Air sampling and analysis of polycyclic aromatic hydrocarbons

Indoor exposure to polycyclic aromatic hydrocarbons associated with solid fuel use in rural China

Polycyclic aromatic hydrocarbons (PAHs) are widespread environmental contaminants associated with various health risks including lung cancer. Indoor exposure to PAHs, particularly from the indoor burning of fuels, is significant; however, long-term large-scale assessments of indoor PAHs are hampered by high costs and time-consuming in field sampling and laboratory experiments. A simple fuel-based approach and statistical regression models were developed as a trial to predict indoor BaP, as a typical PAH, in China, and consequently spatiotemporal variations in indoor BaP and indoor exposure contributions were discussed. The results show that the national population-weighted indoor BaP concentration has decreased substantially from 46.1 ng/m3 in 1992 to 6.60 ng/m3 in 2017, primarily due to the increased use of clean energies for cooking and heating. Indoor BaP exposure contributed to > 70% of the total inhalation exposure in most cities, particularly in regions where solid fuels are widely utilized. With limited experimental observation data in building statistical models, quantitative results of the study are associated with high uncertainties; however, the study undoubtedly supports effective countermeasures on indoor PAHs from solid fuel use and the importance of promoting clean household energy usage to improve household air quality.

PAHs pollution in the outdoor air of areas with various land uses in the industrial city of Iran: distribution, source apportionment, and risk assessment

Shahryar city regions with various land uses had their outdoor air concentrations of PM_2.5-bound PAHs determined. Totally, 32 samples were taken - eight samples from the industrial region air (IS), eight samples from the high-traffic urban regions air (HTS), eight samples from the air of commercial regions (CS), and eight samples from residential areas (RS), which were analyzed by GC-MS. According to the study's findings, in the outdoor air of IS, HTS, CS, and RS, there were mean ƩPAHs concentrations of 23.25 ± 20.22, 38.88 ± 26.53, 6.97 ± 4.26, and 4.48 ± 3.13 ng/m³, respectively. As comparison to CS and RS, mean concentration of ƩPAHs in samples from HTS and IS was substantially greater (p < 0.05). Using the Unmix.6 receptor model, sources of PAHs in the air of Shahryar were allocated. The model's results show that 42% of PAHs come from diesel vehicles and industrial activities, 36% from traffic and other transportation sources, and 22% from heating sources and coal burning. The carcinogenicity suffering resulting from exposure to PAHs was as follows: This value for children of the ingestion, inhalation pathways and dermal contact is (1.90 × 10^-6-1.38 × 10^-4), (5.5 × 10^-11-2.67 × 10^-9) and (2.36 × 10^-6-1.72 × 10^-4), respectively. Also, for adults were (1.47 × 10^-6 - 1.07 × 10^-4), (1.14 × 10^-10 - 5.27 × 10^-9) and (3.68 × 10^-6- 2.87 × 10^-4), respectively. In general, the analyzed region's carcinogenicity risk estimates fell within the range of acceptable limit.

Investigation of the origin and concentration of polycyclic aromatic hydrocarbon with improved accuracy by the use of a multi-component integrated calibration method in the Katowice region, Poland

The basic variant of the integrated calibration method (ICM), based on a combination of external calibration (EC) and standard addition method (SAM), was applied to multi-component (MC) analysis to obtain a new methodological approach to improve the quality of analytical results. The analytical performance of the proposed method was evaluated on indicated by EPA polycyclic aromatic hydrocarbons (PAHs) determination in various environmental samples (air, house dust, tap water, river water, river sediment, and snow) from the Katowice region (Poland). HPLC-FLD was used during all analyses. The main aim was to show the origin of PAHs in different places in the urban and industrialized region of Poland. MC-ICM allowed for the elimination of interference from the coelution of other substances. Several diagnostic coefficients were calculated for the results free from systematic errors and interferences. The obtained results were consistent with the chemometric analysis (PCA). The method was assessed regarding analytical usefulness using the RGB model (the color method is White) and environmental friendliness using the AGREE approach.

Detection of polycyclic aromatic hydrocarbons using a high performance-single particle aerosol mass spectrometer

The real-time detection of the mixing states of polycyclic aromatic hydrocarbons (PAHs) and nitro-PAHs in ambient particles is of great significance for analyzing the source, aging process, and health effects of PAHs and nitro-PAHs; yet there is still few effective technology to achieve this type of detection. In this study, 11 types of PAH and nitro-PAH standard samples were analyzed using a high performance-single particle aerosol mass spectrometer (HP-SPAMS) in lab studies. The identification principles 'parent ions' and 'mass-to-charge (m/z) = 77' of each compound were obtained in this study. It was found that different laser energies did not affect the identification of the parent ions. The comparative experiments of ambient atmospheric particles, cooking and biomass burning emitted particles with and without the addition of PAHs were conducted and ruled out the interferences from primary and secondary organics on the identification of PAHs. Besides, the reliability of the characteristic ions extraction method was evaluated through the comparative study of similarity algorithm and deep learning algorithm. In addition, the real PAH-containing particles from vehicle exhaust emissions and ambient particles were also analyzed. This study improves the ability of single particle mass spectrometry technology to detect PAHs and nitro-PAHs, and HP-SPAMS was superior to SPAMS for detecting single particles containing PAHs and nitro-PAHs. This study provides support for subsequent ambient observations to identify the characteristic spectrum of single particles containing PAHs and nitro-PAHs.

Mobility and environmental monitoring of pesticides in the atmosphere - a review

Knowledge of the partition mechanisms in the agrochemical environment is fundamental for understanding their behavior within an ecosystem and mitigating possible adverse effects of these products. In this review, the objective was to present the main transport mechanisms, physical-chemical properties, and atmospheric monitoring methodologies of the most diverse types of agrochemicals used in agriculture that can reach the atmosphere and affect different compartments. It has been verified that volatilization is one of more considerable significance of the various forms of transport since a significant part of the applied pesticides can volatilize in a few days. As for monitoring these compounds in the atmosphere, both passive and active sampling have their advantages and disadvantages. Passive samplers allow sampling in large quantities and at remote locations, in addition to making continuous measurements, while active samplers have the advantage of being able to detect low concentrations and continuously. Since a significant portion of the applied pesticides is directed to the atmosphere, monitoring makes it possible to understand some properties of the pesticides present in the air. This monitoring can be done from different existing methodologies based on adopted criteria and existing technical standards. Graphical representation of mobility and environmental monitoring of atmospheric pollutants from pesticides.

Ambient Levels, Emission Sources and Health Effect of PM2.5-Bound Carbonaceous Particles and Polycyclic Aromatic Hydrocarbons in the City of Kuala Lumpur, Malaysia

With increasing interest in understanding the contribution of secondary organic aerosol (SOA) to particulate air pollution in urban areas, an exploratory study was carried out to determine levels of carbonaceous aerosols and polycyclic aromatic hydrocarbons (PAHs) in the city of Kuala Lumpur, Malaysia. PM2.5 samples were collected using a high-volume sampler for 24 h in several areas in Kuala Lumpur during the north-easterly monsoon from January to March 2019. Samples were analyzed for water-soluble organic carbon (WSOC), organic carbon (OC), and elemental carbon (EC). Secondary organic carbon (SOC) in PM2.5 was estimated. Particle-bound PAHs were analyzed using gas chromatography-flame ionization detector (GC-FID). Average concentrations of WSOC, OC, and EC were 2.73 ± 2.17 (range of 0.63–9.12) µg/m3, 6.88 ± 4.94 (3.12–24.1) µg/m3, and 3.68 ± 1.58 (1.33–6.82) µg/m3, respectively, with estimated average SOC of 2.33 µg/m3, contributing 34% to total OC. The dominance of char-EC over soot-EC suggests that PM2.5 is influenced by biomass and coal combustion sources. The average of total PAHs was 1.74 ± 2.68 ng/m3. Source identification methods revealed natural gas and biomass burning, and urban traffic combustion as dominant sources of PAHs in Kuala Lumpur. A deterministic health risk assessment of PAHs was conducted for several age groups, including infant, toddler, children, adolescent, and adult. Carcinogenic and non-carcinogenic risk of PAH species were well below the acceptable levels recommended by the USEPA. Backward trajectory analysis revealed north-east air mass brought pollutants to the studied areas, suggesting the north-easterly monsoon as a major contributor to increased air pollution in Kuala Lumpur. Further work is needed using long-term monitoring data to understand the origin of PAHs contributing to SOA formation and to apply source-risk apportionment to better elucidate the potential risk factors posed by the various sources in urban areas in Kuala Lumpur.

Chemometric analysis of air pollutants in raw and thermally treated coals - Low-emission fuel for domestic applications, with a reduced negative impact on air quality

The emission of pollutants into the air during the combustion of solid fuels in households is still a significant problem in many European Union countries, including Poland. These emissions are a significant source of many air pollutants formed during incomplete combustion and has been identified as one of the leading environmental risk factors for these populations. One of the solutions is to utilise thermally processed solid fuels. This article discusses the concentrations of pollutants emitted as a result of the combustion of conventional fuels and new low-emission fuel in out-of-class heaters. To gain better insight into the relationships between fuel type and flue gas quality, chemometric methods and variance analysis were used. Principal component analysis confirmed that the fuel type significantly influences the level of dust emissions and the total organic carbon and sum of polycyclic aromatic hydrocarbons in the dust. Clustering analysis identified how the concentrations of polycyclic aromatic hydrocarbons correlate with the amounts of dust and total organic carbon and showed that this correlation is proportional to the size of the molecule and consequently the number of aromatic rings. The use of low-emission fuel as a solid fuel in households, as our analyses have shown, can reduce the concentrations of dust, total organic carbon and polycyclic aromatic hydrocarbons by up to 50 times, thereby reducing air pollutants in cities.

Evaluation of silicone-based wristbands as passive sampling systems using PAHs as an exposure proxy for carcinogen monitoring in firefighters: Evidence from the firefighter cancer initiative

Compared to the general population, firefighters are known to sustain greater levels of exposure to hazardous compounds, despite their personal protective equipment, also known as turnout gear. Among the most significant toxins that firefighters are chronically exposed to are polycyclic aromatic hydrocarbons (PAHs). Additionally, firefighters have also been noted to exhibit an increased incidence of certain types of cancer. Considering a probable link between exposure to PAHs and increased rates of cancer in the fire service, we aim to document ambient chemical concentrations in the firefighter work environment. Our strategy involves the use of silicone-based wristbands that have the capacity to passively sorb PAHs. To determine if wristbands can serve as an effective chemical monitoring device for the fire service, silicone wristbands were pilot-tested as personal sampling devices for work environment risk monitoring in active-duty firefighters. Recovered wristbands underwent multiple extraction steps, followed by GC-MS analysis to demonstrate their efficacy in monitoring PAHs in the firefighter environment. Initial findings from all wristband samples taken from firefighters showed multiple exposures to various PAHs of concern for the health of the firefighters when in a fire environment. In addition to PAH monitoring, we examined known and potential sources of PAH contamination in their work environment. To that end, profiles of elevated PAH concentrations were documented at various fire stations throughout South Florida, for individual firefighters both during station duties and active fire response.

Nano-hydroxyapatite/polyaniline composite as an efficient sorbent for sensitive determination of the polycyclic aromatic hydrocarbons in air by a needle trap device

Hydroxyapatite is a readily available, inexpensive, environmentally friendly adsorbent with high adsorption capacity. In this study, a polyaniline-doped nano-hydroxyapatite (PANI@HA) adsorbent was synthesized and employed in a needle trap device for the extraction of polycyclic aromatic hydrocarbons such as naphthalene, fluoranthene, benzo[a]anthracene, phenanthrene, and benzo[a]pyrene for the first time. The synthesized adsorbent was characterized by X-ray diffraction, field emission scanning electron microscopy, and Fourier-transform infrared spectroscopy analysis. Initially, effective variables such as the carryover effect, storage time, accuracy, and precision of the method were examined in the laboratory. The desorption conditions were optimized using the response surface methodology and central composite design methods. From the standpoint of quantitative parameters, the limit of detection and limit of quantitation were determined to be between 0.001 and 0.003 and 0.021 and 0.051 ng mL-1, respectively, which indicates the high sensitivity of the proposed method. Additionally, no significant changes were detected after storage of analytes inside the needle at 4 °C after 60 days. The results of this study also provide a high correlation between the results of sampling with needles containing PANI@HA and with XAD-2 adsorbent tubes (standard NIOSH 5115 method) (R 2 = 0.98). Finally, the proposed method was successfully employed in the extraction and determination of polycyclic aromatic hydrocarbons in field (real) samples. In general, it can be concluded that a needle packed with PANI@HA is a reliable and high-performance method for sampling polycyclic aromatic hydrocarbons compared to the NIOSH method.

Polycyclic aromatic compounds (PACs) in the Canadian environment: A review of sampling techniques, strategies and instrumentation

A wide variety of sampling techniques and strategies are needed to analyze polycyclic aromatic compounds (PACs) and interpret their distributions in various environmental media (i.e., air, water, snow, soils, sediments, peat and biological material). In this review, we provide a summary of commonly employed sampling methods and strategies, as well as a discussion of routine and innovative approaches used to quantify and characterize PACs in frequently targeted environmental samples, with specific examples and applications in Canadian investigations. The pros and cons of different analytical techniques, including gas chromatography - flame ionization detection (GC-FID), GC low-resolution mass spectrometry (GC-LRMS), high performance liquid chromatography (HPLC) with ultraviolet, fluorescence or MS detection, GC high-resolution MS (GC-HRMS) and compound-specific stable (δ¹³C, δ²H) and radiocarbon (Δ¹⁴C) isotope analysis are considered. Using as an example research carried out in Canada's Athabasca oil sands region (AOSR), where alkylated polycyclic aromatic hydrocarbons and sulfur-containing dibenzothiophenes are frequently targeted, the need to move beyond the standard list of sixteen EPA priority PAHs and for adoption of an AOSR bitumen PAC reference standard are highlighted.

An overview of research and development themes in the measurement and occurrences of polyaromatic hydrocarbons in dusts and particulates

Polycyclic aromatic hydrocarbons (PAHs) are a group of organic compounds consisting of two or more fused aromatic rings and are probably one of the most studied groups of organic chemicals in environmental research. PAHs originate mainly from anthropogenic processes, particularly from incomplete combustion of organic fuels. PAHs are distributed widely in particulate matter. Due to widespread sources and persistent characteristics, PAHs disperse through atmospheric transport and exist almost everywhere. Human beings are exposed to PAH mixtures in gaseous or particulate phases in ambient air. Long-term exposure to high concentrations of PAHs is associated with adverse health problems. This review identifies the main research and development themes in the measurement and occurrences of PAHs in dusts and particulates using a new approach to carrying out a literature review where many peer-review publications have been produced. The review extracts the most important research themes from a literature search using a combination of text mining and a more detailed review of selected papers from within the identified themes.

Ionization of Gas-Phase Polycyclic Aromatic Hydrocarbons in Electrospray Ionization Coupled with Gas Chromatography

Herein, gas-phase polycyclic aromatic hydrocarbons (PAHs) as nonpolar compounds were ionized to protonated molecular ions [M + H]⁺ without radical cations and simultaneously analyzed using gas chromatography (GC)/electrospray ionization (ESI)-tandem mass spectrometry (MS/MS). The ionization profile, dissociation, and sensitivity were first investigated to understand the significant behavior of gas-phase PAHs under ESI. The formation of protonated molecular ions of PAHs was distinguished according to the analyte phase and ESI spray solvents. The protonated PAHs exhibited characteristic dissociations, such as H-loss, H₂-loss, and acetylene-loss, via competition of internal energy. In addition, GC/ESI-MS/MS resulted in relatively lower concentration levels (better sensitivity) for the limits-of-detection (LODs) of PAHs than liquid chromatography (LC)/ESI-MS/MS, and it seems to result from the characteristic ionization mechanism of the gas-phase analyte under ESI. Furthermore, the LODs of gas-phase PAHs depended on molecular weight and proton affinity (PA). Consequently, we demonstrated the relationship among the analyte phases, sensitivities, and structural characteristics (molecular weight and PA) under ESI. The gas-phase PAHs provided enhanced protonation efficiency and sensitivity using GC/ESI-MS/MS, as their molecular weight and PA increased. Based on these results, we offered important information regarding the behavior of gas-phase analytes under ESI. Therefore, the present GC/ESI-MS/MS method has potential as an alternative method for simultaneous analysis of PAHs.

Influence of transport from urban sources and domestic biomass combustion on the air quality of a mountain area

The environmental influence of biomass burning for civil uses was investigated through the determination of several air toxicants in the town of Leonessa and its surroundings, in the mountain region of central Italy. Attention was focussed on PM₁₀, polycyclic aromatic hydrocarbons (PAHs) and regulated gaseous pollutants (nitrogen dioxide, ozone and benzene). Two in-field campaigns were carried out during the summer 2012 and the winter 2013. Contemporarily, air quality was monitored in Rome and other localities of Lazio region. In the summer, all pollutants, with the exception of ozone, were more abundant in Rome. On the other hand, in the winter, PAH concentration was higher in Leonessa (15.8 vs. 7.0 ng/m³), while PM₁₀ was less concentrated (22 vs. 34 μg/m³). Due to lack of other important sources and to limited impact of vehicle traffic, biomass burning was identified as the major PAH source in Leonessa during the winter. This hypothesis was confirmed by PAH molecular signature of PM₁₀ (i.e. concentration diagnostic ratios and 206 ion mass trace in the chromatograms). A similar phenomenon (i.e. airborne particulate levels similar to those of the capital city but higher PAH loads) was observed in other locations of the province, suggesting that uncontrolled biomass burning contributed to pollution across the Rome metropolitan area.

FTIR analysis and evaluation of carcinogenic and mutagenic risks of nitro-polycyclic aromatic hydrocarbons in PM1.0

Nitro-polycyclic aromatic hydrocarbons (NPAHs) represent a group of organic compounds of significant interest due to their presence in airborne particulates of urban centers, wide distribution in the environment, and mutagenic and carcinogenic properties. These compounds, associated with atmospheric particles of size < 1 μm, have been reported as a major risk to human health. This study aims at identifying the spectral features of NPAHs (1-nitropyrene, 2-nitrofluorene, and 6-nitrochrysene) in emissivity and transmittance spectra of samples of particulate matter < 1 μm (PM1.0) using infrared spectrometry. Carcinogenic and mutagenic risks of the studied NPAHs associated with PM1.0 samples were also determined for two sampling sites: Canoas and Sapucaia do Sul. The results showed that NPAH standard spectra can effectively identify NPAHs in PM1.0 samples. The transmittance and emissivity sample spectra showed broader bands and lower relative intensity than the standard NPAH spectra. The carcinogenic risk and the total mutagenic risk were calculated using the toxic equivalent factors and mutagenic potency factors, respectively. Canoas showed the highest total carcinogenic risk, while Sapucaia do Sul had the highest mutagenic risk. The seasonal analysis suggested that in the study area the ambient air is more toxic during the cold periods. These findings might of significant importance for the decision and policy making authorities.

Analytical method for determining polycyclic aromatic hydrocarbon pollutants using ultrafast liquid chromatography with fluorescence detection and the recent column packed with the new 5 μm Kinetex-C18 core-shell particles

An ultrafast liquid chromatography method with fluorescence detection has been optimized for the determination of 15 polycyclic aromatic hydrocarbons (PAHs) using a recent Kinetex-C18 column (250 mm × 4.6 mm). This column has been recently packed with a new brand of porous shell particles with an average particle size of 5 μm to separate various compounds by liquid chromatography, operating at very low pressure. After optimization of the analytical procedure, the separation of the 15 PAHs in spiked tap water samples was achieved without coeluted products in 21.5 min at 16 °C using an aqueous/acetonitrile mobile phase under gradient concentrations with a very low flow rate (0.7–1.0 mL min−1) and low pressure values (870–1590 psi = 60–110 bar), all of these conditions being interesting from an economic point of view. The synchronization of wavelength time changing and the elution time of each compound was performed to avoid baseline deviation. The validation of the whole of the experimental procedure was conducted taking into consideration the following parameters: calibration curve, linearity, limits of detection and quantification, accuracy, sensitivity, precision, and repeatability of the retention time for each PAH. The proposed analytical procedure presented adequate linearity over a concentration range from 0.025 to 10 μg L−1 with a correlation coefficient better than 0.9980. The repeatability (relative standard deviation in percentage, n = 5) of the retention time for the different PAHs investigated ranged from 0.03% to 0.34% and the limit of detection was under 0.6 μg L−1 for most PAHs (excepted for indeno[1,2,3-c,d]pyrene, limit of detection = 1.71 μg L−1). The intraday and interday precisions were below 4%. The recovery of PAH in spiked tap water samples was variable, ranging from 96% to 109%, with relative standard deviation between 0.2% and 4.8%, depending on PAHs and their concentration levels.

A seasonal study of polycyclic aromatic hydrocarbons in PM(2.5) and PM(2.5-10) in five typical cities of Liaoning Province, China

Fourteen polycyclic aromatic hydrocarbons (PAHs) in PM(2.5) and PM(2.5-10) samples collected in five cities (Shenyang, Anshan, Jinzhou, Fushun and Dalian), Liaoning Province, China in 2004 and 2005 were analyzed by using a HPLC equipped with fluorescence and UV detectors. Results showed total PAHs concentrations in PM(2.5) and PM(2.5-10) were in the range of 75.32-1900.89 ng m(-3) and 16.74-303.24 ng m(-3), respectively. 90% of the total PAHs were in PM(2.5). PAHs in PM(2.5) had a winter to summer ratio varying from 6.5 to 125.8 while PAHs in PM(2.5-10) had a ratio ranging from 1.7 to 37.6. Total PAHs concentrations were most abundant at residential/commercial sites and were fewest at an industrial site for both PM(2.5) and PM(2.5-10). Urban background sites showed unexpected higher PAHs concentrations. Total BaP equivalent concentration (BaPeq) for PM(2.5) ranged from 7.80 to 88.42 ng m(-3) in different function zones. Similarities of PAHs profiles between sampling sites and between fine and coarse fractions were compared by coefficient of divergence which indicated that remarkable differences in PAHs compositions existed. Principal component analysis (PCA) associated with diagnostic ratios revealed coal combustion and vehicle emission were the major sources for PM(2.5) and PM(2.5-10) associated PAHs.

Polycyclic aromatic hydrocarbons (PAHs) in atmospheric urban area: monitoring on various types of sites

The air quality over the Toulouse urban area (France) is recorded daily by the regional "Midi-Pyrénées" atmospheric pollution measurements network (ORAMIP). Relevant data is collected from about 100 analysers spread over more than thirty stations. The regulations covering major indicators of atmospheric pollution (ozone, nitrogen dioxide, sulphur dioxide) have been updated in recent years to include additional compounds like polycyclic aromatic hydrocarbons (PAHs). The ORAMIP, in partnership with the ENSIACET has undertaken background PAH average concentration measurements over the urban agglomeration of Toulouse during spring 2006 for various types of sites (traffic, urban, industrial). The sampling was performed using a low volume air sampler equipped with quartz fiber filters and polyurethane foams For the two urban sites, total atmospheric concentrations between 12 and 20 ng/m(3) have been obtained, whereas for the industrial site the values averaged 22 ng/m(3). In addition, and regardless of site, the average concentrations of benzo[a]pyrene, at present the only regulated PAH, were always less than the 1 ng/m(3) limit.

PAH mass concentrations measured in PM10 particle fraction

This paper presents daily, monthly and yearly variations of PAH mass concentrations measured in PM(10) particle fraction, collected at one measuring site in Zagreb air between 2001 and 2004, and seasonal differences in PAH mass concentrations in PM(10) samples collected from 21 March 2003 to 20 March 2004. Twenty-four hour samples were taken in the northern residential part of Zagreb using a low-volume (50 m(3)) sampler and glass or quartz filters. The analysis was performed using a high-performance liquid chromatograph (HPLC) and fluorescence detector with changeable excitation and emission wavelength. The annual average mass concentrations over the four-year measuring period for BaP ranged from 1.17 ng/m(3) in 2004 to 1.87 ng/m(3) in 2003 and were below the limit value (2 ng/m(3)) set by the Ordinance on Recommended and Limit Air Quality Values in Croatia. The highest concentrations of all PAHs measured in PM(10) samples collected from 21 March 2003 to 20 March 2004 were found in the winter and the lowest in the summer. Winter average of BaP was 2.94 ng/m(3) and summer average 0.12 ng/m(3). Autumn average was 2.76 ng/m(3) and was very similar to winter concentrations. Spring average of 0.58 ng/m(3) was higher than the summer average (0.12 ng/m(3)). Mass concentrations of all measured PAHs were much higher in the autumn than in the spring. Although annual averages for BaP did not exceed the limit value, autumn and winter BaP mass concentrations did, which calls for measures for reducing PAH emissions in the autumn and winter.

Rapid analysis of SVOC in aerosols by desorption electrospray ionization mass spectrometry

Desorption electrospray ionization mass spectrometry (DESI-MS) was applied for the first time to the analysis of semivolatile organic compounds (SVOC) in atmospheric aerosols. We took polycyclic aromatic hydrocarbons (PAHs) as representatives of SVOCs. The DESI-MS conditions were optimized and the limit of detection for PAHs was about 10 pg with 5 s sampling time. PAHs from both laboratory-made biomass burning aerosols and ambient aerosols were selectively and rapidly analyzed without extraction or preconcentration. The observed PAH species and their relative ion intensities are discussed. This work demonstrates that DESI-MS is a promising method for rapid semiquantitative analysis of SVOC in atmospheric aerosols.

Solid-phase extraction with C30 bonded silica for analysis of polycyclic aromatic hydrocarbons in airborne particulate matters by gas chromatography–mass spectrometry

A solid-phase extraction (SPE) method using triacontyl bonded silica (C30) as sorbent was developed for the determination of 16 US Environmental Protection Agency polycyclic aromatic hydrocarbons (PAHs) in airborne particulate matters quantitatively by gas chromatography-mass spectrometry (GC-MS). Optimization experiments were conducted using spiked standard aqueous solution of PAHs and real airborne particulates samples aiming to obtain highest SPE recoveries and extraction efficiency. Factors were studied in SPE procedures including the concentration of organic modifier, flow rate of sample loading and elution solvents. The ultrasonication time and solvents were also investigated. Recoveries were in the range of 68-107% for standard PAHs aqueous solution and 61-116% for real spiked sample. Limits of detection (LODs) and limits of quantification (LOQs) with standard solution were in the range of 0.0070-0.21 microgL(-1) and 0.022-0.67 microgL(-1), respectively. The optimized method was successfully applied to the determination of 16 PAHs in real airborne particulate matters.

Development of analytical methods for polycyclic aromatic hydrocarbons (PAHs) in airborne particulates: a review

In the present work, the different sample collection, pretreatment and analytical methods for polycyclic aromatic hydrocarbons (PAHs) in airborne particulates is systematacially reviewed, and the applications of these pretreatment and analytical methods for PAHs are compared in detail. Some comments on the future expectation are also presented.

Long-Term Diffusive Samplers for the Indoor Air Quality Evaluation

Three kinds of diffusion samplers, conceived to perform long-term samplings in indoor sites are illustrated in this work. Two of them, in part deriving from the previous "Analyst for VOC" device, extend the field of application up to the semi-volatile organic compounds (SVOC), PAHs and nicotine in particular. A third device, which employs a basic barium hydroxide solution as an absorbing medium, is proposed for the determination of carbon dioxide levels which indicate the air change quality in the indoor sites. Laboratory and field experiments, performed in order to assess the reliability of the proposed devices, are shown. A monthly monitoring campaign, performed at three private apartments in Rome and its outskirts highlights that the indoor pollution levels are a complex function of various concurrent and opposite factors, like external air pollution, internal sources, air change rate and sink effect of surfaces, which contribute to depletion phenomena through adsorption and/or decomposition processes.

Screening and determination of pesticides in soil using continuous subcritical water extraction and gas chromatography-mass spectrometry

In the present work the efficiency of water under subcritical conditions for the extraction of pesticides having a broad spectrum of polarities from soils was evaluated. The pesticides under study were carbofuran, hexachlorobenzene, dimethoate, simazine, atrazine, lindane, diazinon, methylparathion, alachlor, aldrin-R, metholachlor, chlorpyrifos, heptachlor epoxide, dieldrin, endrin, 4,4-DDT and metoxichlor. Optimization studies were carried out using a blank soil (Non-Polluted Soil 1, CLN-1, RTC) and a real soil which were previously spiked with the pesticide mixture and aged for 60 days. A laboratory-made aluminum oven with controlled temperature was used to carry out the leaching process with subcritical water, where it is placed a pre-heater and the extraction cell. The following variables were studied, keeping the pressure controlled about 1200 p.s.i.: the extraction temperature, the time of static and dynamic extraction and the flow-rate of water (1 p.s.i. = 6894.76 Pa). The extraction efficiency of the pesticides increases with the temperature trending to the quantitative extraction at temperatures near to 300 degrees C. After the extraction process, the analytes were transferred quantitatively to 5 ml dichloromethane, before the determination by GC-MS. The results indicate that under the optimized conditions mostly of the analytes are extracted quantitatively in 90 min with recoveries quite similar to those obtained by the standard Soxhlet extraction procedure. Alternatively, by using an extraction time of 25 min, the method can be used as screening for all the pesticides, with recoveries depending on their polarity.

Exposure of garbage truck drivers and maintenance personnel at a waste handling centre to polycyclic aromatic hydrocarbons derived from diesel exhaust

Exposure to diesel exhaust was evaluated in summer and winter by measuring vapour and particle phase polycyclic aromatic hydrocarbons (PAHs). Fifteen PAHs were simultaneously determined from the air samples obtained from truck drivers collecting household waste and maintenance personnel at a waste handling centre. The major compounds analysed from the personal air samples of exposed workers were naphthalene, phenanthrene and fluorene. The total PAH exposure (sum of 15 PAHs) of garbage truck drivers ranged from 71 to 2,660 ng m(-3) and from 68 to 900 ng m-3 in the maintenance work. The exposure of garbage truck drivers to benzo[a]pyrene (B[a]P) ranged from the mean of 0.03 to 0.3 ng m(-3) whereas no B[a]P in control samples or in those collected from maintenance workers was detected. A statistically significant difference in diesel-derived PAH exposure between the garbage truck drivers and the control group in both seasons (in summer p = 0.0022, degrees of freedom (df) 70.5; and in winter p < 0.0001, df = 80.4) was observed. Also, a significant difference in PAH exposure between the garbage truck drivers and the maintenance workers (in summer p < 0.0001, df = 50.1; and in winter p < 0.0001, df = 44.2) was obtained.

Solid-phase extraction of sugar cane soot extract for analysis by gas chromatography with flame ionisation and mass spectrometric detection

The incomplete combustion of biomass is one of the most important sources of emissions of organic compounds into the atmosphere, like polycyclic aromatic hydrocarbons (PAHs) which show genotoxic activity. Since environmental samples generally contain interferents and trace amounts of PAHs of interest, concentration and clean-up procedures are usually required prior to the final chromatographic analysis. This paper discusses the performance of Sep-Pak cartridges (silica gel and RP18) on clean-up of sugar cane soot extract. The best results were obtained with a silica Sep-Pak cartridge. The recoveries ranged from 79% (benzo[b]fluoranthene) to 113% (benzo[e]pyrene).

Solid-phase extraction of polycyclic aromatic compounds

Solid-phase extraction (SPE) for two groups of polyaromatic compounds--polycyclic aromatic hydrocarbons and naphthalenesulfonates--with completely different problems in the extraction process are reviewed. The sorbents used in each case and the different steps of SPE are studied. Particular problems encountered in the SPE of each group are described. Adsorption problems of PAHs which require an organic solvent or a surfactant to be added to the sample are explained. The need of ion-pair solid-phase extraction for extracting naphthalenesulfonates and the influence of the inorganic species in the extraction are discussed. The on-line systems are described for both group of compounds.

Genotoxicity of fractionated organic material in airborne particles from São Paulo, Brazil

Particulate matter less than 10 microns aerodynamic diameter (PM10) is associated with adverse health effects including increased respiratory problems and mortality. PM10 is also associated with increases in cancer in some urban areas. Identification of toxic compounds in PM10 is a step toward estimating exposure to these compounds and evaluating their public health risk. However, the toxic compounds on PM10 are part of a highly complex mixture of compounds that makes chemical characterization difficult. Before this study, there has been little investigation of genotoxic compounds in particulate matter from Latin American cities. Here, both bioassay (mutagenicity) and chemical analyses were conducted with organic solvent extracts of PM10 collected from São Paulo, a major Brazilian city. Sequential extraction in dichloromethane (DCM) followed by acetone (ACE) yielded 20.3% and 10.2% of the total mass, respectively. Non-polar and moderately polar organic material solubilized in DCM. ACE extracted more polar organic species and some inorganic ions. Both extracts were fractionated separately using cyanopropyl-bonded silica chromatography with organic solvents of increasing polarity. The mass distribution among the fractions was measured. The mutagenic activity of the fractions was assayed using the microsuspension procedure with the Salmonella typhimurium tester strain TA98, with and without addition of metabolic enzymes (S9). The DCM extract had about four times higher mutagenic activity than the ACE extract. In general, addition of S9 resulted in an increase in mutagenicity of DCM fractions, but a decrease for the ACE extract. Most of the activity was concentrated in fractions in the mid-range of polarity within both the DCM and ACE extracts. The fractions were analyzed by gas chromatography with mass selective detection (GC/MS) without derivatization. The most mutagenic fractions in the DCM extract contained ketones, aldehydes, and quinolines. The most mutagenic ACE fraction had ketones, carboxylic acids, and aldehydes.