An extensive review on chromium (vi) removal using natural and agricultural wastes materials as alternative biosorbents

Effective removal of chromium by adsorption using Delonix regia bark derived activated carbon from aqueous solution: a sustainable approach

This study introduces a new biosorbent derived from Delonix regia bark-activated carbon to efficiently remove Chromium Cr(VI) metal ions from aqueous systems. The biosorbent was synthesized from the bark powder of the plant species and chemically activated with phosphoric acid. The biosorbent was characterized using FTIR, SEM, and BET to determine its functional properties and structural morphology. The batch adsorption experiments examined the optimal conditions for Cr(VI) metal ion adsorption, identifying that the highest removal efficiency occurred at pH levels of 2. The ideal adsorbent dosage was determined to be 2.5 g/L, with equilibrium achieved at a contact time of 60 min at the optimal temperature of about 303 K for a Cr(VI) metal ion concentration of 20 mg/L. Various isotherm models were applied to the adsorption equilibrium values, revealing that the adsorbent had a maximum removal capacity of approximately 224.8 mg/g for Cr(VI) metal ions. The adsorption process of Cr(VI) on the DAC biosorbent was best described by the Freundlich isotherm, indicating multilayer adsorption. The kinetic data fit well with the pseudo-second-order model. Thermodynamic parameters suggested that the adsorption process was spontaneous, exothermic, and feasible across different temperatures. Furthermore, the desorption studies showed that the DAC biosorbent can easily be rejuvenated and utilized several cycles with high adsorption capacity. These findings indicate that the developed adsorbent is environmentally friendly and effective for removing Cr(VI) from water systems.

Uranium capture from aqueous solution using palm-waste based activated carbon: sorption kinetics and equilibrium

Carbonaceous materials produced from agricultural waste (palm kernel shell) by pyrolysis can be a proper type of low-cost adsorbent for wide uses in radioactive effluent treatment. In this context, the as-produced bio-char (labeled as PBC) and its sub-driven sulfuric acid and zinc oxide activated carbons (labeled as PBC-SA, and PBC-Zn respectively) were employed as adsorbents for uranium sorption from aqueous solution. Various analytical techniques, including SEM (Scanning Electron Microscopy), EXD (X-ray Diffraction), BET (Brunauer-Emmett-Teller), FTIR (Fourier Transform Infrared Spectroscopy), and Zeta potential, provide insights into the material characteristics. Kinetic and isotherm investigations illuminated that the sorption process using the three sorbents is nicely fitted with Pseudo-second-order-kinetic and Langmuir isotherm models. The picked data display that the equilibrium time was 60 min, and the maximum sorption capacity was 9.89, 16.8, and 21.9 mg/g for PBC, PBC-SA, and PBC-Zn respectively, which reflects the highest affinity for zinc oxide, activated bio-char, among the three adsorbents, for uranium taking out from radioactive wastewater. Sorption thermodynamics declare that the sorption of U(VI) is an exothermic, spontaneous, and feasible process. About 92% of the uranium-loaded PBC-Zn sorbent was eluted using 1.0 M CH3COONa sodium ethanoate solution, and the sorbent demonstrated proper stability for 5 consecutive sorption/desorption cycles.

A novel chitosan-alginate@Fe/Mn mixed oxide nanocomposite for highly efficient removal of Cr (VI) from wastewater: Experiment and adsorption mechanism

In this study, the synthesis and experimental theoretical evaluation of a new chitosan/alginate/hydrozyapatite nanocomposite doped with Mn2 and Fe2O3 for Cr removal was reported. The physicochemical properties of the obtained materials were analyzed using the following methods: SEM-EDX, XRD, FTIR, XPS, pH drift measurements, and thermal analysis. The adsorption properties were estimated based on equilibrium and adsorption kinetics measurements. The Langmuir, Freundlich and Temkin isotherms were applied to analyze the equilibrium data. The thermodynamic analysis of adsorption isotherms was performed. A number of equations and kinetic models were used to describe the adsorption rate data, including pseudo-first (PFOE) and pseudo-second (PSOE) order kinetic equations. The obtained test results show that the synthesized biomaterial, compared to pure chitosan, is characterized by greater resistance to high temperatures. Moreover, this biomaterial had excellent adsorption properties. For the adsorption of Cr (VI), the equilibrium state was reached after 120 min, and the sorption capacity was 455.9 mg/g. In addition, DFT calculations and NCI analyses were performed to get more light on the adsorption mechanism of Cr (VI) on the prepared biocomposite.

Cost-effective removal of Cr(VI) ions from aqueous media using L-cysteine functionalized gold nanoparticles embedded in melamine-based covalent organic framework (Cys-AuNPs@COF)

Due to the growing concern about the environmental effects of heavy metals, researchers are developing materials that possess high absorption capacity in addition to selectivity and high absorption speed. Recently, covalent organic frameworks (COFs) have been considered as emerging and promising adsorbents for the removal of many types of pollutants. In this work, a novel and selective adsorbent (Cys-AuNPs@COF) was prepared by embedding gold nanoparticles functionalized with L-cysteine in melamine-based COF for the removal of Cr(VI) ions from wastewater. The synthesized Cys-AuNPs@COF were characterizedby Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction analysis (XRD), Field emission scanning electron microscopy (FESEM), Energy-dispersive X-ray spectroscopy (EDX), Thermo-gravimetric analysis (TGA), and elemental mapping (EMA) analysis. The removal of Cr(VI) ions was performed using a batch mode process by taking advantage of response surface methodology (RSM) based on a central composite design (CCD) model. The maximum adsorption capacity of Cys-AuNPs@COF was 151.5 mg g-1. The experimental results followed the Langmuir model and showed pseudo-second-order kinetics. A portable, low-cost, and highly sensitive device with a smartphone colorimeter platform was developed for in situ measurement of trace amounts of chromium (VI) ions. Due to its simplicity and versatility, this method has the potential to serve as an alternative to conventional field analysis methods.

Efficient, fast, simple, and eco-friendly methods for separation of toxic chromium(VI) ions based on ion exchangers and polymer materials impregnated with Cyphos IL 101, Cyphos IL 104, or D2EHPA

In this study, we present the results of the first comparison of the elimination of toxic Cr(VI) ions, which are hazardous contamination of the environment, from aqueous solutions using ion exchangers (IEs) and polymer materials (PMs) impregnated with D2EHPA or ionic liquids (Cyphos IL 101 and Cyphos IL 104). Sorption of Cr(VI) ions and desorption from the formulated sorption materials were carried out. In comparison, classical solvent extraction was accomplished. Fourier transform infrared-attenuated total reflectance spectroscopy (FTIR-ATR), scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), and atomic force microscopy (AFM) have been used for characterization of the structure of developed IEs and PMs. The highest efficiency of adsorption of Cr(VI) ions was obtained using PMs with ionic liquids (>82%). Desorption from these materials were also very efficient (>75%). On the contrary, the application of IEs allowed for obtaining the best results of both, sorption and desorption processes when using D2EHPA (75% and 72%, respectively). The application of PMs and IEs is part of the green chemistry, and the conducted elimination of chromium(VI) ions using developed materials allows for the conclusion that they can potentially be used on a larger scale, e.g., for the treatment of industrial wastewater rich in Cr(VI) ions.

Chromium Recovery from Chromium-Loaded Cupressus lusitanica Bark in Two-Stage Desorption Processes

Hexavalent chromium (Cr(VI)) contamination poses serious health and environmental risks. Chromium biosorption has been employed as an effective means of eradicating Cr(VI) contamination. However, research on chromium desorption from chromium-loaded biosorbents is scarce despite its importance in facilitating industrial-scale chromium biosorption. In this study, single- and two-stage chromium desorption from chromium-loaded Cupressus lusitanica bark (CLB) was conducted. Thirty eluent solutions were evaluated first; the highest single-stage chromium desorption efficiencies were achieved when eluent solutions of 0.5 M NaOH, 0.5 M H2SO4, and 0.5 M H2C2O4 were used. Subsequently, two-stage kinetic studies of chromium desorption were performed. The results revealed that using 0.5 M NaOH solution in the first stage and 0.5 M H2C2O4 in the second stage enabled the recovery of almost all the chromium initially bound to CLB (desorption efficiency = 95.9-96.1%) within long (168 h) and short (3 h) desorption periods at each stage. This study clearly demonstrated that the oxidation state of the recovered chromium depends on the chemical nature and concentration of the eluent solution. The results suggest the possible regeneration of chromium-loaded CLB for its subsequent use in other biosorption/desorption cycles.

Crosslinked modified chitosan biopolymer for enhanced removal of toxic Cr(VI) from aqueous solution

Two new crosslinked modified chitosan biopolymers, namely (CTS-VAN) and (Fe₃O₄@CTS-VAN) bioadsorbents were prepared starting from chitosan and 4-hydroxy-3-methoxybenzaldehyde (VAN) in presence of epichlorohydrin. The analytical techniques FT-IR, EDS, XRD, SEM and XPS besides BET surface analysis were utilized for full characterization of the bioadsorbents. Batch experiments were conducted to study the effect of various influencing parameters in Cr (VI) removal such as initial pH, contact time, adsorbent amount and initial Cr (VI) concentration. The adsorption of Cr (VI) was found out to be maximum at pH = 3 for both bioadsorbents. Langmuir isotherm fit well the adsorption process with a maximum adsorption capacity of 188.68 and 98.04 mg/g for CTS-VAN and Fe₃O₄@CTS-VAN, respectively. The adsorption process followed pseudo second-order kinetics with R² values of 1 and 0.9938 for CTS-VAN and Fe₃O₄@CTS-VAN, respectively. X-ray photoelectron spectroscopy (XPS) analysis showed that Cr(III) accounted for 83 % of the total Cr bound to bioadsorbents surface, which indicated reductive adsorption was responsible for Cr(VI) removal by the bioadsorbents. Cr(VI) was initially adsorbed on the positively charged surface of the bioadsorbents and reduced to Cr(III) by electrons provided by oxygen-comprising functional groups (e.g., CO), and consequently part of the converted Cr(III) stayed on the surface and the rest released into solution.

Effect of Interaction between Chromium(VI) with 17β-Estradiol and Its Metabolites on Breast Cancer Cell Lines MCF-7/WT and MDA-MB-175-VII: Preliminary Study

The number of factors initiating and stimulating the progression of breast cancer are constantly increasing. Estrogens are a risk factor for breast adenocarcinoma, the toxicity of which increases as a result of metabolism and interaction with other factors. Due to the presence of environmental exposure to estrogens and metalloestrogens, we investigated how interactions between estrogens and toxic chromium(VI)[Cr(VI)] affect breast cancer lines and investigated whether estrogens play a protective role. The aim of the study was to investigate the effect of 17β-estradiol and its metabolites: 2-methoxyestradiol (2-MeOE2), 4-hydroxyestradiol (4-OHE2), and 16α-hydroxyestrone (16α-OHE1) in exposure to Cr(VI) on cell viability and DNA cell damage. Two estrogen-dependent breast cancer cell lines, MCF 7/WT and MDA-MB-175-VII, were examined. In addition, the expression of Cu-Zn superoxide dismutase (SOD1) was determined immunocytochemically to elucidate the mechanism of oxidative stress. The effects of single substances and their mixtures were tested in the model of simultaneous and 7-day estrogen pre-incubation. As a result, the viability of MCF-7 and MDA-MB-175-VII cells is lowered most by Cr(VI) and least by 17β-E2. In the combined action of estrogens and metalloestrogens, we observed a protective effect mainly of 17β-E2 against Cr(VI)-induced cytotoxicity. The highest expression of SOD1 was found in MCF-7/WT cells exposed to 17β-E2. Moreover, high apoptosis was caused by both Cr(VI) itself and its interaction with 4-OHE2 and 2-MeOE2. The direction and dynamics of changes in viability are consistent for both lines.

Pb(II) Ion Removal Potential in Chemically Modified Ziziphus joazeiro Barks

In this study, five types of modified Ziziphus joazeiro barks were investigated for the removal of Pb(II) ions from aqueous solutions. The samples tested were natural barks, natural powder, washed with water, ethanol at 80% (EE) and 0.5 N NaOH. Batch kinetics experiments were performed under the conditions: 24−25 °C, pH 5.5−5.8, 102 mg·L−1 Pb(NO3)2, 100 rpm and 0.1 g of adsorbent, and analyses of pHpzc and Fourier transform infrared spectroscopy. All adsorbents tested showed potential to remove Pb(II) ions, but the adsorbent washed by 0.5 N NaOH obtained the highest experimental performance (25.5 mg·g−1 at 30 min), while the EE had the least performance (20.4 mg·g−1 at 60 min), and maximum removals of 99.9%. The kinetic models pointed to a probable chemisorption due to the best fit of pseudo-second order and Elovich, and Boyd’s model, suggesting that intraparticle diffusion limits the adsorption until the initial minutes of contact. The Langmuir isotherm fitted better to the experimental data for the NaOH adsorbent, with maximum adsorption capacity equal to 62.5 mg·g−1, although the Temkin model partially fitted, both suggesting the occurrence of chemisorption. The adsorption process is reversible (>81% at 20 min) and hence the adsorbents can be recycled and the Pb(II) ions recovered.

Adsorption of Cr6+ ion using activated Pisum sativum peels-triethylenetetramine

The adsorption of Cr6+ ions from water-soluble solution onto activated pea peels (PPs) embellished with triethylenetetramine (TETA) was studied. The synthesized activated TETA-PP biosorbent was further characterized by SEM together with EDX, FTIR and BET to determine the morphology and elementary composition, functional groups (FGs) present and the biosorbent surface area. The confiscation of Cr6+ ions to activated TETA-PP biosorbent was observed to be pH-reliant, with optimum removal noticed at pH 1.6 (99%). Cr6+ ion adsorption to activated TETA-PP biosorbent was well defined using the Langmuir (LNR) and the pseudo-second-order (PSO) models, with a determined biosorption capacity of 312.50 mg/g. Also, it was found that the activated TETA-PP biosorbent can be restored up to six regeneration cycles for the sequestration of Cr6+ ions in this study. In comparison with other biosorbents, it was found that this biosorbent was a cost-effective and resourceful agro-waste for the Cr6+ ion confiscation. The possible mechanism of Cr6+ to the biosorbent was by electrostatic attraction following the surface protonation of the activated TETA-PP biosorbent sites.

Iron-sulphur transformation control for enhancing Cr(VI) removal in flake and nanoscale porous pyrrhotite (Fe7S8) added wastewater

Hexavalent chromium (Cr(VI)) contaminated wastewater should be addressed efficiently in the environmental field. In previous applications, nano iron sulfides amendment has not been well controlled for iron-sulfur transformation. In this study, the novel flake and nanoscale porous pyrrhotite (Fe₇S₈) (FNPP) amendment was synthesized. The iron-sulphur transformation of FNPP was controlled and optimized for enhancing Cr(VI) removal. The specific surface area and average pore diameter of the FNPP amendment reached 115.7 m²/g and 2.1 nm. The maximum adsorption capacity of total chromium reached 66.3 mg/g. The optimized iron-sulphur transformation condition was an initial FNPP and Cr(VI) molar ratio of 8, pH at 5.6, in which the Cr(VI) removal reached 96.5% and all producing S^2- was utterly consumed. It is confirmed that S^2- fast induced Fe³⁺/Fe²⁺ circulation and FNPP has a speedier adsorption rate for Cr(III) than Cr(VI). Fe²⁺ and S^2- mediated the Cr(VI) reduction to Cr(III), thus, much faster Cr(VI) removal was achieved. High efficiency removal mechanism of Cr(VI) was combined with surface adsorption/reduction and solution reduction/precipitation. The research demonstrated that controlling and optimizing the iron-sulphur transformation of Fe₇S₈ amendment can significantly enhance Cr(VI) removal.

Resource utilization of hazardous Cr/Fe-rich sludge: synthesis of erdite flocculant to treat real electroplating wastewater

Cr/Fe-bearing sludge is a hazardous solid waste, produced at mass production in smelting, plating and surface finishing industries. Such waste is commonly treated by chemical detoxification and safety landfill, whereas only a few Cr-rich sludge is recycled as a tanning reagent. In this study, a novel route was developed to recycle Cr/Fe-bearing sludge as erdite-bearing flocculant for wastewater treatment. Results showed that two sludges were irregular aggregates, one of which contained 1.6 wt.% Cr (short for LS) and the other contained 4.2 wt.% Cr (HS). After hydrothermal treatment, stable Cr(III)/S-bearing product was formed from the Cr(VI) reduction in the sludges. Conversely, erdite was generated in nanorod form with diameter and length of 200 nm and 0.5-1 μm from LS, respectively, whereas grew radially to 1.5-2.5 μm for HS. The two erdite-bearing products were spontaneously hydrolysed to Fe/S-bearing flocs and showed similar performance in the treatment of real electroplating effluent with 91.55, 1.94 and 0.25 mg/L of Zn, Ni and Cr, respectively. For instance, by adding 1 g/L product of LS, the release of Cr from the products did not occur, and the residual Zn, Ni and Cr in the effluent was 0.25, 0.65 and 0.17 mg/L, respectively, which met the discharge standard of the electroplating industry. With the two converted products, the residual Zn/Ni/Cr concentrations were apparently lower than those of the raw sludges and other common reagents (e.g. polymeric ferric sulphate, activated carbon and diatomite). Thus, such erdite-bearing products could serve as a flocculant and then be applied in electroplating wastewater treatment.

Integrated approaches to mitigate threats from emerging potentially toxic elements: A way forward for sustainable environmental management

Potentially toxic elements (PTEs) such as toxic metal (loid)s and other emerging hazardous contaminants, exist in the environment and poses a serious threat. A large amount of wastewater containing PTEs such as cadmium, chromium, copper, nickel, arsenic, lead, zinc, etc. Release from industries during production process. Besides these, chemical-based fertilizers used in soils during crop production have become one of the crucial sources of PTEs. Various techniques are being employed for the mitigation of PTEs like chemical precipitation, ion exchange, coagulation, activated carbon, adsorption, membrane filtration, and bioremediation. Among these mitigation strategies, biological processes such as bioremediation, phytoremediation etc. Are extensively used, as they are economic have high-efficiency rate and are eco-friendly. This review intends to provide information on PTEs contamination through various sources; along with the toxicity of metal (loid)s with respect to their patterns of transmission and risks in the changing environment. Various remediation methods for the management of these pollutants along with their techno-economic perspective are also summarized in this review.

Pitahaya Fruit (Hylocereus spp.) Peels Evaluation for Removal of Pb(II), Cd(II), Co(II), and Ni(II) from the Waters

The present study investigated the performance of Pitahaya (Hylocereus spp.) peel (PP) as a low-cost biosorbent in the removal of Co(II), Cd(II), Pb(II), and Ni(II) from single and multi-component solutions. The characterization of the samples was carried out by pHpzc, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS). Biosorption was carried out by batch experimental procedure to examine the effects of contact time, solution pH, initial concentration of metal ions, and biosorbent dosage. The results indicate that the biosorption of Pb(II), Cd(II), Co(II), and Ni(II) Pitahaya peels followed pseudo-second-order kinetics, and equilibrium adsorption followed the Langmuir model. The maximum sorption capacities of PP for the metallic species were found to be as follows: Pb (82.64 mg g−1) > Cd (17.95 mg g−1) > Co (6.013 mg g−1) > Ni (5.322 mg g−1). However, the efficiency of the biosorption change when the metallic species are mixed. The re-generation of the PP after the adsorption of the metallic species was done using 0.1 M HNO3 solution, and the reusability of the biomass was carried out using two adsorption and desorption cycles.

Preparation and characterization of nano-galvanic bimetallic Fe/Sn nanoparticles deposited on talc and its enhanced performance in Cr(VI) removal

In this study, talc-supported nano-galvanic Sn doped nZVI (Talc-nZVI/Sn) bimetallic particles were successfully synthesized and utilized for Cr(VI) remediation. Talc-nZVI/Sn nanoparticles were characterized by FESEM, EDS, FTIR, XRD, zeta potential, and BET analysis. The findings verified the uniform dispersion of nZVI/Sn spherical nanoparticles on talc surface with a size of 30-200 nm, and highest specific surface area of 146.38 m2/g. The formation of numerous nano-galvanic cells between nZVI core and Sn shell enhanced the potential of bimetallic particles in Cr(VI) mitigation. Moreover, batch experiments were carried out to investigate optimum conditions for Cr(VI) elimination and total Cr(VI) removal was achieved in 20 min using Sn/Fe mass ratio of 6/1, the adsorbent dosage of 2 g/L, initial Cr(VI) concentration of 80 mg/L, at the acidic environment (pH = 5) and temperature of 303 K. Besides, co-existing of metallic cations turned out to facilitate the electron transfer from the nano-galvanic couple of NZVI/Sn, and suggested the revolution of bimetallic particles to trimetallic composites. The aging study of the nanocomposite confirmed its constant high activity during 60 days. The removal reaction was well described by the pseudo-second-order kinetic and the modified Langmuir isotherm models. Overall, due to the synergistic galvanic cell effect of nZVI/Sn nanoparticles and full coverage of active sites by Sn layer, Talc-nZVI/6Sn was utilized as a promising nanocomposite for fast and highly efficient Cr(VI) elimination.