Direct electrochemistry of alcohol oxidase using multiwalled carbon nanotube as electroactive matrix for biosensor application

Self-powered wearable biosensor based on stencil-printed carbon nanotube electrodes for ethanol detection in sweat

Herein we introduce a novel water-based graphite ink modified with multiwalled carbon nanotubes, designed for the development of the first wearable self-powered biosensor enabling alcohol abuse detection through sweat analysis. The stencil-printed graphite (SPG) electrodes, printed onto a flexible substrate, were modified by casting multiwalled carbon nanotubes (MWCNTs), electrodepositing polymethylene blue (pMB) at the anode to serve as a catalyst for nicotinamide adenine dinucleotide (NADH) oxidation, and hemin at the cathode as a selective catalyst for H2O2 reduction. Notably, alcohol dehydrogenase (ADH) was additionally physisorbed onto the anodic electrode, and alcohol oxidase (AOx) onto the cathodic electrode. The self-powered biosensor was assembled using the ADH/pMB-MWCNTs/SPG||AOx/Hemin-MWCNTs/SPG configuration, enabling the detection of ethanol as an analytical target, both at the anodic and cathodic electrodes. Its performance was assessed by measuring polarization curves with gradually increasing ethanol concentrations ranging from 0 to 50 mM. The biosensor demonstrated a linear detection range from 0.01 to 0.3 mM, with a detection limit (LOD) of 3 ± 1 µM and a sensitivity of 64 ± 2 μW mM-1, with a correlation coefficient of 0.98 (RSD 8.1%, n = 10 electrode pairs). It exhibited robust operational stability (over 2800 s with continuous ethanol turnover) and excellent storage stability (approximately 93% of initial signal retained after 90 days). Finally, the biosensor array was integrated into a wristband and successfully evaluated for continuous alcohol abuse monitoring. This proposed system displays promising attributes for use as a flexible and wearable biosensor employing biocompatible water-based inks, offering potential applications in forensic contexts.

Design and Construction of Enzyme-Based Electrochemical Gas Sensors

The demand for the ubiquitous detection of gases in complex environments is driving the design of highly specific gas sensors for the development of the Internet of Things, such as indoor air quality testing, human exhaled disease detection, monitoring gas emissions, etc. The interaction between analytes and bioreceptors can described as a "lock-and-key", in which the specific catalysis between enzymes and gas molecules provides a new paradigm for the construction of high-sensitivity and -specificity gas sensors. The electrochemical method has been widely used in gas detection and in the design and construction of enzyme-based electrochemical gas sensors, in which the specificity of an enzyme to a substrate is determined by a specific functional domain or recognition interface, which is the active site of the enzyme that can specifically catalyze the gas reaction, and the electrode-solution interface, where the chemical reaction occurs, respectively. As a result, the engineering design of the enzyme electrode interface is crucial in the process of designing and constructing enzyme-based electrochemical gas sensors. In this review, we summarize the design of enzyme-based electrochemical gas sensors. We particularly focus on the main concepts of enzyme electrodes and the selection and design of materials, as well as the immobilization of enzymes and construction methods. Furthermore, we discuss the fundamental factors that affect electron transfer at the enzyme electrode interface for electrochemical gas sensors and the challenges and opportunities related to the design and construction of these sensors.

Adoption of analytical technologies for verification of authenticity of halal foods - a review

Halal authentication has become essential in the food industry to ensure food is free from any prohibited ingredients according to Islamic law. Diversification of food origin and adulteration issues have raised concerns among Muslim consumers. Therefore, verification of food constituents and their quality is paramount. From conventional methods based on physical and chemical properties, various diagnostic methods have emerged relying on protein or DNA measurements. Protein-based methods that have been used in halal detection including electrophoresis, chromatographic-based methods, molecular spectroscopy and immunoassays. Polymerase chain reaction (PCR) and loop-mediated isothermal amplification (LAMP) are DNA-based techniques that possess better accuracy and sensitivity. Biosensors are miniatured devices that operate by converting biochemical signals into a measurable quantity. CRISPR-Cas is one of the latest novel emerging nucleic acid detection tools in halal food analysis as well as quantification of stable isotopes method for identification of animal species. Within this context, this review provides an overview of the various techniques in halal detection along with their advantages and limitations. The future trend and growth of detection technologies are also discussed in this review.

Reusable alcohol oxidase-nPtCu/alginate beads for highly sensitive ethanol assay in beverages

Nanozymes (NZs) are nanoparticles that mimic the catalytic properties of natural enzymes. The present work aimed to obtain effective peroxidase mimetics (PO-like NZs), to characterize their morphological properties, estimate the kinetic parameters of NZs and evaluate the prospects of their application in analysis of ethanol. Herein, we have proposed a convenient spectrophotometric method for ethanol assay using reusable alginate beads enriched with alcohol oxidase (AO) and nanoparticles of PtCu (nPtCu) as PO-like NZs, and 3,3',5,5'-tetramethylbenzidine (TMB) as a chromogen. The linear range for the proposed nPtCu-AO/alginate beads/TMB-based method is from 0.01 mM to 0.15 mM with a limit of detection of 3.3 μM ethanol. The method is used for the quantitative determination of ethanol in alcoholic beverages. The obtained results proved to be in a good correlation with the enzymatic reference method. These results highlight the potential of the nPtCu with PO-like activity in bioanalytical applications. The proposed method, being sensitive, economical and suitable for routine and micro-volume formats, can be used in clinical diagnostics for the detection of ethanol.

Recent advances in halal food authentication: Challenges and strategies

Increasing public awareness of food quality and safety has prompted a rapid increase in food authentication of halal food, which covers the production method, technical processing, identification of undeclared components, and species substitution in halal food products. This urges for extensive research into analytical methods to obtain accurate and reliable results for monitoring and controlling the authenticity of halal food. Nonetheless, authentication of halal food is often challenging because of the complex nature of food and the increasing number of food adulterants that cause detection difficulties. This review provides a comprehensive and impartial overview of recent studies on the analytical techniques used in the analysis of halal food authenticity (from 1980 to the present, but there has been no significant trend in the choice of techniques for authentication of halal food during this period). Additionally, this review highlights the classification of different methodologies based on validity measures that provide valuable information for future developments in advanced technology. In addition, methodological developments, and novel emerging techniques as well as their implementations have been explored in the evaluation of halal food authentication. This includes food categories that require halal authentication, illustrating the advantages and disadvantages as well as shortcomings during the use of all approaches in the halal food industry.

Multiwalled carbon nanotubes bound beta-galactosidase: It's activity, stability and reusability

Carbon nanotubes (CNTs) based biosensors are recognized to be a next generation building block for ultrasensitive and fast biosensing systems. This article starting with a brief history on CNTs provides an overview on the recent expansion of research in the field of CNT-based biosensors. This is followed by the discussion on structure and properties related to CNTs. Furthermore, the basic and some newly developed synthetic methods of CNTs are summarized. In this chapter, we used polyaniline cobalt multiwalled CNTs to immobilize β-galactosidase, by adopting both noncovalent and covalent strategies. Herein, the methodologies of both techniques have been discussed in detail. The η (effectiveness factor) values for nanocomposite bound β-galactosidase by physical adsorption and covalent method were calculated to be 0.93 and 0.97, respectively. The covalently bound β-galactosidase retained 92% activity even after its 10th successive reuse as compared to the adsorbed enzyme which exhibited only 74% of its initial activity. CNT armored enzymes demonstrated remarkably high catalytic stability at both sides of temperature and pH-optima along with easy recovery from the reaction medium which can be utilized in various biotechnological applications. Lastly, the scientific and technological challenges in the field are discussed at the end of this chapter.

Hollow Prussian Blue nanocubes as peroxidase mimetic and enzyme carriers for colorimetric determination of ethanol

The peroxidase-like activity of hollow Prussian Blue nanocubes (hPBNCs) is used, in combination with the enzyme alcohol oxidase (AOx), in a colorimetric ethanol assay. Different from other nanozymes, the large cavity structure of the hPBNCs provides a larger surface and more binding sites for AOx to be bound on their surface or in the pores. This extremely enhances the sensitivity of the assay system. In the presence of ethanol, AOx is capable of catalyzing the oxidation of alcohols to aldehydes, accompanied by the generation of hydrogen peroxide (H₂O₂). The hPBNCs act as peroxidase mimics and then can catalyze the oxidation of 3,3'5,5'-tetramethylbenzidine (TMB) by H₂O₂, resulting in a color change of the solution from colorless to blue with a strong absorption at 652 nm. The lower detection limit for ethanol is 1.41 μg∙mL^-1. Due to the high catalytic activity of hPBNCs in weakly acidic and neutral solutions, the system was successfully applied to the determination of ethanol in mice blood. This is critically important for studying the alcohol consumption and monitoring the ethanol toxicokinetics. Graphical abstract Schematic representation of hollow Prussian Blue nanocubes (hPBNCs) used as both a peroxidase mimetic and as a carrier for alcohol oxidase. Utilizing hPBNCs along with the ethanol conversion enzyme, a sensitive colorimetric assay for ethanol was developed and applied to blood samples with satisfactory results.

Advances in the design of nanomaterial-based electrochemical affinity and enzymatic biosensors for metabolic biomarkers: A review

This review (with 340 refs) focuses on methods for specific and sensitive detection of metabolites for diagnostic purposes, with particular emphasis on electrochemical nanomaterial-based sensors. It also covers novel candidate metabolites as potential biomarkers for diseases such as neurodegenerative diseases, autism spectrum disorder and hepatitis. Following an introduction into the field of metabolic biomarkers, a first major section classifies electrochemical biosensors according to the bioreceptor type (enzymatic, immuno, apta and peptide based sensors). A next section covers applications of nanomaterials in electrochemical biosensing (with subsections on the classification of nanomaterials, electrochemical approaches for signal generation and amplification using nanomaterials, and on nanomaterials as tags). A next large sections treats candidate metabolic biomarkers for diagnosis of diseases (in the context with metabolomics), with subsections on biomarkers for neurodegenerative diseases, autism spectrum disorder and hepatitis. The Conclusion addresses current challenges and future perspectives. Graphical abstract This review focuses on the recent developments in electrochemical biosensors based on the use of nanomaterials for the detection of metabolic biomarkers. It covers the critical metabolites for some diseases such as neurodegenerative diseases, autism spectrum disorder and hepatitis.

Advances in developing rapid, reliable and portable detection systems for alcohol

Development of portable, reliable, sensitive, simple, and inexpensive detection system for alcohol has been an instinctive demand not only in traditional brewing, pharmaceutical, food and clinical industries but also in rapidly growing alcohol based fuel industries. Highly sensitive, selective, and reliable alcohol detections are currently amenable typically through the sophisticated instrument based analyses confined mostly to the state-of-art analytical laboratory facilities. With the growing demand of rapid and reliable alcohol detection systems, an all-round attempt has been made over the past decade encompassing various disciplines from basic and engineering sciences. Of late, the research for developing small-scale portable alcohol detection system has been accelerated with the advent of emerging miniaturization techniques, advanced materials and sensing platforms such as lab-on-chip, lab-on-CD, lab-on-paper etc. With these new inter-disciplinary approaches along with the support from the parallel knowledge growth on rapid detection systems being pursued for various targets, the progress on translating the proof-of-concepts to commercially viable and environment friendly portable alcohol detection systems is gaining pace. Here, we summarize the progress made over the years on the alcohol detection systems, with a focus on recent advancement towards developing portable, simple and efficient alcohol sensors.

Effect of electrode surface properties on enhanced electron transfer activity in microbial fuel cells

The influence of electrode surface chemistry over biofilm growth was evaluated for photo-bioelectrocatalytic fuel cell. A consortium of photosynthetic bacteria was grown onto different electrodes designed with polyethylenimine (PEI) and multiwall carbon nanotubes as hydrophilic and hydrophobic modifier, respectively. The designed electrodes were loaded with 0.08, 0.17, and 0.33 μg/cm² of PEI to change the hydrophilicity. However, 0.56, 0.72, and 0.83 mg/cm² of multiwall carbon nanotubes were used to alter the hydrophobicity of the electrodes. The surface chemistry of electrode and bio-interaction was evaluated as a function of contact angle and biofilm formation. The results were compared with those obtained with a carbon paper electrode. The contact angle on the untreated electrode (carbon paper) was 118°, whereas for hydrophobic and hydrophilic electrodes, the maximum and minimum contact angles were 170° and 0°, respectively. Interestingly, the maximum biofilm growth (0.2275 g, wet basis) was observed on highly hydrophobic surface; however, the maximum electrochemical performance (246 mV) was shown by the most hydrophilic electrode surface. PEI-based electrode with good biofilm formation showed comparatively higher electrogenic activity.

New CNT/poly(brilliant green) and CNT/poly(3,4-ethylenedioxythiophene) based electrochemical enzyme biosensors

A combination of the electroactive polymer poly(brilliant green) (PBG) or conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) with carbon nanotubes to obtain CNT/PBG and CNT/PEDOT modified carbon film electrodes (CFE) has been investigated as a new biosensor platform, incorporating the enzymes glucose oxidase (GOx) as test enzyme, alcohol oxidase (AlcOx) or alcohol dehydrogenase (AlcDH). The sensing parameters were optimized for all biosensors based on CNT/PBG/CFE, CNT/PEDOT/CFE platforms. Under optimized conditions, both GOx biosensors exhibited very similar sensitivities, while in the case of AlcOx and AlcDH biosensors, AlcOx/CNT/PBG/CFE was found to give a higher sensitivity and lower detection limit. The influence of dissolved O2 on oxidase-biosensor performance was investigated and was shown to be different for each enzyme. Comparisons were made with similar reported biosensors, showing the advantages of the new biosensors, and excellent selectivity against potential interferents was successfully demonstrated. Finally, alcohol biosensors were successfully used for the determination of ethanol in alcoholic beverages.

Tuning Structural Changes in Glucose Oxidase for Enzyme Fuel Cell Applications

Stabilization and electrical contacting of redox enzymes with electrodes are fundamental requirements for bioelectronics devices, including biosensors and enzyme fuel cells (EFCs). In this study, we show increased glucose oxidase (GOx) stability by immobilization with Nafion. The immobilization process affected GOx conformation but was not detrimental to its activity, which was maintained for more than 120 days. The GOx/Nafion system was interfaced to a carbon cloth electrode and assembled in a prototypal EFC fed with glucose. Polarization and power density curves demonstrated that GOx/Nafion system was able to generate power, exploiting a Nafion-assisted electron transfer process to the electrode. Our findings are consistent with the onset of pH-dependent conformational equilibrium for the enzyme secondary structure and its active site. Significantly, the protective effect exerted by Nafion on the enzyme structure may be tuned by varying parameters such as the pH to fabricate durable EFCs with good electrocatalytic performance.

Recent advances on developing 3rd generation enzyme electrode for biosensor applications

The electrochemical biosensor with enzyme as biorecognition element is traditionally pursued as an attractive research topic owing to their high commercial perspective in healthcare and environmental sectors. The research interest on the subject is sharply increased since the beginning of 21st century primarily, due to the concomitant increase in knowledge in the field of material science. The remarkable effects of many advance materials such as, conductive polymers and nanomaterials, were acknowledged in the developing efficient 3rd generation enzyme bioelectrodes which offer superior selectivity, sensitivity, reagent less detection, and label free fabrication of biosensors. The present review article compiles the major knowledge surfaced on the subject since its inception incorporating the key review and experimental papers published during the last decade which extensively cover the development on the redox enzyme based 3rd generation electrochemical biosensors. The tenet involved in the function of these direct electrochemistry based enzyme electrodes, their characterizations and various strategies reported so far for their development such as, nanofabrication, polymer based and reconstitution approaches are elucidated. In addition, the possible challenges and the future prospects in the development of efficient biosensors following this direct electrochemistry based principle are discussed. A comparative account on the design strategies and critical performance factors involved in the 3rd generation biosensors among some selected prominent works published on the subject during last decade have also been included in a tabular form for ready reference to the readers.

Recent trends in carbon nanomaterial-based electrochemical sensors for biomolecules: A review

Carbon nanomaterials are advantageous for electrochemical sensors because they increase the electroactive surface area, enhance electron transfer, and promote adsorption of molecules. Carbon nanotubes (CNTs) have been incorporated into electrochemical sensors for biomolecules and strategies have included the traditional dip coating and drop casting methods, direct growth of CNTs on electrodes and the use of CNT fibers and yarns made exclusively of CNTs. Recent research has also focused on utilizing many new types of carbon nanomaterials beyond CNTs. Forms of graphene are now increasingly popular for sensors including reduced graphene oxide, carbon nanohorns, graphene nanofoams, graphene nanorods, and graphene nanoflowers. In this review, we compare different carbon nanomaterial strategies for creating electrochemical sensors for biomolecules. Analytes covered include neurotransmitters and neurochemicals, such as dopamine, ascorbic acid, and serotonin; hydrogen peroxide; proteins, such as biomarkers; and DNA. The review also addresses enzyme-based electrodes that are used to detect non-electroactive species such as glucose, alcohols, and proteins. Finally, we analyze some of the future directions for the field, pointing out gaps in fundamental understanding of electron transfer to carbon nanomaterials and the need for more practical implementation of sensors.

Alcohol oxidase protein mediated in-situ synthesized and stabilized gold nanoparticles for developing amperometric alcohol biosensor

A simple one step method for the alcohol oxidases (AOx) protein mediated synthesis of gold nano-particles (AuNPs) in alkaline (pH 8.5) condition with simultaneous stabilization of the nanoparticles on the AOx protein surface under native environment has been developed. The formation of the AOx conjugated AuNPs was confirmed by advanced analytical and spectroscopic techniques. The significant increase in zeta potential (ζ) value of -57mV for the synthesized AOx-AuNPs conjugate from the AOx (pI 4.5) protein (ζ, -30mV) implied good stability of the in-situ synthesized nano-conjugate. The AOx-AuNPs conjugate showed steady stability in alkaline (upto pH 8.5) and NaCl (up to 10(-1)M) solutions. The efficiency (Kcat/Km) of the AuNP conjugated AOx was increased by 18% from the free enzyme confirming the activating role of the surface stabilized AuNPs for the enzyme. The AuNPs-AOx conjugate was encapsulated with polyaniline (PANI) synthesized by oxidative polymerization of aniline using H2O2 generated in-situ from the AOx catalysed oxidation of alcohol. The PANI encapsulated AuNPs-AOx assembly was stabilized on a glassy carbon electrode (GCE) by chitosan-Nafion mixture and then utilized the fabricated bioelectrode for detection of alcohol amperometrically using H2O2 as redox indicator at +0.6V. The constructed biosensor showed high operational stability (6.3% loss after 25 measurements), wide linear detection range of 10µM-4.7mM (R(2)=0.9731), high sensitivity of 68.3±0.35µAmM(-1) and low detection limit of 7±0.027µM for ethanol. The fabricated bioelectrode was successfully used for the selective determination of alcohol in beverage samples.

A comparative study of graphene-hydrogel hybrid bionanocomposites for biosensing

Hydrogels have become increasingly popular as immobilization materials for cells, enzymes and proteins for biosensing applications. Enzymatic biosensors that utilize hydrogel as an encapsulant have shown improvements over other immobilization techniques such as cross linking and covalent bonding. However, to date there are no studies which directly compare multiple hydrogel-graphene nanocomposites using the same enzyme and test conditions. This study compares the performance of four different hydrogels used as protein encapsulants in a mediator-free biosensor based on graphene-nanometal-enzyme composites. Alcohol oxidase (AOx) was encapsulated in chitosan poly-N-isopropylacrylamide (PNIPAAM), silk fibroin or cellulose nanocrystals (CNC) hydrogels, and then spin coated onto a nanoplatinum-graphene modified electrode. The transduction mechanism for the biosensor was based on AOx-catalyzed oxidation of methanol to produce hydrogen peroxide. To isolate the effect(s) of stimulus response on biosensor behavior, all experiments were conducted at 25 °C and pH 7.10. Electroactive surface area (ESA), electrochemical impedance spectroscopy (EIS), sensitivity to methanol, response time, limit of detection, and shelf life were measured for each bionanocomposite. Chitosan and PNIPAAM had the highest sensitivity (0.46 ± 0.2 and 0.3 ± 0.1 μA mM(-1), respectively) and electroactive surface area (0.2 ± 0.06 and 0.2 ± 0.02 cm(2), respectively), as well as the fastest response time (4.3 ± 0.8 and 4.8 ± 1.1 s, respectively). Silk and CNC demonstrated lower sensitivity (0.09 ± 0.02 and 0.15 ± 0.03 μA mM(-1), respectively), lower electroactive surface area (0.12 ± 0.02 and 0.09 ± 0.03 cm(2), respectively), and longer response time (8.9 ± 2.1 and 6.3 ± 0.8 s, respectively). The high porosity of chitosan, PNIPAAM, and silk gels led to excellent transport, which was significantly better than CNC bionanocomposites. Electrochemical performance of CNC bionanocomposites were relatively poor, which may be linked to poor gel stability. The differences between the Chitosan/PNIPAAM group and the Silk/CNC group were statistically significant (p < 0.05) based on ANOVA. Each of these composites was within the range of other published devices in the literature, while some attributes were significantly improved (namely response time and shelf life). The main advantages of these hydrogel composites over other devices is that only one enzyme is required, all materials are non-toxic, the sensor does not require mediators/cofactors, and the shelf life and response time are significantly improved over other devices.

Novel l-lactic acid biosensors based on conducting polypyrrole-block copolymer nanoparticles

Novel polypyrrole-Pluronic F127 nanoparticles with conducting and biocompatibility properties were used to construct an l-lactic acid biosensor. This method proposes great potential for the detection and evaluation of meat quality.

Molecular characterization and expression of a novel alcohol oxidase from Aspergillus terreus MTCC6324

The alcohol oxidase (AOx) cDNA from Aspergillus terreus MTCC6324 with an open reading frame (ORF) of 2001 bp was constructed from n-hexadecane induced cells and expressed in Escherichia coli with a yield of ∼4.2 mg protein g⁻¹ wet cell. The deduced amino acid sequences of recombinant rAOx showed maximum structural homology with the chain B of aryl AOx from Pleurotus eryngii. A functionally active AOx was achieved by incubating the apo-AOx with flavin adenine dinucleotide (FAD) for ∼80 h at 16°C and pH 9.0. The isoelectric point and mass of the apo-AOx were found to be 6.5±0.1 and ∼74 kDa, respectively. Circular dichroism data of the rAOx confirmed its ordered structure. Docking studies with an ab-initio protein model demonstrated the presence of a conserved FAD binding domain with an active substrate binding site. The rAOx was specific for aryl alcohols and the order of its substrate preference was 4-methoxybenzyl alcohol >3-methoxybenzyl alcohol>3, 4-dimethoxybenzyl alcohol > benzyl alcohol. A significantly high aggregation to ∼1000 nm (diameter) and catalytic efficiency (k_cat/K_m) of 7829.5 min⁻¹ mM⁻¹ for 4-methoxybenzyl alcohol was also demonstrated for rAOx. The results infer the novelty of the AOx and its potential biocatalytic application.

Biosensors in forensic analysis. A review

Forensic analysis is an important branch of modern Analytical Chemistry with many legal and socially relevant implications. Biosensors can play an important role as efficient tools in this field considering their well known advantages of sensitivity, selectivity, easy functioning, affordability and capability of miniaturization and automation. This article reviews the latest advances in the use of biosensors for forensic analysis. The different methodologies for the transduction of the produced biological events are considered and the applications to forensic toxicological analysis, classified by the nature of the target analytes, as well as those related with chemical and biological weapons critically commented. The article provides several Tables where the more relevant analytical characteristics of the selected reported methods are gathered.

One-step fabrication of integrated disposable biosensor based on ADH/NAD+/meldola's blue/graphitized mesoporous carbons/chitosan nanobiocomposite for ethanol detection

A novel strategy to simplify the dehydrogenase-based electrochemical biosensor fabrication through one-step drop-coating nanobiocomposite on a screen printed electrode (SPE) was developed. The nanobiocomposite was prepared by successively adding graphitized mesoporous carbons (GMCs), meldola's blue (MDB), alcohol dehydrogenase (ADH) and cofactor nicotinamide adenine dinucleotide (NAD(+)) in chitosan (CS) solution. MDB/GMCs/CS film was prepared. Cyclic voltammetry measurements demonstrated that MDB was strongly adsorbed on GMCs. After optimizing the concentration of MDB and the working potential, the MDB/GMCs/CS film presented a fast amperometric response (5s), excellent sensitivity (10.36 nA μM(-1)), wide linear range (10-410 μM) toward NADH and without any other interference signals (such as AA, UA, DA, H2O2 and metal ions). Furthermore, concentrations of ADH and NAD(+) in nanobiocomposite and the detection conditions (temperature and pH) were also optimized. The constructed disposable ethanol biosensor showed an excellent linear response ranged from 0.5 to 15 mM with high sensitivity (67.28 nA mM(-1)) and a low limit of detection (80 μM) and a remarkable long-term stability (40 days). The intra-batch and inter-batch variation coefficients were both less than 5% (n=5). The ethanol recovery test demonstrated that the proposed biosensor offered a remarkable and accurate method for ethanol detection in the real blood samples.