Dynamic glutaraldehyde fixation of a porcine aortic valve xenograft. I. Effect of fixation conditions on the final tissue viscoelastic properties

Mechanical testing of glutaraldehyde cross-linked mitral valves. Part two: Elastic and viscoelastic properties of chordae tendineae

The aim of this study was to assess whether the mechanical properties of mitral valve chordae tendineae are sensitive to being cross-linked under load. A total 64 chordae were extracted from eight porcine hearts. Two chordae (posterior basal) from each heart were subjected to uniaxial ramp testing and six chordae (two strut, two anterior basal and two posterior basal) were subjected to dynamic mechanical analysis over frequencies between 0.5 and 10 Hz. Chordae were either cross-linked in tension or cross-linked in the absence of loading. Chordae cross-linked under load transitioned from high to low extension at a lower strain than cross-linked unloaded chordae (0.07 cf. 0.22), with greater pre-transitional (30.8 MPa cf. 5.78 MPa) and post-transitional (139 MPa cf. 74.1 MPa) moduli. The mean storage modulus of anterior strut chordae ranged from 48 to 54 MPa for cross-linked unloaded chordae, as compared to 53-61 MPa cross-linked loaded chordae. The mean loss modulus of anterior strut chordae ranged from 2.3 to 2.9 MPa for cross-linked unloaded chordae, as compared to 3.8-4.8 MPa cross-linked loaded chordae. The elastic and viscoelastic properties of chordae following glutaraldehyde cross-linking are dependent on the inclusion/exclusion of loading during the cross-linking process; with loading increasing the magnitude of the material properties measured.

Structure and Rheological Properties of Bovine Aortic Heart Valve and Pericardium Tissue: Implications in Bioprosthetic and Tissue-Engineered Heart Valves

Heart valve (HV) diseases are among the leading causes of cardiac failure and deaths. Of the various HV diseases, damaged HV leaflets are among the primary culprits. In many cases, impaired HV restoration is not always possible, and the replacement of valves becomes necessary. Bioprosthetic HVs have been used for the replacement of the diseased valves, which is obtained from the sources of bovine and porcine origin, while tissue-engineered heart valves (TEHV) have emerged as a promising future solution. The bioprosthetic valves are prone to become calcified, and thus they last for only ten to fifteen years. The adequate understanding of the correlations between the biomechanics and rheological properties of native HV tissues can enable us to improve the durability of the bioprosthetic HV as well as help in the development of tissue-engineered heart valves (TEHV). In this study, the structural and rheological properties of native bovine aortic HV and pericardium tissues were investigated. The microstructures of the tissues were investigated using scanning electron microscopy, while the rheological properties were studied using oscillatory shear measurement and creep test. The reported results provide significant insights into the correlations between the microstructure and viscoelastic properties of the bovine aortic HV and pericardium tissues.

Biaxial stress relaxation of semilunar heart valve leaflets during simulated collagen catabolism: Effects of collagenase concentration and equibiaxial strain state

Heart valve leaflet collagen turnover and remodeling are innate to physiological homeostasis; valvular interstitial cells routinely catabolize damaged collagen and affect repair. Moreover, evidence indicates that leaflets can adapt to altered physiological (e.g. pregnancy) and pathological (e.g. hypertension) mechanical load states, tuning collagen structure and composition to changes in pressure and flow. However, while valvular interstitial cell-secreted matrix metalloproteinases are considered the primary effectors of collagen catabolism, the mechanisms by which damaged collagen fibers are selectively degraded remain unclear. Growing evidence suggests that the collagen fiber strain state plays a key role, with the strain-dependent configuration of the collagen molecules either masking or presenting proteolytic sites, thereby protecting or accelerating collagen proteolysis. In this study, the effects of equibiaxial strain state on collagen catabolism were investigated in porcine aortic valve and pulmonary valve tissues. Bacterial collagenase (0.2 and 0.5 mg/mL) was utilized to simulate endogenous matrix metalloproteinases, and biaxial stress relaxation and biochemical collagen concentration served as functional and compositional measures of collagen catabolism, respectively. At a collagenase concentration of 0.5 mg/mL, increasing the equibiaxial strain imposed during stress relaxation (0%, 37.5%, and 50%) yielded significantly lower median collagen concentrations in the aortic valve (p = 0.0231) and pulmonary valve (p = 0.0183), suggesting that relatively large strain magnitudes may enhance collagen catabolism. Collagen concentration decreases were paralleled by trends of accelerated normalized stress relaxation rate with equibiaxial strain in aortic valve tissues. Collectively, these in vitro results indicate that biaxial strain state is capable of affecting the susceptibility of valvular collagens to catabolism, providing a basis for further investigation of how such phenomena may manifest at different strain magnitudes or in vivo.

Electrospun Polyurethane and Hydrogel Composite Scaffolds as Biomechanical Mimics for Aortic Valve Tissue Engineering

In this study, a composite scaffold consisting of an electrospun polyurethane and poly(ethylene glycol) hydrogel was investigated for aortic valve tissue engineering. This multilayered approach permitted the fabrication of a scaffold that met the desired mechanical requirements while enabling the 3D culture of cells. The scaffold was tuned to mimic the tensile strength, anisotropy, and extensibility of the natural aortic valve through design of the electrospun polyurethane mesh layer. Valve interstitial cells were encapsulated inside the hydrogel portion of the scaffold around the electrospun mesh, creating a composite scaffold approximately 200 μm thick. The stiffness of the electrospun fibers caused the encapsulated cells to exhibit an activated phenotype that resulted in fibrotic remodeling of the scaffold in a heterogeneous manner. Remodeling was further explored by culturing the scaffolds in both a mechanically constrained state and in a bent state. The constrained scaffolds demonstrated strong fibrotic remodeling with cells aligning in the direction of the mechanical constraint. Bent scaffolds demonstrated that applied mechanical forces could influence cell behavior. Cells seeded on the outside curve of the bend exhibited an activated, fibrotic response, while cells seeded on the inside curve of the bend were a quiescent phenotype, demonstrating potential control over the fibrotic behavior of cells. Overall, these results indicate that this polyurethane/hydrogel scaffold mimics the structural and functional heterogeneity of native valves and warrants further investigation to be used as a model for understanding fibrotic valve disease.

Modifications on Collagen Structures Promoted by 1,4-Dioxane Improve Thermal and Biological Properties of Bovine Pericardium as a Biomaterial

Collagen is a widely used raw material for biomaterial manufacture, which generally depends on chemical modifications of this fibrillar protein with cross-linking agents to improve biocompatibility and mechanical properties. However, cross-linking reduces the natural properties of collagen, such as low immune response, low toxicity as well as the ability to promote cellular growth and attachment. In this work, the modifications promoted by 1,4-dioxane solvent on the collagen present in native bovine pericardium (NBP) matrix routinely used in bioprosthesis manufacture, with or without subsequent cross-linking by glutaraldehyde, has been studied. The structural changes of NBP evaluated by scanning electron microscopy show that 1,4-dioxane induces a more homogeneous material by increasing aggregation of collagen fibers, while transmission scanning electron microscopy shows that natural collagen fibril arrangement, integrity, and the D-periodicity pattern are maintained by solvent treatments. Measurements of thermal stability and resistance to collagenase enzymatic digestion of NBP matrices treated with 1,4-dioxane show an increase in melting temperature and decrease in biodegradability, as compared to native pericardium. Cross-linking with glutaraldehyde improves all the analyzed NBP properties, which are not impaired by previous treatment with 1,4-dioxane. Histological evaluation of NBP submitted to 1,4-dioxane treatment shows lower lipid and cell contents and improvement in other morphologic characteristics compared to native pericardium. Altogether, these results suggest the use of 1,4-dioxane organic solvent as an alternative non-cross-linking treatment for direct utilization on rich collagen matrices, resulting in materials with improved biocompatibility and physicochemical properties suitable for tissue engineering.

Activity of MMP-9 after repair of abdominal wall defects with acellular and crosslinked bovine pericardium in rabbit

This study was undertaken for the identification of matrix metalloproteinases (MMPs) in extracts obtained from native, acellular and crosslinked bovine pericardium (in vitro), as well as in the plasma after implantation of these biomaterials in rabbits (in vivo). Native pericardium (NP) expressed a 72 kDa (MMP-2) band; whereas, in acellular pericardium (AP) two bands (10 kDa and 92 kDa) of MMPs were observed of which, 92 kDa band was very faint. AP crosslinked with glutaraldehyde did not show any gelatinase activity and thus reflects the creation of new additional chemical bonds between the collagen molecules which has been effectively removed. Gelatin zymography showed only one major band of 92 kDa in all the implanted and untreated rabbit plasma, but the relative amount of 92 kDa was 1-2 times higher in acellular bovine pericardium implanted rabbits as compared to crosslinked and native groups. In NP group, the 92 kDa band was the dullest among the three groups. This indicated that the level of MMP-9 corresponds to the degree of collagen degradation.

Fabrication of a human recombinant collagen-based corneal substitute using carbodiimide chemistry

Human recombinant collagen can be cross-linked with a variety of chemical cross-linking agents. Cross-linking methods can be tuned to confer collagen-based scaffolds with specific physical properties, improved antigenicity and thermal stability without impeding the ability of the material to integrate into the surrounding tissue and to promote regeneration. Here, we describe a method to cross-link human recombinant collagen using a water soluble carbodiimide. Carbodiimides are referred to as zero-length cross-linking agents as they are not incorporated into the final cross-link and thus pose minimal risk with respect to cytotoxicity. The resulting collagen-based scaffold possesses properties comparable to that of the human cornea and is thus suitable for use as a corneal substitute.

Fixation and Mounting of Porcine Aortic Valves for use in Mock Circuits

Purpose

Investigations of the circulatory system in vitro use mock circuits that require valves to mimic the cardiac situation. Whereas mechanical valves increase water hammer effects due to inherent stiffness and do not allow the use of pressure lines or catheters, bioprosthetic valves are expensive and of limited durability in test fluids. Therefore, we developed a cheap, fast, alternative method to mount valves obtained from the slaughterhouse in mock circuits.

Methods

Porcine aortic roots were obtained from the abattoir and used either in native condition or after fixation. Fixation was performed at a constant retrograde pressure to ensure closed valve position. Fixation time was 4 h in a 0.5%-glutaraldehyde phosphate buffer. The fixed valves were molded into a modular mock circulation connector using a fast curing silicone. Valve functionality was evaluated in a pulsatile setting (cardiac output = 4.7 l/min, heart rate = 80 beats/min) and compared before and after fixation. Leaflet motion was recorded with a high-speed camera and valve insufficiency was quantified by leakage flow under steady pressure application (80 mmHg).

Results

Under physiological conditions the aortic valves showed almost equal leaflet motion in native and fixed conditions. However, the leaflets of the native valves showed lower stiffness and more fluttering during systole than the fixed specimens. Under retrograde pressure, fresh and fixed valves showed small leakage flows of <30 ml/min.

Conclusions

The new mounting and fixation procedure is a fast method to fabricate low cost biologic valves for the use in mock circuits.

Structural mechanism for alteration of collagen gel mechanics by glutaraldehyde crosslinking

Soft collagenous tissues that are loaded in vivo undergo crosslinking during aging and wound healing. Bioprosthetic tissues implanted in vivo are also commonly crosslinked with glutaraldehyde (GA). While crosslinking changes the mechanical properties of the tissue, the nature of the mechanical changes and the underlying microstructural mechanism are poorly understood. In this study, a combined mechanical, biochemical and simulation approach was employed to identify the microstructural mechanism by which crosslinking alters mechanical properties. The model collagenous tissue used was an anisotropic cell-compacted collagen gel, and the model crosslinking agent was monomeric GA. The collagen gels were incrementally crosslinked by either increasing the GA concentration or increasing the crosslinking time. In biaxial loading experiments, increased crosslinking produced (1) decreased strain response to a small equibiaxial preload, with little change in response to subsequent loading and (2) decreased coupling between the fiber and cross-fiber direction. The mechanical trend was found to be better described by the lysine consumption data than by the shrinkage temperature. The biaxial loading of incrementally crosslinked collagen gels was simulated computationally with a previously published network model. Crosslinking was represented by increased fibril stiffness or by increased resistance to fibril rotation. Only the latter produced mechanical trends similar to that observed experimentally. Representing crosslinking as increased fibril stiffness did not reproduce the decreased coupling between the fiber and cross-fiber directions. The study concludes that the mechanical changes in crosslinked collagen gels are caused by the microstructural mechanism of increased resistance to fibril rotation.

Age-related changes in material behavior of porcine mitral and aortic valves and correlation to matrix composition

Recent studies showing significant changes in valvular matrix composition with age offer design criteria for age-specific tissue-engineered heart valves. However, knowledge regarding aging-related changes in valvular material properties is limited. Therefore, 6-week, 6-month, and 6-year-old porcine aortic valves (AV) and mitral valves (MV) were subjected to uniaxial tensile testing. In addition to standard material parameters, the radius of transition curvature (RTC) was measured to assess the acuteness of the transition region of the tension-strain curve. Radially, the MV had greater stiffness and a smaller RTC compared with the AV. Circumferentially, the center of the MV anterior leaflet (MVAC) had the highest stiffness (MVAC > AV > MV free edge [MVF]), greater stress relaxation (MVAC > MVF/AV), lowest extensibility (MVAC < AV < MVF), and smaller RTC compared with MVF (AV < MVAC < MVF). AV and MV radial strips had a larger RTC compared with circumferential strips. Aging elevated stiffness for MV and AV radial and circumferential strips, elevated stress relaxation in AV and MVF circumferential strips, and increased RTC for MV radial and MVF circumferential strips. In conclusion, there are significant age-related differences in the material properties of heart valves, which parallel differences in tissue composition and structure, likely impact valve function, and highlight the need for age-specific design goals for tissue-engineered heart valves.

Biocompatibility of Acellular Human Pericardium

BACKGROUND

Previous studies have shown successful decellularization of human pericardium without affecting the major structural components and strength of the matrix. The aim of this study was to assess the biocompatibility and reseeding potential of the acellular human pericardial scaffold.

MATERIALS AND METHODS

Pericardia were treated sequentially with hypotonic buffer, sodium dodecyl sulfate, and a nuclease solution. The presence of cellular attachment factors after decellularization was evaluated using immunohistochemistry. The scaffold was seeded with dermal fibroblasts and cellular attachment to and numbers of cells penetrating were assessed over time. Biocompatibility was also evaluated following subcutaneous implantation into a mouse model for three months.

RESULTS

After decellularization, the scaffold stained positively for fibronectin, but collagen IV and laminin staining was reduced. Seeded fibroblasts attached to the mesothelial surface and were visualized in the tissue within a week of seeding. The majority of fibroblasts in the tissue were viable and there was evidence of remodeling of the matrix. Analysis of the explanted tissues from mice showed that fresh/frozen and glutaraldehyde-fixed pericardia were encapsulated with a thick layer of inflammatory cells and fibrous tissue. In contrast, the decellularized scaffold was infiltrated with myofibroblasts, CD34+ cells and macrophages, indicating a healthy repair process. Compared with the glutaraldehyde-fixed tissue, the calcium content of the fresh/frozen and decellularized pericardia was negligible.

CONCLUSIONS

The pericardial scaffold was biocompatible in vitro and in the mouse model in vivo.

Bioprosthetic heart valve heterograft biomaterials: structure, mechanical behavior and computational simulation

The present review surveys significant developments in the biomechanical characterization and computational simulation of biologically derived chemically cross-linked soft tissues, or 'heterograft' biomaterials, used in replacement bioprosthetic heart valve (BHV). A survey of mechanical characterization techniques, relevant mechanical properties and computational simulation approaches is presented for both the source tissues and cross-linked biomaterials. Since durability remains the critical problem with current bioprostheses, changes with the mechanical behavior with fatigue are also presented. Moreover, given the complex nature of the mechanical properties of heterograft biomaterials it is not surprising that most constitutive (stress-strain) models, historically used to characterize their behavior, were oversimplified. Simulations of BHV function utilizing these models have inevitably been inaccurate. Thus, more recent finite element simulations utilizing nonlinear constitutive models, which achieve greater model fidelity, are reviewed. An important conclusion of this review is the need for accurate constitutive models, rigorously validated with appropriate experimental data, in order that the design benefits of computational models can be realized. Finally, for at least the coming 20 years, BHVs fabricated from heterograft biomaterials will continue to be extensively used, and will probably remain as the dominant valve design. We should thus recognize that rational, scientifically based approaches to BHV biomaterial development and design can lead to significantly improved BHV, over the coming decades, which can potentially impact millions of patients worldwide with heart valve disease.

Chemical treatment and tissue selection: factors that influence the mechanical behaviour of porcine pericardium

Calcification and mechanical failure are the major causes of the loss of cardiac bioprostheses. The chemical treatments used to stabilize the tissue employed are considered to play a fundamental role in the development of these two phenomena, although the problem is multifactorial and the underlying causes are yet to be fully identified. Currently, there is an ongoing search for chemical treatments capable of reducing or eliminating the process of calcification while preserving the mechanoelastic characteristics of the tissue. One of the approaches to this effort is the elimination of the phospholipid component from the biological tissue employed in prosthesis construction. There is evidence that this component may be responsible for the precipitation of calcium salts. The present study compares two delipidating chemical treatments involving chloroform/methanol and sodium dodecyl sulfate (SDS) with the use of glutaraldehyde (GA) alone. For this purpose, porcine pericardial tissue was subjected to tensile strength testing employing a hydraulic simulator. A total of 234 samples were studied 90 treated with GA, 72 treated with chloroform/methanol and 72 treated with SDS. The mean breaking strength was significantly higher in the samples treated with GA (between 43.29 and 63.01 MPa) when compared with those of tissue treated with chloroform/methanol (29.92-42.30 MPa) or with SDS (13.49-19.06 MPa). In a second phase of the study, selection criteria based on morphological and mechanical factors were applied to the pericardial membranes employing a system of paired samples. The mathematical analysis of the findings in one fragment will aid in determining the mechanical behavior of its adjacent twin sample. In conclusion, the anticalcification chemical treatments tested in the experimental model conferred a lesser mechanical resistance than that obtained with GA. On the other hand, the utilization of paired samples was found to be useful in the prediction of the mechanical behavior of porcine pericardial tissue. Nevertheless, in order for our method of selection to be considered the most adequate approach, it will be necessary to validate these findings in dynamic studies involving a real, functional model.

Founder's Award, 25th Annual Meeting of the Society for Biomaterials, perspectives. Providence, RI, April 28-May 2, 1999. Tissue heart valves: current challenges and future research perspectives

Substitute heart valves composed of human or animal tissues have been used since the early 1960s, when aortic valves obtained fresh from human cadavers were transplanted to other individuals as allografts. Today, tissue valves are used in 40% or more of valve replacements worldwide, predominantly as stented porcine aortic valves (PAV) and bovine pericardial valves (BPV) preserved by glutaraldehyde (GLUT) (collectively termed bioprostheses). The principal disadvantage of tissue valves is progressive calcific and noncalcific deterioration, limiting durability. Native heart valves (typified by the aortic valve) are cellular and layered, with regional specializations of the extracellular matrix (ECM). These elements facilitate marked repetitive changes in shape and dimension throughout the cardiac cycle, effective stress transfer to the adjacent aortic wall, and ongoing repair of injury incurred during normal function. Although GLUT bioprostheses mimic natural aortic valve structure (a) their cells are nonviable and thereby incapable of normal turnover or remodeling ECM proteins; (b) their cuspal microstructure is locked into a configuration which is at best characteristic of one phase of the cardiac cycle (usually diastole); and (c) their mechanical properties are markedly different from those of natural aortic valve cusps. Consequently, tissue valves suffer a high rate of progressive and age-dependent structural valve deterioration resulting in stenosis or regurgitation (>50% of PAV overall fail within 10-15 years; the failure rate is nearly 100% in 5 years in those <35 years old but only 10% in 10 years in those >65). Two distinct processes-intrinsic calcification and noncalcific degradation of the ECM-account for structural valve deterioration. Calcification is a direct consequence of the inability of the nonviable cells of the GLUT-preserved tissue to maintain normally low intracellular calcium. Consequently, nucleation of calcium-phosphate crystals occurs at the phospholipid-rich membranes and their remnants. Collagen and elastin also calcify. Tissue valve mineralization has complex host, implant, and mechanical determinants. Noncalcific degradation in the absence of physiological repair mechanisms of the valvular structural matrix is increasingly being appreciated as a critical yet independent mechanism of valve deterioration. These degradation mechanisms are largely rationalized on the basis of the changes to natural valves when they are fabricated into a tissue valve (mentioned above), and the subsequent interactions with the physiologic environment that are induced following implantation. The "Holy Grail" is a nonobstructive, nonthrombogenic tissue valve which will last the lifetime of the patient (and potentially grow in maturing recipients). There is considerable activity in basic research, industrial development, and clinical investigation to improve tissue valves. Particularly exciting in concept, yet early in practice is tissue engineering, a technique in which an anatomically appropriate construct containing cells seeded on a resorbable scaffold is fabricated in vitro, then implanted. Remodeling in vivo, stimulated and guided by appropriate biological signals incorporated into the construct, is intended to recapitulate normal functional architecture.

Assessment of pericardium in cardiac bioprostheses. A review

Cardiac valve bioprostheses are assessed in terms of their present and future clinical utility. The problems concerning durability basically involve early failure due to tears in the valve leaflets and late failure mainly associated with calcification of the biological tissue. New strategies for selection and chemical treatment of the biomaterials employed are analyzed, and the available knowledge regarding their mechanical behavior is reviewed. It is concluded that the durability of these devices, and thus their successful use in the future, depends on the knowledge of the interactions among the different biomaterials of which they are composed, the development of new materials, and the engineering design applied in their construction.

The chemical protecting group concept applied in crosslinking of natural tissues with glutaraldehyde acetals

This work describes the results of the controlled crosslinking of collagen matrices by glutaraldehyde based on a double protection strategy, glutaraldehyde acetals and lysine protonation due to the acidic conditions of acetal formation. Materials crosslinked by this approach were characterized by thermal stability comparable to those obtained by conventional procedures with mechanical properties expected for bioprosthesis manufacture and with a higher stability toward collagenase hydrolysis. The integrity of the microfibrillar structure was confirmed by optical and scanning electronic microscopy. The results indicate that the glutaraldehyde acetals procedure may be of potential use for the crosslinking of bovine pericardium used in the manufacture of bioprosthetic devices. Advantages may be related to the production of materials with homogeneous crosslinking distributions, associated with better definition in the nature of the chemical link that they introduce, due to a better distribution of glutaraldehyde within the tissue matrix before the crosslinking reaction is allowed to occur. As a result, materials with improved biological and mechanical properties are expected.

Viscoelasticity of dynamically fixed bioprosthetic valves. II. Effect of glutaraldehyde concentration

OBJECTIVE

We have previously shown the benefits of dynamic fixation over conventional static fixation of bioprosthetic valves. In an attempt to increase the durability of bioprosthetic heart valves, we explored the benefit of low-concentration glutaraldehyde dynamic fixation.

METHODS

Pig aortic valves obtained fresh from the abattoir and excised with the entire root were dynamically fixed in glutaraldehyde phosphate buffer solutions varying in concentration from 0.05% to 2.5%. Denaturation temperatures were measured and mechanical testing was performed at low (3 mm/sec) to high physiologic rates (30 mm/sec) at 37 degrees C in isotonic modified Hanks solution.

RESULTS

When fixed dynamically in 0.05% glutaraldehyde solution for 24 hours, the tissue reached a degree of cross-linking (denaturation temperature = 82.8 degrees +/- 0.6 degree C) significantly higher than that obtained for 0.05% static fixation (denaturation temperature = 79.3 degrees +/- 0.9 degree C) (p < 0.05) but similar to that for conventional static fixation in 0.5% glutaraldehyde solution (denaturation temperature = 83.5 degrees +/- 0.3 degree C). After fixation in low-concentration glutaraldehyde (0.05%), final relaxation slopes and moduli in the circumferential direction were significantly higher than those for the statically fixed tissue but similar to those for the fresh tissue. However, both dynamic and static fixation had the effect of increasing tissue extensibility to similar extents in both directions, irrespective of glutaraldehyde concentration.

CONCLUSIONS

Dynamic glutaraldehyde fixation of a porcine aortic valve at lower concentrations resulted in a better degree of cross-linking and a material with biomechanical properties that more closely mimic those of natural heart valve tissue.