Latest research progress of marine microbiological corrosion and bio-fouling, and new approaches of marine anti-corrosion and anti-fouling

Microalgae Film-Derived Water Evaporation-Induced Electricity Generator with Negative Carbon Emission

Water evaporation-induced electricity generators (WEGs) are regarded as one of the most promising solutions for addressing the increasingly severe environmental pollution and energy crisis. Owing to the potential carbon emission in the preparation process of WEGs, whether WEG represents a clean electricity generation technology is open to question. Here, a brand-new strategy is proposed for manufacturing negative carbon emission WEG (CWEG). In this strategy, the microalgae film is used as the electricity generation interface of WEG, which achieves a stable open-circuit voltage (Voc) of 0.25 V and a short-circuit current (Isc) of 3.3 µA. Since microalgae can capture carbon dioxide during its growing process, CWEG holds great promise to generate electricity without carbon emissions in the full life cycle compared with other WEGs. To the best of the author's knowledge, this is the first work using microalgae films to fabricate WEG. Therefore, it is believed that this work not only provides a new direction for designing high-efficiency and eco-friendly WEG but also offers an innovative approach to the resource utilization of microalgae.

Characterization of antibiofilm compound from marine sponge Stylissa carteri

The fouling phenomenon grabbed global attention and caused huge economic losses specifically in marine-related industries. Sessile behavior exposed the sponge to the risk of fouling. However, their bodies remained free from foulers, which were attributed to the chemical defense system. The objectives of this study were to determine the antibiofilm activity of the marine sponge, Stylissa carteri, and to characterize the isolated compound involved. The antibiofilm activity of S. carteri methanolic crude extract (MCE) and fractions was tested against biofilm-producing bacteria, Pseudomonas aeruginosa, using two different modes of crystal violet biofilm assays: preventive and detachment. Besides that, the disc-diffusion test was conducted to screen the antibacterial activity against gram-positive and gram-negative bacteria while a cytotoxicity assay was conducted on the HepG2 cell line. Bioassay-guided fractionation was carried out using vacuum liquid chromatography (VLC) and solid phase extraction using a C18 Sep-Pak Cartridge. The crystal compound was isolated and characterized through thin-layer chromatography (TLC), Fourier transform infrared (FTIR) spectroscopy, liquid chromatography-mass spectrometry (LCMS), and nuclear magnetic resonance (NMR) spectroscopy. The S. carteri MCE showed a promising result with a half-maximal inhibitory concentration (IC50) of 20.22 μg/mL in the preventive assay, while no IC50 was determined in the detachment assay since all inhibitions < 50%. The S. carteri MCE exhibited broad-spectrum antibacterial activity and displayed a non-cytotoxic effect. Fraction 4 from MCE of S. carteri (IC50 = 2.40 μg/mL) reduced the biofilm in the preventive assay at all concentrations and exhibited no antibacterial activity indicating the independence of antibiofilm from antibacterial properties. Based on the data obtained, an alkaloid named debromohymenialdisine (DBH) was identified from Fraction 4 of S. carteri MCE. In conclusion, S. carteri was able to reduce the establishment of the biofilm formed by P. aeruginosa and could serve as a prominent source of natural antifouling agents.

A bibliometric analysis of cellulose anti-fouling in marine environments

Marine biofouling poses significant challenges to maritime industries worldwide, affecting vessel performance, fuel efficiency, and environmental sustainability. These challenges demand innovative and sustainable solutions. In this review, the evolving landscape of cellulose-based materials for anti-fouling applications in marine environments is explored. Through a comprehensive bibliometric analysis, the current state of research is examined, highlighting key trends, emerging technologies, and geographical distributions. Cellulose, derived from renewable resources, offers a promising avenue for sustainable anti-fouling strategies due to its biodegradability, low toxicity, and resistance to microbial attachment. Recent advancements in cellulose-based membranes, coatings, and composites are discussed, showcasing their efficacy in mitigating biofouling while minimizing environmental impact. Opportunities for interdisciplinary collaboration and innovation are identified to drive the development of next-generation anti-fouling solutions. By harnessing the power of cellulose, progress towards cleaner, more sustainable oceans can be facilitated, fostering marine ecosystems and supporting global maritime industries.

The impact of alloying element Cu on corrosion and biofilms of 316L stainless steel exposed to seawater

Copper-containing stainless steel (SS) has been reported to mitigate biofilms in industrial and clinical environments. However, the impact of copper released from copper-containing SS in natural seawater on biofilms and corrosion is still unclear. In this study, three kinds of 316L SS were immersed in natural seawater for 6 months, and the pitting depth decreased in the order: 316L-Cu SS (annealed) > 316L SS > 316L-Cu SS (aged). The biofilm thickness and number of sessile cells on the surface of 316L-Cu SS (annealed) and 316L SS were similar but notably greater than those of 316L-Cu SS (aged). Furthermore, the results of the community analysis indicated that the addition of copper in 316L-Cu SS (aged) reduced the diversity and richness of the microbial community, resulting in a significant reduction in the number of genera constituting the biofilms. Copper ions exhibit a broad-spectrum bactericidal effect, effectively reducing the abundance of dominant populations and microbial genera in the biofilms, thereby mitigating pitting corrosion induced by microorganisms. In addition, the PCoA scatter plot showed that time also played an important role in the regulation of microbial community structure.

Superwettable surfaces and factors impacting microbial adherence in microbiologically-influenced corrosion: a review

Microbiologically-influenced corrosion (MIC) is a common operational hazard to many industrial processes. The focus of this review lies on microbial corrosion in the maritime industry. Microbial metal attachment and colonization are the critical steps in MIC initiation. We have outlined the crucial factors influencing corrosion caused by microorganism sulfate-reducing bacteria (SRB), where its adherence on the metal surface leads to Direct Electron Transfer (DET)-MIC. This review thus aims to summarize the recent progress and the lacunae in mitigation of MIC. We further highlight the susceptibility of stainless steel grades to SRB pitting corrosion and have included recent developments in understanding the quorum sensing mechanisms in SRB, which governs the proliferation process of the microbial community. There is a paucity of literature on the utilization of anti-quorum sensing molecules against SRB, indicating that the area of study is in its nascent stage of development. Furthermore, microbial adherence to metal is significantly impacted by surface chemistry and topography. Thus, we have reviewed the application of super wettable surfaces such as superhydrophobic, superhydrophilic, and slippery liquid-infused porous surfaces as "anti-corrosion coatings" in preventing adhesion of SRB, providing a potential avenue for the development of practical and feasible solutions in the prevention of MIC. The emerging field of super wettable surfaces holds significant potential for advancing efficient and practical MIC prevention techniques.

Seasonal variation in the biological succession of marine diatoms over 316L stainless steel in a coastal environment of Chile

Characterizing seasonal changes in diatom community profiles in coastal environments is scarce worldwide. Despite diatoms being prevalent in microfouling, their role in microbially influenced corrosion of metallic materials remains poorly understood. This study reports the effect of seasonal variations on the settlement of marine diatoms and corrosion of 316 L stainless steel surfaces exposed to Chilean coastal seawater. Electron microscopy imaging revealed a diverse assembly of diatoms, exhibiting pronounced differences at genus level between summer and winter seasons, with a significant delay in diatom settlement during winter. Electrochemical measurements indicated an active role of diatoms in increasing corrosion current during biofilm development. While the final diatom composition was similar irrespective of the season, the analyses of diatom assemblages over time differed, showing faster colonization when silicate and nitrate were available. This study lays the foundation for future research on the dominant season-specific genera of diatoms to unveil the microbial interactions that could contribute to corrosion and to evaluate their potential as bioindicators for alternative surveillance strategies.

Silicone-modified polyurea-interpenetrating polymer network fouling release coatings with excellent wear resistance property tailored to regulations

The invasion of alien species via marine organisms attaching to the surfaces of ship hulls is a growing problem. A number of countries have introduced corresponding regulations to combat ship biofouling. One effective way to solve this problem is to apply a fouling release coating with excellent wear resistance. In this study, a silicone-modified polyaspartic ester polyurea was synthesized by a simultaneous crosslinking polymerization. Polyaspartic ester polyurea is employed to form a tightly cross-linked network with excellent toughness and outstanding adhesion, while polydimethylsiloxane is used to form a relatively soft cross-linked network with low surface energy and surface elasticity modulus. Polyurea and silicone molecular chain lock onto each other to form interpenetrating polymer network (IPN) through their respective polymerization systems and cross-linking processes. The synergy between silicone and polyurea provides excellent mechanical properties as well as fouling release performance through the locking mechanism. This study provides a promising and universal strategy for the development of fouling release coatings with excellent wear resistance.

Marine antifouling properties of enzyme modified polyaniline coated stainless steel surface

On solid surfaces immersed in a liquid medium, a biofilm layer which is called biofouling formed over time by organic molecules and microorganisms. It is important to produce new eco-friendly ideas can prevent this undesired phenome. In this study, we focused on the antifouling performance of polyaniline (PANI), whose anticorrosive properties have been already known. The main purpose of this study was to immobilize hydrolytic enzymes that could break down biomolecules and microorganisms and how this would contribute to the antifouling performance of the PANI coating. When α-amylase, DNAse, glucose oxidase, α-chymotrypsin, lipase and pectinase enzymes immobilized into PANI that was synthesized in ammonium oxalate (PANIAO) and sodium salicylate (PANISS) electrolytes, α-amylase containing film (PANISS-A) showed the highest performance (76.5% antifouling activity). The surface properties after keeping in the Mediterranean Sea for 12 days were compared by digital photography, Scanning Electron microscope (SEM) and fluorescence microscope images, also with Energy Dispersive X-Ray (EDX) analysis and crystal violet staining. Carbohydrate and protein amounts and CFU (Colony Forming Units) values of biofilms formed on the surface for bare, PANISS and PANISS-A coupons after keeping 12 days in the Mediterranean Sea were determined. Vibrio species (V.harveyi, V.alginolyticus, V.parahaemolyticus) were detected in the biofilms by Matrix- Assisted Laser Desorption/Ionization Time of Flight Mass Spectrometry (MALDI-TOF MS) analysis.

Biofilms and beyond: a comprehensive review of the impact of Sulphate Reducing Bacteria on steel corrosion

Sulphate-reducing bacteria (SRB) are known to cause severe corrosion of steel structures in various industries, resulting in significant economic and environmental consequences. This review paper critically examines the impact of SRB-induced corrosion on steel, including the formation of SRB biofilms, the effect on different types of steel, and the various models developed to investigate this phenomenon. The role of environmental factors in SRB-induced corrosion, molecular techniques for studying SRBs, and strategies for mitigating corrosion are discussed. Additionally, the sustainability implications of SRB-induced corrosion and the potential use of alternative materials were explored. By examining the current state of knowledge on this topic, this review aims to provide a comprehensive understanding of the impact of SRB-induced corrosion on steel and identify opportunities for further research and development.

Microbially Influenced Corrosion of Steel in Marine Environments: A Review from Mechanisms to Prevention

Microbially influenced corrosion (MIC) is a formidable challenge in the marine industry, resulting from intricate interactions among various biochemical reactions and microbial species. Many preventions used to mitigate biocorrosion fail due to ignorance of the MIC mechanisms. This review provides a summary of the current research on microbial corrosion in marine environments, including corrosive microbes and biocorrosion mechanisms. We also summarized current strategies for inhibiting MIC and proposed future research directions for MIC mechanisms and prevention. This review aims to comprehensively understand marine microbial corrosion and contribute to novel strategy developments for biocorrosion control in marine environments.

Microbiologically influenced corrosion-more than just microorganisms

Microbiologically influenced corrosion (MIC) is a phenomenon of increasing concern that affects various materials and sectors of society. MIC describes the effects, often negative, that a material can experience due to the presence of microorganisms. Unfortunately, although several research groups and industrial actors worldwide have already addressed MIC, discussions are fragmented, while information sharing and willingness to reach out to other disciplines are limited. A truly interdisciplinary approach, which would be logical for this material/biology/chemistry-related challenge, is rarely taken. In this review, we highlight critical non-biological aspects of MIC that can sometimes be overlooked by microbiologists working on MIC but are highly relevant for an overall understanding of this phenomenon. Here, we identify gaps, methods, and approaches to help solve MIC-related challenges, with an emphasis on the MIC of metals. We also discuss the application of existing tools and approaches for managing MIC and propose ideas to promote an improved understanding of MIC. Furthermore, we highlight areas where the insights and expertise of microbiologists are needed to help progress this field.

Nano-CeO2-Loaded Polyzwitterionic Double-Network High-Strength Hydrogel for Highly Enhanced Synergistic Marine Antifouling

Although many antibiofouling materials have been developed based on either bacterial-killing or antiadhesion effects, the integration of both the effects in one material remains challenging for achieving highly enhanced synergistic antibiofouling. In this study, we have explored a nano-CeO2-loaded double-network hydrogel by introducing CeO2 nanorods into a polyzwitterionic hydrogel via a simple one-pot method for achieving highly efficient antifouling. First, the CeO2 nanorods dispersed in the hydrogel, as an outstanding nanozyme, have highly efficient bacterial-killing performance. Second, the superhydrophilic polyzwitterionic hydrogel provides a dense hydrated layer on the surface and subsequently excellent broad-spectrum antiadhesion behavior. Most importantly, the bacterial killing and antiadhesion of this hydrogel can work synergistically to largely improve the marine-antifouling performance. Moreover, the double-network structure of this hydrogel, including the covalently cross-linked polyzwitterion hard network and the physically cross-linked poly(vinyl alcohol) soft network, can provide greatly improved mechanical properties (2.44 MPa of tensile strength reaches and 21.87 MPa of compressive strength). As a result, among the existing marine-antifouling hydrogels, the CeO2-loaded polyzwitterionic double-network hydrogel can achieve outstanding antifouling performance, which can sustain for over 6 months in a real marine environment. This work provides a promising marine-antifouling hydrogel, which will also inspire antifouling research of a new strategy and materials.

Laser Shock Peening Improves the Corrosion Resistance of an E690 High-Strength Steel Cladding Layer

To investigate the effect of laser shock peening parameters on the corrosion resistance of an E690 high-strength steel cladding layer, NVE690 high-strength steel powder was selected for testing at various power densities of pulse lasers. The surface roughness and residual stress of the treated samples were measured, and the microstructure morphology of the sample surface was observed. The electrochemical corrosion tests were conducted with an electrochemical workstation to measure the electrometer polarization, obtain the impedance curve, and observe the electrochemical corrosion. As the laser power density increased, the surface grains of the E690 high-strength steel cladding layer continued to refine until nanocrystals formed, and the residual compressive stress on the surface increased. The residual compressive stress on the surface rendered the passivation film stable and dense; furthermore, the refinement of surface grains inhibited the initiation and propagation of microcracks. The positive shift of the corrosion potential increased from -1.004 to -0.771 V, the corrosion current density decreased from 114.5 to 5.41 μA/cm2, the radius of the impedance spectrum curve increased, and the peeling pits, as well as corrosion micropores on the surface, gradually became no longer evident after electrochemical corrosion. After laser shock treatment, the corrosion resistance of the cladding layer sample was substantially improved.

A novel all-organic microcapsule with excellent long-term antibacterial and anti-corrosion performances

This work successfully synthesized the salicylic acid@polyurea-formaldehyde (SA@PUF) microcapsules with PUF microcapsules as shell material and SA as core material. The loading content of SA in the PUF microcapsules was approximately 40 %. The SA@PUF microcapsules had excellent long-term antibacterial properties because the PUF microcapsules controlled the release of SA antifouling agents with the ability to induce reactive oxygen species generation and inactivate bacteria. The antibacterial efficiency of SA@PUF microcapsules after 35 days against Staphylococcus aureus and Pseudomonas aeruginosa remained at 80 % and 81 %, increased by 60 % and 62 % compared with pure SA, respectively. The impedance modulus at 0.01 Hz of the SA@PUF coating reached 5.51 GΩ cm², much higher than blank coating (2.55 GΩ cm²) and PUF coating (4.94 GΩ cm²), indicating that the anti-corrosion property of the SA@PUF coating was much better. This work would contribute to developing novel coatings with long-term antibacterial activity and excellent anti-corrosion performance.

Sustainable Secondary-Raw Materials, Natural Substances and Eco-Friendly Nanomaterial-Based Approaches for Improved Surface Performances: An Overview of What They Are and How They Work

To meet modern society’s requirements for sustainability and environmental protection, innovative and smart surface coatings are continually being developed to improve or impart surface functional qualities and protective features. These needs regard numerous different sectors, such as cultural heritage, building, naval, automotive, environmental remediation and textiles. In this regard, researchers and nanotechnology are therefore mostly devoted to the development of new and smart nanostructured finishings and coatings featuring different implemented properties, such as anti-vegetative or antibacterial, hydrophobic, anti-stain, fire retardant, controlled release of drugs, detection of molecules and mechanical resistance. A variety of chemical synthesis techniques are usually employed to obtain novel nanostructured materials based on the use of an appropriate polymeric matrix in combination with either functional doping molecules or blended polymers, as well as multicomponent functional precursors and nanofillers. Further efforts are being made, as described in this review, to carry out green and eco-friendly synthetic protocols, such as sol–gel synthesis, starting from bio-based, natural or waste substances, in order to produce more sustainable (multi)functional hybrid or nanocomposite coatings, with a focus on their life cycle in accordance with the circular economy principles.

Virtual Screening of a Library of Naturally Occurring Anthraquinones for Potential Anti-Fouling Agents

Marine biofouling is the undesired accumulation of organic molecules, microorganisms, macroalgae, marine invertebrates, and their by-products on submerged surfaces. It is a serious challenge for marine vessels and the oil, gas, and renewable energy industries, as biofouling can cause economic losses for these industries. Natural products have been an abundant source of therapeutics since the start of civilisation. Their use as novel anti-fouling agents is a promising approach for replacing currently used, harmful anti-fouling agents. Anthraquinones (AQs) have been used for centuries in the food, pharmaceutical, cosmetics, and paint industries. Citreorosein and emodin are typical additives used in the anti-fouling paint industry to help improve the global problem of biofouling. This study is based on our previous study, in which we presented the promising activity of structurally related anthraquinone compounds against biofilm-forming marine bacteria. To help uncover the anti-fouling potential of other AQ-related structures, 2194 compounds from the COCONUT natural products database were analysed. Molecular docking analysis was performed to assess the binding strength of these compounds to the LuxP protein in Vibrio carchariae. The LuxP protein is a vital binding protein responsible for the movements of autoinducers within the quorum sensing system; hence, interrupting the process at an early stage could be an effective strategy. Seventy-six AQ structures were found to be highly docked, and eight of these structures were used in structure-based pharmacophore modelling, resulting in six unique pharmacophore features.

Potential disruptive effects of copper-based antifouling paints on the biodiversity of coastal macrofouling communities

The expanded use of copper(I)-based antifouling paints (AF) has increased copper leaching into coastal environments, requiring attention and legislative restrictions for potential long-term effects on benthic populations. The ecological succession of macrofouling communities was analysed on wooden and stainless steel panels coated with four copper(I)-based AF (Paints A-D) immersed for 10 months in the Lagoon of Venice. With the exception of Paint B, which contained only copper(I) compounds and was based on hard-matrix technology, the other paints were based on self-polishing matrices and various booster biocides. The booster content was a mix of TBT compounds for Paint A, dichlofluanid for Paint C, Irgarol 1051, and chlorothalonil for Paint D. The macrofouling communities appeared dissimilar to those on the reference uncoated panels as regard the species richness, the coverage areas, and the biocoenosis structure. Generally, green algae, bryozoans, and barnacles were the most tolerant taxa and a negative species selection occurred for sponges, serpulids, and ascidians. Paints A and D showed the highest performance, and Paint D also prevented molluscs on wood panels. Paints B and C rapidly decreased their efficiency, the first probably due to the insoluble matrix with the highest biocidal leaching rate, and the second due to the presence of a booster with low toxicity. Paint B also inhibited red algae and molluscs, but Paint C did not reveal significant differences in types of species settlements with reference panels.

Characteristic and Mechanistic Investigation of Stress-Assisted Microbiologically Influenced Corrosion of X80 Steel in Near-Neutral Solutions

The behavior and mechanisms of the stress-assisted microbiologically influenced corrosion (MIC) of X80 pipeline steel induced by sulfate-reducing bacteria (SRB) were investigated using focused ion beam-scanning electron microscopy (FIB). Electrochemical results show that SRB and stress have a synergistic effect on the corrosion of X80 steel. SRB accelerated the transformation of Fe₃O₄ into iron-sulfur compounds and may have caused the film breakage of X80 steel products. The obtained FIB results provide direct evidence that SRB promotes the corrosion of X80 steel.

Accelerated biocorrosion of stainless steel in marine water via extracellular electron transfer encoding gene phzH of Pseudomonas aeruginosa

Microbiologically influenced corrosion (MIC) constantly occurs in water/wastewater systems, especially in marine water. MIC contributes to billions of dollars in damage to marine industry each year, yet the physiological mechanisms behind this process remain poorly understood. Pseudomonas aeruginosa is a representative marine electro-active bacterium, which has been confirmed to cause severe MIC on carbon steel through extracellular electron transfer (EET). However, little is known about how P. aeruginosa causes corrosion on stainless steel. In this study, the corrosivity of wild-type strain, phzH knockout, phzH complemented, and phzH overexpression P. aeruginosa mutants were evaluated to explore the underlying MIC mechanism. We found the accelerated MIC on 2205 duplex stainless steel (DSS) was due to the secretion of phenazine-1-carboxamide (PCN), which was regulated by the phzH gene. Surface analysis, Mott-Schottky test and H₂O₂ measurement results showed that PCN damaged the passive film by forming H₂O₂ to oxidize chromium oxide to soluble hexavalent chromium, leading to more severe pitting corrosion. The normalized corrosion rate per cell followed the same order as the general corrosion rate obtained under each experimental condition, eliminating the influence of the total amount of sessile cells on corrosion. These findings provide new insight and are meaningful for the investigation of MIC mechanisms on stainless steel. The understanding of MIC can improve the sustainability and resilience of infrastructure, leading to huge environmental and economic benefits.

The role of organic acid metabolites in geo-energy pipeline corrosion in a sulfate reducing bacteria environment

The dominant factors in Microbial Influenced Corrosion (MIC) are hard to determine because normally several individual species and their metabolites are involved, and, moreover, different metabolites may cause opposing effects. To address this problem, the effects of individual metabolites from different species should be elucidated when at the same time other metabolites are held constant. In this study, the role is investigated of simulated organic acid metabolites, namely, acetic and L–ascorbic acids, on corrosion of geo-energy pipelines (carbon steel) in a simulated Sulfate Reducing Bacteria (SRB) environment. The SRB environment is simulated using a calcium alginate biofilm, abiotic sulfide, CO₂, and NaCl brine. The electrochemical results show that both simulated organic acid metabolites accelerate corrosion in a simulated SRB environment. The results are further supported by electrochemical weight losses, kinetic corrosion activation parameters, multiple linear regression, ICP-OES, pH, and XRD. However, a comparison of electrochemical results with those published in the literature for a simulated SRB environment without acetic or L-ascorbic acid under similar experimental conditions shows that the presence of acetic in this study results in lower corrosion current densities while in presence of L-ascorbic acid results into higher corrosion current densities. This implies that acetic and L-ascorbic acids inhibit and accelerate corrosion, respectively. In addition, the results highlight that H₂S is a key role of corrosion in the presence of organic acid. The results of this study are important new and novel information on the role of acetic and L-ascorbic acids in corrosion of geo-energy pipelines in the SRB environment.

Bioinspired antifouling Fe-based amorphous coating via killing-resisting dual surface modifications

Fe-based amorphous coatings with outstanding corrosion resistance are promise for marine applications. However, these coatings encounter a great challenge of biofouling in marine environments. Inspired by the unique micro-nano hierarchical structure of shark skin with excellent antifouling properties, in this paper, we construct a bioinspired Fe-based amorphous coating with killing-resisting dual-effect via proper surface modifications, i.e., the modification with micro-patterned nanostructured Cu₂O fibers (killing effect), followed by the modification with superhydrophobic surface (resisting effect). As a result, the modified amorphous coating exhibits impressive antifouling properties, achieving 98.6% resistance to Nitzschia closterium f. minutissima, 87% resistance to Bovine serum albumin protein and 99.8% resistance to Pseudomonas aeruginosa, respectively. The remarkable antifouling performance is attributed to a synergistic antifouling mechanism from both resisting effect and killing effect, wherein the superhydrophobic surface provides a barrier to resist protein adsorption, while the patterned nanostructured Cu₂O fibers supply Cu⁺ ions to kill bacterial cells. In addition, the modified amorphous coating also exhibits excellent mechanical robustness, which ensures the durability of the Fe-based amorphous coating in practical services. This work may promote the development of new durable metal-based coatings integrated with anti-fouling and anti-corrosion properties.

Water- and Acid-Sensitive Cu2O@Cu-MOF Nano Sustained-Release Capsules with Superior Antifouling Behaviors

Marine biofouling is one of the technical bottlenecks restricting the development of the global marine economy. Among the commercial self-polishing antifouling coatings, cuprous oxide is an irreplaceable component because of its efficiency and broad-spectrum antibacterial activity. However, one of the biggest obstacles to achieving long-term antifouling is the "initial burst and final decay" of cuprous oxide in the coating. Here, we lock the copper ions by establishing an antifouling unit composed of Cu₂O (core) and Cu-based metal-organic framework (Cu-MOF, shell). Cu-MOF is densely grown in situ on the periphery of Cu₂O by acid proton etching. The shell structure of Cu-MOF can effectively improve the stability of the internal Cu₂O and thus achieve the stable and slow release of copper ions. Furthermore, Cu₂O@Cu-MOF nanocapsules can also achieve active defense by rapid and complete dissolution of Cu₂O@Cu-MOF at local acidic microenvironment (pH ≤ 5) where the adhesion of fouling organisms occurs. Super-resolution fluorescence microscopy is used to explain the sterilization mechanism. Relying on the water- and acid-sensitive properties of Cu-MOF shell, the stable, controlled and efficient release of copper ions has been achieved for the Cu₂O@Cu-MOF nanocapsules in the self-polishing antifouling coatings. Thus, these controlled-release nanocapsules make long-term antifouling promising.

Mechanistic revealing of reproductive behavior impairment in male guppy (Poecilia reticulata) induced by environmentally realistic 2,2'-dithiobis-pyridine exposure

Although (PS)₂, the primary degradation product of emerging antifouling biocides metal pyrithiones (MePTs), can disrupt the reproductive behavior of fish at an environmentally relevant ng/L level, the underlying mechanism is still largely unknown. This study exposed sexually mature male guppy (Poecilia reticulata) to 20, 200, and 2000 ng/L (PS)₂ to explore the compromised effect of (PS)₂ on reproductive behavior through a realistic competing scenario. The results showed that (PS)₂ suppressed male guppies' sexual interest to stimulus females, reduced their competitive behavior frequencies toward rival males, and decreased their mating time and frequency. (PS)₂ exposure did not affect male guppies' secondary sexual characteristics or induce estrogenic activity. Whole-brain transcriptome sequencing identified 1070 differentially expressed genes (DEGs) with 872 up-regulated genes, which were functionally enriched into Gene Ontology terms pertaining to extracellular matrix (ECM) and extracellular region. KEGG enrichment for the DEGs uncovered that the activations of ECM-receptor interaction and focal adhesion pathways could be the underlying molecular mechanism implicated in the (PS)₂ induced reproductive behavior impairment. This work would deliver a substantial contribution to the understanding of the ecological safety of MePTs biocides.

Antibacterial surfaces: Strategies and applications

Antibacterial surfaces are surfaces that can resist bacteria, relying on the nature of the material itself. It is significant for safe food and water, human health, and industrial equipment. Biofilm is the main form of bacterial contamination on the material surface. Preventing the formation of biofilm is an efficient way to develop antibacterial surfaces. The strategy for constructing the antibacterial surface is divided into bacteria repelling and bacteria killing based on the formation of the biofilm. Material surface wettability, adhesion, and steric hindrance determine bacteria repelling performance. Bacteria should be killed by surface chemistry or physical structures when they are attached to a material surface irreversibly. Killing approaches are usually in the light of the cell membrane of bacteria. This review summarizes the fabrication methods and applications of antibacterial surfaces from the view of the treatment of the material surfaces. We also present several crucial points for developing long-term stability, no drug resistance, broad-spectrum, and even programable antibacterial surfaces.

Antifouling Activity of Halogenated Compounds Derived from the Red Alga Sphaerococcus coronopifolius: Potential for the Development of Environmentally Friendly Solutions

Nowadays, biofouling is responsible for enormous economic losses in the maritime sector, and its treatment with conventional antifouling paints is causing significant problems to the environment. Biomimetism and green chemistry approaches are very promising research strategies for the discovery of new antifouling compounds. This study focused on the red alga Sphaerococcus coronopifolius, which is known as a producer of bioactive secondary metabolites. Fifteen compounds, including bromosphaerol (1), were tested against key marine biofoulers (five marine bacteria and three microalgae) and two enzymes associated with the adhesion process in macroalgae and invertebrates. Each metabolite presented antifouling activity against at least one organism/enzyme. This investigation also revealed that two compounds, sphaerococcinol A (4) and 14R-hydroxy-13,14-dihydro-sphaerococcinol A (5), were the most potent compounds without toxicity towards oyster larvae used as non-target organisms. These compounds are of high potential as they are active towards key biofoulers and could be produced by a cultivable alga, a fact that is important from the green chemistry point of view.

Highly Efficient Self-Repairing Slippery Liquid-Infused Surface with Promising Anti-Icing and Anti-Fouling Performance

Smart slippery liquid-infused porous surfaces (SLIPSs) have aroused remarkable attention owing to tremendous application foreground in biomedical instruments and industry. However, challenges still remain in fabricating durable SLIPSs. In this work, a fast and highly efficient self-repairing slippery surface (SPU-60M) was fabricated based on a polyurethane membrane and silicone oil. By introducing a great quantity of reversible disulfide bonds into the polymer backbone and hydrogen bonds in the polymer interchain, this SLIPS material could be quickly repaired in 15 min with 97.8% healing efficiency. Moreover, the self-healing efficiency could be maintained at 42.75% after the 10th cutting-healing cycle. Notably, SPU-60M showed excellent self-repairing ability not only in an ambient environment but also in an underwater environment and at ultralow temperatures. Besides, the icing delay time (DT) of SPU-60M could be prolonged to 1182 s at -15 °C, and the ice adhesion strength was only 10.33 kPa at -30 °C. In addition, SPU-60M had excellent anti-fouling performance with BSA adsorption of 2.41 μg/cm² and Escherichia coli CFU counts of 41 × 10⁴. These findings provide a facile way to design highly efficient self-repairing SLIPSs with multifunctionality.

Engineered topographies and hydrodynamics in relation to biofouling control-a review

Biofouling, the unwanted growth of microorganisms on submerged surfaces, has appeared as a significant impediment for underwater structures, water vessels, and medical devices. For fixing the biofouling issue, modification of the submerged surface is being experimented as a non-toxic approach worldwide. This technique necessitated altering the surface topography and roughness and developing a surface with a nano- to micro-structured pattern. The main objective of this study is to review the recent advancements in surface modification and hydrodynamic analysis concerning biofouling control. This study described the occurrence of the biofouling process, techniques suitable for biofouling control, and current state of research advancements comprehensively. Different biofilms under various hydrodynamic conditions have also been outlined in this study. Scenarios of biomimetic surfaces and underwater super-hydrophobicity, locomotion of microorganisms, nano- and micro-hydrodynamics on various surfaces around microorganisms, and material stiffness were explained thoroughly. The review also documented the approaches to inhibit the initial settlement of microorganisms and prolong the subsequent biofilm formation process for patterned surfaces. Though it is well documented that biofouling can be controlled to various degrees with different nano- and micro-structured patterned surfaces, the understanding of the underlying mechanism is still imprecise. Therefore, this review strived to present the possibilities of implementing the patterned surfaces as a physical deterrent against the settlement of fouling organisms and developing an active microfluidic environment to inhibit the initial bacterial settlement process. In general, microtopography equivalent to that of bacterial cells influences attachment via hydrodynamics, topography-induced cell placement, and air-entrapment, whereas nanotopography influences physicochemical forces through macromolecular conditioning.

Proteomic study of Desulfovibrio ferrophilus IS5 reveals overexpressed extracellular multi-heme cytochrome associated with severe microbiologically influenced corrosion

Microbiologically influenced corrosion (MIC) is recognized as a considerable threat to carbon steel asset integrity in the oil and gas industry. There is an immediate need for reliable and broadly applicable methods for detection and monitoring of MIC. Proteins associated with microbial metabolisms involved in MIC could serve as useful biomarkers for MIC diagnosis and monitoring. A proteomic study was conducted using a lithotrophically-grown bacterium Desulfovibrio ferrophilus strain IS5, which is known to cause severe MIC in seawater environments. Unique proteins, which are differentially and uniquely expressed during severe microbial corrosion by strain IS5, were identified. This includes the detection of a multi-heme cytochrome protein possibly involved in extracellular electron transfer in the presence of the carbon steel. Thus, we conclude that this newly identified protein associated closely with severe MIC could be used to generate easy-to-implement immunoassays for reliable detection of microbiological corrosion in the field.

Morphology modulation and performance optimization of nanopetal-based Ag-modified Bi2O2CO3 as an inactivating photocatalytic material

The use of photocatalytic technology to kill bacteria on marine vessel surface coatings has been paid more attention by research scholars. In this paper, petal-like microspheres with Ag nanoparticles were prepared by a simple one-step process combining the hydrothermal method and photodeposition. The 0.7% Ag/Bi₂O₂CO₃ composite photocatalyst exhibited the highest photocatalytic efficiency for bacterial removal under visible light irradiation and had the highest photogenerated carrier separation efficiency, and the sterilization rate was doubled compared with that of pure Bi₂O₂CO₃, reaching 95%. Using X-ray photoelectron spectroscopy, scanning electron microscopy and transmission electron microscopy, the existence of Ag nanoparticles was confirmed, and their size was approximately 10 nm. The surface plasmon resonance (SPR) effect of Ag nanoparticles was investigated by ultraviolet-visible diffuse reflectance spectroscopy (DRS). It was shown that the surface plasmon resonance effect of Ag improved the spectral utilization of the Ag/Bi₂O₂CO₃ composite photocatalyst and enhanced the stability of the catalyst. This caused the Ag/Bi₂O₂CO₃ composite photocatalyst to have superior photocatalytic activity to pure Bi₂O₂CO₃. The results of electrochemical impedance characterization and transient photocurrent response show that 0.7% Ag/Bi₂O₂CO₃ has a high efficiency of photogenerated carrier separation. By the free radical capture test, hydroxyl radicals were the primary active substance, and Ag⁺ improved the photocatalytic sterilization activity.

Environmentally Friendly Anticorrosive Polymeric Coatings

This paper provides a synthetic and comprehensive overview on environmentally friendly anticorrosive polymeric coatings. Firstly, the economic and environmental impact of corrosion is presented to highlight the need of anticorrosive polymeric coatings as a flexible and effective solution to protect a metal. Secondly, the implementation of regulations together with the consumer awareness for environmental considerations and protection of health are the driving force for a progressive but significant change in the sector. Therefore, within the protective organic coatings market, this article provides a review of the most recent developments in environmentally friendly solutions, including bio-based and water-borne epoxy, hyperbranched polyester for low- volatile organic compounds (VOC) coatings, waterborne polyurethane and non-isocyanate polyurethanes (NIPUs), and graphene or bio-based fillers for acrylics. Moreover, this paper outlines new trends such as smart additives, bio-based corrosion inhibitors, and functional antibiocorrosive coatings as superhydrophobics. Finally, industrially relevant applications of environmentally friendly anticorrosive polymeric coatings including solutions for marine and off-shore industries are summarized.

Efficiency of Gemini surfactant containing semi-rigid spacer as microbial corrosion inhibitor for carbon steel in simulated seawater

SRB is one of the main bacteria causing marine microbial corrosion. In order to reduce the loss of microbial corrosion, a Gemini surfactant (12-B-12) containing semi-rigid spacer was used to investigate the anti-bacterial and anti-corrosion performances of carbon steel in simulated seawater by weight-loss test, electrochemical method and surface morphology analysis. The results showed that the inhibition efficiency of 0.01 mM 12-B-12 was as high as 98.3% after 30 days of incubation in simulated seawater with SRB, and the planktonic and sessile SRB on the carbon steel surface can be reduced to undetectable level. Quantum chemical calculation and molecular dynamics simulation were used to study the structure-activity relationship.

Microstructure and Properties of Poly(ethylene glycol)-Segmented Polyurethane Antifouling Coatings after Immersion in Seawater

Polyurethane has a microphase separation structure, while polyethylene glycol (PEG) can form a hydrated layer to resist protein adsorption. In this paper, PEG was introduced to polyurethane to improve the antifouling properties of the polyurethane, providing a new method and idea for the preparation of new antifouling polyurethane materials. The mechanical properties, hydrophilicity, swelling degree, microphase separation and antifouling performance of the coatings were evaluated. The response characteristics of the polyurethane coatings in a seawater environment were studied, and the performance changes of coatings in seawater were tested. The results showed that the crystallized PEG soft segments increased, promoting microphase separation. The stress at 100% and the elasticity modulus of the polyurethane material also markedly increased, in addition to increases in the swelling degree in seawater, the water contact angle decreased. A total of 25% of PEG incorporated into a soft segment can markedly improve the antibacterial properties of the coatings, but adding more PEG has little significant effect. After immersion in seawater, the coatings became softer and more elastic. This is because water molecules formed hydrogen bonding with the amino NH, which resulted in a weakening effect being exerted on the carbonyl C=O hydrogen bonding and ether oxygen group crystallization.

Effect of different disinfection treatments on the adhesion and separation of biofilm on stainless steel surface

Attachment and separation of sulfate-reducing bacteria (SRB) biofilm on stainless steel (SS) in simulated cooling water with and without different sterilization treatments was investigated by calculation of surface energy, theoretical work of adhesion and analysis of Scanning Electron Microscope/Energy Dispersive Spectrometer. Two types of biocides, glutaraldehyde and Polyhexamethylene guanidine (PHMG), and electromagnetic treatment were used in this paper. The results show that PHMG had the best bactericidal performance, followed by glutaraldehyde, and electromagnetic treatment was the lowest one. The theoretical work of adhesion was used to quantitatively evaluate the adhesion of biofilm on the surface of the metal. Theoretical work of adhesion between biofilm and SS in simulated cooling water increased with time. The theoretical adhesion work and adhesive capacity of biofilm to SS surface increased after treating with glutaraldehyde while decreasing after treating with PHMG and electromagnetic field. As the theoretical adhesion work decreased, the biofilm was gradually removed from the stainless steel surface. On the contrary, the biofilm adhered more firmly. The results of SEM were also consistent with the calculation results of theoretical adhesion work. The results obtained indicated that electromagnetic treatment had the lowest effect in sterilization but the best in biofilm separation.

Antifouling Activity of Meroterpenes Isolated from the Ascidian Aplidium aff. densum

The settlement and growth of fouling organisms on man-made surfaces can be prevented by the application of antifouling paints containing active compounds (biocides, heavy metals), most of which are toxic to non-target organisms. As part of our research program in chemical ecology and blue biotechnology, we are conducting studies to investigate the natural defence mechanisms of marine organisms that are free from epibionts, with the aim of isolating molecules involved in surface defence that could be good candidates as antifouling agents. Ascidians were selected for our investigation because previous studies have shown that they contain abundant and diverse secondary metabolites, which play a defensive role and have been applied to drug discovery. It is therefore relevant to study the role of such secondary metabolites in surface protection. In this study, 5 meroterpenoids (cordiachromene A, didehydroconicol, epiconicol, methoxyconidiol, conidione) from Aplidium aff. densum (ascidian) were investigated as potential antifoulants towards the inhibition of bacterial growth and settlement inhibition of barnacles. Cardiochromene A (IC₅₀ barnacle settlement = 6.04 μg/mL; MIC Gram positive = 125 μg/mL; MIC Gram negative = 32 μg/mL) and epiconicol (IC₅₀ barnacle settlement = 8.05 μg/mL; MIC Bacillus = 63 μg/mL; MIC other strains = 32 μg/mL) were the most promising compounds among those tested in this study.

Raposo MM. Optical Fiber Sensors for Biocide Monitoring: Examples, Transduction Materials, and Prospects

Antifouling biocides are toxic to the marine environment impacting negatively on the aquatic ecosystems. These biocides, namely, tributyltin (TBT) and Cu(I) compounds, are used to avoid biofouling; however, their toxicity turns TBT and Cu(I) monitoring an important health issue. Current monitoring methods are expensive and time-consuming. This review provides an overview of the actual state of the art of antifouling paints' biocides, including their impact and toxicity, as well as the reported methods for TBT and Cu(I) detection over the past decade. The principles of optical fiber sensors (OFS) applications, with focus on environmental applications, and the use of organic chemosensors in this type of sensors are debated. The multiplexing ability of OFS and their application on aquatic environments are also discussed.

Copper Surfaces in Biofilm Control

Biofilms are structures comprising microorganisms associated to surfaces and enclosed by an extracellular polymeric matrix produced by the colonizer cells. These structures protect microorganisms from adverse environmental conditions. Biofilms are typically associated with several negative impacts for health and industries and no effective strategy for their complete control/eradication has been identified so far. The antimicrobial properties of copper are well recognized among the scientific community, which increased their interest for the use of these materials in different applications. In this review the use of different copper materials (copper, copper alloys, nanoparticles and copper-based coatings) in medical settings, industrial equipment and plumbing systems will be discussed considering their potential to prevent and control biofilm formation. Particular attention is given to the mode of action of copper materials. The putative impact of copper materials in the health and/or products quality is reviewed taking into account their main use and the possible effects on the spread of antimicrobial resistance.

Hybrid Sol-gel Coatings for Corrosion Mitigation: A Critical Review

The corrosion process is a major source of metallic material degradation, particularly in aggressive environments, such as marine ones. Corrosion progression affects the service life of a given metallic structure, which may end in structural failure, leakage, product loss and environmental pollution linked to large financial costs. According to NACE, the annual cost of corrosion worldwide was estimated, in 2016, to be around 3%-4% of the world's gross domestic product. Therefore, the use of methodologies for corrosion mitigation are extremely important. The approaches used can be passive or active. A passive approach is preventive and may be achieved by emplacing a barrier layer, such as a coating that hinders the contact of the metallic substrate with the aggressive environment. An active approach is generally employed when the corrosion is set in. That seeks to reduce the corrosion rate when the protective barrier is already damaged and the aggressive species (i.e., corrosive agents) are in contact with the metallic substrate. In this case, this is more a remediation methodology than a preventive action, such as the use of coatings. The sol-gel synthesis process, over the past few decades, gained remarkable importance in diverse areas of application. Sol-gel allows the combination of inorganic and organic materials in a single-phase and has led to the development of organic-inorganic hybrid (OIH) coatings for several applications, including for corrosion mitigation. This manuscript succinctly reviews the fundamentals of sol-gel concepts and the parameters that influence the processing techniques. The state-of-the-art of the OIH sol-gel coatings reported in the last few years for corrosion protection, are also assessed. Lastly, a brief perspective on the limitations, standing challenges and future perspectives of the field are critically discussed.

The effect of magnetic field pretreatment on the corrosion behavior of carbon steel in static seawater

The corrosion behavior of carbon steel pretreated with a magnetic field before electrochemical testing was investigated in static seawater using electrochemical methods in the absence of an external magnetic field. The shift in corrosion potential was more significant with increasing pretreating magnetic field strength, and the corrosion current density also decreased. This implies that the carbon steel corrosion was inhibited. The main reason for this inhibition is that the magnetic field affects the formation of intermediate products on the carbon steel surface by both charge transfer and magnetic ion adsorption. The magnetic field pretreatment will likely offer a new approach for marine anti-corrosion technology.

Effect of magnetic field pretreatment on carbon steel corrosion behavior in seawater was investigated by electrochemical methods. This method can inhibit the corrosion behavior and is expected to provide a new way for marine anti-corrosion.

Progress in biomimetic leverages for marine antifouling using nanocomposite coatings

Because of the environmental and economic casualties of biofouling on maritime navigation, modern studies have been devoted toward formulating advanced nanoscale composites in the controlled development of effective marine antifouling self-cleaning surfaces.

Bioactive Aliphatic Sulfates from Marine Invertebrates

The occurrence of sulfated steroids and phenolics in marine organisms is quite widespread, being typically reported from Echinoderms. In contrast, alkane and alkene aliphatic sulfates are considerably rarer with examples being reported from a diverse array of organisms including echinoderms, sponges and ascidians. While no ecological roles for these metabolites have been proposed, they do exhibit a diverse array of biological activities including thrombin inhibition; the ability to induce metamorphosis in larvae; antiproliferative, antibacterial and antifungal properties; and metalloproteinase inhibition. Of particular interest and an avenue for future development is the finding of antifouling properties with low or nontoxic effects to the environment. This review focuses on alkyl sulfates and related sulfamates, their structures and biological activities. Spectroscopic and spectrometric techniques that can be used to recognize the presence of sulfate groups are also discussed, data for which will enhance the ability of researchers to recognize this class of chemically- and biologically-interesting marine natural products.