Dextran modified gold surfaces for surface plasmon resonance sensors: immunoreactivity of immobilized antibodies and antibody-surface interaction studies

Detection of Antibodies against Hepatitis A Virus (HAV) by a Surface Plasmon Resonance (SPR) Biosensor: A New Diagnosis Tool Based on the Major HAV Capsid Protein VP1 (SPR-HAVP1)

Hepatitis A (HA) is an acute human infectious disease caused by a positive single-stranded RNA virus (HAV). It is mainly acquired through the fecal–oral route and is primarily spread by contact between people and exposure to contaminated water and food. Recently, large outbreaks of HA have been reported by low and moderate endemicity countries, emphasizing its importance in public health and the need for rapid and large-scale diagnostic tests to support public health decisions on HA. This work proposes a new tool for HAV diagnosis based on the association of surface plasmonic resonance with major capsid protein VP1 (SPR-HAVP1 assay), detecting IgM antibodies for HAV in human serum samples. Structural analyses of VP1 B-lymphocyte epitopes showed continuous and discontinuous epitopes. The discontinuous epitopes were identified in the N-terminal region of the VP1 protein. Both epitope types in the VP1 protein were shown by the reactivity of VP1 in native and denaturing conditions to IgM anti-HAV, which was favorable to tests of VP1 in the SPR assays. SPR-HAVP1 assays showed good performance in the detection of IgM polyclonal antibody anti-HAV. These assays were performed using a COOH5 sensor chip functionalized with VP1 protein. The sensorgram record showed a significant difference between positive and negative serum samples, which was confirmed by analysis of variation of initial and final dissociation values through time (ΔRUd/t). The data gathered here are unequivocal evidence that the SPR-HAVP1 strategy can be applied to detect IgM antibodies in human serum positive to the HAV. This is a new tool to be explored to diagnose human HAV infections.

Monitoring bioactive and total antibody concentrations for continuous process control by surface plasmon resonance spectroscopy

Monoclonal antibodies have become an increasingly important part of fundamental research and medical applications. To meet the high market demand for monoclonal antibodies in the biopharmaceutical sector, industrial manufacturing needs to be achieved by large scale, highly productive and consistent production processes. These are subject to international guidelines and have to be monitored intensely due to high safety standards for medical applications. Surface plasmon resonance spectroscopy - a fast, real-time, and label-free bio-sensing method - represents an interesting alternative to the quantification of monoclonal antibody concentrations by enzyme-linked immunosorbent assay during monoclonal antibody production. For the application of monitoring bioactive and total monoclonal antibody concentrations in cell culture samples, a surface plasmon resonance assay using a target-monoclonal antibody model system was developed. In order to ensure the subsequent detection of bioactive monoclonal antibody concentrations, suitable immobilization strategies of the target were identified. A significant decrease of the limit of detection was achieved by using an adapted affinity method compared to the commonly used amine coupling. Furthermore, the system showed limit of detection in the low ng/mL range similar to control quantifications by enzyme-linked immunosorbent assay. Moreover, the comparison of total to bioactive monoclonal antibody concentrations allows analysis of antibody production efficiency. The development of an alternative quantification system to monitor monoclonal antibody production was accomplished using surface plasmon resonance with the advantage of low analyte volume, shorter assay time, and biosensor reusability by target-layer regeneration. The established method provides the basis for the technical development of a surface plasmon resonance-based system for continuous process monitoring.

A surface plasmon resonance assay for characterisation and epitope mapping of anti-GLP-1 antibodies

The incretin hormone glucagon-like peptide-1 (GLP-1) has been subject to substantial pharmaceutical research regarding the treatment of type 2 diabetes mellitus. However, quantification of GLP-1 levels remains complicated due to the low circulation concentration and concurrent existence of numerous metabolites, homologous peptides, and potentially introduced GLP-1 receptor agonists. Surface plasmon resonance (SPR) facilitates real-time monitoring allowing a more detailed characterisation of the interaction compared with conventional enzyme-linked immunosorbent assays (ELISA). In this paper, we describe the development of the first SPR assays for characterisation of anti-GLP-1 antibodies for ELISA purposes. Binding responses were obtained on covalently immobilised anti-GLP-1 antibodies at 12°C, 25°C, and 40°C and fitted to a biomolecular (1:1) interaction model showing association rates of 1.01 × 10³ to 4.54 × 10³  M^-1  s^-1 and dissociation rates of 3.56 × 10^-5 to 1.56 × 10^-3  s^-1 leading to affinities of 35.2 to 344 nM, depending on the temperature. Determination of thermodynamic properties revealed an enthalpy driven interaction (ΔH < ΔS < 0) with higher affinities at lower temperatures due to the formation and stabilisation of hydrogen bonds within the binding site primarily composed of polar amino acids (ΔC_p  < 0). Pair-wise epitope mapping was performed on captured anti-GLP-1 antibodies followed by subsequent interaction with GLP-1 (7-36) and other anti-GLP-1 antibodies. A global evaluation of every binding response led to an epitope map elucidating the potential of various anti-GLP-1 antibody pairs for sandwich ELISA and hence pinpointing the optimal antibody combinations. The SPR assays proved capable of providing vital information for ELISA development endorsing it as a useful optimisation tool.

Electrochemical and surface plasmon insulin assays on clinical samples

Diabetes is a complex immune disorder that requires extensive medical care beyond glycemic control. Recently, the prevalence of diabetes, particularly type 1 diabetes (T1D), has significantly increased from 5% to 10%, and this has affected the health-associated complication incidences in children and adults. The 2012 statistics by the American Diabetes Association reported that 29.1 million Americans (9.3% of the population) had diabetes, and 86 million Americans (age ≥20 years, an increase from 79 million in 2010) had prediabetes. Personalized glucometers allow diabetes management by easy monitoring of the high millimolar blood glucose levels. In contrast, non-glucose diabetes biomarkers, which have gained considerable attention for early prediction and provide insights about diabetes metabolic pathways, are difficult to measure because of their ultra-low levels in blood. Similarly, insulin pumps, sensors, and insulin monitoring systems are of considerable biomedical significance due to their ever-increasing need for managing diabetic, prediabetic, and pancreatic disorders. Our laboratory focuses on developing electrochemical immunosensors and surface plasmon microarrays for minimally invasive insulin measurements in clinical sample matrices. By utilizing antibodies or aptamers as the insulin-selective biorecognition elements in combination with nanomaterials, we demonstrated a series of selective and clinically sensitive electrochemical and surface plasmon immunoassays. This review provides an overview of different electrochemical and surface plasmon immunoassays for insulin. Considering the paramount importance of diabetes diagnosis, treatment, and management and insulin pumps and monitoring devices with focus on both T1D (insulin-deficient condition) and type 2 diabetes (insulin-resistant condition), this review on insulin bioassays is timely and significant.

Wide dynamic range of surface-plasmon-resonance-based assay for hepatitis B surface antigen antibody optimal detection in comparison with ELISA

Limit of detection (LOD), limit of quantification, and the dynamic range of detection of hepatitis B surface antigen antibody (anti-HBs) using a surface plasmon resonance (SPR) chip-based approach with Pichia pastoris-derived recombinant hepatitis B surface antigen (HBsAg) as recognition element were established through the scouting for optimal conditions for the improvement of immobilization efficiency and in the use of optimal regeneration buffer. Recombinant HBsAg was immobilized onto the sensor surface of a CM5 chip at a concentration of 150 mg/L in sodium acetate buffer at pH 4 with added 0.6% Triton X-100. A regeneration solution of 20 mM HCl was optimally found to effectively unbind analytes from the ligand, thus allowing for multiple screening cycles. A dynamic range of detection of ∼0.00098-0.25 mg/L was obtained, and a sevenfold higher LOD, as well as a twofold increase in coefficient of variance of the replicated results, was shown as compared with enzyme-linked immunosorbent assay (ELISA). Evaluation of the assay for specificity showed no cross-reactivity with other antibodies tested. The ability of SPR chip-based assay and ELISA to detect anti-HBs in human serum was comparable, indicating that the SPR chip-based assay with its multiple screening capacity has greater advantage over ELISA.

Integrating plasmonic diagnostics and microfluidics

Plasmonics is generally divided into two categories: surface plasmon resonance (SPR) of electromagnetic modes propagating along a (noble) metal/dielectric interface and localized SPRs (LSPRs) on nanoscopic metallic structures (particles, rods, shells, holes, etc.). Both optical transducer concepts can be combined with and integrated in microfluidic devices for biomolecular analyte detections, with the benefits of small foot-print for point-of-care detection, low-cost for one-time disposal, and ease of being integrated into an array format. The key technologies in such integration include the plasmonic chip, microfluidic channel fabrication, surface bio-functionalization, and selection of the detection scheme, which are selected according to the specifics of the targeting analytes. This paper demonstrates a few examples of the many versions of how to combine plasmonics and integrated microfluidics, using different plasmonic generation mechanisms for different analyte detections. One example is a DNA sensor array using a gold film as substrate and surface plasmon fluorescence spectroscopy and microscopy as the transduction method. This is then compared to grating-coupled SPR for poly(ethylene glycol) thiol interaction detected by angle interrogation, gold nanohole based LSPR chip for biotin-strepavidin detection by wavelength shift, and gold nanoholes/nanopillars for the detection of prostate specific antigen by quantum dot labels excited by the LSPR. Our experimental results exemplified that the plasmonic integrated microfluidics is a promising tool for understanding the biomolecular interactions and molecular recognition process as well as biosensing, especially for on-site or point-of-care diagnostics.

Site-specific and covalent attachment of his-tagged proteins by chelation assisted photoimmobilization: a strategy for microarraying of protein ligands

A novel strategy for site-specific and covalent attachment of proteins has been developed, intended for robust and controllable immobilization of histidine (His)-tagged ligands in protein microarrays. The method is termed chelation assisted photoimmobilization (CAP) and was demonstrated using human IgG-Fc modified with C-terminal hexahistidines (His-IgGFc) as the ligand and protein A as the analyte. Alkanethiols terminated with either nitrilotriacetic acid (NTA), benzophenone (BP), or oligo(ethylene glycol) were synthesized and mixed self-assembled monolayers (SAMs) were prepared on gold and thoroughly characterized by infrared reflection absorption spectroscopy (IRAS), ellipsometry, and contact angle goniometry. In the process of CAP, NTA chelates Ni(2+) and the complex coordinates the His-tagged ligand in an oriented assembly. The ligand is then photoimmobilized via BP, which forms covalent bonds upon UV light activation. In the development of affinity biosensors and protein microarrays, site-specific attachment of ligands in a fashion where analyte binding sites are available is often preferred to random coupling. Analyte binding performance of ligands immobilized either by CAP or by standard amine coupling was characterized by surface plasmon resonance in combination with IRAS. The relative analyte response with randomly coupled ligand was 2.5 times higher than when site-specific attachment was used. This is a reminder that also when immobilizing ligands via residues far from the binding site, there are many other factors influencing availability and activity. Still, CAP provides a valuable expansion of protein immobilization techniques since it offers attractive microarraying possibilities amenable to applications within proteomics.

Impact of particulate antigens, such as Bacillus anthracis, on the uniformity of response across a biosensor flow cell as determined by GC-SPR

Biosensors are desired for the detection of a wide range of analytes in various scenarios, for example environmental monitoring for biological threats, from toxins to viruses and bacteria. Ideally a single sensor will be capable of simultaneous multianalyte detection. The varying nature, and in particular disparate size, of such a variety of analytes poses a significant challenge in the development of effective high-confidence instruments. Many existing biosensors employ functionalized flow cells in which spatially defined arrays of surface-immobilized recognition elements, such as antibodies, specifically capture their analyte of interest. To function optimally, arrays should provide equivalent responses for equivalent events across their active area. Experimental data obtained using a grating coupled surface plasmon resonance (GC-SPR) instrument, the BIAcore Flexchip, have revealed differences in response behaviors between proteinaceous and particulate analytes. In particular, the magnitude of responses seen with Bacillus anthracis spores appears to be influenced by shear and gravitational effects while those from soluble proteins are more uniform. We have explored this dependence to understand its fundamental impact on the successful implementation of multianalyte environmental biological detection systems.

Analysis of C-reactive protein on amide-linked N-hydroxysuccinimide-dextran arrays with a spectral surface plasmon resonance biosensor for serodiagnosis

A new label-free array system using amide-linked (AL) NHS-dextran and a spectral SPR biosensor are presented for the high-throughput analysis of C-reactive protein (CRP) in human sera. The AL NHS-dextran layer on the surface of gold arrays was composed of an amide linkage between NHS-modified carboxymethyl-dextran and amine-modified 11-mercaptoundecanoic acid. The topology of the AL NHS-dextran layer was analyzed by atomic force microscopy, and it was found to be superior to the previously used epoxide-linked carboxymethyl-dextran layer in its immobilization of proteins. Specific immunoreactions and a dose-dependent increase of SPR signals were demonstrated on the AL NHS-dextran layer. Then, the label-free array system was successfully applied to the rapid analysis of CRP in 120 human sera. CRP levels in human sera determined by the array-based spectral SPR biosensor showed a good correlation with those determined by the latex-enhanced turbidimetry immunoassay (n = 120, r = 0.945, p < 0.0001). Thus, the array-based spectral SPR biosensor based on the AL NHS-dextran surface is a potential system for rapid and label-free serodiagnosis of human diseases.

DNA–DNA interaction on dendron-functionalized sol–gel silica films followed with surface plasmon fluorescence spectroscopy

Since we observed that dendron-assembled surface provided high single nucleotide polymorphism discrimination efficiency for DNA microarrays, and that the binding yield for streptavidin increased when biotin was immobilized on top of it, the nanoscale-controlled surface is examined for surface plasmon field-enhanced fluorescence spectroscopy (or SPFS). Firstly, a silica film was coated onto a gold substrate using the sol-gel technique, followed by the covalent immobilization of a layer of second-generation dendrons with a DNA catcher strand at their apex. The thickness of the inorganic interlayer (d=33 nm) was effectively suppressing fluorescence quenching. Thus, the kinetics and affinity characteristics of DNA hybridization could be investigated very sensitively by SPFS. The kinetic rate constants found for DNA hybridization on the dendron-modified surface were larger than those reported for a streptavidin-modified surface by one order of magnitude, except for dissociation rate constant for a single mismatched case. In addition, we observed that the DNA on the cone-shaped linker maintained its capability to capture DNA target strands even after extended storage at ambient conditions.

Piezoelectric biosensors: Strategies for coupling nucleic acids to piezoelectric devices

The development of a piezoelectric biosensor based on nucleic acids interaction is presented focusing on the methodology for probe immobilization. This is a key step in any DNA biosensor development. Often, the detection limits and, in general, the analytical performances of the biosensor can be improved by optimizing the immobilization of the receptor on the transducer surface. DNA must be attached to the solid support, retaining native conformation, and binding activity. This attachment must be stable over the course of a binding assay and, in addition, sufficient binding sites must be presented to the solution phase to interact with the analyte. In this paper, the optimization of the coating of the gold quartz crystal surface, to immobilize an oligonucleotide probe, is reported. Two immobilization procedures are illustrated in details with a comparison regarding the immobilization of the probe, the detection of the hybridization reaction, and the possibility of regeneration. The two procedures are based on the use of biotinylated or thiolated DNA probes. Specific applications will be also presented.

Direct immobilisation of DNA probes for the development of affinity biosensors

An immobilisation procedure based on the direct coupling of thiolated probes (Probe-C6-SH) to bare gold sensor surfaces has been compared with a reference immobilisation method, based on the coupling of biotinylated probes onto a streptavidin-coated dextran-modified surface. The instrumentations used were a quartz crystal microbalance (QCM) and the optical instruments Biacore X and Spreeta based on surface plasmon resonance (SPR). The performances of the DNA-based sensors resulting from direct coupling of thiolated DNA probes onto electrodes of quartz crystals or gold SPR-chips have been studied in terms of the main analytical parameters, i.e. selectivity, sensitivity, reproducibility, etc. In particular, the two immobilisation approaches have been applied to the analysis of oligonucleotides, DNA amplified by polymerase chain reaction (PCR) and genomic DNA enzymatically digested.

Microfluidic enzyme immunosensors with immobilised protein A and G using chemiluminescence detection

Affinity proteins were covalently immobilised on silicon microchips with overall dimensions of 13.1 x 3.2 mm, comprising 42 porous flow channels of 235 microm depth and 25 microm width, and used to develop microfluidic immunosensors based on horseradish peroxidase (HRP), catalysing the chemiluminescent oxidation of luminol/p-iodophenol (PIP). Different hydrophilic polymers with long flexible chains (polyethylenimine (PEI), dextran (DEX), polyvinyl alcohol, aminodextran) and 3-aminopropyltriethoxysilane (APTS) were employed for modification of the silica surfaces followed by attachment of protein A or G. The resulting immunosensors were compared in an affinity capture assay format, where the competition between the labelled antigen and the analyte for antibody-binding sites took place in the bulk of the solution. The formed immunocomplexes were then trapped by the microchip affinity capture support and the amount of bound tracer was monitored by injection of luminol, PIP and H2O2. All immunosensors were capable of detecting atrazine at the sub-microg l(-1) level. The most sensitive assays were obtained with PEI and DEX polymer modified supports and immobilised protein G, with limits of detection of 0.006 and 0.010 microg l(-1), and IC50 values of 0.096 and 0.130 microg l(-1), respectively. The protein G based immunosensors were regenerated with 0.4 M glycine-HCl buffer pH 2.2, with no loss of activity observed for a storage and operating period of over 8 months. To estimate the applicability of the immunosensors to the analysis of real samples, PEI and DEX based protein G microchips were used to detect atrazine in surface water and fruit juice, spiked with known amounts of the atrazine, giving recovery values of 87-102 and 88-124% at atrazine fortification levels of 0.5-3 and 80-240 microg l(-1), respectively.

Improved procedures for immobilisation of oligonucleotides on gold-coated piezoelectric quartz crystals

The high sensitivity and specificity of DNA hybridisation techniques makes them powerful tools for environmental or clinical analysis. This work describes the development of a DNA piezoelectric biosensor for the detection of the hybridisation reaction. Attention was focused on the choice of the coating chemistry that could be used for the immobilisation of oligonucleotides onto the gold surface of the quartz crystal. Four immobilisation procedures were tested and compared considering the amount of immobilised probe, the extent of the hybridisation reaction, the possibility of regeneration and the absence of non-specific adsorption. All the experiments were performed with oligonucleotides of 25 bases (probe, target and non-complementary oligonucleotide). The four coating methods were all based on the use of self-assembled monolayers (SAM). Three of them employed the interaction between streptavidin and biotin for the immobilisation of a biotinylated probe. Results indicated that immobilisation of a biotinylated probe on streptavidin linked to a layer of carboxylated dextran provides higher sensitivity for the detection of the hybridisation reaction, absence of non-specific adsorption and a higher stability with respect to the regeneration step.

A novel aldehyde dextran sulfonate matrix for affinity biosensors

Aldehyde dextran sulfonate (ADS), a modified oligosaccharide polymer, was used to prepare a new matrix structure for affinity biosensors. The principal difference between the ADS matrix and similar structures developed previously results from presence of two active functional groups in the matrix, namely, aldehyde and sulfonate. These groups perform two different functions in the matrix. The aldehyde group is responsible for covalent bonding in the biomaterials, and the negatively charged sulfonate group provides electrostatic attraction of the positively charged biomolecules. By varying the ratio between the aldehyde and sulfonate groups in the matrix, one can control contributions from the two binding modes (covalent and electrostatic). A number of oligosaccharides, such as simple dextran, aldehyde dextran (AD), aldehyde dextran sulfonate (ADS) and aldehyde ethylcellulose (AEC), were used for preparation of matrix structures. The properties of the obtained matrices were analysed and compared. Surface plasmon resonance (SPR) was used as the main technique to characterize the matrix structures.

Covalent bound sensing layers on surface acoustic wave (SAW) biosensors

This paper reports on the development of immunosensors based on commercially available surface acoustic wave (SAW) devices working at 380 MHz. Approaches for coating the sensor surface with a sensing layer of receptive biomolecules are presented and discussed. It was found that the sensitivity strongly relates to the immobilization method. Additionally, the sensitivity can be influenced by the density of accessible biomolecules on the active sensing area. Usually, by most of the standard immobilization procedures, two-dimensional layers of receptive biomolecules are obtained. We present a three-dimensional layer, which provides a higher absolute amount of recognition molecules. A dextran layer is photoimmobilized to the sensor surface and the recognition molecules are covalently embedded into the dextran matrix. The feasibility of specific immunosensing is investigated using SAW sensors connected to a fluid handling system.

Synthesis of a series of oligo(ethylene glycol)-terminated alkanethiol amides designed to address structure and stability of biosensing interfaces

A strategy for the synthesis of a series of closely related oligo(ethylene glycol)-terminated alkanethiol amides (principally HS(CH(2))(m)CONH(CH(2)CH(2)O)(n)H; m = 2, 5, 11, 15, n = 1, 2, 4, 6, 8, 10, 12) and analogous esters has been developed. These compounds were made to study the structure and stability of self-assembled monolayers (SAMs) on gold in the prospect of designing new biosensing interfaces. For this purpose, monodisperse heterofunctional oligo(ethylene glycols) with up to 12 units were prepared. Selective monoacylation of the symmetrical tetra- and hexa(ethylene glycol) diols as their mesylates with the use of silver(I) oxide was performed. The synthetic approach was based on carbodiimide couplings of various oligo(ethylene glycol) derivatives to omega-(acetylthio) carboxylic acids via a terminal amino or hydroxyl function. SAM structures on gold were studied with respect to thickness, wettability (water contact angles approximately 30 degrees ), and conformation. A good fit was obtained for the relation between monolayer thickness (d) and the number of units in the oligo(ethylene glycol) chain (n): d = 2.8n + 21.8 (A). Interestingly, the corresponding infrared spectroscopy analysis showed a dramatic change in conformation of the oligomeric chains from all-trans (n = 4) to helical (n > or = 6) conformation. A crystalline helical structure was observed in the SAMs for n > 6.

Covalent photolinker-mediated immobilization of an intermediate dextran layer to polymer-coated surfaces for biosensing applications

A new method is presented for the covalent binding of dextran as an intermediate layer on surface acoustic wave (SAW) devices. For biosensing applications in aqueous media commercially available SAW devices require surface passivation to prevent corrosion of the aluminum device structures in electrolytes. Thin films of polyimide and parylene revealed exceptional passivation properties. They were used as a base for dextran immobilization. Covalent binding of dextran to polymer-coated surfaces was achieved by photoimmobilization. Aryldiazirine-functionalized bovine serum albumin served as the multifunctional light-activable linking agent (photolinker polymer). Dextran and photolinker polymer were mixed and photobonded to sensor surfaces. Essential photoimmobilization parameters were optimized. The binding of proteins to dextran applying carbodiimide chemistries was exemplified with antiurease antibodies and the feasibility of specific immunosensing was investigated on SAW sensors connected to a fluid handling system.

Immunoassay of fumonisins by a surface plasmon resonance biosensor

A surface plasmon resonance (SPR) immunosensor is developed to determine concentrations of the mycotoxin, fumonisin B1 (FB1), in spiked samples. Polyclonal antibodies produced against FB1 are adsorbed onto a thin gold film substrate, which is coupled to a glass prism in the Kretschmann configuration. The output beam of a planar light-emitting diode is focused through the prism to excite SPR at the surface of the gold film. When a sample containing FB1 is added to a cell on the outside of the gold film, the angular profile of reflected light intensity shifts. This changes the resonance angle and the reflected beam intensity at a selected angle, both of which are proportional to the FB1 concentration. After optimization of the antibody overlayer, a detection limit of 50 ng/mL is obtained for the direct assay with an analysis time under 10 min. Multiple sample additions and large-volume sample circulation can be used with the high-affinity antibodies to achieve lower detection limits.

Comparison of methods for immobilization to carboxymethyl dextran sensor surfaces by analysis of the specific activity of monoclonal antibodies

The authors have recently described the development of a carboxymethyl dextran-based sensor surface for biospecific interaction analysis by surface plasmon resonance. Ligands are immobilized via primary amine groups after activation of the carboxymethyl groups on the sensor surface with a mixture of N-hydroxysuccinimide and N-ethyl-N'-(dimethylaminopropyl) carbodiimide. Methods have now been developed for efficient immobilization via thiol/disulfide exchange, aldehyde coupling and biotin-avidin coupling. The specific activity of monoclonal antibodies immobilized by the four different methods was investigated by altering the immobilization conditions, e.g., activation time, protein concentration, ionic strength and the degree of modification, etc. Investigations have also been made concerning possible differences in the specific activity for antibodies immobilized using optimized conditions with respect to the four different chemistries. These studies show that, with the flexible carboxymethyl dextran matrix used here, the immobilization methods give rise to only minor differences in specific activity. Thus, with this solid support, a 'site directed' immobilization strategy for monoclonal antibodies has no advantage. In general the specific activity for optimized systems was approximately 75% for the binding of beta 2 mu-globulin to an immobilized monoclonal antibody directed against beta 2 mu-globulin. Reduced specific activities of immobilized antibodies induced by variation of the coupling conditions could be attributed to the deterioration of the active site of the antibody.

Immobilisation of IgG onto gold surfaces and its interaction with anti-IgG studied by surface plasmon resonance

The optical excitation of surface plasmon resonance (SPR) at a metal dielectric interface has been used to study the binding of immunoglobulin G (IgG) to gold and anti-IgG to immobilised IgG layers. In these studies both a monoclonal mouse and polyclonal sheep IgG were used as receptor layers for anti-IgG. The kinetics of binding were investigated by monitoring the reflectivity of light at an angle close to plasmon resonance. Both the initial rate of change and final reflectivity were measured during and after protein binding. The amount of protein bound to the surface was found to be less for the monoclonal mouse IgG compared to the polyclonal sheep IgG, these two IgG nominally being of the same dimensions and molecular weight. Further, anti-IgG binding produced greater changes in reflectivity than the initial IgG layers. By fitting the full angle-dependent reflectivity data to the Fresnel equation the effective protein layer thicknesses of IgG and anti-IgG as a function of concentration were determined. Differences in the effective thickness of the bound layer for the two IgG was observed, the mouse IgG having a thinner effective thickness compared with the sheep IgG. The limitations of direct binding of protein to metal surfaces in SPR biosensor applications are discussed.