkali metal compounds, 2…3; calcium aluminate cement, 1; clinoptilolite, 1. The alkali metal compounds are known to activate hydraulic properties of ground granulated blast furnace slag. A calcium aluminate cement promotes the accelerated chemical binding of Cl⁻ and SO₄²⁻-ions with the formation of Kuzel’s salt. A clinoptilolite occludes these aggressive ions. The positive effects of the mentioned minor additional constituents in the blast furnace cement were supported by the increased early strength gain and the higher structural density, as well as by a good state of steel reinforcement, in the plasticized concretes mixed with sea water.

Modification of Lightweight Aggregate Concretes with Silica Nanoparticles-A Review

The use of lightweight concrete (LWC) for structural and non-structural applications has attracted great interest in recent years. The main benefits include reduced deadload of structural elements and generally lower production and transportation costs. However, a decrease in concrete density often leads to a decrease in strength and durability. Typically, concretes are mostly modified with mineral additives such as silica fume or fly ash. Because of the recent developments in nanotechnology, research attention has turned to the possibility of improving concrete properties with nanomaterials, i.e., nano-SiO₂. However, there are still certain issues with the dosage and efficiency of nanomaterials. Therefore, in order to establish the current state of knowledge in this field, this review gathers most recent results about the performance of LWC modified with nanomaterials. The review is divided into sections about the influence of nanoparticles on the fresh properties of concrete and their influence on the mechanical and durability characteristics. The paper studies in depth the most common approach to nanomaterials in concrete technology and proposes areas for further development.

Exploring Structural Evolution of Portland Cement Blended with Supplementary Cementitious Materials in Seawater

The present study investigated the structural evolution of Portland cement (PC) incorporating supplementary cementitious materials (SCMs) exposed to seawater. The samples were made with replacing Portland cement with 10 mass-% silica fume, metakaolin or glass powder. The reaction degree of SCMs estimated by the portlandite consumption shows that metakaolin has the highest reaction degree, thus metakaolin-blended PC exhibits the highest strength. The control exposed to seawater exhibited 14.82% and 12.14% higher compressive strengths compared to those cured in tap water at 7 and 28 days. The samples incorporating metakaolin showed the highest compressive strength of 76.60 MPa at 90 days tap water curing and this was 17% higher than that of the control. Exposure to seawater is found to retard the rate of hydration in all SCM-incorporating systems, while the strength development of the neat PC system is enhanced. The main reaction product that forms during exposure to seawater is Cl-AFm and brucite, while it is predicted by the thermodynamic modelling that a significant amount of M-S-H, calcite and hydrotalcite is to form at an extended period of exposure time.

The effects of nano- and micro-sized additives on 3D printable cementitious and alkali-activated composites: a review

Additive manufacturing (AM), also referred as 3D printing, is a technology that enables building automated three-dimensional objects in a layer-by-layer manner. AM of cement-based and alkali-activated composites has gathered attention over the last decade and is one of the most rapidly developing civil engineering fields. Development of proper mixture compositions which are suitable in fresh and hardened state is one of the key challenges of AM technology in construction. As the behaviour of cement-based materials (CBM) and alkali-activated materials (AAM) is determined by chemical and physical processes at the nano-level, incorporation of nano- and micro-sized admixtures has great influence on the performance of printable composites. These modifications are attributed to the unique reactivity of nanoparticles associated with their small size and large surface area. This review paper summarizes recent developments in the application of nano- and micro-particles on 3D printable cementitious composites and how they influence the performance of 3D-printed construction materials. The research progress on nano-engineered CBM and AAM is reviewed from the view of fresh and hardened properties. Moreover, comparison between nano- and micro-sized admixtures including nanosilica, graphene-based materials, and clay nanoparticles as well as chemical admixtures such as viscosity-modifying admixtures and superplasticizers is presented. Finally, the existing problems in current research and future perspectives are summarized. This review provides useful recommendations toward the significant influence of nano- and micro-sized admixtures on the performance of 3D printable CBMs.

The Effects of Temperature Curing on the Strength Development, Transport Properties, and Freeze-Thaw Resistance of Blast Furnace Slag Cement Mortars Modified with Nanosilica

This investigation studies the effects of hot water and hot air curing on the strength development, transport properties, and freeze-thaw resistance of mortars incorporating low-heat blast furnace slag cement and nanosilica (NS). Mortar samples were prepared and stored in ambient conditions for 24 h. After demolding, mortar samples were subjected to two different hot curing methods: Hot water and hot air curing (40 °C and 60 °C) for 24 h. For comparison purposes, mortar reference mixes were prepared and cured in water and air at ambient conditions. Strength development (from 1 to 180 days), capillary water porosity, water sorptivity, and freeze-thaw resistance were tested after 180 days of curing. The experimental results showed that both curing regimes accelerate the strength development of mortars, especially in the first seven days of hydration. The highest early strengths were reported for mortars subjected to a temperature of 60 °C, followed by those cured at 40 °C. The hot water curing regime was found to be more suitable, as a result of more stable strength development. Similar findings were observed in regard to durability-related properties. It is worth noting that thermal curing can more efficiently increase strength in the presence of nanosilica, suggesting that NS is more effective in enhancing strength under thermal curing.

The effects of calcium–silicate–hydrate (C–S–H) seeds on reference microorganisms

Building materials are constantly improved with various additives and admixtures in order to achieve goals ranging from obtaining increased durability or antimicrobial activity up to reducing the carbon footprint left by the cement production. Since nanomaterials were proposed for cement products, many studies explored the possibilities for their incorporation. One of the novel trends in studying these materials is evaluating their impact on living organisms, with the focus not only on toxicology but also on the application potential. Therefore, in this study, we investigated the effects of three types of calcium–silicate–hydrate (C–S–H) seeds on reference microorganisms in the scope of their basic physiology and primary metabolism. Shape, size and elemental composition of C–S–H seeds were also evaluated. The tests on the reference microorganisms have shown that the reaction to these nanomaterials can be specific and depends on the strain as well as the type of used nanomaterial. Furthermore, the presence of C–S–H seeds in the growth environment led to metabolic stimulation that resulted in faster growth, higher biochemical activity, and increased biofilm formation. Based on our findings, we conclude that even though C–S–H seeds have antimicrobial potential, they can be potentially used to promote the growth of selected microbial strains. This phenomenon could be further investigated towards the formation of beneficial biofilms on building materials.

3D Concrete Printing for Sustainable Construction

Despite the rapid development of 3D printing technology for cement composites, there are still a number of unsolved issues related to extrusion printing. One of them is proper mix design that allows for meeting criteria related to the printing of cementitious materials, such as pumpability, buildability, consistency on the materials, flowability and workability, simultaneously incorporating sustainable development ideas. In the case of mixes for 3D printing, the modification of the composition which increases the overall performance does not always go hand in hand with the reduction of negative environmental impact. The article presents the results of tests of eight mixtures modified with reactive and inert mineral additives designed for 3D printing. The mixes were evaluated in terms of their rheological and mechanical properties as well as environmental impact. Initial test results were verified by printing hollow columns up until collapse. Later, the differences between the compressive strength of standard samples and printed columns were determined. In order to summarize the results, a multi-faceted analysis of the properties of the mixes was carried out, introducing assessment indicators for its individual parameters. The article proves that appropriate material modification of mixes for 3D printing can significantly reduce the negative impact on the environment without hindering required 3D printing properties.

Influence of Nanoparticles from Waste Materials on Mechanical Properties, Durability and Microstructure of UHPC

This investigation presents the influence of various types of nanoparticles on the performance of ultra high performance concrete (UHPC). Three nanoparticles from waste materials include nano-crushed glass, nano-metakaolin, nano-rice husk ash were prepared using the milling technique. In addition, nano-silica prepared using chemical method at the laboratory is implemented to compare the performance. Several UHPC mixes incorporating different dosages of nanoparticles up to 5% are prepared and tested. Mechanical properties, durability as well as the microstructure of UHPC mixes have been evaluated in order to study the influence of nanoparticles on the hardened characteristics of UHPC. The experimental results showed that early strength is increased by the incorporation of nanomaterials, as compared to the reference UHPC mix. The incorporation of 3% nano-rice husk ash produced the highest compressive strength at 91 day. Microstructural measurements using Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Analysis (EDX), and Thermogravimetric Analysis (TGA) confirm the role of nanomaterials in densifying the microstructure, reducing calcium hydroxide content as well as producing more C-S-H, which improves the strength and reduces the absorption of UHPC. Nanoparticles prepared from waste materials by the milling technique are comparable to chemically prepared nanosilica in improving mechanical properties, refining the microstructure and reducing the absorption of UHPC.

Effect of Curing Methods on Shrinkage Development in 3D-Printed Concrete

Technological developments in construction have led to an increase in the use of 3D modelling using CAD environments. The popularity of this approach has increased in tandem with developments in industry branches which use 3D printers to print concrete based printing materials in construction, as these allow freedom in shaping the dimensions of supporting elements. One of the biggest challenges for researchers working on this highly innovative technology is that of cement material shrinkage. This article presents the findings of research on an original method of measuring deformations caused by shrinkage in 3D-printed concrete elements. It also discusses the results of tests on base mixes, as well as comparisons between the influence of internal and external curing methods on the development of deformations and their final outcomes. Furthermore, the article discusses differences between deformations formed after seven days of hardening without curing, with those which occur when two common, traditional concrete curing methods are used: foil insulation and shrinkage reducing admixtures. In addition, the article examines the effects of internal curing on the 1, 7, 14, 21 and 28 day mechanical properties of concrete, in accordance with EN 196-1 and EN 12390-2. Studies have shown that the optimal amount of shrinkage reducing admixtures is 4% (in relation to the mass of cement), resulting in a reduction in total shrinkage of 23%. The use of a shrinkage reducing admixture in 3D-printed concrete does not affect their strength after 28 days, but slows the strength development during the first 7 days.

The effects of seawater and nanosilica on the performance of blended cements and composites

This study investigates the effects of seawater and nanosilica (3% by weight of cement), on the fresh and hardened properties of cement pastes and mortars produced with two types of low heat cements: Portland pozzolana cement (CEM II) and blast furnace cement (CEM III). The heat of hydration, initial and final setting times, rheological properties, strength development, sorptivity and water accessible porosity of the cement pastes and mortars were determined. The data reveal that cement type has a significant effect on the reaction rate of cement with seawater and nanosilica (NS). Specimens produced with slag-blended cement exhibited a higher cement reaction rate and the composite produced exhibited better mechanical performance, as a result of the additional reaction of alumina rich phases in slag, with seawater. Replacement of freshwater with seawater contributes mostly to a significant improvement of early strength. However, in the case of slag-blended cement, 28 day strength also improved. The incorporation of NS results in additional acceleration of hydration processes, as well as to a decrease in cement setting time. In contrast, the addition of NS results in a noticeable increment in the yield-stress of pastes, with this effect being pronounced when NS is mixed along with seawater. Moreover, the use of seawater and NS has a beneficial effect on microstructure refinement, thus improving the transport properties of cement mortars. Overall, the study has showed that both seawater and NS can be successfully used to accelerate the hydration process of low heat blended cements and to improve the mechanical and transport properties of cement-based composites.

Influence of Nanosilica on Mechanical Properties, Sorptivity, and Microstructure of Lightweight Concrete

This study presents the results of an experimental investigation of the effects of nanosilica (NS) on the strength development, transport properties, thermal conductivity, air-void, and pore characteristics of lightweight aggregate concrete (LWAC), with an oven-dry density <1000 kg/m³. Four types of concrete mixtures, containing 0 wt.%, 1 wt.%, 2 wt.%, and 4 wt.% of NS were prepared. The development of flexural and compressive strengths was determined for up to 90 days of curing. In addition, transport properties and microstructural properties were determined, with the use of RapidAir, mercury intrusion porosimetry (MIP), and scanning electron microscopy (SEM) techniques. The experimental results showed that NS has remarkable effects on the mechanical and transport properties of LWACs, even in small dosages. A significant improvement in strength and a reduction of transport properties, in specimens with an increased NS content, was observed. However, the positive effects of NS were more pronounced when a higher amount was incorporated into the mixtures (>1 wt.%). NS contributed to compaction of the LWAC matrix and a modification of the air-void system, by increasing the amount of solid content and refining the fine pore structure, which translated to a noticeable improvement in mechanical and transport properties. On the other hand, NS decreased the consistency, while increasing the viscosity of the fresh mixture. An increment of superplasticizer (SP), along with a decrement of stabilizer (ST) dosages, are thus required.