Dynamic Viscoelasticity and Surface Properties of Porcine Left Anterior Descending Coronary Arteries

Frequency and time dependent viscoelastic characterization of pediatric porcine brain tissue in compression

Understanding the viscoelastic behavior of pediatric brain tissue is critical to interpret how external mechanical forces affect head injury in children. However, knowledge of the viscoelastic properties of pediatric brain tissue is limited, and this reduces the biofidelity of developed numeric simulations of the pediatric head in analysis of brain injury. Thus, it is essential to characterize the viscoelastic behavior of pediatric brain tissue in various loading conditions and to identify constitutive models. In this study, the pediatric porcine brain tissue was investigated in compression with determine the viscoelasticity under small and large strain, respectively. A range of frequencies between 0.1 and 40 Hz was applied to determine frequency-dependent viscoelastic behavior via dynamic mechanical analysis, while brain samples were divided into three strain rate groups of 0.01/s, 1/s and 10/s for compression up to 0.3 strain level and stress relaxation to obtain time-dependent viscoelastic properties. At frequencies above 20 Hz, the storage modulus did not increase, while the loss modulus increased continuously. With strain rate increasing from 0.01/s to 10/s, the mean stress at 0.1, 0.2 and 0.3 strain increased to approximate 6.8, 5.6 and 4.4 times, respectively. The brain compressive response was sensitive to strain rate and frequency. The characterization of brain tissue will be valuable for development of head protection systems and prediction of brain injury.

The design and characterisation of sinusoidal toolpaths using sub-zero bioprinting of polyvinyl alcohol

Sub-zero (°C) additive manufacturing (AM) systems present a promising solution for the fabrication of hydrogel structures with complex external geometry or a heterogeneous internal structure. Polyvinyl alcohol cryogels (PVA-C) are promising tissue-mimicking materials, with mechanical properties that can be designed to satisfy a wide variety of soft tissues. However, the design of more complex mechanical properties into additively manufactured PVA-C samples, which can be enabled using the toolpath, is a largely unstudied area. This research project will investigate the effect of toolpath variation on the elastic and viscoelastic properties of PVA-C samples fabricated using a sinusoidal toolpath. Samples were fabricated using parametric variation of a sinusoidal toolpath, whilst retaining the same overall cross-sectional area, using a sub-zero AM system. To mechanically characterise the samples, they were tested under tension in uniaxial ramp tests, and through dynamic mechanical analysis (DMA). The elastic and viscoelastic moduli of the samples are presented. No correlations between the parametric variation of the design and the Young's modulus were observed. Analysis of the data shows high intra-sample repeatability, demonstrated robust testing protocols, and variable inter-sample repeatability, indicating differences in the printability and consistency of fabrication between sample sets. DMA of the wavelength samples, show a frequency-dependent loss moduli. The storage modulus demonstrates frequency independence, and a large increase in magnitude as the sample increases to 3 wavelengths.

The effect of cyclic stretch on aortic viscoelasticity and the putative role of smooth muscle focal adhesion

Due to its viscoelastic properties, the aorta aids in dampening blood pressure pulsatility. At the level of resistance-arteries, the pulsatile flow will be transformed into a continuous flow to allow for optimal perfusion of end organs such as the kidneys and the brain. In this study, we investigated the ex vivo viscoelastic properties of different regions of the aorta of healthy C57Bl6/J adult mice as well as the interplay between (altered) cyclic stretch and viscoelasticity. We demonstrated that the viscoelastic parameters increase along the distal aorta and that the effect of altered cyclic stretch is region dependent. Increased cyclic stretch, either by increased pulse pressure or pulse frequency, resulted in decreased aortic viscoelasticity. Furthermore, we identified that the vascular smooth muscle cell (VSMC) is an important modulator of viscoelasticity, as we have shown that VSMC contraction increases viscoelastic parameters by, in part, increasing elastin fiber tortuosity. Interestingly, an acute increase in stretch amplitude reverted the changes in viscoelastic properties induced by VSMC contraction, such as a decreasing contraction-induced elastin fiber tortuosity. Finally, the effects of altered cyclic stretch and VSMC contraction on viscoelasticity were more pronounced in the abdominal infrarenal aorta, compared to both the thoracic ascending and descending aorta, and were attributed to the activity and stability of VSMC focal adhesion. Our results indicate that cyclic stretch is a modulator of aortic viscoelasticity, acting on VSMC focal adhesion. Conditions of (acute) changes in cyclic stretch amplitude and/or frequency, such as physical exercise or hypertension, can alter the viscoelastic properties of the aorta.

Biomechanical properties of the stomach: A comprehensive comparative analysis of human and porcine gastric tissue

BACKGROUND

Stomach-related disorders impose medical challenges and are associated with significant social and economic costs. The field of biomechanics is promising for understanding tissue behavior and for development of medical treatments and surgical interventions. In gastroenterology, animal models are often used when studies on humans are not possible. Often large animal models with similar anatomical characteristics (size and shape) are preferred. However, it is uncertain if stomachs from humans and large animals have similar mechanical properties. The aim of the present study is to characterize and compare hyper- and viscoelastic properties of porcine and human gastric tissue using tension and radial compression tests.

METHODS

Hyperelastic and viscoelastic properties were quantified from quasi-static ramp tests and stress relaxation tests. Tension in two directions and radial compression experiments were done on intact stomach wall samples as well as on separated mucosa and muscularis layer samples from porcine and human fundus, corpus and antrum.

RESULTS AND CONCLUSIONS

Similar hyper- and viscoelastic constitutive models can be used to describe porcine and human gastric tissue. In total, 19 constitutive parameters were compared and results showed significant variations between species. For example, for intact circumferential samples from antrum, the stiffness (a) and relaxation (τ₁) were greater for human samples than for porcine samples (p < 0.0001). The constitutive parameters were condition-, region- and layer-dependent and no distinct pattern hereof between species was found. This indicates that different parameters must be used to describe the specific situation. The present work provides insight into porcine and human gastric radial compressive and tensile hyper- and viscoelastic properties, strengthening the inter-species relation of the biomechanical properties. Constitutive relations were established that may aid development and translation of diagnostic or therapeutic devices with computational models.

Dynamic viscoelastic properties of porcine gastric tissue: Effects of loading frequency, region and direction

The gastric biomechanics influences digestive function as well as a range of topics of medical and scientific interests such as interaction between the stomach and gastric devices. Hence, the mechanical properties are essential for understanding gastric tissue and function in health and disease, and for the development of diagnostic or therapeutic devices. A key characteristic to be characterized is the time dependent mechanical tissue properties. The aim of this study was to characterize viscoelastic properties of the stomach across a frequency range. Longitudinal and circumferential stomach samples from the porcine fundus, corpus and antrum were pre-stretched 10 % and sinusoidally loaded with 10 % dynamic strain. The viscoelastic properties were assessed from 0.01 - 15 Hz using dynamic mechanical analysis. The storage moduli, loss moduli and tan δ had a significant second-order polynomial trend with increasing frequency. For the loss moduli, significant differences were observed between 0.01 and 15 Hz and between 0.05 and 15 Hz (p = 0.023 to 0.041). Significant differences were not found for storage moduli. Tan δ was frequency-independent, indicating that the two moduli varied proportionally. Fundus had significantly smaller storage moduli for longitudinal samples compared to corpus (p = 0.034) and antrum (p = 0.014) but was not significantly different for circumferential samples. Analysis of direction-dependency showed significant differences between longitudinal and circumferential samples (p = 0.002 to 0.042). The presented work provides insight into tensile viscoelastic properties of gastric tissue, which is useful for developing biomaterials, devices and computational models for device development specification calibrations.

An Electroconductive, Thermosensitive, and Injectable Chitosan/Pluronic/Gold-Decorated Cellulose Nanofiber Hydrogel as an Efficient Carrier for Regeneration of Cardiac Tissue

Myocardial infarction is a major cause of death worldwide and remains a social and healthcare burden. Injectable hydrogels with the ability to locally deliver drugs or cells to the damaged area can revolutionize the treatment of heart diseases. Herein, we formulate a thermo-responsive and injectable hydrogel based on conjugated chitosan/poloxamers for cardiac repair. To tailor the mechanical properties and electrical signal transmission, gold nanoparticles (AuNPs) with an average diameter of 50 nm were physically bonded to oxidized bacterial nanocellulose fibers (OBC) and added to the thermosensitive hydrogel at the ratio of 1% w/v. The prepared hydrogels have a porous structure with open pore channels in the range of 50−200 µm. Shear rate sweep measurements demonstrate a reversible phase transition from sol to gel with increasing temperature and a gelation time of 5 min. The hydrogels show a shear-thinning behavior with a shear modulus ranging from 1 to 12 kPa dependent on gold concentration. Electrical conductivity studies reveal that the conductance of the polymer matrix is 6 × 10−2 S/m at 75 mM Au. In vitro cytocompatibility assays by H9C2 cells show high biocompatibility (cell viability of >90% after 72 h incubation) with good cell adhesion. In conclusion, the developed nanocomposite hydrogel has great potential for use as an injectable biomaterial for cardiac tissue regeneration.

Investigation of the Compressive Viscoelastic Properties of Brain Tissue Under Time and Frequency Dependent Loading Conditions

The mechanical characterization of brain tissue has been generally analyzed in the frequency and time domain. It is crucial to understand the mechanics of the brain under realistic, dynamic conditions and convert it to enable mathematical modelling in a time domain. In this study, the compressive viscoelastic properties of brain tissue were investigated under time and frequency domains with the same physical conditions and the theory of viscoelasticity was applied to estimate the prediction of viscoelastic response in the time domain based on frequency-dependent mechanical moduli through Finite Element models. Storage and loss modulus were obtained from white and grey matter, of bovine brains, using dynamic mechanical analysis and time domain material functions were derived based on a Prony series representation. The material models were evaluated using brain testing data from stress relaxation and hysteresis in the time dependent analysis. The Finite Element models were able to represent the trend of viscoelastic characterization of brain tissue under both testing domains. The outcomes of this study contribute to a better understanding of brain tissue mechanical behaviour and demonstrate the feasibility of deriving time-domain viscoelastic parameters from frequency-dependent compressive data for biological tissue, as validated by comparing experimental tests with computational simulations.

The dynamic viscoelastic characterisation and magnetic resonance imaging of poly(vinyl alcohol) cryogel: Identifying new attributes and opportunities

Poly(vinyl alcohol) (PVA) cryogel is a biocompatible, synthetic hydrogel, compatible with magnetic resonance (MR) imaging. It is widely used as a biomaterial in tissue scaffolds and mimics to test various diagnostic techniques. The aim of this study is to characterise the effect of varying PVA concentration, molecular weight (MW) and manufacturing protocol on the viscoelastic mechanical properties and MR T₂ relaxation time. Further to this MR imaging (MRI) was investigated as a method to quantify material homogeneity. Cylindrical samples of PVA, of varying MW, concentration and number of freeze thaw cycles (FTCs), were manufactured. Dynamic mechanical analysis was performed to evaluate the storage and loss moduli between frequencies of 0.5 and 10 Hz. MR T₂ relaxation maps were imaged using a 7 T MRI instrument. Storage and loss moduli were shown to increase with MW, concentration, or the number of FTCs; with storage modulus ranging from 55 kPa to 912 kPa and loss modulus ranging from 6 kPa to 103 kPa. MR T₂ relaxation time was shown to increase linearly with PVA concentration. The qualitative and quantitative heterogeneity of the PVA sample were identified through MR T₂ relaxation time maps. Excitingly, PVA demonstrated a composition-dependent casual correlation between the viscoelastic mechanical properties and MR T₂ relaxation time. In conclusion, this research thoroughly characterised the viscoelastic mechanical properties of PVA to support its extensive use as a biomaterial, and demonstrated the use of MRI to non-invasively identify sample heterogeneity and to predict the composition-dependent viscoelastic properties of PVA.

The orthotropic viscoelastic characterisation of sub-zero 3D-printed poly(vinyl alcohol) cryogel

Abstract

Poly(vinyl alcohol) cryogel (PVA) is a versatile biomaterial used to replicate the biomechanics of tissues. Additive manufacture (AM) at sub-zero (°C) temperatures enables the manufacture of PVA with complex geometry; however, the effect of processing parameters on the mechanical properties of PVA has not been evaluated. The aim of this study is to understand the impact of print nozzle diameter and orientation on the viscoelastic mechanical properties of PVA. Samples of sub-zero AM PVA, with different filament thicknesses, were tested under tension relative to the print direction, to calculate the storage and loss moduli. As the nozzle size was decreased, AM PVA exhibited more pronounced orthotropic properties; the smallest size showed a 33% decrease in storage moduli when tested perpendicular to the print direction, as opposed to parallel. This study has demonstrated the ability of sub-zero AM to tailor the orthotropic properties of PVA.

Graphic abstract

Identifying the parameters of viscoelastic model for a gel-type material as representative of cardiac muscle in dynamic tests

In this paper, mechanical parameters of a calf heart muscle are identified and a gel-type material as the representative of the cardiac muscle in dynamic tests is introduced. The motivation of this study is to introduce a replacement material of the heart muscle to use in experimental studies of the leadless pacemaker. A particular test setup is developed to capture the experimental data based on the stress relaxation test method where its outputs are time histories of the force and displacement. The standard linear solid model is used for mathematical modeling of the heart muscle sample and a gel-type material specimen namely α-gel. Five tests with different strain history (13.6%,17.1%,20.6%22.4%and,23.8%) are performed by regarding and disregarding the influence of the initial ramp of the loading. The mechanical parameters of the standard linear solid model were identified with precise curve fitting. Consideration of the initial ramp significantly influences the consequences and they are so close to their experimental counterparts. The identified parameters of the standard linear solid model by regarding the influence of the initial ramp for the gel-type material are within an acceptable range for the viscoelastic properties of the calf heart tissue. These results show that the gel-type material has the potential to represent the cardiac muscle in the leadless pacemaker experimental studies. Dynamic mechanical analysis is used to characterize the dynamic viscoelastic properties for the gel by utilizing the identified parameters with taking into account the initial ramp in the frequency domain. Results show that Storage modulus, Loss modulus, and Loss tangent are strongly frequency-dependent especially at low-frequency around the heartbeat frequency range (0-2 Hz).

Multifaceted Design and Emerging Applications of Tissue Adhesives

Tissue adhesives can form appreciable adhesion with tissues and have found clinical use in a variety of medical settings such as wound closure, surgical sealants, regenerative medicine, and device attachment. The advantages of tissue adhesives include ease of implementation, rapid application, mitigation of tissue damage, and compatibility with minimally invasive procedures. The field of tissue adhesives is rapidly evolving, leading to tissue adhesives with superior mechanical properties and advanced functionality. Such adhesives enable new applications ranging from mobile health to cancer treatment. To provide guidelines for the rational design of tissue adhesives, here, existing strategies for tissue adhesives are synthesized into a multifaceted design, which comprises three design elements: the tissue, the adhesive surface, and the adhesive matrix. The mechanical, chemical, and biological considerations associated with each design element are reviewed. Throughout the report, the limitations of existing tissue adhesives and immediate opportunities for improvement are discussed. The recent progress of tissue adhesives in topical and implantable applications is highlighted, and then future directions toward next-generation tissue adhesives are outlined. The development of tissue adhesives will fuse disciplines and make broad impacts in engineering and medicine.

The mechanical characterization of blood vessels and their substitutes in the continuous quest for physiological-relevant performances. A critical review

During the last 50 years, novel biomaterials and tissue engineering techniques have been investigated to produce alternative vascular substitutes that recapitulate the unique elastic mechanical features of blood vessels. A large variation in mechanical characterization, including the test type, protocol, and data analysis, is present in literature which complicates the comparison among studies and prevents the blooming and the advancement of this field. In addition, a limited mechanical assessment of the substitute for the intended application is often provided. In this light, this review presents the mechanical environment of blood vessels, discusses their mechanical behavior responsible for the suited blood flow into the body (non-linearity, anisotropy, hysteresis, and compliance), and compares the mechanical properties reported in literature (obtained with compression, tensile, stress-relaxation, creep, dynamic mechanical analysis, burst pressure, and dynamic compliance tests). This perspective highlights that the mechanical properties extracted through conventional tests are not always suitable indicators of the mechanical performance during the working life of a vascular substitute. The available tests can be then strategically used at different stages of the substitute development, prioritizing the simplicity of the method at early stages, and the physiological pertinence at later stages, following as much as possible ISO standards in the field. A consistent mechanical characterization focused on the behavior to which they will be subdued during real life is one key and missing element in the quest for physiological-like mechanical performance of vascular substitutes.

Mechanical testing of glutaraldehyde cross-linked mitral valves. Part two: Elastic and viscoelastic properties of chordae tendineae

The aim of this study was to assess whether the mechanical properties of mitral valve chordae tendineae are sensitive to being cross-linked under load. A total 64 chordae were extracted from eight porcine hearts. Two chordae (posterior basal) from each heart were subjected to uniaxial ramp testing and six chordae (two strut, two anterior basal and two posterior basal) were subjected to dynamic mechanical analysis over frequencies between 0.5 and 10 Hz. Chordae were either cross-linked in tension or cross-linked in the absence of loading. Chordae cross-linked under load transitioned from high to low extension at a lower strain than cross-linked unloaded chordae (0.07 cf. 0.22), with greater pre-transitional (30.8 MPa cf. 5.78 MPa) and post-transitional (139 MPa cf. 74.1 MPa) moduli. The mean storage modulus of anterior strut chordae ranged from 48 to 54 MPa for cross-linked unloaded chordae, as compared to 53-61 MPa cross-linked loaded chordae. The mean loss modulus of anterior strut chordae ranged from 2.3 to 2.9 MPa for cross-linked unloaded chordae, as compared to 3.8-4.8 MPa cross-linked loaded chordae. The elastic and viscoelastic properties of chordae following glutaraldehyde cross-linking are dependent on the inclusion/exclusion of loading during the cross-linking process; with loading increasing the magnitude of the material properties measured.

Mechanical testing of glutaraldehyde cross-linked mitral valves. Part one: In vitro mechanical behaviour

The aim of this study was to perform an initial assessment, in vitro, of the feasibility of using a glutaraldehyde cross-linked porcine mitral valve to retain acute functionality, focusing on assessing mitral regurgitation. Six porcine hearts were tested using an in vitro simulator. Testing was repeated following cross-linking of mitral valves; where cross-linking was achieved by placing them in a glutaraldehyde solution. The simulator enabled systolic pressure on the ventricular side of the valve to be mimicked. Following testing, mitral valve leaflets underwent Scanning Electron Microscopy of the ventricular surface of both the anterior and posterior leaflets (1 cm² samples). The peak pressure withstood by cross-linked valves was significantly lower than for untreated valves (108 mmHg cf. 128 mmHg for untreated valves; p  < 0.05). The peak pressure was typically reached 0.5 s later than for the untreated valve. While both cross-linked and untreated valves exhibited endothelium denudation, the unfixed valve had less endothelial loss. Glutaraldehyde cross-linking of porcine mitral valves may be of potential value in assessing improved bioprosthetic mitral valve replacements. However, a more immobile valve exhibiting endothelial denudation (i.e. sclerosis) was a possible concerns identified following in vitro acute assessment.

Experimental Studies of the Influence of Dynamic Loading on the Elastic Properties of Sandstone

Under dynamic loading, the geomechanical properties of porous clastic rocks differ from those in quasistatic loading. A small experimental rig was built to directly assess the influence of vibrations on the uniaxial compressive strength (UCS), Young modulus, and Poisson’s ratio. A piezoelectric actuator powered by a signal from an oscillator was used in the rig as a generator of vibrations. A laser sensor and eddy current probe measured the longitudinal and transverse deformation. Tinius Hounsfield and Instron Series 4483 installations were used to determine the geomechanical properties of new red sandstone in a quasistatic regime. The boundaries of elastic deformations determined in the quasistatic loading were implemented in the dynamic loading. To perform the experiments in the elastic zone (on the graph of stress (σ)–strain (ε)), small samples with diameters ranging between 7.5 and 24.7 mm were manufactured. The investigation demonstrated that the Young’s modulus of the sandstone increased with increasing values of the dynamic load and frequency.

Dynamic mechanical characterization and viscoelastic modeling of bovine brain tissue

Brain tissue is vulnerable and sensitive, predisposed to potential damage under various conditions of mechanical loading. Although its material properties have been investigated extensively, the frequency-dependent viscoelastic characterization is currently limited. Computational models can provide a non-invasive method by which to analyze brain injuries and predict the mechanical response of the tissue. The brain injuries are expected to be induced by dynamic loading, mostly in compression and measurement of dynamic viscoelastic properties are essential to improve the accuracy and variety of finite element simulations on brain tissue. Thus, the aim of this study was to investigate the compressive frequency-dependent properties of brain tissue and present a mathematical model in the frequency domain to capture the tissue behavior based on experimental results. Bovine brain specimens, obtained from four locations of corona radiata, corpus callosum, basal ganglia and cortex, were tested under compression using dynamic mechanical analysis over a range of frequencies between 0.5 and 35 Hz to characterize the regional and directional response of the tissue. The compressive dynamic properties of bovine brain tissue were heterogenous for regions but not sensitive to orientation showing frequency dependent statistical results, with viscoelastic properties increasing with frequency. The mean storage and loss modulus were found to be 12.41 kPa and 5.54 kPa, respectively. The material parameters were obtained using the linear viscoelastic model in the frequency domain and the numeric simulation can capture the compressive mechanical behavior of bovine brain tissue across a range of frequencies. The frequency-dependent viscoelastic characterization of brain tissue will improve the fidelity of the computational models of the head and provide essential information to the prediction and analysis of brain injuries in clinical treatments.

Assessment of surface roughness and blood rheology on local coronary haemodynamics: a multi-scale computational fluid dynamics study

The surface roughness of the coronary artery is associated with the onset of atherosclerosis. The study applies, for the first time, the micro-scale variation of the artery surface to a 3D coronary model, investigating the impact on haemodynamic parameters which are indicators for atherosclerosis. The surface roughness of porcine coronary arteries have been detailed based on optical microscopy and implemented into a cylindrical section of coronary artery. Several approaches to rheology are compared to determine the benefits/limitations of both single and multiphase models for multi-scale geometry. Haemodynamic parameters averaged over the rough/smooth sections are similar; however, the rough surface experiences a much wider range, with maximum wall shear stress greater than 6 Pa compared to the approximately 3 Pa on the smooth segment. This suggests the smooth-walled assumption may neglect important near-wall haemodynamics. While rheological models lack sufficient definition to truly encompass the micro-scale effects occurring over the rough surface, single-phase models (Newtonian and non-Newtonian) provide numerically stable and comparable results to other coronary simulations. Multiphase models allow for phase interactions between plasma and red blood cells which is more suited to such multi-scale models. These models require additional physical laws to govern advection/aggregation of particulates in the near-wall region.

The role of strut chordae in mitral valve competence during annular dilation

Strut chordae, on their own, are not typically thought to aid mitral valve competence. The aim of this study is to assess whether strut chordae aid mitral valve competence during acute annular dilation. Twelve porcine hearts were dissected and tested using an in vitro simulator, with the mitral annulus tested in either a 'normal' or a dilated configuration. The normal configuration included a diameter of 30 mm, a posterior leaflet 'radius' of 15 mm and a commissural corner 'radius' of 7.5 mm; the dilated annular template instead used dimensions of 50 mm, 25 mm and 12.5 mm, respectively. Each mitral valve underwent ten repeat tests with a target systolic pressure of 100 mmHg. No significant difference in the pressure was detected between the dilated and regular annuli for the mitral valves tested (95 ± 3 mmHg cf. 95 ± 2 mmHg). However, the volume of regurgitation for a dilated annulus was 28 ml greater than for a valve with a normal annulus. Following severing of strut chordae, there was a significant reduction in the systolic pressure withstood before regurgitation by mitral valves with dilated annuli (60 ± 29 mmHg cf. 95 ± 2 mmHg for normal annular dimensions; p < 0.05). In conclusion, strut chordae tendineae may play a role in aiding mitral valve competence during pathophysiology.

The role of strut chordae in mitral valve competence during annular dilation

Strut chordae, on their own, are not typically thought to aid mitral valve competence. The aim of this study is to assess whether strut chordae aid mitral valve competence during acute annular dilation. Twelve porcine hearts were dissected and tested using an in vitro simulator, with the mitral annulus tested in either a 'normal' or a dilated configuration. The normal configuration included a diameter of 30 mm, a posterior leaflet 'radius' of 15 mm and a commissural corner 'radius' of 7.5 mm; the dilated annular template instead used dimensions of 50 mm, 25 mm and 12.5 mm, respectively. Each mitral valve underwent ten repeat tests with a target systolic pressure of 100 mmHg. No significant difference in the pressure was detected between the dilated and regular annuli for the mitral valves tested (95 ± 3 mmHg cf. 95 ± 2 mmHg). However, the volume of regurgitation for a dilated annulus was 28 ml greater than for a valve with a normal annulus. Following severing of strut chordae, there was a significant reduction in the systolic pressure withstood before regurgitation by mitral valves with dilated annuli (60 ± 29 mmHg cf. 95 ± 2 mmHg for normal annular dimensions; p < 0.05). In conclusion, strut chordae tendineae may play a role in aiding mitral valve competence during pathophysiology.

A Finite Element Model for Trigger Finger

The aim of this study was to develop a finite element model to investigate the forces on tendons which ensue due to trigger finger. The model was used to simulate both flexor and extensor tendons within the index finger; two test cases were defined, simulating a “mildly” and “severely” affected tendon by applying constraints. The finger was simulated in three different directions: extension, abduction and hyper-extension. There was increased tension during hyper-extension, with tension in the mildly affected tendon increasing from 1.54 to 2.67 N. Furthermore, there was a consistent relationship between force and displacement, with a substantial change in the gradient of the force when the constraints of the condition were applied for all movements. The intention of this study is that the simulation framework is used to enable the in silico development of novel prosthetic devices to aid with treatment of trigger finger, given that, currently, the non-surgical first line of treatment is a splint.

Frequency-related viscoelastic properties of the human incisor periodontal ligament under dynamic compressive loading

Studies concerning the mechanical properties of the human periodontal ligament under dynamic compression are rare. This study aimed to determine the viscoelastic properties of the human periodontal ligament under dynamic compressive loading. Ten human incisor specimens containing 5 maxillary central incisors and 5 maxillary lateral incisors were used in a dynamic mechanical analysis. Frequency sweep tests were performed under the selected frequencies between 0.05 Hz and 5 Hz with a compression amplitude that was 2% of the PDL's initial width. The compressive strain varied over a range of 4%-8% of the PDL's initial width. The storage modulus, ranging from 28.61 MPa to 250.21 MPa, increased with the increase in frequency. The loss modulus (from 6.00 MPa to 49.28 MPa) also increased with frequency from 0.05 Hz- 0.5 Hz but remained constant when the frequency was higher than 0.5 Hz. The tanδ showed a negative logarithmic correlation with frequency. The dynamic moduli and the loss tangent of the central incisor were higher than those of the lateral incisor. This study concluded that the human PDL exhibits viscoelastic behavior under compressive loadings within the range of the used frequency, 0.05 Hz- 5 Hz. The tooth position and testing frequency may have effects on the viscoelastic properties of PDL.

Zirconia implants with improved attachment to the gingival tissue

BACKGROUND

Gingival tissue attachment is known to be important for long-term prognosis of implants. This in vitro study evaluated the gingival attachment to zirconia implants and zirconia implants modified with sol-gel derived TiO₂ coatings.

METHODS

Zirconia endodontic posts (n = 23) were used to function as implants that were inserted into the center of full-thickness porcine gingival explants (n = 31). The tissue/implant specimens were then individually placed at an air/liquid interface on a stainless-steel grid in cell culture wells containing a nutrient solution. The tissue cultures were incubated at 37°C in a 5% CO₂ environment and at days 7 and 14, the specimens were harvested and analyzed by dynamic mechanical analysis (DMA) measurements under dynamic loading conditions mimicking natural mastication. Specimens were also analyzed by immunohistochemical staining identifying the laminin (Ln) γ2 chain specific for Ln-332, which is known to be a crucial molecule for the proper attachment of epithelium to tooth/implant surface.

RESULTS

Tissue attachment to TiO₂ -coated zirconia demonstrated higher dynamic modulus of elasticity and higher creep modulus, meaning that the attachment is stronger and more resistant to damage during function over time. Laminin γ2 was identified in the attachment of epithelium to TiO₂ -coated zirconia.

CONCLUSIONS

Both DMA and histological analysis support each other, so the gingival tissue is more strongly attached to sol-gel derived TiO₂ -coated zirconia than uncoated zirconia. Immunohistochemical staining showed that TiO₂ coating may enhance the synthesis and deposition of Ln-332 in the epithelial attachment to the implant surface.

The status and challenges of replicating the mechanical properties of connective tissues using additive manufacturing

The ability to fabricate complex structures via precise and heterogeneous deposition of biomaterials makes additive manufacturing (AM) a leading technology in the creation of implants and tissue engineered scaffolds. Connective tissues (CTs) remain attractive targets for manufacturing due to their "simple" tissue compositions that, in theory, are replicable through choice of biomaterial(s) and implant microarchitecture. Nevertheless, characterisation of the mechanical and biological functions of 3D printed constructs with respect to their host tissues is often limited and remains a restriction towards their translation into clinical practice. This review aims to provide an update on the current status of AM to mimic the mechanical properties of CTs, with focus on arterial tissue, articular cartilage and bone, from the perspective of printing platforms, biomaterial properties, and topological design. Furthermore, the grand challenges associated with the AM of CT replacements and their subsequent regulatory requirements are discussed to aid further development of reliable and effective implants.

Investigating the Effects of Mechanical Stimulation on Retinal Ganglion Cell Spontaneous Spiking Activity

Mechanical forces are increasingly recognized as major regulators of several physiological processes at both the molecular and cellular level; therefore, a deep understanding of the sensing of these forces and their conversion into electrical signals are essential for studying the mechanosensitive properties of soft biological tissues. To contribute to this field, we present a dual-purpose device able to mechanically stimulate retinal tissue and to record the spiking activity of retinal ganglion cells (RGCs). This new instrument relies on combining ferrule-top micro-indentation, which provides local measurements of viscoelasticity, with high-density multi-electrode array (HD-MEAs) to simultaneously record the spontaneous activity of the retina. In this paper, we introduce this instrument, describe its technical characteristics, and present a proof-of-concept experiment that shows how RGC spiking activity of explanted mice retinas respond to mechanical micro-stimulations of their photoreceptor layer. The data suggest that, under specific conditions of indentation, the retina perceive the mechanical stimulation as modulation of the visual input, besides the longer time-scale of activation, and the increase in spiking activity is not only localized under the indentation probe, but it propagates across the retinal tissue.

Multiscale three-dimensional surface reconstruction and surface roughness of porcine left anterior descending coronary arteries

The aim of this study was to investigate the multiscale surface roughness characteristics of coronary arteries, to aid in the development of novel biomaterials and bioinspired medical devices. Porcine left anterior descending coronary arteries were dissected ex vivo, and specimens were chemically fixed and dehydrated for testing. Surface roughness was calculated from three-dimensional reconstructed surface images obtained by optical, scanning electron and atomic force microscopy, ranging in magnification from 10× to 5500×. Circumferential surface roughness decreased with magnification, and microscopy type was found to influence surface roughness values. Longitudinal surface roughness was not affected by magnification or microscopy types within the parameters of this study. This study found that coronary arteries exhibit multiscale characteristics. It also highlights the importance of ensuring consistent microscopy parameters to provide comparable surface roughness values.

Validated model of platelet slip at stenosis and device surfaces

Platelets are central to thrombosis. However, it is unknown whether platelets slip at vascular or device surfaces. The presence of platelet slip at a surface would interrupt physical contact between the platelet and that surface, and therefore diminish adhesion and thrombosis. Unfortunately, no existing technology can directly measure platelet slip in a biological environment. The objective of this study was to explore whether microspheres-modeling platelets-slip at different vascular and device surfaces in an acrylic scaled-up model coronary artery. The microspheres (3.12 µm diameter) were suspended in a transparent glycerol/water experimental fluid, which flowed continuously at Reynolds numbers typical of coronary flow (200-400) through the model artery. We placed a series of axisymmetric acrylic stenoses (cross-sectional area reduction [CSAr], 20-90%) into the model artery, both without and with a central cylinder present (modeling a percutaneous interventional guide wire, and with a scaled-up Doppler catheter mounted upstream). We used laser Doppler velocimetry (LDV) to measure microsphere velocities within, proximal and distal to each stenosis, and compared to computer simulations of fluid flow with no-slip. For validation, we replaced the acrylic with paraffin stenoses (more biologically relevant from a surface roughness perspective) and then analyzed the signal recorded by the scaled-up Doppler catheter. Using the LDV, we identified progressive microsphere slip proportional to CSAr inside entrances for stenoses ≥60% and ≥40% without and with cylinder present, respectively. Additionally, microsphere slip occurred universally along the cylinder surface. Computer simulations indicated increased fluid shear rates (velocity gradients) at these particular locations, and logistic regression analysis comparing microsphere slip with fluid shear rate resulted in a c-index of 0.989 at a cut-point fluid shear rate of (10.61 [cm^-1]×mean velocity [cm×sec^-1]). Moreover, the presence of the cylinder caused disordering of microsphere shear rates distal to higher grade stenoses, indicating a disturbance in their flow. Finally, despite lower precision, the signal recorded by the scaled-up Doppler catheter nonetheless indicated slip at the entry into and at most locations distal to the 90% stenosis. Our validated model establishes proof of concept for platelet slip, and platelet slip explains several important basic and clinical observations. If technological advances allow confirmation in a true biologic environment, then our results will likely influence the development of shear-dependent antiplatelet drugs. Also, adding shear rate information, our results provide a direct experimental fluid dynamic foundation for antiplatelet-focused antithrombotic therapy during coronary interventions directed towards higher grade atherosclerotic stenoses.

The Effect of Mechanical Overloading on Surface Roughness of the Coronary Arteries

Background

Surface roughness can be used to identify disease within biological tissues. Quantifying surface roughness in the coronary arteries aids in developing treatments for coronary heart disease. This study investigates the effect of extreme physiological loading on surface roughness, for example, due to a rupture of an artery.

Methods

The porcine left anterior descending (LAD) coronary arteries were dissected ex vivo. Mechanical overloading was applied to the arteries in the longitudinal direction to simulate extreme physiological loading. Surface roughness was calculated from three-dimensional reconstructed images. Surface roughness was measured before and after damage and after chemical processing to dehydrate tissue specimens.

Results

Control specimens confirmed that dehydration alone results in an increase of surface roughness in the circumferential direction only. No variation was noted between the hydrated healthy and damaged specimens, in both the longitudinal (0.91 ± 0.26 and 1.05 ± 0.25 μm) and circumferential (1.46 ± 0.38 and 1.47 ± 0.39 μm) directions. After dehydration, an increase in surface roughness was noted for damaged specimens in both the longitudinal (1.28 ± 0.33 μm) and circumferential (1.95 ± 0.56 μm) directions.

Conclusions

Mechanical overloading applied in the longitudinal direction did not significantly affect surface roughness. However, when combined with chemical processing, a significant increase in surface roughness was noted in both the circumferential and longitudinal directions. Mechanical overloading causes damage to the internal constituents of the arteries, which is significantly noticeable after dehydration of tissue.

Effect of glutaraldehyde based cross-linking on the viscoelasticity of mitral valve basal chordae tendineae

BACKGROUND

Mitral valve failure can require repair or replacement. Replacement bioprosthetic valves are treated with glutaraldehyde prior to implantation. The aim of this study was to determine the changes in mechanical properties following glutaraldehyde fixation of mitral valve chordae.

METHODS

To investigate the impact of glutaraldehyde on mitral valve chordae, 24 basal chordae were dissected from four porcine hearts. Anterior and posterior basal (including strut) chordae were used. All 24 chordae were subjected to a sinusoidally varying load (mean level 2N, dynamic amplitude 2N) over a frequency range of 0.5-10 Hz before and after glutaraldehyde treatment.

RESULTS

The storage and loss modulus of all chordal types decreased following glutaraldehyde fixation. The storage modulus ranged from: 108 to 119 MPa before fixation and 67.3-87.4 MPa following fixation for basal chordae; 52.3-58.4 MPa before fixation and 47.9-53.5 MPa following fixation for strut chordae. Similarly, the loss modulus ranged from: 5.47 to 6.25 MPa before fixation and 3.63-4.94 MPa following fixation for basal chordae; 2.60-2.97 MPa before fixation and 2.31-2.93 MPa following fixation for strut chordae.

CONCLUSION

The viscoelastic properties of mitral valve chordae are affected by glutaraldehyde fixation; in particular, the reduction in storage moduli decreased with an increase in chordal diameter.

Towards Additive Manufacture of Functional, Spline-Based Morphometric Models of Healthy and Diseased Coronary Arteries: In Vitro Proof-of-Concept Using a Porcine Template

The aim of this study is to assess the additive manufacture of morphometric models of healthy and diseased coronary arteries. Using a dissected porcine coronary artery, a model was developed with the use of computer aided engineering, with splines used to design arteries in health and disease. The model was altered to demonstrate four cases of stenosis displaying varying severity, based on published morphometric data available. Both an Objet Eden 250 printer and a Solidscape 3Z Pro printer were used in this analysis. A wax printed model was set into a flexible thermoplastic and was valuable for experimental testing with helical flow patterns observed in healthy models, dominating the distal LAD (left anterior descending) and left circumflex arteries. Recirculation zones were detected in all models, but were visibly larger in the stenosed cases. Resin models provide useful analytical tools for understanding the spatial relationships of blood vessels, and could be applied to preoperative planning techniques, but were not suitable for physical testing. In conclusion, it is feasible to develop blood vessel models enabling experimental work; further, through additive manufacture of bio-compatible materials, there is the possibility of manufacturing customized replacement arteries.

Viscoelastic properties of multi-layered cellularized vascular tissues fabricated from collagen gel

Since collagen is one of the major extracellular matrix components in vascular tissues, its use for vascular tissue engineering has several advantages. However, collagen extraction and processing for tissue engineering application alters its structure. As a result, collagen-based vascular constructs show poor mechanical properties compared to native tissues. In this work, multi-layer (single, double, and triple) vascular tissue constructs were engineered from porcine smooth muscle cells (PSMCs) entrapped in collagen gel by concentrically and sequentially layering after compaction of the previous layer(s). The engineered tissues were matured for either 14 or 21 days to allow the collagen gel to remodel before viscoelasticity, compliance, histological, and protein expression studies were conducted. While there was no significant difference upon addition of the different layers on the elastic modulus (p > .05), the viscous modulus of the single layer construct was significantly lower than the double and triple layer constructs (p < .05). Increasing the number of layers of the cellularized collagen construct increased the wall thickness and the viscous modulus of the construct. Furthermore, the cellularized single-layer construct had a relatively high compliance, but the double and triple layer constructs had compliance values comparable to both engineered vessels and native vessels. PSMCs were uniformly distributed throughout the cross-section and expressed the anticipated marker proteins smooth muscle-α actin, calponin, and smooth muscle myosin heavy chain. Taken together, this study demonstrated the viscoelastic responsiveness of multi-layer collagen-gel based vascular tissues.

Formulation and viscoelasticity of mineralised hydrogels for use in bone-cartilage interfacial reconstruction

Articular cartilage is a viscoelastic tissue whose structural integrity is important in maintaining joint health. To restore the functionality of osteoarthritic joints it is vital that regenerative strategies mimic the dynamic loading response of cartilage and bone. Here, a rotating simplex model was employed to optimise the composition of agarose and gellan hydrogel constructs structured with hydroxyapatite (HA) with the aim of obtaining composites mechanically comparable to human cartilage in terms of their ability to dissipate energy. Addition of ceramic particles was found to reinforce both matrices up to a critical concentration (< 3w/v%). Beyond this, larger agglomerates were formed, as evidenced by micro computed tomography data, which acted as stress risers and reduced the ability of composites to dissipate energy demonstrated by a reduction in tan δ values. A maximum compressive modulus of 450.7±24.9 kPa was achieved with a composition of 5.8w/v% agarose and 0.5w/v% HA. Interestingly, when loaded dynamically (1-20Hz) this optimised formulation did not exhibit the highest complex modulus instead a sample with a higher concentration of mineral was identified (5.8w/v% agarose and 25w/v% HA). Thus, demonstrating the importance of examining the mechanical behaviour of biomaterials under conditions representative of physiological environments. While the complex moduli of the optimised gellan (1.0 ± 0.2MPa at 1Hz) and agarose (1.7 ± 0.2MPa at 1Hz) constructs did not match the complex moduli of healthy human cartilage samples (26.3 ± 6.5MPa at 1Hz), similar tan δ values were observed between 1 and 5Hz. This is promising since these frequencies represent the typical heel strike time of the general population. In summary, this study demonstrates the importance of considering more than just the strength of biomaterials since tissues like cartilage play a more complex role.

Viscoelasticity of articular cartilage: Analysing the effect of induced stress and the restraint of bone in a dynamic environment

The aim of this study was to determine the effect of the induced stress and restraint provided by the underlying bone on the frequency-dependent storage and loss stiffness (for bone restraint) or modulus (for induced stress) of articular cartilage, which characterise its viscoelasticity. Dynamic mechanical analysis has been used to determine the frequency-dependent viscoelastic properties of bovine femoral and humeral head articular cartilage. A sinusoidal load was applied to the specimens and out-of-phase displacement response was measured to determine the phase angle, the storage and loss stiffness or modulus. As induced stress increased, the storage modulus significantly increased (p < 0.05). The phase angle decreased significantly (p < 0.05) as the induced stress increased; reducing from 13.1° to 3.5°. The median storage stiffness ranged from 548N/mm to 707N/mm for cartilage tested on-bone and 544N/mm to 732N/mm for cartilage tested off-bone. On-bone articular cartilage loss stiffness was frequency independent (p > 0.05); however, off-bone, articular cartilage loss stiffness demonstrated a logarithmic frequency-dependency (p < 0.05). In conclusion, the frequency-dependent trends of storage and loss moduli of articular cartilage are dependent on the induced stress, while the restraint provided by the underlying bone removes the frequency-dependency of the loss stiffness.

Viscoelastic properties of mitral valve leaflets: An analysis of regional variation and frequency-dependency

The aim of this study was to determine the regional variation in viscoelastic properties of mitral valve leaflets over a range of physiological and patho-physiological frequencies. This included comparisons to be made between anterior and posterior leaflets, anterior leaflet clear and rough zones, and radial and circumferential leaflet orientation. Dynamic mechanical analysis was used to determine frequency-dependent viscoelastic properties. The valve leaflets were dissected from eight porcine hearts. The leaflets were loaded under a sinusoidal tensile displacement, with a mean dynamic peak to trough strain of 11%, applied to all leaflet samples at nine different frequencies, ranging from 0.5 to 10 Hz. The anterior leaflet has higher storage and loss stiffness than the posterior leaflet. The storage stiffness of circumferential tissue is greater than that of radially oriented valve tissue (2.0 ± 1.6 N/mm cf. 1.7 ± 0.9 N/mm; p < 0.05); however, the loss stiffness is greater for radial tissue (0.15 ± 0.07 cf. 0.14 ± 0.09 N/mm; p < 0.05). Likewise, the storage stiffness of the anterior leaflet clear zone is greater than that of the rough zone (2.4 ± 1.6 cf. 2.1 ± 1.2; p < 0.05), but the loss stiffness is greater for the rough zone (0.17 ± 0.09 N/mm cf. 0.14 ± 0.08 N/mm; p < 0.05). In conclusion, the viscoelastic properties of porcine mitral valve leaflets have regional variations, with dynamic stiffness being dependent on circumferential or radial orientation and on location at a clear or rough zones.

Effects of freezing, fixation and dehydration on surface roughness properties of porcine left anterior descending coronary arteries

BACKGROUND

To allow measurements of surface roughness to be made of coronary arteries using various imaging techniques, chemical processing, such as fixation and dehydration, is commonly used. Standard protocols suggest storing fresh biological tissue at -40°C. The aim of this study was to quantify the changes caused by freezing and chemical processing to the surface roughness measurements of coronary arteries, and to determine whether correction factors are needed for surface roughness measurements of coronary arteries following chemical processes typically used before imaging these arteries.

METHODS

Porcine left anterior descending coronary arteries were dissected ex vivo. Surface roughness was then calculated following three-dimensional reconstruction of surface images obtained using an optical microscope. Surface roughness was measured before and after a freeze cycle to assess changes during freezing, after chemical fixation, and again after dehydration, to determine changes during these steps of chemical processing.

RESULTS

No significant difference was caused due to the freeze cycle (p>0.05). There was no significant difference in the longitudinally measured surface roughness (Ra_L=0.99±0.39μm; p>0.05) of coronary arteries following fixation and dehydration either. However, the circumferentially measured surface roughness increased significantly following a combined method of processing (Ra_C=1.36±0.40, compared 1.98±0.27μm, respectively; p<0.05). A correction factor can compensate for the change Ra_Cβ=Ra_C1+0.46in Ra_C due to processing of tissue, Where Ra_Cβ, the corrected Ra_C, had a mean of 1.31±0.21μm.

CONCLUSIONS

Independently, freezing, fixation and dehydration do not alter the surface roughness of coronary arteries. Combined, however, fixation and dehydration significantly increase the circumferential, but not longitudinal, surface roughness of coronary arteries.